American Hearth Outdoor Linear Fireplace 60 (OLL60FP/SP) Le manuel du propriétaire

Marque: American Hearth

Modèle: Outdoor Linear Fireplace 60 (OLL60FP/SP)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

WARNING

If not installed, operated and maintained in

accordance with the manufacturer's instruc-

tions, this product could expose you to sub-

stances in fuel or from fuel combustion which

can cause death or serious illness.

WARNING

If the information in these instructions are

not followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

Installation and service must be performed

by a qualied installer, service agency or

the gas supplier.

OUTDOOR LINEAR

GAS FIREPLACE

MODELS

OLL60FP12S(N,P)-1

OLL60SP12S(N,P)-1

GAS-FIRED

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide

which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space

such as a camper, tent, car or home.

WARNING

For Outdoor Use Only.

WARNING

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ame.

3. If odor continues, keep away from the

appliance and immediately call your gas

supplier or re department.

WARNING

Improper installation, adjustment, altera-

tion, service or maintenance can cause

injury or property damage. Read the instal-

lation, operating and maintenance instruc-

tions thoroughly before installing or servic-

ing this equipment.

WARNING

Do not store or use gasoline or other am-

mable vapors and liquids in the vicinity of

this or any other appliance.

An propane-cylinder not connected for use

shall not be stored in the vicinity of this or

any other appliance.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Page 1

35008-12-0519Page 2

BEFORE YOU START

1. Read the safety information on pages 4 to 5.

2. What to consider before installing. See Page 11.

3. Water drainage is required. See page 12. Optional drain tray

available.

4. Where are you going to install the unit? See pages 11 to 13.

5. Frame the opening. See pages 8 to 10 and 14 to 15.

6. Installthereplace.Seepages14to16.

7. Connect the electricity. See pages 16 and 26.

8. Connect the gas. See page 17 to 19.

9. Install the crushed glass. See page 22.

10. Lightthereplaceandtroubleshoot.Seepages23and28.

11. Showthehomeownerhowtooperatethereplace.See

page 25.

12. Show the homeowner how to do the basic maintenance. See

page 27.

Tools Needed:

(1) - 1/8-inch Allen Wrench

(2) - Adjustalbe wrenches with range of 1-inch for gas connection

(2) - Adjustable pipe wrenches

(1) - Phillips Screwdriver

CARTON CONTENTS

INDEX

NO.

DESCRIPTION

QUANTITY

SUPPLIED

OLL60FP OLL60SP

1 Glass Panel 1 2

2 Non-Combustible Panel - Top 1 2

3 Non-Combustible Panel - Side 2 4

4 Envelope 1 1

5 Nailing Flange 4 8

6 Receptacle 1 1

7 Cover Plate 1 1

8 Conduit Connector 1/2-in. 1 1

9 AA Battery 1 1

10 Burner Service Support 2 2

See Parts Lists on pages 30 to 33 for ordering replacement parts.

Do not order batteries, bolts, screws, washers or nuts. They are

standard hardware items and can be purchased at any local

hardware store.

HARDWARE PACK CONTENTS

1-1/4” PHILLIPS SELF-DRILLING SCREW

(

)

6 - OLL60FP12S(N,P))

(12 - OLL60SP12S(N,P)

#10-32 X ½”

AINLESS HEX HEAD SCREW

(8 - OLL60FP12S(N,P))

(16 - OLL60SP12S(N,P))

35008-12-0519 Page 3

TABLE OF CONTENTS

Before You Start ...........................................................................................................................2

Table Of Contents ........................................................................................................................3

Important Safety Information ......................................................................................................4

Safety Information For Users Of Propane Gas .........................................................................5

Introduction ..................................................................................................................................6

Specications ...............................................................................................................................7

Accessories ..................................................................................................................................7

Combustible Materials .................................................................................................................8

Clearances .............................................................................................................................. 8 - 9

Fireplace Dimensions ................................................................................................................10

Planning Installation ...........................................................................................................11 - 13

Fireplace Installation .....................................................................................................................

- Framing & Installation ...................................................................................................... 14 - 15

- Electrical Supply ......................................................................................................................16

- Gas Supply ..............................................................................................................................17

- Propane Gas Cylinder Information .................................................................................. 18 - 19

- Finishing .......................................................................................................................... 20 - 22

Lighting Instructions .................................................................................................................23

Main Burner Flame Characteristics ..........................................................................................24

Operation Instructions / Flame Appearance ............................................................................ 25

Wiring ..........................................................................................................................................26

Maintenance ...............................................................................................................................27

Troubleshooting .........................................................................................................................28

Master Parts Distributor List .....................................................................................................29

How To Order Repair Parts .......................................................................................................29

OLL60FP Parts List ....................................................................................................................30

OLL60FP Parts View ..................................................................................................................31

OLL60SP Parts List ....................................................................................................................32

OLL60SP Parts View ..................................................................................................................33

Fireplace Service History ..........................................................................................................34

Warranty Terms ..........................................................................................................................35

SECTION PAGE

35008-12-0519Page 4

IMPORTANT SAFETY INFORMATION

DANGER: Indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

WARNING: Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

CAUTION: Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

NOTICE: Addresses practices not related to personal injury.

WARNING

Do not place debris, logs, or other articles in replace during

operation.

WARNING

Any modication to controls can be dangerous. Improper

installation or use of the gas log set can cause serious injury or

death from re, burns, explosion or carbon monoxide poisoning.

WARNING

Make a periodic visual check of burners. Clean and replace

damaged parts.

DANGER

Children and adults should be alerted to the hazard of high

surface temperature and should stay away to avoid burns or

clothing ignition.

DANGER

Young children should be carefully supervised when they are

in the same area with the replace.

DANGER

Clothing or other ammable materials should not be hung from

the replace, or placed on or near the replace.

DANGER

Keep the replace area clear and free from combustible

material, gasoline and other ammable vapors and liquids.

• Installer: Please leave these instructions with the owner for

future reference

• This unit complies with ANSI Z21.97/CSA 2.41 for Outdoor

Gas Fireplaces.

• Installation and repair should be done by a QUALIFIED SERVICE

PERSON. This replace should be inspected before use and at

least annually by a professional service person. More frequent

cleaning may be required due to insects, pollen build up, dust,

etc. It is imperative that the control compartments, burners,

and circulating air passageways of the replace be kept clean.

• During manufacturing, fabricating and shipping, various

components of this replace are treated with certain oils,

lms or bonding agents. These agents are not harmful, but

may produce annoying smoke and smells as they are burned

off during initial operation of the replace. This is a normal

temporary occurrence.

• Follow all local codes regarding installation, combustion

and ventilation air or in the absence of local codes follow the

National Fuel Gas Code ANSI Z223.1 (US installation), or CAN/

CGA-B149, installation Code (Canada installation).

• Inspect the burner at least once a year.

• Keep burner and control compartment clean.

• DO NOT use this replace if any part has been under water.

Immediately call a qualied service technician to inspect

the replace and to replace any part of the control system

and any gas control which has been under water.

• Any guard or other protective device removed for servicing

the appliance must be replaced prior to operating the

appliance.

35008-12-0519 Page 5

SAFETY INFORMATION FOR USERS OF PROPANE GAS

Propane is a ammable gas which can cause res and explo-

sions. In its natural state, propane is odorless and colorless.

You may not know all the following safety precautions which

can protect both you and your family from an accident. Read

them carefully now, then review them point by point with the

members of your household. Someday when there may not

be a minute to lose, everyone’s safety will depend on knowing

exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas

because of the odorant put in the Propane Gas.

That's your signal to go into immediate action!

• Donotoperateelectricswitches,lightmatches,useyourphone.

Do not do anything that could ignite the gas.

• Geteveryoneoutofthebuilding,vehicle,trailer,orarea.Do

that IMMEDIATELY.

• Closeallgastankorcylindersupplyvalves.

• PropaneGasisheavierthanairandmaysettleinlowareas

such as basements. When you have reason to suspect a gas

leak,keepoutofbasementsandotherlowareas.Stayoutuntil

reghtersdeclarethemtobesafe.

• Useyourneighbor’sphoneandcallatrainedPropaneGas

servicepersonandtheredepartment.Eventhoughyoumay

not continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, lettheservicemanandreghterscheckforescaped

gas. Have them air out the area before you return. Properly

trainedPropane Gasservicepeopleshouldrepairtheleak,

thencheckandrelightthegasreplaceforyou.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell

the odor of the chemical put into the gas. You must nd out if

you can smell the odorant in propane.Smokingcandecrease

your ability to smell. Being around an odor for a time can affect your

sensitivity or ability to detect that odor. Sometimes other odors in

theareamaskthegasodor.Peoplemaynotsmellthegasodoror

theirmindsareonsomethingelse.Thinkingaboutsmellingagas

odorcanmakeiteasiertosmell.

The odorant in Propane Gas is colorless, and it can fade under

some circumstances. For example, if there is an underground

leak,themovementofthegasthroughsoilcanltertheodorant.

Odorants in Propane Gas also are subject to oxidation. This fading

canoccurifthereisrustinsidethestoragetankorinirongaspipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

takesomeoftheodorantoutofthegas,reducingitsodorintensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest gas

odor.Ifyoudetectanyodor,treatitasaseriousleak.Immediately

go into action as instructed earlier.

SOME POINTS TO REMEMBER

• LearntorecognizetheodorofPropaneGas.YourlocalPropane

GasDealercangiveyoua“ScratchandSniff”pamphlet.Use

ittondoutwhatthepropaneodorsmellslike.Ifyoususpect

thatyourPropaneGashasaweakorabnormalodor,callyour

Propane Gas Dealer.

• Ifyouarenotqualied,donotlightpilotlights,performservice,

ormakeadjustmentstoreplacesonthePropaneGassystem.

Ifyouarequalied,consciouslythinkabouttheodorofPropane

Gas prior to and while lighting pilot lights or performing service

ormakingadjustments.

• Sometimesabasementor a closed-uphousehas a musty

smell that can cover up the Propane Gas odor. Do not try to

lightpilotlights,performservice,ormakeadjustmentsinan

area where the conditions are such that you may not detect

theodoriftherehasbeenaleakofPropaneGas.

• Odorfade,duetooxidationbyrustoradsorptiononwallsof

newcylindersandtanks,ispossible.Therefore,peopleshould

beparticularlyalertandcarefulwhennewtanksorcylinders

areplacedinservice.Odorfadecanoccurinnewtanks,or

reinstalledoldtanks,iftheyarelledandallowedtosettoo

longbeforerelling.Cylindersandtankswhichhavebeenout

of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question

about the gas odor, call your Propane Gas Dealer. A peri-

odic sniff test of the Propane Gas is a good safety measure

under any condition.

• If,atanytime,youdonotsmellthePropaneGasodorantand

youthinkyoushould,assumeyouhavealeak.Thentakethe

same immediate action recommended above for the occasion

when you do detect the odorized Propane Gas.

• Ifyouexperienceacomplete“gasout,”(thecontainerisunder

novaporpressure),turnthetankvalveoffimmediately.Ifthe

container valve is left on, the container may draw in some air

throughopeningssuchaspilotlightorices.Ifthisoccurs,some

new internal rusting could occur. If the valve is left open, then

treatthecontainerasanewtank.Alwaysbesureyourcon-

tainer is under vapor pressure by turning it off at the container

beforeitgoescompletelyemptyorhavingitrelledbeforeitis

completely empty.

35008-12-0519Page 6

PRODUCT SPECIFICATIONS

DECORATIVE CRUSHED GLASS

Required Decorative Crushed Glass Media Kits (10 Sq. Ft. Required for Burner and LED Lighting)

Model Description

DG1CLF* Clear Frost

DECORATIVE CRUSHED GLASS (FOR ACCENT ONLY)

Model Description

DG1BKP* BlackPolished

DG1BUC* Blue Clear

*Clear Frost Decorative Crushed Glass is required. Decorative Glass Droplets cannot be substituted for crushed glass. One bag

of crushed glass covers 1 sq. ft. Enough crushed glass to cover 10 sq. ft. is required. Glass colors may be mixed. The maximum

amount of Crushed Decorative Glass allowed is 10 bags. Transparent and Translucent crushed glass will allow LEDs to better shine

through.

DECORATIVE GLASS DROPS & DROPLETS (MAY BE USED IN ADDITION TO CRUSHED GLASS AS AN ENHANCEMENT)

Model Description

DG1NXS 1-in. Decorative Glass Drops - Onyx Solid

DG1RYC 1-in. Decorative Glass Drops - Ruby Clear

DG1TZC 1-in. Decorative Glass Drops - Topaz Clear

DG1AB 1/2-in. Decorative Glass Droplets - Aqua Blue

DG1GC 1/2-in. Decorative Glass Droplets -Glacier Ice

DG1SL 1/2-in. Decorative Glass Droplets -Sangria Luster

Note: Decorative Glass Droplets may be added on top of the crushed glass as an enhancement. Decorative Glass Droplets must not

beplacedintheburnerame.SeeCrushedGlassInstallation,Page22.DonotaddmorethanonebagofDecorativeglassdroplets.

ACCESSORIES

Model Description

DT48LSS StainlessSteelDrainTray-(Fits48and60-in.replaces)

WD60LSS StainlessSteelWeatherDoor-60-in(ordertwoforsee-throughreplaces)

WG60LT1 DeectorGlassforWindyApplications-60-in(ordertwoforsee-throughreplaces)

35829 Natural to Propane Conversion Kit

35830 Propane to Natural Conversion Kit

ACCESSORIES

Model Number OLL60FP12 (Natural) OLL60FP12 (Propane) OLL60SP)12 (Natural) OLL60SP12 (Propane)

InputBTU/HrMaximum 65,000 65,000 65,000 65,000

InputBTU/HrMinimum 39,000 37,000 39,000 37,000

KWH Maximum 19.05 19.05 19.05 19.05

KWH Minimum 11.43 10.84 11.43 10.84

Orice #14 #41 #14 #41

Air Shutter Setting 1/16" Open Full Open 1/16" Open Full Open

Gas Inlet Shut-Off Valve Pipe

1/2 NPT 1/2 NPT 1/2 NPT 1/2 NPT

GAS SUPPLY PRESSURES (INCHES WATER COLUMN)

Gas Type Maximum Minimum Manifold

Natural 14 4.5 3.5

Propane 14 10.8 10

35008-12-0519 Page 7

INTRODUCTION

Hearthsshouldslopeawayfromthefrontofthereplaceandchase

at 1/8 in. to 1/4 in. per foot. Metal safety strips must be on top of

any combustible hearth materials used for moisture management.

Whenpurchasingareboxorreplacewerecommendyoualso

buy a weather cover to protect the unit from moisture. Never install

a burner where moisture cannot drain off easily. We recommend a

weather barrier to protect the burner from moisture.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performedonlybyaqualiedagency.Theterm"qualiedagency"

meansanyindividual,rm,corporationorcompanywhicheitherin

person or through a representative is engaged in and is responsible for

(a) the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

suchwork,familiarwithallprecautionsrequiredandhascomplied

with all the requirements of the authority having jurisdiction.

Local Codes

• Whenthereplaceisconnectedtoaxedpipingsystem,the

installation must conform with local codes, or in the ab-

sence of local codes with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or International Fuel Gas Code.

• Wheninstalled,thereplacemustbeelectricallygrounded

in accordance with local codes, or in the absence of local

codes with the National Electrical Code, ANSI/NFPA 70, if

applicable.

Commonwealth of Massachusetts: The installation must be

madebyalicensedplumberorgastterintheCommonwealth

of Massachusetts.

The installation must conform with local codes or, in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1.*

*Available from the American National Standards Institute, Inc. 1430

Broadway, New York, N.Y. 10018.

High Altitudes

For altitudes/elevations above 2,000 feet (610m), ratings should be

reduced at the rate of 4 percent for each 1,000 feet (305m) above

sea level. Contact the manufacturer or your gas company before

changingspud/oricesize.

Well Head Gas Installations

Some natural gas utilities use "well head" gas. This may affect the

Btu output of the unit. Contact the gas company for the heating value.

Contact the manufacturer or your gas company before changing

spud/oricesize.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner fill out and mail registration

card supplied with this fireplace or register online at

www.empirecomfort.com.

3. Installer should show owner how to start and operate outdoor

replace.

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of an outdoor

gasreplace.

WARNING

To avoid injury or damage to the replace or surrounding

area, do not burn wood or other solid fuels in this replace.

WARNING

ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN

BE DANGEROUS.

Improper installation or use of the replace can cause seri-

ous injury or death from re, burns, explosion or carbon

monoxide poisoning.

Thisseriesisdesigncertiedinaccordancewith

ANSI Z21.97/CSA

2.41 for Outdoor Gas Fireplaces

and should be installed according

to these instructions.

Any alteration of the original design, installing it other than as

shown in these instructions or using a type of gas not shown

on the rating plate, is the responsibility of the person and

company making the change.

Manual Valve Safety System

When the burner ignites, a thermocouple senses a signal (electrical

current) that energizes a magnet in the gas valve. After 30 to 60

seconds,thecontrolknobcanbereleased.Ifthe thermocouple

doesnotsensetheame,thegaswillshutoff.

Important

All correspondence should refer to complete Model Number, Serial

Number and type of gas.

Moisture Resistance

Thisoutdoorreplacewillshedmoderateamountsofwater,butis

not waterproof. Water and condensing water vapor may enter the

chase under certain conditions.

Thereplacewillnotperformasanexteriorwall.Moisturepenetration

must beconsideredforconstructionthat places the replace in

structure walls or on moisture sensitive surfaces.

When installed on exterior walls: Empire Comfort Systems

recommends the replace chase be constructed outside the

structure's weather envelope. Where the platform meets the wall,

useaashing detailsimilartothatrequired forattacheddecks.

Chase platforms, including hearths should slope away from the

structureat1/4in.perfoot.Thereplacecanbeshimmedlevel.

When installed on surfaces where water may collect or cause

damage: Empire Comfort Systems recommends a slope of 1/8 to

1/4in.perfoottowardsthedrainportsuggested.Thereplacecan

be shimmed level.

35008-12-0519Page 8

CLEARANCES

Index

Letter

Description

Dimension from

Fireplace Opening

(in inches)

From ground or other

combustible surface

10-1/4*

B From Side Walls 6

C From Ceiling (minimum) 24

D Alcove Width (minimum) 72

E Alcove Depth (maximum) 24

F Ceiling Height (minimum) 90

*Note: DimensionAincludes3-1/2in.underreplaceforsupport

framing and drain tray installation.

Figure 3 - Alcove Clearances

Minimum Wall and Ceiling Clearances

SidewallClearances:Theclearancefromtheinsideofthereplace

to any combustible wall should not be less than 6 in.

Ceiling Clearances: The ceiling height should not be less than

24 in. from the top opening.

Mantel Clearances: If a combustible mantel is installed, it must meet

the clearance requirements detailed in Figure 2.

COMBUSTIBLES

ALLOWED

MANTEL

2”

4”

6”

8”

12”

16 13/16”

14 3/8”

19 3/16”

21 5/8”

24”

10”

Figure 2 - Mantel Clearances

Donotattachcombustiblematerialtothemantelofyourreplace.

Thisisarehazard.

Figure 1

COMBUSTIBLE MATERIALS

Nogreetingcards,stockingsorornamentationofanytypeshouldbe

placedonorattachedtothereplace.Thisisaheatingappliance.

Theowofheatcanignitecombustibles.

NOTE: Forsee-thrureplaces,thisappliestobothsidesofthe

unit.

Television Considerations

Installingatelevisionaboveareplacehasbecomeincreasingly

popular;however,theareaaboveanyreplacegetshotandmost

TV manufacturers recommend against placing their products near

a heat source.

Ifyouinstallatelevisionabovethisreplace,EmpireComfortSys-

tems accepts no responsibility for damage or injuries. Follow the

television manufacturer’s installation instructions, including any

recommendations regarding proximity to heat sources.

IfyouhaveaTVaboveyourreplace,turnoffthereplaceand

let it cool completely before servicing or touching any buttons on

the TV.

35008-12-0519 Page 9

Figure 4

Front and Side View of Non-Combustible Panel to Opening on Fireplace's Face

*NOTE: 8-in.minimumofnon-combustiblematerialisrequiredabovethereplaceopening.16-in.ofnon-combustiblematerialis

provided to allow for placement of wall joint in a cooler temperature zone.

NON-COMBUSTIBLE

WALL BOARD PROVIDED

Framing

Header

Fireplace

Opening

2 1/4”

Fireplace

Opening

Support

Framing

Non-Combustible

Panels installed

over Appliance Opening

Non-Combustible

Side Panel

BOTH SIDES

6 1/2

”

8” *

Fireplace Nailing

Header

CLEARANCES

35008-12-0519Page 10

FIREPLACE DIMENSIONS

INDEX

LETTER

DIMENSION DESCRIPTION

OLL60FP OLL60SP

Dimensions in Inches

A Themaximumheightofreboxface 30-7/8 30-7/8

B Themaximumwidthofthereboxface(excludingnailinganges)

63-3/4 63-3/4

C Themaximumdepthoftherebox 19-1/8 22-1/2

D Theheightofthereboxopening 16-3/16 16-3/16

E Thewidthofthereboxopening 60 60

F Theinteriordepthoftherebox(notshown)

19 23-7/8

G Therearexteriorwidthoftherebox(notshown) 60 60

K Height from the bottom of the box to the gas line opening 2-9/16 2-9/16

L Depth from the front of the box to gas line opening 5-3/16 5-3/16

M Depth from rear of box to gas line opening 5-3/16 N/A

N Glass height 3-1/2 3-1/2

O Glass width 59-3/8 59-3/8

Q Distancefromoortoreplaceopening 6-11/16 6-11/16

N/A - Not applicable for this unit.

35008-12-0519 Page 11

What to Consider Before Installing

1. Verifyreplacegastypeandgassupplytypearethesame.

2. Lookforalocationwherecombustibleswillnotinterfere.

3. 120V GFI power outlet will be needed for LED lights

4. Choose a location for gas shutoff valve.

5. Verify ventilation meets at least minimum requirements

6. Wind and rain direction

7. Drainageunderreplace.

8. Drain pan and weather door accessories.

9. Glass accessories

Whenplanningtheinstallationforthereplace,determinewherethe

unit is to be installed and whether optional accessories are desired.

Gas supply piping should also be planned at this time.

Thereplacecanbemountedonanyofthesesurfaces:

1. A raised frame of combustible material so contact is made on

allfourperimeteredgesofthebottomofthereplaceatleast

3-1/2in.abovetheoor.

2. Four corners ofthereplace so contactismade on allfour

perimeter edges on the bottom of the unit at least 3-1/2 in.

abovetheoor.Checklocalcodesforallowances.

At this point, you should have decided what components to include

inyourinstallation,andwherethereplaceistobelocated.Ifthis

has not been done, stop and consult your dealer for assistance

with this planning.

WARNING

This replace is intended for installation on an outdoor patio

or yard. This replace shall be used only outdoors in a well

ventilated space and shall NOT be used in a building, garage,

or other enclosed area. This replace cannot be installed

with an opening to the inside of a residence.

NOTICE: This fireplace is NOT equipped with an Oxygen

Depletion Sensor (ODS) pilot.

Installationofthereplace may be inan"open"area, however

it is recommended that this fireplace be installed in an area

shelteredfromdirectwinds.Directwindwillcauseanerraticame

andpossibleburneroutage.Thiserraticamecouldalsoleadto

excessiveblacksoot.Thesearenuisanceissuesratherthansafety

issues. Avoid areas where excessive moisture or running water may

benearoronreplace.

Typical installation may include covered patio, open porch, gazebo

or an outside wall of a house.

• Minimum porch area – 96 square feet

• Minimum ceiling height – 90 inches

LED Lights will require a 120V GFI power outlet on the valve side of

thereplace.TheGFIplugwillbelocatedoutsideofthereplace.

Ajunctionboxisprovidedinsidethereplacetoprovidealocation

to plug in the LEDs.

Outdoor Fireplace Enclosure Requirements

Donotinstallreplaceuntilallnecessaryprovisionsaremadefor

combustion and ventilation air. Consult the written instructions

providedwiththereplaceforinformationconcerningcombustion

and ventilation air. In the absence of instructions, refer to the

National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion

and Ventilation, or applicable local codes.

Installation in partial enclosures must conform with one of the

following conditions:

• With walls on all sides, but with no overhead cover.

See Figure 5.

FIREPLACE

Figure 5

• Within a partial enclosure which includes an overhead cover

and no more than two side walls. These side walls may be

parallel, as in a breezeway or at right angles to each side.

See Figure 6.

FIREPLACE

Figure 6

PLANNING INSTALLATION

35008-12-0519Page 12

PLANNING INSTALLATION

• Within a partial enclosure that includes an overhead cover and

three side walls, as long as 30 percent or more of the horizontal

periphery (perimeter of walls and open side) of the enclosure

is permanently open. See Figure 7.

FIREPLACE

Figure 7

If installing in a screened in porch, the open space must be adjusted

(increased) from 30 percent (adjusted open space = 30% / % open

area of the screen mesh). "Example, if you used a screen with a

66% open area, the minimum open space of your building must

be 46% of the periphery. If you have a covered screened-in porch

that has two side walls that are 16', one wall that was against the

house that's 20' and one open side that's 20', you would have a

perimeter of 72'. You would need to have 33' of the perimeter open

(72' x 46% = 33')."

(Contact your screen manufacturer or screen dealer to

determine your screens open area).

ATTENTION: Vinyl Soffit, Vinyl Ceiling, Vinyl Overhang

Disclaimer

Clearances are to heat resistant material (i.e. wood, metal). This

does not include vinyl. Empire Comfort Systems Inc. will not be

held responsible for heat damage caused from terminating under

vinyl overhangs, vinyl ceilings or vinyl ventilated/unventilated

softs.

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, personal injury

or loss of life. Installation and service must be performed

by a qualied installer, service agency or the gas supplier.

Gas Line Connection

Thereplace isdesigned toaccept a1/2 in.gas line.Have the

lineinstalledbyaqualiedservicepersoninaccordancewithall

building codes. Consult local building codes to properly size the gas

supplylineleadingtothe1/2in.hook-upattheunit.Thestateof

Massachusettsrequiresthataexiblereplaceconnectorcannot

exceed three feet in length.

Aex-lineconnectiontothevalvesisprovided.The gas shut-off

valve must be located outside of the unit in an accessible area.

Checkgastypeontheratinglabellocatedonthebackofthecontrol

door. If the gas listed on the rating label located on the control panel,

does not match your gas supply, DO NOT INSTALL. Contact your

dealerforpropermodelorconversionkit.

AlwaysuseanexternalregulatorforallPropanereplacestoreduce

thesupplytankpressuretoamaximumof13in.w.c.

WARNING

Connection directly to an unregulated Propane Tank can

cause an explosion.

WARNING

Risk of re, explosion or asphyxiation. Ensure no ignition,

ame or spark are near during installation. This includes

cigarettes or cell phones.

Leaktestallconnectionswithasoapandwatersolution.Bubble

formationwillindicatealeak.Usecautiontoavoidburns.

Figure 8

Water Drainage Requirement

Provisions must be made to drain water away from the unit. An

optional drain pan can be purchased from your Empire Dealer to

tunderthereplace.Ifinstallingtheoptionaldrainpan,itmust

beinstalledpriortoinstallingthereplace.Formoreinformation,

refer to the installation instructions supplied with the drain pan. If

this drain is not used, other water drainage is required.

35008-12-0519 Page 13

Electrical Considerations

CAUTION

All wiring should be done by a qualied electrician and

shall be in compliance with all local, city and state building

codes. Before making the electrical connection, make sure

that the main power supply is disconnected. The replace,

when installed, must be electrically grounded in accordance

with local codes, or in the absence of local codes, with the

National Electrical Code ANSI/NFPA 70 (Latest Edition).

A factory installed junction box is located on the lower right side

ofthereplace.Thejunctionboxandwiringmayberelocatedto

theoppositesideofthereplaceifdesired.Wiringtothejunction

box must be metal clad or enclosed in a conduit and must be

approved for outdoor use. Connect the wiring to an external GFI

protectedoutletinstallednearthereplace.SeeFigure9.

GFI Outlet

CONTROLS

Figure 9

PLANNING INSTALLATION

35008-12-0519Page 14

FIREPLACE FRAMING AND INSTALLATION

Unpacking the Fireplace

After removal of the plastic wrap, remove the screws holding the

cornerpostsandplywoodtothereplace.Discardthecorner

posts and plywood.

Thenon-combustibleboardisunderthereplaceonthepallet.

Removeanyprotectivelmfromreplaceandallcomponents

(nailinganges,nailingheaders,etc.).

Framing

Fireplacesupportframingshouldbebuiltbeforethereplaceisset

inplace.Thereplaceframingmaybeconstructedof2x4lumber.

Theframingheadersmustrestonthereplacenailingheaders.

Refer to Figure 11 for minimum framing dimensions.

CAUTION

Measure replace dimensions and verify framing methods,

and wall covering details before framing construction begins.

Framing dimension A includes a 16-1/2 in. clearance for nailing

headers on rebox. After installing rebox into framing, the

nished wall surface must cover the 16-1/2 in. opening above

the rebox.

KEEP OPEN

AREA FOR

DRAINAGE

WATER

DRAINAGE

THIS SIDE

FRAMING DIMENSIONS (in inches)

OLL60FP OLL60SP

Height A 31 31

Width B 64 64

Depth C 19-1/4 22-1/2

Figure 11 - Fireplace Framing

Beforecompletingtheframingandinstallingreplace,providea

pathforwaterdrainageoutofthereplace.

Determine if the optional accessory drain pan will be used. See

Page 12. If the drain pan will be installed, follow the instructions

providedwiththedrainpankittoinstallitatthispoint.

Installation

1. Choose installation location.

2. Constructthesupportframingforthereplace.Seeframing

dimensions, Figure 11. See Clearances, Pages 8 and 9.

3. Locatethenailingangesintheinstallationenvelopeand

attachthemtothesidesofthereplacewithtwo#10-32x1/2

hex screws each.

Figure 12 - Nailing Flange Position

4. Bendthenailingangetabsoutatrightanglesuntiltheyare

ushwiththefaceofthereplace.

For see-through replaces only: Bend the tabs on one

sideofthereplaceonly.Bendthetabsonthetopheaderof

the opposite face at right angles to allow the tabs to clear the

enclosureframingwhenslidingthereplaceintoposisiton.

See Figure 13.

5. Liftthereplaceandsetintotheframe.Slidethereplace

backuntilnailingangesmeettheframe.Securethere-

place to the frame with one #8x1 drywall screw each. For

see-thrureplaces,bendthebacksidenailingangesout

and right angles and secure with one #8x1 drywall screw

each.

Figure 13

FRAMING & INSTALLATION

35008-12-0519 Page 15

FIREPLACE FRAMING AND INSTALLATION

6. Secure the nailing header to the side framing studs with four

#8 x 1 drywall screws

7. To connect the gas line and install the electrical connection,

theburnerassemblymustbetiltedupwardinthereplace.

a Remove the control door by opening the door, removing

the center piovt pin, and lifting the door upward to dis-

engage the slots on the ends of the door from the pivot

pins.

b. Remove the two control door pivot bolts and washers.

See Figure 14.

Figure 14

c. Remove two screws from front corners of the control

panel with a Phillips head screw driver. See Figure 15.

Figure 15

d. Lift front of burner assembly and tilt upwards and toward

thebackofthereplace.Retrievethetwosupportsfrom

insidethereplaceandplaceoneeachsideagainstthe

front corners of the cabinet bottom and under the front

corners of the control panel.

NOTE:Usecarewhenraisingtheburnertoavoid

scratchingthestainlessinteriorofthereplace.

PROP SUPPORT

IN FOUR CORNERS

Figure 16

8. Installgasandelectricalsuppliestoreplace.Seepage17

for gas supply requirements. For ease of installation, the

gas and electrical supply are located on the valve side of the

replace.Bothmayberelocatedtoentertheoppositesideof

thereplace.

FRAMING & INSTALLATION

35008-12-0519Page 16

FIREPLACE FRAMING AND INSTALLATION

GFI Outlet

CONTROLS

Figure 17

GROUND

CONDUIT

RECEPTACLE

120 VOLT

POWER SUPPLY

OUTLET

COVER

GASKET

Figure 18

ELECTRICAL SUPPLY

CAUTION

All wiring should be done by a qualied electrician and

shall be in compliance with all local, city and state building

codes. Before making the electrical connection, make sure

that the main power supply is disconnected. The replace,

when installed, must be electrically grounded in accordance

with local codes, or in the absence of local codes, with the

National Electrical Code ANSI/NFPA 70 (Latest Edition).

Wiring to the junction box must be metal clad or enclosed in a

conduit and must be approved for outdoor use. A connector for

the junction box to accommodate 1/2-in. conduit is supplied in the

instructionenvelope.Thereplacereceptaclemustbeconnected

toanexternalGFIprotectedoutletinstallednearthereplace

See Figure 17.

Route the wiring from the external GFI outlet through the conduit

to the junction box. Leave approximately 6-in. of wire in the junc-

tion box for connection.

Retrieve the receptacle and cover from the instruction enve-

lope.Attachtheblackwiretothegoldscrewandwhitewireto

the silver screw of the receptacle. The ground wire should be

attached to the green ground screw on the junction box and the

receptacle.

Placereceptacleinpositionandattachcoverplate.Makesure

the cover plate doors open upward. Be sure to test the receptacle

to ensure the GFI circuit functions properly. Plug transformer

power cord into receptacle, and close the unused receptacle

door.

35008-12-0519 Page 17

FIREPLACE FRAMING AND INSTALLATION

• Solidfuelsshallnotbeburnedinthisreplace.

• The maximum gas inlet supply pressure is 11 in. for Propane

and 10.5 in. for Natural.

• Forreplacesforxedfuelpipingsystemandequippedwith

areplacegaspressureregulator,therequiredmanifold

pressure in inches water column: 11 in. for Propane and

4.5 in. Natural.

• Forreplacesforxedfuelpipingsystemandequippedwith

areplacegaspressureregulator,thereplaceanditsindi-

vidual shutoff valve must be disconnected from the gas sup-

ply piping system during any pressure testing of that system

attestpressuresinexcessof1/2psi(3.5kPa).

Thereplacemustbeisolatedfromthegassupplypiping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at test

pressuresequaltoorlessthan1/2psi(3.5kPa).

Checkalllocalcodesforrequirements,especiallyforthesizeand

type of gas supply line required.

RECOMMENDED MINIMUM GAS PIPE DIAMETER

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2 in.

12.7mm

3/8 in.

9.5mm

1/2 in.

12.7mm

3/8 in.

9.5mm

10-40 feet

4-12 meters

1/2 in.

12.7mm

1/2 in.

12.7mm

5/8 in.

15.9mm

1/2 in.

12.7mm

40-100 feet

13-30 meters

1/2 in.

12.7mm

1/2 in.

12.7mm

3/4 in.

19mm

1/2 in.

12.7mm

100-150 feet

31-46 meters

3/4 in.

19mm

1/2 in.

12.7mm

7/8 in.

22.2mm

3/4 in.

19mm

NOTE:Checktoconrmwhetheryourlocalcodesallowplasticor

copper tubing for outdoor use.

NOTE: Because some municipalities have additional local codes,

consult your local authority and installation code.

Installing a Manual Gas Shut-Off Valve

Eachreplacemusthaveanaccessiblemanualgasshut-offvalve

located in the vicinity of the unit. Where none exists, or where its size

or location is not adequate, contact your local authorized installer

for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

totheactionofliqueedpetroleumgases.Thegaslinesmustbe

checkedforleaksbytheinstaller.Thisshouldbedonewithasoap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made. To avoid damage to

the gas piping, removal all testing solution when testing is complete.

WARNING

Never use an exposed ame to check for leaks. Fireplace

must be disconnected from piping at inlet of control valve and

pipe capped or plugged for pressure test. Never pressure test

with replace connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required by

the National Fuel Gas Code that a drip line be installed near the

gas inlet. This should consist of a vertical length of pipe connected

intothegaslinebyateetingwithacaponthebottominwhich

condensation and foreign particles may collect.

The use of the following gas connectors is recommended:

— ANSI Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANSI Z21.45 Assembled Flexible Appliance Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction The Commonwealth of Massachusetts requires

thataexibleapplianceconnectorcannotexceedthreefeetinlength.

NATURAL

GAS SUPPLY

SHUT

-OFF

LVE

FLEX TUBING

MALE NPT to

MALE FLARE

REGULATOR

NIPPLE

NATURAL

GAS SUPPLY

MALE NPT to

MALE FLARE

LP GAS

SUPPLY

SHUT-OFF

VALVE

FLEX TUBING

MALE NPT to

MALE FLARE

VALVE

MALE NPT to

MALE FLARE

LP GAS

SUPPLY

VALVE

FEMALE NPT to

FEMALE NPT

FEMALE NPT to

FEMALE NPT

Figure 19

NOTE: Gas shut-off valve shown. Other valves approved to use

with gas allowed.

Flex tubing to valve is pre-installed at the factory. Flare connector

is located in the envelope.

An accessible manual gas shut off valve must be installed

externaltothereplace.

GAS SUPPLY

35008-12-0519Page 18

WARNING

If these instructions are not followed exactly, a re caus-

ing death or serious injury may occur.

Propane Cylinder Specications

Thisreplacecanbeusedwithanon-disposableself-contained

Propane Gas supply system:

• Propane cylinders may be acceptable for use with the

replaceprovidedtheyarecompatiblewiththereplace

retention means.

• Propane Gas supply cylinder must be constructed and

markedinaccordancewiththeU.S. Department of

Transportation (D.O.T.) Specications for Propane Gas

Cylinders, or the Standard for Cylinders, Spheres and

Tubes for Transportation of Dangerous Goods and Com-

mission, CAN/CSA-B339 as applicable.

• Propane Gas supply cylinders between 4 and 40

poundsmusthaveanoverllpreventiondevice.

• Propane Gas supply cylinder must have a connection

devicecompatiblewiththeconnectionofthereplace.

• IfthereplaceisequippedwithaCGANo.600Cylinder

Connection Device, the cylinder must be disconnected

whenthereplaceisnotinuse.

• Ifreplaceistobepermanentlyconnectedtoagaspip-

ingsystemfromaremotesupplytank,installationmust

be in accordance with local codes or, in the absence

of local codes, with the National Fuel Gas Codes ANSI

Z223.1/NFPA 54.

• A dented or rusty cylinder may be hazardous and should

becheckedbyyourpropanesupplier.Neveruseacylin-

der with a damaged valve.

• Thisreplacemaybeusedwitha20lb.(9.1kg)or30lb

(13.6kg)sizepropanecylinderonly(notsupplied).

• The propane cylinder must be provided with a shut-

off valve terminating in a propane cylinder valve type

QCC1, and a safety relief device having direct commu-

nication with the vapor space of the cylinder.

• The cylinder supply system must be arranged for vapor

withdrawal and the cylinder shall include a collar to

protect the cylinder valve.

• The Propane Gas cylinder must be provided with a

listedoverllprotectiondevice(OPD).Neverllthe

cylinder beyond 80 percent full.

• Do not store a spare Propane Gas cylinder under or

nearthisreplace.

• Useonlyapressureregulatorandhoseassemblythat

suppliesapressureof11in.watercolumntothere-

placeandhasaQCC1typetting.

• Cylinders to be used with this unit must be supplied with

a QCC1 cylinder valve. A QCC1 cylinder has a positive

seatingconnection,whichwillnotallowgasowuntila

positive seal has been achieved. It is also equipped with

anexcessowdevice.Inordertoattainfullowtothe

replace,thevalvemustbeintheoffpositionwhenthe

cylinder valve is turned on.

WARNING

A re will result if the gas supply hose makes contact with

the underside of the replace.

Propane Gas

Attachcylinderretainingbracketsuppliedtothebaseofthecyl-

inder. Then secure to the surface to which it sits. Cylinder should

be on a level surface.

Cylinder Retaining Bracket

1. Fastenthebrackettothebottomofthepropanebottleusing

bolt and nut (not supplied).

2. Tighten the lag screw into the mounting surface leaving ap-

proximately 1/4 in. of thread above the surface.

3. Slidepropanebottleintopositionsothatthebracketslides

under the head of the lag screw.

4. Tightenthelagscrewontothebracket.

5. For fastening to a concrete surface a concrete anchor will be

required. (Not supplied)

Cylinder Connection:Ensurethegasregulatorhoseiskink

free. Remove the cap or plug from the cylinder fuel valve. Insert

theblackQCC1regulatornippleontotheQCC1fuelvalve.Hand

tightenclockwise.Donotusetools.Leaktestalljointspriorto

usingthereplace.Aleaktestmustbeperformedannuallyand

eachtimeacylinderishookeduporifapartofthegassystem

isreplaced.Ifthisreplaceistobeconnecteddirectlytoahouse

propane gas supply line, follow the instructions for the natural

gashook-up.

Safety Considerations

• Makesurecylindervalveisinitsfulloffposition.(Turnclock-

wise to stop).

• Checkcylindervalvefeaturestoensureithasproperex-

ternalmatingthreads.(CylinderValveMarked:USEWITH

TYPE 1)

• Inspect hose for damage. Never attempt to use damaged or

plugged equipment. See your local Propane Gas Dealer for

repairs.

• When connecting regulator assembly to the cylinder valve,

handtightenblackQCC1nutclockwisetoapositivestop.

DONOTuseawrenchtotighten.Useofawrenchmaydam-

agethequickclosingcouplingnutandresultinahazardous

condition.

• Locate the hose out of pathways where people may trip over

it or in areas where the hose may be subject to accidental

damage.

• Opencylindervalvefully(counter-clockwise).Turntheshut

off valve at the unit slowly to the on position and use a soapy

watersolutiontocheckallconnectionsforleaksasindicated

inthediagramsbeforeattemptingtolightthereplace.Ifa

leakisfound,turntankvalveoffanddonotusethereplace

until repairs can be made.

FIREPLACE FRAMING AND INSTALLATION

PROPANE GAS CYLINDER INFORMATION

35008-12-0519 Page 19

Enclosures For Propane Gas Supply Systems

Enclosures for Propane Gas supply cylinders shall be ventilated

byopeningsatthelevelofthecylindervalveandatoorlevel.

The effectiveness of the opening(s) for purposes of ventilation

shall be determined with the Propane Gas supply cylinder(s) in

place. This shall be accomplished by one of the following.

a. One side of the enclosure shall be completely open; or

b. For an enclosure having four sides, a top and a bottom:

1. At least two ventilation openings at cylinder valve level

shall be provided in the side wall, equally sized, spaced

at 180 degrees (3.14 rad), and unobstructed. Each

opening shall have a total free area of not less than

1/2sqinperpound(2.3sq.cm/kg)ofstoredfuelcapac-

ity and not less than a total free area of 10 sq in (64.5

sq. cm).

2. Ventilationopening(s)shallbeprovidedatoorlevel

and shall have a total free area of not less than 1/2 sq in

perpound(3.2sq.cm/kg)ofstoredfuelcapacityandnot

less than a total free area of 10 sq in (64.5 sq. cm). If

ventilationopeningsatoorlevelareinasideall,there

shall be at least two openings. The bottom of the open-

ingsshallbeatoorlevelandtheupperedgenomore

than5in.(127mm)abovetheoor.Theopeningsshall

be equally sized, spaced at 180 degrees (3.14 rad) and

unobstructed.

3. Every opening shall have minimum dimensions so as to

permit the entrance of a 1/8 in. (3.2 mm) diameter rod.

4. There shall be a minimum clearance of 2 in. (51 mm)

betweenthelowersurfaceoftheoorofthePropane

Gas supply cylinder enclosure and the ground.

• Cylinder valves shall be readily accessible for hand opera-

tion. A door on the enclosure to gain access to the cylinder

valvesisacceptable,provideditisnon-lockingandcanbe

opened without the use of tools.

• Thedesignofthereplaceshallbesuchthat(1)the

Propane Gas supply cylinder(s) can be connected, discon-

nected and the connections inspected and tested outside the

cylinder enclosure; and (2) those connections which could

be disturbed when installing the cylinder(s) in the enclosure

canbeleaktestedinsidetheenclosure;

• Ventilation openings in sidewalls shall not communicate

directlywithotherenclosuresofthereplace.

The enclosure for the Propane Gas cylinder shall isolate the

cylinder from the burner compartment to provide:

a. Shielding from heat radiation;

b. Aamebarrier;and

c. Protection from foreign material.

Be certain to mount the Propane Gas cylinder on a at

surface and restrain it using a cylinder retaining bracket to

prevent it from tipping.

NON-LOCKING

DOOR

TOP AND SIDE PARTITION

TO ISOLATE TANK FROM

FIREPLACE

OPENING B

OPENING A

1” MAX

5” MAX

TOP AND SIDE PARTITION

TO ISOLATE TANK FROM

FIREPLACE

FIREPLACE POSITIONED

ABOVE TANK ENCLOSURE

FIREPLACE POSITIONED

BESIDE TANK ENCLOSURE

5” MAX

1” MAX

2” MIN

Cylinder

Size

Opening

Area A

Opening

Area B

Recommended

Dimension C

20lb

(9.1kg)

20 sq.in.

(130cm

)

10 sq.in.

(65cm

)

34 in.

(863mm)

30lb

(13.6kg)

30 sq.in.

(195cm

)

15 sq.in.

(100cm

)

34 in.

(863mm)

NOTE: There shall be a minimum clearance of 2 in. (51 mm)

betweenthelowersurfaceoftheoorofthePropaneGassupply

cylinder enclosure and the ground.

Figure 20

FIREPLACE FRAMING AND INSTALLATION

PROPANE GAS CYLINDER INFORMATION

35008-12-0519Page 20

FIREPLACE FRAMING AND INSTALLATION

FINISHING

1. Aftergasandelectricalhookupiscompleted,lowerand

secure the burner assembly (leave two supports in bottom of

replaceforfutureuse)withthetwoscrewsremovedinStep

7 on page 15.

2. Installtheglasswindpanel(twousedonsee-throughre-

places). See Figure 21.

Figure 21

3. Reinstall the pivot bolts and washers removed in step 7 on

page 15 and reinstall the control door and center pivot pin.

4. UnscrewtheignitorbuttonandinstalltheAAbatteryprovided

in the instruction envelope prior to closing the control door. See

Figure 22.

Figure 22

Framing and Finishing

Thereplaceisinstalledwithpanelsaroundtheopeningasa

clean face installation. See Figure 23. The top and sides must

use non-combustible panels (provided) where shown going over

thefaceofthereplace.Outsideofthisarea,anyweatherproof

wallboard may be used.

NON-COMBUSTIBLE

WALL BOARD

(PROVIDED)

FINISHED

WEATHERPROOF

MATERIAL

Figure 23

La page charge ...

American Hearth Outdoor Linear Fireplace 60 (OLL60FP/SP) Le manuel du propriétaire

Marque: American Hearth

Modèle: Outdoor Linear Fireplace 60 (OLL60FP/SP)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: American Hearth Outdoor Linear Fireplace 60 (OLL60FP/SP) Owner's manual

American Hearth Outdoor Linear Fireplace 60 (OLL60FP/SP) Le manuel du propriétaire

American Hearth Outdoor Linear Fireplace 60 (OLL60FP/SP) Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents