Johnson Controls FX-WRZSST-110 Guide d'installation
- Taper
- Guide d'installation
FX-WRZSST-110 Wireless Sensing System Tool Installation Instructions 1
Applications
The FX-WRZSST-110 Wireless Sensing System Tool is
a lightweight, portable, wireless receiver designed to
receive wireless Radio Frequency (RF) data
transmissions from Johnson Controls® FX-WRZ
Series Wireless Room Sensors in One-to-One sensing
system site survey applications. The FX-WRZSST-110
Tool also serves as a signal test receiver or site survey
tool prior to installing an FX-ZFR Series Wireless Field
Bus System.
Prior to installation, use the FX-WRZSST-110 Tool, to
verify the optimum locations for FX-WRZ Series
Sensors and the FX-WRZ7850 Receiver in
One-to-One wireless room sensing systems. You can
also use the FX-WRZSST-110 Tool to verify the
optimum locations for Johnson Controls FX-ZFR1810
Coordinators, FX-ZFR1811 Routers, and
FX-WRZ Series Sensors in wireless field bus
applications.
North American Emissions Compliance
United States
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when this equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case
the user will be required to correct the interference
at his/her own expense.
RF Transmitters: Compliance Statement
(Part 15.19)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
,
an
d
2. This device must accept any interference
received, including interference that may cause
undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
FX-WRZSST-110 Wireless Sensing System Tool
Installation Instructions
FX-WRZSST-110
Part No. 24-10563-20, Rev. —
Issued April 12, 2011
FX-WRZSST-110 Wireless Sensing System Tool Installation Instructions2
Canada
Installation
Transport the FX-WRZSST-110 Wireless Sensing
System Tool in the original container to minimize
vibration and shock damage to the receiver.
Verify that all the parts shipped with the receiver:
• one FX-WRZ7850 Receiver with two magnets
attached
• one battery pack with two magnets attached
• two AA alkaline batteries
• one installation instructions sheet
Do not drop the receiver or subject it to physical shock.
Mounting
To mount the receiver:
Note: Check that the power switches on the
FX-WRZ7850 Receiver and FX-WRZ Series Sensor
are set to OFF before proceeding.
1. Set the TRANSMITTER ID and AREA DIP
switches on the FX-WRZ7850 Receiver and the
FX-WRZ Series Sensor to the same address.
Refer to the One-to-One Wireless Sensing System
Technical Bulletin (LIT-12011663) for more details.
2. Install the batteries into the battery pack.
3. Connect the battery pack wire harness to the
two-pin connector located under the
TRANSMITTER ID DIP switches on the back of
the FX-WRZ7850 Receiver.
Note: Connecting the battery pack to the receiver
transforms the FX-WRZ7850 Receiver into the
FX-WRZSST Tool.
4. Turn the battery pack switch to ON.
5. For a One-to-One wireless room sensing system,
place the FX-WRZSST-110 Tool in the area where
the FX-WRZ7850 Receiver is to be located, and
place the FX-WRZ Series Sensor in the area
where you intend to mount the sensor.
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte
toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
RF Transmitters: Industry Canada Statements
The term IC before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.
This device has been designed to operate with an
antenna having a maximum gain of 2 dB. Antenna
having a higher gain is strictly prohibited per
regulations of Industry Canada. The required
antenna impedance is 50 ohms.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen
that the Equivalent Isotropically Radiated Power
(EIRP) is not more than that required for successful
communication.
Le terme « IC » précédant le numéro d'accréditation/
inscription signifie simplement que le produit est
conforme aux spécifications techniques d'Industry
Canada.
Cet appareil a été conçu pour fonctionner avec une
antenne d'un gain maximum de 2 dBi. En application
des réglementations d'Industry Canada, l'utilisation
d'une antenne de gain supérieur est strictement
interdite. L'impédance d'antenne requise est de
50 ohms.
Pour réduire les interférences radio potentielles
avec les dispositifs d'autres utilisateurs, le type
d'antenne et son gain doivent être choisis de façon à
ce que la Puissance Isotrope Rayonnée Équivalente
(PIRE) ne soit pas supérieure à la puissance
nécessaire pour une bonne communication.
IMPORTANT: If there are other wireless mesh
networks or One-to-One wireless room sensing
systems in the area, ensure that the PAN OFFSET
address of the FX-WRZ7850 Receiver and
FX-WRZ Series Sensor (set by the TRANSMITTER
ID and AREA DIP Switches) is different from the
PAN OFFSET address of those wireless mesh
networks or One-to-One wireless room sensing
systems.
FX-WRZSST-110 Wireless Sensing System Tool Installation Instructions 3
Note: If an FX-ZFR1811 Wireless Field Bus Router is
used in the final installation to extend the operating
range, place the FX-WRZSST-110 Tool in the location
where the FX-ZFR1811 Router is to be located. Use
the FX-WRZ Series Sensor to verify the intended
sensor location, then use the FX-WRZ Series Sensor
to stimulate and verify the intended FX-WRZ7850
Receiver location.
For an FX-ZFR Series Wireless Field Bus System,
place the FX-WRZ Series Sensor in the desired
location for an FX-ZFR1811 Router, and place the
FX-WRZSST-110 Tool in the desired location for an
FX-ZFR1811 Router or FX-ZFR1810 Coordinator.
6. Turn on the power switch of the test FX-WRZ
Series Sensor and allow it to establish
communication with the FX-WRZSST-110 Tool.
When communication is established, the
Light-Emitting Diode (LED) showing RF signal
strength on the FX-WRZSST-110 Tool blinks.
If communication is not established within
15 seconds, press the manual occupancy override
button on the FX-WRZ Series Sensor to force
another communication attempt.
7. After the FX-WRZ Series Sensor establishes
communication with the FX-WRZSST-110 Tool,
press the manual occupancy override button for
5 seconds and release to force the sensor into
Rapid Transmit Mode (RTM).
8. Hold the FX-WRZSST-110 Tool in the desired
location and record the number of times the
RF signal strength LED blinks over the course of
10 seconds.
If the RF signal strength is weaker than Good,
move the location of either device until an Excellent
or Good RF signal strength is indicated.
Move on to the next location, and repeat Step 1
through Step 9 as necessary.
9. When testing is finished, turn off the battery switch
on the FX-WRZSST-110 Tool and turn off the
power switch on the test FX-WRZ Series Sensor.
Operation
Wireless Signal Strength
The RF signal strength LED indicates the strength of
the RF wireless signal between the sensor and its
associated sensing system receiver, expressed as
Excellent, Good, or Weak. The FX-WRZSST-110 Tool
has an RF signal strength LED that blinks off one, two,
or three times for every RF transmission to indicate the
RF signal strength between the sensor and the tool, or
the router/coordinator and the tool. See Table 1.
Rapid Transmit Mode (RTM) and RF Signal
Strength LEDs
Normally, the sensor transmits every 60 seconds;
however, pressing the manual occupancy override
button on the FX-WRZ Series Sensor for 5 seconds
and then releasing it forces the sensor into RTM. In
RTM, an FX-WRZ Series Sensor sends an RF data
transmission once every 10 seconds. The sensor
remains in RTM for up to 30 RF transmissions. After
each RF transmission, the RF signal strength LED of
the sensor flashes (LED off to on) to indicate the RF
signal strength between the sensor and FX-
WRZSST-110 Tool. The
FX-WRZSST-110 Tool blinks (LED on to off) to indicate
the wireless RF signal strength.
Table 1: Wireless RF Signal Strength
Number of LED Blinks RF Signal Strength
3 Excellent
2 Good
1 Weak
0 None
Published in U.S.A. www.johnsoncontrols.com
FX-WRZSST-110 Wireless Sensing System Tool Installation Instructions4
Johnson Controls® is a registered trademark of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. © 2011 Johnson Controls, Inc.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Repair Information
If the FX-WRZSST-110 Wireless Sensing System Tool
fails to operate within its specifications, replace the
unit. For a replacement FX-WRZSST-110 Tool, contact
the nearest Johnson Controls representative.
Two AA alkaline batteries are supplied with the
FX-WRZSST-110 Wireless Sensing System Tool.
Replace the batteries with high-quality AA alkaline
batteries as necessary, ensuring that the batteries are
installed in the proper polarity. Both batteries should be
replaced at the same time.
Note: Batteries removed from this device must be
recycled or disposed of in accordance with local,
national, and regional regulations. Only certified
technicians or qualified building maintenance
personnel should service Johnson Controls products.
Lithium batteries with a maximum cell voltage of
1.5 volts can be substituted to extend the period
between battery replacement. Do not mix lithium and
alkaline batteries in this device.
-
1
-
2
-
3
-
4
Johnson Controls FX-WRZSST-110 Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Johnson Controls WRZ-SST-110 Guide d'installation
-
-
-
-
-
-
-
-
-