JET JHBS916 Manuel utilisateur

JET
Marque
JET
Modèle
JHBS916
Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
®Registered trademark of JET Equipment & Tools Ltd.
www.jetgroupbrands.com
M13-HT222335
MANUAL
9" x 16" 1-1/2 HP 4 Speed Belt Drive Bandsaw
Prod. No. 222335 Mod. No. JHBS916
2
www.jetgroupbrands.com
Thank you for purchasing this JET bandsaw. Your bandsaw was designed to give you a durable,
reliable and easy to use product. With proper maintenance, your JET machine will give you
years of trouble free operation.
Warranty Policy
JET makes every effort to assure that its products meet high quality standards and warrants to the retail
consumer/purchaser of our products that each product is free from defects in material and workmanship. JET
offers a TWO YEAR LIMITED WARRANTY on this product. Warranty does not apply to defects due directly or
indirectly to misuse, abuse, negligence or accidents, repairs or alterations performed outside our facilities or
to a lack of maintenance.
Warranty Procedure
After receiving authorization from one of our offices, any product for which there is a warranty claim must be
returned prepaid to an authorized warranty depot along with proof of purchase.
Specifications
Contents
Safety Rules ..........................................3
Operating Instructions ..........................4
Blade Selection .....................................4
Single Phase .........................................6
General Operating Instructions .......6-11
Parts List .........................................12-14
Parts Breakdowns ..........................15,16
Replacement Parts ..............................14
Capacity: Round at 90° - 9", at 45° - 6-1/2"
Rectangular at 90° - 4" x 16" – 9" x 12",
at 45° - 9" x 6-1/8"
Throat Depth: 9"
Vise Swivels: 45°
Control Panel: 24V
Floor Space Required: 65" x 28"
Speeds (SFPM): 82, 132, 170, 235
Blade: 1" x 0.032 x 119-1/2"
Blade Wheels: 13"
Bed Height: 25"
Motor (TEFC): 1-1/2HP, 1PH, 230V
Shipping Weight (lb): 704
3
www.jetgroupbrands.com
Safety Rules
a) Wear eye protection.
b) Do not remove jammed cutoff pieces until blade has stopped and power has been disconnected.
c) Maintain proper adjustment of blade tension, blade guides, and thrust bearings.
d) Adjust movable guide to just clear workpiece.
e) Clamp workpiece firmly in vise.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Always check to see that keys and adjusting wrenches are
removed from tool before turning it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to
rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
9. This tool should be connected to a ground metal permanent wiring system; or to a system having an
equipment-grounding conductor.
10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may
get caught in moving parts. Safety footwear is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses
only have impact resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work at all times. It’s safer than using your hand and it frees both
hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, etc.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories.
The use of improper accessories may cause risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function–check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.
WARNING
For Your Own Safety
Read Operator’s Manual Before Operating Saw
4
www.jetgroupbrands.com
Operating Instructions
1. Check Coolant: Low coolant level causes
foaming and high blade temperatures. Dirty or
weak coolant can clog pump, causes crooked
cuts, low cutting rate and permanent blade
failure. Dirty coolant causes the growth of
bacteria with ensuing skin irritation. Coolant is
water soluble.
2. Keep vise slides clean and oiled.
3. Clean chips from blade wheels and the areas
around wheels. Keep chip brush in good repair.
4. Saw Guide: Keep saw guides properly adjusted.
Loose guides will affect cutting accuracy.
5. Check saw blade for sharpness.
6. Blade Speed: Is blade speed set correctly for
workpiece material and shape?
7. Check Blade Tension: Particularly after initial
cuts with a new blade.
Blade Selection
A. Never use a blade so coarse that less than 3
teeth are engaged in the workpiece at any time.
(Too few teeth will cause teeth to strip out.)
B. Never use a blade finer than required to obtain a
satisfactory surface finish or satisfactory flatness.
(Too many teeth engaged in the work piece will
reduce sawing rate; cause premature blade wear;
produce “dished” cuts or cuts which are neither
square nor parallel.)
C. The chart which follows is intended as a general
guide to good sawing practices. Consult
your blade supplier or qualified technician for
complete information for operational details of
saw blades and their use.
The Selection of Saw Blades
Remarks: HSS-High Speed Steel Sawblade
HCS-High Carbon Steel Sawblade
NOTE:
1. When standard wall pipe, tubes, channel iron
and angle I beams are cut, a 10 pitch saw blade
of wave-set type or sawblade of (HSS) 6/10T is
frequently used to good advantage.
2. Tubes or materials with wall thickness or web
thickness of 1/2" or more can usually use an 8 or
6 pitch sawblade of (HSS) 4/6T satisfactorily.
3. When rectangular solid bar stock is to be sawed,
the work should be loaded so that the cut is
made across the thinnest cross section. The
pitch (or number of teeth per inch of blade)
selected must provide engagement of at least 3
teeth in the workpiece. Should application of this
rule not be possible because the thinnest cross
section is too thin, the piece must be loaded so
that the cut is made across the wider dimension
and a coarser blade selected from the listing of
recommendations for round and square
solid bars.
Cutting
Material
<3mm >5mm >50mm >100mm >150mm >200mm
Sawblade <0.12" >0.2" >2" >4" >6" >8"
(HSS) 14T
(HSS) 6/10T
(HSS) 5/8T
(HSS) 4/6T
(HSS) 3/4T
(HSS) 2/3T
(HSS) 1/2T
(HCS) 10T
(HCS) 8T
(HCS) 6T
(HCS) 4T
(HCS) 2T
5
www.jetgroupbrands.com
6
www.jetgroupbrands.com
Single Phase
Refer to the wiring drawing inside the electrical box
and on page 5 for proper motor and transformer
connections, lead selection and wiring connections
from the motor to the power source for the voltage
you are using. Important: Immediately after wiring
the machine, remove the drive belt, turn on the
power and make sure the motor is running in the
right direction (counter-clockwise when looking at
the motor shaft.)
General Operating
Instructions
Removing and Installing the Blade
When your machine was shipped, a blade was
supplied and mounted on the saw. When selecting
a new blade refer to the selection of sawblades.
The machine requires a blade 1" x 0.032" x 119-1/2"
(27mm x 0.9mm x 3,035mm).
1. Disconnect the machine from the
power source.
2. Raise the saw frame about 6" and close the feed
control valve by turning it clockwise as far as it
will go. (Do not over tighten.)
3. Open both wheel covers and clean the chips out
of the machine.
4. a) Loosen the nut at the back of the left hand
wheel, (item A-1).
b) To release blade tension, turn the blade
tension hand wheel (item C, Fig. 1),
counter-clockwise.
5. Slide left blade guide arm to the right as far
as possible.
6. Remove the blade from both wheels and out of
each blade guide.
7. Make sure the teeth of the new blade are
pointing in the direction of travel. If necessary,
turn the blade inside out.
8. Mount the blade in place on the wheels
(A-1 and A-2) and through the upper
blade guard. (B) Fig.1.
9. Work the blade all the way up between the blade
guide bearings with the back of the blade against
the back-up bearing, as shown in Fig.2.
Fig. 1
Fig. 2
C
A1
B
A2
7
www.jetgroupbrands.com
Note: If bearings need adjustment, refer to
the section “Adjusting Blade Guide
Roller Bearings.”
10.Put light tension on the blade and work it on both
wheels, as shown in Fig.3. Make sure that the
back of the blade is against the wheel flanges of
both wheels. This is very important.
11.Proper tension is achieved by turning the blade
tension wheel (item C Fig 1) clockwise.
When the red line of the blade tension scale is
at or near the 2,000 mark on the left of the scale,
proper tension has been achieved.
Now tighten the nut at the back of the left hand
wheel (A-1). Check blade tension during the
performance of item 12. If proper tension has not
been attained, loosen the nut at the back of the
wheel (A-1) again and turn blade tension wheel
CCW so the scale line is nearer to the 2,000 mark
to the left of the scale. Retighten the nut.
Go to step 12 to confirm position, tracking and
proper tension of the blade.
12.Jog the power “on” and “off” to be sure the
blade is in place and tracking properly. If blade is
not tracking properly refer to the section tracking
the blade.
Starting and Stopping the Machine
The saw frame must be in the raised position before
starting the machine. The machine is started by
pushing the start button (A) Fig.4, and will continue
to run until the saw frame is in the down position at
the end of the cut, or when the stop button (B) is
pushed. Pushing the stop button (B) will stop the
motor at any time.
Blade Tracking Adjustment
Blade tracking has been set at the factory and
should require no adjustment. If a tracking problem
occurs, adjust the machine as follows:
Since tracking can only be adjusted while machine
is running, it is suggested that this adjustment
be accomplished by qualified personnel that are
familiar with this type of adjustment and the dangers
associated with it.
1. Disconnect the machine from the
power source.
2. Raise saw arm to its highest position and close
cutting pressure control valve to hold saw arm
in place.
3. Locate tracking adjustment plate on the back
side of the drive blade wheel.
Fig. 3
Fig. 4
A
B
8
www.jetgroupbrands.com
4. Loosen the three bolts (A - Fig.5) located on the
top of the tracking nuts.
5. Tracking adjustment is accomplished by either
loosening or tightening three adjusting nuts
(B - Fig.5).
6. Tracking is set properly when the back of the
blade lightly touches the wheel flange.
Note: over-tracking (allowing blade back to rub
hard against wheel flange) will damage
the blade wheels and blade.
7. Tighten locking bolts (A) once proper tracking
is achieved.
8. Connect machine to the power source.
Adjusting Feed Rate
When the hydraulic regulating micro switch (A) Fig.6
is turned clockwise as far as it will go, the saw frame
will not move down. By turning the feed control
valve counter-clockwise, you regulate the flow of oil
from the cylinder and determine the speed at which
the saw frame will lower and the blade will feed
through the work. Too many factors are involved to
make tabulated data practical on feed rates. As a
general rule, an even pressure without forcing the
blade gives best results. Avoid forcing the blade at
the start as this may shorten blade life and produce
a bad cut. Inspecting the chips while the cut is being
made will indicate whether the feed rate is correct.
Fine powdery chips indicate a feed rate which is too
light. The teeth are rubbing over the surface instead
of cutting. Burned chips indicate excessive feed
which causes the teeth to break off as the blade
overheats. The ideal feed rate is indicated by chips
that have a free curl, this will give the fastest cutting
time and longest blade life.
Adjusting Blade Guide Brackets
The blade guides should be set as close to the vise
jaws as possible. The right blade guide bracket, is
not adjustable and is set at the factory to clear the
right hand vise jaw. The left blade guide bracket
can be moved to the left or right depending on the
position of the left hand vise jaw. To move the left
blade guide bracket (A) Fig.7, loosen the hand knob
(B), position blade guide bracket and tighten
hand knob (B).
Fig. 5
Fig. 6
A
B
A
9
www.jetgroupbrands.com
Automatic Shut-Off Adjustment
The motor should shut off immediately after the
blade has cut through the material and just before
the head comes to rest on the horizontal stop bolt.
If the machine continues to run after the workpiece
has been fully cut, locate and adjust the micro switch
mounting plate (part #45) downward. If the machine
shuts off before the workpiece has been completely
cut, move the micro switch mounting plate upward.
Thrust Roller Adjustment
1. Disconnect the machine from the
power source.
2. Loosen two hex socket cap screws (A-Fig.8).
3. Move guide seat (B - Fig.8) up or down until a
clearance of 0.003" to 0.005" between back of
blade and thrust roller is obtained.
4. Tighten two hex socket cap screws
(A - Fig.8).
5. Repeat for other blade guide assembly.
6. Connect machine to power source.
Guide Roller Adjustment
1. Disconnect the machine from the
power source.
2. Loosen blade guides (A – Fig.9) by loosening
screws (B). Slide blade guides away from blade.
3. Loosen locking screws (C) by using a
hex wrench.
4. Adjust the eccentric bushings with a combination
wrench until the ball bearings are snug to the
blade. Note: blade should travel freely up and
down between the ball bearings. Do not pinch
the blade.
5. Tighten locking screws (C).
6. Slide blade guides back into contact with blade
and tighten screws (B).
7. Connect machine to the power source.
Fig. 9
Fig. 7
Fig. 8
A
B
B
A
Locking
Screw
Guide
Seat
C
A
B
Blade
Thrust
Roller
Eccentric
Bushing
Inner Roller
(Blade Guide Roller)
10
www.jetgroupbrands.com
Vise Adjustment
To position the moveable vise jaw:
1. Turn vise handwheel (A – Fig.10) 1/2 turn
counter-clockwise.
2. Move rack block (B – Fig.10) to desired location
by sliding along the bed. Place the rack block
onto the rack.
3. Turn the handwheel to tighten the vise.
To adjust the vise for angle cutting:
1. Loosen bolts and move vise jaw (C – Fig.10) to
desired location.
2. Set the vise to desired angle, reinstall nuts and
tighten the nut and bolt assemblies.
3. Adjust the movable vise parallel to the fixed vise
by loosening bolt (D – Fig.10) adjusting
to parallel and tightening bolt.
Setting Up the Machine for Operation
1. Select the proper speed and blade for the type of
material you are going to cut.
2. Make sure blade tension is adjusted properly.
3. Lift the saw frame up and turn off the hydraulic
regulating micro switch.
4. Place the stock between the vise jaws, set the
stock for the desired width of cut and tighten
the vise.
5. Make sure the left blade guide bracket (A) is
adjusted as close as possible to the left vise
jaw (B) Fig.11.
6. Turn the hydraulic regulating micro switch (C)
Fig.11, counter-clockwise until the saw blade
begins to lower at the desired rate.
7. Proceed to cut through the workpiece, as
shown in Fig.11. The machine will shut off upon
completion of cut.
Fig. 11
A
C
Fig. 10
A
B
C
D
11
www.jetgroupbrands.com
Changing Speeds
Your machine is provided with four speeds.
To change speeds, proceed as follows:
1. Disconnect the machine from the
power source.
2. Loosen and remove knob, (A) Fig.12, and swing
belt and pulley guard (B) to the side
of the machine.
3. Release tension on the belt by turning the tension
lock nut (part #107) counter-clockwise and letting
the motor swing forward.
4. Shift the belt Fig.12, to the desired grooves on
the pulleys and adjust belt tension by pulling
the motor plate back until correct belt tension is
obtained and tighten tension lock nut.
5. Close belt and pulley guard, replace and tighten
knob (A).
Gear Case
After the first 50 hours of use the gear box should
be drained and refilled. Remove drain plug located
under the gear box motor shaft and drain all of the
oil out of the gear box and replace plug. Remove oil
filler plug (A) Fig. 13 located underneath the right
blade wheel and fill the gear box with 1-1/2 pints of
ESSO CYLESSO TK460 or equivalent. Oil should
then be changed after every 500 hours of operation.
A
Fig. 13
Fig. 12
A
B
12
www.jetgroupbrands.com
Ref. Part No. Description
Qty.
Qté.
1 PDNJHBS9161 Base / Socle 1
1-1 PDNJHBS9161-1 Wire Protector / Protège-fils 1
1-2 PDNJHBS9161-2 Power Cord / Cordon d’alimentation 1
1-3 PDNJHBS9161-3
Hex. Cap Bolt
Vis d’assemblage à tête hexagonale
4
1-4 PDNJHBS9161-4 Nut / Écrou M12 4
1-5 PDNJHBS9161-5 Washer / Rondelle M6 2
1-6 PDNJHBS9161-6 Lock Washer / Rondelle frein 2
1-7 PDNJHBS9161-7
Hex. Socket Cap
Vis d’assemblage à six pans creux
2
1-8 PDNJHBS9161-8 Conjunction Box / Boîte de jonction 1
1-9 PDNJHBS9161-9
Rubber Plate
Plaque en caoutchouc
1
1-10 PDNJHBS9161-10 Cover / Couvercle 1
1-11 PDNJHBS9161-11 Round Head Screw / Vis a tête ronde 4
2 PDNJHBS9162 Hose / Flexible 1
2-1 PDNJHBS9162-1 Drain Plug / Bouchon de vidage 3/8 pt 1
3 PDNJHBS9163 Hose Clamp / Collier de serrage 2
4 PDNJHBS9164
Coolant Pump
Pompe de refroidissement
1
5 PDNJHBS9165 Round Head Screw / Vis à tête ronde 2
6 PDNJHBS9166 Lock Washer / Rondelle frein 2
7 PDNJHBS9167 Hose/Flexible 1
9 PDNJHBS9169
Coolant Gauge / Indicateur de niveau
de liquide de refroidissement
1
10 PDNJHBS91610 ChipTray / Bac à copeaux 1
11 PDNJHBS91611 Bed / Banc 1
11-1 PDNJHBS91611-1 Nut / Écrou M10 1
11-2 PDNJHBS91611-2
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M10 x 30
1
12 PDNJHBS91612
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M8 x 30
8
13 PDNJHBS91613 Washer / Rondelle M8 8
14 PDNJHBS91614 Lock Washer / Rondelle frein 8
15 PDNJHBS91615 Nut / Écrou M8 8
16 PDNJHBS91616 Work Stop Bracket / Support de butée 1
17 PDNJHBS91617 Work Stop Rod / Tige de butée 1
18 PDNJHBS91618 Lock Knob / Bouton de blocage 1
19 PDNJHBS91619 Work Stop / Butée 1
21 PDNJHBS91621
Hand Wheel Assembly
Volant de manoeuvre
1
21-1 PDNJHBS91621-1 Set Screw / Vis de pression 1
22 PDNJHBS91622 Lead Screw Seat / Siège de vis-mère 1
23 PDNJHBS91623
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M8 x 30
2
23-1 PDNJHBS91623-1 Lock Washer / Rondelle frein 2
23-2 PDNJHBS91623-2 Washer / Rondelle M8 2
24-1 PDNJHBS91624-1 Lead Screw / Vis-mère 1
24-2 PDNJHBS91624-2 Key / Clavette 5 x 20 1
25-1 PDNJHBS91625-1
Lead Screw Bracket
Support de vis-mère
1
25-2 PDNJHBS91625-2
Hex. Socket Cap
Vis d’assemblage à six pans creux
2
26-1 PDNJHBS91626-1 Slide Bracket / Support de glissière 1
26-2 PDNJHBS91626-2 Set Screw / Vis de pression M6 x 8 1
27-1 PDNJHBS91627-1 Rack / Crémaillère 1
28-1 PDNJHBS91628-1 Rack Block / Coulisseau
29-1 PDNJHBS91629-1 Pin / Goupille 1
30 PDNJHBS91630 Closed Bearing / Palier fermé HK25 15 2
30-1 PDNJHBS91630-1 Bushing / Douille 1
31 PDNJHBS91631 Torsion Spring / Ressort de torsion 1
Ref. Part No. Description
Qty.
Qté.
32 PDNJHBS91632 Pivot Shaft / Axe de pivotement 1
32-1 PDNJHBS91632-1 Washer / Rondelle 2
2-2 PDNJHBS91632-2
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M12 x 20
2
32-3 PDNJHBS91632-3 Grease Cup / Graisseur Stauffer 2
33 PDNJHBS91633
Pivot Bracket
Support d’axe de pivotement
1
33-1 PDNJHBS91633-1 Set Screw / Vis de pression M10 x 12 1
34 PDNJHBS91634 Nut / Écrou M12 1
35 PDNJHBS91635 Washer / Rondelle M12 1
36 PDNJHBS91636
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M12 x 20
1
37 PDNJHBS91637
Torsion Spring Shaft
Axe de ressort de torsion
1
38 PDNJHBS91638 C-Ring / Anneau en C 1
39 PDNJHBS91639
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M8 x 30
1
39-1 PDNJHBS91639-1 Washer / Rondelle M8 1
40 PDNJHBS91640
Motor Tilt Plate
Plateau d’inclinaison du moteur
1
40-1 PDNJHBS91640-1 Nut / Écrou M8 1
41 PDNJHBS91641
Limit Switch Plate / Plaque
d’interrupteur de fin de course
1
42 PDNJHBS91642 Washer / Rondelle M8 2
42-1 PDNJHBS91642-1 Lock Washer / Rondelle frein 2
43 PDNJHBS91643
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M12 x 20
2
44 PDNJHBS91644
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M12 x 20
4
45 PDNJHBS91645
Limit Switch
Interrupteur de fin de course
1
47 PDNJHBS91647 Cylinder Pin / Goupille cylindrique 1
48 PDNJHBS91648 C-Ring / Anneau en S-20 1
49 PDNJHBS91649 C-Ring / Anneau en S-25 2
50 PDNJHBS91650
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M12 x 20
1
51 PDNJHBS91651
Hydraulic Cylinder Assembly
Vérin hydraulique
1
52 PDNJHBS91652
Cylinder Pin-Top
Goupille cylindrique-partie supérieure
1
52-1 PDNJHBS91652-1 Pin / Goupille 1
53 PDNJHBS91653
Hydraulic Mounting
Montage hydraulique
1
53-1 PDNJHBS91653-1 Lock Washer / Rondelle frein 2
53-2 PDNJHBS91653-2 Hex. Bolt / Boulon hexagonal 2
54 PDNJHBS91654 Hex. Bolt / Boulon hexagonal 2
55 PDNJHBS91655 Washer / Rondelle M12 2
56 PDNJHBS91656 Lock Plate / Plaquette frein 1
57 PDNJHBS91657 Nut / Écrou 2
58 PDNJHBS91658 Spring Bracket / Support de ressort 1
58-1 PDNJHBS91658-1
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M12 x 20
2
58-2 PDNJHBS91658-2 Washer / Rondelle M8 2
58-3 PDNJHBS91658-3 Washer / Rondelle M8 2
58-4 PDNJHBS91658-4 Nut / Écrou M8 2
59 PDNJHBS91659
Spring Adjustable Rod
Tige de réglage à ressort
1
60 PDNJHBS91660 Spring / Ressort 1
61 PDNJHBS91661 Angle Scale / Cadran angulaire 1
61-1 PDNJHBS91661-1 Rivet 3
62 PDNJHBS91662
Hex. Cap Bolt / Vis d’assemblage à tête
hexagonale M12 x 20
1
Parts Breakdown / Prèsentes diréctives
13
www.jetgroupbrands.com
Ref. Part No. Description
Qty.
Qté.
63 PDNJHBS91663 Washer / Rondelle M12 1
63-1 PDNJHBS91663-1 LockWasher / Rondelle frein M12 2
64 PDNJHBS91664
Vise Jaw - Left
Mordache d'étau, côté gauche
1
65 PDNJHBS91665 Hex. Cap Bolt / Boulon hexagonale 1
66 PDNJHBS91666 Washer / Rondelle M12 1
66-1 PDNJHBS91666-1 Lock Washer / Rondelle frein 2
67 PDNJHBS91667
Vise Jaw - Right
Mordache d'étau, côté droit
1
68 PDNJHBS91668 Hex. Cap Bolt / Boulon hexagonale 1
69 PDNJHBS91669
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
1
69-1 PDNJHBS91669-1 Lock Washer / Rondelle frein 1
69-2 PDNJHBS91669-2 Washer / Rondelle M6 1
70 PDNJHBS91670
Electrical Panel Cover
Couvercle de tableau de distribution
1
70-1 PDNJHBS91670-1 Pin / Goupille 2
71 PDNJHBS91671 Fuse Block / Bloc-fusibles 2
72 PDNJHBS91672 Contactor (main) / Contacteur (principal) 1
72-1 PDNJHBS91672-1 Contactor (pump) / Contacteur (pompe) 1
73 PDNJHBS91673 Transformer / Transformateur 1
74 PDNJHBS91674 Terminal Strip / Bornier 1
75 PDNJHBS91675 Handle / Poignée 2
76 PDNJHBS91676 Round Head Screw / Vis à tête ronde 4
76-1 PDNJHBS91676-1 Washer / Rondelle M6 4
77 PDNJHBS91677
Hex. Cap Bolt Cap
Vis d’assemblage à tête hexagonale
10
77-1 PDNJHBS91677-1 Lock Washer / Rondelle frein 2
77-2 PDNJHBS91677-2 Washer / Rondelle M6 2
78 PDNJHBS91678
Wire Brush Guard
Protecteur de brosse métallique
1
79 PDNJHBS91679
Blade Wheel Cover
Couvercle de roue à ailettes
1
80 PDNJHBS91680
Blade Wheel Cover
Couvercle de roue à ailettes
1
81 PDNJHBS91681
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
6
82 PDNJHBS91682 Bushing / Douille 1
83 PDNJHBS91683 Washer / Rondelle 1
84 PDNJHBS91684 Drive Wheel / Roue d’entraînement 1
86 PDNJHBS91686 Hex. Cap Bolt / Boulon hexagonal 2
87 PDNJHBS91687 Round Head Screw / Vis à tête ronde 2
88 PDNJHBS91688 Filter Screen / Tamis de filtre 1
89 PDNJHBS91689 Hex. Cap Bolt / Boulon hexagonal 4
89-1 PDNJHBS91689-1 Lock Washer / Rondelle frein 4
90 PDNJHBS91690 Lock Knob / Bouton de blocage 4
92 PDNJHBS91692
Blade Wheel Box - right
Carter de roue à ailettes, côté droit
1
92-1 PDNJHBS91692-1 Set Screw / Vis de pression M10 x12 2
93 PDNJHBS91693 Connector / Connecteur 1
94 PDNJHBS91694
Gear Box Assembly
Carter d’engrenages
1
94-1 PDNJHBS91694-1 Key / Clavette 7mm 1
95 PDNJHBS91695 Key / Clavette 7mm 1
96 PDNJHBS91696 Pulley Cover / Couvre-poulie 1
96-1 PDNJHBS91696-1 Lock Knob / Bouton de blocage 1
97 PDNJHBS91697
Gear Box Pulley
Poulie de carter d’engrenages
1
98 PDNJHBS91698 Belt / Courroie A.39 1
99 PDNJHBS91699 Motor Pulley / Poulie du moteur 1
99-1 PDNJHBS91699-1 Set Screw / Vis de pression M8 x 10 1
Ref. Part No. Description
Qty.
Qté.
100 PDNJHBS916100 Hex. Cap Bolt / Boulon hexagonal 2
100-1 PDNJHBS916100-1 Washer / Rondelle M8 2
100-2 PDNJHBS916100-2 Lock Washer / Rondelle frein M8 2
102 PDNJHBS916102 Support Shaft / Arbre-support 1
102-1 PDNJHBS916102-1 C-Ring / Anneau en C S-19 1
104 PDNJHBS916104
Motor Mount Bracket
Fixation du support de moteur
1
104-1 PDNJHBS916104-1 Washer / Rondelle M12 1
104-2 PDNJHBS916104-2 Nut / Écrou 1
105 PDNJHBS916105 Column / Colonne 1
106 PDNJHBS916106
Hex.Socket Cap Screw
Vis d’assemblage à six pans creux
6
106-1 PDNJHBS916106-1 Lock Washer / Rondelle frein 6
106-2 PDNJHBS916106-2 Nut / Écrou M12 6
107 PDNJHBS916107 Hex. Cap Bolt / Boulon hexagonal 1
108 PDNJHBS916108 Washer / Rondelle M8 1
108-1 PDNJHBS916108-1 Lock Washer / Rondelle frein 1
109 PDNJHBS916109 Hex. Cap Bolt / Boulon hexagonal 4
109-1 PDNJHBS916109-1 Washer / Rondelle M8 4
110 PDNJHBS916110
Motor Mount Plate
Plateau de support du moteur
1
111 PDNJHBS916111 Motor / Moteur 1
112 PDNJHBS916112 Washer / Rondelle M8 4
112-1 PDNJHBS916112-1 Lock Washer / Rondelle frein 4
113 PDNJHBS916113 Nut / Écrou M8 4
114 PDNJHBS916114 Key/Clavette 7mm 1
116 PDNJHBS916116
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
2
118 PDNJHBS916118 Ball Bearing / Roulement à billes 608ZZ 2
118-1 PDNJHBS916118-1 Lock Washer / Rondelle frein 2
119 PDNJHBS916119 Hex. Cap Bolt / Boulon hexagonal 2
120 PDNJHBS916120 Washer / Rondelle M12 2
121 PDNJHBS916121 Ball Bearing / Roulement à billes 608ZZ 3
122 PDNJHBS916122 Idler Wheel / Roue folle 1
123 PDNJHBS916123 Blade Guard / Protège-lame 1
123-1 PDNJHBS916123-1 Hex. Cap Bolt / Boulon hexagonal 1
123-2 PDNJHBS916123-2 Washer / Rondelle M8 2
124 PDNJHBS916124
Guide Bracket - Left
Support de guide, côté gauche
1
124-1 PDNJHBS916124-1 Set Screw / Vis de pression M8 x 16 3
124-2 PDNJHBS916124-2 Nozzle / Buse 1
124-3 PDNJHBS916124-3 Nozzle Support / Support de buse 1
124-4 PDNJHBS916124-4 Lock Washer / Rondelle frein 1
124-5 PDNJHBS916124-5
Hex. Cap Bolt
Boulon hexagonal M6 x 12
1
125 PDNJHBS916125 Washer / Rondelle M8 x 25 4
126 PDNJHBS916126 Ball Bearing / Roulement à billes 608ZZ 8
127 PDNJHBS916127 Centric Sleeve / Douille de centrage 2
127-1 PDNJHBS916127-1
Eccentric Sleeve
Douille de excentrique
2
128 PDNJHBS916128 Lock Washer / Rondelle frein M8 4
129 PDNJHBS916129
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
4
130 PDNJHBS916130
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
4
130-1 PDNJHBS916130-1 Lock Washer / Rondelle frein 4
130-2 PDNJHBS916130-2 Washer / Rondelle 8
131 PDNJHBS916131
Tungsten Carbide Blade Guide
Guide-lame en carbure de tungstène
4
132 PDNJHBS916132 Hex. Cap Bolt / Boulon hexagonal 2
133 PDNJHBS916133 Lock Washer / Rondelle frein M8 2
Parts Breakdown / Prèsentes diréctives
14
www.jetgroupbrands.com
Ref. Part No. Description
Qty.
Qté.
133-1 PDNJHBS916133-1 Washer / Rondelle M8 2
134 PDNJHBS916134 Adjustable Bracket / Support réglable 1
135 PDNJHBS916135 Scale / Échelle 1
135-1 PDNJHBS916135-1 Round Head Screw / Vis à tête ronde 4
136 PDNJHBS916136
Hex. Socket Cap Screw
Vis d’assemblage à tête hexagonale
2
137 PDNJHBS916137 Slide / Coulisseau 1
138 PDNJHBS916138
Blade Bracket - Left
Support de lame gauche
1
140 PDNJHBS916140 Hex. Cap Bolt / Boulon hexagonal 2
140-1 PDNJHBS916140-1 Lock Washer / Rondelle frein 2
141 PDNJHBS916141
Lock Handle
Poignée de blocage 3/8 x 30
1
142 PDNJHBS916142 Stationary Plate / Plateau fixe 1
143 PDNJHBS916143 Set Screw / Vis de pression M8 x 10 4
144 PDNJHBS916144
Blade Bracket - Right
Support de lame droit
1
145 PDNJHBS916145 Hex. Cap Bolt / Boulon hexagonal 1
145-1 PDNJHBS916145-1 Lock Washer / Rondelle frein 1
146 PDNJHBS916146 Washer / Rondelle M6 1
147 PDNJHBS916147 Wire Brush / Brosse métallique 1
148 PDNJHBS916148
Wire Brush Rod
Tige de brosse métallique
149 PDNJHBS916149
Guide Bracket - Right
Suport de guide droit
1
149-1 PDNJHBS916149-1 Nozzle / Buse 1
149-2 PDNJHBS916149-2
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
1
150 PDNJHBS916150 Spring / Ressort 1
151 PDNJHBS916151 Set Screw / Vis de pression 1
152 PDNJHBS916152 Nut / Écrou M10 1
153 PDNJHBS916153
Hex. Socket Cap
Vis d’assemblage à six pans creux
1
155 PDNJHBS916155 Nut / Écrou M12 1
155-1 PDNJHBS916155-1 Hex. Cap Bolt / Boulon hexagonal 4
155-2 PDNJHBS916155-2 Lock Washer / Rondelle frein M12 4
155-3 PDNJHBS916155-3 Washer / Rondelle M12 4
156 PDNJHBS916156 Stand Bolt / Boulon prisonnier M12 x 50 1
157 PDNJHBS916157 Blade Guard / Protège-lame 1
157-1 PDNJHBS916157-1
Blade Guard - Down
Protège-lame inférieur
1
158 PDNJHBS916158 Lock Knob / Bouton de blocage 2
159 PDNJHBS916159 Hose / Flexible 8 x 700mm 1
160 PDNJHBS916160 Adjusting Valve / Robinet de réglage 2
160-1 PDNJHBS916160-1 Hose / Flexible 8 x 320mm 1
160-2 PDNJHBS916160-2 Hose Clamp / Collier de serrage 2
160-3 PDNJHBS916160-3 Brace / Pièce de renforcement 2
160-4 PDNJHBS916160-4 Lock Washer / Rondelle frein 4
160-5 PDNJHBS916160-5 Hex. Cap Bolt / Boulon hexagonal 4
161 PDNJHBS916161
Power Indicator Light
Témoin d’alimentation
1
161-1 PDNJHBS916161-1 Switch With Key / Ensemble interrupteur 1
162 PDNJHBS916162 Switch / Interrupteur 1
163 PDNJHBS916163
Emergency Stop Switch
Interrupteur d’arrête de secours
1
164 PDNJHBS916164 Pump Switch / Interrupteur de pompe 1
165 PDNJHBS916165
Speed Control Valve
Régulateur de vitesse
1
166-1 PDNJHBS916166-1 Hose / Flexible 5/160 x 400mm 1
166-2 PDNJHBS916166-2 Hose / Flexible 5/160 x 940mm 1
168 PDNJHBS916168 Control Box / Coffret de commande 1
Ref. Part No. Description
Qty.
Qté.
169 PDNJHBS916169 Control Panel / Panneau de commande 1
169-1 PDNJHBS916169-1
Oil Regulating Switch
Commande régulatrice de débit d’huile
1
169-2 PDNJHBS916169-2 On-Off Switch / Interrupteur marche-arrêt 1
170 PDNJHBS916170 Round Head Screw / Vis à tête ronde 6
171 PDNJHBS916171 Wheel Box - Left / Carter de roue gauche 1
171-1 PDNJHBS916171-1 Lock Plate / Plateau de blocage 1
171-2 PDNJHBS916171-2 Washer / Rondelle M6 2
171-3 PDNJHBS916171-3 Hex. Cap Bolt / Boulon hexagonal 2
172 PDNJHBS916172 Handle / Poignée M12 1
173 PDNJHBS916173 Nut / Écrou M12 2
175 PDNJHBS916175 Round Head Screw / Vis à tête ronde 2
176 PDNJHBS916176 Indicator Scale / Cadran indicateur 1
177 PDNJHBS916177 Slide Bracket / Support de coulisseau 1
178 PDNJHBS916178 Tension Shaft / Arbre de tension 1
179 PDNJHBS916179 Key / Clavette 5 x 15 1
180 PDNJHBS916180 Handwheel / Volant de manoeuvre 1
181 PDNJHBS916181 Disc Spring / Rondelle Belleville 13
182 PDNJHBS916182 Flat Washer / Rondelle plate 1
183 PDNJHBS916183 Tension Indicator / Indicateur de tension 1
184 PDNJHBS916184 Thrust Bearing / Butée 51104 1
187 PDNJHBS916187 Slide / Coulisseau 1
188 PDNJHBS916188 Set Screw / Vis de pression 5/16 x 38 1
189 PDNJHBS916189 Extension Bar / Barre de rallonge 1
190 PDNJHBS916190
Blade Wheel Shaft
Axe de roue à ailettes
1
191 PDNJHBS916191 Nut / Écrou M16 1
191-1 PDNJHBS916191-1 Set Screw / Vis de pression 5/16 x 38113 1
192 PDNJHBS916192
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
4
193 PDNJHBS916193
Hex. Socket Cap Screw
Vis d’assemblage à six pans creux
1
193-1 PDNJHBS916193-1 Washer / Rondelle 1
194 PDNJHBS916194 Gib / Lardon de guidage 2
195 PDNJHBS916195 Hex. Cap Bolt / Boulon hexagonal 3
196 PDNJHBS916196 Hex. Cap Bolt / Boulon hexagonal 3
197 PDNJHBS916197 Lock Washer / Rondelle frein 3
Ordering Replacement Parts
Replacement parts may be ordered from your local distributor or directly
from JET. When ordering replacement parts always provide the
following information:
1. The model number and serial number of the machine.
2. The part number.
3. The part name.
4. The desired quantity of the part.
Commande des pièces de rechange
Vous pouvez commander des pièces de rechange auprès du distributeur
de votre localité ou en vous adressant directement à JET. Lorsque vous
commandez des pièces de rechange, n’oubliez jamais de fournir les
renseignements suivants :
1. Le modèle et le numéro de série de la machine.
2. Le code de la pièce de rechange.
3. La description de la pièce de rechange.
4. La quantité commandée.
Parts Breakdown / Prèsentes diréctives
15
www.jetgroupbrands.com
16
www.jetgroupbrands.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

JET JHBS916 Manuel utilisateur

JET
Marque
JET
Modèle
JHBS916
Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents