Empava EPV-30RH05 Manuel utilisateur

Marque: Empava

Modèle: EPV-30RH05

Taper: Manuel utilisateur

EMPAVA APPLIANCE INC.

Add: 15253 Don Julian Rd, City of Industry, CA 91745

Tel: 888-682-8882

www.empava.com

RANGE HOOD

Installation and Operation

Manual

TECHNICAL CHARACTERISTICS

Dear consumer,

Thanks for your purchase of our range hood and we hope we can fully

satisfy all of your needs. Please read the entire instructions carefully

before proceeding to obtain the best results of operation the range hood.

Please note that this product is marked with symbol:

According to Waste of Electrical Electron Equipment

(WEEE) directive, WEEE should be separately collected

and treated. If at any time in future you need to dispose of

this product, please do NOT dispose of this product with

household waste. Please send this product to WEEE

collecting points where available.

Model No.: EMPV-30RH05 EMPV-30RH06

Total power: 204W

Motor power: 200W

Led Light: 2x2W

Voltage: 120V

Frequency: 60Hz

Filter: Steel Baffle filter

Control: Touch Control

25.98"-37.6"

06"

10.43"

18.9"

29.5"

/35

EMPV-30RH05 EMPV-30RH06

34.94"-36.61"

5.2

26"

MAIN PARTS NAME

Hook

Inner duct cover

Outer duct cover

Vent pipe

Blower box

Filter

Hook

Inner duct cover

Outer duct cover

Vent pipe

Blower box

Air outlet

Glass

Filter

EMPV-30RH05

EMPV-30RH06

INSTALLATION REQUIREMENT

1. Do not install the range hood where there are many doors ro

windows in order to avoid eﬀecting the exhaust eﬃciency of the

hood that caused by air convection. (ﬁg.1)

2. Install the range hood right above the cooking surface. The

recommended distance between the cooking surface and the lower

edge of the range hood is minimum 27.56" to maximum 31.5".

(Fig.2) 3. In order to get the best performance, do not extend the

vent pipe too long, and try to make the bend of the vent pipe less

and straight, make sure the vent pipe connection is ﬁrm and air

proof. (Fig.3)

4. After hanging the range hood on the wall, make sure the hood is

level and vertical. (Fig.4)

5. The air Outlet is not allowed to connect to chimney ﬂues or

combustion gas ducts. The air outlet should under no circumstances

be connected to ventilation ducts for room in which fuel-burning

ppliances are installed.

INSTA L L AT I O N P R O C E D U R E S

SAFETY WARNING

HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR

PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE

ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.

Vent pipe

Air outlet

Step 1:

Put the vent pipe to the air outlet like

this picture. And use one ST3.9x10

screw to fix the vent pipe.

Step 2:

Matching the hook to the holes of

the inner duct cover and fix it well

with M4 screws.

Step 3:

Insert the inner duct cover into the

outer duct cover.

Step 4:

Matching the holes of the outer duct

cover and blower box, fix the outer

duct cover to the blower box using

8pcs M4*10 screw provided with the

fixing tool as the direction of the

illustrated.

5x50

Metal Screw

Expanding Tube

5x50

Wood Screw

Expanding Tube

Metal Screw

5x50

Expanding tube

Hook

200

367

Step 6:

Hang the entire hood onto the hook,

ensure the hood is level and vertical.

Step 7:

1. Draw the inner duct cover up to the

suitable height, mark on the wall two

keyhole of the outer duct cover bracket

with pen .

2. Put down the inner duct cover gently,

drill the keyholes in 75-85 mm depth on

the horizontal level using 10mm drill.

3. Press the expanding tube provided into

the holes.

4. Matching the inner duct cover with the

holes, tighten the inner duct cover with

two 5x50 metal screw provided.

Step 8:

Extend the air outlet of the exhaust pipe

out-of-door. Try to make the bend of the

exhaust pipe is no more than 120°.

Step5:

A ccording to the size of hook key holes.

10mm in diameter and 75~85mm in depth.

Press the 3 expanding tube provided into

the holes. Fix the hook using the 5x50

metal screw provided.

Then insert three M5X50 screws to A and B

And C holes to fix the hook on the wall

Drill 3 holes in level in the wall with

steadily.

OPERATING INSTRUCTION

1).Electronic Switch

A. Light

B. Time

C. Speed down

D. Speed up

E. Max speed

F. On /off

A B C D E F

2). Touch Control

A: Light

Press the button once to turn on the light, press again to turn off.

B. Timer

In standby mode, press 3 seconds, to enter into time setting mode,

Press “+” set hour (0-23 circle set) and press “–” set minute(0-59),

No operation within 5 seconds for automatically confirmation. When

working, press once to enter into delay turn off mode for 3 minutes.

Press again to increase delay turn off time from 3-59 minutes.

No operation for 5 seconds, the hood will be turn off in 3 minutes.

Press again to turn off immediately.

C.- In standby mode, press to change to speed 1.

D.+ In standby mode, press to change to speed 2 & 3.

E. Speeds

In standby mode, press once to start high speed.

F. Power on/off

In standby mode, press once to turn on all buttons. Press again to

turn off the power. When working, press once to start delay turn off

3 minutes. In delay turn off mode, press again to stop delay turn off.

MA I N TE N A NC E

CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING

WHILE THE FAN IS OPERATING.

FOR THE OPTIMAL LEVEL FO OPERATION, CLEAN THE RANGE

HOOD SURFACE, AN AND ALUMINUM FILTER REGULARLY.

1. Use only mild soap or detergent solutions to clean the range hood

surface. Dry surfaces using soft cloth.

2. Using a stainless steel cleaner to bring the

glow back into a stainless ﬁnish.

3. Clean the ﬁlter once a week or according to use

status. Press the buckle of the ﬁlter slightly,

take oﬀ the ﬁlter and put it into warm soapy

water using mild detergent, wipe the ﬁlter with

soft brush. Replace the ﬁlter after it’s dry.

4. Clean the motor fan and other inside parts once half year or according

to use status by QUALIFIED PERSON.

5. DO NOT clean motor with water or other liquid.

To replace Led light (Pic.1)

Сaution: LED light can not replace a new bulb, just replace a new

LED light assembly.

Make sure all the control switches are oﬀ, and the range hood is

unplugged! Please follow below instructions:

1. Take out the ﬁlters, and cut oﬀ the wire connection of the light.

2. Press the spring according to the arrow direction, then you can take

oﬀ the LED light.

3. You can replace a new LED assembly no more than rating.

4. Then put the light assembly to the hood in reverse direction. Connect

the wire of the lamp.

5. Fit on the ﬁlters.

TO R E P L A C E L I G H T

To replace the LED light

should be undertaken by a

qualified electrician or a

competent person. Always

use the light no more

than rating.

Do not connect the air

outlet to chimney ﬂues or

combustion gas ducts

Do not leave naked

ﬂames under the hood

In case of any damage

to power cable, replace

the broken cable with a

new one by qualiﬁed

person.

Do clean the hood

correctly in accordance

with instruction stated or it

might cause the possibility

of ﬁre accident

WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when ﬂambeing food (i.e.Crepes Suzette,

Cherries Jubilee, Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING: SMOTHER FLAMES with a close-ﬁtting lid,

cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.

If the ﬂames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN – You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class ABC extinguisher, and you already know how to operate it.

2) The ﬁre is small and contained in the area where it started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit.

WARNING: TO PROVIDE PROTECTION AGAINST ELECTRIC SHOCK, CONNECT TO

PROPERLY GROUNDED OUTLETS ONLY.

A UTILISER SEULEMENT AVEC UNE TROUSSE DE RACCORDEMENT DE CORDON DE

HOTTE VÉRIFIÉE ET APPROUVÉE POUR EMPLOI AVEC CE MODÈLE DE HOTTE.

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any

Solid-State Speed Control Device. AVERTISSEMENT : NE CONVIENT PAS A DES

REGULATEURS DE VITESSE A SEMI-CONDUCTEURS.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding

reduces the risk of electric shock by providing an escape wire for the electric current. This

appliance is equipped with a cord having a grounding wire with a grounding plug. The plug

must be plugged into an outlet that is properly installed and grounded.

WARNING – Improper grounding can result in a risk of electric shock.

Consult a qualiﬁed electrician if the grounding instructions are not completely understood,

or if doubt exists as to whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is too short, have a qualiﬁed electrician

install an outlet near the appliance

CONSIGNES DE MISE A LA TERRE

Cet appareil doit être mis à la terre. En cas de court-circuit, le ﬁl de mise à la terre limite le

risqué de choc électrique parce qu’il assure le retour du courant à la terre. L’appareil est

livré avec un cordon muni d’un ﬁl de terre et d’une ﬁche de mise à la terre, qui doit être

branchée sur une prise mise à la terre correctement installée.

AVERTISSEMENT — Une mise à la terre incorrecte peut entraîner des risques de choc

électrique. Consulter un électricien compétent en cas de doute sur ces consignes de mise

à la terre ou en cas d’incertitude concernant la mise à la terre correcte du circuit sur lequel

l’appareil est branché.

Ne pas utiliser de cordon de rallonge. Si le cordon d’alimentation est trop court, faire installer

une prise par un électricien compétent à proximité de l’appareil.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.

TROUBLE SHOOTING

CAUTION: Disconnect the power supply before servicing.

Status

Cause and Method of Repairing

Tools required

No power

Check circuit breakers

If the power supply is damaged,

please call for a qualiﬁed person

Philips

Screwdriver

Philips

Screwdriver

Philips

Screwdriver

Philips

Screwdriver

Philips

Screwdriver

Philips

Screwdriver

The motor

does not run

a).The motor is broken, replace motor.

b). The switch control is broken, replace switch.

c). The capacitor is broken, replace capacitor.

Body

vibration

a).The installation is not correct, check it and

make sure the hood is level.

b). The fan is broken, replace motor assembly.

c). The fan motor was not properly installed,

check and make sure it is ﬁrmly installed.

Noise

vibration

Something dropped into the blower, check

and clean blower.

Weak

suction

a). The distance from the range hood to cooking

surface is too far, make sure the distance

between bottom of the hood to cooking surface

is minimum 24" to maximum 27".

b). Windows, doors and drafts can eﬀect the

performance of the range hood.

c). There are other air conditions eﬀecting the

vent pipe, make sure lower vent pipe’s exit

is in a downward direction.

d). The running rate of the motor slows down,

replace the motor or capacitor.

If the range hood is near the window,

the best solution is to protect the back of the

range hood from draft caused by a window or

door.

Light does

not work

Replace LED lamp.

Empava EPV-30RH05 Manuel utilisateur

Marque: Empava

Modèle: EPV-30RH05

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Empava EPV-30RH05 User manual

Empava EPV-30RH05 Manuel utilisateur

Empava EPV-30RH05 Manuel utilisateur

dans d''autres langues

Autres documents