Titan PowrTwin 4900 | 6900 | 8900 | 12000 Plus Operation Manuel utilisateur

POWRTWIN™

PLUS

Powered By Speeﬂo® HydraDrive™

0223 • Form No. 0537853_I

AIRLESS, HIGH-PRESSURE

SPRAYING UNIT

AIRLESS HOCHDRUCK-

SPRITZGERÄT

GROUPE DE PROJECTION À

HAUTE PRESSION

- GB - OPERATION MANUAL 2

- D - BETRIEBSANLEITUNG 22

- F - MODE D’EMPLOI 44

OPERATION MANUAL

Models:

PT4900 (230V) 0290032

PT4900 (Gas) 0290012

PT6900 (Gas) 0290013

PT8900 (Gas) 0290018

PT12000 (Gas) 0290016 (Honda)

PT12000 (Gas) 0290016K (Kohler)

2 PowrTwin Plus

GB

Warning!

Attention: Danger of injury by injection!

Airless units develop extremely high spraying pressures.

Be safety conscious!

1

2

3

Never put your ngers, hands or any other parts of the body into

the spray jet!

Never point the spray gun at yourself, other persons or animals.

Never use the spray gun without safety guard.

Do not treat a spraying injury as a harmless cut. In case of injury

to the skin through coating materials or solvents, consult a doctor

immediately for quick and expert treatment. Inform the doctor

about the coating material or solvent used.

The operating instructions state that the following points must

always be observed before starting up:

1. Faulty units must not be used.

2. Secure Titan spray gun using the safety catch on the trigger.

3. Ensure that the unit is properly earthed.

4. Check allowable operating pressure of high-pressure hose and spray

gun.

5. Check all connections for leaks.

The instructions regarding regular cleaning and maintenance of

the unit must be strictly observed.

Before any work is done on the unit or for every break in work the

following rules must be observed:

1. Release the pressure from spray gun and hose.

2. Secure the Titan spray gun using the safety catch on the trigger.

3. Switch o unit.

Original Operating Manual

PowrTwin Plus 1

GB

Contents

Page

1. Safety regulations for Airless spraying ...................................... 2

1.1 Explanation of symbols used .............................................................. 2

1.2 Electrical safety ......................................................................................... 3

1.3 Gasoline engine safety .......................................................................... 4

1.4 Fueling (gas engine) ............................................................................... 4

1.5 Setting up on uneven surfaces ........................................................... 4

2. General view of application ............................................................. 5

2.1 Application ................................................................................................ 5

2.2 Coating materials .................................................................................... 5

3. Description of unit................................................................................ 5

3.1 Airless process .......................................................................................... 5

3.2 Functioning of the unit ......................................................................... 5

3.3 System diagram - gasoline PT units .................................................. 6

3.4 System diagram - electric PT units .................................................... 7

3.5 Technical data for PT units ................................................................... 8

3.6 Airless Spray Tip Recommendation Chart ...................................... 9

3.7 Instruction manuals list ......................................................................... 9

4. Operation ................................................................................................10

4.1 Setup ..........................................................................................................10

4.2 Preparing a new sprayer ..................................................................... 11

4.3 Preparing to paint ................................................................................. 12

4.4 Painting .....................................................................................................13

4.5 Pressure relief procedure ...................................................................13

5. Cleanup ....................................................................................................14

5.1 Special cleanup instructions for use with

ammable solvents ..............................................................................14

5.2 Cleaning the sprayer ............................................................................ 14

5.3 Cleaning a clogged tip ........................................................................14

6. Maintenance..........................................................................................15

6.1 Daily maintenance ................................................................................ 15

6.2 Maintaining the lter assembly........................................................15

6.3 Maintaining the hydraulic system ...................................................16

6.4 Maintaining the uid section ............................................................ 16

6.5 Basic engine maintenance ................................................................. 17

7. Troubleshooting .................................................................................18

7.1 Airless gun ...............................................................................................18

7.2 Fluid section ............................................................................................ 18

7.3 Hydraulic motors ................................................................................... 19

7.4 Spray patterns ........................................................................................20

Warranty ...............................................................................................................21

Accessories for PT units .................................................................................66

Gun manifold assemblies (optional) ..................................................... 68/69

2 PowrTwin Plus

GB

Safety precautions

1. Safety regulations for Airless spraying

1.1 Explanation of symbols used

This manual contains information that must be read and understood

before using the equipment. When you come to an area that has one

of the following symbols, pay particular attention and make certain

to heed the safeguard.

This symbol indicates a potential hazard that

may cause serious injury or loss of life. Important

safety information will follow.

At

tention

This symbol indicates a potential hazard to you

or to the equipment. Important information that

tells how to prevent damage to the equipment or

how to avoid causes of minor injuries will follow.

Danger of skin injection

Danger of fire from solvent and paint fumes

Danger of explosion from solvent, paint fumes

and incompatible materials

Danger of injury from inhalation of harmful

vapors

i

Notes give important information which should

be given special attention.

WARNING! CALIFORNIA PROPOSITION

65 WARNING

This product can expose you to chemicals including

lead, which are known to the State of California to

cause cancer, birth defects, or other reproductive

harm.

The engine exhaust from models with gas-powered

engines can expose you to carbon monoxide which is

known to the State of California to cause cancer, birth

defects, and other reproductive harm.

For more information go to www.P65warnings.

ca.gov.

HAZARD: INJECTION INJURY

A high pressure stream produced by this equipment

can pierce the skin and underlying tissues, leading to

serious injury and possible amputation.

Do not treat a spraying injury as a harmless cut. In

case of injury to the skin through coating materials

or solvents, consult a doctor immediately for quick

and expert treatment. Inform the doctor about the

coating material or solvent used.

PREVENTION:

• NEVER aim the gun at any part of the body.

• NEVER allow any part of the body to touch the uid stream.

DO NOT allow body to touch a leak in the uid hose.

• NEVER put your hand in front of the gun. Gloves will not

provide protection against an injection injury.

• ALWAYS lock the gun trigger, shut the uid pump o and

release all pressure before servicing, cleaning the tip guard,

changing tips, or leaving unattended. Pressure will not be

released by turning o the engine. The PRIME/SPRAY valve

or pressure bleed valve must be turned to their appropriate

positions to relieve system pressure.

• ALWAYS keep tip guard in place while spraying. The tip guard

provides some protection but is mainly a warning device.

• ALWAYS remove the spray tip before ushing or cleaning the

system.

• NEVER use a spray gun without a working trigger lock and

trigger guard in place.

• All accessories must be rated at or above the maximum

operating pressure range of the sprayer. This includes spray

tips, guns, extensions, and hose.

HAZARD

: HIGH PRESSURE HOSE

The paint hose can develop leaks from wear, kinking

and abuse. A leak can inject material into the skin.

Inspect the hose before each use.

PREVENTION:

• Avoid sharp bending or kinking of the high-pressure hose. The

smallest bending radius amounts to about 20 cm.

• Do not drive over the high-pressure hose. Protect against

sharp objects and edges.

• Replace any damaged high-pressure hose immediately.

• Never repair defective high-pressure hoses yourself!

• Electrostatic charging of spray guns and the high-pressure

hose is discharged through the high-pressure hose. For this

reason the electric resistance between the connections of the

high-pressure hose must be equal to or lower than 1M.

• For reasons of function, safety and durability use only original

Titan high-pressure hoses.

• Before each use, check all hoses for cuts, leaks, abrasion

or bulging of cover. Check for damage or movement of

couplings. Immediately replace the hose if any of these

conditions exist. Never repair a paint hose. Replace it with

another earthed high-pressure hose.

• Make sure power cord, air hose and spray hoses are routed in

such a manner to minimize slip, trip and fall hazard.

HAZARD: EXPLOSION OR FIRE

Flammable vapors, such as solvent and paint vapors,

in work area can ignite or explode.

PREVENTION:

• Use equipment only in well ventilated area. Keep a good

supply of fresh air moving through the area to keep the air

within the spray area free from accumulation of ammable

vapors. Keep pump assembly in well ventilated area. Do not

spray pump assembly.

• Electric models only - Do not use materials with a ashpoint

below 38º C (100º F). Flashpoint is the temperature at which a

uid can produce enough vapors to ignite.

• Gas models only - Do not ll fuel tank while engine is running

or hot; shut o engine and allow to cool. Fuel is ammable

and can ignite or explode if spilled on a hot surface.

• Eliminate all ignition sources, such as pilot lights, cigarettes,

portable electric lamps and plastic drop cloths (potential static

arc).

PowrTwin Plus 3

GB

Safety precautions

• Keep work area free of debris, including solvent, rags and

gasoline.

• Do not plug or unplug power cords, or turn power or light

switches on or o when ammable vapors are present.

• Ground equipment and conductive objects in work area.

Make sure the grounding cable (not equipped) is connected

from the grounding lug to a true earth ground.

• Use only grounded hoses.

• Hold spray gun rmly to the side of a grounded pail when

triggering into pail.

• If there is static sparking or if you feel a shock, stop operation

immediately.

• Know the contents of the paint and solvents being sprayed.

Read all Material Safety Data Sheets (MSDS) and container

labels provided with the paints and solvents. Follow the paint

and solvent manufacturer’s safety instructions.

• Do not use a paint or solvent containing halogenated

hydrocarbons. Such as chlorine, bleach, mildewcide,

methylene chloride and trichloroethane. They are not

compatible with aluminum. Contact the coating supplier

about compatibility of material with aluminum.

• Keep a re extinguisher in work area.

HAZARD: HAZARDOUS VAPORS

Paints, solvents, and other materials can be harmful

if inhaled or come in contact with body. Vapors can

cause severe nausea, fainting, or poisoning.

PREVENTION:

• Wear respiratory protection when spraying. Read all

instructions supplied with the mask to be sure it will provide

the necessary protection.

• All local regulations regarding protection against hazardous

vapors must be observed.

• Wear protective eyewear.

• Protective clothing, gloves and possibly skin protection cream

are necessary for the protection of the skin. Observe the

regulations of the manufacturer concerning coating materials,

solvents and cleaning agents in preparation, processing and

cleaning units.

HAZARD: GENERAL

This product can cause severe injury or property

damage.

PREVENTION:

• Follow all appropriate local, state, and national codes

governing ventilation, re prevention, and operation.

• Pulling the trigger causes a recoil force to the hand that is

holding the spray gun. The recoil force of the spray gun is

particularly powerful when the tip has been removed and

a high pressure has been set on the airless pump. When

cleaning without a spray tip, set the pressure control knob to

the lowest pressure.

• Use only manufacturer authorized parts. User assumes all

risks and liabilities when using parts that do not meet the

minimum specications and safety devices of the pump

manufacturer.

• ALWAYS follow the material manufacturer’s instructions for

safe handling of paint and solvents.

• Clean up all material and solvent spills immediately to prevent

slip hazard.

• Wear ear protection. This unit can produce noise levels above

85 dB(A).

• Never leave this equipment unattended. Keep away from

children or anyone not familiar with the operation of airless

equipment.

• Do not spray on windy days.

• The device and all related liquids (i.e. hydraulic oil) must be

disposed of in an environmentally friendly way.

1.2 Electric Safety

Electric models must be earthed. In the event of an electrical short

circuit, earthing reduces the risk of electric shock by providing an

escape wire for the electric current. This product is equipped with

a cord having an earthing wire with an appropriate earthing plug.

Connection to the mains only through a special feed point, e.g.

through an error protection insallation with INF < 30 mA.

DANGER — Work or repairs at the electrical

equipment may only be carried out by a skilled

electrician. No liability is assumed for incorrect

installation. Switch the unit o. Before all repair

work, unplug the power plug from the outlet.

Danger of short-circuits caused by water ingressing into the electrical

equipment. Never spray down the unit with high-pressure or high-

pressure steam cleaners.

Work or repairs at the electrical equipment:

These may only be carried out by a skilled electrician. No liability is

assumed for incorrect installation.

Operating Temperature

This equipment will operate correctly in its intended ambient, at a

minimum between +10°C and +40°C.

Relative Humidity

The equipment will operate correctly within an environment at 50%

RH, +40°C. Higher RH may be allowed at lower temperatures.

Measures shall be taken by the Purchaser to avoid the harmful eects

of occasional condensation.

Altitude

This equipment will operate correctly up to 2100 m above mean sea

level.

Transportation and Storage

This equipment will withstand, or has been protected against,

transportation and storage temperatures of -25°C to +55°C and for

short periods up to +70°C.

It has been packaged to prevent damage from the eects of normal

humidity, vibration and shock.

1.3 Gasoline Engine Safety

1. Gas engines are designed to give safe and dependable service

if operated according to instructions. Read and understand

the engine manufacturer’s Owner’s Manual before operating

the engine. Failure to do so could result in personal injury or

equipment damage.

2. To prevent re hazards and to provide adequate ventilation,

keep the engine at least 1 meter (3 feet) away from buildings

and other equipment during operation. Do not place

ammable objects close to the engine.

3. People who are not operating the device must stay away from

the area of operation due to a possibility of burns from hot

engine components or injury from any equipment the engine

may be used to operate.

4. Know how to stop the engine quickly, and understand the

operation of all controls. Never permit anyone to operate the

engine without proper instructions.

5. Gasoline is extremely ammable and is explosive under

certain conditions.

6. Refuel in a well-ventilated area with the engine stopped. Do

not smoke or allow ames or sparks in the refueling area or

where gasoline is stored.

4 PowrTwin Plus

GB

Safety precautions

7. Do not overll the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

8. Be careful not to spill fuel when refueling. Fuel vapor or

spilled fuel may ignite. If any fuel is spilled, make sure the area

is dry before starting the engine.

9. Never run the engine in an enclosed or conned area. Exhaust

contains poisonous carbon monoxide gas; exposure may

cause loss of consciousness and may lead to death.

10. The muer becomes very hot during operation and remains

hot for a while after stopping the engine. Be careful not to

touch the muer while it is hot. To avoid severe burns or re

hazards, let the engine cool before transporting it or storing it

indoors.

11. Never ship/transport sprayer with gasoline in the tank.

DO NOT use this equipment to spray water or acid.

Attention

Do not lift by cart handle when loading or unloading.

Device is very heavy. Three-person lift is required.

1.4 Fueling (gas engine)

Gasoline is extremely flammable and is explosive

under certain conditions.

Attention

Do not overll the gas tank. Overlling can cause

the gas cap to become clogged with any particles

in the gasoline which can cause a vaccum. Read

the gas engine’s instruction manual for fueling

instructions.

Fuel Specications

• Use automotive gasoline that has a pump octane number of

86 or higher, or that has a research octane number of 91 or

higher. Use of a lower octane gasoline can cause persistent

“pinging” or heavy “spark knock” (a metallic rapping noise)

which, if severe, can lead to engine damage.

iIf “spark knock” or “pinging” occurs at a steady

engine speed under normal load, change brands of

gasoline. If spark knock or pinging persists, consult

an authorized dealer of the engine manufacturer.

Failure to do so is considered misuse, and damage

caused by misuse is not covered by the engine

manufacturer’s limited warranty.

Occasionally you may experience light spark knock

while operating under heavy loads. This is no

cause for concern, it simply means your engine is

operating eciently.

• Unleaded fuel produces fewer engine and spark plug deposits

and extends the life of the exhaust system components.

• Never use stale or contaminated gasoline or an oil/gasoline

mixture. Avoid getting dirt, dust, or water in the fuel tank.

Gasolines Containing Alcohol

If you decide to use a gasoline containing alcohol (gasohol), be

sure its octane rating is at least as high as that recommended by

the engine manufacturer. There are two types of “gasohol”: one

containing ethanol, and the other containing methanol. Do not use

gasohol that contains more than 10% ethanol. Do not use gasoline

containing methanol (methyl or wood alcohol) that does not also

contain co-solvents and corrosion inhibitors for methanol. Never

use gasoline containing more than 5% methanol, even if it has co-

solvents and corrosion inhibitors.

iFuel system damage or engine performance

problems resulting from the use of fuels that contain

alcohol is not covered under the warranty. The

engine manufacturer cannot endorse the use of

fuels containing methanol since evidence of their

suitability is incomplete at this time.

Before buying gasoline from an unfamiliar station, try

to nd out if the gasoline contains alcohol. If it does,

conrm the type and percentage of alcohol used. If

you notice any undesirable operating characteristics

while using a gasoline that contains alcohol, or one

that you think contains alcohol, switch to a gasoline

that you know does not contain alcohol.

1.5 Setting up on uneven surfaces

The front side of the unit must point downwards to prevent sliding

away.

PowrTwin Plus 5

GB

General view of application Description of unit

2. General view of application

2.1 Application

Priming and nal coating of large areas, sealing, impregnation,

construction sanitation, façade protection and renovation, rust

protection and building protection, roof coating, roof sealing,

concrete sanitation, as well as heavy corrosion protection.

Examples of objects to be sprayed

Large-scale construction sites, cooling towers, bridges, sewage

treatment plants and terraces.

2.2 Coating materials

Processible coating materials

i

Pay attention to the Airless quality of the coating

materials to be processed.

Latex paint, dispersion paints, re protection and thick lm materials,

zinc dust and micaceous iron ore paints, Airless spray primer,

sprayable glue, anti-corrosive agents, thick coating materials and

bitumen-like coating materials.

No other materials should be used for spraying without Titan’s

approval.

Filtering

In spite of the high-pressure lter, ltering of the coating material is

to be recommended in general (except when processing airless joint

ller).

Stir coating material before commencement of work.

iMake sure when stirring with motor-driven agitators

that no air bubbles are stirred in. Air bubbles disturb

when spraying and can, in fact, lead to interruption

of operation.

Viscosity

It is possible to work with high-viscosity coating materials with the

devices.

If highly viscous coating materials cannot be sucked up, they must be

diluted in accordance with the manufacturer’s instruction.

Two-component coating material

The appropriate processing time must be adhered to exactly. Within

this time rinse through and clean the unit meticulously with the

appropriate cleaning agents.

Coating materials with sharp-edged additional materials

These have a strong wear and tear eect on valves, high-pressure

hose, spray gun and tip. The durability of these parts can be reduced

appreciably through this.

3. Description of unit

3.1 Airless process

The main area of application are thick layers of highly viscous coating

material for large areas and a high consumption of material.

A piston pump takes in the coating material by suction and conveys it

to the tip. Pressed through the tip at a pressure of up to a maximum

of 3300-3600 psi (228-248 bar, 24.4-24.8 MPa), the coating material is

atomised. This high pressure has the eect of micro ne atomisation

of the coating material.

As no air is used in this process, it is described as an AIRLESS process.

This method of spraying has the advantages of nest atomisation,

cloudless operation and a smooth, bubble-free surface. As well as

these, the advantages of the speed of work and convenience must be

mentioned.

3.2 Functioning of the unit

The following section contains a brief description of the technical

construction for better understanding of the function.

TITAN PowrTwin Plus (PT) are high-pressure spraying units driven by

either a gasoline engine or electric motor.

The gasoline engine or electric motor (g. 1, item 1) drives the

hydraulic pump (3) by means of a V-belt which is under the belt cover

(2). Hydraulic oil ows to the Speeo® HydraDrive™ hydraulic motor

(4) and then moves the piston up and down in the material feed

pump (5).

The inlet valve is opened automatically by the upwards movement

of the piston. The outlet valve is opened when the piston moves

downward.

The coating material ows under high pressure through the high-

pressure hose to the spray gun. When the coating material exits from

the tip it atomises.

The pressure control valve (6) controls the volume and the operating

pressure of the coating material.

2

4

56

3

1

6 PowrTwin Plus

GB

Description of unit

3.3 System diagram - gasoline PT units

1 Extractable handle

2 Speeo® HydraDrive™ hydraulic motor

3 Oil cup for separating oil (separating oil prevents increased

wear and tear of the packings)

4 Pressure control knob

5 Relief valve handle: Turn left for circulation k

Turn right for spray p

6 High-pressure lter

7 High-pressure hose outlet

8 V-belt under the belt cover

9 Bleed hose

10 Ball valve: horizontal position – hydraulic motor switched o

vertical position – hydraulic motor switched on

11 Suction tube

12 Oil measuring stick

13 Gasoline engine

1

7

8

5

4

6

2

3

9

10

11

12

13

10

3

PowrTwin Plus 7

GB

Description of unit

3.4 System diagram - electric PT units

1 Extractable handle

2 Speeo® HydraDrive™ hydraulic motor

3 Oil cup for separating oil (separating oil prevents increased

wear and tear of the packings)

4 Pressure control knob

5 Relief valve handle: Turn left for circulation k

Turn right for spray p

6 High-pressure lter

7 High-pressure hose outlet

8 V-belt under the belt cover

9 Bleed hose

10 Ball valve: horizontal position – hydraulic motor switched o

vertical position – hydraulic motor switched on

11 Suction tube

12 Oil measuring stick

13 Electric motor (230V)

14 ON/OFF switch

15 Control lamp that shows unit operational

16 Power Cord

8

9

10

11

13

12

14

15

16

1

7

5

4

6

2

3

10

3

8 PowrTwin Plus

GB

Description of unit

PT4900 Plus (230V) PT4900 Plus (gas) PT6900 Plus PT8900 Plus PT12000 Plus

Gasoline engine, power

Honda -------- 163cc, 4.8 Hp 163cc, 4.8 Hp 196cc, 5.5 Hp 270cc, 8.5 Hp

Kohler -------- -------- -------- -------- 277cc, 9.5 Hp

Fuel Capacity

-------- 0.83 US gal (3.1 l) 0.83 US gal (3.1 l) 0.83 US gal (3.1 l) 1.6 US gal (6.06 l)

Voltage

230 V~, 50 Hz -------- -------- -------- --------

Capacity

2.6 kW -------- -------- -------- --------

Power Cord

3 x 2.5 mm – 6 m -------- -------- -------- --------

Fuse Protection

16 A -------- -------- -------- --------

Max. operating pressure

22.8 MPa (228 bar, 3300 psi) 24.8 MPa (248 bar,

3600 psi)

Max. sound pressure level

80 dB (A)* 92 dB (A)* 98 dB (A)*

Max. size of tip with a spray gun

1-gun 0.038” – 0.97 mm 0.044” – 1.12 mm 0.050” – 1.27 mm 0.054” – 1.37 mm 0.058” – 1.47 mm

2-gun 0.027” – 0.69 mm 0.031” – 0.79 mm 0.035” – 0.89 mm 0.038” – 0.96 mm 0.040” – 1.01 mm

3-gun 0.021” – 0.53 mm 0.025” – 0.64 mm 0.029” – 0.74 mm 0.032” – 0.81 mm 0.034” – 0.86 mm

4-gun -------- -------- 0.025” – 0.64 mm 0.028” – 0.71 mm 0.030” – 0.76 mm

5-gun -------- -------- -------- 0.024” – 0.61 mm 0.026” – 0.66 mm

6-gun -------- -------- -------- -------- 0.024” – 0.61 mm

Max. volume ow

1.1 gal (4.2 l)/min 1.5 gal (5.7 l)/min 2.25 gal (8.5 l)/min 2.5 gal (9.5 l)/min 3.15 gal (11.9 l)/min

Weight

139 lbs. (63 kg) 132 lbs. (60 kg) 139 lbs. (63 kg) 154 lbs. (70 kg) 183 lbs. (83 kg)

Max. viscosity

50.000 mPa·s 65.000 mPa·s

Dimensions L x W x H

37.2” x 26.8” x 35” (946 x 680 x 890 mm)

42.5” x 27” x 31” (1080 x

686 x 866 mm)

46” x 27” x 31” (1168 x

686 x 866 mm)

Max. temperature of the coating material

109ºF (43° C)

Filter insert (standard equipment)

50 mesh, 18 in25 mesh, 18 in2

Hydraulic oil lling quantity

5.9 l (1.56 gal) CoolFlo

Max. tire pressure

0.2 MPa (2 bar)

Special high-pressure hose

DN 6 mm, 15 m (50’ x 1/4”), connection thread NPSM 1/4

* Place of measurement: 1 m distance from unit and 1.60 m above reverberant oor, 120 bar (12 MPa) operating pressure.

3.5 Technical data for PT units

PowrTwin Plus 9

GB

Description of unit

3.6 Airless Spray Tip Recommendation Chart

Viscosity Filter Mesh Coating Orice Range Synergy™ (Fine Finish)

Light 100-150 Varnishes .009 - .011 .008 - .010

Lacquer Finishes (clear) .009 - .011 .008 - .010

Sanding Sealers .009 - .011 .008 - .010

Shellac (clear) .009 - .013 .008 - .012

Transparent Stain .011 - .013 .010 - .012

Water Sealers (clear) .011 - .013 .010 - .012

Medium 60-100 Solid Stains .013 - .015

Exterior House Paints .013 - .017

Interior Wall Paints .013 - .017

Interior & Exterior Primers .017 - .019

Heavy 30-60 Commercial Grade

Architectural Coatings .017 - .019

Interior Wall Paints .017 - .019

Interior Wall Primers .017 - .019

Dry Fall (quick dry) .019 - .023

One Coat, Primer-Finish Paints .019 - .023

Extra Heavy 0 Elastomerics .021 - .031

Pigmented Waterproofers .021 - .027

Block Filler .025 - .031

Orice sizes recommended on this chart are based on fan widths between 8 inches (20 cm) and 12 inches (30 cm)

3.7 Instruction manuals list

The following is a list of the available instruction manuals for this unit.

Online items can be downloaded at www.titantool.com

Description Form # How to Find

Operation Manuals

GB/D/F 537853 • included with unit

• online

E/I/P 537854

NL/DK/S 537855

RFB 537867

Service Manual, Spare Parts

GB/D/F 2439109 • online

E/I/P 2439114

NL/DK/S 2439115

RFB 2439116

10 PowrTwin Plus

GB

Operation

4. Operation

This equipment produces a fluid stream at extremely

high pressure. Read and understand the warnings

in the Safety Precautions section at the front of this

manual before operating this equipment.

4.1 Setup

1. Make sure the siphon hose (g. 4, 1) is connected to the uid

section (2) and the bleed hose (3) is connected to the bleed

valve (4). They each have factory installed PTFE tape on the

male end of the hoses and should be wrench tight.

3

1

4

2

2. Attach a minimum of 15m of nylon airless spray hose to the

sprayer. Do not use PTFE tape or thread sealant on the spray

hose connection.

3. Attach an airless spray gun to the spray hose. Do not attach

the tip to the spray gun yet. Remove the tip if it is already

attached.

a. To use two guns, remove the plug from the second gun outlet

on the lter assembly. Connect a hose and gun to the outlet.

iFor multiple gun operation, connect a multiple gun

manifold to the single gun outlet. Connect a hose

and gun to each outlet. Make sure the second gun

outlet remains plugged. See “Technical Data”,

Section 3.5 to determine number of guns and

maximum spray tip sizes.

4. Fill the oil cup 1/2 full with Piston Lube (P/N 314-480). This

extends packing life.

Attention

Piston Lube prevents increased wear and tear to the

packings.

5. Check the hydraulic uid level daily before starting the

sprayer. The hydraulic uid level should be at the “Full” mark

on the dipstick. Refer to the Maintenance section of this

manual for hydraulic system maintenance instructions.

Attention

Use of Titan’s Coolflo™ Hydraulic Fluid (P/N 430-361)

is mandatory in the hydraulic system. Do not use

any other hydraulic fluid. Use of any other hydraulic

fluid may seriously damage the hydraulic system

and will void the warranty.

6. For gas models, check the engine oil level daily before starting

the sprayer. The gasoline engine oil level is determined by

the engine manufacturer. Refer to the engine manufacturer’s

service manual supplied with this sprayer.

7. For electric models, use a 20 amp service outlet. Always

locate the electric model within 10 to 15 feet of the service

outlet. Use a short electric cable and a long paint hose. Any

extension cord will create some voltage drop. If an extension

cord is necessary, use only a grounded 3-wire #12 extension

cord.

8. Make sure the sprayer is earthed. All sprayers are equipped

with a earthing lug. An earthing cable (not supplied) should

be used to connect the sprayer to a true earth ground.

Check your local electrical regulations for detailed earthing

instructions.

Proper earthing is important. This applies to both

gas and electric powered models. The passage of

some materials through the nylon uid hose will

build up a static electric charge, which if discharged,

could ignite solvent vapors present and create an

explosion.

9. Strain all paints with a nylon strainer to ensure trouble free

operation and freedom from frequent cleaning of the inlet

screen and gun lter.

10. Make sure the spray area is well ventilated to prevent

hazardous operation with volatile solvents or exhaust fumes.

If lacquer or other flammable materials are to be

sprayed, ALWAYS locate the sprayer outside the

immediate spraying area. Failure to do so may cause

an explosion.

11. Locate the sprayer outside the immediate spraying area to

avoid clogged air intake of the engine or electric motor with

overspray.

PowrTwin Plus 11

GB

Operation

4.2 Preparing a New Sprayer

If this unit is new, it is shipped with test uid in the uid section to

prevent corrosion during shipment and storage. This uid must be

thoroughly cleaned out of the system with mineral spirits before you

begin spraying.

Attention

Always keep the trigger lock on the spray gun in the

locked position while preparing the system.

1. Place the siphon tube into a container of mineral spirits.

2. Place the bleed hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to its

lowest pressure setting (g 7, 1).

4. Open the hydraulic shut-o valve (2) located on the hydraulic

pressure hose. The handle should be in line with the hose.

5. Open the bleed valve (3) by turning it fully counterclockwise.

1

3

2

6. Start the engine or turn on the electric motor.

a. To start the gas engine (g. 8),

• move the fuel valve lever (2) to the open position,

• move the throttle lever (3) to its middle point,

• move the choke lever (4) to the closed position for a cold

engine or to the open position for a warm engine,

• turn the engine switch (1) to the ON position, and

• pull the starter rope (5) briskly until the engine starts.

b. To start the electric motor, move the ON/OFF switch to the ON

position.

2

4

1

3

5

7. Turn the pressure control knob (g. 7, 1) clockwise

approximately 1/3 of the way down to increase pressure until

the sprayer cycles evenly and solvent ows freely from the

bleed hose.

8. Allow the sprayer to run for 15–30 seconds to ush the test

uid out through the bleed hose and into the waste container.

9. Turn o the sprayer.

a. To turn o the gas engine,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

b. To turn o the electric motor,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the ON/OFF switch to the OFF position.

Earth the gun by holding it against the edge of the

metal container while flushing. Failure to do so may

lead to a static electric discharge, which may cause

a fire.

14. Trigger the gun into the metal waste container until the old

solvent is gone and fresh solvent is coming out of the gun.

15. Lock the gun by turning the gun trigger lock to the locked

position (g 10).

16. Set down the gun and increase the pressure by turning the

pressure control knob slowly clockwise to its highest setting.

17. Check the entire system for leaks. If leaks occur, turn the

sprayer o and follow the “Pressure Relief Procedure” in this

manual before tightening any ttings or hoses.

18. Follow the “Pressure Relief Procedure” (section 4.5) in this

manual before changing from solvent to paint.

Be sure to follow the Pressure Relief Procedure when

shutting the unit down for any purpose, including

servicing or adjusting any part of the spray system,

changing or cleaning spray tips, or preparing for

cleanup.

4.3 Preparing to Paint

Before painting, it is important to make sure that the uid in the

system is compatible with the paint that is going to be used.

iIncompatible uids and paint may cause the valves

to become stuck closed, which would require

disassembly and cleaning of the sprayer’s uid

section.

Attention

Always keep the trigger lock on the spray gun in the

locked position while preparing the system.

1. Place the siphon tube into a container of the appropriate

solvent for the material being sprayed.

iIf you are spraying a water-based latex, ush with

warm, clean water. If you are using any other

material, check with the material manufacturer for a

compatible solvent.

2. Place the bleed hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to its

lowest pressure setting (g 7, 1).

4. Open the hydraulic shut-o valve (2) located on the hydraulic

pressure hose. The handle should be in line with the hose.

5. Open the bleed valve (3) by turning it fully counterclockwise.

6. Start the engine or turn on the electric motor.

a. To start the gas engine (g. 8),

• move the fuel valve lever (2) to the open position,

• move the throttle lever (3) to its middle point,

• move the choke lever (4) to the closed position for a cold

engine or to the open position for a warm engine,

• turn the engine switch (1) to the ON position, and

• pull the starter rope (5) briskly until the engine starts.

b. To start the electric motor, move the ON/OFF switch to the ON

position.

7. Turn the pressure control knob (1) clockwise approximately

1/3 of the way down to increase pressure until the sprayer

cycles evenly and solvent ows freely from the bleed hose.

8. Allow the sprayer to run for 15–30 seconds to ush the test

uid out through the bleed hose and into the waste container.

9. Turn o the sprayer.

a. To turn o the gas engine,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

b. To turn o the electric motor,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the ON/OFF switch to the OFF position.

i

Make sure that the spray gun does not have a tip or

tip guard installed.

10. Close the bleed valve by turning it fully clockwise.

11. Start the engine or turn on the electric motor.

12. Turn the pressure control knob clockwise approximately 1/3

of the way down to increase pressure.

13. Unlock the gun by turning the gun trigger lock to the

unlocked position.

12 PowrTwin Plus

GB

Operation

4.4 Painting

1. Place the siphon hose into a container of paint.

2. Place the bleed hose into a metal waste container.

3. Turn the pressure control knob fully counterclockwise to its

lowest pressure setting (g 7, 1).

4. Open the hydraulic shut-o valve (2) located on the hydraulic

pressure hose. The handle should be in line with the hose.

5. Open the bleed valve (3) by turning it fully counterclockwise.

6. Start the engine or turn on the electric motor.

a. To start the gas engine (g. 8),

• move the fuel valve lever (2) to the open position,

• move the throttle lever (3) to its middle point,

• move the choke lever (4) to the closed position for a cold

engine or to the open position for a warm engine,

• turn the engine switch (1) to the ON position, and

• pull the starter rope (5) briskly until the engine starts.

b. To start the electric motor, move the ON/OFF switch to the ON

position.

7. Turn the pressure control knob (1) clockwise approximately

1/3 of the way down to increase pressure until the sprayer

cycles evenly and solvent ows freely from the bleed hose.

8. Turn o the sprayer.

a. To turn o the gas engine,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

b. To turn o the electric motor,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the ON/OFF switch to the OFF position.

9. Remove the bleed hose from the waste container and place it

into the container of paint.

10. Close the bleed valve by turning it fully clockwise.

11. Start the engine or turn on the electric motor.

12. Turn the pressure control knob clockwise approximately 1/3

of the way down to increase pressure.

13. Unlock the gun by turning the gun trigger lock to the

unlocked position.

Earth the gun by holding it against the edge of the

metal container while flushing. Failure to do so may

lead to a static electric discharge, which may cause

a fire.

14. Trigger the gun into the metal waste container until all air and

solvent is ushed from the spray hose and paint is owing

freely from the gun.

15. Lock the gun by turning the gun trigger lock to the locked

position (g 10).

16. Turn o the sprayer.

17. Attach tip guard and tip to the gun as instructed by the tip

guard or tip manuals.

POSSIBLE INJECTION HAZARD. Do not spray

without the tip guard in place. Never trigger the

gun unless the tip is in either the spray or the unclog

position. Always engage the gun trigger lock before

removing, replacing or cleaning tip.

18. Start the engine or turn on the electric motor.

PowrTwin Plus 13

GB

Operation

19. Increase the pressure by turning the pressure control knob

slowly clockwise and test the spray pattern on a piece of

cardboard. Adjust the pressure control knob until the spray

from the gun is completely atomized.

iTurning the pressure up higher than needed to

atomize the paint will cause premature tip wear and

additional overspray.

4.5 Pressure Relief Procedure

Be sure to follow the Pressure Relief Procedure when

shutting the unit down for any purpose, including

servicing or adjusting any part of the spray system,

changing or cleaning spray nozzles, or preparing for

cleanup.

1. Lock the spray gun by turning the gun trigger lock to the

locked position.

2. Turn o the sprayer.

a. To turn o the gas engine,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the throttle lever to the slow position, and

• turn the engine switch to the OFF position.

b. To turn o the electric motor,

• set the pressure to minimum by turning the pressure control

knob fully counterclockwise,

• move the ON/OFF switch to the OFF position.

3. Close the hydraulic shut-o valve on the hydraulic pressure

hose.

4. Unlock the gun by turning the gun trigger lock to the

unlocked position.

5. Hold the metal part of the gun rmly to the side of a metal

waste container to earth the gun and avoid a build up of static

electricity.

6. Trigger the gun to remove any pressure that may still be in the

hose.

7. Lock the gun by turning the gun trigger lock to the locked

position.

8. Place the bleed hose into the metal waste container.

9. Open the bleed valve by turning it fully counterclockwise.

14 PowrTwin Plus

GB

Cleanup

5. Cleanup

Attention

The sprayer, hose, and gun should be cleaned

thoroughly after daily use. Failure to do so permits

material to build up, seriously aecting the

performance of the unit.

Always spray at minimum pressure with the gun

nozzle tip removed when using mineral spirits or

any other solvent to clean the sprayer, hose, or

gun. Static electricity buildup may result in a re or

explosion in the presence of ammable vapors.

5.1 Special cleanup instructions for use with

ammable solvents

• Always ush spray gun preferably outside and at least one hose

length from spray pump.

• If collecting ushed solvents in a one gallon metal container,

place it into an empty ve gallon container, then ush solvents.

• Area must be free of ammable vapors.

• Follow all cleanup instructions.

5.2 Cleaning the sprayer

1. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual, section 4.5.

2. Remove the gun tip and tip guard and clean with a brush

using the appropriate solvent.

3. Place the siphon tube into a container of the appropriate

solvent.

Attention

Use only compatible solvents when cleaning

out oil based enamels, lacquers, coal tar, and

epoxies. Check with the uid manufacturer for the

recommended solvent.

4. Place the bleed hose into a metal waste container.

5. Set the pressure to minimum by turning the pressure control

knob (1) fully counterclockwise.

6. Open the hydraulic shut-o valve located on the hydraulic

pressure hose (2). The handle should be in line with the hose.

7. Open the bleed valve (3) by rotating the bleed valve handle

fully counterclockwise.

1

3

2

8. Start the engine or turn on the electric motor.

9. Allow the solvent to circulate through the sprayer and

ush the paint out of the bleed hose into the metal waste

container.

10. Turn o the sprayer.

11. Close the bleed valve by rotating the bleed valve handle fully

clockwise.

12. Start the engine or turn on the electric motor.

Earth the gun by holding it against the edge of the

metal container while flushing. Failure to do so may

lead to a static electric discharge, which may cause

a fire.

13. Trigger the gun into the metal waste container until the paint

is ushed out of the hose and solvent is coming out of the

gun.

14. Continue to trigger the spray gun into the waste container

until the solvent coming out of the gun is clean.

iFor long-term, cold weather storage, or any freezing

temperature exposure pump mineral spirits through

the entire system.

For short-term storage not exposed to freezing

temperatures when using latex paint, pump water

mixed with Titan Liquid Shield through the entire

system (see Accessories section of this manual

for part number and product label for dilution

instructions).

15. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual.

16. Store the sprayer in a clean, dry area.

Attention

Do not store the sprayer under pressure.

5.3 Cleaning a Clogged Tip

1. Follow the “Pressure Relief Procedure” in the Operation

section of this manual.

2. If the tip clogs, rotate the tip handle 180° until the arrow on

the handle is facing the opposite of the spray direction and

the handle clicks in the reverse position.

3. Trigger the gun once so that the pressure can blow the clog

out. NEVER use the tip in the reverse position for more than

ONE trigger pull at a time. This procedure can be repeated

until the tip is free of clogging.

The flow from the spray tip is at very high pressure.

Contact with any body part may be dangerous. Do

not place finger on gun outlet. Do not point the gun

at any person. Never operate the spray gun without

the proper tip guard.

PowrTwin Plus 15

GB

Maintenance

6. Maintenance

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to reduce the

risk of an injection injury, injury from moving parts

or electric shock. Always unplug the sprayer before

servicing!

6.1 Daily Maintenance

Two daily procedures are required for routine operator maintenance

on this sprayer:

A. Lubricating the upper packings.

B. Cleaning the lter screen

A) Lubricating the Upper Packings

1. Clean out the paint that has seeped past the upper packings

into the packing oil reservoir (g. 13, item 1) above the uid

section.

2. Fill the packing oil reservoir 1/2 full with Piston Lube (P/N 314-

480) supplied by the factory. This will extend packing life.

1

i

Do not over-ll the reservoir so that it overows and

drips into the paint.

B) Cleaning the Filter Screen

1. The lter screen will clog and must be cleaned at least once a

day.

2. Loosen the hex nut (g. 14, item 1) that secures the lter

screen to the siphon tube.

3. Remove the lter screen (2) from the bottom of the siphon

tube.

4. Clean thoroughly with the appropriate solvent.

2

1

6.2 Maintaining the Filter Assembly

Clean the lter regularly. Dirty or clogged lters can greatly reduce

ltering ability and cause a number of system problems including

poor spray patterns, clogged spray tips, etc.

Cleaning (Fig. 15)

To clean the lter, perform the following procedure.

1. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual.

2. Remove the lter cap assembly (1) and spring (2).

3. Pull the lter element with ball straight (3) out of the lter

body (4).

4. Clean inside the lter body, lter element with ball, and lter

cap assembly using the appropriate solvent.

iUse care in handling parts as dirt, debris, scratches,

or nicks may prevent o-rings or gaskets from sealing.

This lter element lters from the inside out. Be sure

to clean the lter element thoroughly on the inside.

Soak in solvent to loosen hardened paint or replace.

1

3

7

8

5

6

4

2

Inspection (Fig. 15)

Inspect all parts of the lter assembly before reassembly.

1. Inspect the ball inside the lter element. If the ball has

pressure cuts or scratches, replace the lter element.

a. If the ball is cut, remove the PTFE o-ring (5) using an o-ring pick

and remove the carbide seat (6).

b. Check the seat for nicks or grooves. If the seat is damaged,

replace.

i

Removal of the PTFE o-ring will damage the o-ring

and require replacement.

2. Remove the spring (2) from the spring guide on the lter cap.

a. Measure the length of the spring uncompressed. If it measures

less than 3/4” from end to end, replace.

b. Push the spring back onto the spring guide until it “snaps” back

into position.

3. Inspect the two PTFE gaskets (7,8) and the PTFE o-ring (5) for

deformity, nicks, or cuts. Replace, if needed.

i

The PTFE gaskets, PTFE o-ring, and spring are

packaged in Filter Service Kit P/N 930-050.

16 PowrTwin Plus

GB

Maintenance

Reassembly (Fig. 15)

After cleaning and inspecting all parts, reassemble the lter.

1. Place the carbide seat (6) into the lter body (4). Make sure

the beveled side of the seat is facing up.

2. Place the PTFE o-ring (5) into the groove on the outer

diameter of the carbide seat (6).

3. Place the lter element with ball (3) into the lter body (4).

i

The top and bottom of the lter element with ball

are identical.

4. Push the spring (2) back onto the spring guide of the lter cap

(1) until it “snaps” back into position, if not already done.

5. Place the thin PTFE gasket (8) onto the step at the top of the

lter body (4).

6. Place the thick PTFE gasket (7) onto the top of the thin gasket

(8).

7. Tighten the lter cap assembly (1) onto the lter body (4).

1

3

7

8

5

6

4

2

6.3 Maintaining the Hydraulic System

Attention

Use of Titan’s Coolflo™ Hydraulic Fluid is mandatory

in the PowrTwin Plus hydraulic system. Do not use

any other hydraulic fluid. Use of any other hydraulic

fluid may seriously damage the hydraulic system

and will void the warranty.

1. Check the hydraulic uid daily. It should be at the “Full”

mark (g. 16, item 1) on the dipstick (2). If it is low, add only

Titan Coolo™ Hydraulic Fluid (P/N 430-361). Never add

or change hydraulic uid except in a clean, dust-free area.

Contamination of the hydraulic uid will shorten hydraulic

pump life and may void warranty.

1

2

3

2. Change the hydraulic uid every twelve months. Drain the

old uid from the tank and ll with 6.25 quarts of hydraulic

uid. Start the sprayer at just enough pressure to operate the

uid section. Run the sprayer at this low pressure for at least

5 minutes. This removes air from the system. Check the uid

level after this procedure. Do not over-ll.

iWhen replacing the hydraulic filter (3) during a

fluid change, it may be necessary to add up to one

additional quart of hydraulic fluid.

3. The hydraulic system has an external, replaceable hydraulic

lter. Change the lter every twelve months.

4. The hydraulic pump should not be serviced in the eld. If

service on the hydraulic pump is required, it must be returned

to Titan.

6.4 Maintaining the Fluid Section

If the sprayer is going to be out of service for an extended period of

time, it is recommended that following cleanup, a kerosene and oil

mixture be introduced as a preservative. Packings may tend to dry

out from lack of use. This is particularly true of the upper packing

set for which upper packing lubricant Piston Lube (P/N 314-480) is

recommended in normal usage.

If the sprayer has been out of service for an extended period of time,

it may be necessary to prime the pump with solvent. It is extremely

important that the threads on the siphon hose coupling are properly

sealed. Any air leakage will produce erratic operation of the sprayer

and may damage the system. The up and the down strokes should

be approximately equal in time (one should not be faster than the

other). A fast up or down stroke may indicate air in the system or

malfunctioning valve or seats (see the Troubleshooting section).

PowrTwin Plus 17

GB

Maintenance

6.5 Basic Engine Maintenance (gas engine)

• For detailed engine maintenance and technical specications

refer to the separate gasoline engine manual.

• All service to the engine should be performed by a dealer

authorized by the engine manufacturer.

• Use a premium quality motor oil. 10W30 is recommended for

general all temperature use. Other viscosities may be required

in other climates.

• Use only a (NGK) BR-6HS (PT4900), or (NGK) BP6ES / BPR6E

spark plug (PT6900/PT8900/PT12000). Gap the plug to 0.028

to 0.031 In. (0.7 to 0.8 mm) Always use a spark plug wrench.

Daily

1. Check engine oil level, and ll as necessary.

2. Check gasoline level, and ll as necessary.

Always follow the fueling procedure outlined earlier

in this manual.

First 20 Hours

1. Change engine oil.

Every 100 Hours

1. Change engine oil.

2. Clean the sediment cup.

3. Clean and re-gap the spark plug.

4. Clean the spark arrestor.

Weekly

1. Remove the air lter cover and clean the element. In very

dusty environments, check the lter daily. Replace the

element as needed. Replacement elements can be purchased

from your local engine manufacturer dealer.

Engine Operation and Service

1. Clean and oil air lter pad on gasoline engine every 25 hours

or once weekly. Do not permit the air intake screen around

the y wheel of the gas engine to load up with paint or

trash. Clean it regularly. The service life and eciency of

the gas engine model depends upon keeping the gasoline

engine running properly. Change the oil in the engine

every 100 hours. Failure to observe this may result in engine

overheating. Consult the engine manufacturer’s service

manual provided.

2. To conserve fuel, service life, and eciency of the sprayer,

always operate the gasoline engine at the lowest RPM at

which it runs smoothly without laboring and delivers the

amount required for the particular painting operation.

Higher RPM does not produce higher working pressure. The

gasoline engine is connected to the hydraulic pump by a

pulley combination designed to produce full paint delivery at

maximum RPM.

3. The warranty on gasoline engines or electric motors is limited

to the original manufacturer.

18 PowrTwin Plus

GB

Troubleshooting

Problem

A. Spitting gun

B. Gun will not shut o

C. Gun does not spray

Problem

A. Pump delivers on upstroke only

or goes up slowly and down fast

(commonly called downstroke

dive)

B. Pump delivers on down stroke

only or goes up fast and down

slowly

C. Pump moves up and down fast,

delivering material

D. Pump moves up and down

slowly when spray gun is shut

o

E. Not enough uid pressure at

gun

F. Pump chatters on up or down

stroke

Cause

1. Air in system

2. Dirty gun

3. Needle assembly out of adjustment

4. Broken or chipped seat

1. Worn or broken needle & seat

2. Needle assembly out of adjustment

3. Dirty gun

1. No paint

2. Plugged lter or tip

3. Broken needle in gun

Cause

1. Lower foot valve ball is not seating due to

trash or wear

2. Material too viscous to siphon.

3. Air leaking in on siphon side or damaged

siphon hose. Siphon may be too small for

heavy material.

1. Upper ball is not seating due to trash or wear

2. Lower packing set is worn

1. Material container is empty or material is too

thick to ow through siphon hose

2. Bottom ball stuck to foot valve seat

3. Siphon hose is kinked or loose

1. Loose connections. Bleed valve is open

partially or bleed valve is worn. Lower

packing seat is worn.

2. Upper and/or lower ball not seating

1. Spray tip is worn

2. Outlet lter or gun lter is clogged

3. Low voltage and/or inadequate amperage

4. Hose size or length is too small or too long

1. Solvent has caused upper packing to swell

Solution

1. Inspect connections for air leaks.

2. Disassemble and clean.

3. Inspect and adjust.

4. Inspect and replace.

1. Replace.

2. Adjust.

3. Clean.

1. Check uid supply.

2. Clean.

3. Replace.

Solution

1* Remove foot valve assembly. Clean and inspect. Test

foot valve by lling with water; if ball fails to seal the

seat, replace ball.

2. Thin material — contact manufacturer for proper

thinning procedures.

3. Tighten all connections between pump and paint

container. If damaged, replace. Switch to larger diameter

siphon set.

1* Check upper seat and ball with water. If ball fails to seal,

replace seat.

2* Replace packing set if worn.

1. Rell with new material. If too thick, remove siphon

hose, immerse uid section in material, and start pump

to prime. Add thinner to material. Change to bigger

siphon set. Open bleed valve to remove air and restart

pump.

2* Remove foot valve. Clean ball and seat.

3. Straighten.

1. Check all connections between pump and gun. Tighten

as necessary. If material is owing from bleed hose, close

bleed valve or replace, if necessary. Should none of the

above be evident, replace lower packing.

2* Reseat balls by cleaning.

1. Replace.

2. Clean or replace lter.

3. Check electrical service. Correct as required.

4. Increase hose size to minimize pressure drop through

hose and/or reduce hose length.

1* Replace packing.

7. Troubleshooting

7.1 Airless Gun

7.2 Fluid Section

* Refer to the Service Manual (part number 2439109, available online) for complete instructions regarding this procedure.

La page charge ...

Titan PowrTwin 4900 | 6900 | 8900 | 12000 Plus Operation Manuel utilisateur

Ce manuel convient également à

Titan PowrTwin 4900 | 6900 | 8900 | 12000 Plus Operation Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents