Audiovox UV7 Manuel utilisateur

UV7

Instruction Manual

Manual de Instrucciones

Guide d'instructions

i

Thank you for choosing a Phase Linear product. We hope you will find the instructions in this

owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll

learn how to use all the features of your new Phase Linear UV7 Mobile Multimedia AM/FM/

DVD Receiver for maximum enjoyment.

Preparation.......................................................................................................... 1

Features........................................................................................................................ 1

Tools and Supplies........................................................................................................ 1

Optional Accessories .................................................................................................... 1

Disconnecting the Battery............................................................................................. 2

Installation........................................................................................................... 5

Pre-installation .............................................................................................................. 5

Wiring............................................................................................................................ 5

Final Installation............................................................................................................ 5

Final ISO-DIN Installation.............................................................................................. 5

Controls and Indicators...................................................................................... 6

Button Operation........................................................................................................... 6

LCD Display/Indicators.................................................................................................. 8

Remote Control................................................................................................... 9

Using the TFT Monitor...................................................................................... 11

Open/Close TFT Monitor............................................................................................. 11

TFT Monitor Auto Open .............................................................................................. 11

Monitor Tilt Angle Adjustment..................................................................................... 11

Aspect Ratio................................................................................................................ 11

Image Setting.............................................................................................................. 11

Parking Brake.............................................................................................................. 11

Monitor Movement Mechanism................................................................................... 11

Operating Instructions ..................................................................................... 12

Power On / Off ............................................................................................................ 12

Audible Beep Confirmation ......................................................................................... 12

Mute............................................................................................................................ 12

Playing Source Selection............................................................................................ 12

Volume Adjustment..................................................................................................... 12

Audio Control Menu .................................................................................................... 12

System Reset.............................................................................................................. 12

Line Mute .................................................................................................................... 12

System Setup Menu.......................................................................................... 13

General Setup Menu................................................................................................... 13

ASP (Audio Sound Processing) Config Menu............................................................. 14

Exiting the System Setup Menu.................................................................................. 14

AM/FM Tuner Operation................................................................................... 15

Tuner TFT Display ...................................................................................................... 15

Tuner LCD Display...................................................................................................... 15

Switch to Radio Tuner source..................................................................................... 15

Select FM/AM Band.................................................................................................... 15

Seek Tuning................................................................................................................ 15

Manual Tuning ............................................................................................................ 15

Using Preset Stations.................................................................................................. 15

Auto Store (AS)........................................................................................................... 15

Local Radio Station Seeking (LOC)............................................................................ 15

DVD/VCD Video Operation............................................................................... 16

Opening/Closing the TFT Video Screen ..................................................................... 16

DVD LCD Display........................................................................................................ 16

Inserting a Disc ........................................................................................................... 16

Ejecting a Disc ........................................................................................................... 16

Reset the Loading Mechanism................................................................................... 16

Controlling Playback .................................................................................................. 16

Accessing the DVD Menu.......................................................................................... 16

Moving Through Chapters.......................................................................................... 16

Goto Search............................................................................................................... 16

Direct Chapter / Track Selection ................................................................................ 17

Viewing an Alternate Picture Angle (DVD Only) ........................................................ 17

Zooming..................................................................................................................... 17

Multi-Language Discs (DVD Only)............................................................................. 17

PBC (Play back Control) (VCD Only)......................................................................... 17

Playback Information.................................................................................................. 17

General Disc Information ........................................................................................... 18

DVD/Disc Setup Menu...................................................................................... 19

Accessing the DVD Setup Screen ............................................................................. 19

LANGUAGE Menu..................................................................................................... 19

VIDEO Menu.............................................................................................................. 19

AUDIO Menu ............................................................................................................. 19

RATING (Parental Lock) Menu .................................................................................. 19

DVD/Disc Audio Operation.............................................................................. 21

Controlling Playback .................................................................................................. 21

MP3/WMA Operation................................................................................................. 21

iPod Operation.................................................................................................. 22

Accessing iPod Mode................................................................................................. 22

Controlling your iPod.................................................................................................. 22

XM

®

Radio Operation....................................................................................... 23

Accessing XM

®

Radio Mode...................................................................................... 23

Displaying the Identification (ID) Code....................................................................... 23

Selecting a Station..................................................................................................... 23

Preset Mode............................................................................................................... 23

Channel/Category Guide Mode.................................................................................. 23

Direct Tuning.............................................................................................................. 23

XM Setup Menu ......................................................................................................... 24

Troubleshooting............................................................................................... 25

Error Messages.......................................................................................................... 26

Care and Maintenance............................................................................................... 27

Specifications................................................................................................... 28

12 Month Limited Warranty ............................................................................. 28

CONTENTS

ii

CONTENIDO

Gracias por elegir los productos Phase Linear. Esperamos que encuentre en este manual

instrucciones claras y fáciles de seguir. Si se toma unos pocos minutos para leerlo, aprenderá

cómo utilizar todas las funciones de su nuevo radio Phase Linear para su máximo

entretenimiento.

Preparation........................................................................................................ 29

Características............................................................................................................ 29

Herramientas y Provisiones........................................................................................ 29

Accesorios Opcionales................................................................................................ 30

Desconexión de la Batería.......................................................................................... 30

Instalación......................................................................................................... 33

Preinstalación.............................................................................................................. 33

Cableado..................................................................................................................... 33

Instalación Final.......................................................................................................... 33

Instalación del ISO-DIN Final...................................................................................... 33

Controles e Indicadores................................................................................... 34

Botones de Operación ................................................................................................ 34

Pantalla LCD/Indicadores ........................................................................................... 36

Control Remoto................................................................................................. 37

Utilización del Monitor TFT.............................................................................. 39

Abrir/Cerrar el Monitor TFT......................................................................................... 39

Abrir Automáticamente el Monitor TFT....................................................................... 39

Ajuste de Ángulo de Inclinación del Monitor............................................................... 39

Proporción de la Imagen............................................................................................. 39

Freno de Mano............................................................................................................ 39

Mecanismo de Movimiento de Monitor ....................................................................... 39

Instrucciones de Operación............................................................................. 40

Encendido / Apagado.................................................................................................. 40

Confirmación Bip Audible............................................................................................ 40

Mute............................................................................................................................ 40

Selección de Fuente de Reproducción....................................................................... 40

Ajuste de Volumen...................................................................................................... 40

Menú de Control de Audio .......................................................................................... 40

Reinicio del Sistema.................................................................................................... 40

Enmudecedor de Línea............................................................................................... 40

Menú de Configuración de Sistema................................................................ 41

Menú de Configuración General................................................................................. 41

Poniendo en Hora el Reloj.......................................................................................... 42

Menú de Configuración de ASP.................................................................................. 42

Saliendo del Menú de Configuración de Sistema....................................................... 42

Operación del Radio......................................................................................... 43

Pantalla del Sintonizador de TFT................................................................................ 43

Pantalla LCD del Radio............................................................................................... 43

Cambio a Fuente de Radio......................................................................................... 43

Selección de Banda FM/AM........................................................................................ 43

Búsqueda de Sintonía................................................................................................. 43

Sintonía Manual.......................................................................................................... 43

Utilizando Estaciones Configuradas Previamente...................................................... 43

Almacenamiento Automático (AS).............................................................................. 43

Buscador de Estaciones de Radio Local (LOC).......................................................... 43

Operación del Video de DVD/VCD................................................................... 44

Abriendo / Cerrando la Pantalla de Video TFT........................................................... 44

Pantalla LCD del DVD................................................................................................. 44

Insertar un Disco........................................................................................................ 44

Eyectar un Disco........................................................................................................ 44

Reinicie el Mecanismo de Carga ............................................................................... 44

Controlando la Reproducción..................................................................................... 44

Accediendo al Menú DVD.......................................................................................... 44

Moviéndose a Través de Capítulos............................................................................ 44

Búsqueda Goto.......................................................................................................... 45

Capítulo Directo / Selección de Pista......................................................................... 45

Viendo un Ángulo de Imagen Alterno (DVD Solamente) ........................................... 45

Zoom (Acercamiento de imagen)............................................................................... 45

Discos con Lenguaje Múltiple (DVD Solamente)....................................................... 45

PBC (Control de Reproducción) (VCD Solamente) ................................................... 45

Información de Reproducción .................................................................................... 45

Información de Disco General.................................................................................... 46

Menú de Configuración del DVD/DISCO ........................................................ 47

Accediendo a la Pantalla de Configuración de DVD.................................................. 47

Menú LANGUAGE (Lenguaje)................................................................................... 47

Menú VIDEO.............................................................................................................. 47

Menú de AUDIO......................................................................................................... 47

Menú RATING (Bloqueo de Padres).......................................................................... 47

Operación del Audio de DVD/Disco................................................................ 49

Controlando la Reproducción..................................................................................... 49

Operación MP3/WMA ................................................................................................ 49

Operación de iPod............................................................................................ 50

Al Modo del iPod del Acceso ..................................................................................... 50

Controlar su iPod ....................................................................................................... 50

Operation de la Radio XM

®................................................................................................... 51

Accessing XM

®

Radio Mode...................................................................................... 51

Exhibir el Código de la Identificación ......................................................................... 51

Selecting a Station..................................................................................................... 51

Preselección de Memoria Automática........................................................................ 51

Modo de la Guía del Canal/Categoría........................................................................ 51

Seleccione Directamente una Estación ..................................................................... 52

XM Menú Setup ......................................................................................................... 52

Solución de Problemas.................................................................................... 53

Mensajes de Error...................................................................................................... 54

Cuidado y Mantenimiento .......................................................................................... 55

Especificaciones.............................................................................................. 56

Garantia Limitade de 12 Meses....................................................................... 56

iii

TABLE DES MATIÈRES

Merci d'avoir choisi un produit Phase Linear. Nous espérons que vous allez trouver les

instructions dans ce guide de propriétaire claires et faciles à suivre. Prenez quelques minutes

à le consulter, vous apprendrez à utiliser toutes les fonctions de votre nouvelle radio Phase

Linear pour en tirer une jouissance maximum.

Preparatifs......................................................................................................... 57

Fonctions..................................................................................................................... 57

Outils et matériel......................................................................................................... 57

Accessoires facultatifs................................................................................................. 58

Débranchez la pile ...................................................................................................... 58

Installation......................................................................................................... 61

Pré-installation ............................................................................................................ 61

Câblage....................................................................................................................... 61

Installation finale ......................................................................................................... 61

Installation finale ISO-DIN........................................................................................... 61

Controles et indicateurs................................................................................... 62

Opération par bouton.................................................................................................. 62

Affichage/indicateurs LCD........................................................................................... 64

Telecommande.................................................................................................. 65

Utilisation de moniteur TFT ............................................................................. 67

Ouvrir/fermer le moniteur TFT..................................................................................... 67

Ouverture automatique du moniteur TFT.................................................................... 67

Ajustement d'angle d'inclination du moniteur.............................................................. 67

Rapport largeur/longueur............................................................................................ 67

Réglage d'image......................................................................................................... 67

Freins de stationnement.............................................................................................. 67

Mécanisme du mouvement du moniteur..................................................................... 67

Instructions d'operation................................................................................... 68

Puissance en marche/en arrêt.................................................................................... 68

Confirmation du bip sonore......................................................................................... 68

Muet............................................................................................................................ 68

Sélection de la source de reproduction....................................................................... 68

Ajustement du volume................................................................................................. 68

Menu contrôle d'audio................................................................................................. 68

Réinitialisation du système.......................................................................................... 68

Muet de ligne............................................................................................................... 68

Menu configuration systeme........................................................................... 69

Menu configuration générale....................................................................................... 69

Ajuster l'horloge .......................................................................................................... 70

Menu configuration ASP (traitement de son audio) .................................................... 70

Sortir du menu configuration système......................................................................... 70

Operation tuner AM/FM.................................................................................... 71

Affichage tuner TFT .................................................................................................... 71

Affichage aux cristaux liquides tuner........................................................................... 71

Changer à la source tuner radio.................................................................................. 71

Sélectionner la bande AM/FM..................................................................................... 71

Rechercher la syntonisation........................................................................................ 71

Syntonisation à la main............................................................................................... 71

Utilisation des stations pré-réglées............................................................................. 71

Auto stockage (AS)..................................................................................................... 71

Recherche station de radio locale (LOC).................................................................... 71

Operation video DVD/VCD ............................................................................... 72

Ouvrir/Fermer l'écran vidéo TFT................................................................................. 72

Affichage aux cristaux liquides DVD........................................................................... 72

Insérer un disque ....................................................................................................... 72

Ejection d'un disque................................................................................................... 72

Réinitialiser le mécanisme de chargement ................................................................ 72

Contrôler la reproduction............................................................................................ 72

Accéder au menu DVD .............................................................................................. 72

Se déplacer à travers les chapitres............................................................................ 73

Recherche allez à (GOTO) ........................................................................................ 73

Chapitre direct/sélection de piste............................................................................... 73

Visionner un angle de l'image alternatif (seulement DVD)......................................... 73

Zoom.......................................................................................................................... 73

Disques multi-langues (Seulement DVD)................................................................... 73

PBC (Contrôle de la reproduction) (Seulement VCD)................................................ 73

Information de la reproduction ................................................................................... 73

Information générale du disque.................................................................................. 74

Menu de configuration DVD/disque................................................................ 75

Accéder à l'écran configuration du DVD .................................................................... 75

Menu LANGUAGE..................................................................................................... 75

Fonction menu video.................................................................................................. 75

Menu audio ................................................................................................................ 75

Menu classement (verrouille parental)....................................................................... 75

Operation audio DVD/DisQUE......................................................................... 77

Contrôler la reproduction............................................................................................ 77

Opération MP3/WMA................................................................................................. 77

Operation iPod.................................................................................................. 78

Accéder à la mode iPod............................................................................................. 78

Contrôler votre iPod................................................................................................... 78

Operation radio XM

®................................................................................................................ 79

Accéder à la mode radio XM

®........................................................................................................... 79

Affichage du code d'identification............................................................................... 79

Sélectionner une station............................................................................................. 79

Mode de pré-réglage.................................................................................................. 79

Mode de guide chaîne / catégorie.............................................................................. 79

Syntonisation directe.................................................................................................. 80

Menu configuration XM.............................................................................................. 80

Depannage........................................................................................................ 81

Messages d'erreur...................................................................................................... 82

Soin et Entretien......................................................................................................... 83

Specifications................................................................................................... 84

Garantie limitée de 12 Mois.............................................................................. 84

iv

1

UV7

PREPARATION

Congratulations on your purchase of the Phase Linear UV7

Mobile Multimedia Receiver.

It’s a good idea to read all of the instructions before beginning

the installation. We recommend having your Phase Linear

UV7 installed by a reputable installation shop.

Features

DVD

• Compatible formats: DVD-R, DVD-RW, DVD+R,

DVD+RW, CD-R, CD-RW, CD-DA, MP3, WMA, SVCD,

VCD and MPEG1, MPEG2 and JPEG

• Region 1 playback

• 16:9 Aspect ratio - Normal / Cinema

• Front panel DVD control

• High-speed Fast Forward / Fast Rewind 2X, 4X, 8X, 32X

• Play, Pause, Stop, Slow

• Chapter Up / Down

• Wolfson Microelectronics high performance 24-bit, 192

kHz DAC supports 2-channel "Down-Mix” audio modes

• 16Mbit high-speed flash memory - 80nS access time

MP3/WMA

• GIGA MP3 - Store up to 999 MP3 files on a DVD

• ID3-tag compatible

• Direct track access

• Play, Pause, Stop, Track Up / Down

• 100 second (MP3), 200 second (WMA) ESP - Electronic

Skip Protection

CD

• CD-text compatible

• 4 second ESP - Electronic Skip Protection

AM/FM Tuner

• US/Euro/Latin/Asia Tuner

• 30 Station presets (18FM/12AM)

• JENSEN Plus Tuner II

Outboard Media Module

• XM Radio and iPod

XM Ready

• Requires Optional Terk XMD1000 Tuner Box

• Requires Optional Terk XMDJEN100 or Jensen JXMC XM

Cables

• Advanced display shows the artist, song title, and XM

channel and category at a glance

• Direct Channel entry

Made for iPod

• Controls and charges all iPod's except "Shuffle"

• Displays all text information including category, track

name, artist and channel number

Chassis

• 7-inch TFT active-matrix LCD, 336, 960 pixels (1440W X

234H)

• Full automatic motorized TFT LCD flip-out and up

• 16-step TFT LCD tilt adjustment

• Beep Tone confirmation

• Heat management system - Incorporates forced air-

cooling to keep the chip-sets operating at nominal

temperatures

• Heavy duty galvanized chassis

General

• Full function infrared remote control

• 1 NTSC composite video output for additional screens

• OSD- On Screen Display menu control

• High performance audio processor

• Electronic volume, bass, treble, balance and fader

• Bass center frequency adjustment - 60, 80, 100, 130,

150 and 200Hz

• Bass Q factor - 1.0, 1.25, 1.5 and 2.0

• Treble center frequency adjustment - 10, 12.5, 15 and

17kHz

• Subwoofer crossover - 80, 120 and 160Hz

• Subwoofer Phase - 0, 180 degrees

• Subwoofer level - variable

• 100-ohm low impedance preamp outputs - all channels

• 5V Peak / 2V RMS RCA outputs - all channels

• 1-pair Front RCA outputs

• 1-pair Rear RCA outputs

• Single Subwoofer RCA output

• 1-pair Auxiliary RCA A/V inputs

• Flex fader

• Front panel (when screen is closed) high contrast LCD

• Rotary encoder audio control

• Joystick menu navigation

Tools and Supplies

You will need these tools and supplies to install your UV7:

• Torx type, flat-head and Philips screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screwdriver, socket wrench

set or other tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

WARNING! Only connect the unit to a12-volt power

supply with proper grounding.

WARNING! Never install this unit where operation and

viewing could interfere with safe driving conditions.

WARNING! To reduce the risk of a traffic accident (except

when using for rear view video camera) never use the

video display function while driving the vehicle. This is a

violation of federal law.

WARNING! Never disassemble or adjust the unit.

WARNING! To prevent injury from shock or fire, never

expose this unit to moisture or water.

WARNING! Never use irregular discs.

WARNING! To prevent damage to the mechanism inside

this unit, avoid impact to the TFT monitor.

WARNING! Using an improper fuse may cause damage

to the unit and result in a fire.

WARNING! To prevent damage to the screen, avoid

touching it with your fingers or other objects.

WARNING! The monitor employs an automatic motorized

mechanism. To prevent damage to the core mechanism,

please do not push, pull or swivel the monitor manually.

Optional Accessories

iAUX

3

READY (Sold Separately)

• Can connect to any portable media device or multimedia

device using a standard 3.5mm plug.

• Converts 3.5mm auxiliary input to RCA stereo outputs for

easy connection to the radio’s auxiliary inputs.

2

UV7

Disconnecting the Battery

To prevent a short circuit, be sure to turn off the ignition and

remove the negative (-) battery cable prior to installation.

NOTE: If the UV7 is to be installed in a car equipped with

an on-board drive or navigation computer, do not

disconnect the battery cable. If the cable is

disconnected, the computer memory may be lost. Under

these conditions, use extra caution during installation to

avoid causing a short circuit.

3

UV7

WIRING DIAGRAM

4

UV7

WIRING DIAGRAM - MULTIMEDIA CONNECTIONS

*TERK XMDJEN100 cables (sold separately)

**TERK XMD1000 Direct Tuner and antenna (sold

separately)

5

UV7

INSTALLATION

Pre-installation

1. Press the metal levers on both sides to remove the half-

sleeve from the radio.

2. Install the half-sleeve.

a. Install adaptor if necessary (optional).

b. Install half-sleeve into adaptor or dashboard (only use

the supplied screws). Do not force the sleeve into the

opening or cause it to bend or bow.

c. Locate the series of bend tabs along the top, bottom

and sides of the mounting sleeve. With the sleeve fully

inserted into the dashboard opening, bend as many of

the tabs outward as necessary so that the sleeve is

firmly secured to the dashboard.

d. Install support strap to make the unit more stable.

CAUTION! Be careful not to damage the car wiring.

3. Place the radio in front of the dashboard opening so the

wiring can be brought through the mounting sleeve.

Wiring

Complete wiring as illustrated in the wiring diagrams on

pages 3 and 4. Once the wiring is complete, reconnect the

battery negative terminal. If there is no ACC available,

connect the ACC lead to the power supply with a switch.

NOTE: When replacing a fuse, be sure to use correct

type and amperage to avoid damaging the radio. The

UV7 uses one 15 amp mini-ATM fuse, located in the black

filter box in-line with the main wire harness.

Final Installation

After completing the wiring connections, turn the unit on to

confirm operation (ignition switch must be on). If unit does not

operate, recheck all wiring until problem is corrected. Once

proper operation is achieved, turn off the ignition switch and

proceed with final mounting of the chassis.

1. Connect wiring adaptor to existing wiring harness.

2. Connect antenna lead.

3. Carefully slide the radio into the half-sleeve making sure

it is right-side-up until it is fully seated and the spring

clips lock it into place.

NOTE: For proper operation of the CD/DVD player, the

chassis must be mounted within 20° of horizontal. Make

sure the unit is mounted within this limitation.

4. Attach one end of the perforated support strap

(supplied) to the screw stud on the rear of the chassis

using the hex nut provided. Fasten the other end of the

perforated strap to a secure part of the dashboard either

above or below the radio using the screw and hex nut

provided. Bend the strap to position it as necessary.

CAUTION! The rear of the radio must be supported with

the perforated strap to prevent damage to the dashboard

from the weight of the radio or improper operation due to

vibration.

5. Replace any items you removed from the dashboard.

Final ISO-DIN Installation

1. Remove trim ring.

2. Mount factory brackets on new radio using existing

screws from old radio.

3. Slide radio chassis into dash opening and secure.

4. Reinstall dash panel.

PREPARE RADIO

INSTALL HALF SLEEVE

FINAL INSTALLATION

FINAL ISO-DIN INSTALLATION

6

UV7

CONTROLS AND INDICATORS

Button Operation

1. OPEN

Press the OPEN button (1) to activate the automatic

mechanical system and move the TFT monitor into viewing

position. Press again to close the TFT.

2. WIDE/PICTURE

Press the WIDE/PICTURE button (2) to adjust the display

aspect of the picture to one of three settings: Cinema, Full or

Normal. Press and hold to access picture settings.

3. ( )

Press the button (3) to adjust the upward tilt angle of the

screen one step at a time. Press and hold this button to

continuously adjust the upward tilt or picture settings.

4. ( )

Press the button (4) to adjust the downward tilt angle of the

screen one step at a time. Press and hold this button to

continuously adjust the downward tilt or picture settings.

5. DISP

Press the DISP button (5) to display system information on

the screen.

6. VOL/LOC/DX

Rotate the VOL/LOC/DX knob (6) to adjust the volume.

Press and release to enter and/or confirm audio settings.

Press and hold to activate the Local (LOC) setting.

7. POWER/MUTE

Press the POWER/MUTE button (7) once to turn the unit on.

Press again to mute the volume. Press and hold to turn the

unit off.

NOTE: The UV7 features Softmute, which will allow the

volume to increase or decrease gradually when the

MUTE function is activated or deactivated.

8. 1/AUDIO

DVD Mode: Press to select audio language during playback.

TUNER Mode: Press once to play preset radio station

channel 1. Press and hold to store the current radio station in

preset channel 1.

9. 2/SUBTITLE

DVD Mode: Press once to select the subtitle language during

playback.

TUNER Mode: Press once to play preset radio station

channel 2. Press and hold to store the current radio station in

preset channel 2.

7

UV7

CONTROLS AND INDICATORS

10. 3/SCN

DVD Mode: Press once to start scan playback.

TUNER Mode: Press once to play preset radio station

channel 3. Press and hold to store the current radio station in

preset channel 3.

11. 4/REP

DVD Mode: Press once to start repeat playback.

TUNER Mode: Press once to play preset radio station

channel 4. Press and hold to store the current radio station in

preset channel 4.

12. 5/RDM

DVD Mode: Press once for random playback.

TUNER Mode: Press once to play preset radio station

channel 5. Press and hold to store the current radio station in

preset channel 5.

13. 6/STOP

DVD Mode: Press once to stop playback.

TUNER Mode: Press once to play preset radio station

channel 6. Press and hold to store the current radio station in

preset channel 6.

14. BAND

TUNER Mode: Press to switch between FM and AM.

15. SRC

Press once to select playing mode.

16. ( )

DVD Mode: Press once to play back previous chapter/track.

TUNER Mode: Press once to auto search for the previous

available radio station.

MENU Mode: Press once to move the cursor to the left.

17. ( )

DVD Mode: Press once to enter the next chapter or track.

TUNER Mode: Press once to auto-search the next available

radio station.

MENU Mode: Press once to move the cursor to the right.

18. ( )

DVD Mode: Press once for fast forward.

TUNER Mode: Press to go up one frequency step.

MENU Mode: Press once to move the cursor up.

19. ( )

DVD Mode: Press once for slow forward.

TUNER Mode: Press to go down one frequency step.

MENU Mode: Press once to move the cursor down.

20. PLAY/ENTER

DVD Mode: Press once to start a playback.

Press once to confirm a selection.

21. ( )

Press once for disc insertion/ejection.

Press and hold to reset core mechanism position.

22. RESET

Press to reset system settings to factory default (except the

password and parental lock setting).

23. LCD Display

24. TFT Display

25. IR Remote Control Receiver

26. AS (Auto Store)

Press to auto store strong radio stations in the six preset

channels in the current band.

8

UV7

CONTROLS AND INDICATORS

LCD Display/Indicators

1. Disc Indicator

Illuminated when disc is loaded

2. DVD Playback Indicators (SCN/RPT/RDM/ALL)

The following DVD playback indicators become Illuminated

when the corresponding function is active:

• SCN: scan playback

• RPT: repeat playback

• RDM: random playback

• ALL: playback all chapters

3. Loudness Indicator (LOUD)

The loudness indicator becomes illuminated when the LOUD

function is activated.

4. Main Display

The main display is an 8 digit, 14 segment LCD which

displays the time, tuning frequency and other text

information.

5. Channel/Disc Display

The channel/disc display is a 2 digit, 7 segment LCD display

which displays the disc number or radio channel indicators

when the corresponding function is active:

• CH: radio is activated

• DISC: DVD/CD mode is activated

6. Stereo/Local Indicator

The stereo/local indicator illuminates one of the following

indicators when the corresponding function is active:

• ST: radio is in stereo mode

• LOC: local radio station seeking function is activated

1 2 3 4 5 6

9

UV7

REMOTE CONTROL

Table 1: Remote Control Functions

Button Function

Name/Ref # DVD VCD AM/FM CD/MP3 XM iPod

MENU 1 Enters the main

menu of the disc

Turns on PBC

when playing VCD

Displays XM

Setup Menu

Selects Photo

mode

TITLE 2 Enters the title

menu of the disc

Plays first ten sec-

onds of each

chapter/title

Selects Music

mode

MUTE 3 Toggles on/off

audio output

Toggles on/off

audio output

Toggles on/off

audio output

Toggles on/off

audio output

Toggles on/off

audio output

Toggles on/off

audio output

POWER

4 Turns the power

on/off

Turns the power

on/off

Turns the power

on/off

Turns the power

on/off

Turns the power

on/off

Turns the power

on/off

AUDIO 5 Changes the

audio language

for disc playback

Selects Video

mode

REPT A-B 6 Setup to repeat

playback from

time frame A to

time frame B

Setup to repeat

playback from

time frame A to

time frame B

REPT 7 Repeats playback

of current chapter

Repeats playback

of current chapter

Repeats playback

of current track

Selects Category

Mode

Repeats playback

of current track

SRC 8 Selects playing

mode

Selects playing

mode

Selects playing

mode

Selects playing

mode

Selects playing

mode

Selects playing

mode

SUBTITLE 9 Language selec-

tion for subtitle

DISP 10 Displays playing

information

Displays playing

information

Displays playing

information

Display playing

information

Displays playing

information

Display playing

information

ANGLE 13 Plays back disc in

different angle for

a scene

Plays back Picture

CD with different

angle of picture

displayed

14 Fast forwards the

disc content

Fast forwards the

disc content

Fast forwards the

disc content

Accesses iPod

Menu

VOL - 15 Decreases vol-

ume

Decreases vol-

ume

Decreases vol-

ume

Decreases vol-

ume

Decreases vol-

ume

Decreases vol-

ume

VOL + 16 Increases volume Increases volume Increases volume Increases volume Increases volume Increases volume

17 Selects the previ-

ous chapter for

playback

Selects the previ-

ous chapter for

playback

Searches an

available radio

station by

decreasing tuning

frequency

Selects the previ-

ous track for play-

back

Searches an

available radio

station by

decreasing tuning

frequency

Pauses playback/

starts playback

18 Pauses playback/

starts playback

Pauses playback/

starts playback

Scans FM/AM

radio station;

plays/stores radio

station; deletes

radio station

Pauses playback/

starts playback

Scans XM radio

station; plays/

stores radio sta-

tion; deletes radio

station

NOTE: Your remote control may differ slightly

from the one pictured here. The above diagram is

for illustrative purposes only.

10

UV7

19 Selects the next

chapter for play-

back

Selects the next

chapter for play-

back

Searches an

available radio

station by increas-

ing tuning fre-

quency

Selects the next

track for playback

Searches an

available radio

station by increas-

ing tuning fre-

quency

Selects the next

track for playback

BAND 20 Stops playback Stops playback Selects FM/AM

band

Stops playback Selects XM, XM1,

XM2, or XM3

band

GOTO 21 Goes to specific

time frame and

playback

Goes to specific

time frame and

playback

22 Slow Playback/

Rewinds playback

Slow Playback/

Rewinds playback

ZOOM 23 Zooms in/out on

an image

Zooms in/out on

an image

PIC 24 Displays set-up

parameters

Displays set-up

parameters

OPEN/

CLOSE

25 Opens/Closes the

TFT monitor

Opens/Closes the

TFT monitor

Opens/Closes the

TFT monitor

Opens/Closes the

TFT monitor

Opens/Closes the

TFT monitor

Opens/Closes the

TFT monitor

26 Decreases moni-

tor tilt angle

Decreases moni-

tor tilt angle

Decreases moni-

tor tilt angle

Decreases moni-

tor tilt angle

Decreases moni-

tor tilt angle

Decreases moni-

tor tilt angle

27 Increases monitor

tilt angle

Increases monitor

tilt angle

Increases monitor

tilt angle

Increases monitor

tilt angle

Increases monitor

tilt angle

Increases monitor

tilt angle

WIDE 28 (For DVD, SD

card with Video,

Camera, and AUX

IN) Selects dis-

play mode: CIN-

EMA, NORMAL or

OFF

Selects display

mode: CINEMA,

NORMAL or OFF

Selects display

mode: CINEMA or

OFF

Selects display

mode: CINEMA,

NORMAL or OFF

Selects display

mode: CINEMA or

OFF

Selects display

mode: CINEMA or

OFF

0, 1, 2, 3, 4,

5, 6, 7, 8, 9,

0 (Numeric

Keypad)

29 Directly accesses

chapter

1-6 selects preset

for current band

Directly accesses

track

1-6 selects preset

for current band

DVD

SETUP

30 Displays DVD

Setup menu

Displays DVD

Setup menu

Displays DVD

Setup menu

Displays DVD

Setup menu

Displays DVD

Setup menu

Displays DVD

Setup menu

SYS

SETUP

31 Displays System

Setup menu

Displays System

Setup menu

Displays System

Setup menu

Displays System

Setup menu

Displays System

Setup menu

Displays System

Setup menu

SCAN 34 Plays the first ten

seconds of each

track

EJECT 35 Ejects disc Ejects disc Ejects disc Ejects disc Ejects disc Ejects disc

Table 1: Remote Control Functions

Button Function

Name/Ref # DVD VCD AM/FM CD/MP3 XM iPod

NOTE: Your remote control may differ slightly

from the one pictured here. The above diagram is

for illustrative purposes only.

11

UV7

USING THE TFT MONITOR

Open/Close TFT Monitor

Press the OPEN button (1) on the front panel or press the

( ) button (25) of the front zone remote control to activate

the mechanism that moves the display panel into the viewing

position.

Press the OPEN button (1) on the front panel or press the

( ) button (25) of the front zone remote control to load the

display panel back into the compartment.

TFT Monitor Auto Open

If “TFT Auto Open” is “on” when the unit is turned on, the

monitor automatically moves to the viewing position.

If “TFT Auto Open” is ”off” when the unit is turned on, press

the OPEN button (1) or ( ) button (25) on the front zone

remote control to move the monitor into the viewing position.

If “TFT Auto Open” is set to ”Manual”, the TFT will not close

when the key is turned off.

Monitor Tilt Angle Adjustment

A known characteristic of LCD panels is the quality of the

display in relationship to the viewing angle. The monitor

angle can be adjusted for optimum viewing using one of the

following methods:

Step by Step Angle Adjustment

Press the ( ) or ( ) button (3, 4) on the monitor frame to

adjust the tilt angle of the screen one step at a time.

Continuous Angle Adjustment

Press and hold the ( ) or ( ) button (3, 4) on the monitor

frame to adjust the tilt angle in a continuous motion.

Aspect Ratio

Press the WIDE button (28) on the remote control or WIDE/

PICTURE button (2) on the monitor to adjust the aspect ratio

as follows:

Image Setting

Table 2 shows the video output mode for each playing

source.

*CVBS – Composite Video Baseband Signal

Parameter Adjustment Procedure

1. Enter Picture Quality Setting mode:

Press the PIC button (24) on the remote or press and

hold the WIDE/PICTURE button (2) on the monitor

panel.

2. Select Item to Set:

Press the (>>) (

<<) buttons (14, 22) on the remote or

press and hold the (/\) or (V) buttons (18, 19) on the

monitor panel.

3. Set Parameters:

Press (|<<) (>>|) buttons (17, 19) on the remote or press

(<) (>) buttons (16, 17) on the monitor panel.

4. Exit Picture Quality Setting Mode:

Press the PIC button (24) on the remote or press and

hold the WIDE/PICTURE button (2) on the monitor

panel.

Parking Brake

Parking Brake Inhibit

When the pink "Parking" wire is connected to the vehicle

brake switch, the front TFT monitor will display video only

when the parking brake sequence is engaged. Before starting

the parking brake sequence, the radio must be on with the

video media disc inserted and playing.

Parking Brake Sequence

There are two situations that can start the Parking Brake

Sequence:

• Parking brake is engaged (on) when the vehicle is started

or the accessory / ignition is turned on. To activate video,

the following sequence of events must be completed:

a. Release parking brake for 1 second.

b. Reapply the parking brake.

c. Video should be displayed on the TFT monitor within 1

~ 2 seconds.

• Parking break is disengaged (off) when the vehicle is

started or the accessory / ignition is turned on. To activate

video, the following sequence of events must be

completed:

a. Set parking brake for 1 second.

b. Release parking brake for 1 second.

c. Reapply parking brake.

d. Video should be displayed on the TFT monitor within 1

~ 2 seconds.

Monitor Movement Mechanism

If an obstruction occurs in the monitor path, the following

protective measurements can be executed to prevent

damage to the mechanism or monitor:

After the protective procedure is executed, normal operation

is resumed by pressing the OPEN button (1) or disconnecting

and reconnecting the power.

CINEMA

The entire screen is extended

horizontally to the aspect ratio of 16 to

9. The extension ratio is the same at

any point.

NORMAL

The conventional display image has a

4 to 3 ratio of horizontal to vertical,

leaving a blank area on the right and

left sides of the display.

OFF

Table 2: Video Output Modes

Playing Source Video Output Modes

AM/FM TUNER YUV Mode

XM TUNER YUV Mode

iPod YUV Mode

DVD YUV Mode

AUX IN CVBS Mode

Table 3: Monitor Protective Measures

Obstruction

Self

Protection

OPEN Button

Pressed

Power

Reconnected

Monitor load-

ing out hori-

zontally

Monitor is auto-

matically

loaded into unit

Monitor fully

extended hori-

zontally

Monitor is auto-

matically

loaded into unit

Monitor load-

ing in hori-

zontally

Unit stops at

obstruction

point

Monitor fully

extended hori-

zontally

Monitor is auto-

matically

loaded into unit

Monitor load-

ing out verti-

cally

Unit stops at

obstruction

point

Monitor swiv-

els back to the

unit

Monitor swiv-

els back to the

unit

Monitor load-

ing in verti-

cally

Unit stops at

obstruction

point

Monitor swiv-

els back to the

unit

Monitor swiv-

els back to the

unit

12

UV7

OPERATING INSTRUCTIONS

Power On / Off

Press the /MUTE button (1) to turn the unit on. The buttons

on the front of the unit light up and “WELCOME” appears

briefly in the LCD panel (17), followed by the current mode

status. If the TFT screen is open, only the current mode

status is displayed.

Press and hold the /MUTE button (1) on the front panel or

the POWER button (4) on the remote to power off the

unit.The monitor is drawn back into the main compartment

and the LCD screen displays “BYE-BYE”.

Audible Beep Confirmation

An audible beep tone confirms each function selection. The

beep tone cannot be disabled.

Mute

Press the /MUTE button (1) on the front panel or the MUTE

button (3) on the remote to mute the volume from the unit.

Press the MUTE button again to restore the volume. “MUTE”

is displayed on the LCD monitor. Adjusting the volume or

using any of the audio set-up features cancels the mute

function.

Playing Source Selection

Press the SRC button (15) on the front panel or the SRC

button (8) on the remote to change between available playing

sources in the following order: Tuner, DVD/CD, XM, iPod,

Aux In, Camera (rear view video camera) and TV. The

playing mode is displayed on the TFT and LCD screens.

AUX IN Mode

An external peripheral device can be connected to this unit

via standard RCA connectors for video and left/right audio.

Volume Adjustment

To increase or decrease the volume level, turn the ROTARY

ENCODER (6) on the front panel or press the VOL+/ VOL-

buttons (15, 16) on remote control. When the volume level

reaches “0” or “40”, a beep sounds, indicating that the

adjustment limit has been reached. The volume ranges from

“0” to “40”. The LCD or TFT screen displays the volume level

for 3 seconds.

Programmable Turn-On Volume

This feature allows the user to select a turn-on volume setting

regardless of the volume setting prior to turning the unit off.

To program a specific volume level, push and hold the

AUDIO button (2) while the yellow volume bar is displayed on

the screen. The unit will beep two times to confirm your turn-

on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your

audio system to meet the acoustical characteristics of your

vehicle, which vary depending on the type of vehicle and its

measurements. To get the best possible sound quality from

your new system, be sure to adjust the settings for the

speakers as well. Proper setting of the Fader and Balance

boosts the effects of the cabin equalizer.

Accessing the Audio Control Menu

Press the VOL/LOC/DX knob (6) on the front panel once to

display the “AUDIO” menu.

Selecting an Audio Feature for Adjustment

Continuously press the VOL/LOC/DX knob (6) on the front

panel, or press the (>>)/(

<<) buttons (14, 22) on the remote

control or the (/\)/(V) buttons (18, 19) on the joystick to select

the audio feature to be adjusted.

Adjusting an Audio Feature

Rotate the VOL/LOC/DX knob (6), press the (|<<)/(>>|)

buttons (17, 19) on the remote control, or press the (<)/(>)

buttons (16, 17) on the joystick to adjust the selected feature

to the desired setting.

NOTE: The Bass and Treble levels are only adjustable

when EQ is set to “User” mode.

Loudness

• The Loudness level/function is dependent on the main

volume setting. As the volume is increased, less

Loudness compensation is applied to the audio signal.

This is referred to "Auto-Loudness". The possible

loudness settings are as follows:

•Off

• 1 - Slight bass boost at low volume level

• 2 - Moderate bass boost at low volume level

• 3 - Good bass boost at low to mid volume level

• 4 - maximum bass boost at mid volume level

Exiting the Audio Control Menu

Press and hold the VOL/LOC/DX knob (6) or stop making

adjustments for a few seconds to exit the audio control menu.

System Reset

To correct a system halt or other illegal operation, use the tip

of a pen to press the RESET button (22) located on the front

bottom-right corner of the unit. After a system reset, the unit

restores all factory default settings.

NOTE: If the unit is reset while a DVD is playing, the DVD

resumes play once the reset is complete.

Line Mute

If the “MUTE” wire is connected, audio output mutes when a

telephone call is received by the car phone or when verbal

navigation is performed (external navigation input required).

Table 4: Audio Adjustments

Audio Function Adjustable Range

EQ User

Flat

Jazz

Pop

Classical

Rock

Vocal

Bass -14 to +14

Treble -14 to +14

Fader -7 to +7

Balance -9 to +9

Sub -9 to +9

Loud Off, 1-4

[RESET] Button

13

UV7

SYSTEM SETUP MENU

In “System Setup” mode, “ASP CONFIG” and “GENERAL

SETUP” are available for adjustment. Setup can be

performed by pressing the dedicated button on the remote

control or on the front panel. For system settings, press the

SYS SETUP button (31) on the remote control to enter the

“System Setup” menu. “ASP CONFIG” is highlighted in

green.

General Setup Menu

Accessing the General Setup Menu

To access the “GENERAL SETUP” Menu, press the direction

buttons on the joystick (16, 17, 18, 19) or remote control (14,

17, 18, 19, 22) to highlight “GENERAL SETUP” in green.

Press the >/|| button (18) on the remote control to enter the

“GENERAL SETUP” menu. A menu appears with the option

for the first item, “Radio”, highlighted in light blue.

Selecting a Feature for Adjustment

Press the >> or

<< buttons (14, 22) on the remote control or

the /\ or V buttons (18, 19) on the joystick to select the feature

to be adjusted.

Adjusting a Feature

1. Enter the option field for the feature you want to adjust

by pressing the >/|| button (18) on the remote or by

pressing the ENTER (joystick) button (20) on the unit. A

submenu appears in a second row with the selected

option highlighted in light blue.

2. Select a new value by pressing the >> or

<< buttons (14,

22) on the remote control or the /\ or V buttons (18, 19)

on the joystick.

3. Confirm your selection by pressing the

<<, |<<, or >>|

buttons (22, 17, 19) on the remote control, or the < or >

button (16, 17) on the joystick. The new value is

highlighted in light blue and setup is complete.

DIRECTION BUTTONS

Table 5: General Setup Menu Features

Setting Options Function

Radio USA • AM Frequency Spacing - 10kHz

• AM Frequency Band -

530kHz~1720kHz

• FM Frequency Spacing - 200kHz

• FM Frequency Band -

87.5MHz~107.9MHz

Europe • AM Frequency Spacing - 9kHz

• AM Frequency Band -

522kHz~1620kHz

• FM Frequency Spacing - 50kHz

• FM Frequency Band -

87.5MHz~108.0MHz

South

America 1

• AM Frequency Spacing - 10kHz

• AM Frequency Band -

530kHz~1720kHz

• FM Frequency Spacing - 100kHz

• FM Frequency Band -

87.5MHz~108.0MHz

South

America 2

• AM Frequency Spacing - 5kHz

• AM Frequency Band -

520kHz~1600kHz

• FM Frequency Spacing - 100kHz

• FM Frequency Band -

87.5MHz~108.0MHz

Arabia • AM Frequency Spacing - 9kHz

• AM Frequency Band -

531kHz~1620kHz

• FM Frequency Spacing - 100kHz

• FM Frequency Band -

87.5MHz~108.0MHz

Korea • AM Frequency Spacing - 9kHz

• AM Frequency Band -

531kHz~1602kHz

• FM Frequency Spacing - 200kHz

• FM Frequency Band -

88.1MHz~107.9MHz

China • AM Frequency Spacing - 9kHz

• AM Frequency Band -

522kHz~1620kHz

• FM Frequency Spacing - 100kHz

• FM Frequency Band -

87.5MHz~108.0MHz

Clock Mode 12H Clock displays 12 hour time using

AM and PM.

24H Clock displays 24 hour time up to

23:59.

Screen Saver On Turn screen saver on/off.

Off

Video Format

(Input cir-

cuitry auto-

detects the

video signal

from the

CAMERA

and Aux In

video source.

Video format

does not

affect the TV

tuner - this is

an NTSC TV

tuner only.

Auto The color signal output is switched

automatically based on the current

video input signal - NTSC or PAL.

NTSC The color signals are output in the

standard NTSC format.

PAL The color signals are output in the

standard PAL format.

TFT Auto

Open

On The TFT panel automatically opens

when the unit is turned on.

Off You must press the OPEN button

(1) to open the TFT panel.

Manual When the ignition is turned OFF, the

TFT panel DOES NOT retract if it

was previously out

OSD Lan-

guage

English The menus are displayed in English

only.

Clock (HH:MM) See “Adjusting the clock” to learn

how to set the clock.

Return to previous menu.

Table 5: General Setup Menu Features

Setting Options Function

14

UV7

Adjusting the Clock

Method 1 – TFT screen open:

1. Access the “Clock” setting under the General Setup

menu.

2. Press the >> or

<< buttons (14, 22) on the remote

control or the /\ or V buttons (18, 19) on the joystick to

move the cursor to the “Hour” or “Min” position.

3. Press the |<<, or >>| buttons (17, 19) on the remote

control or the < or > buttons (16, 17) on the joystick to

adjust the hour or minutes.

4. Press the

<< button (14) on the remote control to confirm

setup.

Method 2 – TFT screen closed:

1. Press and hold the DISP button (5) until the clock

flashes in the LCD display.

1. Press the /\ or V buttons (18, 19) on the joystick to move

the cursor to the “Hour” or “Min” position.

2. Press the < or > buttons (16, 17) on the joystick to adjust

the hour or minutes.

3. Press the DISP button (5) on the unit to confirm setup.

Returning to the System Setup Menu

To return to the System Setup menu, move to , then

press the >/|| button on the remote control.

ASP (Audio Sound Processing) Config

Menu

The ASP Config Menu allows you to make fine audio

adjustments.

Accessing the ASP Config Menu

To access the “ASP CONFIG” Menu, press the direction

buttons on the joystick (16, 17, 18, 19) or remote control (14,

17, 18, 19, 22) to highlight “ASP CONFIG” in green. Press

the >/|| button (18) on the remote control to enter the “ASP

CONFIG” menu. A menu appears with the option for the first

item, “Bass Center Freq”, highlighted in light blue.

Adjusting a Feature

1. Enter the option field for the feature you want to adjust

by pressing the >/|| button (18) on the remote or by

pressing the ENTER (joystick) button (20) on the unit. A

submenu appears in a second row with the selected

option highlighted in light blue.

2. Select a new value by pressing the >> or

<< buttons (14,

22) on the remote control or the /\ or V buttons (18, 19)

on the joystick.

3. Confirm your selection by pressing the

<<, |<<, or >>|

buttons (14, 17, 19) on the remote control, or the < or >

button (16, 17) on the joystick. The new value is

highlighted in light blue and setup is complete.

Exiting the System Setup Menu

To exit setup mode and resume normal playback, press the

SYS SETUP button (31) on the remote control or the DISP

button (5) on the front panel.

Table 6: ASP Config Menu Features

Setting Options Function

Bass Center

Freq

60Hz According to the audio source, select

the Bass Center Frequency to

achieve the best Bass effect.

80Hz

100Hz

130Hz

150Hz

200Hz

Treble Center

Freq

10KHz According to the audio source, select

the Treble Center Frequency to

achieve the best Treble effect.

12.5KHz

15KHz

17KHz

Sub Filter 80Hz Selecting a crossover frequency sets

a cut-off frequency of the subwoofer's

LPF (low-pass filter) and the

“SMALL” speakers' HPF (high-pass

filter). The Crossover frequency set-

ting has no effect if the subwoofer is

set to “OFF” and any other speaker is

set to “LARGE”.

120Hz

160Hz

Sub Phase 0D Subwoofer output IN phase

180D Subwoofer output OUT OF phase

NOTE: Depending on your installa-

tion, reversing the subwoofer phase

may increase Bass output.

Bass Q-Factor 1.0 When the Bass Center Frequency is

selected, adjusting the Bass Q-Fac-

tor alters the sharpness of the Bass

output.

1.25

1.5

2.0

Return to previous menu.

Table 6: ASP Config Menu Features

Setting Options Function

La page est en cours de chargement...

Audiovox UV7 Manuel utilisateur

Ce manuel convient également à

Audiovox UV7 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents