Majestic fireplaces Woodland UVLC24RP Installation And Operating Instructions Manual

Marque: Majestic fireplaces

Modèle: Woodland UVLC24RP

Taper: Installation And Operating Instructions Manual

Ce manuel convient également à

ATTENTION

Installation and service must be performed by

a qualiﬁed agency, individual, ﬁrm, corporation,

or company, experienced in the installation, re

pair, and servicing of this type of gas appliance.

Do not modify, alter or tamper with any part of

this heater, control, or logs.

— Do not store or use gasoline or other ﬂam-

mable vapors and liquids in the vicinity of this

or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

Installation and Operating

Instructions

W A R N I N G

If the information in this manual is not followed exactly, a ﬁre or explosion may result, causing property

damage, injury or loss of life.

Tested and listed to ANSI Z21.11.2b.2004, Unvented Heaters,

and Z21.60b-2004; CSA 2.26b-2004 Decorative Gas Appliances

for Installation in Solid-Fuel Burning Fireplaces.

W A R N I N G

CARBON MONOXIDE POISONING MAY LEAD TO DEATH.

When used without fresh air, vent-free log sets may give off carbon monoxide, an odorless, poisonous gas.

Some people - pregnant women, people with heart or lung disease, anemia, or persons under the inﬂuence of alcohol, and

persons at high altitudes are more affected by carbon monoxide than others.

Early signs of carbon monoxide poisoning resemble the ﬂu - headache, dizziness, and/or nausea. If you have these signs, the

heater may not be installed or working properly. GET FRESH AIR AT ONCE!

Have the heater serviced before using it again.

Vent-Free Gas Log Sets*

Models: UVLC18RN, UVLC24RN, UVLC30RN (Natural Gas)

UVLC18RP, UVLC24RP, UVLC30RP (Propane)

CE RTI FI E D

20000333 7/06 Rev. 12

*These logsets are not for exterior use.

This appliance may be installed in an aftermar-

ket, permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases.

INSTALLER PLEASE NOTE:

DO NOT begin installation of this gas logset

until all instructions have been read and under-

stood.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

2 UVLC Series

General Information

IN ORDER TO ASSURE A SAFE AND EFFECTIVE

INSTALLATION, ONLY A QUALIFIED SERVICE

PERSON WHO IS FAMILIAR WITH THE BUILDING

CODES AND INSTALLATION TECHNIQUES AP

PROPRIATE TO YOUR AREA MAY INSTALL AND

SERVICE THIS APPLIANCE.

• In order to avoid any possible gas leaks, apply pipe joint com-

pound to all non-ﬂared, threaded connections involved in this

installation. For propane, the joint compound must be resistant

to the corrosive action of propane.

• To check for leaks, always use a soapy water solution or a

sniffer. Never test by using an open ﬂame.

• The area around the gas logset must be free of all combus-

tible materials, especially gasoline or other highly ﬂammable,

vapor producing liquids.

• Due to high temperatures, locate this logset away from both

high trafﬁc areas and furniture and draperies.

• Children and adults alike should be aware of the high surface

temperatures; to avoid the risk of burns or ignition of clothing

they should stay away.

• Do not touch any part of the logset other than the controls

while it is operating or immediately after you turn it off.

• Supervise young children and pets carefully when they are in

the room where the logset is operating.

• Do not place clothing or other ﬂammable material on or near

the logset.

• Make sure that any safety screen or guard, removed during

servicing, has been replaced before you use the logset.

• Do not, under any circumstances, install the logset in any

bedroom, bathroom, other small, enclosed room, mobile home

or recreational vehicle.

• Do not install the logset in a drafty area or use it with any

after-market blower system that may cause drafting and conse-

quently alter the ﬂame pattern.

• It is imperative that you keep clear all burner areas, control

compartments and passageways for circulating air.

• Do not move the logset in any way that might dislodge the

logs from their ﬁxed positions. If you bump the logset check to

see if you have dislodged anything.

• Vent-free logsets require additional fresh air. You may supply

additional fresh air with any combination of: opening windows or

doors; or by operating a central furnace blower or exhaust fan.

• Provide adequate clearances around air openings into the

combustion chamber and adequate accessibility clearance for

servicing and proper operation. NEVER obstruct the front open-

ing of the ﬁreplace.

• Avoid propane tank dropping below 25% full. This will help

prevent soot from occurring.

The Logsets have been designed and tested to operate

safely when installed according to the installation instruc-

tions contained in this manual. Read all instructions

before starting the installation.

• The vent-free gas logset must be installed only in a ﬁreplace

constructed of noncombustible material.

• These logsets are not for exterior use.

• The logset should be inspected before use and at least an-

nually thereafter. More frequent cleaning may be necessary

because of excessive lint from carpeting or bedding material.

• In the United States, the installation and operation must

conform to local codes or, in the absence of local codes, with

the National Fuel Gas Code, ANSI Z223.1/NFPA 54, latest edi

tion and with the National Electrical Code, ANSI/NFPA70 (latest

edition). State or local codes may only allow operation of this

appliance in a vented conﬁguration. Check your state or local

codes. In Canada check local province for proper use or CSA-

B149. Refer to pages 7 and 8 for installation details.

• The gas logset and its individual shutoff valve must be dis-

connected from the gas supply piping system during any pres-

sure testing of that system at test pressures in excess of 1/2

p.s.i.g. (3.5 kPa.) The gas logset must be isolated from the gas

supply piping system by closing its individual manual shutoff

valve during any pressure testing of the gas supply piping sys-

tem at test pressures equal to or less than 1/2 p.s.i.g. (3.5 kPa.)

• Do not, under any circumstances, burn solid fuel (wood, pa-

per, coal) in the masonry or UL127 factory built ﬁreplace where

you have installed your logset. Do not use it for cooking. Put

nothing on top of the logs.

• The logset must be compatible with its fuel. Natural gas

requires different hardware than propane. Never attempt to use

natural gas with a propane logset or vice versa.

• For a propane burning logset, the supply tank must include a

high to low gas pressure regulator. The tank must be outdoors.

Do not, under any circumstances, locate supply tanks inside

any structure.

• The ﬁreplace must include a screen made of chain mesh or

a similar material. You must keep the screen closed at all times

during the operation of the logset; it will protect you in the event

of an explosion.

• WARNING: If the ﬁreplace contains glass doors, they must

remain fully open at all times during the operation of the logset,

allowing combustion air to circulate.

Proposition 65 Warning:

Fuels used in gas, wood-

burning or oil ﬁred appliances, and the products of

combustion of such fuels, contain chemicals known to

the State of California to cause cancer, birth defects

and other reproductive harm.

California Health & Safety Code Sec. 25249.6

UVLC Series

WARNING

This appliance is for installation in a solid-fuel

burning masonry, ﬁreplace with a working ﬂue,

a U.L.-127 listed manufactured solid-fuel burn-

ing ﬁreplace, in any Majestic ventless ﬁrebox,

or in any listed ventless ﬁrebox enclosure

certiﬁed to I.A.S. U.S. Requirement 2-97 or ANSI

Z21.91.

NOTICE

This is an unvented gas-ﬁred heater. It uses air

(oxygen) from the room in which it is installed. Pro-

visions for adequate combustion and ventilation air

must be provided. Refer to pages 5 and 6.

Installation Requirements

The ﬁreplace must meet the minimum dimensions listed below. (Fig. 1) Do not install the logset if the ﬁreplace does

not meet these minimums.

Pressure Test Points

The gas control is equipped with a captured screw-type

pressure test point, therefore it is not necessary to pro-

vide a 1/8” test point upstream of the control.

Odor During Operation

Neither natural gas nor propane gas give off an odor

when burned. The nature of a vent free combustion

system, however, is such that odors may occasionally be

produced during heater operation when impurities exist

in the immediate area. Cleaning solutions, paint, sol-

vents, cigarette smoke, candles, adhesives, new carpet

or textiles, etc., all can create fumes. These fumes may

mix with combustion air and can create odor. Such odors

will disappear over time, however, the condition can be

alleviated by opening a window or otherwise providing

additional ventilation to the area.

Min. Fireplace Dimensions

A B C D

Logset Gas Front Rear Overall Overall Pressure (w.c.) Manifold Min. Input Max. Input Setting

Width Width Depth Height Min. Max. Pressure BTU/hr BTU/hr Front Rear

18” UVLC18RN 30” 17” 15” 18” 5.5” 14.0” 3.5” 22,000 30,000 3/8” 3/8”

Open Open

24” UVLC24RN Natural 33” 20” 15” 18” 5.5” 14.0” 3.5” 29,000 39,000 Full 3/8”

Open Open

30” UVLC30RN 36” 25” 15” 18” 5.5” 14.0” 3.5” 29,000 39,000 Full 3/8”

Open Open

18” UVLC18RP 30” 17” 15” 18” 11.0” 14.0” 11.0” 22,000 30,000 Full Full

Open Open

24” UVLC24RP Propane 33” 20” 15” 18” 11.0” 14.0” 11.0” 29,500 39,000 3/8” Full

Open Open

30” UVLC30RP 36” 25” 15” 18” 11.0” 14.0” 11.0” 29,500 39,000 3/8” Full

Open Open

Inlet Supply Air Shutter

A. Front width B. Rear width

C. Depth D. Height

Fig. 1 Minimum ﬁreplace dimensions.

FD370-2

Fireplace

dimensions/vl18

3/25/99

FD370-2

High Elevations

Input ratings are shown in BTU per hour and are

certiﬁed without deration from elevations up to

4,500 feet (1,370m) above sea level.

Nuisance outages may occur at altitudes above

4,500 feet (1,370m) if dirt, dust, lint and/or cobwebs

are allowed to accumulate on burner and/or ODS

pilot. Monthly inspection and cleaning is recom-

mended for altitudes above 4,500 feet (1,370m)

For elevations above 4,500 feet (1,370m) in USA,

installations must be in accordance with the cur-

rent ANSI Z223.1/NFPA 54 and/or local codes hav-

ing jurisdiction.

In Canada, please consult provincial and/or local

authorities having jurisdiction for installations at

elevations above 4,500 feet (1,370m)

4 UVLC Series

Planning

Planning the installation is an important ﬁrst step. It will

save time and money later in the actual installation. In

planning the installation, consider:

• Where the heater will be located.

• All components needed to complete the installation.

• DO NOT use this heater in sleeping quarters, mobile

homes, or in recreational vehicles.

• Installation and repair should be done by a qualiﬁed

service person.

• DO NOT use this heater if any part has been under

water. Immediately call a qualiﬁed technician to inspect

the appliance and replace any part of the control sys-

tem and any gas control which has been under water.

• When used as an unvented heater, always ensure

that there is adequate ventilation from the room where

the appliance is operating. This appliance is equipped

with and ODS (oxygen depletion sensor) pilot light safe-

ty system designed to shut off the appliance if enough

fresh air is not available.

THIS APPLIANCE MUST NOT BE USED WITH GLASS

DOORS IN A CLOSED POSITION .

Keep the burner and control compartment clean. See

installation and operating instructions supplied with the

heater.

WARNING: During manufacturing, fabricating, and

shipping, various components of this appliance are

treated with certain oils, ﬁlms, or bonding agents.

These chemicals are not harmful, but may produce

annoying smoke and smells as they are burned off

during the initial operation of the appliance, pos-

sibly causing headaches or eye or lung irritation.

This is a normal and temporary occurrence. The

initial break-in operation should last 2-3 hours with

the burner at its highest setting. Provide maximum

ventilation by opening windows, doors, and the

chimney ﬂue to allow odors to dissipate. Any odors

remaining after this initial break-in will be slight and

will disappear with continued use.

This appliance operates as an unvented domestic room

heater when ﬁtted to a masonry or factory-built wood-

burning ﬁreplace with the ﬂue damper closed, or as

a decorative appliance when the ﬂue damper is fully

open. It must not be used for any other purpose and

must be ﬁtted in a masonry or factory-built ﬁreplace or

ventless ﬁrebox enclosure.

State, provincial or local codes may only allow opera-

tion of this appliance in a vented conﬁguration. Check

your state, provincial or local codes. If unvented room

heaters are not permitted, the ﬁreplace vent damper

must be locked open at the minimum vent area required

by local codes or by the National Fuel Gas Code (ANSI

Z223.1/NFPA 54, latest edition) and CSA B149 Installa-

tion Codes for Gas Burning Appliances.

When installed as a Decorative Gas Appliance for

installation in a solid-fuel burning ﬁreplace, a mini

mum permanent free opening of 29 square inches

must be maintained with a ﬁxed damper stop pro-

vided with the appliance. Minimum ﬂue size for this

appliance is 29 square inches.

Installation Precautions

1. This vent-free gas appliance and its components

have been tested and will operate safely when installed

in accordance with this Installation Manual. Read all

instructions before starting the installation, and follow

these instructions carefully \ installation to maximize the

appliance’s beneﬁt and safety. Failure to follow them

will void your warranty and may present a ﬁre hazard.

2. After opening the carton, refer to Parts Identiﬁcation

on Page 15 and 16, and remove the various parts.

Report to your dealer if any parts were damaged in

shipment.

The CFM Corporation warranty will be voided by,

and CFM Corporation disclaims any responsibility

for, the following actions:

• Installation of any damaged appliance.

• Modiﬁcation of the appliance.

• Installation other than as instructed by

CFM Corporation.

• Improper positioning of the gas logs.

• Installation and/or use of any component

part or accessory not manufactured or approved

by CFM Corporation, not withstanding any inde-

pendent testing laboratory or other third-party

approval of such component part or accessory.

Any such action may create a possible ﬁre hazard.

Consult your local building codes.

This heater shall not be installed in a conﬁned

space unless provisions are provided for adequate

combustion and ventilation air.

WARNING

Improper installation, adjustment, alteration, ser-

vice, or maintenance can cause injury of proper-

ty damage. Refer to this manual. For assistance

or additional information, consult a qualiﬁed

installer, service agency, or the gas supplier.

UVLC Series

Fresh Air Requirements

for Combustion and Ventilation

If your home meets all of the above criteria, you must

provide additional fresh air for the appliance as detailed

on Page 6.

If your home does not meet the above criteria, follow

the procedure below.

Determine If You Have a Conﬁned

or Unconﬁned Space

Use the following formula to determine if you have a

conﬁned or unconﬁned space.

Space is deﬁned as the room in which you will install

the heater, plus any adjoining rooms with doorless pas-

sageways or ventilation grilles between the rooms.

The National Fuel Gas Code deﬁnes a conﬁned space

as a space whose volume is less than 50 cubic feet per

1,000 BTU per hour input rating (4.8m

per Kw) of the

aggregate (total) input rating of all appliances installed

in that space and an unconﬁned space as a space

whose volume is not less than 50 cubic feet per 1,000

BTU per hour (4.8m

per Kw) of the aggregate input

rating of all appliances installed in that space. Rooms

communicating directly with the space in which the ap-

pliances are installed, through openings not furnished

with doors, are considered a part of the unconﬁned

space.

1. Determine the volume of space (length x width x

height). Include adjoining rooms connected by doorless

passageways or ventilating grilles.

Example: A room that is 18’ x 12’ x 8’ has a volume of

1728 cubic feet. An adjoining open kitchen that is 10’

x 12’ x 8’ has a volume of 960 cubic feet. An adjoining

open dining room is 12’ x 12’ x 8’ with a volume of 1152

cubic feet. The total volume is 3840 cubic feet.

2. Divide the volume of space by 50 cubic feet. The

result is the maximum BTU/hour the space can support.

Example: 3840 cubic feet divided by 50 = 76.8 or

76,800 BTU/hour.

3. Add the BTU/hour ratings of all fuel-burning applianc-

es installed in the same space, including the following:

Gas Water Heater Gas Furnace

Gas Fireplace Logs Vent-free Gas Heater

Vented Gas Heater* Other Gas Appliances*

* Do not include Direct-vent appliances as these

use outdoor air for combustion and vent to the

outdoors.

Modern construction standards have resulted in homes

that are highly energy-efﬁcient and that allow little heat

loss. Your home needs to breathe, however, and all

fuel-burning appliances need fresh air to function prop-

erly and safely. Exhaust fans, clothes dryers, ﬁreplaces,

and other fuel burning appliances all use the air inside

the building. If the available fresh air supply is insufﬁ-

cient to meet the demands of these appliances, prob-

lems can result.

The vent-free logs sets have speciﬁc fresh air require-

ments. You must determine that these requirements

will be met within the space where the appliance will be

installed. The following information will help you ensure

that adequate fresh air is available for the heater to

function properly.

Provide for Adequate Ventilation

Any space within a home can be classiﬁed in these

categories:

1) Unusually tight construction

2) Conﬁned space

3) Unconﬁned space.

First, determine which classiﬁcation deﬁnes the intend-

ed installation space.

Unusually Tight Construction

You must provide additional fresh air if the space falls

into this classiﬁcation. Unusually Tight Construction is

deﬁned as construction wherein:

a. Walls and ceilings exposed to the outside atmo-

sphere have a continuous water vapor barrier with a

rating of one perm or less, with openings gasketed or

sealed, and

b. weather stripping has been added on openable win-

dows and doors and

c. caulking or sealants are applied to areas such as

joints around windows and door frames, between sole

plates and ﬂoors, between wall and ceiling joints, be-

tween wall panels, at penetrations for plumbing, electri-

cal, and gas lines, and at all other openings.

This heater must have fresh air for proper opera-

tion. If it does not, poor fuel combustion could

result. Read the following instructions to ensure

proper fresh air supply for this and other fuel-

burning appliances in your home.

WARNING

Installation Requirements

6 UVLC Series

4. Compare the maximum BTU/hour rating the space

can support with the total BTU/hour used by the appli-

ances.

Example: 76,800 BTU/hour the space can support

80,000 BTU/hour used by appliances

In this example, the maximum BTU/hour that the space

can support is less than the total used by the appli-

ances. The space is considered to be Conﬁned Space.

Additional air must be provided to meet the require-

ments on the vent-free gas log set.

The installation and the provisions for combustion and

ventilation air must conform with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or the CSA-B149.1 Instal-

lation Code (Series).

A conﬁned space may be ventilated in two ways:

A. Open up or provide at least two ventilating grilles to

an adjoining unconﬁned space. (Fig. 2)

Each of the two grilles must provide an opening of at

least 50 square inches, with all opening dimensions be-

ing at least 3”. One grille must be within 12” of the ceil-

ing; the other within 12” of the ﬂoor. (If the total exceeds

100,000 BTU/hour, additional grilles will be needed.)

B. Vent the room directly to the outdoors. (Provide one

square inch of opening for each 4,000 BTU/hr.)

For further information on ventilation guidelines and siz-

ing speciﬁcations, follow the National Fuel Gas Code/

NFPA 54/ANSI Z223.1/NFPA 54, Section 5.3.

If the total BTU/hour used by the appliances is less than

the maximum BTU/hr the space can support, the room

meets the Unconﬁned Space criteria and no further

ventilation is needed.

WARNING: Before installing the gas log set in a solid-

fuel burning ﬁreplace, the chimney ﬂue and ﬁrebox must

be cleaned of soot, creosote, and loose paint by a quali-

ﬁed chimney cleaner.

WARNING

This heater shall not be installed in a conﬁned

space or unusually tight construction unless

provisions are made for adequate combustion

and ventilation air.

WARNING

If the area in which the heater may be operated

is smaller than that deﬁned as an unconﬁned

space, or if the building is of unusually tight

construction, provide adequate combustion and

ventilation air by one of the methods described

in the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, 1992, Section 5.3, or applicable codes.

VO370-2

Ventilation

options

3/26/99 djt

Fig. 2 Ventilation options for conﬁned spaces.

OPTION 1 -

Vents to Ad-

joining Rooms

OPTION 2 -

Remove Door

to Adjoining

Room

OPTION 3 -

Vents to Ad-

joining Rooms

12”

VO370-2

Example:

Gas Range 55,000 BTU/hour

Vent-Free LogSet +25,000 BTU/hour

Total 80,000 BTU/hour

UVLC Series

Preparing the Fireplace

Gas Line Preparation

Before connecting the appliance, turn off all gas appli-

ances. Close the main gas valve at the gas meter or

appliances. Close the main gas valve at the gas meter

or LP tank. Make certain there is good ventilation where

the installation will be made. Installation should comply

with all applicable building codes and ANSI Z223.1/

NFPA 54, latest edition or CSA B-149.1. Use LP gas-re-

sistant pipe compound to seal threaded joints.

Installation to Existing Gas Line

There should be a manual ON/OFF valve within easy

reach of the appliance. If not, before installation of the

appliance, make certain a valve is installed. There may

be a second valve on the line close to the point where

the ﬁreplace line branches off the main gas supply line.

During installation, make certain this valve is OFF.

Manufactured Fireplace Preparation

Refer to the manufacturer’s ﬁreplace installation manual

for the speciﬁc method of running the gas line into the

ﬁreplace. The following method is typical of most manu-

factured ﬁreplaces.

Insert a 1/2” gas pipe through the gas line tube provided

by the manufacturer, from outside the ﬁreplace, as

marked by the manufacturer. An ON/OFF valve should

be placed within easy reach of the appliance. After the

gas supply is installed, reinstall the insulation removed

from the gas line tube, and pack it around the pipe, to

prevent cold air entry and to protect the gas line. (Fig. 3)

NOTE: The gas pipe should not come into contact with

any wood structure until it has reached a point at least

one (1) inch away from the ﬁreplace side. (Fig. 3)

Masonry Fireplace Installation Preparation

A 1/2 inch gas supply line must be supplied to the

ﬁrebox. In most cases, this will require drilling a gas line

access hole through the masonry wall. The gas supply

line should then be sealed in the access hole with mor-

tar. The gas supply line should also have a valve within

easy reach of the appliance. Use only N.P.T. black iron

gas line. (Do not use cast-iron pipe).

Clean the ﬁreplace and chimney (if used) of any ashes,

soot, creosote, or obstruction. This will minimize any

smell from the ﬁreplace. We recommend cleaning by a

chimney sweep.

Flue Damper Preparation

The vented ﬁreplace damper should be fully opened

when operating the appliance as a vented log set. A

damper stop clamp with set screw is provided as a

means to prevent full closure of the ﬁreplace damper

blade. The clamp is designed to prevent accidental clo-

sure of the damper when in use. (Fig. 4) (If the damper

stop cannot be installed, the installer should install a

permanent damper stop that will keep the damper open

minimum of 1¹⁄₂”).

Do not allow fans to blow directly into the ﬁre-

place. Avoid any drafts that alter burner ﬂame

patterns.

WARNING: Do not use a blower insert, heat ex-

changer insert, or other accessory not approved

for use with this gas log set.

DO NOT burn solid fuels in a ﬁreplace where an

unvented gas room heater or log set is installed.

Any outside air ducts and/or ashdumps in the

ﬁreplace must be permanently closed at time of

appliance installation.

Do not install this appliance in bedrooms or

bathrooms.

WARNING: Any change to this heater or its con

trols can be dangerous.

WARNING:

Installation Instructions

760/Fplc Access. Ports

968/598UVL/UVHL

7/25/98

Fig. 3 Gas line installation - factory-built ﬁreplaces.

Gas Access

Holes

Outside Air Access

Electrical

Access

Gas Supply

Line

Repack

Insulation

Ceramic

Knockout

Hole in

Outer

Casing

760

1”

8 UVLC Series

Manufactured Fireplace

Damper Stop Installation

Damper Stop #3030176 is designed for use with CFM

Corporation BR, BC, SR, SC,TF and TL Series ﬁre-

places.

1. Open the ﬁreplace damper. The damper must be in

the open position in order to attach the damper stop.

2. From inside the ﬁreplace, locate the damper locking

bracket on the left side of the combustion dome. (Fig.

3. Align the two slots on either side of the cutout on the

damper stop with the two small holes on the angled

portion of the damper locking bracket. Attach the

damper stop with the screws provided. (Fig. 6)

NOTE: Some of the early units may not have the holes

in the end of the damper locking bracket. If this is the

case, use the damper stop as a template to drill two

1/8” holes in the damper locking bracket to mount the

damper stop.

LS761/Damper Clamp Location

968/598 UVL/UVHL

7/27/98

Damper

Stop

Damper

Stop

761

Fig. 4 Damper stop placement.

LS855

Attach damper stop

11/99

Damper Locking

Bracket

Damper

Stop

#3030176

Attachment Screws

- Two Provided

LS855

Fig. 6 Attach the damper stop.

LS854

Locate damper

lock bracket

11/99

Damper Locking Bracket

LS854

Fig. 5 Locate the damper locking bracket inside the ﬁreplace

dome.

UVLC Series

Burner Assembly Location

Centrally locate the unit in the ﬁreplace, far enough

back into the ﬁrebox to accomplish adequate draft (if

use as a vented appliance is planned). Ensure the front

grate feet sit inside the front edge of the ﬁreplace a

minimum of 3”. (Fig. 7b)

Clearances

To ensure the safe installation into a masonry or fac-

tory-built ﬁreplace, carefully observe the following

instructions:

1. Sidewall Clearances: The clearance from the inside

of the front opening of the ﬁreplace to any combustible

wall should not be less than 3¹⁄₂”. (Fig. 7a)

2. Ceiling Clearances: The ceiling height should not be

less than 42” from the top of the ﬁreplace opening. (Fig.

7A)

3. Mantel Clearances:

When installing an ANSI Z21.11.2 ventless appliance,

the ﬁnishing material used for the mantel must be rated

at 250°F or greater. Refer to the ﬁrebox instructions for

any further information.

Without Hood: If no hood is installed, then there must

be noncombustible material from the top front opening

of the ﬁreplace to a height of at least 20” and the full

width of the ﬁreplace. A combustible ﬂat mantel shelf

can be no closer than 38¹⁄₂” from the top of the ﬁreplace

opening. (Fig. 7b)

With Hood: If a hood is installed there must be non-

combustible material from the top front opening of the

ﬁreplace to a height of 7¹⁄₂” and the full width of the ﬁre-

place. A combustible ﬂat mantel shelf may be installed

according to the detail in Fig. 7c.

3A. Mantel Depth: A combustible mantel can be no

deeper than 8”, at 12” above the hood. (Figs. 7b, 7c)

4. Grate Clearance: The minimum clearance between

the front legs of the grate and the front edge of the ﬁre-

place is 3”. (Fig. 7b)

MC656-2

clearances

3/26/99 djt

42”

3¹⁄₂”

Min.

Noncombustible

Facing Material

Ceiling

3¹⁄₂”

Min.

MC656-2

763 Fplc Clrnc Top View

UVL/UVHL

7/28/98

Top View

Mantel Trim

Finished Wall Mate

rial

Firebox

3¹⁄₂”

Noncombustible Facing

Material

3¹⁄₂”

763

Front View

764 Fplc Clearance, Side View

UVL/UVHL

7/28/98

8”

38¹⁄₂”

20”

Standoff

Noncombustible

Material

Front Edge of

Grate

3”

4”

Without Hood

765 Fplc w/ Hood, detail

UVL/UVHL

7/27/98

With Hood

Flat Mantel

Shelf

8”

7¹⁄₂”

12’

4”

Standoff

Seal with

Noncombus-

tible Material

4”

Hood

764

765

Fig. 7 Mantel Clearances.

10 UVLC Series

Positioning the Logs

The logs must be positioned on the grate and locating

pins as shown in Figure 8.

Gas logs must be properly positioned or the appliance

will not function properly, and may result in soot accu-

mulation on the inside of the ﬁrebox and/or on the gas

logs. Make sure there is no ﬂame impingement on the

logs which could result in excessive carbon monoxide

emissions.

Make sure each bottom log engages the locator pins

on the grate, and top logs are properly positioned in

notches on the tops of the lower logs.

The contents of the small bags of volcanic rock may

only be placed as shown in Figure 8. Apply loose mate-

rial per instructions manual. Do not apply extra material

or material not supplied with the heater. Replace only

with Part No. 57897.

Gas Line Connection

Check the gas type. Use only the gas type indicated on

the appliance rating plate. If the gas listed on the plate

is not the type of gas supplied, DO NOT INSTALL the

log set. Contact your dealer for the proper model.

Always use an external regulator for all LP applances,

to reduce the supply tank pressure to a maximum of

14” w.c. This is in addition to the regulator ﬁtted to the

heater.

The normal gas connection is made at the left side (fac-

ing the unit). If a right-side connection is desired, the

connecting pipe may be directed under or behind the

rear of the appliance, to terminate at the left-hand side

for connection to the inlet of the appliance.

Connect the appliance to the gas line using ﬁttings and

aluminum tubing provided.

Close the valve knob on the appliance, turn the main

gas supply valve ‘ON’ and carefully check all gas con-

nections for leaks, with a soapy water solution or a

sniffer. DO NOT TEST FOR LEAKS WITH AN OPEN

FLAME.

Upon completing your gas line connection, a small

amount of air will be in the gas lines. When ﬁrst lighting

the pilot, it will take a few minutes for the lines to purge

themselves of air. Once the purging is complete, the

pilot and burner will light and operate as indicated in

this manual. Subsequent lightings of the appliance will

not require purging.

Check the inlet pressure to the appliance, to ensure that

it is as shown in the table on page 2. The minimum is

for the purpose of input adjustment.

The pressure is controlled by the regulator and should

be checked at the pressure test point located in the

control valve body.

The pressure should be checked with the appliance

burning and the control set on ‘HIGH’.

The pressure regulator is preset and locked to avoid

tampering. If the pressure is not as speciﬁed, replace

the regulator.

After measuring the pressure, replace the test point

plug. Ensure there are no leaks, then place the logs in

their speciﬁed positions.

WARNING

Connection directly to an unregulated LP tank can

cause an explosion.

During the initial purging and subsequent light-

ings, never allow the gas valve control knob to

remain depressed in the ‘Pilot’ position without

lighting the pilot with a match or piezo ignitor.

There is a possibility of odor fade in LP. Never

install an LP appliance or service line below grade

without a gas detector.

WARNING

Failure to position the parts in accordance with

these diagrams or failure to use only parts spe-

ciﬁcally approved for use with this appliance may

result in property damage or personal injury.

This appliance is equipped for (natural or pro-

pane) gas. Field conversion is not permitted.

UVLC Series

Fireplace Screen

The ﬁreplace screen must be in place when the appli-

ance is operating, and unless other provisions for com-

bustion air are made, the screen must have openings

for the introduction of combustion air.

LG116

UVLC24 log placement

11/99

Fig. 8 Placing the logs on the grate assembly.

LG116

PILOT

OFF

PILOT

ADJ

T PT H

HV110

Honeywell valve

w/GWSK wall switch

11/99

TP/TH Terminal

TH Terminal

To Optional

GWSK Wall

Switch

HV110

Fig. 9 Connecting a wall switch to the valve termnals.

Remote Wall Switch

(Optional Model GWSK)

1. Thread wire through the electrical knockout located

on either side of the ﬁreplace. Do not cut the wire

or insulation on metal edges. Ensure that the wire

is protected. Run the other end to a conveniently

located wall receptacle box.

2. Attach the wire to the switch and install the switch

into the receptacle box. Attach the cover plate to the

switch.

3. Connect the remaining ends of the optional switch

to the valve at Terminal 3 and the tab connector on

Terminal 1. (Fig. 9)

NOTE: If any of the original wire as supplied with the

appliance must be replaced, it must be replaced with a

wire of at least a 60°C temperature rating.

12 UVLC Series

The First Firing

On completing the gas line connection, a small amount

of air will be trapped in the gas line. When you ﬁrst light

the unit with the pilot light, it will take a few minutes to

purge the trapped air. Once you have purged the gas

line, the pilot and burner will light and operate normally.

Subsequent lightings of the appliance will not require

purging the gas line.

When lit for the ﬁrst time, the appliance will emit a slight

odor for an hour or two. This is due to paint and lubri-

cants used in the manufacturing process curing under

heat. This is normal. You may wish to have the windows

open to dissipate any odors during the curing process.

Flame Appearance

To obtain proper operation, it is imperative that the pilot

and main burner ﬂame characteristics are steady, not

lifting or ﬂoating. Refer to Figure 11 for proper burner

ﬂame appearance and Figure 12 for proper pilot ﬂame

appearance.

Typically, the top 1/8” of the thermopile should be en-

gulfed in the pilot ﬂame. (Fig. 12)

P102

Honeywell pilot

flame

6/16/99 djt

Thermopile

P102

Fig. 12 Proper pilot ﬂame appearance.

Operating Instructions

HV101a

Honeywell valve

UVL

3/18/99 djt

PILOT

OFF

PILOT

ADJ

Fig. 10 Honeywell Valve.

Piezo Igniter

Regulator Knob

Control Knob

HV101a

LG116

log flames

11/99

Yellow

Flames

Fig. 12 Proper burner ﬂame appearance.

Red glow

LG116

UVLC Series

3. Open control access panel.

4. Push in gas control knob slightly and turn clock-

wise to “OFF”. Do not force.

5. Close control access panel.

1. STOP! Read the safety information above.

2. Turn off all electrical power to the ﬁreplace.

3. For MN/MP/TN/TP appliances ONLY, go on to

Step 4. For RN/RP appliances turn the On/Off

switch to “OFF” position or set thermostat to

lowest level.

4. Open control access panel.

5. Push in gas control knob slightly and turn

clockwise to “OFF”.

10. Push the control knob all the way in and hold.

Immediately light the pilot by repeatedly depress-

ing the piezo spark ignitor until a ﬂame appears.

Continue to hold the control knob in for about one

(1) minute after the pilot is lit. Release knob and it

will pop back up. Pilot should remain lit. If it goes

out, repeat steps 5 through 8.

FOR YOUR SAFETY READ BEFORE LIGHTING

instructions.

• If you cannot reach your gas supplier, call

the Fire Department

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will not

push in or turn by hand, do not try to repair it, call a

qualiﬁed service technician. Applying force or any

attempted repair may result in a ﬁre or explosion.

D. Do not use this ﬁreplace if any part has been under

water. Immediately call a qualiﬁed service techni-

cian to inspect the heater and to replace any part of

the control system and any gas control which has

been under water.

A. This heater has a pilot which must be lit manu

ally. When lighting the pilot follow these instruc-

tions exactly.

B. BEFORE LIGHTING smell all around the heater

area for gas. Be sure to smell next to the ﬂoor

because some gas is heavier than air and will

settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any ﬁreplace

• Do not touch any electric switch

• Do not use any phone in your building

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

To Turn Off Gas To Heater

Lighting And Operating Instructions

1. Turn the On/Off switch to Off position or set the

thermostat to lowest setting.

2. Turn off all electric power to the ﬁreplace if

service is to be performed.

Lighting Instructions

6. Wait ﬁve (5) minutes to clear out any gas. Then

smell for gas, including near the ﬂoor. If you

smell gas, STOP! Follow “B” in the safety infor-

mation above. If you do not smell gas, go to the

next step.

7. Remove glass door before lighting pilot. (See

Glass Frame Removal section).

8. Visibly locate pilot by the main burner.

9. Turn knob on gas control counterclockwise

to “PILOT”.

• If knob does not pop up when released, stop

and immediately call your service technician or

gas supplier.

• If after several tries, the pilot will not stay lit,

turn the gas control knob to “OFF” and call your

service technician or gas supplier.

11. Replace glass door.

12. Turn gas control knob to “ON” position.

13. For RN/RP appliances turn the On/Off switch to

“ON” position or set thermostat to desired setting.

14. Turn on all electrical power to the ﬁreplace.

WARNING:If you do not follow these instructions exactly, a ﬁre or explosion

may result causing property damage, personal injury or loss of life.

Euro SIT SIT NOVA

Honeywell

PILOT

OFF

PILOT

FP1067

lighting instruction

knobs

3/9/01 djt

3/8" - 1/2"

FP1068

Lighting instructions

Pilots

14 UVLC Series

Troubleshooting

Honeywell Valve

• Supply line hooked up

• Shutoff valve open

• Lockout has engaged. Wait 60 seconds

and try again

• Piezo screws are tight for good ground

• For spark at electrode while depressing

piezo - 1/8” gap to pilot hood needed

• All wiring connections

• Replace piezo ignitor

• For air in the lines

• Thermopile needs a minimum of 325mV

• All wiring connections

• Replace thermopile

• Thermocouple needs a minimum of 14mV

• Defective valve. turn to pilot, meter should

read greater than 100mV. If not, replace the

valve.

• Valve turned on

• Wall switch is not turned on

• Thermopile needs a minimum of 325mV

• Plugged burner

Gas supply on

Pilot lights with Piezo

Pilot stays lit

Pilot lights main

burner

System OK

YES

START

CHECK

UVLC Series

UVLC System Maintenance

The UVLC burner and control system consists of:

• Chassis

• Gas Oriﬁce

• Grate assembly

• Six (6) decorative logs (UVLC18, UVLC24)

Seven (7) decorative logs (UVLC30)

• Gas valve assembly

The logs can get very hot. Handle them only when

they are cool.

Most of these components require only occasional

check-up and cleaning. Some may require adjustment.

If repair is needed, it should be performed by a qualiﬁed

technician.

In order to properly clean the burner and pilot assembly,

turn off the gas to the unit and remove the logs, expos

ing the burner and pilot assembly. Clean all foreign ma-

terials from the top of the burner. Check to make sure

that all burner parts are clean. Visually inspect the pilot.

Brush or blow away any dust or lint accumulations.

WARNING:

Failure to keep the primary air openings

of the burner clean may result in sooting and property

damage.

NOTE: The burner and pilot assembly should be

checked for any dust or lint at least every six months.

Replacement Parts

Contact the factory for questions about prices and poli-

cies covering replacement parts. Parts will be shipped

at prevailing prices. Normally, all parts can be ordered

through your Majestic distributor or dealer.

Refer to the parts illustration and listing on pages 16

and 17.

Maintenance and Safeguards

Keep the control compartment, logs and burner area

around the logs clean by vacuuming or brushing at least

twice a year.

THE LOGS CAN GET VERY HOT. HANDLE THEM

ONLY WHEN THEY ARE COOL.

Always turn off gas to the pilot before cleaning. For

relighting, refer to the lighting instructions.

The appliance and venting system (if used) should be

inspected before initial use, and at least annually by a

qualiﬁed ﬁeld service person.

Always keep the appliance area clear and free from

combustible materials, gasoline, and other ﬂammable

vapors and liquids.

Never obstruct the ﬂow of combustion and ventilation

air. Keep the front of the appliance clear of all obstacles

and materials.

Leave clearance of at least 36” from the front of the

ﬁreplace.

Although your gas logs are very realistic in appearance,

the ﬁreplace must not be used for burning any solid

fuels.

To avoid irreparable damage to the appliance or per-

sonal injury, matches, paper, garbage, or any other

material must not be placed or thrown on top of the logs

or into the ﬂames.

To avoid personal injury, do not touch hot surfaces

when the appliance is operating. Touch only the valve

control knob. Avoid contact with the grate feet or

prongs, or any other part which may be very hot.

Always ensure that the ﬁreplace screen is closed when

the appliance is operating.

Any safety screen or guard removed for servicing the

appliances must be replaced before operating the appli-

ance.

Close supervision is necessary when the appliances is

being operated near children.

The appliance is intended for use as a gas heater

mounted in a vented or unvented ﬁreplace as described

in the installation section of these instructions. It should

not be used for any other purpose.

Inspecting the Venting System

A vented ﬁreplace venting system is designed and con-

structed to develop a positive ﬂow adequate to remove

ﬂue gasses to the outside atmosphere. See vented

ﬁreplace installation instructions.

Any foreign objects in the venting system, except those

designed speciﬁcally for the venting system, may cause

spillage of the ﬂue gases into the room. In extreme situ-

ations, carbon monoxide poisoning or suffocation may

occur.

Periodic examination and cleaning of the venting

system of the solid-fuel burning ﬁreplace must be done

frequently by the home owner or a qualiﬁed agency.

16 UVLC Series

PILOT

ADJ

TPTH

Switch

(behind door)

15a/b

23a

23b

0333

UVLC parts

19a,b

2a,b

CFM Corporation reserves the right to make changes in design, materials, speciﬁcations, prices and discontinue colors and products at any time,

without notice.

UVLC Supreme Vent Free Gas Logs

1. Complete Log Set 20003423 20000327 20003428

1a. Back Log 20003425 7583198 20003430

1b. Log #V20 Cross Right 7583202 7583202 7583202

1c. Log #V19 Cross Left 7583199 7583199 7583199

1d. Front Log 20003424 7583197 n/a

1e. Left Middle Log 20003426 7583200 20003431

1f. Right Middle Log 20003427 7583201 20003432

Ref. Description UVLC18 UVLC24 UVLC30

UVLC Series

UVLC Supreme Vent Free Gas Logs (continued)

Ref. Description UVLC18 UVLC24 UVLC30

1g. Log #V43 Front Left n/a n/a 20004893

1h. Log #V44 Front Right n/a n/a 20004894

2a. Burner Supply w/Oriﬁces - Natural 20003050 20000329 20000329

2b. Burner Supply w/Oriﬁces - LP 20003687 20000318 20000318

3. 3/8” Flex Tubing 3304176 3304176 3304176

4. Volcanic Rock 20000198 20000198 20000198

5a. Damper Stop 3030176 3030176 3030176

5b. Damper Stop 4304045 4304045 4304045

6. Elbow Fitting 1/2” NPT (F) x 3/8” Flare 7523184 7523184 7523184

7. Lava Rock (Burner) 57897 57897 57897

8. Switch 1601597 1601597 1601597

9. Andiron Assembly 20005295 20005295 20005295

10. Swivel Door - Painted 20005340 20005345 20005345

11. Back Plate 20003023 20000321 20000321

12. Right Side Grate - Painted 20005338 20005338 20005338

13. Left Side Grate - Painted 20005339 20005339 20005339

14. Fettle - Painted 20005344 20005343 20005343

15a. Pilot Assembly - LP 55465 55465 55465

15b. Pilot Assembly - Natural 55464 55464 55464

16. Piezo Ignitor 20000062 20000062 20000062

17. Piezo Ignitor Cable 20000101 20000101 20000101

18. Ignitor Electrode Order Pilot Order Pilot Order Pilot

19a. Valve - LP 10000242 10000242 10000242

19b. Valve - Natural 10000235 10000235 10000235

20. ON/OFF Extension (Not shown) 20000007 20000007 20000007

21. HI/LO Extension (Not shown) 20000006 20000006 20000006

22. Pilot Bracket Assembly 20003530 20003530 20003530

23a. Pilot Shield 20003499 -- --

23b. Pilot Shield -- 20003500 20003500

24. Burner Housing Assembly 20003028 20000277 20000277

18 UVLC Series

Accessories

The following accessories are available from your Majestic Fireplaces Dealer. If you need additional information beyond what your

dealer can supply, contact CFM Corporation, 2695 Meadowvale Blvd., Mississauga, Ontario, Canada L5N 8A3 Attention: Director of

Technical Service.

Accessory Description Model Number

Hood

Required to protect wall above

ﬁreplace and/or mantel in certain

applications.

AH3244BK (BLACK)

AH3244PB (POLISHED BRASS)

Remote Control ON/OFF w/Batteries MRC1

ON/OFF Thermostat w/ Batteries MRC2

LCD ON/OFF Thermostat, Timer w/ Batteries MRC3

Remote Wall Switch Designed to provide remote on and off GWSK

control of burner ﬂame

Fireback Cast Iron Construction. Designed to enhance CFB24M

ﬂame effect with porcelain enamel

in ‘Midnight Black’.

AC110

Remote WAll Switch

5/7/99 djt

AC100

FIREPLA

CE HOOD

3/29/99 DJT

AC111

Fireback

from VErmont

5/7/99 djt

NOTE: If any of the original wire as supplied with

the appliance must be replaced, it must be re-

placed with a wire of at least a 105˚(C) temperature

rating.

Contact CFM Corporation with questions concerning

prices and policies covering replacement parts. Parts

may be ordered through your Majestic Fireplaces dis-

tributor or dealer.

You will need the following information when ordering

replacement parts:

• The appliance model number.

• The serial number.

• A description of the part.

Should you need additional information beyond what your

dealer can furnish, contact:

CFM Corporation

2695 Meadowvale Boulevard

Mississauga, Ontario

Canada L5N 8A3

Model and serial numbers are listed on the metal

rating plate attached to the burner assembly.

Record your model and serial numbers here to

ease future reference:

Model #

Serial #

UVLC Series

LIMITED WARRANTY & EXTENDED LIFETIME PROTECTION

For Majestic Fireplaces Gas Fireplace Products

BASIC WARRANTY:

CFM Corporation (hereinafter referred to collectively as the “Company”)

warrants that your new Majestic Fireplaces Gas Appliance is free from

manufacturing and material defects for a period of one year from date of

installation, subject to the following conditions and limitations.

EXTENDED LIFE TIME WARRANTY:

The heat exchanger, combustion chamber and ceramic burner parts of every

*CFM Corporation products are warranted for life to the original owner, subject

to proof of purchase and the following conditions and limitations:

1. This new Majestic Fireplaces product must be installed by a competent,

authorized service contractor. It must be installed and operated at all times in

accordance with the Installation and Operating instructions furnished with the

product. Any alteration, willful abuse, accident, or misuse of the product shall

nullify this warranty.

2. This warranty is non-transferrable, and is made to the original owner, provided

that the purchase was made through an authorized supplier of the Company.

3. This warranty is limited to the repair or replacement of part(s) found to be defective

in material or workmanship, provided that such part(s) have been subjected

to normal conditions of use and service, after said defect is conﬁrmed by the

Company’s inspection.

4. The Company may, at its discretion, fully discharge all obligations with respect

to this warranty by refunding the wholesale price of the defective part(s).

5. Any installation, labour, construction, transportation, or other related costs/

expenses arising from defective part(s), repair, replacement, or otherwise of

same, will not be covered by this warranty, nor shall the Company assume

responsibility for same. Further, the Company will not be responsible for any

incidental, indirect, or consequential damages, except as provided by law.

6. All other warranties - expressed or implied - with respect to the product, its

components and accessories, or any obligations/liabilities on the part of the

Company are hereby expressly excluded.

7. The Company neither assumes, nor authorizes any third party to assume, on its

behalf, any other liabilities with respect to the sale of this Majestic Fireplaces

product.

8. The warranties as outlined within this document do not apply to chimney

components or other non Majestic Fireplaces accessories used in conjunction

with the installation of this product.

9. The Company will not be responsible for . . .

a) Down drafts or spillage caused by environmental conditions such as near-

by trees, buildings, roof tops, hills, or mountains.

b) Inadequate ventilation or negative air pressure caused by mechanical

systems such as furnaces, fans, clothes dryers, etc.

10. This warranty is void if:

a) The ﬁreplace has been operated in atmospheres contaminated by chlorine,

ﬂuorine or other damaging chemicals.

b) The fireplace is subjected to prolonged periods of dampness or

condensation.

c) Any damage to the ﬁreplace, combustion chamber, heat exchanger or other

components due to water, or weather damage which is the result of, but

not limited to, improper chimney/venting installation.

d) Any alteration, willful abuse, accident, or misuse of the product.

GLASS DOORS & BRASS PLATED PARTS

Glass doors are not warranted for breakage due to misuse or accident.

Brass parts should be cleaned with lemon oil

only. Brass cleaners cannot be used.

Mortar mix and masonry cleaners may corrode the brass ﬁnish. The Company will

not be responsible for, nor will it warrant any brass parts which are damaged by

external chemicals or down draft conditions.

IF WARRANTY SERVICE IS NEEDED .

. .

1) Contact your supplier. Make sure you have your warranty, your sales receipt,

and the model/serial number of your Majestic Fireplaces product.

2) DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.

GARANTIE DE BASE:

CFM Corporation (aux présentes nommée la “Société”) garantit votre nouveau

foyer au gaz Majestic Fireplaces contre tous défauts de fabrication et de

matières premières pour une période d’un an à compter de la date d’installation,

sujet aux conditions et limitations suivantes.

GARANTIE A VIE PROLONGEE:

Les pièces de l’échangeur de chaleur, de la chambre à combustion et du brûleur

en céramique de tout produit *CFM Corporation sont garanties pour la vie de

l’acheteur d’origine, le tout sujet à une preuve d’achat et aux conditions et

limitations suivantes:

1. Ce nouveau produit Majestic Fireplaces doit être installé par un entrepreneur

de service autorisé et compétent. Il doit être installé et utilisé en tout temps

selon les instructions d’installation et de fonctionnement fournies avec le produit.

Toute altération, abus volontaire, accident ou mauvais usage du produit annulera

cette garantie.

2. Cette garantie n’est pas transférable et est offerte à l’acheteur au détail d’origine,

à condition que l’achat soit effectué par l’entremise d’un détaillant autorisé de

la Société.

3. Cette garantie est limitée à la réparation ou au remplacement de(des) pièce(s)

trouvée(s) défectueuse(s) en matières premières ou main-d’oeuvre, à condition

que lesdites pièces aient été sujettes aux conditions normales d’usage et

de service, après que ledit défaut a été conﬁrmé par une inspection par la

Société.

4. La Société peut, à sa discrétion, se décharger entièrement de toutes obligations

se rapportant à cette garantie en remboursant le prix de gros de la(des) pièce(s)

défectueuse(s).

5. Tous les frais/dépenses d’installation, de main-d’oeuvre, de construction, de

transport ou autres causés par une (des) pièce(s) défectueuse(s), une réparation,

un remplacement ou autre, ne seront pas couverts sous cette garantie, et la

Société n’assume aucune responsabilité pour ceux-ci. De plus, la Société ne

pourra être tenue responsable pour tous dommages fortuits ou indirects sauf

la ou prévu par la loi.

6. Toutes autres garanties, exprimées ou sous-entendues, en ce qui a trait au

produit, ses composants et accessiores, ou toutes obligations/responsabilités

de la part de la Société sont aux présentes expressment excluses.

7. La Société n’assume et n’autorise personne à assumer, en son nom, toutes

responsabilités en ce qui a trait à la vente de ce produit Majestic Fireplaces.

8. Les garanties, telles que décrites dans ce document, ne s’appliquent pas aux

compasants de cheminée ou aux autres accessoires non Majestic Fireplaces

utilisés conjointement pour l’installation de ce produit.

9. La Société n’encourrera aucune responsabilité pour . . .

a) Les refoulements de cheminées ou débordements causés par les conditions

environnementales comme par les arbres, les édiﬁces, les toits, les côteaux

ou les montagnes adjacents.

b) Une ventilation inadéquate ou une pression d’air négative causée par

des systèmes mécaniques comme les fournaises, les ventilateurs, les

sécheuses, etc.

10. Cette garantie est nulle si:

a) Le foyer a été utilisé dans une atmosphère contaminée par du chlore, du

ﬂuor ou tous autres produits chimiques.

b) Le foyer est assujetti à de longues périodes d’humidité ou de

condensation.

c) Des dommages sont causés au foyer, à la chambre de combustion. à

l’échangeur de chaleur ou aux autres composants par de l’eau ou par la

température qui est le résultat mais sans y être limité, d’une mauvaise

installation de cheminée/ventilation.

d) Toute altération, abus volontaire, accident ou mauvais usage du produit

annulera cette garantie.

PORTES EN VERRE & PIECES PLAQUEES LAITON

Les portes en verre ne sont pas garanties contre le bris causé par un mauvais

usage ou un accident.

Les pièces en laiton devraient être nettoyées qu’avec de l’essence de citron. Les

nettoyeurs de laiton ne peuvent pas être utilisés. La Société ne sera pas responsable

pour, et ne garantit pas les pièces en laiton qui sont endommagées par des conditions

chimiques externes ou de refoulement.

SI UN SERVICE SOUS GARANTIE EST REQUIS .

. .

1. Communiquez avec votre détaillant. Assurez-vous que vous avez votre garantie,

votre reçu de caisse ainsi que le numéro de modèle/série de votre produit

Majestic Fireplaces.

2. NE TENTEZ PAS D’EFFECTUER DES REPARATIONS

VOUS-MEME.

*Les foyers à gaz CFM Corporation portant ce scean

d’approbatic de la garantie spéciale sont couverts par

une garantie limitée à vie. Celle-ci inclue les brüleurs en

céramique Insta-Flame, le’échangeur de chaleur et la chambre

à combustion. Toutes les autres pièces sont couverte pour un an.

2695 Meadowvale Blvd.

Mississauga, ON L5N 8A3

*CFM Corporation products bearing this special Warranty

Seal of Approval carry a comprehensive Limited Lifetime

Warranty. This includes the Insta-Flame Ceramic Burners,

Heat Exchange System and Combustion Chamber. All

other parts are covered for one year.

2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3

800-668-5323 • www.cfmcorp.com

CFM Corporation

Majestic fireplaces Woodland UVLC24RP Installation And Operating Instructions Manual

Marque: Majestic fireplaces

Modèle: Woodland UVLC24RP

Taper: Installation And Operating Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Majestic fireplaces Woodland UVLC24RP

Majestic fireplaces Woodland UVLC24RP Installation And Operating Instructions Manual

Ce manuel convient également à

Majestic fireplaces Woodland UVLC24RP Installation And Operating Instructions Manual

dans d''autres langues

Autres documents