Page 1
Vented Slope Glaze Burner
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
VENTED
DECORATIVE LOG SET
FOR INSTALLATION IN
SOLID-FUEL BURNING FIREPLACES
MODELS
VSM-18-2 VSR-18-2
VSM-24-2 VSR-24-2
VSM-30-2 VSR-30-2
WARNING
If the information in these instructions are
not followed exactly, a re or explosion
may result causing property damage, per-
sonal injury or loss of life.
— Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of
this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the re department.
— Installation and service must be per-
formed by a qualied installer, service
agency or the gas supplier.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
WARNING
If not installed, operated and maintained in accordance
with the manufacturer's instructions, this product
could expose you to substances in fuel or from fuel
combustion which can cause death or serious illness.
AVERTISSEMENT
Assurez vous de bien suivre les instructions données
dans cette notice pour réduire au minimum le risque
d’incendie ou d’explosion ou pour éviter tout dom-
mage matériel, toute blessure ou la mort.
— Ne pas entreposer ni utiliser d’essence ni d’autres
vapeurs ou liquides inammables dans le voisnage
de cet appareil ou de tout autre appareil.
— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d’allumer d’appareil.
• Ne touchez a aucun interrupteur. Ne pas vous
servir des téléphones se trouvant dans le bâti-
ment où vous vous trouvez.
• Laissez le bâtiment immédiatement
• Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de
gaz, appelez le service des incendies.
— L’installation et l’entretien doivent être assurés par
un installateur ou un service d’entretien qualié ou
par le fournisseur de gaz.
WARNING
This log set is to be installed only in a solid-fuel burn-
ing replace with a working ue constructed of non-
combustible material. The vent damper must also have
a damper clamp attached to it to keep the damper from
accidentally closing during operation.
32631-3-0717Page 2
CAUTION: If logs or branches are damaged do not use.
A certain amount of sooting will occur which enhances the realistic look of the logs and branches. If an excessive
amount of sooting does occur you can use a gas log cleaner to remove the soot build-up or lightly brush off the
soot build-up with a soft bristle brush taking care not to damage the logs and branches.
TABLE OF CONTENTS
Section Page
Important Safety Information ...................................................................................................... 3
Safety Information for Users of LP Gas ....................................................................................... 4
Introduction .................................................................................................................................. 5
General Information ..................................................................................................................5-6
Fireplace Preparation ...............................................................................................................6-7
Before Fully Installing the Appliance ............................................................................................ 7
Gas Supply .................................................................................................................................. 8
Placement of Glowing Embers and Lava Rock ........................................................................... 9
Operation Instructions/Flame Appearance .................................................................................. 9
VSM-(18, 24, 30) Lighting Instructions ..................................................................................... 10
VSR-(18, 24, 30) Lighting Instructions ...................................................................................... 11
Pilot and Main Burner Flame Characteristics ............................................................................ 12
Wiring ........................................................................................................................................ 13
Cleaning and Servicing .............................................................................................................. 13
Troubleshooting ......................................................................................................................... 14
Parts List .................................................................................................................................... 15
Parts View ..................................................................................................................................16
Propane (LP) Gas Conversion Instructions ............................................................................... 17
Natural Gas Conversion Instructions ......................................................................................... 18
Master Parts Distributor List ...................................................................................................... 19
How To Order Repair Parts ........................................................................................................ 19
Warranty .................................................................................................................................... 20
32631-3-0717 Page 3
Installer: Please leave these instructions with the owner for future
reference.
This unit complies with ANSI Z21.60 and CGA 2.26 Decorative Gas
Appliances For Installation In Solid Fuel Burning Fireplaces. Do
not burn wood or solid fuels in a replace where a decorative gas
log set is installed. This appliance is for installation only in a solid
fuel burning replace, masonry replace or manufactured replace.
WARNING: Any modication to this gas log set or to controls
can be dangerous. Improper installation or use of the gas log set
can cause serious injury or death from re, burns, explosion or
carbon monoxide poisoning.
1. Please follow all local codes regarding installation, combus-
tion and ventilation air or in the absence of local codes follow
the National Fuel Gas Code ANSI Z223.1(U.S. installation),
or CAN/CGA-B149, Installation Code (Canada installation).
2. Proper installation, burner pan location and log placement is
important to achieve optimum look and performance of your
gas log set. The logs have been designed for easy location
and placement on the grate and must be followed for proper
operation.
3. Do not operate this log set with glass doors in the closed
position. A replace screen must be in place when the log
set is burning. Adequate combustion air must be provided for
proper venting. All ames should go up and out the top of the
rebox into the ue vent. If any ames oat or curl forward into
the room do not operate appliance. Check for an open ue
and adequate combustion air into the room. A damper clamp
must be installed on the rebox damper to maintain an open
ue vent condition.
4. Young children must be carefully supervised when they are
in the same room as the gas log while in operation. Do not
place stockings, clothing or any ammable material above or
near the replace.
5. Do not substitute or use materials other than those supplied
for use with the log set.
DO NOT OPERATE THIS GAS LOG SET WITH GLASS DOORS CLOSED.
DANGER: Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING: Indicates a hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE: Addresses practices not related to personal in-
jury.
• Due to high temperatures the appliance should be located
out of trafc and away from furniture and draperies.
• Children and adults should be alerted to the hazards of
high surface temperatures and should stay away to avoid
burns or clothing ignition.
• Young children should be carefully supervised when they
are in the same room as the appliance.
• Clothing or other ammable material should not be placed
on or near the appliance.
• Do not place trash or other articles on the log set during
operation.
• During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain oils,
lms or bonding agents. These bonding agents are not
harmful but may produce annoying smoke and smells as
they are burned off during initial operation of the appliance.
This is a normal temporary occurrence. A window should
be opened during the initial bake out period.
• Keep burner and control compartment clean.
• WARNING: Before installing in a solid fuel burning
replace, the chimney ue and rebox must be cleaned
of soot, creosote, ashes and loose paint by a qualied
chimney cleaner.
• WARNING: Do not allow fans to blow directly into the
fireplace. Avoid any drafts that alter burner flame
patterns.
• WARNING: Do not use a blower insert, heat exchanger
insert or other accessory not approved for use with this
appliance.
• Installation and repair should be done by a QUALIFIED
SERVICE PERSON. The appliance should be inspected
before use and at least annually by a qualied service
person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding materials, etc. It
is imperative that control compartments, burners and
circulating air passageways of the appliance be kept
clean.
• DO NOT put anything around the replace that will obstruct
the ow of ventilation air.
• DO keep the appliance area clear and free from combustible
material, gasoline and other ammable vapors and
liquids.
• A yearly examination and cleaning of the venting system
of the solid-fuel burning replace must be performed by
a qualied agency.
• DO make a periodic visual check of pilot and burners.
Clean and replace damaged parts.
• DO NOT use this appliance if any part has been under
water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been under
water.
• Ne pas se servir de cet appareil s'il a été plongé dans
l'eau, complètement ou en partie. Appeler un technicien
qualié pour inspecter l'appareil et remplacer toute partie
du système de contrôle et toute commande qui ont été
plongés dans l'eau.
IMPORTANT SAFETY INFORMATION
32631-3-0717Page 4
Some people cannot smell well. Some people cannot smell the
odor of the chemical put into the gas. You must nd out if you
can smell the odorant in propane. Smoking can decrease your
ability to smell. Being around an odor for a time can affect your
sensitivity or ability to detect that odor. Sometimes other odors in
the area mask the gas odor. People may not smell the gas odor
or their minds are on something else. Thinking about smelling a
gas odor can make it easier to smell.
The odorant in LP-gas is colorless, and it can fade under some
circumstances. For example, if there is an underground leak, the
movement of the gas through soil can lter the odorant. Odorants
in LP-Gas also are subject to oxidation. This fading can occur if
there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into walls,
masonry and other materials and fabrics in a room. That will take
some of the odorant out of the gas, reducing its odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest gas
odor. If you detect any odor, treat it as a serious leak. Immediately
go into action as instructed earlier.
Propane (LP-Gas) is a ammable gas which can cause res
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precau-
tions which can protect both you and your family from an
accident. Read them carefully now, then review them point by
point with the members of your household. Someday when
there may not be a minute to lose, everyone's safety will depend
on knowing exactly what to do. If, after reading the following
information, you feel you still need more information, please
contact your gas supplier.
• Learn to recognize the odor of LP-gas. Your local LP-Gas
Dealer can give you a "Scratch and Sniff" pamphlet. Use it to
nd out what the propane odor smells like. If you suspect that
your LP-Gas has a weak or abnormal odor, call your LP-Gas
Dealer.
• If you are not qualied, do not light pilot lights, perform service,
or make adjustments to appliances on the LP-Gas system. If
you are qualied, consciously think about the odor of LP-Gas
prior to and while lighting pilot lights or performing service or
making adjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the
odor if there has been a leak of LP-Gas.
• Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people should
be particularly alert and careful when new tanks or cylinders
are placed in service. Odor fade can occur in new tanks, or
reinstalled old tanks, if they are lled and allowed to set too
long before relling. Cylinders and tanks which have been
out of service for a time may develop internal rust which will
cause odor fade. If such conditions are suspected to exist,
a periodic sniff test of the gas is advisable. If you have any
question about the gas odor, call your LP-gas dealer. A
periodic sniff test of the LP-gas is a good safety measure
under any condition.
• If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the
same immediate action recommended above for the occasion
when you do detect the odorized LP-Gas.
• If you experience a complete "gas out," (the container is un-
der no vapor pressure), turn the tank valve off immediately.
If the container valve is left on, the container may draw in
some air through openings such as pilot light orices. If this
occurs, some new internal rusting could occur. If the valve is
left open, then treat the container as a new tank. Always be
sure your container is under vapor pressure by turning it off
at the container before it goes completely empty or having it
relled before it is completely empty.
• Do not operate electric switches, light matches, use your
phone. Do not do anything that could ignite the gas.
• Get everyone out of the building, vehicle, trailer, or area. Do
that IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas such
as basements. When you have reason to suspect a gas leak,
keep out of basements and other low areas. Stay out until
reghters declare them to be safe.
• Use your neighbor's phone and call a trained LP-Gas service
person and the re department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
• Finally, let the service man and reghters check for escaped
gas. Have them air out the area before you return. Properly
trained LP-Gas service people should repair the leak, then
check and relight the gas appliance for you.
SOME POINTS TO REMEMBER
NO ODOR DETECTED - ODOR FADE
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That's your signal to go into immediate action!
SAFETY INFORMATION FOR USERS OF LP-GAS
32631-3-0717 Page 5
Instructions to Installer
1. Installer must leave instruction manual with owner after
installation.
2. Installer must have owner ll out and mail warranty card supplied
with the replace.
3. Installer should show owner how to start and operate the
replace.
WARNING
ANY CHANGE TO THIS APPLIANCE OR ITS CONTROLS CAN
BE DANGEROUS.
Improper installation or use of the appliance can cause se-
rious injury or death from re, burns, explosion or carbon
monoxide poisoning.
Product Components
• Burner Pan Assembly
— "M" model includes manual gas valve, regulator and safety
pilot.
— "R" model includes millivolt valve and safety thermopile
generator and on/off switch. A remote control or wall switch
accessory is available as an option for this model.
• 1 Bag of Glowing Embers (Rock Wool)
• 1 Damper Clamp
• 2 Bags Decorative Rock
Always consult your local Building Department regarding regula-
tions, codes or ordinances which apply to the installation of a vented
decorative gas log set in a solid-fuel burning replace.
This appliance is only for use with the type of gas indicated on the
rating plate.
INTRODUCTION
This series is design certied in accordance with American National
Standard/CSA Standard Z21.60 and CGA 2.26, respectively, by the
Canadian Standards Association as a Vented Decorative Appliance
and should be installed according to these instructions.
Any alteration of the original design, installed other than as
shown in these instructions or use with a type of gas not
shown on the rating plate is the responsibility of the person
and company making the change.
Important
All correspondence should refer to complete Model Number, Serial
Number and type of gas.
Notice: During initial use of the logs and branches you will detect
an odor as the logs and branches are cured.
Specications (Figure 1)
Model
Input
Btuh
** Reduced
Input
BTUH
Minimum
Front
Width
Depth Height
VSM-18* 65,000 40,000 32" 15" 22"
VSM-24* 75,000 50,000 34" 15" 22"
VSM-30* 75,000 60,000 38" 15" 22"
VSR-18† 65,000 40,000 28" 15" 22"
VSR-24† 75,000 50,000 30" 15" 22"
VSR-30† 75,000 60,000 34" 15" 22"
GENERAL INFORMATION
Model
Input
KW/H
**Reduced
Input BTUH
Minimum
Front
Width
(cm)
Depth
(cm)
Height
(cm)
VSM-18* 19.0 11.7 81.3 38.1 55.8
VSM-24* 21.9 14.6 86.4 38.1 55.8
VSM-30* 21.9 17.5 96.5 38.1 55.8
VSR-18† 19.0 11.7 71.1 38.1 55.8
VSR-24† 21.9 14.6 76.2 38.1 55.8
VSR-30† 21.9 17.5 86.4 38.1 55.8
* M Denotes manual gas valve
† R Denotes millivolt gas valve
** Attention: An additional main burner orice is provided
in instruction package envelope to reduce the input of the burner
assembly.
Gas Inlet VSM Models 3/8" (9.5mm)
Gas Inlet VSR Models 3/8" (9.5mm)
Accessories for VSM and VSR Models
Embers Kit EK-1
Accessories for VSR Models
Battery Operated Remote Control FRBC
Electric Remote FREC
Wall Switch FWS
WIDTH
HEIGHT
DEPTH
FRONT VIEW SIDE VIEW
Figure 1
32631-3-0717Page 6
Qualied Installing Agency
Installation and replacement of gas piping, gas utilization equipment
or accessories and repair and servicing of equipment shall be per-
formed only by a qualied agency. The term "qualied agency" means
any individual, rm, corporation or company which either in person
or through a representative is engaged in and is responsible for (a)
the installation or replacement of gas piping or (b) the connection,
installation, repair or servicing of equipment, who is experienced in
such work, familiar with all precautions required and has complied
with all the requirements of the authority having jurisdiction.
Commonwealth of Massachusetts: The installation must be
made by a licensed plumber or gas tter in the Commonwealth
of Massachusetts.
The installation and the provisions for combustion and ventilation
air must conform with the National Fuel Gas Code, ANSI Z223.1/
NFPA54* Canadian Installation Code CAN/CGA B149.
*Available from the American National Standards Institute, Inc. 11
West 42nd St., New York, N.Y. 10018.
High Altitude Installation
When installing this unit at an elevation above 2000 feet (in the
United States) it may be necessary to decrease the input rating by
changing the existing burner orice to a smaller size. Generally,
input should be reduced 4 percent for each 1000 feet above sea
level. However, if the heating value of the gas has been reduced,
this general rule may not apply. Check with local gas utility for proper
orice size identication.
For Canadian high altitude applications, this appliance is suitable for
installation at elevations between 0 feet (0m) and 4,500 (1,370m)
without change.
When installing this unit at an elevation above 4500 feet (1,370m)
(in Canada), check with local authorities.
Consult your local gas utility for assistance in determining the proper
orice for location.
GENERAL INFORMATION (continued)
• Turn off gas supply to replace or rebox.
• Have the replace oor and chimney professionally cleaned to
remove ashes, soot, creosote or other obstructions.
Have this cleaning performed annually after installation.
• Seal any fresh air vents or ash clean-out doors located on oor
or wall of replace. If not, drafting may cause pilot
outage or sooting. Use a heat-resistant sealant. Do not seal
chimney ue damper.
Installing Damper Clamp (Figure 2)
Remove all ashes or other debris from the replace. If the replace
is equipped with an ash dump be sure to seal the door with furnace
cement or high temperature silicone. Be sure to check the damper for
proper operation and verify that the ue passageway is open. Attach
damper clamp to the vent damper and tighten hold down bolt.
Place the clamp over the lip of the damper and tighten the hold
down bolt until the clamp is securely attached to the damper. This
will prevent the damper from accidentally closing.
Commonwealth of Massachusetts requirement for installation of
vented decorative appliance in a vented replace is the following:
In the Commonwealth of Massachusetts vent free products are
not approved.
A vented decorative gas appliance must be installed in a vented
replace only in the Commonwealth of Massachusetts. The vent
damper must be removed or welded permanently open.
Figure 2
FIREPLACE PREPARATION
32631-3-0717 Page 7
Before installing in a solid fuel burning replace, the chimney ue
and rebox must be cleaned of soot, creosote, ashes and loose
paint by a qualied chimney cleaner.
You must secure the gas log heater to the replace oor. If
not, the entire unit may move when you adjust the controls.
Movement of unit may cause shifting of the gas logs which
leads to sooting and improper burning. Grate movement
could cause a gas leak.
Special care is required if you are installing the unit into a
sunken replace. You must raise the replace oor to allow
access to gas log controls. This will insure adequate air
ow and guard against sooting. Raise the replace oor
using noncombustible materials.
1. Center the gas log in the replace or rebox. The grates must
clear the replace or rebox screen.
2. An anchor hole is provided in the two bottom side members of
the grate frame. After centering the grate correctly, mark the
hole positions on the replace/rebox oor. Drill two (2) 5/32"
diameter holes approximately 1-1/2" deep for masonry screws
or 1/8" hole for sheet metal screws.
3. Anchor the grate to the replace/rebox oor using the screws
provided.
Proper installation of the grate is essential to prevent any move-
ment of the gas logs and controls during operation.
Figure 3
BEFORE FULLY INSTALLING THE APPLIANCE
FOR FACTORY BUILT FIREPLACES
FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING
COMBUSTION PRODUCTS FROM DECORATIVE APPLIANCES
FOR INSTALLATION IN SOLID FUEL BURNING FIREPLACES.
Chimney
Height*
(ft)
Appliance Input Rate (kBTU/hr)
20 30 40 50 60 70 80
Minimum Opening** (sq. in.)
10 11.3 16.6 22.1 28.3 35.3 44.2 -
15 8.6 12.6 17.3 21.2 26.4 32.2 31.2
20 7.5 10.8 14.5 18.1 22.1 26.4 31.2
25 6.6 9.6 12.6 15.9 18.1 22.9 27.3
30 6.2 9.1 11.3 14.5 17.3 20.4 24.6
35 5.7 8.0 10.8 13.2 15.9 18.9 22.1
40 5.3 7.5 10.2 12.6 15.2 18.1 20.4
Chimney
Height*
(m)
Appliance Input Rate KW/HR)
5.9 8.8 11.7 14.6 17.6 20.5 23.4
Minimum Opening** (sq. in.)
3.05 72.9 107.1 142.6 182.6 227.8 285.2 -
4.57 55.5 81.3 111.6 136.8 170.3 207.8 248.4
6.10 48.4 69.7 93.6 116.8 142.6 170.3 201.3
7.62 42.6 61.9 81.3 102.6 116.8 147.8 176.1
9.14 40.0 58.7 72.9 93.6 111.6 131.6 158.7
10.67 36.8 51.6 69.7 85.2 102.6 121.9 142.6
12.19 34.2 48.4 65.8 81.3 98.1 116.8 131.6
* Height is from hearth to top of chimney and the minimum height is
10 feet (3.05m).
** Chart shows minimum opening (sq. in.) (cm
2
) for given height and
input rate.
FOR MASONRY BUILT FIREPLACES
FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING
COMBUSTION PRODUCTS FROM DECORATIVE APPLIANCES
FOR INSTALLATION IN SOLID FUEL BURNING FIREPLACES.
Chimney
Height*
(ft)
Appliance Input Rate (kBTU/hr)
20 30 40 50 60 70 80
Minimum Opening** (sq. in.)
6 17.6 25.7 33.8 41.7 49.2 56.6 64.0
8 16.5 23.7 31.2 38.7 45.5 52.4 59.7
10 15.1 21.7 28.7 35.2 41.7 48.2 54.3
15 14.1 19.9 26.1 32.0 37.7 43.2 48.8
20 12.9 18.5 23.7 28.8 34.3 39.8 44.4
30 12.2 16.9 21.6 26.5 31.2 35.9 40.3
Chimney
Height*
(m)
Appliance Input Rate KW/HR)
5.9 8.8 11.7 14.6 17.6 20.5 23.4
Minimum Opening** (sq. in.)
1.83 113.6 165.8 218.1 269.0 317.4 365.2 412.9
2.44 106.5 152.9 201.3 249.7 293.6 338.1 385.2
3.05 97.4 140.0 185.2 227.1 269.0 311.0 350.3
4.57 91.0 128.4 168.4 206.5 243.2 278.7 314.8
6.10 83.2 119.4 152.9 185.8 221.3 256.8 286.5
9.14 78.7 109.0 139.4 171.0 201.3 231.6 260.0
* Height is from hearth to top of chimney and the minimum height is 6
feet (1.83m).
** Chart shows minimum opening (sq. in.) (cm
2
) for given height and
input rate.
32631-3-0717Page 8
Check all local codes for requirements, especially for the size and
type of gas supply line required.
NOTICE: Never use plastic pipe. Check to conrm whether your
local codes allow copper tubing or galvanized.
NOTICE: Since some municipalities have additional local codes, it is
always best to consult your local authority and installation code.
Installing a New Main Gas Shut-Off
Each appliance should have its own manual gas shut-off.
In the state of Massachusetts the gas shut-off must be a T handle type.
A manual main gas shut-off should be located in the vicinity of the
unit. Where none exists, or where its size or location is not adequate,
contact your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant
to the action of liqueed petroleum gases. The gas lines must be
checked for leaks by the installer. This should be done with a soap
solution watching for bubbles on all exposed connections, and if
unexposed, a pressure test should be made.
Never use an exposed ame to check for leaks. Appliance must
be disconnected from piping at inlet of control valve and pipe
capped or plugged for pressure test. Never pressure test with
appliance connected; control valve will sustain damage!
A gas valve and ground joint union should be installed in the gas
line upstream of the gas control to aid in servicing. It is required by
the National Fuel Gas Code that a drip line be installed near the gas
inlet. This should consist of a vertical length of pipe tee connected
into the gas line that is capped on the bottom in which condensation
and foreign particles may collect.
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings
— ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction. The state of Massachusetts requires that a exible
appliance connector cannot exceed three feet in length.
Figure 4
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a 1/8" (3.175mm)
N.P.T. plugged tapping, accessible for test gauge connection, must
be placed immediately upstream of the gas supply connection
to the appliance.
2. The appliance and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping system
by closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal
to or less than 1/2 psig (3.5 kPa).
Attention! If one of the procedures results in pressures in excess
of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will
result in a hazardous condition.
Checking Manifold Pressure
VSR Natural gas models will have a manifold pressure of approxi-
mately 3.5" w.c. (.871kPa) at the pressure regulator outlet with the
inlet pressure to the pressure regulator from a minimum of 4.5" w.c.
(1.120kPa) for the purpose of input adjustment to a maximum of
10.5" w.c. (2.615kPa). VSM Natural gas models will have a mani-
fold pressure of approximately 4.5" w.c. (1.12kPa) at the pressure
regulator outlet with the inlet pressure to the pressure regulator
from a minimum of 7.0" w.c. (1.74kPa) for the purpose of input
adjustment to a maximum of 10.5" w.c. (2.615kPa). VSR and VSM
Propane gas models will have a manifold pressure approximately
10.0" w.c. (2.49kPa) at the pressure regulator outlet with the inlet
pressure to the pressure regulator from a minimum of 11.0" w.c.
(2.739kPa) for the purpose of input adjustment to a maximum of
13.0" w.c. (3.237kPa).
VSM
NOTICE: A test gage connection is located downstream of the gas
appliance pressure regulator for measuring gas pressure. The con-
nection is a 1/8 inch 3mm) N.P.T. plugged tapping.
VSR
NOTICE: The gas control is equipped with a captured screw type
pressure test point, therefore it is not necessary to provide a 1/8"
test point up stream of the control.
GAS SUPPLY
Recommended Gas Pipe Diameter
Pipe
Length
Schedule 40 Pipe
Inside Diameter
Tubing, Type L
Outside Diameter
Nat. L.P. Nat. L.P.
0-10 feet
0-3 meters
1/2”
12.7mm
3/8”
9.5mm
1/2”
12.7mm
3/8”
9.5mm
10-40 feet
4-12 meters
1/2”
12.7mm
1/2”
12.7mm
5/8”
15.9mm
1/2”
12.7mm
40-100 feet
13-30 meters
1/2”
12.7mm
1/2”
12.7mm
3/4”
19mm
1/2”
12.7mm
100-150 feet
31-46 meters
3/4”
19mm
1/2”
12.7mm
7/8”
22.2mm
3/4”
19mm
32631-3-0717 Page 9
Placement of the glowing embers (rock wool) is very individual and
light coverage of the areas indicated will provide your best effects.
We recommend separation of the rock wool by hand and make your
coverage as light and uffy as possible.
Place just enough embers on the burner to obtain the glow and a
gold, yellow ame.
Do not place embers (rock wool) over large ports in rear portion
of burner.
Rock wool should not be placed in the area of the pilot assembly.
Placing Lava Rock in Front of Burner on Fireplace Floor
Spread lava rocks on replace oor in front of the burner pan. The
lava rocks are for decorative effect and are not required for replace
operation.
ATTENTION: DO NOT PLACE LAVA ROCKS ON BURNER,
LOGS OR ROCK WOOL. THE LAVA ROCKS SHOULD ONLY
BE PLACED ON THE FIREPLACE FLOOR.
Figure 5
PLACEMENT OF GLOWING EMBERS AND LAVA ROCK
Flames from the pilot (right back side of the pan burner) as well
as the main ame should be visually checked as the log set is
installed.
In normal operation at full rate after 10 to 15 minutes, the ame
appearance should be sets of yellow ames.
NOTICE: all ames will be random by design, ame height will go
up and down.
Avoid any drafts that alter burner ame patterns. Do not allow fans to
blow directly into replace. Do not place a blower inside the burner
area of the rebox. Ceiling fans may create drafts that alter ame
patterns. Sooting and improper burning will result.
During manufacturing, fabricating and shipping, various components
of this appliance are treated with certain oils, lms or bonding agents.
These chemicals are not harmful, but may produce annoying smoke
and smells as they are burned off during the initial operation of the
appliance, possibly causing headaches or eye or lung irritation. This
is a normal and temporary occurrence.
The initial break-in operation should last 2-3 hours with the burner
at the highest setting. Provide maximum ventilation by opening
windows or doors to allow odors to dissipate. Any odors remaining
after this initial break-in will be slight and will disappear with
continued use.
“VSM” MANUAL VALVE MODELS
BURNER TO BE CENTERED AND
AS FAR BACK AS POSSIBLE
Manual - Figure 6
Millivolt - Figure 7
OPERATION INSTRUCTIONS/FLAME APPEARANCE
32631-3-0717Page 10
1. Push in gas control knob slightly and turn clockwise
to “OFF.” Do not force.
1. STOP! Read the safety
information above.
2. Push in manual gas con-
trol knob slightly and turn
clockwise to
"OFF". Do not force.
NOTE: Knob cannot be
turned from "PILOT" to
"OFF" unless knob is
pushed in slightly. Do not
force.
3. Wait ten (10) minutes to clear out any gas. Then smell
for gas, including near the oor. If you smell gas,
STOP! Follow “B” in the safety information above. If
you don't smell gas, go to the next step.
4. Find pilot - follow metal tube from gas control. The
pilot is in front of middle
log on the right side.
5. Turn manual gas control
knob counterclockwise
to “PILOT.”
6. Push in control knob all
the way and hold in. Im-
mediately light the pilot with a match and the lighter
rod that is provided with the burner. Continue to hold
the control knob in for about one (1) minute after the
pilot is lit. Release knob and it will pop back up. Pilot
should remain lit. If it goes out, repeat steps 2 through
6.
• If knob does not pop up when released, stop and
immediately call a qualied service technician or
gas supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your service
technician or gas supplier.
7. Turn manual gas control knob counterclockwise
to “ON.”
VSM-(18, 24, 30) LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a re or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the oor because some
gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the re
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualied service
technician. Force or attempted repair may result in a re
or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualied service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING INSTRUCTIONS
WARNING
• Any glass doors shall be opened when the appliance is in operation.
• A replace screen must be in place when the appliance is operating and, unless other provisions for
combustion air are provided, the screen shall have an opening(s) for introduction of combustion air.
TO TURN OFF GAS TO APPLIANCE
GAS CONTROL
KNOB SHOWN
IN “PILOT” POSITION
32631-3-0717 Page 11
1. STOP! Read the safety information
above.
2. Set the ON/OFF switch to "OFF."
3. Turn off all electric power to the appli-
ance (if applicable).
4. Push in gas control knob slightly and turn
clockwise to "OFF."
5. Wait ten (10) minutes to clear out any
gas. Then smell for gas, including near
the oor. If you smell gas, STOP! follow
"B" in the safety information above. If you
do not smell gas, go to the next step.
NOTE: Knob cannot be turned from "PI-
LOT" to "OFF" unless knob is pushed in
slightly. Do not force.
6. Find pilot - follow metal tube from gas
control. The pilot is in front of the middle
log on the right side.
7. Turn gas control knob counterclockwise
to "PILOT."
8. Push in control knob all the way and hold in. Immediately
light the pilot with a match and lighter rod that is provided
with the burner. Continue to hold the control knob in for about
one (1) minute after the pilot is lit. Release knob, and it will
pop back up. Pilot should remain lit. If it goes out, repeat
steps 4 through 8.
If knob does not pop up when released, stop and immediately
call a qualied service technician or gas supplier.
If the pilot will not stay lit after several tries, turn the gas con-
trol knob to "OFF" and call your service technician or gas
supplier.
9. Turn gas control knob counter clockwise to "ON."
10. Set the ON/OFF switch to "ON."
1. Set the ON/OFF switch to "OFF".
2. Push in gas control knob slightly and turn clockwise
to "OFF". Do not force.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the oor because some
gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the re
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don't try to repair it; call a qualied ser-
vice technician. Force or attempted repair may result
in a re or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
WARNING
• Any glass doors shall be opened when the appliance is in operation.
• A replace screen must be in place when the appliance is operating and, unless other provisions for combustion air
are provided, the screen shall have an opening(s) for introduction of combustion air.
GAS CONTROL
KNOB SHOWN IN
"OFF" POSITION.
VSR-(18, 24, 30) LIGHTING INSTRUCTIONS
TO TURN OFF GAS TO APPLIANCE
LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a re or explosion may result
causing property damage, personal injury or loss of life.
32631-3-0717Page 12
PILOT AND MAIN BURNER FLAME CHARACTERISTICS
Pilot Flame Pattern (Figure 8)
Figure 8 shows a correct pilot ame pattern. The correct ame will
be blue and will extend beyond the thermocouple/thermopile. The
ame will surround the thermocouple/thermopile just below the
tip. A slight yellow ame may occur where the pilot ame and main
burner ame meet.
After use, cleaning of the pilot burner may be required for the proper
ame. The pilot orice can be cleaned with high pressure air or
by placing under running water. Pilot orice must be dry before
replacement. Use a pipe cleaner to clean inside the pilot after the
pilot orice has been removed.
To Remove Pilot Orice
1. Disconnect the pilot supply line at the pilot burner.
2. Remove pilot orice from pilot burner. It may be necessary to
tap on pilot burner in order to remove the pilot orice.
Pilot Flame Pattern
Figure 8
If pilot ame pattern is incorrect
• See Troubleshooting, page 14
Main Burner Flame Pattern
The main burner ame will be completely yellow.
Main Burner Flame Ignition and Extinction
When the main burner is ignited it will take a few seconds for the
full ame pattern to develop.
When the main burner is extinguished it will take a few seconds for
the ames to disappear. It is normal to have the ames burn down
near the rock wool, as the remaining gas is burned.
32631-3-0717 Page 13
Thermostats are not approved on vented decorated
appliances.
Label all wires prior to disconnection when servicing controls. Wiring
errors can cause improper and dangerous operation. Verify proper
operation after servicing.
VSR gas valve does not require 24 or 110 volts. See Figure 9 to
provide optional wall switch or remote control.
It is important to use wire of a gauge proper for the length of the wire:
RECOMMENDED WIRE GAUGES
Maximum Length Wire Gauge
1' to 10' 18
10' to 25' 16
25' to 35' 14
Use the two leads (black wires) from ON/OFF switch to attach
optional components.
Check System Operation
Millivolt system and all individual components may be checked with
a millivolt meter 0-1000 MV range.
750 Millivolt System
When you ignite the pilot, the thermocouple produces millivolts
(electrical current) which energizes the magnet in the gas valve.
After 30 seconds to 1 minute time period you can release the gas
control knob and the pilot will stay ON. Allow your pilot ame to
operate an additional one (1) to two (2) minutes before you turn the
gas control knob from the PILOT position to the ON position. This
time period allows the millivolts (electrical current) to buildup to a
sufcient level allowing the gas control to operate properly.
Millivolt Control
The valve regulator controls the burner pressure which should be
checked at the pressure test point. Turn captured screw counter
clockwise 2 or 3 turns and then place tubing to pressure gauge over
test point (Use test point “A” closest to control knob). After taking
pressure reading, be sure and turn captured screw clockwise rmly
to re-seal. Do not over torque. Check for gas leaks.
Remote Receiver -VSR-(18, 24, 30)
Use the following steps to place the remote receiver adjacent to
the gas valve.
Attention:
1. The remote receiver can not be placed behind the gas valve
and burner assembly.
2. When facing the appliance, the remote receiver must be placed
in the right side rebox, toward the front.
NOTICE: Do not let remote control receiver come in contact with
burner assembly.
Refer to remote control installation and operating instructions for
more details on remote control.
VSR Wiring Diagram (Figure 9)
Figure 9
VSR
NOTICE: (Wiring harness located in envelope)
Connect the 2 - 1/4" terminals onto the TH and TH/TP terminals
on valve. Place decorative log to right of the gas valve and burner
assembly. When connecting to remote receiver, cut off 1/4" terminals
from wires attached to ON/OFF switch. Strip wires back about 1/4".
Connect stripped ends into remote receiver.
Keep the control compartment, logs and burner area surrounding
the logs clean.
THE LOGS CAN GET VERY HOT— HANDLE ONLY WHEN
COOL.
Always keep the appliance area clear and free from combustible
materials, gasoline, and other ammable vapors and liquids.
Never obstruct the ow of combustion and ventilation air. Keep the
front of the appliance clear of all obstacles and materials.
Inspecting Venting System
A vented replace venting system is designed and constructed
to develop a positive ow adequate to remove ue gases to the
outside atmosphere.
Any foreign objects in the venting system, may cause spillage of
the ue gases into the room.
Periodic examination and/or cleaning of the venting system of the
solid-fuel burning replace must be done by a qualied service
person. Visually inspect the damper and ue area for excessive
soot build-up. This soot (carbon) may be removed by brushing with
a soft bristle brush.
WIRING
CLEANING AND SERVICING
32631-3-0717Page 14
SYMPTOMS-POSSIBLE CAUSES AND CORRECTIONS
1. Match will not light pilot.
a. Main shut-off valve closed.
• Make sure that the shut-off valve located on the pipe
supplying gas to the replace is open.
b. Air in the gas line.
• Light a match, turn valve knob to "PILOT" position and
depress, keep match near pilot burner until it lights.
c. Valve knob in "OFF" position.
• Turn valve knob to "PILOT" position and depress, keep
match near pilot burner until it lights.
d. Pilot orice plugged up, not allowing gas to ow.
• This repair requires tools and some degree of experience.
Ask serviceman for assistance.
e. No gas supply to the replace.
• Check plumbing to see if gas replace has been hooked
up to the gas supply line.
• Propane tanks is empty.
2. Pilot will not stay lit after carefully following lighting instruc-
tions for VSR—Models.
a. Defective pilot generator (thermopile), remote wall switch.
• Check pilot ame. Must impinge on thermopile. Clean
and or adjust pilot for maximum ame impingement on
thermopile.
• Be sure wire connections from thermopile at gas valve
terminals are tight and thermopile is fully inserted into
pilot bracket.
• One of the wall switch wires may be grounded. Remove
wall switch wires from valve terminals if pilot now stays
lit, trace wall switch wiring for ground. May be grounded
to appliance or gas supply.
• Check thermopile with millivolt meter. Take reading at
thermopile terminals of gas valve. Should read 325 mil-
livolts minimum while holding valve knob depressed in pilot
position and wall switch "Off." Replace faulty thermopile
if reading is below specied minimum.
b. Defective automatic valve operator — Turn valve knob to
"On." Place wall switch to "On" millivolt meter should read
greater than 100 M.V. If the reading is okay and the burner
does not come on, replace the gas valve.
c. Defective thermopile.
• Check all connections and try.
• If still not operating, disconnect lead between thermo-
couple switch and valve operator. Then disconnect lead
to pilot magnet and connect to valve operator terminal
(TP, TH). If pilot remains lit fault lies with thermocouple.
Check that bulb is in proper location. If still not working
replace thermocouple (see drawing in manual for ad-
ditional information).
3. Pilot burning, no gas to burner, valve knob "On," wall switch
"On."
a. Wall switch or wires defective.
• Check wall switch and wires for proper connections.
Jumper wire cross terminals at wall switch, if burner
comes on, replace defective wall switch. If okay, jumper
wires cross wall switch wires at valve, if burner comes
on, wires are faulty or connections are bad.
b. Thermopile may not be generating sufcient millivoltage.
• Replace.
c. Plugged burner orice.
• Check burner orice for debris and remove.
4. Pilot will not stay lit after carefully following lighting instruc-
tions for VSM—Models.
a. Defective thermocouple.
• Check that pilot ame impinges on thermocouple. Clean
and/or adjust pilot for maximum ame impingement.
• Ensure that the thermocouple connection at the gas valve
is fully inserted and tight (hand tight plus 1/4 turn) faulty
thermopile if reading is below specied minimum.
• Disconnect the thermocouple from the valve, place one
millivolt meter lead wire on the tip of the thermocouple and
the other meter lead wire on the thermocouple copper lead.
Start the pilot and hold the valve knob in. If the millivolt
reading is less than 15 mv, replace the thermocouple.
b. Defective valve.
• If thermocouple is producing more than 15 millivolts,
replace faulty valve.
5. Frequent pilot outage problem.
a. Pilot ame may be too low or blowing (high) causing the pilot
to drop out.
• Clean and/or adjust ame for maximum ame impinge-
ment on thermopile or thermocouple.
6. Main burner ame is too low or too high.
a. Check inlet supply pressure for "M" and "R" models.
b. Check manifold pressure on gas valve for "R" models and
inlet regulator on "M" models.
TROUBLESHOOTING
32631-3-0717 Page 15
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
PARTS LIST
INDEX
NO.
PART
NO.
DESCRIPTION
COMMON PARTS
1 15426 REAR LOG SUPPORT (18)
1 15427 REAR LOG SUPPORT (24)
1 15428 REAR LOG SUPPORT (30)
2 11376 BURNER SUPPORT - LEFT
3 P-271 ORIFICE FITTING
5 R-5675 AIR SHUTTER-LPG
5 R-5676 AIR SHUTTER-NAT
6 15415 PILOT BRACKET
7 R-7158 PILOT ASSEMBLY-NAT
7 R-7157 PILOT ASSEMBLY-LPG
8 18838 BURNER ASSEMBLY (18)
8 17370 BURNER ASSEMBLY (24)
8 17386 BURNER ASSEMBLY (30)
20 11370*
GRATE ASSEMBLY (18" MODELS)
(2 REQ'D)
20 16178*
GRATE ASSEMBLY (24" & 30" MODELS)
(2 REQ'D)
*Requires 2/Grate ASM of R9628 Clips
VSR-18,24,30
4 P-265 ORIFICE-LPG (18) (40,000 BTU)
4 P-209 ORIFICE-NAT (18) (40,000 BTU)
4 P-256 ORIFICE-LPG (18) (65,000 BTU)
4 P-274 ORIFICE-NAT (18) (65,000 BTU)
4 P-257 ORIFICE-LPG (24&30) (75,000 BTU)
4 P-276 ORIFICE-LPG (24) (50,000 BTU)
4 P-279 ORIFICE-NAT (24&30) (75,000 BTU)
4 P-280 ORIFICE-NAT (24) (50,000 BTU)
4 P-181 ORIFICE-LPG (30) (60,000 BTU)
4 P-283 ORIFICE-NAT (30) (60,000 BTU)
9 26291 BURNER SUPPORT - RIGHT
10 26294 VALVE BRACKET
11 R7195 BRASS MALE CONNECTOR
12 R10408 GAS VALVE - LPG
12 R10407 GAS VALVE - NAT
NS R1259 3/8" ELBOW 90 STREET
NS R-5910 SWITCH LOG ASSEMBLY
NS R-5699 WIRE HARNESS
NS R-11558 ON/OFF SWITCH
NS 26282 TUBING VALVE TO PILOT
NS 26283 TUBING VALVE TO BURNER
NS 15496 ROCK WOOL
NS 11788 DECORATIVE ROCK
NS R-2809 DAMPER CLAMP
NS R-734 LIGHTER ROD
NS R-1054 THERMOPILE
VSM-18,24,30
4 P-265 ORIFICE-LPG (18) (40,000 BTU)
4 P-211 ORIFICE-NAT (18) (40,000 BTU)
4 P-256 ORIFICE-LPG (18) (65,000 BTU)
4 P-273 ORIFICE-NAT (18) (65,000 BTU)
4 P-257 ORIFICE-LPG (24&30) (75,000 BTU)
4 P-276 ORIFICE-LPG (24) (50,000 BTU)
4 P-277 ORIFICE-NAT (24&30) (75,000 BTU)
4 P-278 ORIFICE-NAT (24) (50,000 BTU)
4 P-181 ORIFICE-LPG (30) (60,000 BTU)
4 P-282 ORIFICE-NAT (30) (60,000 BTU)
9 26291 BURNER SUPPORT - RIGHT
11 R-7195 BRASS MALE CONNECTOR
13 15413 REGULATOR MOUNTING BRACKET
14 R-7159 INLET REGULATOR - LPG
14 R-7160 INLET REGULATOR - NAT
15 P-133 NIPPLE 2"
16 P-135 3/8" ELBOW
17 P-239 NIPPLE 1 1/2"
18 FG10007 GAS VALVE
19 32621 COVER PLATE
NS 32620 TUBING VALVE TO PILOT
NS 32622 TUBING VALVE TO BURNER
NS 15496 ROCK WOOL
NS 11788 DECORATIVE ROCK
NS R-2809 DAMPER CLAMP
NS R-734 LIGHTER ROD
NS R-2256 THERMOCOUPLE
NS - NOT SHOWN
INDEX
NO.
PART
NO.
DESCRIPTION
32631-3-0717Page 16
1
2
3
4
5
6
7
8
9
9
12
10
11
13
14
15
16
17
11
18
19
20
PARTS VIEW
32631-3-0717 Page 17
1. If applicable, turn OFF gas supply to vented decorative log
set.
2. If applicable, remove gas supply line from vented decorative
log set.
3. For VSM-(18, 24, 30) only, remove Natural gas inlet regulator
from burner assembly.
3. For VSR-(18, 24, 30) only, remove regulator cap and blue
conversion screw from HI-LO knob on gas valve.
4. For VSM-(18, 24, 30) only, install Propane (LP) gas inlet
regulator marked 10.0 onto burner assembly.
4. For VSR-(18, 24, 30) only, install Propane (LP) gas pink
conversion screw into HI-LO knob on gas valve. Assure that
conversion screw is nger tight (refer to Honeywell conversion
instructions which are included in conversion kit). Install new
regulator cap over pink conversion screw.
5. Remove Natural gas main burner orice from orice tting.
Save the Natural gas main burner orice from the appliance
for future use.
Attention: Use appropriate main burner orice for NORMAL
input or REDUCED input.
6. Install Propane (LP) gas main burner orice into orice tting
for NORMAL input.
For VSM-18 or VSR-18, install one Propane (LP) gas main
burner orice marked 41 for 65,000 BTUH input.
For VSM-24 or VSR-24, install one Propane (LP) gas main
burner orice marked 40 for 75,000 BTUH input.
For VSM-30 or VSR-30, install one Propane (LP) gas main
burner orice marked 40 for 75,000 BTUH input.
6. Install Propane (LP) gas main burner orice into orice tting
for REDUCED input.
For VSM-18 or VSR-18, install one Propane (LP) gas main
burner orice marked 49 for 40,000 BTUH input.
For VSM-24 or VSR-24, install one Propane (LP) gas main
burner orice marked 45 for 50,000 BTUH input.
For VSM-30 or VSR-30, install one Propane (LP) gas main
burner orice marked 43 for 60,000 BTUH input.
7. Remove pilot tubing from pilot burner.
8. Remove Natural gas pilot orice from pilot burner. Save the
Natural gas pilot orice removed from the appliance for future
use.
9. Insert Propane (LP) gas pilot orice marked 8 into pilot
burner.
10. Attach pilot tubing into pilot burner.
11. Connect gas supply line to vented decorative log set.
12. Attach R-1322, conversion label and R-1321, gas conversion
label to the 4 3/4" x 7 1/4" metal plate supplied in conversion
kit. Attach 4 3/4" x 7 1/4" metal plate to metal chain which is
attached to base assembly.
13. Pressure Testing of the Gas Supply System
a. To check the inlet pressure to the gas valve, a 1/8"
(3mm) N.P.T. plugged tapping, accessible for test gauge
connection, must be placed immediately upstream of the
gas supply connection to the appliance.
b. The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa).
c. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at
test pressures equal to or less than 1/2 psig (3.5 kPa).
Attention! If one of the above procedures results in
pressures in excess of 1/2 psig (14" w.c.) (3.5 kPa) on
the appliance gas valve, it will result in a hazardous
condition.
14. Turn on Propane (LP) gas supply to vented decorative log
set.
15. All gas connections must be checked for gas leaks by the
person (qualied agency) making the gas conversion. This
should be done with a soap solution watching for bubbles on
all exposed connections, and if unexposed, a pressure test
must be done.
16. Check the appropriate manifold pressure for the vented
decorative log set according to Gas Supply on Page 8 in this
manual.
17. Check pilot burner ame pattern according to Pilot and Main
Burner Flame Characteristics on Page 12 in this manual.
18. Check main burner ame pattern according to Pilot and Main
Burner Flame Characteristics on Page 12 in this manual.
19. Gas conversion is completed.
Attention: The Propane (LP) gas conversion kit must be
ordered from Empire Comfort Systems, Inc.
PROPANE (LP) GAS CONVERSION INSTRUCTIONS
32631-3-0717Page 18
1. If applicable, turn OFF gas supply to vented decorative log
set.
2. If applicable, remove gas supply line from vented decorative
log set.
3. For VSM-(18, 24, 30) only, remove Propane gas inlet regulator
from burner assembly.
3. For VSR-(18, 24, 30) only, remove regulator cap and pink
conversion screw from HI-LO knob on gas valve.
4. For VSM-(18, 24, 30) only, install Natural gas inlet regulator
marked 4.5 onto burner assembly.
4. For VSR-(18, 24, 30) only, install Natural gas blue conversion
screw into HI-LO knob on gas valve. Assure that conversion
screw is nger tight (refer to Honeywell conversion instructions
which are included in conversion kit). Install new regulator cap
over blue conversion screw.
5. Remove Propane (LP) main burner orice from orice tting.
Save the Propane (LP) gas main burner orice from the appliance
for future use.
Attention: Use appropriate main burner orice for NORMAL
input or REDUCED input.
6. Install Natural gas main burner orice into orice tting for
NORMAL input.
For VSM-18, install one Natural gas main burner orice marked
22 for 65,000 BTUH input.
For VSM-24, install one Natural gas main burner orice marked
16 for 75,000 BTUH input.
For VSM-30, install one Natural gas main burner orice marked
16 for 75,000 BTUH input.
For VSR-18, install one Natural gas main burner orice marked
20 for 65,000 BTUH input.
For VSR-24, install one Natural gas main burner orice marked
14 for 75,000 BTUH input.
For VSR-30, install one Natural gas main burner orice marked
14 for 75,000 BTUH input.
6. Install Natural gas main burner orice into orice tting for
REDUCED input.
For VSM-18, install one Natural gas main burner orice marked
32 for 40,000 BTUH input.
For VSM-24, install one Natural gas main burner orice marked
28 for 50,000 BTUH input.
For VSM-30, install one Natural gas main burner orice marked
24 for 60,000 BTUH input.
For VSR-18, install one Natural gas main burner orice marked
31 for 40,000 BTUH input.
For VSR-24, install one Natural gas main burner orice marked
29 for 50,000 BTUH input.
For VSR-30, install one Natural gas main burner orice marked
26 for 60,000 BTUH input.
7. Remove pilot tubing from pilot burner.
8. Remove Propane (LP) gas pilot orice from pilot burner. Save
the Propane (LP) gas pilot orice removed from the appliance
for future use.
9. Insert Natural gas pilot orice marked 12 into pilot burner.
10. Attach pilot tubing into pilot burner.
11. Connect gas supply line to vented decorative log set.
12. Attach R-1322, conversion label and R-1320, gas conversion
label to the 4 3/4" x 7 1/4" metal plate supplied in conversion
kit. Attach 4 3/4" x 7 1/4" metal plate to metal chain which is
attached to base assembly.
13. Pressure Testing of the Gas Supply System
a. To check the inlet pressure to the gas valve, a 1/8" (3mm)
N.P.T. plugged tapping, accessible for test gauge connec-
tion, must be placed immediately upstream of the gas supply
connection to the appliance.
b. The appliance and its individual shutoff valve must be dis-
connected from the gas supply piping system during any
pressure testing of that system at test pressures in excess
of 1/2 psig (3.5 kPa).
c. The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa).
Attention! If one of the above procedures results in pressures
in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance
gas valve, it will result in a hazardous condition.
14. Turn on Natural gas supply to vented decorative log set.
15. All gas connections must be checked for gas leaks by the
person (qualied agency) making the gas conversion. This
should be done with a soap solution watching for bubbles on
all exposed connections, and if unexposed, a pressure test
must be done.
16. Check the appropriate manifold pressure for the vented
decorative log set according to Gas Supply on Page 8 in this
manual.
17. Check pilot burner ame pattern according to Pilot and Main
Burner Flame Characteristics on Page 12 in this manual.
18. Check main burner ame pattern according to Pilot and Main
Burner Flame Characteristics on Page 12 in this manual.
19. Gas conversion is completed.
Attention: The Natural gas conversion kit must be ordered from
Empire Comfort Systems, Inc.
NATURAL GAS CONVERSION INSTRUCTIONS
32631-3-0717 Page 19
To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.
com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the
nature of the problem with the unit.
To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.
This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com.
Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original
Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.
MASTER PARTS DISTRIBUTOR LIST
Parts Not Under Warranty
Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distribu-
tors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the
service person/dealer.
Warranty Parts
Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for
warranty parts.
All parts listed in the Parts List have a Part Number. When ordering parts, rst obtain the Model Number and Serial Number from the
name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the fol-
lowing illustration and part list. Be sure to give all this information . . .
Appliance Model Number Part Description
Appliance Serial Number Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, res and all causes beyond our control.
HOW TO ORDER REPAIR PARTS
Dey Distributing
1401 Willow Lake Boulevard
Vadnais Heights, MN 55101
Phone: 651-490-9191
Toll Free: 800-397-1339
Website: www.deydistributing.com
Parts: Heater, Hearth and Grills
F. W. Webb Company
200 Locust Street
Hartford, CT 06114
Phone: 860-722-2433
Toll Free: 800-243-9360
Fax: 860-293-0479
Toll Free Fax: 800-274-2004
Websites: www.fwwebb.com & www.victormfg.com
Parts: Heater, Hearth and Grills
East Coast Energy Products
10 East Route 36
West Long Branch, NJ 07764
Phone: 732-870-8809
Toll Free: 800-755-8809
Fax: 732-870-8811
Website: www.eastcoastenergy.com
Parts: Heater, Hearth and Grills
32631-3-0717Page 20
WARRANTY
Empire Comfort Systems Inc. warranties this hearth product to be free from defects at the time of purchase and for the periods specied
below. Hearth products must be installed by a qualied technician and must be maintained and operated safely, in accordance with the
instructions in the owner’s manual. This warranty applies to the original purchaser only and is not transferable. All warranty repairs must
be accomplished by a qualied gas appliance technician.
Limited Three-Year Parts Warranty – All Other Components
(Except Remote Controls, Thermostats, Accessories and Replacement Parts)
Should any part fail because of defective workmanship or material within three years from the date of purchase, Empire will
repair or replace at Empire’s option.
Limited One-Year Parts Warranty – Remote Controls, Thermostats, Accessories, and Parts
Should any remote control, thermostat, accessory, or other part fail because of defective workmanship within one year from
the date of purchase, Empire will repair or replace at Empire’s option.
Duties Of The Owner
The appliance must be installed by a qualied installer and operated in accordance with the instructions furnished with the
appliance. A bill of sale, cancelled check, or payment record should be kept to verify purchase date and establish warranty
period. Ready access to the appliance for service.
What Is Not Covered
Damages that might result from the use, misuse, or improper installation of this appliance.
Travel, diagnostic costs and freight charges on warranted parts to and from the factory.
Claims that do not involve defective workmanship or materials.
Unauthorized service or parts replacements.
Removal and reinstallation cost.
Inoperable due to improper or lack of maintenance.
How To Get Service
To make a claim under this warranty, please have your receipt available and contact your installing dealer. Provide the dealer
with the model number, serial number, type of gas, and purchase verication. The installing dealer is responsible for providing
service and will contact the factory to initiate any warranted parts replacements. Empire will make replacement parts available
at the factory. Shipping expenses are not covered.
If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations Department,
Empire Comfort Systems Inc., PO Box 529, Belleville, Illinois 62222, or send an e-mail to [email protected] with
“Consumer Relations” in the subject line.
Your Rights Under State Law
This warranty gives your specic legal rights, and you may also have other rights, which vary from state to state.
www.empirecomfort.com
Empire Comfort Systems Inc.
Belleville, IL
If you have a general question
about our products, please e-mail
us at [email protected].
If you have a service or repair
question, please contact your dealer.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
White Mountain Hearth Vented Slope Glaze Burner (VFM/VSR18/24/30) Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
Empire VSM-18-1 Le manuel du propriétaire
-
Empire Comfort Systems MANTIS BP28 Series Le manuel du propriétaire
-
resideo WT8840B1000 Mode d'emploi
-
Superior Fireplaces DRI2000 Mode d'emploi
-
Breckwell Hearth AH2613i Manuel utilisateur
-
Jotul Jtul GI 425 DV Manuel utilisateur
-
SCAN 45i Installation And Operation Instructions Manual
-
Majestic fireplaces Woodland UVLC24RN Installation And Operating Instructions Manual
-
NAPOLEON GL22N Manuel utilisateur
-