Zephyr AK7536CS Manuel utilisateur

WWW.ZEPHYRONLINE.COM

OCT20.0301

Airﬂow Control Technology

TM

C

Tempest II

AK7500CS, AK7536CS, AK7542CS,

AK7548CS, AK7554CS

EN Use, Care, and Installation Guide

FR Guide d’utilisation, d’entretien et d’installation

2

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

3

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Contents

Page

Safety Information ............................................................................ 4-9

Types of Safety Warnings ................................................................... 4

General Safety ..................................................................................5-8

Operation ........................................................................................... 8

Electrical Requirements .....................................................................8-9

Federal Communication Commission Interface Statement ................. 9

List of Materials .................................................................................. 10

Installation Instructions ....................................................................11-24

Ducting Calculation Sheet .................................................................... 11

Mounting Height, Clearance, & Ducting .......................................... 12-13

Ducting Options .................................................................................14

Hood Speciﬁcations ............................................................................15

Electrical Supply .................................................................................16

Cable Lock .........................................................................................16

Mounting the Hood ...........................................................................17-18

Horizontal Ducting Conversion ........................................................ 19-21

PBD-1200A Dual Blower Vertical Ducting .........................................22-23

PBD-1200A Dual Blower Horizontal Ducting ....................................... 24

Features & Controls ......................................................................... 25-29

Touch Controls ................................................................................25-27

Optional RF Remote Control ............................................................28-29

Maintenance ................................................................................... 30-32

Hood & Filter Cleaning .....................................................................30-31

LumiLight LED ................................................................................... 32

ACT™ Conversion ............................................................................ 33-35

Airﬂow Control Technology (ACT™) ................................................... 33

Enabling ACT™ ................................................................................34-35

Wiring Diagram ............................................................................... 36-37

Troubleshooting............................................................................... 38-39

List of Parts & Accessories ..................................................................40

Notes ................................................................................................41-42

Limited Warranty ...............................................................................43

Product Registration ........................................................................... 44

4

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Safety Information

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual for your appliance. Always read

and obey all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can cause severe

bodily injury or death. All safety messages will follow the Safety Alert Symbol and either the words

“DANGER” “WARNING” or “CAUTION”

DANGER

WARNING

CAUTION

Danger means that failure to heed this safety

statement may result in severe injury or death.

Warning means that failure to heed this safety

statement may result in extensive product damage,

serious personal injury, or death.

Caution means that failure to heed this safety

statement may result in minor or moderate

personal injury, property or equipment damage.

5

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

To reduce the risk of ﬁre or electric shock, do not use this fan

with any solid-state control device.

WARNING

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer.

b) Before servicing or cleaning unit, switch power o at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to

the service panel.

WARNING

General Safety

For General Ventilating Use Only. Do Not Use To Exhaust

Hazardous Or Explosive Materials And Vapors. Take care

when using cleaning agents or detergents. Suitable for use in

household cooking area.

CAUTION

6

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Safety Information

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when ﬂambeing food. (i.e. Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING

WARNING - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING:

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or metal tray, then turn o the burner. BE

CAREFUL TO PREVENT BURNS. If the ﬂames do not go out immediately, EVACUATE AND CALL THE

FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN – You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class ABC extinguisher, and you already know how to operate it.

2) The ﬁre is small and contained in the area where it started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit

Based on “Kitchen Firesafety Tips” published by NFPA.

WARNING

7

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

READ AND SAVE THESE INSTRUCTIONS

WARNING

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with all

applicable codes and standards, including ﬁre-rated construction.

b) Sucient air is needed for proper combustion and exhausting of gases through the ﬂue (chimney)

of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s

guideline and safety standards such as those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden

utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be marked as appropriate for the

application and be connected to a GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING

8

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Safety Information

READ AND SAVE THESE INSTRUCTIONS

Ź To reduce risk of ﬁre and to properly exhaust air outside, do not vent exhaust air into spaces within

walls, ceilings, attics, crawl spaces, or garages.

CAUTION

Operation

Ź Always leave safety grilles and ﬁlters in place. Without these components, operating blowers could

catch onto hair, ﬁngers and loose clothing.

Ź The manufacturer declines all responsibility in the event of failure to observe the instructions given

here for installation, maintenance and suitable use of the product. The manufacturer further

declines all responsibility for injury due to negligence and the warranty of the unit automatically

expires due to improper maintenance.

NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

Electrical Requirements

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility to be aware of these below:

Ź To contact a qualiﬁed electrical installer.

Ź To assure that the electrical installation is adequate and in conformance with National Electrical

Code, ANSI/NFPA 70 latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1

and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

Ź If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician

determine that the ground path is adequate.

Ź Do not ground to a gas pipe.

Ź Check with a qualiﬁed electrician if you are not sure the range hood is properly grounded.

Ź Do not have a fuse in the neutral or ground circuit.

9

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

READ AND SAVE THESE INSTRUCTIONS

Prop. 65 Warning for California Residents: This product may

contain chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Ź This appliance requires a 120V 60Hz electrical supply and connected to an individual properly

grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring

must be 2 wire with ground. Please also refer to Electrical Diagram on product.

Ź A cable locking connector (not supplied) might also be required by local codes. Check with local

requirements, purchase and install appropriate connector if necessary.

* National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

Federal Communication Commission Interface Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the interference by one

of the following measures:

Ź Reorient or relocate the receiving antenna.

Ź Increase the separation between the equipment and receiver.

Ź Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

Ź Consult the dealer or an experienced radio/TV technician for help.

10

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

List of Materials

#6 x 1” (4 )

#6 x 1-1/2” (4 )

#6 x 2” (4 )

M3.5 x 8 (8)

Wire Caps (3)

3/16 x 3/8 (4)

Parts Not Supplied

Ducting, conduit and all installation tools

Cable locking connector (if required by local codes)

Dual blower kit (PBD-1200A)

Duct cover accessory

Wood board to hang hood (WxDxH)

AK7500CS: 27” x 1/2” x 4”

AK7536CS: 33” x 1/2” x 4”

AK7542CS: 39” x 1/2” x 4”

AK7548CS: 45” x 1/2” x 4”

AK7554CS: 51” x 1/2” x 4”

Parts Supplied

Quantity Part

1Hood

2 Pro bae ﬁlters (AK7500CS, AK7536CS, AK7542CS)

3 Pro bae ﬁlters (AK7548CS & AK7554CS)

2 LumiLight LED, 6W (pre-installed)

4 LumiLight LED, 6W (pre-installed) (only AK7548CS & AK7554CS)

1 8” round starting collar

1 Rectangular starting collar (for single horizontal ducting)

1 Top cover plate (for horizontal ducting)

1 Hardware package

11

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Duct pieces

To t a l

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

To t a l

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 150 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

ﬂat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Ducting Calculation Sheet

12

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Installation Instructions

Mounting Height, Clearance, & Ducting

24” min.

36” max.

36”

13

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Mounting Height, Clearance, & Ducting

A minimum of 8” round must be used to maintain maximum air ﬂow eciency for single blower and

10” round duct for dual blower for both horizontal and vertical ducting.

A 3-1/4” x 10” rectangular duct may also be used for single blowers for horizontal ducting

Always use rigid type metal ducts only. Flexible ducts could restrict air ﬂow by up to 50%.

Also use calculation (on page 11) to compute total available duct run when using elbows, transitions

and caps.

ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required,

increase duct size.

If turns or transitions are required; install as far away from hood duct output and as far apart,

between the two as possible.

Minimum mount height between range top to hood bottom should be no less than 24”.

Maximum mount height should be no higher than 36”.

It is important to install the hood at the proper mounting height. Hoods mounted too low could result

in heat damage and ﬁre hazard; while hoods mounted too high will be hard to reach and will lose its

performance and eciency.

If available, also refer range manufacturer’s height clearance requirements and recommended hood

mounting height above range.

For shipment and installation damages:

Ź Please fully inspect unit for damage before installation.

Ź If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or

replacement.

Ź If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

Ź If the unit is damaged by the installer (if other than the customer), repair of replacement must be

made by arrangement between customer and installer.

14

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Installation Instructions

Ducting Options

Ź Use single wall rigid metal ductwork only.

Ź Fasten all connections with sheet metal screws and tape all joints w/ certiﬁed Silver Tape or Duct

Tape.

Fire Hazard: NEVER exhaust air or terminate ductwork into

spaces between walls, crawl spaces, ceilings, attics, or garages.

All exhaust must be ducted to the outside, unless using the

recirculating option.

WARNING

Sot or crawl space

Roof Pitch w/

Flashing & Cap

Rear Ducting

Side wall cap

w/ gravity damper

15

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Ů

Top View

Side View

Back View

Ducting & Electrical Dimensions

12”

24”

4”

18”

8-9/16”

1-3/4”

1-1/16”

11-9/16”

6”

**7-7/8”

or

***10-3/8”

**9-1/2”

or

***14-3/16”

2-3/4”

**7-7/8”

or

***9-15/16”

R 9/16”

**7-7/8”

or

***10-3/8”

**1-15/16”

or

***4-5/16”

11-9/16”

10-3/4”

*3-3/16”

**7-7/8“

***10-3/8”

*9-7/8”

**9-1/2”

***14-3/16”

**7-7/8”

or

***9-15/16”

* Single Blower Rect. Ducting Dimension

** Single Blower Round Ducting Dimension

*** Dual Blower Dimension

1-11/16”

29-7/8” (30”)

35-7/8” (36”)

41-7/8“ (42”)

47-7/8” (48”)

53-7/8” (54”)

C/L

Back View

Mounting Dimensions

16-7/8”

16-1/8”

13-5/8”

1-11/16”

3-5/16”

21-1/4”

27-3/8” (36“ & 42”), 35-1/4” (48” & 54”)

5-5/16”

16

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Installation Instructions

Electrical Supply

Electrical wiring must be done by qualiﬁed person(s) in

accordance with all applicable codes and standards. Turn o

electrical power at service entrance before wiring.

WARNING

For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not

use extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and ordinances.

This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly

grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring

must be 2 wire w/ ground. Please also refer to the Electrical Diagram labeled on product.

Cable Lock

A cable locking connector (not supplied) might be required by local codes. Check with local

requirements and codes, purchase and install appropriate connector if necessary. (FIG. A)

Cable Lock

FIG. A

17

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Mounting the Hood

FIG. B

C/L

A

B

16-7/8”

min

24”

4”

wood board

At least two installers are required due to the

weight and size of the hood.

CAUTION

1. Select preferred ducting application (vertical or

horizontal) and prepare hood. Refer to page 11

for single blower horizontal ducting, page 13 for

dual blower vertical ducting or page 14 for dual

blower horizontal ducting.

2. Plum and mark center line on wall.

3. Choose desired height above cooking surface

(24” min). Level and mark hood bottom, line A

(FIG. B)

4. Level and mark top of wood board, line B (FIG.

B) 16-7/8” from line A.

5. Mark center line of wood board. Center and

align top of board with line B. Secure wood

board to studs using (4) #6 wood screws. Wood

Board Dimensions: (W x D x H)

AK7500CS - 27” x 1/2” x 4”

AK7536CS - 33” x 1/2” x 4”

AK7542CS - 39” x 1/2” x 4”

AK7548CS - 45” x 1/2” x 4”

AK7554CS - 51” x 1/2” x 4”

6. Prepare duct pipe and duct cut outs in upper

cabinet if needed or wall If horizontally ducting

hood. Refer to hood speciﬁcations on page 15

for dimensions.

18

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Installation Instructions

Mounting the Hood

7. Prepare electrical wiring and electrical cut outs in upper cabinet if needed or wall if horizontal

electrical hook up is required. Refer to hood speciﬁcations on page 15 for dimensions.

8. Mount hood onto wood board and secure using (4) #6 wood screws.

9. Further secure hood onto wall through lower body screw holes by (2) #6 wood screws. See

dimensions in FIG. C.

10. Install electrical.

11. Install duct work and seal with certiﬁed aluminum duct tape.

12. Power up hood and check for leaks around duct tape.

13. Install bae ﬁlters.

FIG. C

16-7/8”

16-1/8”

13-5/8”

1-11/16”

3-5/16”

21-1/4”

27-3/8” (36“ & 42”), 35-1/4” (48” & 54”)

5-5/16”

19

Tempest II Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Horizontal Ducting Conversion

This range hood is equipped standard with a 8” round vertical duct option. To convert from 8” round

vertical to 8” round horizontal ducting or 3-1/4” x 10” rectangular horizontal ducting please following

the instructions below.

C

B

1. Disconnect blower plug.

2. Remove (4) screws from interior

of hood body attaching single

blower plate to top of hood body.

Remove single blower and single

blower plate.

3. Knock out rear plate B for rear

rectangular rear ducting or plate

C for 8 inch round rear ducting.

20

Tempest II Use, Care, and Installation Guide

TEMPEST II

UNDERCABINET

PRO

Installation Instructions

Horizontal Ducting Conversion

4. Remove (4) screws attaching

blower to blower plate. Turn

blower 180 degrees and reattach

to blower plate.

5. Position single blower with single

blower plate as shown. Be sure to

tuck back of single blower plate

into tabs at back of hood. Secure

single blower plate to back of

hood using (4) screws removed

from step 2.

6. Attach 8” round duct collar or

3-1/4” x 10” rectangular duct

collar to back of hood body using

(4) M3.5 x 8 screws.

La page charge ...

Zephyr AK7536CS Manuel utilisateur

Zephyr AK7536CS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents