American Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

Marque: American Hearth

Modèle: Outdoor Linear Fireplace 48 (OLL48FP/SP)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

OLL48FP/SP

OUTDOOR LINEAR

GAS FIREPLACE

MODELS:

OLL48FP12S(N,P)

OLL48SP12S(N,P)

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING

For Outdoor Use Only.

WARNING

If the information in these instructions are

not followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

WARNING

If not installed, operated and maintained in

accordance with the manufacturer's instructions,

this product could expose you to substances in

fuel or from fuel combustion which can cause

death or serious illness.

Installation and service must be performed

by a qualied installer, service agency or the

gas supplier.

DANGER

FIRE OR EXPLOSION HAZARD

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ame.

3. If odor continues, leave the area

immediately.

4. After leaving the area, call your gas

supplier or re department.

Failure to follow these instructions could

result in re or explosion, which could cause

property damage, personal injury, or death.

WARNING

Improper installation, adjustment, alteration,

service or maintenance can cause injury or

property damage. Read the installation, operating

and maintenance instructions thoroughly before

installing or servicing this equipment.

WARNING

Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any

other appliance.

An Propane-cylinder not connected for use

shall not be stored in the vicinity of this or any

other appliance.

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide

which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space

such as a camper, tent, car or home.

GAS-FIRED

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Page 1

41308-2-0620Page 2

PROPANE GAS CYLINDER INFORMATION

DANGER - FLAMMABLE GAS UNDER PRESSURE.

LEAKING LP-GAS MAY CAUSE A FIRE OR EXPLOSION IF IGNITED

CAUSING SERIOUS BODILY INJURY OR DEATH.

CONTACT LP GAS SUPPLIER FOR REPAIRS, OR DISPOSAL OF THIS

CYLINDER OR UNUSED PROPANE-GAS.

WARNING - FOR OUTDOOR USE ONLY.*

DO NOT USE OR STORE CYLINDER IN A BUILDING,

GARAGE OR ENCLOSED AREA.

WARNING:

• Know the odor of propane gas. If you hear, see

or smell leaking propane gas, immediately get

everyone away from the cylinder and call the

Fire Department. Do not attempt repairs.

• Caution your propane gas supplier to:

- Be certain cylinder is purged of trapped

 airpriortorstlling.

- Becertainnottooverllthecylinder.

- Becertaincylinderrequalicationdateis

checked.

• Propane gas is heavier than air and may settle

in low places while dissipating.

• Contact with the liquid contents of cylinder

will cause freeze burns to the skin.

• Do not allow children to tamper or play with

cylinder.

• When not connected for use, keep cylinder

valve turned off. Self contained appliances

shall be limited to a cylinder of 30 lb

capacity or less.

• Do not use, store or transport cylinder where

it would be exposed to high temperatures.

Relief valve may open allowing a large

amountofammablegastoescape.

• When transporting, keep cylinder secured in an

upright position with cylinder valve turned off.

WHEN CONNECTING FOR USE:

• Use only in compliance with applicable codes.

• Read and follow manufacturer’s instructions.

• Consult manufacturer’s instructions

concerning the cylinder connection provided

with your appliance.

• Be sure regulator vent is not pointing up.

• Turn off all valves on the appliance.

• Do not check for gas leaks with a match or

opename.Applysoapywateratareasmarked

“X”. Open cylinder valve. If bubble appears,

close valve and have propane gas service

personmakeneededrepairs.Also,check

appliance valves and connections to make sure

they do not leak before lighting appliance.

• Light appliance(s) following manufacturer’s

instructions.

• When appliance is not in use, keep the

cylinder valve closed.

DO NOT REMOVE, DEFACE, OR OBLITERATE THIS LABEL

*EXCEPT AS AUTHORIZED BY ANSI/NFPA 58.

DANGER.

Do not store a spare propane cylinder under or near a barbecue grill, or other heat sources.

NEVERllanpropanecylinderbeyond80%full:arecausingdeathorseriousinjurymayoccur.

Cylinder valve

hand wheel

Point of

connection

Liquid level

indicator

(optional)

relief valve

Pressure

Cylinder

41308-2-0620 Page 3

BEFORE YOU START

1. Read the safety information on pages 5, 33 and 34.

2. What to consider before installing. See Page 10.

Water drainage is required. See page 11. Optional drain

tray available.

4. Where are you going to install the unit? See pages 10 to 11.

5. Frame the opening. See pages 7-9 and 13.

6. Installthereplace.Seepages13to15.

7. Connect the electricity. See pages 16 and 25.

8. Connectthegas.Seepage17to19.

9. Install the crushed glass. See page 21.

10. Lightthereplaceandtroubleshoot.Seepages22and27.

11. Showthehomeownerhowtooperatethereplace.See

page 24.

12.

Show the homeowner how to do the basic maintenance.

See page 26.

CARTON CONTENTS

Index

Number

Description

Quantity

Supplied

OLL48FP OLL48SP

1 Glass Panel 1 2

Non-Combustible Panel - Top

2 4

Non-Combustible Panel - Side

2 4

4 Envelope 1 1

5 Nailing Flange 4 8

6 Top Mounting 3 6

7 Receptacle 1 1

8 Cover Plate 1 1

9 Conduit Connector 1/2-in. 1 1

10 AABattery 1 1

11 Burner Service Support 2 2

See Parts Lists on pages 29 to 32 for ordering replacement parts.

Do not order batteries, bolts, screws, washers or nuts. They are

standard hardware items and can be purchased at any local

hardware store.

HARDWARE PACK CONTENTS

1-1/4” PHILLIPS DRYWALL SCREW (20)

#10-32 X ½” STAINLESS HEX HEAD SCREW (16)

#10-32X1/2"STAINLESSHEXHEADSCREW

14-OLL48FP12S(N,P)

28-OLL48SP12S(N,P)

1-1/4"PHILLIPSDRYWALLSCREW

33-OLL48FP12S(N,P)

66-OLL48SP12S(N,P)

1-1/4” PHILLIPS DRYWALL SCREW (20)

#10-32 X ½” STAINLESS HEX HEAD SCREW (16)

41308-2-0620Page 4

TABLE OF CONTENTS

Propane Gas Cylinder Information ................................................................................................ 2

BeforeYouStart ............................................................................................................................3

Table of Contents ..........................................................................................................................4

Introduction....................................................................................................................................5

Specications ................................................................................................................................6

Accessories ................................................................................................................................... 6

Combustible Materials ...................................................................................................................7

Clearances ...............................................................................................................................7-8

Fireplace Dimensions ....................................................................................................................9

Planning Installation .............................................................................................................10 - 12

Fireplace Framing and Installation .......................................................................................13 - 21

Lighting Instructions ....................................................................................................................22

Main Burner Flame Characteristics ............................................................................................. 23

OperationInstructions/FlameAppearance .................................................................................. 24

Wiring ..........................................................................................................................................25

Maintenance ................................................................................................................................26

Troubleshooting ...........................................................................................................................27

Master Parts Distributor List ........................................................................................................ 28

HowToOrderRepairParts .........................................................................................................28

OLL48FP12SPartsList...............................................................................................................29

OLL48FP12SPartsView ............................................................................................................30

OLL48SP12SPartsList ..............................................................................................................31

OLL48SP12SPartsView ............................................................................................................32

Important Safety Information ....................................................................................................... 33

Safety Information for Users of Propane Gas .............................................................................34

Warranty Terms ...........................................................................................................................35

SECTION PAGE

41308-2-0620 Page 5

INTRODUCTION

When installed on exterior walls: Empire Comfort Systems

recommends the replace chase be constructed outside the

structure's weather envelope. Where the platform meets the wall,

useaashingdetailsimilartothatrequiredforattacheddecks.

Chase platforms, including hearths should slope away from the

structureat1/4in.perfoot.Thereplacecanbeshimmedlevel.

When installed on surfaces where water may collect or cause

damage:EmpireComfortSystemsrecommendsaslopeof1/8to

1/4in.perfoottowardsthedrainportsuggested.Thereplacecan

be shimmed level.

Hearthsshouldslopeawayfromthefrontofthereplaceandchase

at1/8in.to1/4in.perfoot.Metalsafetystripsmustbeontopof

any combustible hearth materials used for moisture management.

Whenpurchasingareboxorreplacewerecommendyoualso

buy a weather cover to protect the unit from moisture. Never install

a burner where moisture cannot drain off easily. We recommend a

weather barrier to protect the burner from moisture.

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performedonlybyaqualiedagency.Theterm"qualiedagency"

meansanyindividual,rm,corporationorcompanywhicheitherin

person or through a representative is engaged in and is responsible for

(a) the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

such work, familiar with all precautions required and has complied

withalltherequirementsoftheauthorityhavingjurisdiction.

Local Codes

• Whenthereplaceisconnectedtoaxedpipingsystem,the

installation must conform with local codes, or in the ab-

sence of local codes with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, or International Fuel Gas Code.

• Wheninstalled,thereplacemustbeelectricallygrounded

in accordance with local codes, or in the absence of local

codes with the National Electrical Code, ANSI/NFPA 70, if

applicable.

Commonwealth of Massachusetts: The installation must be

madebyalicensedplumberorgastterintheCommonwealth

of Massachusetts.

The installation must conform with local codes or, in the absence

oflocalcodes,withtheNationalFuelGasCode,ANSIZ223.1.*

*Available from the American National Standards Institute, Inc. 1430

Broadway, New York, N.Y. 10018.

High Altitudes

For altitudes/elevations above 2,000 feet (610m), ratings should be

reduced at the rate of 4 percent for each 1,000 feet (305m) above

sea level. Contact the manufacturer or your gas company before

changingspud/oricesize.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner fill out and mail registration

card supplied with this fireplace or register online at

www.empirecomfort.com.

3. Installer should show owner how to start and operate outdoor

replace.

AlwaysconsultyourlocalBuildingDepartmentregardingregulations,

codes or ordinances which apply to the installation of an outdoor

gasreplace.

*Aftermarket: Completionofsale,notforpurposeofresale,from

the manufacturer.

Well Head Gas Installations

Some natural gas utilities use "well head" gas. This may affect the

Btu output of the unit. Contact the gas company for the heating value.

Contact the manufacturer or your gas company before changing

spud/oricesize.

WARNING

This replace is not for use with solid fuels.

WARNING

ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS CAN

BE DANGEROUS.

Improper installation or use of the replace can cause seri-

ous injury or death from re, burns, explosion or carbon

monoxide poisoning.

Thisseriesisdesigncertiedinaccordancewith

ANSI Z21.97/CSA

2.41 for Outdoor Gas Fireplaces

and should be installed according

to these instructions.

Any alteration of the original design, installing it other than as

shown in these instructions or using a type of gas not shown

on the rating plate, is the responsibility of the person and

company making the change.

Manual Valve Safety System

When the burner ignites, a thermocouple senses a signal (electrical

current)thatenergizesamagnetinthegasvalve.After30to60

seconds, the control knob can be released. If the thermocouple

doesnotsensetheame,thegaswillshutoff.

Important

AllcorrespondenceshouldrefertocompleteModelNumber,Serial

Number and type of gas.

Moisture Resistance

Thisoutdoorreplacewillshedmoderateamountsofwater,butis

not waterproof. Water and condensing water vapor may enter the

chase under certain conditions.

Thereplacewillnotperformasanexteriorwall.Moisturepenetration

must be consideredfor construction that places thereplace in

structure walls or on moisture sensitive surfaces.

41308-2-0620Page 6

SPECIFICATIONS

DECORATIVE CRUSHED GLASS

Required Decorative Crushed Glass Media Kits (8 Sq. Ft. Required for Burner and LED Lighting)

Model Description

DG1CLF* Clear Frost

Decorative Crushed Glass (For Accent Only)

Model Description

DG1BKP* Black Polished

DG1BUC* Blue Clear

*ClearFrostDecorativeCrushedGlassisrequired.DecorativeGlassDropletscannotbesubstitutedforcrushedglass.Onebagof

crushedglasscovers1sq.ft.Enoughcrushedglasstocover8sq.ft.isrequired.Glasscolorsmaybemixed.Themaximumamount

ofCrushedDecorativeGlassallowedis8bags.TransparentandTranslucentcrushedglasswillallowLEDstobettershinethrough.

DECORATIVE GLASS DROPS 1-IN. (MAY BE USED IN ADDITION TO CRUSHED GLASS)

Model Description

DG1NXS Onyx Solid

DG1RYC Ruby Clear

DG1TZC Topaz Clear

DECORATIVE GLASS DROPLETS 1/2-IN. (MAY BE USED IN ADDITION TO CRUSHED GLASS)

Model Description

DG1AB AquaBlue

DG1GC Glacier Ice

DG1SL Sangria Luster

Note: Decorative Glass Droplets may be added on top of the crushed glass as an enhancement. Decorative Glass Droplets must not

beplacedintheburnerame.SeeCrushedGlassInstallation,Page20.DonotaddmorethanonebagofDecorativeglassdroplets.

ACCESSORIES

Model Description

DT48LSS StainlessSteelDrainTray-48-in

WD48LSS StainlessSteelWeatherDoor-48-in(ordertwoforsee-throughreplaces)

WG48LT1 DeectorGlassforWindyApplications-48-in(ordertwoforsee-throughreplaces)

33815 Natural to Propane Conversion Kit

33814 Propane to Natural Conversion Kit

ACCESSORIES

Model Number OLL48FP (Natural) OLL48FP (Propane) OLL48SP (Natural) OLL48SP (Propane)

InputBTU/HrMaximum 55,000 55,000 55,000 55,000

InputBTU/HrMinimum 35,000 35,000 35,000 35,000

KWHMaximum 16.12 16.12 16.12 16.12

KWHMinimum 10.26 10.26 10.26 10.26

Orice #24 #44 #24 #44

AirShutterSetting 1/16" Open 3/8"Open 1/16" Open 3/8"Open

Gas Inlet Shut-Off Valve Pipe

1/2 NPT 1/2 NPT 1/2 NPT 1/2 NPT

GAS SUPPLY PRESSURES (INCHES WATER COLUMN)

Gas Type Maximum Minimum Manifold

Natural 14 4.5 4.5

Propane 14 11 11

41308-2-0620 Page 7

CLEARANCES

Index

Letter

Description

Dimension from

Fireplace Opening

(in inches)

From ground or other

non-combustible surface

10-1/4*

B From Side Walls 6

C From Ceiling 24

D AlcoveWidth(minimum) 60

E AlcoveDepth(maximum) 24

*NOTE: DimensionAincludes3-1/2in.underreplacefor

support framing and drain tray installation.

Figure 3 - Alcove Clearances

Minimum Wall and Ceiling Clearances

SidewallClearances:Theclearancefromtheinsideofthereplace

to any combustible wall should not be less than 6 in.

Ceiling Clearances: The ceiling height should not be less than

24 in. from the top opening.

Mantel Clearances: If a combustible mantel is installed, it must meet

the clearance requirements detailed in Figure 2.

Figure 2 - Mantel Clearances

Donotattachcombustiblematerialtothemantelofyourreplace.

Thisisarehazard.

Figure 1

COMBUSTIBLE MATERIALS

No greeting cards, stockings or ornamentation of any type should be

placedonorattachedtothereplace.Thisisaheatingappliance.

Theowofheatcanignitecombustibles.

NOTE: Forsee-thrureplaces,thisappliestobothsidesofthe

unit.

Television Considerations

Installingatelevisionaboveareplacehasbecomeincreasingly

popular;however,theareaaboveanyreplacegetshotandmost

TV manufacturers recommend against placing their products near

a heat source.

Ifyouinstallatelevisionabovethisreplace,EmpireComfortSys-

temsacceptsnoresponsibilityfordamageorinjuries.Followthe

television manufacturer’s installation instructions, including any

recommendations regarding proximity to heat sources.

IfyouhaveaTVaboveyourreplace,turnoffthereplaceand

let it cool completely before servicing or touching any buttons on

the TV.

41308-2-0620Page8

Figure 4

Front and Side View of Non-Combustible Panel to Opening on Fireplace's Face

NOTE: Recommendedinstallationifusing6in.orsmallertilesornishingmaterials.

CLEARANCES

Figure 5

Front View and Side Prole of Non-Combustible Panel to Top of Fireplace

NOTE: Recommendedinstallationifusing6-in.orlargertilesornishingmaterials.

Note for Figures 4 and 5:Ifinstallingthewallboardintheushfaceconguration,trimthetwotoppanelsto16-1/2in.x26-3/4in.The

smaller non-combustible panels will not be needed.

41308-2-0620 Page 9

FIREPLACE DIMENSIONS

INDEX

LETTER

DIMENSION DESCRIPTION

OLL48FP OLL48SP

Dimensions in Inches

A Themaximumheightofreboxface(excludingstandoffs) 24-5/16 24-5/16

B Themaximumwidthofthereboxface(excludingnailinganges) 51-3/4 51-3/4

C Themaximumdepthoftherebox 19-1/16 22-5/16

D Theheightofthereboxopening 16-3/16 16-3/16

E Thewidthofthereboxopening 48 48

F Theinteriordepthoftherebox(notshown)

19 22-9/32

G Therearexteriorwidthoftherebox(notshown) 51-3/4 51-3/4

H Theheighttothereboxstandoffs 16-1/2 16-1/2

I Width from the left side of the box to the centerline of vent N/A N/A

J Depth from back of box to centerline of top vent N/A N/A

K Heightfromthebottomoftheboxtothegaslineopening 2-9/16 2-9/16

L Depth from the front of the box to gas line opening 5-3/16 5-3/16

M Depth from rear of box to gas line opening 13-21/32 N/A

N Glass height 3-1/2 3-1/2

O Glass width 47-3/8 47-3/8

P Depth from front of box to centerline of vent N/A N/A

Q Distancefromoortoreplaceopening 6-11/16 6-11/16

R Heightfromoortoventcollar N/A N/A

S Overall height to header 40-13/16 40-13/16

N/A-Notapplicableforthisunit.

41308-2-0620Page 10

What to Consider Before Installing

1. Verifyreplacegastypeandgassupplytypearethesame.

2. Look for a location where combustibles will not interfere.

3. 120V GFI power outlet will be needed for LED lights

4. Choose a location for gas shutoff valve.

5. Verify ventilation meets at least minimum requirements

6. Wind and rain direction

7. Drainageunderreplace.

8. Considerationdrainpanandweatherdooraccessories.

9. Glass accessories

Inplanning the installationfor the replace,it is necessary to

determine where the unit is to be installed and whether optional

accessories are desired. Gas supply piping should also be planned

at this time.

Thereplacecanbemountedonanyofthesesurfaces:

1. Araisedframeofcombustiblematerialsocontactismadeon

allfourperimeteredgesofthebottomofthereplaceatleast

3-1/2in.abovetheoor.

2. Fourcorners of the replacesocontact is made onallfour

perimeter edges on the bottom of the unit at least 3-1/2 in.

abovetheoor.Checklocalcodesforallowances.

Atthispoint,youshouldhavedecidedwhatcomponentstoinclude

inyourinstallation,andwherethereplaceistobelocated.Ifthis

has not been done, stop and consult your dealer for assistance

with this planning.

WARNING

This replace is intended for installation on an outdoor patio

or yard. This replace shall be used only outdoors in a well

ventilated space and shall NOT be used in a building, garage,

or other enclosed area. This replace cannot be installed

with an opening to the inside of a residence.

NOTICE: This fireplace is NOT equipped with an Oxygen

Depletion Sensor (ODS) pilot.

Itisrecommendedthatthisreplacebeinstalledina“sheltered”

area.Direct wind willcause an erratic ame and possible main

burneroutage.  This erraticame could alsolead to excessive

black soot. These issues are nuisance issues rather than a safety

issues.Avoidareaswhereexcessivemoistureorrunningwatermay

benearoronreplace.

Typical installation may include covered patio, open porch, gazebo

or an outside wall of a house.

• Minimum porch area – 96 square feet

• Minimum ceiling height – 90 inches

LED Lights will require a 120V GFI power outlet on the valve side of

thereplace.TheGFIplugwillbelocatedoutsideofthereplace.

Ajunctionboxisprovidedinsidethereplacetoprovidealocation

to plug in the LEDs.

Outdoor Fireplace Enclosure Requirements

Donotinstallreplaceuntilallnecessaryprovisionsaremadefor

combustion and ventilation air. Consult the written instructions

providedwiththereplaceforinformationconcerningcombustion

and ventilation air. In the absence of instructions, refer to the

NationalFuelGasCode,ANSIZ223.1/NFPA54,AirforCombustion

and Ventilation, or applicable local codes.

Installation must conform with one of the following conditions:

• With walls on all sides, but with no overhead cover.

See Figure 6.

Figure 6

• Within a partial enclosure which includes an overhead cover

and no more than two side walls. These side walls may be

parallel, as in a breezeway or at right angles to each side.

See Figure 7.

Figure 7

PLANNING INSTALLATION

41308-2-0620 Page 11

PLANNING INSTALLATION (CONT'D)

• Within a partial enclosure that includes an overhead cover and

three side walls, as long as 30 percent or more of the horizontal

periphery (perimeter of walls and open side) of the enclosure

is permanently open. See Figure 8.

Figure 8

Ifinstallinginascreenedinporch,theopenspacemustbeadjusted

(increased)from30percent(adjustedopenspace=30%/%open

area of the screen mesh). "Example, if you used a screen with a

66%openarea,theminimumopenspaceofyourbuildingmust

be46%oftheperiphery.Ifyouhaveacoveredscreened-inporch

that has two side walls that are 16', one wall that was against the

house that's 20' and one open side that's 20', you would have a

perimeterof72'.Youwouldneedtohave33'oftheperimeteropen

(72'x46%=33')."

(Contact your screen manufacturer or screen dealer to

determine your screens open area).

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, personal injury

or loss of life. Installation and service must be performed

by a qualied installer, service agency or the gas supplier.

Gas Line Connection

Thereplaceisdesignedtoaccepta1/2in.gasline.Havetheline

installedbyaqualiedservicepersoninaccordancewithallbuilding

codes. Consult local building codes to properly size the gas supply

line leading to the 1/2 in. hook-up at the unit. The Commonwealth

ofMassachusettsrequiresthataexiblereplaceconnectorcannot

exceed three feet in length.

Aex-lineconnectiontothevalveshashavebeenprovided.The

gas shut-off valve must be located outside of the unit in an

accessible area.

Check gas type on the rating label located on the back of the control

door. If the gas listed on the rating label located on the control pane,

doesnotmatchyourgassupply,DONOTINSTALL.Contactyour

dealer for proper model or conversion kit.

AlwaysuseanexternalregulatorforallPropanereplacestoreduce

the supply tank pressure to a maximum of 13 in. w.c.

WARNING

Connection directly to an unregulated propane tank can

cause an explosion.

WARNING

Risk of re, explosion or asphyxiation. Ensure no ignition

ame or spark are near during installation. This includes

cigarettes or cell phones.

Leak test all connections with a soap and water solution. Bubble

formation will indicate a leak. Use caution to avoid burns.

Figure 9

Water Drainage Requirement*

Provisionsmustbemadetodrainwaterawayfrom theunit.An

optional drain pan can be purchased from your Empire Dealer to

tunderthereplace.Ifinstallingtheoptionaldrainpan,itmust

beinstalledpriortoinstallingthereplace.Formoreinformation,

refer to the installation instructions supplied with the drain pan. If

this drain is not used, other water drainage is required.

*Ifinstallingadraintrayaccessory,addatleast6inchesmoreto

the height of the enclosure to allow enough space for the drain

pan, connector, and tubing clearance.

41308-2-0620Page 12

Electrical Considerations

CAUTION

All wiring should be done by a qualied electrician and

shall be in compliance with all local, city and state building

codes. Before making the electrical connection, make sure

that the main power supply is disconnected. The replace,

when installed, must be electrically grounded in accordance

with local codes, or in the absence of local codes, with the

National Electrical Code ANSI/NFPA 70 (Latest Edition).

Afactoryinstalledjunctionboxislocatedonthelowerrightside

ofthereplace.Thejunctionboxandwiringmayberelocatedto

theoppositesideofthereplaceifdesired.Wiringtothejunction

box must be metal clad or enclosed in a conduit and must be

approved for outdoor use. Connect the wiring to an external GFI

protectedoutletinstallednearthereplace.See Figure 10.

Figure 10

PLANNING INSTALLATION (CONT'D)

41308-2-0620 Page 13

FIREPLACE FRAMING AND INSTALLATION

Unpacking the Fireplace

Afterremovalofthecardboardcarton,removethebandhold-

ing the corner posts, non-combustible board and top mounting

standoffstothereplace.Setthenon-combustibleboardandtop

mounting standoffs aside, discard the corner posts.

Toremovethereplacefromthepallet,removeanddiscardthe

blackclipsandscrewsfasteningeachendofthereplacetothe

pallet.

Removeanyprotectivelmfromreplaceandallcomponents

(nailinganges,standoffs,etc.).

Figure 11

Framing

Fireplacesupportframingshouldbebuiltbeforethereplaceisset

inplace.Thereplaceframingmaybeconstructedof2x4lumber.

Theframingheadersmustrestonthereplacestandoffs.Referto

Figure 12 for minimum framing dimensions.

CAUTION

Measure replace dimensions and verify framing methods,

and wall covering details before framing construction begins.

Framing dimension A includes a 16-1/2 in. clearance for

standoffs on rebox. After installing rebox into framing, the

nished wall surface must cover the 16-1/2 in. opening above

the rebox.

KEEP OPEN

AREA FOR

DRAINAGE

INSTALL AFTER INSTALLATION

OF FIREPLACE IF DRAIN TRAY

IS USED

WATER

DRAINAGE

THIS SIDE

FRAMING DIMENSIONS (in inches)

OLL48FP OLL48SP

Height A 40-13/16 40-13/16

Width B 52 52

Depth C 19-1/16 22-5/16

Figure 12 - Fireplace Framing

Beforecompletingtheframingandinstallingreplace,providea

pathforwaterdrainageoutofthereplace.

Determine if the optional accessory drain pan will be used. See

Page 13. If the drain pan will be installed, follow the instructions

provided with the drain pan kit to install it at this point.

Installation

1. Choose installation location.

2. Constructthesupportframingforthereplace.Seeframing

dimensions, Figure 12. See Clearances, Pages 6 and 7.

3. Locatethenailingangesintheinstallationenvelopeand

attachthemtothesidesofthereplacewithtwo#10-32x1/2

hexscrewseach.Theangeshavethreepositionsto

accommodate the wall board being installed over the face of

theunit(cleanface)orushwiththefaceoftheunitwith

1/2in.or5/8in.thickwallboard.See Figure 13.

Figure 13

4. Bendthenailingangetabsoutatrightangles.Forsee-

throughreplacesonlybendthetabsononesideofthe

replacetoallowthetabsontheothersidetoclearthe

enclosure framing.

5. Liftthereplaceandsetintotheframe.Slidethereplace

backuntilnailingangesmeettheframe.Securethere-

placetotheframewithone#8x1drywallscreweach.For

see-thrureplaces,bendthebacksidenailingangesout

andrightanglesandsecurewithone#8x1drywallscrew

each.

Figure 14

FRAMING & INSTALLATION

41308-2-0620Page 14

FIREPLACE FRAMING AND INSTALLATION (CONT'D)

6. Locatethetopstandoffs(threeforsingle-sidedreplaces

andsixforsee-throughreplaces).Bendmountingfeetand

attachtothetopofthereplacewithtwo#10-32x1/2hex

screws each.

Figure 15

The standoffs may be installed in one of three positions to

accommodate installing the wall board over the front of the

replace(cleanface)orushwiththereplacewith1/2in.or

5/8in.thickwallboard.

See Figure 16.

Figure 16

7. Secure the top of the standoffs to the header.

8. Toconnectthegaslineandinstalltheelectricalconnection,

theburnerassemblymustbetiltedupwardinthereplace.

To lift the burner assembly, remove the control door by open-

ing the door and lifting it upward to disengage the slots on

the door from the pivot pins.. Remove the two control door

pivot bolts and washers. See Figure 17.

Figure 17

9. Remove two screws from front corners of the control panel

with a Phillips head screw driver. See Figure 18.

Figure 18

FRAMING & INSTALLATION

41308-2-0620 Page 15

FIREPLACE FRAMING AND INSTALLATION (CONT'D)

FRAMING & INSTALLATION

10. Lift front of burner assembly and tilt upwards and toward the

backofthereplace.Retrievethetwosupportsfrominside

thereplaceandplaceoneeachsideagainstthefrontcor-

ners of the cabinet bottom and under the front corners of the

control panel.

PROP SUPPORT

IN FOUR CORNERS

Figure 19

11. Installgasandelectricalsuppliestoreplace.Seepage16

for gas supply requirements. For ease of installation, the

gas and electrical supply are located on the valve side of the

replace.Bothmayberelocatedtoentertheoppositesideof

thereplace.

41308-2-0620Page 16

FIREPLACE FRAMING AND INSTALLATION (CONT'D)

Figure 20

GROUND

CONDUIT

RECEPTACLE

120 VOLT

POWER SUPPLY

OUTLET

COVER

GASKET

Figure 21

ELECTRICAL SUPPLY

CAUTION

All wiring should be done by a qualied electrician and

shall be in compliance with all local, city and state building

codes. Before making the electrical connection, make sure

that the main power supply is disconnected. The replace,

when installed, must be electrically grounded in accordance

with local codes, or in the absence of local codes, with the

National Electrical Code ANSI/NFPA 70 (Latest Edition).

Wiringtothejunctionboxmustbemetalcladorenclosedina

conduitandmustbeapprovedforoutdooruse.Aconnectorfor

thejunctionboxtoaccommodate1/2-in.conduitissuppliedinthe

instructionenvelope.Thereplacereceptaclemustbeconnected

toanexternalGFIprotectedoutletinstallednearthereplace

See Figure 20.

Route the wiring from the external GFI outlet through the conduit

tothejunctionbox.Leaveapproximately6-in.ofwireinthejunc-

tion box for connection.

Retrieve the receptacle and cover from the instruction enve-

lope.Attachtheblackwireandwhitewiretothereceptacle.The

ground wire should be attached to the green (ground screw on

thejunctionboxandthereceptacle.

Place receptacle in position and attach cover plate. Make sure

the cover plate doors open upward. Be sure to test the receptacle

to ensure the GFI circuit functions properly. Plug transformer

power cord into receptacle, and close the unused receptacle

door.

41308-2-0620 Page 17

FIREPLACE FRAMING AND INSTALLATION (CONT'D)

• Solidfuelsshallnotbeburnedinthisreplace.

• The maximum gas inlet supply pressure is 11 in. for Propane

and 10.5 in. for Natural.

• Forreplacesforxedfuelpipingsystemandequippedwith

areplacegaspressureregulator,therequiredmanifold

pressure in inches water column: 11 in. for Propane and

4.5 in. Natural.

• Forreplacesforxedfuelpipingsystemandequippedwith

areplacegaspressureregulator,thereplaceanditsindi-

vidual shutoff valve must be disconnected from the gas sup-

ply piping system during any pressure testing of that system

at test pressures in excess of 1/2 psi (3.5 kPa).

Thereplacemustbeisolatedfromthegassupplypiping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

Check all local codes for requirements, especially for the size and

type of gas supply line required.

RECOMMENDED MINIMUM GAS PIPE DIAMETER

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2 in.

12.7mm

3/8in.

9.5mm

1/2 in.

12.7mm

3/8in.

9.5mm

10-40 feet

4-12 meters

1/2 in.

12.7mm

1/2 in.

12.7mm

5/8in.

15.9mm

1/2 in.

12.7mm

40-100 feet

13-30 meters

1/2 in.

12.7mm

1/2 in.

12.7mm

3/4 in.

19mm

1/2 in.

12.7mm

100-150 feet

31-46 meters

3/4 in.

19mm

1/2 in.

12.7mm

7/8in.

22.2mm

3/4 in.

19mm

NOTE:Neveruseplasticpipe.Checktoconrmwhetheryourlocal

codes allow copper tubing.

NOTE: Because some municipalities have additional local codes,

consult your local authority and installation code.

Installing a Manual Gas Shut-Off

Eachreplacemusthaveanaccessiblemanualgasshut-offlocated

in the vicinity of the unit. Where none exists, or where its size or

location is not adequate, contact your local authorized installer for

installation or relocation.

Compoundsusedonthreadedjointsofgaspipingshallberesistant

totheactionofliqueedpetroleumgases.Thegaslinesmustbe

checked for leaks by the installer. This should be done with a soap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.

Never use an exposed ame to check for leaks. Fireplace must

be disconnected from piping at inlet of control valve and pipe

capped or plugged for pressure test. Never pressure test with

replace connected; control valve will sustain damage!

Agasvalveandgroundjointunionshouldbeinstalledinthegas

line upstream of the gas control to aid in servicing. It is required by

the National Fuel Gas Code that a drip line be installed near the gas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

The use of the following gas connectors is recommended:

— ANSIZ21.24ApplianceConnectorsofCorrugatedMetalTubing

and Fittings

— ANSI Z21.45 Assembled Flexible Appliance Connectors of

OtherThanAll-MetalConstruction

The above connectors may be used if acceptable by the authority

havingjurisdictionTheCommonwealthofMassachusettsrequires

thataexibleapplianceconnectorcannotexceedthreefeetinlength.

NATURAL

GAS SUPPLY

SHUT

-OFF

LVE

FLEX TUBING

MALE NPT to

MALE FLARE

REGULATOR

NIPPLE

NATURAL

GAS SUPPLY

MALE NPT to

MALE FLARE

LP GAS

SUPPLY

SHUT-OFF

VALVE

FLEX TUBING

MALE NPT to

MALE FLARE

VALVE

MALE NPT to

MALE FLARE

LP GAS

SUPPLY

VALVE

FEMALE NPT to

FEMALE NPT

FEMALE NPT to

FEMALE NPT

Figure 22

NOTE: Gas shut-off shown. Other valves approved to use with

gas allowed.

Flex tubing to valve is pre-installed at the factory. Flare connector

is located in the envelope.

Anaccessiblemanualgasshut-offvalvemustbeinstalled

externaltothereplace.

GAS SUPPLY

41308-2-0620Page18

WARNING

If these instructions are not followed exactly, a re caus-

ing death or serious injury may occur.

Propane Cylinder Specications

Thisreplacecanbeusedwithanon-disposableself-contained

Propane Gas supply system:

• Propane cylinders may be acceptable for use with the

replaceprovidedtheyarecompatiblewiththereplace

retention means.

• Propane Gas supply cylinder must be constructed and

marked in accordance with the U.S. Department of

Transportation (D.O.T.) Specications for Propane Gas

Cylinders, or the Standard for Cylinders, Spheres and

Tubes for Transportation of Dangerous Goods and Com-

mission, CAN/CSA-B339 as applicable.

• Propane Gas supply cylinders between 4 and 40

poundsmusthaveanoverllpreventiondevice.

• Propane Gas supply cylinder must have a connection

devicecompatiblewiththeconnectionofthereplace.

• IfthereplaceisequippedwithaCGANo.600Cylinder

Connection Device, the cylinder must be disconnected

whenthereplaceisnotinuse.

• Ifreplaceistobepermanentlyconnectedtoagaspip-

ing system from a remote supply tank, installation must

be in accordance with local codes or, in the absence

of local codes, with the National Fuel Gas Codes ANSI

Z223.1/NFPA 54.

• Adentedorrustycylindermaybehazardousandshould

be checked by your propane supplier. Never use a cylin-

der with a damaged valve.

• Thisreplacemaybeusedwitha20lb.(9.1kg)or30lb

(13.6 kg) size propane cylinder only (not supplied).

• The propane cylinder must be provided with a shut-

off valve terminating in a propane cylinder valve type

QCC1, and a safety relief device having direct commu-

nication with the vapor space of the cylinder.

• The cylinder supply system must be arranged for vapor

withdrawal and the cylinder shall include a collar to

protect the cylinder valve.

• The Propane Gas cylinder must be provided with a

listedoverllprotectiondevice(OPD).Neverllthe

cylinderbeyond80percentfull.

• Do not store a spare Propane Gas cylinder under or

nearthisreplace.

• Use only a pressure regulator and hose assembly that

suppliesapressureof11in.watercolumntothere-

placeandhasaQCC1typetting.

• Cylinders to be used with this unit must be supplied with

aQCC1cylindervalve.AQCC1cylinderhasapositive

seatingconnection,whichwillnotallowgasowuntila

positive seal has been achieved. It is also equipped with

anexcessowdevice.Inordertoattainfullowtothe

replace,thevalvemustbeintheoffpositionwhenthe

cylinder valve is turned on.

WARNING

A re will result if the gas supply hose makes contact with

the underside of the replace.

Propane Gas

Attachcylinderretainingbracketsuppliedtothebaseofthecyl-

inder. Then secure to the surface to which it sits. Cylinder should

be on a level surface.

Cylinder Retaining Bracket

1. Fasten the bracket to the bottom of the propane bottle using

bolt and nut (not supplied).

2. Tighten the lag screw into the mounting surface leaving ap-

proximately 1/4 in. of thread above the surface.

3. Slide propane bottle into position so that the bracket slides

under the head of the lag screw.

4. Tighten the lag screw onto the bracket.

5. For fastening to a concrete surface a concrete anchor will be

required. (Not supplied)

Cylinder Connection: Ensure the gas regulator hose is kink

free. Remove the cap or plug from the cylinder fuel valve. Insert

theblackQCC1regulatornippleontotheQCC1fuelvalve.Hand

tightenclockwise.Donotusetools.Leaktestalljointspriorto

usingthereplace.Aleaktestmustbeperformedannuallyand

each time a cylinder is hooked up or if a part of the gas system

isreplaced.Ifthisreplaceistobeconnecteddirectlytoahouse

propane gas supply line, follow the instructions for the natural

gas hook-up.

Safety Considerations

• Make sure cylinder valve is in its full off position. (Turn clock-

wise to stop).

• Check cylinder valve features to ensure it has proper ex-

ternalmatingthreads.(CylinderValveMarked:USEWITH

TYPE1)

• Inspect hose for damage. Never attempt to use damaged or

plugged equipment. See your local Propane Gas Dealer for

repairs.

• When connecting regulator assembly to the cylinder valve,

hand tighten black QCC1 nut clockwise to a positive stop.

DO NOT use a wrench to tighten. Use of a wrench may dam-

age the quick closing coupling nut and result in a hazardous

condition.

• Locate the hose out of pathways where people may trip over

itorinareaswherethehosemaybesubjecttoaccidental

damage.

• Open cylinder valve fully (counter-clockwise). Turn the shut

off valve at the unit slowly to the on position and use a soapy

water solution to check all connections for leaks as indicated

inthediagramsbeforeattemptingtolightthereplace.Ifa

leakisfound,turntankvalveoffanddonotusethereplace

until repairs can be made.

FIREPLACE FRAMING AND INSTALLATION (CONT'D)

PROPANE GAS CYLINDER INFORMATION

41308-2-0620 Page 19

Enclosures For Propane Gas Supply Systems

Enclosures for Propane Gas supply cylinders shall be ventilated

byopeningsatthelevelofthecylindervalveandatoorlevel.

The effectiveness of the opening(s) for purposes of ventilation

shall be determined with the Propane Gas supply cylinder(s) in

place. This shall be accomplished by one of the following.

a. One side of the enclosure shall be completely open; or

b. For an enclosure having four sides, a top and a bottom:

1. Atleasttwoventilationopeningsatcylindervalvelevel

shall be provided in the side wall, equally sized, spaced

at180degrees(3.14rad),andunobstructed.Each

opening shall have a total free area of not less than

1/2 sq in per pound (2.3 sq. cm/kg) of stored fuel capac-

ity and not less than a total free area of 10 sq in (64.5

sq. cm).

2. Ventilationopening(s)shallbeprovidedatoorlevel

and shall have a total free area of not less than 1/2 sq in

per pound (3.2 sq. cm/kg) of stored fuel capacity and not

less than a total free area of 10 sq in (64.5 sq. cm). If

ventilationopeningsatoorlevelareinasideall,there

shall be at least two openings. The bottom of the open-

ingsshallbeatoorlevelandtheupperedgenomore

than5in.(127mm)abovetheoor.Theopeningsshall

beequallysized,spacedat180degrees(3.14rad)and

unobstructed.

3. Every opening shall have minimum dimensions so as to

permittheentranceofa1/8in.(3.2mm)diameterrod.

4. There shall be a minimum clearance of 2 in. (51 mm)

betweenthelowersurfaceoftheoorofthePropane

Gas supply cylinder enclosure and the ground.

• Cylinder valves shall be readily accessible for hand opera-

tion.Adoorontheenclosuretogainaccesstothecylinder

valves is acceptable, provided it is non-locking and can be

opened without the use of tools.

• Thedesignofthereplaceshallbesuchthat(1)the

Propane Gas supply cylinder(s) can be connected, discon-

nected and the connections inspected and tested outside the

cylinder enclosure; and (2) those connections which could

be disturbed when installing the cylinder(s) in the enclosure

can be leak tested inside the enclosure;

• Ventilation openings in sidewalls shall not communicate

directlywithotherenclosuresofthereplace.

The enclosure for the Propane Gas cylinder shall isolate the

cylinder from the burner compartment to provide:

a. Shielding from heat radiation;

b. Aamebarrier;and

c. Protection from foreign material.

Be certain to mount or set the Propane Gas cylinder on a at

surface and restrain it using a cylinder retaining bracket to

prevent it from tipping.

NON-LOCKING

DOOR

TOP AND SIDE PARTITION

TO ISOLATE TANK FROM

FIREPLACE

OPENING B

OPENING A

1” MAX

5” MAX

TOP AND SIDE PARTITION

TO ISOLATE TANK FROM

FIREPLACE

FIREPLACE POSITIONED

ABOVE TANK ENCLOSURE

FIREPLACE POSITIONED

BESIDE TANK ENCLOSURE

5” MAX

1” MAX

2” MIN

Cylinder

Size

Opening

Area A

Opening

Area B

Recommended

Dimension C

20lb

(9.1kg)

20 sq.in.

(130cm

)

10 sq.in.

(65cm

)

34 in.

(863mm)

30lb

(13.6kg)

30 sq.in.

(195cm

)

15 sq.in.

(100cm

)

34 in.

(863mm)

NOTE: There shall be a minimum clearance of 2 in. (51 mm)

betweenthelowersurfaceoftheoorofthePropaneGassupply

cylinder enclosure and the ground.

Figure 23

FIREPLACE FRAMING AND INSTALLATION (CONT'D)

PROPANE-GAS CYLINDER INFORMATION

41308-2-0620Page 20

FIREPLACE FRAMING AND INSTALLATION (CONT'D)

FINISHING

1. Aftergasandelectricalhookupiscompleted,lowerand

secure the burner assembly (leave two supports in bottom of

replaceforfutureuse)withthetwoscrewsremovedinStep

9 on page 13.

2. Installtheglasswindpanel(twousedonsee-throughre-

places). The glass panel has a low emission (low-E) coating

applied to one side. The panel must be installed with the

low-E coating facing the burner. The panel will have a sticker

located in the bottom corner of the side which has the low-E

coating. Install the glass panel with the sticker facing the

burner and the bottom of the panel. See Figure 24.

DO NOT REMOVE THE STICKER before installing the

glass panel. It is located on the panel such that it should not

be visible after the control door is installed. This will allow

easyidenticationofthelow-Esideoftheglassiftheglass

panel is ever removed for service.

If the sticker is not on the glass panel, the low-E side of the

glass can be determined by using a multimeter/ohmmeter.

The low-E coating will conduct electricity. Set the meter

toreadresistance(Ω).Holdtheprobesagainsttheglass

surface approximately 1 inch apart. If the meter displays a

resistance reading (indicating continuity), this is the side of

the glass panel which has the low-E coating.

LOW-E

LOW-E Sticker on

opposite side of glass

Figure 24

3. Reinstallthepivotboltsandwashersremovedinstep8on

page 13 and reinstall the control door.

4. UnscrewtheigniterbuttonandinstalltheAAbatteryprovided

in the instruction envelope prior to closing the control door. See

Figure 25.

Figure 25

Framing and Finishing

Thereplacecanbeinstalledwithpanelsaroundtheopeningas

a clean face installation. See Figure 26. The top and sides must

use non-combustible panels (provided) where shown going over

thefaceofthereplace.Outsideofthisarea,anyweatherproof

wall board may be used.

Figure 26

Thereplacecanalsobeinstalledwithpanelsushwiththe

faceofthereplace.See Figure 27. In this application, the two

top non-combustible panels (provided) are required above the

replace.Outsideofthisareaincludingthesidesoutsideofthe

replace'smetalmaybeanyweatherproofwallboard.

Figure 27

To complete installation place non-combustible panels above

replaceopening.Centerpanelsonreplaceandsecurewith

screws into frame. With the non-combustible panels in posi-

tion,predrill1/8-in.diameterholesthroughthenon-combustible

panels and top mounting standoffs before running the screws into

the top mounting standoff. Place non-combustible panels on the

sidesofthereplaceopening.Securewithscrewsintotheframe

andpre-drill1/8-in.diameterholesintothereplaceface.Finish

remaining wall with weather-proof wall board.

NOTE:Ifinstallingthewallboardintheushfaceconguration,

trim the two top panels to 16-1/2 in. x 26-3/4 in. The smaller non-

combustible panels will not be needed.

NOTE:Areaswherethelmhasbeenformed(corners,hems,

etc.)mayrequireextracleaningduetothepropertiesofthelm.

Ensurethatallprotectivelmhasbeenremovedfromthere-

place prior to burning.

La page est en cours de chargement...

American Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

Marque: American Hearth

Modèle: Outdoor Linear Fireplace 48 (OLL48FP/SP)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

OLL48FP/SP

Télécharger le PDF

rapport

dans d''autres langues

English: American Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Owner's manual

American Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

Ce manuel convient également à

American Hearth Outdoor Linear Fireplace 48 (OLL48FP/SP) Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents