NAPOLEON GL22N Manuel utilisateur

Marque: NAPOLEON

Modèle: GL22N

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.33A

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030



SAFETY INFORMATION

WARNING

If the information in these instructions are

not followed exactly, a ﬁ re or explosion

may result causing property damage,

personal injury or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier from

a neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier,

call the ﬁ re department.

- Installation and service must be performed by a

qualiﬁ

ed installer, service agency or the supplier.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

$10.00

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁ ed kit is used.

CERTD

GL22

GL28

GL32

W415-1101 / D / 08.28.18

CERTIFIED UNDER: ANSI Z21.60 / CSA 2.26 DECORATIVE GAS APPLIANCES FOR INSTALLATION IN SOLID-FUEL BURNING APPLIANCES

GL22N, GL28N, GL32N

NATURAL GAS

GL22P, GL28P, GL32P

PROPANE

Logs, see “LOG PLACEMENT” section.

Batteries, see “BATTERY

INSTALLATION” and

“BATTERY REPLACEMENT”

section.

Rating Plate, see

“RATING PLATE

INFORMATION”

section.

Media, see “SAND OR

GLASS MEDIA PLACEMENT”

section.

Burner, see

“GAS PIPING”

section.

Grate, see “GRATE

INSTALLATION” section.

W415-1101 / D / 08.28.18

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

INSTALLATION OVERVIEW 2

INTRODUCTION 3

DIMENSIONS 4

GENERAL INSTRUCTIONS 5

 

 

 

INSTALLATION 7

 

GAS PIPING AND BURNER PLACEMENT 8

DAMPER STOP INSTALLATION 9

FINISHING 10

SAND OR GLASS MEDIA PLACEMENT 10

GRATE INSTALLATION 10

CHARCOAL LUMPS/EMBERS 10

LOG PLACEMENT 11

GL22 11

GL28 12

GL32 12

MOBILE HOME INSTALLATION 13

OPTIONAL REMOTE INSTALLATION (NOT SUPPLIED) 13

WIRING DIAGRAM 14

OPERATION 15

OPERATING AND LIGHTING INSTRUCTIONS 15

ADJUSTMENTS 16

 

 

MAINTENANCE 17

 

REPLACEMENTS 18

TROUBLESHOOTING 21

WARRANTY 23

SERVICE HISTORY 24

NOTES 25

1.0 INSTALLATION OVERVIEW

W415-1101 / D / 08.28.18

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR IT’S CONTROLS CAN BE DANGEROUS

AND IS PROHIBITED.

 



 

 

 

 

 



 

• Children and adults should be alerted to the hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical

barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance

or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals

out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

 

 

 



• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to

operating the appliance.

 

 









 

 

 





 



 

• Only doors / optional fronts certiﬁ ed with the unit are to be installed on the appliance.

 



 





 





• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this

appliance and shall be installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

• Installation and repair should be done by a qualiﬁ ed service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be

required due to excessive lint from carpeting, bedding material, etc. It is imperative that control

compartments, burners and circulating air passageways of the appliance be kept clean.

2.0 INTRODUCTION

W415-1101 / D / 08.28.18

2.1 DIMENSIONS

GL22 GL28 GL32

GL22 GL28 / GL32

21 1/2”

546mm

27”

686mm

32”

813mm

11 3/8”

289mm

11 3/8”

289mm

11 3/8”

289mm

11”

270mm

10 1/2”

267mm

16 1/8”

410mm

6 11/16”

170mm

6 7/8”

175mm

W415-1101 / D / 08.28.18

2.2 GENERAL INSTRUCTIONS

Thoroughly clean the chimney, ﬂue and existing appliance

before installing the new appliance into it. Do not burn solid

fuels in any appliance that is equipped with this gas log set.

The installation of this appliance must conform with

local codes or in the absence of local codes, it must

conform to ANSI Z.223.1/NFPA 54 or the CAN/CGA B149.

The installation and the provisions for combustion and

ventilation air must conform with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or the CSA B149.1, Natural

Gas and Propane Installation Code. The installation of

appliances designed for manufactured home (U.S. only) or mobile home installation must conform with the

Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI/

NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard.

Do not operate appliance in the presence of gasoline or other ﬂammable liquids and vapours. Keep area

clear of other combustible materials. The appliance and its shut off must be disconnected from the gas

supply piping system before any pressure testing of the system is done.

Installation practices vary from region to region and it is important to know the speciﬁcs that apply to your

area,

For example: in Massachusetts State:

• This product must be installed by a licensed plumber or gas ﬁtter when installed within the

commonwealth of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an

appliance insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂexible connector must not be longer than 36” (914.4mm).

• The appliance is not approved for installation in a bedroom or bathroom unless the appliance is a

direct vent sealed combustion product.

• A carbon monoxide detector is required in all rooms containing gas ﬁred appliances.

No external electricity (110 volts or 24 volts) is required for the gas system operation.

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,

WITH THE GLASS DOOR OPENED OR REMOVED.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUATE VENTILATION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE

FRONT FACE OF THE UNIT.

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT

WHEN THE APPLIANCE IS OPERATING.

FIRE RISK. EXPLOSION HAZARD.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE

TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG.

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.

USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING

COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

DO NOT USE A BLOWER INSERT, HEAT EXCHANGER INSERT OR ANY OTHER ACCESSORY NOT APPROVED FOR USE

WITH THIS APPLIANCE

WARNING

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

(NFI) as NFI Gas

Specialists

www.ncertied.org

W415-1101 / D / 08.28.18

WOLF STEEL LTD.

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: ANSI Z21.60-2003/CSA 2.26-2003 (R 2009), DECORATIVE APPLIANCE FOR INSTALLATION IN SOLID-FUEL BURNING

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE

OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THE

OWNER’S INFORMATION MANUAL PROVIDED WITH THIS APPLIANCE. FOR

ASSISTANCE OR ADDITIONAL INFORMATION, CONSULT A QUALIFIED INNSTALLER,

SERVICE AGENCY OR THE GAS SUPPLIER.

70,000BTU/h 80,000BTU/h 90,000BTU/h INPUT / ALIMENTATION 50,000BTU/h 65,000BTU/h 65,000BTU/h

0-4500FT (0-1370m) ALTITUDE / ÉLÉVATION 0-4500FT (0-1370m)

3.5” WATER COLUMN/D’UNE COLONNE D’EAU MANIFOLD PRESSURE / PRESSION AU COLLECTEUR 10” WATER COLUMN/D’UNE COLONNE D’EAU

4.5” WATER COLUMN/D’UNE COLONNE D’EAU MINIMUM SUPPLY PRESSURE / PRESSION D’ALIMENTATION MINIMALE 11” WATER COLUMN/D’UNE COLONNE D’EAU

7.0” WATER COLUMN/D’UNE COLONNE D’EAU MAXIMUM SUPPLY PRESSURE / PRESSION D’ALIMENTATION MAXIMALE 13” WATER COLUMN/D’UNE COLONNE D’EAU

GL22N

GL28N GL32N

GL22P

GL28P

GL32P

WARNING: DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN

CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH THE

APPLIANCE. FOR ISNTALLATION IN A SOLD-FUEL BURNING FIREPLACE ONLY.

THE FIREPLACE CHIMNEY MUST HAVE A PERMANENT VENT OPENING TO ATMOSPHERE OF NOT

LESS THAN 56.6

”

FOR GL22, 64

2”

FOR GL28, 71.4

2”

FOR GL32, OR AS DETERMINED BY THE

MANUFACTURER’S INSTALLATION INSTRUCTIONS.

FOR YOUR SAFETY: DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE

VAPOURS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

FOR MINIMUM CHIMNEY FLUE

SEE INSTRUCTION MANUAL.

POUR LES DIMENSIONS

MINIMALES DE LA CHEMINÉE,

CONSULTEZ LE MANUEL

D’INSTRUCTIONS

20”

22”

23”

20”

29”

14”

GL22

GL28

GL32

33”

AVERTISSEMENT: UNE INSTALLATION NON CONFORME, DES AJUSTEMENTS,

DES ALTÉRATIONS, UN SERVICE OU UN ENTRETIEN INADÉQUATS PEUVENT CAUSER DES

DOMMAGES MATÉRIELS OU DES BLESSURES CORPORELLES. RÉFÉREZ-VOUS AU

MANUEL D’INSTRUCTIONS FOURNI AVEC CET APPAREIL. POUR DE L’ASSISTANCE OU

POUR PLUS D’INFORMATION, CONSULTEZ UN INSTALLATEUR QUALIFIÉ, UNE AGENCE

D’ENTRETIEN OU LE FOURNISSEUR DE GAZ.

NATURAL GAS MODELS

PROPANE MODELS

AVERTISSEMENT: N’AJOUTEZ AUCUN MATÉRIAU À CET APPAREIL QUI ENTRERA EN

CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET APPAREIL PAR LE

FABRICANT.

POUR INSTALLATION DANS UN FOYER Â COMBUSTIBLE SOLIDE SEULEMENT.

LA CHEMINÉE DU FOYER DOIT POSSÉDER UN OUVERTURE D’ÉVACUATION PERMANENTE À L’AIR

EXTÉRIEUR DE NON MOINS DE 56,6

”

POUR LE GL22, DE 64

”

POUR LE GL28 ET 71.4

”

POUR LE GL32

OU SELON LES INSTRUCTIONS D’INSTALATION DU FABRICANT.

POUR VOTRE SÉCURITÉ: N’ENTREPOSEZ PAS ET N’UTILISEZ PAS D’ESSENCE OU

AUTRES LIQUIDES ET VAPEURS INFLAMMABLES À PROXIMITÉ DE CET OUT TOUT AUTRE

APPAREIL.

(WSL) (NGZ)

(NAC) (WUSA)

SERIAL NUMBER/NO. DE SERIE:

GSL

TITLE: RATING PLATE, GL22, GL28, GL32

REVISION: A: UPDATED ANSI INFO II 06.28.12

DWG#: W385-0677

DATE: 06.01.12_HW

MATERIAL: CLASS IIA-1 PERMANENT LABEL, METAL THICK-

NESS TO BE MIN. 0.012 MAX 0.025

SPECIFICATIONS: BLACK LETTERING ON ALUMINIUM. HIGH

TEMP INK CAN WITHSTAND TEMPS OF 175°F/ 79.5°C

MAX OVERALL SIZE: 8.5” X 4.75”

SERIAL NUMBERS ASCEND FROM: GSL 014912

CE RT IFIED

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE. ONTARIO L4M 0G8 CANADA

W385-0677 A

2.3 GENERAL INFORMATION

THIS APPLIANCE MUST NOT BE INSTALLED IN A BEDROOM OR BATHROOM.

WARNING

2.4 MINIMUM FIREPLACE CAVITY SIZE

Do not install the gas log

set into a cavity smaller

than that referenced in

the table.

HEIGHT REAR WIDTH DEPTH

LOG SET A B C

GL22 20”

(508mm)

23”

(584.2mm)

14”

(355.6mm)

GL28 20”

(508mm)

29”

(736.6mm)

14”

(355.6mm)

GL32 22”

(558.8mm)

33”

(838.2mm)

14”

(355.6mm)

GL22 GL28 GL32

NG LP NG LP NG LP

Altitude (FT) 0-4,500 0-4,500 0-4,500 0-4,500 0-4,500 0-4,500

Max input (BTU/HR) 70,000 50,000 80,000 65,000 90,000 65,000

Min Inlet Gas Supply Pressure 4.5“ InWc

(11.2mb)

11“ InWc

(27.4mb)

4.5“ InWc

(11.2mb)

11“ InWc

(27.4mb)

4.5“ InWc

(11.2mb)

11“ InWc

(27.4mb)

Max Inlet Gas Supply Pressure 7“ InWc

(17.4mb)

13“ InWc

(32.4mb)

7“ InWc

(17.4mb)

13“ InWc

(32.4mb)

7“ InWc

(17.4mb)

13“ InWc

(32.4mb)

Manifold Pressure (Under Flow

Conditions)

3.5“ InWc

(8.7mb)

10“ InWc

(25mb)

3.5“ InWc

(8.7mb)

10“ InWc

(25mb)

3.5“ InWc

(8.7mb)

10“ InWc

(25mb)

2.5 RATING PLATE

THE RATING PLATE IS CHAINED TO THE LEG OF THE VALVE CASE AND SHOULD BE TUCKED UNDER

SAMPLE

This rating plate illustration is for reference only. Refer to the rating plate on the appliance for accurate

information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

W415-1101 / D / 08.28.18

SIDE VIEW

BATTERY

SUPPORT

PLATE

VALVE

HOUSING

BATTERY

SUPPORT

BATTERY

CASE

HEAT SHIELD

3.0 INSTALLATION

The appliance and gas logs function as a system. If the appliance is not drafting properly and spilling into the

room (check with a match or a smoke stick), reposition the damper clamp until a positive draft is obtained

by opening the damper. If negative pressure in home prevents having a positive draft, consult an air quality

specialist.

3.1 BATTERY INSTALLATION

WARNING

THIS APPLIANCE MUST BE INSTALLED IN A SOLID-FUEL BURNING FIREPLACE WITH A WORKING

FLUE AND CONSTRUCTED OF NON-COMBUSTIBLE MATERIAL.

A. Remove the 2 screws securing the support plate to gain access to the battery case, as shown below.

B. Install the four 1.5V batteries (supplied) into the battery case.

C. Insert the assembled battery case into the battery support. Ensure that the heat insulation gasket

covers the top and left side of the battery case, as shown below

D. Reinstall the battery support plate.

W415-1101 / D / 08.28.18

BATTERY

SUPPORT PLATE

(BATTERY CASE

SECURED INSIDE)

SECURING

HOLES/SCREWS

VALVE

HOUSING

MIN. 1.5”

(38.1mm)

WARNING

DO NOT CONNECT EITHER THE WALL SWITCH, THERMOSTAT OR GAS VALVE TO ELECTRICITY (110

VOLTS).

This appliance must be isolated from the gas supply piping system by closing the individual manual shut off

valve during any pressure testing of the gas supply piping system at test pressure equal to or less than ½ psi

(3.5 kPa)

A. Centre the burner pan and valve assembly in the ﬁreplace

opening, making sure the appliance is at least 1.5” (38.1mm)

from the rear of the ﬁreplace.

B. Secure the burner to the ﬁreplace ﬂoor using the 2 screws

provided.

C. Install the gas line using piping ½” (12.7mm) in diameter or

greater to provide the full volume of gas to the appliance.

The installation of the gas line must be done to local and / or

National codes.

D. When rigid pipe is used an ANSI approved manual shut off

and a union must be installed upstream within the appliance

cavity.

E. To ensure the appliance operates reliably, install a sediment

trap upstream of the appliance within the structures of the

piping system.

F. When using propane, a regulator must be used between the

tank and the outside wall of the house to ensure the line pressure does not exceed 14”(355.6mm) w.c.

inside the house.

G. Check gas connections with a gas detection device to test for leaks in the system. Soapy water mixture

can also be used to check for leaks.

H. Once all the gas connections are tested for leaks, start the appliance. Follow the “OPERATING AND

LIGHTING INSTRUCTIONS” section to ensure the appliance is working properly before ﬁnishing.

Regulator

Union

Manual

Shut-Off

Valve

Wall

Shut-Off

Key

Sediment

Trap

Appliance

3" (76.3mm)

3.2 GAS PIPING AND BURNER PLACEMENT

W415-1101 / D / 08.28.18

3.3 DAMPER STOP INSTALLATION

The damper must be permanently locked in

position to prevent full closure and to provide a

minimum ﬂue opening. Various methods for locking

the damper may be used but may be restricted

from region to region and it is important to know

the speciﬁcs that apply to your area. For your

convenience a damper stop is provided with the

appliance and may be used where not prohibited

by state or local codes.

Use the 3” (72.6mm) adjustable bolt to adjust

the damper to the correct opening, based on the

enclosed chart.

Should the damper stop not ﬁt, or provide the required permanent opening (see “Minimum Damper Opening

Chart”), have the damper cut to provide a minimum permanent opening or install an alternate stop.

Creosote, ashes and loose paint must be cleaned from the chimney ﬂue and ﬁrebox by a qualiﬁed chimney

cleaner, before installing in a solid fuel burning appliance. Any outside air ducts and / or ash dumps in the

ﬁreplace shall be permanently closed at time of appliance installation.

If the damper stop (supplied) is not applicable the damper may be ﬁxed open by the following method:

• Drill a hole in either end of the damper.

• Using a bolt of sufﬁcient length and adjustment, with 2 nuts, secure to damper through the hole.

• Adjust to correct opening.

*CHIMNEY HEIGHT

MINIMUM DAMPER OPENING

GL22 GL28 GL32

6’ (1.8m)

56.6” (1439mm) 64” (6125.6mm) 71.4” (1813.5mm)

8’ (2.4m)

52.4” (1331mm) 59.7” (1516.8mm) 66.9” (1699.2mm)

10’ (3m)

48.2” (1224.2mm) 54.3” (1379.2mm) 60.2” (1529mm)

15’ (4.6m)

43.2” (1097.2mm) 48.8” (1239.5mm) 54.1” (1374.1mm)

20’ (6m)

39.8” (1011mm) 44.4”(1127.7mm) 49.1 (1247.1mm)

30’ (9.1m)

35.9” (911.8mm) 40.3” (1023.6mm) 44.5 (1130.3mm)

DAMPER

STOP

DAMPER

DAMPER STOP

DAMPER

* Height is measured from the hearth to the top of the chimney.

W415-1101 / D / 08.28.18

4.0 FINISHING

A. Either sand for natural gas models (GL22N, GL28N, GL32N) or glass for propane models (GL22P,

GL28P, GL32P), must be spread evenly over the burner pan with a gradual downward slope toward

the front of the burner pan.

B. Tear the ember material into small thin pieces and spread evenly on top of the media. Ember material

will only glow when exposed to direct ﬂame.

NOTE: DO NOT OVERFILL. DO NOT COVER THE PILOT WITH MEDIA OR EMBERS.

A. Sprinkle the charcoal embers around the front and sides of the burner pan, as indicated on the

diagram below.

B. Place the charcoal lumps on top of the charcoal embers at the front of the media.

NOTE: Do not block air shutter opening with charcoal embers or lumps.

BURNER PAN

GRATE

BURNER PAN

GRATE

TOP VIEW

GL22 FRONT VIEW

HEAT SHIELD

BURNER PAN

AIR SHUTTER

(PROPANE

MODELS ONLY)

GRATE

GL 28 / GL32 TOP VIEW

CHARCOAL

EMBERS

CHARCOAL

LUMPS

GLOWING

EMBERS

4.1 GRATE INSTALLATION

4.2 SAND OR GLASS MEDIA PLACEMENT

4.3 CHARCOAL LUMPS/EMBERS

A. For the best ﬂame performance and least carbon, position the grate as far back as possible.

B. Secure the heat shield to the back of the burner pan with the 2 supplied screws (for GL22 model

only), see Figure 1.

C. Secure the grate to the burner pan (GL28/GL32 models only) using one supplied screw, see Figure 2.

FIG. 1

FIG. 2

W415-1101 / D / 08.28.18

4.4 LOG PLACEMENT

Phazer

logs, exclusive to Napoleon Appliances, they provide a unique and realistic glowing effect that is

different in every installation. Failure to follow these log placement instructions may increase sooting.

Log colours may vary. During the initial use of the appliance, the colours will become more uniform as colour

pigments burn in during the heat activated curing process.

Positioning the logs improperly will increase ﬂame impingement and carboning.

Blocked burner ports can cause an incorrect ﬂame pattern, carbon deposits and delayed ignition. Use only

certiﬁed Phazer

logs available from your authorized dealer/distributor.

THE SUPPLIED LOG SETS ARE REVERSIBLE!

This feature allows you the option of displaying two different log styles in one log set.

WARNING

FAILURE TO POSITION THE LOGS IN ACCORDANCE WITH THESE DIAGRAMS OR FAILURE TO USE

ONLY LOGS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT MODIFY THE

PROPER LOG POSITIONS, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY AND DELAYED

IGNITION MAY OCCUR.

THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE.

76.1A

4.4.1 GL22

Place the rear log (#1) onto the 2

pins ensure the log is pushed ﬂush

against the burner support, to the

rear of the unit, as shown.

Place log (#2) onto the grate on the

left side as shown.

Place log (#3) onto the grate on the

right side as shown. Place the pins

into log (#1) as shown.

PINS

Place log (#4) onto the left side pin

as shown.

Place log (#5) onto the right side

pin as shown.

Place log (#6) onto log (#1) and

allow it to rest on log (#2).

W415-1101 / D / 08.28.18

4.4.2 GL28

4.4.3 GL32

Place log (#2) onto the grate as

shown.

Place log (#3) onto the grate as

shown. Place one pin into centre

of log (#1).

Place log (#4) onto the pin. Place log (#5) onto rear log and

let it rest on log (#2). Place a sec-

ond pin into log (#1) as shown.

Place log (#6) onto the pin as

shown. Place the remaining pin

into log (#1) as shown.

Place the rear log (#1) onto the

2 pins on the grate as shown.

Place log (#7) onto the pin as shown.

Place log (#4) onto the pin. Place log(#5) as shown and allow

it rest on the top of the previously

placed logs. Place one pin onto the

right side of the largest log as shown.

Place log (#6) onto the pin.

Place log (#1) onto the two pins

and ensure the log is pushed ﬂush

against the burner support, to the

rear of the unit, as shown.

Place log (#2) directly onto the grate

and ensure it is pulled to the front left

side of the grate.

Place log (#3) onto the grate and

ensure it is pulled to the front

right side. Ensure the two logs are

centered onto the grate. Insert one

pin into the hole of the back log as

W415-1101 / D / 08.28.18

A. Place the remote receiver to the front right corner of the ﬁreplace ﬂoor.

B. Disconnect the wires connected to ON/OFF switch.

C. Connect those wires to the remote receiver.

D. Cover the remote receiver with the log provided.

(Please refer to the remote kit leaﬂet for installation instructions.)

4.5 MOBILE HOME INSTALLATION

4.6 OPTIONAL REMOTE INSTALLATION (NOT SUPPLIED)

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home

Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas

indicated on the rating plate.

29.1B

This Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit. Built

in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base.

Use #10 hex head screws, inserted through the holes in the base to secure. For free standing products contact

your local authorized dealer / distributor for the appropriate securing kit. For mobile home installations,

the appliance must be fastened in place. It is recommended that the appliance be secured in all installations.

Always turn off the pilot and the fuel supply at the source, prior to moving the mobile home. After moving the

mobile home and prior to lighting the appliance, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (LP).

To convert from one gas to another consult your Authorized dealer/distributor.

W415-1101 / D / 08.28.18

5.0 WIRING DIAGRAM

69.9

WARNING

DO NOT WIRE 110 VOLTS TO THE VALVE OR WALL SWITCH.

ON / OFF

SWITCH

BATTERY

HOLDER

GROUND

DFC

VALVE

ORANGE

GREEN

GROUND

EYELET

ON / OFF

IPI BOARD

ELECTRONIC

VALVE







W415-1101 / D / 08.28.18

FOR YOUR SAFETY READ BEFORE LIGHTING:

• Do not turn on if children or other at risk individuals are near the appliance.

• Before operating smell all around the appliance area for gas and next to the ﬂ oor because some gas

is heavier than air and will settle on the ﬂoor.

• Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand,

do not try to repair it. Call a qualiﬁed service technician. Force or attempted repair may result in a ﬁre

or explosion.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service

technician to inspect the appliance and replace any part of the control system and any gas control

which has been underwater.

WHAT TO DO IF YOU SMELL GAS:

• Turn off all gas to the appliance.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier,

call the ﬁ re department.

LIGHTING INSTRUCTIONS:

Stop! Read the above safety information on this label.

Open the glass door if equipped.

Remove the batteries.

This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to

light the pilot by hand.

Turn manual shutoff valve clockwise to off. Located behind the appliance.

Wait ﬁ ve (5) minutes to clear out any gas. If you smell gas including near the

ﬂ oor,

STOP! Follow “B” in the above safety information on this label. If you

don’t smell gas go to the next step.

Turn manual shutoff valve counter-clockwise to on.

Replace the batteries.

Turn switch on and listen for ignition sound.

Remove the batteries.

Turn manual shutoff valve clockwise to off. Do not force.

TO TURN OFF GAS:

47.20

MANUAL SHUT-OFF

(SHOWN IN OFF POSITION)

PILOT SCREW

WARNING

IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

6.1 OPERATING AND LIGHTING INSTRUCTIONS

If the ﬁreplace is equipped with decorative glass doors, they must be fully opened when operating this gas

log set. Keep burner and control compartment clean.

6.0 OPERATION

W415-1101 / D / 08.28.18

Adjust the pilot screw to provide properly sized ﬂ ame. Turn in a

clockwise direction to reduce the gas ﬂ ow.

Check Pressure Readings:

Inlet pressure can be checked by turning screw (A) counter-

clockwise 2 or 3 turns and then placing pressure gauge tubing

over the test point. Gauge should read as described on the chart

below. Check pressure with main burner operating on “HI”.

Outlet pressure can be checked the same as above using

screw (B). Gauge should read as described on the chart

below. Check pressure with main burner operating on “HI”.

AFTER TAKING PRESSURE READINGS, BE SURE TO

TURN SCREWS CLOCKWISE FIRMLY TO RESEAL. DO

NOT OVERTORQUE.

Leak test with a soap and water solution.

Prior to pilot adjustment, ensure that the pilot assembly

has not been painted. If overspray or painting of the pilot

assembly has occurred remove the paint from the pilot

assembly, or replace. Fine emery

cloth or a synthetic scrub pad (such as

Scotch-Brite

™)

can be used to remove

the paint from the pilot hood, electrode

and ﬂ ame sensor.

*Maximum inlet pressure

not to exceeed 13”.

39.1E

PILOT SCREW

3/8” - 1/2”

(9,5mm - 12,7mm)

FLAME MUST ENVELOP

UPPER 3/8” (9.5mm) TO 1/2”

(12.7mm) OF FLAME SENSOR

PILOT

BURNER

ELECTRODE

FLAME

SENSOR

LA FLAMME DOIT

ENVELOPPER LA PARTIE

SUPÉRIEURE DE LA SONDE

DE FLAMME DE 3/8” (9,5mm)

À 1/2” (12,7mm)

ÉLECTRODE

LA SONDE

DE FLAMME

VEILLEUSE

3/8” - 1/2”

(9.5mm - 12.7mm)

Pressure

Inlet

Outlet

Natural Gas

(inches)

Natural Gas

(millibars)

Propane

(inches)

Propane

(millibars)

(MIN. 4.5")

3.5"

13"

(MIN. 11")

10"

17.4mb

(MIN. 11.2mb)

8.7mb

32.4mb

(MIN. 27.4mb)

24.9mb

It is important to periodically perform a visual check of the pilot and burner ﬂ ames. Compare them to the

illustration provided. If any ﬂ ames appear abnormal, call a service person.

3/8” - 1/2”

(9,5mm - 12,7mm)

FLAME MUST ENVELOP

UPPER 3/8” (9.5mm) TO 1/2”

(12.7mm) OF FLAME SENSOR

PILOT

BURNER

ELECTRODE

FLAME

SENSOR

LA FLAMME DOIT

ENVELOPPER LA PARTIE

SUPÉRIEURE DE LA SONDE

DE FLAMME DE 3/8” (9,5mm)

À 1/2” (12,7mm)

ÉLECTRODE

LA SONDE

DE FLAMME

VEILLEUSE

3/8” - 1/2”

(9.5mm - 12.7mm)

54.1B

7.0 ADJUSTMENTS

7.1 PILOT BURNER ADJUSTMENT

7.2 FLAME CHARACTERISTICS

NOTE: FLAME WILL VARY DEPENDING ON THE POSITION OF THE LOGS AND THE GRATE.

W415-1101 / D / 08.28.18

CAUTION:









1. 



2. 



3. 

are not burning properly.

4. 



5. 



6. 





7. 



8. 

40.19A

TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE.

APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED.

DO NOT USE ABRASIVE CLEANERS.

DO NOT PAINT THE PILOT ASSEMBLY.

MAINTENANCE

WARNING

BATTERY

SUPPORT

PLATE

BATTERY

SUPPORT

BATTERY

SUPPORT

PLATE

A. Prior to replacing the battery, turn off the gas manual shut-off valve.

B. Remove the 4 screws from the battery support plate, as shown.

C. Remove the battery case from the battery support and remove

the 4 (1.5 V) ‘AA’ size batteries from the battery case and replace

them with the new set of 4 (1.5 V) ‘AA’ size batteries.

E. Place the battery case back into the battery support.

F. Ensure when installing the battery case that the heat insullation

remains secured to the case.

G. Re-install the battery support plate and secure it using the

2 screws, as shown.

H. Turn the gas shut-off valve back to the on position.

8.0 MAINTENANCE

WARNING: Turn the manual shut-off valve to the OFF

position when changing the battery, as shown above.

MANUAL SHUT-OFF

(SHOWN IN OFF POSITION)

8.1 BATTERY REPLACEMENT

W415-1101 / D / 08.28.18

COMPONENTS

REF NO. PART NO. DESCRIPTION

1 GL-681 LOG SET GL22

2 GL-682 LOG SET, GL28

3 GL-683 LOG SET GL32

4 W010-2808 PILOT ASSEMBLY (LP 2-WAY)

5 W010-2763 PILOT ASSEMBLY (NG 2-WAY)

6 W010-2832 GRATE ASSEMBLY (GL32)

7 W010-3101 BURNER PAN ASSEMBLY (GL22)

7 W010-3102 BURNER PAN ASSEMBLY (GL28)

7 W010-3103 BURNER PAN ASSEMBLY (GL32)

8 W010-2851 DAMPER STOP ASSEMBLY (GL22/28/32)

9* W190-0072 CONTROL, IPI IGNITION BOARD

10* W445-0038 CONNECTOR 3/8 TUBE TO 3/8 PIPE

11 W660-0009 ON/OFF SWITCH

12* W725-0066 SIT VALVE 880 LP FIXED REG (LDH45)

13* W750-0175 10” (254mm) WIRE WITH 1/4” (6.4mm) FLAGS (2) (EP36)

14* W750-0214 WIRE, 19” (304.8mm) GROUND

15* W750-0269 WIRE HARNESS, WHVF29

16* W175-0227 CONNECTOR, FLEX (3/8” ST.ST.) / (9.5mm ST.ST.)

17* W255-0038 FITTING, ORIFICE 1/2” - 3/8” FP-MP / 12.7mm - 9.5mm FP-MP, GL28P/GL32P

17* W255-0042 FITTING, ORIFICE 1/2” - 3/8” FP-MP / 12.7mm - 9.5mm FP-MP, GL22N

17* W255-0041 FITTING, ORIFICE 1/2” - 3/8” FP-MP / 12.7mm - 9.5mm FP-MP, GL28N

17* W255-0040 FITTING, ORIFICE 1/2” - 3/8” FP-MP / 12.7mm - 9.5mm FP-MP, GL32N

17* W255-0036 FITTING, ORIFICE 1/2” - 3/8” FP-MP / 12.7mm - 9.5mm FP-MP, GL22P

18* W725-0065 VALVE, NG FIXED REG (LHD45)

41.1C

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts

can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE

REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

•

Model & Serial Number of appliance

•

Installation date of appliance

•

Part number

•

Description of part

•

Finish

PARTS, PART NUMBERS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PARTS IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN 2 TO 5 BUSINESS DAYS FOR MOST

DELIVERY DESTINATIONS.

PARTS NOT IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN A 2 TO 4 WEEK PERIOD, FOR

MOST CASES.

PARTS IDENTIFIED AS ‘SO’ ARE SPECIAL ORDER AND CAN TAKE UP TO 90 DAYS FOR DELIVERY.

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE

ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

** THIS IS A FAST ACTING THERMOCOUPLE. IT IS AN INTEGRAL SAFETY COMPONENT. REPLACE ONLY WITH

A FAST ACTING THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD.

WARNING

9.0 REPLACEMENTS

W415-1101 / D / 08.28.18

ACCESSORIES

REF NO. GAS LOGS DESCRIPTION

41* GD-660 REMOTE WALL SWITCH W/20’ WIRE

42* F45 ON/OFF REMOTE

19 W135-0507 LOG, TOP LEFT (GL22)

20 W135-0508 LOG, TOP CENTER (GL22)

21 W135-0509 LOG, TOP RIGHT (GL22)

22 W135-0510 LOG, REAR (GL22)

23 W135-0511 LOG, FRONT RIGHT (GL22)

24 W135-0512 LOG, FRONT LEFT (GL22)

25 W135-0513 LOG, TOP LEFT (GL28)

26 W135-0514 LOG, TOP CENTER (GL28)

27 W135-0515 LOG, TOP RIGHT (GL28)

28 W135-0516 LOG, REAR (GL28)

29 W135-0517 LOG, FRONT RIGHT (GL28)

30 W135-0518 LOG, FRONT LEFT (GL28)

31 W135-0519 LOG, TOP LEFT (GL32)

32 W135-0520 CENTER #1 (GL32)

33 W135-0521 CENTER #2 (GL32)

34 W135-0522 LOG, TOP RIGHT (GL32)

35 W135-0523 REAR #1 (GL32)

36 W135-0525 LOG, FRONT RIGHT (GL32)

37 W135-0526 LOG, FRONT LEFT (GL32)

38* W020-0718 SAND (GL22)

39* W020-0721 SAND (GL28)

40* W020-0715 SAND (GL32)

W415-1101 / D / 08.28.18

La page charge ...

NAPOLEON GL22N Manuel utilisateur

Marque: NAPOLEON

Modèle: GL22N

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON GL22N User manual

NAPOLEON GL22N Manuel utilisateur

Ce manuel convient également à

NAPOLEON GL22N Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents