ADLINK Technology CSA-7400 Guide de démarrage rapide

Taper
Guide de démarrage rapide
Leading EDGE COMPUTING
CSA-7400
4U Rackmount Network Appliance
with Dual Intel® Xeon® Processor E5-2600 v3/v4 &
Dual Redundant Intel® FM10840
Quick Start Guide
Manual Revision: 1.1
Revision Date: November 5, 2018
Part No.: 50-40349-5010
2
CSA-7400 QSG
Preface
Copyright 2018 ADLINK Technology, Inc.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or other
means in any form without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order to improve
reliability, design, and function and does not represent a commitment on the part of the
manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the European
Union's Restriction of Hazardous Substances (RoHS) directive and
Waste Electrical and Electronic Equipment (WEEE) directive.
Environmental protection is a top priority for ADLINK. We have enforced
measures to ensure that our products, manufacturing processes,
components, and raw materials have as little impact on the environment
as possible. When products are at their end of life, our customers are
encouraged to dispose of them in accordance with the product disposal and/or recovery
programs prescribed by their nation or company.
Battery Labels (for products with battery)
廢電池請回收
California Proposition 65 Warning
WARNING: This product can expose you to chemicals including acrylamide,
arsenic, benzene, cadmium, Tris(1,3-dichloro-2-propyl)phosphate (TDCPP), 1,4-
Dioxane, formaldehyde, lead, DEHP, styrene, DINP, BBP, PVC, and vinyl materials,
which are known to the State of California to cause cancer, and acrylamide, benzene,
cadmium, lead, mercury, phthalates, toluene, DEHP, DIDP, DnHP, DBP, BBP, PVC, and vinyl
materials, which are known to the State of California to cause birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
Trademarks
Product names mentioned herein are used for identification purposes only and may be
trademarks and/or registered trademarks of their respective companies.
3
CSA-7400 QSG
Revision History
Revision Release Date Description of Change(s)
1.0 2018-03-22 Initial release
1.1 2018-11-05 Update switch sled login procedure; add
rackmount warnings
4
CSA-7400 QSG
Table of Contents
Preface .................................................................................................................................. 2
List of Figures....................................................................................................................... 6
1 Overview .......................................................................................................................... 7
1.1 Introduction..............................................................................................................................7
1.2 Mechanical Overview...............................................................................................................8
1.2.1 Front Panel........................................................................................................................8
1.2.2 Rear Panel.........................................................................................................................8
1.3 Chassis Module List.................................................................................................................9
1.4 Package Contents....................................................................................................................9
2 Preparation..................................................................................................................... 10
2.1 About This Guide ...................................................................................................................10
2.2 Required Equipment for Initial Setup......................................................................................11
3 Getting Started............................................................................................................... 12
3.1 Installing a SATA Drive...........................................................................................................12
3.2 Connecting VGA cable to the MXN-3610...............................................................................14
3.3 Assembling the CSA-7400.....................................................................................................15
3.3.1 Inserting and Removing the MCN-2600T CPU Sled........................................................15
3.3.2 Inserting and Removing the MXN-3610 Switch Sled.......................................................19
3.4 MCN-2600T I/O Ports ............................................................................................................22
3.5 MXN-3610 I/O Ports...............................................................................................................23
3.6 Connecting Power Cords to the CSA-7400 ...........................................................................24
4 Powering Up for the First Time .................................................................................... 25
4.1 Power-Up Behavior................................................................................................................25
4.2 Health/Status Indicators and Buttons.....................................................................................26
5 BIOS Setup..................................................................................................................... 27
5.1 MXN-3610 BIOS Configuration..............................................................................................27
5.2 MCN-2600T BIOS Configuration............................................................................................28
6 Network Configuration.................................................................................................. 30
6.1 MXN-3610 System IP Setup..................................................................................................30
6.2 CMM IP configuration............................................................................................................. 31
7 Running the CSA-7400 Platform .................................................................................. 32
7.1 Login to the MXN-3610 Switch ..............................................................................................32
7.1.1 Login Via Serial Port........................................................................................................32
7.1.2 Local Login ......................................................................................................................35
7.1.3 Via Network Port..............................................................................................................37
7.2 MXN-3610 OS Version Check ...............................................................................................38
7.3 Login to the MXN-3610 CMM Locally....................................................................................39
7.3.1 Login to the CMM Via Serial Port ....................................................................................39
7.3.2 Login to the MXN-3610 CMM via LAN Port.....................................................................41
7.4 Checking the MXN-3610 CMM Firmware Version .................................................................42
7.5 Running MCN-2600T System................................................................................................43
8 PacketManager on the MXN-3610 ................................................................................ 44
8.1 Check PacketManager Installation Version............................................................................44
5
CSA-7400 QSG
8.2 Command Line Interface and Configure Mode......................................................................45
8.3 Get Help and Check Version..................................................................................................46
8.4 Switch Management ..............................................................................................................48
8.4.1 Port Configuration............................................................................................................49
8.4.2 VLAN Configuration.........................................................................................................59
8.4.3 ACL Configuration............................................................................................................61
8.4.4 IP Configuration...............................................................................................................68
9 Hot-Swapping................................................................................................................ 72
9.1 Hot-Swapping the MCN-2600T Sled......................................................................................72
9.2 Hot-Swapping the MXN-3610 Sled........................................................................................72
Safety Instructions............................................................................................................. 73
Consignes de Sécurité Importantes ................................................................................. 75
Getting Service................................................................................................................... 77
6
CSA-7400 QSG
List of Figures
Figure 1: Required Equipment for Initial Setup......................................................................11
Figure 2: MXN-3610 VGA Connector Location..................................................................... 14
Figure 3: Connecting the VGA Cable.................................................................................... 14
Figure 4: CSA-7400 System................................................................................................. 15
Figure 5: MXN-3610 VGA Cable Routing ............................................................................. 21
Figure 7: MCN-2600T I/O Ports............................................................................................ 22
Figure 6: MXN-3610 I/O Ports.............................................................................................. 23
Figure 8: Connecting Power Cords....................................................................................... 24
Figure 9: CSA-7400 Status LEDS......................................................................................... 26
Figure 10: Setting BIOS Display Mode................................................................................. 27
Figure 11: MXN-3610 BIOS.................................................................................................. 28
Figure 12: MCN-2600T BIOS Setup Menu........................................................................... 29
Figure 13: COMe Module Network Default Mode................................................................. 30
Figure 14: CMM Network Default Mode ............................................................................... 31
Figure 15: Connecting USB Serial Port................................................................................ 32
Figure 16: Checking the USB COM Port Number................................................................. 33
Figure 17: Putty Settings for Login Via Serial Port................................................................ 34
Figure 18: Connecting to LAN Port of COMe Module........................................................... 37
Figure 19: PuTTY Settings for Login via LAN Port ............................................................... 37
Figure 20: MXN-3610 OS Version........................................................................................ 38
Figure 21: PuTTY Settings for Login via Serial Port (CMM)................................................. 39
Figure 22: Connect to CMM via Serial Port.......................................................................... 40
Figure 23: Connecting to LAN Port of CMM......................................................................... 41
Figure 24: PuTTY Settings for Login via LAN Port (CMM) ................................................... 41
Figure 25: Checking the CMM Firmware Version................................................................. 42
Figure 26: Check PacketManager Version........................................................................... 44
Figure 27: Entering the Command Line Interface and Configure Mode................................ 45
Figure 28: Getting Help in PacketManager........................................................................... 46
Figure 29: Getting PacketManager Command Help............................................................. 46
Figure 30: Show OS and SDK Versions............................................................................... 47
Figure 31: Entering Fabric Mode in PacketManager ............................................................ 48
Figure 32: Show All Ports of the MXN-3610 ......................................................................... 49
7
CSA-7400 QSG
1 Overview
1.1 Introduction
The ADLINK CSA-7400 is a high-performance high-density computing platform supporting
four dual Intel® Xeon® E5 compute nodes, interconnected by dual redundant switch
modules. The CSA-7400 can ensure uninterrupted service delivery through hot-swappable
compute nodes and switch modules. It is ideally suited for building next generation high-
performance firewalls and virtualized telecom elements.
The main features of the CSA-7400 are summarized as follows:
Supports four single-system dual Xeon® E5 compute nodes (MCN-2600T)
Dual redundant switch modules provide 40G internal links to each compute node, and
360G uplinks
Supports IPMI 2.0 specification, provides web-based intelligent system management,
and supports SOL on compute nodes
Dual redundant hot-swappable power supply units provide active power management
on compute nodes, support flexible power limit polices
Integrates ADLINK PacketManager software to provide common Layer 2 and Layer 3
switch stacks.
Optionally integrates Wind River® Titanium Server or OPNFV software to provide
carrier grade NFV service
8
CSA-7400 QSG
1.2 Mechanical Overview
1.2.1 Front Panel
1.2.2 Rear Panel
9
CSA-7400 QSG
1.3 Chassis Module List
The CSA-7400 chassis include the following field replaceable units.
4 x CPU Sled (MCN-2600T)
2 x Switch Sled (MXN-3610)
2 x IO Card (NIM-1610)
4 x Fan Module
4 x Power Supply Unit
1.4 Package Contents
Before opening, please check the shipping carton for any damage. If the shipping carton and
contents are damaged, notify the dealer for a replacement. Retain the shipping carton and
packing material for inspection by the dealer. Obtain authorization before returning any
product to ADLINK.
Check that the following items are included in the package. If there are any missing items,
contact your dealer:
CSA-7400 Rackmount Network Appliance
Package check list
Console cable
Power cord
10
CSA-7400 QSG
2 Preparation
2.1 About This Guide
This Quick Start Guide will assist you with getting up and running on your CSA-7400
Platform. The guide addresses the following tasks:
Getting Started
First Power-Up
BIOS Configuration
Network Configuration
Running an Operating System
PacketManager on MXN-3610
Hot-Swapping
For more detailed information, please refer to the other documents available on the ADLINK
website:
CSA-7400:
www.adlinktech.com/PD/web/PD_detail.php?cKind=&pid=1624
PacketManager: www.adlinktech.com/PD/web/PD_detail.php?cKind=&pid=1535
11
CSA-7400 QSG
2.2 Required Equipment for Initial Setup
For purposes of accomplishing the tasks described in this guide, you may need various
cables. The figure 3 shows what you will need to get started. For instructions on how to
install these components, see Chapter 3 Getting Started.
CSA-7400
Power Cord
VGA Cable
Network Cable
(User supplied)
USB-to-USB
Cable
Figure 1: Required Equipment for Initial Setup
12
CSA-7400 QSG
3 Getting Started
For detailed instructions on installing internal components to the MCN-2600T CPU sled and
MXN-3610 switch sled, refer to sections 3.1 and 3.2 of the CSA-7400 User’s Manual.
3.1 Installing a SATA Drive
1. Unlock the ejector handle of the SATA drive tray by pressing the blue unlocking tab
towards the right. The ejector handle will swing outwards.
2. Pull outwards on the ejector handle to remove the SATA drive tray.
13
CSA-7400 QSG
3. Secure the 2.5” SATA drive to the drive tray with 4 screws as shown.
4. Insert the drive tray into the drive bay and press inwards until it is firmly seated.
5. Close the ejector handle and press inwards until it locks in place with a “click”.
14
CSA-7400 QSG
3.2 Connecting VGA cable to the MXN-3610
Locate the VGA connector on the MXN-3610 PCB as shown.
Figure 2: MXN-3610 VGA Connector Location
Connect the VGA cable to the connector on the MXN-3610, Please check position of the red
line (right side), as shown.
Figure 3: Connecting the VGA Cable
VGA cable
VGA connector
15
CSA-7400 QSG
3.3 Assembling the CSA-7400
Insert the MXN-3610 (switch node) and MCN-2600T (CPU node) into the chassis as follows.
Figure 4: CSA-7400 System
3.3.1 Inserting and Removing the MCN-2600T CPU Sled
Insert the CPU sleds into the 4 slots in lower 2 layers.
a. Insert the CPU sled into one of the lower 4 slots and open the ejector handles as shown.
MXN-3610
+ IO card
MCN-2600T
16
CSA-7400 QSG
b. Push the CPU sled into the slot until the front panel is flush with the chassis.
c. When the CPU sled is fully inserted into the chassis, the locking handles will be pulled
into the closed position.
17
CSA-7400 QSG
d. Press inwards on the ejector handles until they lock into place. You will hear a click.
18
CSA-7400 QSG
To remove a CPU sled:
a. Pull outwards to release the locking latch of each ejector handle as shown.
b. Pull outwards on the ejector handles as shown to eject the CPU sled from the chassis.
c. Pull back on the ejector handles to remove the CPU sled from the chassis.
19
CSA-7400 QSG
3.3.2 Inserting and Removing the MXN-3610 Switch Sled
Insert the Switch sleds into the 2 slots in upper 2 layers.
a. Insert the Switch sled into one of the upper 2 slots and open the ejector handles as
shown.
b. Push the Switch sled into the slot by pressing on the front panel of the Switch until the
front panel is flush with the chassis.
Caution: Do NOT press on the front panel of the IO card. Doing so may cause damage
to the Switch and IO card.
X
X
20
CSA-7400 QSG
c. When the Switch sled is fully inserted into the chassis, the locking handles will be pulled
into the closed position.
d. Press inwards on the ejector handles until they lock into place. You will hear a click.
To remove a CPU sled:
Follow the instructions above for removing a CPU sled.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77

ADLINK Technology CSA-7400 Guide de démarrage rapide

Taper
Guide de démarrage rapide

dans d''autres langues