American Hearth OL48TP, OL60TP Le manuel du propriétaire

Marque: American Hearth

Modèle: OL48TP, OL60TP

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

Outdoor Linear Fire Pit (OL48TP, OL60TP)

Page 1

OUTDOOR LINEAR GAS

FIREPLACE MODELS

OL48TP10(N,P)-1

OL48TP18(N,P)-1

OL60TP10(N,P)-1

OL60TP18(N,P)-1

GAS-FIRED

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon

monoxide which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed

space such as a camper, tent, car or home.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ame.

3. If odor continues, keep away from the

appliance and immediately call your gas

supplier or re department.

WARNING

For Outdoor Use Only.

WARNING

Improper installation, adjustment, alteration,

service or maintenance can cause injury

or property damage. Read the installation,

operating and maintenance instructions

thoroughly before installing or servicing this

equipment.

WARNING

Do not store or use gasoline or other

ammable vapors and liquids in the vicinity

of this or any other appliance.

An Propane-cylinder not connected for use

shall not be stored in the vicinity of this or

any other appliance.

Installation and service must be performed

by a qualied installer, service agency or

the gas supplier.

WARNING

If the information in these instructions are

not followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

WARNING

If not installed, operated and maintained

in accordance with the manufacturer's

instructions, this product could expose you

to substances in fuel or from fuel combustion

which can cause death or serious illness.

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

37795-3-0119Page 2

BEFORE YOU START

1. Read the safety information on pages 4 and 5.

2. What to consider before installing. See pages 9 and 10.

3. Water drainage is required. See page 12. Optional drain tray

available.

4. Where are you going to install the unit? See pages 9 to 12.

5. Enclosure construction. See pages 9 to 17.

6. Installtherepit.(ModelswithLEDlightsinstalled)

See pages 13 to 20.

7. Connect the electricity. See page 13.

8. Connect the gas. See pages 14 to 16.

9. Install the crushed glass. See page 20.

10. Lighttherepitandtroubleshoot.Seepages21and22.

11. Showthehomeownerhowtooperatetherepit.Seepages

21 to 23.

12. Showthehomeownerhowtodothebasicmaintenance.

See page 25.

Tools Needed:

(1)-1/8-inchAllenWrench

(2)-Adjustablewrencheswithrangeof1-inchforgasconnection

(2)-Adjustablepipewrenches

(1)-PhillipsScrewdriver

(1)-5/16"HexNutDriver

CARTON CONTENTS

Index

No.

Description

Quantity Supplied

OL(48,60)TP10 OL(48,60)TP18

Instruction

Envelope

1 1

2 Receptacle - 1

3 Cover Plate - 1

Conduit

Connector1/2-in.

- 1

5 AABattery 1 1

6 Prop Tool 2 2

SeePartsListsonpage29fororderingreplacementparts.Do

notorderbatteries,bolts,screws,washersornuts.Theyare

standardhardwareitemsandcanbepurchasedatanylocal

hardwarestore.

37795-3-0119 Page 3

TABLE OF CONTENTS

Before You Start .......................................................................................................................... 2

Table Of Contents ....................................................................................................................... 3

Important Safety Information ..................................................................................................... 4

Safety Information For Users Of Propane Gas ........................................................................ 5

Product Specications ............................................................................................................... 6

Accessories................................................................................................................................. 6

Firepit Dimensions ..................................................................................................................... 7

Introduction ................................................................................................................................. 8

Combustible Materials ............................................................................................................. 11

Clearances................................................................................................................................. 11

Planning Installation ............................................................................................................ 9 - 12

Firepit Installation:

-ElectricalSupply .................................................................................................................. 13

-GasSupply .......................................................................................................................... 14

-PropaneGasCylinderInformation................................................................................ 15-16

-FirepitEnclosureRequirements.................................................................................... 17-18

-Finishing........................................................................................................................ 19-20

Lighting Instructions ................................................................................................................ 21

Main Burner Flame Characteristics ........................................................................................ 22

Operation Instructions / LED Lights ....................................................................................... 23

Wiring ......................................................................................................................................... 24

Maintenance .............................................................................................................................. 25

Troubleshooting ........................................................................................................................ 26

Master Parts Distributor List ................................................................................................... 27

How To Order Repair Parts ...................................................................................................... 27

OL48TP Parts List ..................................................................................................................... 28

OL60TP Parts List ..................................................................................................................... 28

OL48TP Parts View ................................................................................................................... 29

OL60TP Parts View ................................................................................................................... 29

Firepit Service History.............................................................................................................. 30

Warranty Terms ......................................................................................................................... 31

SECTION PAGE

37795-3-0119Page 4

IMPORTANT SAFETY INFORMATION

SAMPLE WARNINGS AND DEFINITIONS:

DANGER:Indicatesahazardoussituationwhich,ifnot

avoided,willresultindeathorseriousinjury.

WARNING:Indicatesahazardoussituationwhich,ifnot

avoided,couldresultindeathorseriousinjury.

CAUTION:Indicatesahazardoussituationwhich,ifnot

avoided,couldresultinminorormoderateinjury.

NOTICE:Addressespracticesnotrelatedtopersonalinjury.

DANGER

• Children and adults should be alerted to the hazard of

high surface temperature and should stay away to avoid

burns or clothing ignition.

• Young children should be carefully supervised when

they are in the same area with the repit.

• Clothing or other ammable materials should not be

hung near the repit, or placed on or near the repit.

• Keep the repit area clear and free from combustible

material, gasoline and other ammable vapors and

liquids.

• Never lean over the repit when lighting, or during

operation.

WARNING

• Do not place debris, logs, or other articles in repit

during operation.

• Any modication to controls can be dangerous. Improper

installation can cause serious injury or death from re,

burns, explosion or carbon monoxide poisoning.

• Make a periodic visual check of burners. Clean and

replace damaged parts.

• Never use the repit for cooking.

• Installer: Please leave these instructions with the owner

for future reference

• This unit complies with ANSI Z21.97/CSA 2.41 for Outdoor

Gas Fireplaces.

• Installation and repair should be done by a QUALIFIED

SERVICE PERSON. This repit should be inspected before

use and at least annually by a professional service person.

More frequent cleaning may be required due to insects,

pollen build up, dust, etc. It is imperative that the control

compartments, burners, and circulating air passageways

of the repit be kept clean.

• During manufacturing, fabricating and shipping, various

components of this repit are treated with certain oils,

lms or bonding agents. These agents are not harmful,

but may produce annoying smoke and smells as they are

burned off during initial operation of the repit. This is a

normal temporary occurrence.

• Follow all local codes regarding installation, combustion

and ventilation air or in the absence of local codes follow

the National Fuel Gas Code ANSI Z223.1 (US installation),

or CAN/CGA-B149, installation Code (Canada installation).

• Inspect the burner at least once a year.

• Keep burner and control compartment clean.

• DO NOT use this repit if any part has been under water.

Immediately call a qualied service technician to inspect

the repit and to replace any part of the control system

and any gas control which has been under water.

• Any guard or other protective device removed for servicing

the appliance must be replaced prior to operating the

appliance.

This manual includes warnings intended to help protect you during the installation and use of this product. Each warning begins

with the alert symbol and an alert word in bold letters—followed by the specics of the warnings. Please review the sample

warnings below.

ABOUT (WARNING) INFORMATION BELOW

37795-3-0119 Page 5

SAFETY INFORMATION FOR USERS OF PROPANE GAS

Propane is a ammable gas which can cause res and explo-

sions. In its natural state, propane is odorless and colorless.

You may not know all the following safety precautions which

can protect both you and your family from an accident. Read

them carefully now, then review them point by point with the

members of your household. Someday when there may not

be a minute to lose, everyone’s safety will depend on knowing

exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas

because of the odorant put in the Propane Gas.

That's your signal to go into immediate action!

• Donotoperateelectricswitches,lightmatches,useyourphone.

Donotdoanythingthatcouldignitethegas.

• Geteveryoneoutofthebuilding,vehicle,trailer,orarea.Do

thatIMMEDIATELY.

• Closeallgastankorcylindersupplyvalves.

• PropaneGasisheavierthanairandmaysettleinlowareas

such as basements. When you have reason to suspect a gas

leak,keepoutofbasementsandotherlowareas.Stayoutuntil

reghtersdeclarethemtobesafe.

• Useyourneighbor’sphoneandcallatrainedPropaneGas

servicepersonandtheredepartment.Eventhoughyoumay

notcontinuetosmellgas,donotturnonthegasagain.Donot

re-enterthebuilding,vehicle,trailer,orarea.

• Finally, lettheservicemanandreghterscheckforescaped

gas.Havethemairouttheareabeforeyoureturn.Properly

trainedPropaneGasservicepeople should repair the leak,

thencheckandrelightthegasreplaceforyou.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell

the odor of the chemical put into the gas. You must nd out if

you can smell the odorant in propane.Smokingcandecrease

yourabilitytosmell.Beingaroundanodorforatimecanaffectyour

sensitivity or ability to detect that odor. Sometimes other odors in

theareamaskthegasodor.Peoplemaynotsmellthegasodoror

theirmindsareonsomethingelse.Thinkingaboutsmellingagas

odorcanmakeiteasiertosmell.

The odorant in Propane Gas is colorless, and it can fade under

some circumstances. Forexample, if thereis anunderground

leak,themovementofthegasthroughsoilcanltertheodorant.

OdorantsinPropaneGasalsoaresubjecttooxidation.Thisfading

canoccurifthereisrustinsidethestoragetankorinirongaspipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls,masonryandothermaterialsandfabricsinaroom.Thatwill

takesomeoftheodorantoutofthegas,reducingitsodorintensity.

PropaneGasmaystratifyinaclosedarea,andtheodorintensity

could vary at different levels. Since it is heavier than air, there may

bemoreodoratlowerlevels.Alwaysbesensitivetotheslightestgas

odor.Ifyoudetectanyodor,treatitasaseriousleak.Immediately

go into action as instructed earlier.

SOME POINTS TO REMEMBER

• LearntorecognizetheodorofPropaneGas.YourlocalPropane

GasDealercangiveyoua“ScratchandSniff”pamphlet.Use

ittondoutwhatthepropaneodorsmellslike.Ifyoususpect

thatyourPropaneGashasaweakorabnormalodor,callyour

PropaneGasDealer.

• Ifyouarenotqualied,donotlightpilotlights,performservice,

ormakeadjustmentstoreplacesonthePropaneGassystem.

Ifyouarequalied,consciouslythinkabouttheodorofPropane

Gaspriortoandwhilelightingpilotlightsorperformingservice

ormakingadjustments.

• Odorfade,duetooxidationbyrustoradsorptiononwallsof

newcylindersandtanks,ispossible.Therefore,peopleshould

beparticularlyalertandcarefulwhennewtanksorcylinders

areplacedinservice.Odorfadecanoccurinnewtanks,or

reinstalledoldtanks,iftheyarelledandallowedtosettoo

longbeforerelling.Cylindersandtankswhichhavebeenout

ofserviceforatimemaydevelopinternalrustwhichwillcause

odorfade.Ifsuchconditionsaresuspectedtoexist,aperiodic

sniff test of the gas is advisable. If you have any question

about the gas odor, call your Propane Gas Dealer. A peri-

odic sniff test of the Propane Gas is a good safety measure

under any condition.

• If,atanytime,youdonotsmellthePropaneGasodorantand

youthinkyoushould,assumeyouhavealeak.Thentakethe

same immediate action recommended above for the occasion

whenyoudodetecttheodorizedPropaneGas.

• Ifyouexperienceacomplete“gasout,”(thecontainerisunder

novaporpressure),turnthetankvalveoffimmediately.Ifthe

containervalveislefton,thecontainermaydrawinsomeair

throughopeningssuchaspilotlightorices.Ifthisoccurs,some

newinternalrustingcouldoccur.Ifthevalveisleftopen,then

treatthecontainerasanewtank.Alwaysbesureyourcon-

tainer is under vapor pressure by turning it off at the container

beforeitgoescompletelyemptyorhavingitrelledbeforeitis

completely empty.

37795-3-0119Page 6

PRODUCT SPECIFICATIONS

DECORATIVE CRUSHED GLASS

Required Decorative Crushed Glass Media Kits (5 Sq. Ft. Minimum, 7 Sq. Ft. Maximum) Required for

OL48 Burner and LED Lighting, and (6 Sq. Ft. Minimum, 8 Sq. Ft. Maximum) for OL60 Burner and LED Lighting

Model Description

DG1CLF* ClearFrost

DECORATIVE CRUSHED GLASS (FOR ACCENT ONLY)

Model Description Model Description

DG1BKP* BlackPolished DG1BCR Copper

DG1BUC* Blue DG1BZR Bronze

*ClearFrostDecorativeCrushedGlassisrecommended,ifrepitisequippedwithLEDlighting.DecorativeGlassDropletscannotbe

substitutedforcrushedglass.Onebagofcrushedglasscovers1sq.ft.Glasscolorsmaybemixed.ThemaximumamountofCrushed

DecorativeGlassallowedis8bagsonOL60,and7bagsonOL48.TransparentandTranslucentcrushedglasswillallowLEDsto

maximizebrightnessofLEDlighting.

DECORATIVE GLASS DROPS & DROPLETS (MAY BE USED IN ADDITION TO CRUSHED GLASS AS AN ENHANCEMENT)

Model Description Model Description

DG1NXS 1-in.DecorativeGlassDrops-OnyxSolid DG1AB 1/2-in.DecorativeGlassDroplets-AquaBlue

DG1RYC 1-in.DecorativeGlassDrops-RubyClear DG1GC 1/2-in.DecorativeGlassDroplets-GlacierIce

DG1TZC 1-in.DecorativeGlassDrops-TopazClear DG1SL 1/2-in.DecorativeGlassDroplets-SangriaLuster

NOTE:

DecorativeGlassDropletsmaybeaddedontopofthecrushedglassasanenhancement.DecorativeGlassDropletsmustnotbe

placedintheburnerame.SeeCrushedGlassInstallation,Page22.DonotaddmorethanonebagofDecorativeglassdroplets.

ACCESSORIES

Model

Description

OL48TP OL60TP

DT48LSS DT48LSS StainlessSteelDrainTray-(Fits48and60-inchrepits)

WC48LSS WC60LSS Stainless Steel Weather Cover

WG484LT WG604LT DeectorGlassKit(Forwindyapplications)

37992 37993 NaturaltoPropaneConversionKit

37991 37994 PropanetoNaturalConversionKit

BBA BBA Tilt-OutPropaneTankDoorKit

BRB BRB VentRegisterKit(Includes2vents)

ACCESSORIES

Model

Number

BTUH

Max. Rate

BTUH

Min. Rate

Gas

Type

Valve

Type

Orice

Size

Air Shutter

Setting

OL48TP10N 55,000 39,500 Natural MANUAL 24 1/16in.Open

OL48TP10P 55,000 35,500 Propane MANUAL 43 3/8in.Open

OL48TP18N 55,000 39,500 Natural MANUAL 24 1/16in.Open

OL48TP18P 55,000 35,500 Propane MANUAL 43 3/8in.Open

OL60TP10N 65,000 46,500 Natural MANUAL 12 1/16in.Open

OL60TP10P 65,000 38,000 Propane MANUAL 41 FullyOpen

OL60TP18N 65,000 46,500 Natural MANUAL 12 1/16in.Open

OL60TP18P 65,000 38,000 Propane MANUAL 41 FullyOpen

Natural Gas Propane Gas

ManifoldPressureSetting 4-1/2"w.c. 11"w.c.

GasInletPressureMax 7"w.c. 11"w.c.

37795-3-0119 Page 7

FIREPIT DIMENSIONS

Index

Letter

Dimension Description

OL48TP OL60TP

Dimensions In Inches

A TheMaximumHeightofTheFirepit

73/8 73/8

B TheMaximumWidthofTheFirepit

53 65

C TheMaximumDepthofTheFirepit

237/8 237/8

D TheMaximumDepthofTheCrushedGlassBed

1311/16 1311/16

E TheMaximumWidthofTheCrushedGlassBed

467/8 587/8

F EndGasLineOpeningsFromCenterlineofFirepit

6 6

G EndGasLineOpeningsFromBottomofFirepit

29/16 29/16

H EndElectricalOpeningHeightFromBottomofFirepit

25/16 25/16

I BottomElectricalOpeningsFromEndofFirepit

11/16 11/16

J BottomGasLineOpeningsFromEndofFirepit

115/16 115/16

K BottomElectricalOpeningsFromCenterlineofFirepit

31/4 31/4

L BottomGasLineOpeningsFromCenterlineofFirepit

5 5

M BottomCabinetDepth

227/16 227/16

N BottomCabinetWidth

513/4 633/4

O BottomDrainHoleLocationsFromCenterline

5 5

P BottomDrainHoleLocationsFromCenterline

21 21

TOP VIEW

SIDE VIEW

BOTTOM VIEW

END VIEW

DRAIN

HOLES (6)

Figure 1

Figure 2

Figure 3

Figure 4

37795-3-0119Page 8

INTRODUCTION

Qualied Installing Agency

Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performedonlybyaqualiedagency.Theterm"qualiedagency"

meansanyindividual,rm,corporationorcompanywhicheitherin

person or through a representative is engaged in and is responsible for

(a)theinstallationorreplacementofgaspipingor(b)theconnection,

installation,repairorservicingofequipment,whoisexperiencedin

suchwork,familiarwithallprecautionsrequiredandhascomplied

withalltherequirementsoftheauthorityhavingjurisdiction.

Local Codes

• Whentherepitisconnectedtoaxedpipingsystem,thein-

stallationmustconformwithlocalcodes,orintheabsenceof

localcodeswiththeNational Fuel Gas Code, ANSI Z223.1/

NFPA 54, or International Fuel Gas Code.

• Wheninstalled,therepitmustbeelectricallygrounded

inaccordancewithlocalcodes,orintheabsenceoflocal

codeswiththeNational Electrical Code, ANSI/NFPA 70, if

applicable.

Commonwealth of Massachusetts: The installation must be

madebyalicensedplumberorgastterintheCommonwealth

ofMassachusetts.

Theinstallationmustconformwithlocalcodesor,intheabsence

oflocalcodes,withtheNationalFuelGasCode,ANSIZ223.1.*

*Available from the American National Standards Institute, Inc. 1430

Broadway, New York, N.Y. 10018.

High Altitudes

Foraltitudes/elevationsabove2,000feet(610m),ratingsshouldbe

reducedattherateof4percentforeach1,000feet(305m)above

sea level. Contact the manufacturer or your gas company before

changingspud/oricesize.

Conversion Kits

Conversionkitsareavailable.Seepage6.Installationofaconversion

kitshouldbedonepriortoapplyingmediamaterialstotheburner

and screen areas.

Instructions to Installer

1. Installermustleaveinstructionmanualwithownerafter

installation.

2. Installermusthaveownerlloutandmailregistrationcard

suppliedwiththisrepitorregisteronlineat

www.empirecomfort.com.

3. Installershouldshowownerhowtostartandoperateoutdoor

repit.

AlwaysconsultyourlocalBuildingDepartmentregardingregulations,

codesorordinanceswhichapplytotheinstallationofanoutdoor

gasreplace.

WARNING

To avoid injury or damage to the repit or surrounding area,

do not burn wood or other solid fuels in this repit.

WARNING

Any change to this repit or its controls can be dangerous.

Improper installation or use of the repit can cause serious

injury or death from re, burns, explosion or carbon monoxide

poisoning.

Thisseriesisdesigncertiedinaccordancewith

ANSI Z21.97/CSA

2.41 for Outdoor Gas Fireplaces

and should be installed according

to these instructions.

Any alteration of the original design, installing it other than as

shown in these instructions or using a type of gas not shown

on the rating plate, is the responsibility of the person and

company making the change.

Manual Valve Safety System

Whentheburnerignites,athermocouplesensesasignal(electrical

current)thatenergizesamagnetinthegasvalve.After30to60

seconds,thecontrolknobcan be released. Ifthethermocouple

doesnotsensetheame,thegaswillshutoff.

Important

AllcorrespondenceshouldrefertocompleteModelNumber,Serial

Numberandtypeofgas.

Moisture Resistance

Whenpurchasingarepitwerecommendyoualsobuyaweather

covertoprotecttheunitfromexcessivemoisture.Neverinstalla

burnerwheremoisturecannotdrainoffeasily.

NOTICE:Thisrepitisdesigncertiedasanoutdoorgasreplace,

thereforesomereferencesmaystate"replace"asrequiredbythe

ANSI Z 21.97/CSA 2.41standardforoutdoorgasreplaces.

37795-3-0119 Page 9

What to Consider Before Installing

1. Verifyrepitgastypeandgassupplytypearethesame.

2. Lookforalocationwherecombustibleswillnotinterfere.

3. 120VGFIpoweroutletwillbeneededforLEDlights

4. Choose a location for gas shutoff valve. Installation requires that

anaccessableexternalgasshutoffbeinstalled.(Notprovided)

5. Verify ventilation meets at least minimum requirements

6. Drainageunderrepit.

7. Drainpanandweathercoveraccessories.(optional)

8. Glasswindkitaccessories(optional)

Whenplanningtheinstallationfortherepit,determinewherethe

unitistobeinstalledandwhetheroptionalaccessoriesaredesired.

Gassupplypipingshouldalsobeplannedatthistime.

Therepitcanbemountedonanyofthesesurfaces:

1. Araisedframeofcombustiblematerial.

2. Brick,block,orstonebaseinstallation

Contactmustbemadeonallfourperimeterangeswithadepth

ofleast7-1/2inchestoretaintherepit.Internalopening

dimensionsareshowninFigure 5. Enclosures should include

provisionforwaterdrainage.

Figure 5

OL48TP OL60TP

Internal Enclosure Dimensions (inches)

HeightA *7-1/2Min. *7-1/2Min.

WidthB 51-3/4Min.

52-1/2Max.

63-3/4Min.

64-1/2Max.

DepthC 22-5/8Min.

23-1/2Max.

22-5/8Min.

23-1/2Max.

*Ifinstallingadraintrayaccessary,addatleast6"inchesmoreto

theheightoftheenclosuretoallowenoughspaceforthedrainpan,

connector, and tubing clearance.

Atthispoint,youshouldhavedecidedwhatcomponentstoinclude

inyourinstallation,andwheretherepitistobelocated.Ifthishas

notbeendone,stopandconsultyourdealerforassistancewith

this planning.

WARNING

This repit is intended for installation on an outdoor patio

or yard. This repit shall be used only outdoors in a well

ventilated space and shall NOT be used in a building, garage,

or other enclosed area. This repit cannot be installed with

an opening to the inside of a residence.

NOTICE: This repit is NOT equipped with an Oxygen Depletion

Sensor (ODS) pilot.

Installationoftherepitmaybeinan"open"area,howeveritis

recommendedthatthisrepitbeinstalledinanareashelteredfrom

directwinds.

Directwindwillcauseanerraticameandpossibleburneroutage.

Thiserraticamecouldalsoleadtoexcessiveblacksoot.These

are nuisance issues rather than safety issues.

Typical installation may include covered patio, open porch, gazebo

oranoutsidewallofahouse.

• Minimumporcharea–96squarefeet

• Minimumceilingheight–48inches

LEDLightswillrequirea120VGFIpoweroutletonthevalveend

oftherepit.TheGFIplugwillbelocatedoutsideoftherepit.A

junctionboxisprovidedinsidetherepittoprovidealocationto

plugintheLEDs.

Outdoor Firepit Location Requirements

Do not install repit until all necessary provisionsare made for

combustionand ventilation air.Consult the written instructions

providedwiththerepitforinformationconcerningcombustionand

ventilationair.Intheabsenceofinstructions,refertotheNational

FuelGasCode,ANSIZ223.1/NFPA 54,Airfor Combustion and

Ventilation, or applicable local codes.

Installation in partial enclosuresmust conform with one of the

followingconditions:

• Withwallsonbackandoneside,butwithnooverheadcover.

See Figures 6.

12”

MIN

STUDWALL

12”

TOP VIEW

Figure 6

• Withinapartialenclosurewhichincludesanoverheadcover

andnomorethantwosidewalls.Thesesidewallsmaybe

parallel,asinabreezeway.See Figures 7 and 8.

STUDWALL

TOP VIEW

3 1/4”

MIN

3 1/4”

MIN

Figure 7

FIREPIT

Figure 8

PLANNING INSTALLATION

37795-3-0119Page 10

PLANNING INSTALLATION (CONT'D)

Installationispermissablewithinapartialenclosurethatincludes

anoverheadcoverandthreesidewalls,aslongas30percentor

moreofthehorizontalperiphery(perimeterofwallsandopenside)

of the enclosure is permanently open. See Figures 9,10 and 11.

12”

MIN

STUDWALL

12”

TOP VIEW

Figure 9

FIREPIT

Figure 10

Ifinstallinginascreenedinporch,theopenspacemustbeadjusted

(increased)from30percent(adjustedopenspace=30%/%open

areaofthescreenmesh)."Example,ifyouusedascreenwitha

66%openarea,theminimumopenspaceofyourbuildingmust

be46%oftheperiphery.Ifyouhaveacoveredscreened-inporch

thathastwosidewallsthatare16',onewallthatwasagainstthe

housethat's20'andoneopensidethat's20',youwouldhavea

perimeterof72'.Youwouldneedtohave33'oftheperimeteropen

(72'x46%=33')."

(Contact your screen manufacturer or screen dealer to determine

your screens open area).

48” MIN

SIDE VIEW

12”

FIREPIT

Figure 11

CAUTION

Vinyl Soft, Vinyl Ceiling, Vinyl Overhang Disclaimer

Clearances

are to heat resistant material (i.e. wood, metal). This does

not include vinyl. Empire Comfort Systems Inc. will not be

held responsible for heat damage caused from terminating

under vinyl overhangs, vinyl ceilings or vinyl ventilated/

unventilated softs.

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause property damage, personal injury

or loss of life. Installation and service must be performed

by a qualied installer, service agency or the gas supplier.

GAS LINE CONNECTION

Therepitisdesignedtoaccepta3/8-in.gaslineonOL48TPunits,

anda1/2-in.gaslineonOL60TPunits.Havethelineinstalledby

aqualiedservicepersoninaccordancewithallbuildingcodes.

Consult local building codes to properly size the gas supply line

leadingto the gas hook-up atthe unit.TheCommnowealth of

Massachusettsrequiresthataexiblereplaceconnectorcannot

exceedthreefeetinlength.See Figure 12.

Aex-lineconnectiontothevalvesisprovided.The gas shut-off

valve (not supplied) must be located outside of the unit in an

accessible area.

Checkgastypeontheratinglabellocatedontheundersideofthe

control door. If the gas listed on the rating label does not match

yourgassupply,DONOTINSTALL.Contactyourdealerforproper

modelorconversionkit.

AlwaysuseanexternalregulatorforallPropanereplacestoreduce

thesupplytankpressuretoamaximumof11in.w.c.

WARNING

Connection directly to an unregulated L.P. tank can cause

an explosion.

WARNING

Risk of re, explosion or asphyxiation. Ensure no ignition,

ame or spark are near during installation. This includes

cigarettes or cell phones.

Leaktestallconnectionswithasoapandwatersolution.Bubble

formationwillindicatealeakwhileunderpressure.Usecautionto

avoid burns.

37795-3-0119 Page 11

Side Wall Clearances

Theclearancefromtheedgeoftheglassbedintherepittoany

combustiblewallshouldnotbelessthan3-1/4inches.

NOTICE:Forinstallationswitharearwallandsidewall,referto

Figures 6 and 9.

NOTICE:Seepages9and10foradditionalwallandceiling

clearances to combustibles.

Minimum Ceiling Clearances

Ceiling Clearances: The ceiling height should not be less than

48inchesfromthetopsurfaceoftherepit.

Rear Wall Clearances

Theclearancefromtheedgeoftheglassbedintherepittoany

combustiblerearwallshouldnotbelessthan12inches.

CAUTION

Vinyl siding must not be installed within 24 inches of the

edge of the glass bed in the repit.

PLANNING INSTALLATION (CONT'D)

Nogreetingcards,stockingsorornamentationofanytypeshould

beplacedovertherepit.Thisisanopenameappliance.Theow

ofheatandamescanignitecombustibles.

No vinylsidingmaterialscanbeinstalledwithin24inchesofthe

crushedglassareaontherepit.

REAR

SIDE

3-wall alcove not allowed.

Figure 13

REAR

SIDE

CEILING

3-wall alcove with ceiling not allowed.

Figure 14

CLEARANCES

COMBUSTIBLEMATERIALS

0” TO FRONT

AND REAR SIDES

0” TO BOTTOM

0” TO

LEFT AND

RIGHT SIDES

COMBUSTIBLE CLEARANCE REQUIREMENTS

Figure 12

COMBUSTIBLECLEARANCEREQUIREMENTS

37795-3-0119Page 12

MODEL GAS FLEX LINE CONNECTION

OL48TP Use3/8inchmaleareconnection

OL60TP Use1/2inchmaleareconnection

Figure 15

WATER DRAINAGE REQUIREMENT

Provisionsmustbemadetodrainwaterawayfromtheunit.An

optionaldrainpancanbepurchasedfromyourEmpireDealerto

tundertherepit.Ifinstallingtheoptionaldrainpan,itmustbe

installedpriortoinstallingtherepit.Formoreinformation,refer

totheinstallationinstructionssuppliedwiththedrainpan.Ifthis

drainisnotused,otherwaterdrainageisrequiredtoowaway

fromtheinstalledrepitcustombaseconstruction.See Figure 3

for drain hole locations.

ELECTRICAL CONSIDERATIONS (LED Lighted Units Only)

Afactoryinstalledjunctionboxislocatedonthelowerrightside

oftherepit.Thejunctionboxandwiringmayberelocatedto

theoppositesideoftherepitifdesired.Wiringtothejunction

boxmustbemetalcladorenclosedinaconduitandmustbe

approvedforoutdooruse.ConnectthewiringtoanexternalGFI

protectedoutletinstalledneartherepit.Refertoelectricalsupply

section for additional information on pages 13 and 24.

PLANNING INSTALLATION (CONT'D)

37795-3-0119 Page 13

FIREPIT INSTALLATION

GFI

OUTLET

Figure 16

GROUND

CONDUIT

RECEPTACLE

120 VOLT

POWER SUPPLY

OUTLET

COVER

GASKET

TRANSFORMER

POWER

CORD

Figure 17

ELECTRICALSUPPLY

FOR FIREPITS WITH LED LIGHTS ONLY

CAUTION

All wiring should be done by a qualied electrician and

shall be in compliance with all local, city and state building

codes. Before making the electrical connection, make sure

that the main power supply is disconnected. The repit,

when installed, must be electrically grounded in accordance

with local codes, or in the absence of local codes, with the

National Electrical Code ANSI/NFPA 70 (Latest Edition).

Wiringtothejunctionboxmustbemetalcladorenclosedina

conduitandmustbeapprovedforoutdooruse.Aconnectorfor

thejunctionboxtoaccommodate1/2-in.conduitissuppliedinthe

instructionenvelope.Therepitreceptaclemustbeconnected

toanexternalGFIprotectedoutletinstalledneartherepit.See

Figure 16.

RoutethewiringfromtheexternalGFIoutletthroughtheconduit

tothejunctionbox.Leaveapproximately6-in.ofwireinthe

junctionboxforconnection.

Retrieve the receptacle and cover from the instruction envelope.

Attachtheblackwiretothegoldscrewandwhitewiretothe

silverscrewofthereceptacle.Thegroundwireshouldbe

attachedtothegreengroundscrewonthejunctionboxandthe

receptacle. See Figure 17.

Placereceptacleinpositionandattachcoverplate.Makesurethe

coverplatedoorsopenupward.Besuretotestthereceptacleto

ensuretheGFIcircuitfunctionsproperly.Plugtransformerpower

cord into receptacle, and close the unused receptacle door.

See

Figure 17.

37795-3-0119Page 14

FIREPIT INSTALLATION (CONT'D)

• Solidfuelsshallnotbeburnedinthisrepit.

• Themaximumgasinletsupplypressureis11in.forPropane

and7in.forNatural.

• Forrepitswithaxedfuelpipingsystemandequippedwith

a gas pressure regulator, the required manifold pressure in

incheswatercolumn:11in.forPropaneand

4.5in.Natural.

• Forrepitswithaxedfuelpipingsystemandequippedwith

arepitgaspressureregulator,therepitanditsindividual

shutoff valve must be disconnected from the gas supply pip-

ing system during any pressure testing of that system at test

pressuresinexcessof1/2psi(3.5kPa).

Therepitmustbeisolatedfromthegassupplypiping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at test

pressuresequaltoorlessthan1/2psi(3.5kPa).

Checkalllocalcodesforrequirements,especiallyforthesizeand

type of gas supply line required.

RECOMMENDED MINIMUM GAS PIPE DIAMETER

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10feet

0-3meters

1/2in.

12.7mm

3/8in.

9.5mm

1/2in.

12.7mm

3/8in.

9.5mm

10-40feet

4-12meters

1/2in.

12.7mm

1/2in.

12.7mm

5/8in.

15.9mm

1/2in.

12.7mm

40-100feet

13-30meters

1/2in.

12.7mm

1/2in.

12.7mm

3/4in.

19mm

1/2in.

12.7mm

100-150feet

31-46meters

3/4in.

19mm

1/2in.

12.7mm

7/8in.

22.2mm

3/4in.

19mm

NOTICE:Checktoconrmwhetheryourlocalcodesallowplastic

or copper tubing for outdoor use.

NOTICE:Becausesomemunicipalitieshaveadditionallocalcodes,

consult your local authority and installation code.

Installing a Manual Gas Shut-Off Valve

Eachrepitmusthave an accessiblemanualgasshut-offvalve

locatedinthevicinityoftheunit.Wherenoneexists,orwhereitssize

or location is not adequate, contact your local authorized installer

for installation or relocation.

Compoundsusedonthreadedjointsofgaspipingshallberesistant

totheactionofliqueedpetroleumgases.Thegaslinesmustbe

checkedforleaksbytheinstaller.Thisshouldbedonewithasoap

solutionwatchingforbubblesonallexposedconnections,andif

unexposed,apressuretestshouldbemade.Toavoiddamageto

thegaspiping,removealltestingsolutionwhentestingiscomplete.

WARNING

Never use an exposed ame to check for leaks. The repit

must be disconnected from piping at inlet of control valve

and pipe capped or plugged for pressure test. Never pressure

test with repit connected; control valve will sustain damage!

Agasvalveandgroundjointunionshouldbeinstalledinthegas

line upstream of the gas control to aid in servicing. It is required by

theNationalFuelGasCodethatadriplinebeinstallednearthe

gas inlet. This should consist of a vertical length of pipe connected

intothegaslinebyateetingwithacaponthebottominwhich

condensation and foreign particles may collect.

Theuseofthefollowinggasconnectorsisrecommended:

— ANSIZ21.24ApplianceConnectorsofCorrugatedMetalTubing

andFittings

— ANSI Z21.45 Assembled Flexible Appliance Connectors of

OtherThanAll-MetalConstruction

The above connectors may be used if acceptable by the authority

havingjurisdictionTheCommonwealthofMassachusettsrequires

thataexibleapplianceconnectorcannotexceedthreefeetinlength.

LP GAS

SUPPLY

SHUT-OFF

VALVE

FLEX TUBING

MALE NPT to

MALE FLARE

VALVE

MALE NPT to

MALE FLARE

LP GAS

SUPPLY

FEMALE NPT to

FEMALE NPT

LP GAS SUPPLY

NATURAL

GAS SUPPLY

SHUT

-OFF

LVE

FLEX TUBING

MALE NPT to

MALE FLARE

REGULATOR

NIPPLE

NATURAL

GAS SUPPLY

MALE NPT to

MALE FLARE

VALVE

FEMALE NPT to

FEMALE NPT

NAT GAS SUPPLY

Figure 18

NOTICE: Gasshut-offvalveshown.Othervalvesapprovedto

usewithgasallowed.

Flextubingtovalveispre-installedatthefactory.Flareconnector

islooselyinstalledforshippingpurposesonly.Anaccessible

manualgasshut-offvalvemustbeinstalledexternaltotherepit.

GASSUPPLY

PROPANEGASSUPPLY

NATURALGASSUPPLY

37795-3-0119 Page 15

WARNING

If these instructions are not precisely followed, a re may

occur causing death or serious injury.

Propane Cylinder Specications

Thisrepitreplacecanbeusedwithanon-disposableself-con-

tainedPropaneGassupplysystem:

• Propanecylindersmaybeacceptableforusewiththe

replaceprovidedtheyarecompatiblewiththerepit

retention means.

• PropaneGassupplycylindermustbeconstructedand

markedinaccordancewiththeU.S. Department of

Transportation (D.O.T.) Specications for Propane Gas

Cylinders, or the Standard for Cylinders, Spheres and

Tubes for Transportation of Dangerous Goods and Com-

mission, CAN/CSA-B339 as applicable.

• PropaneGassupplycylindersbetween4and40

poundsmusthaveanoverllpreventiondevice.

• PropaneGassupplycylindermusthaveaconnection

devicecompatiblewiththeconnectionoftherepit.

• IftherepitisequippedwithaCGANo.600Cylinder

ConnectionDevice,thecylindermustbedisconnected

whentherepitisnotinuse.

• Iftherepitistobepermanentlyconnectedtoagaspip-

ingsystemfromaremotesupplytank,installationmust

beinaccordancewithlocalcodesor,intheabsence

oflocalcodes,withtheNational Fuel Gas Codes ANSI

Z223.1/NFPA 54.

• Adentedorrustycylindermaybehazardousandshould

becheckedbyyourpropanesupplier.Neveruseacylin-

derwithadamagedvalve.

• TheOL48TP(10,18)Prepitmaybeconnectedtoa20

lb.(9.1kg)sizepropanecylinderonly.(Notsupplied)

• TheOL60TP(10,18)Prepitmaybeusedwitha20lb.

(9.1kg)or30lb.(13.6kg)sizepropanecylinderonly

(notsupplied).

• Thepropanecylindermustbeprovidedwithashut-

off valve terminating in a propane cylinder valve type

QCC1,andasafetyreliefdevicehavingdirectcommu-

nicationwiththevaporspaceofthecylinder.

• The cylinder supply system must be arranged for vapor

withdrawalandthecylindershallincludeacollarto

protect the cylinder valve.

• ThePropaneGascylindermustbeprovidedwitha

listedoverllprotectiondevice(OPD).Neverllthe

cylinder beyond 80 percent full.

• DonotstoreasparePropaneGascylinderunderor

nearthisrepit.

• Useonlyapressureregulatorandhoseassemblythat

suppliesapressureof11in.watercolumntotherepit

andhasaQCC1typetting.

• Cylinderstobeusedwiththisunitmustbesuppliedwith

aQCC1cylindervalve.AQCC1cylinderhasapositive

seatingconnection,whichwillnotallowgasowuntil

a positive seal has been achieved. It is also equipped

withanexcessowdevice.Inordertoattainfullowto

therepit,thevalvemustbeintheoffpositionwhenthe

cylinder valve is turned on.

WARNING

A re will result if the gas supply hose makes contact with

the underside of the replace.

Propane Gas

Attachacylinderretainingbracket(notsupplied)tothebaseof

thecylinder.Thensecuretothesurfacetowhichitsits.Cylinder

should be on a level surface.

Cylinder Retaining Bracket

1. Fastenthebrackettothebottomofthepropanebottleusing

boltandnut(notsupplied).

2. Tightenthelagscrewintothemountingsurfaceleavingap-

proximately1/4in.ofthreadabovethesurface.

3. Slidepropanebottleintopositionsothatthebracketslides

undertheheadofthelagscrew.

4. Tightenthelagscrewontothebracket.

5. Forfasteningtoaconcretesurfaceaconcreteanchorwillbe

required.(Notsupplied)

Cylinder Connection:Ensurethegasregulatorhoseiskink

free. Remove the cap or plug from the cylinder fuel valve. Insert

theblackQCC1regulatornippleontotheQCC1fuelvalve.Hand

tightenclockwise.Donotusetools.Leaktestalljointspriorto

usingtherepit.Aleaktestmustbeperformedannuallyand

eachtimeacylinderishookeduporifapartofthegassystem

isreplaced.Ifthisrepitistobeconnecteddirectlytoahouse

propanegassupplyline,followtheinstructionsforthenatural

gashook-up.

Safety Considerations

• Makesurecylindervalveisinitsfulloffposition.(Turnclock-

wisetostop).

• Checkcylindervalvefeaturestoensureithasproperex-

ternalmatingthreads.(CylinderValveMarked:USEWITH

TYPE1)

• Inspecthosefordamage.Neverattempttousedamagedor

pluggedequipment.SeeyourlocalPropaneGasDealerfor

repairs.

• When connecting regulator assembly to the cylinder valve,

handtightenblackQCC1nutclockwisetoapositivestop.

DONOTuseawrenchtotighten.Useofawrenchmaydam-

agethequickclosingcouplingnutandresultinahazardous

condition.

• Locatethehoseoutofpathwayswherepeoplemaytripover

itorinareaswherethehosemaybesubjecttoaccidental

damage.

• Opencylindervalvefully(counter-clockwise).Turntheshut

offvalveattheunitslowlytotheonpositionanduseasoapy

watersolutiontocheckallconnectionsforleaksasindicated

inthediagramsbeforeattemptingtolighttherepit.Ifaleak

isfound,turntankvalveoffanddonotusetherepituntil

repairs can be made.

FIREPIT INSTALLATION (CONT'D)

PROPANEGASCYLINDERINFORMATION

37795-3-0119Page 16

FIREPIT INSTALLATION (CONT'D)

PROPANEGASCYLINDERINFORMATION

Enclosures For Propane Gas Supply Systems

EnclosuresforPropaneGassupplycylindersshallbeventilated

byopeningsatthelevelofthecylindervalveandatoorlevel.

Theeffectivenessoftheopening(s)forpurposesofventilation

shallbedeterminedwiththePropaneGassupplycylinder(s)in

place.Thisshallbeaccomplishedbyoneofthefollowing.

a. One side of the enclosure shall be completely open; or

b. Foranenclosurehavingfoursides,atopandabottom:

1. Atleasttwoventilationopeningsatcylindervalvelevel

shallbeprovidedinthesidewall,equallysized,spaced

at180degrees(3.14rad),andunobstructed.Each

opening shall have a total free area of not less than

1/2sqinperpound(2.3sq.cm/kg)ofstoredfuelcapac-

ityandnotlessthanatotalfreeareaof10sqin(64.5

sq.cm).

2. Ventilationopening(s)shallbeprovidedatoorlevel

andshallhaveatotalfreeareaofnotlessthan1/2sqin

perpound(3.2sq.cm/kg)ofstoredfuelcapacityandnot

lessthanatotalfreeareaof10sqin(64.5sq.cm).If

ventilationopeningsatoorlevelareinasideall,there

shallbeatleasttwoopenings.Thebottomoftheopen-

ingsshallbeatoorlevelandtheupperedgenomore

than5in.(127mm)abovetheoor.Theopeningsshall

beequallysized,spacedat180degrees(3.14rad)and

unobstructed.

3. Every opening shall have minimum dimensions so as to

permittheentranceofa1/8in.(3.2mm)diameterrod.

4. Thereshallbeaminimumclearanceof2in.(51mm)

betweenthelowersurfaceoftheoorofthePropane

Gassupplycylinderenclosureandtheground.

• Cylinder valves shall be readily accessible for hand opera-

tion.Adoorontheenclosuretogainaccesstothecylinder

valvesisacceptable,provideditisnon-lockingandcanbe

openedwithouttheuseoftools.

• Thedesignofthereplaceshallbesuchthat(1)the

PropaneGassupplycylinder(s)canbeconnected,discon-

nected and the connections inspected and tested outside the

cylinderenclosure;and(2)thoseconnectionswhichcould

bedisturbedwheninstallingthecylinder(s)intheenclosure

canbeleaktestedinsidetheenclosure;

• Ventilationopeningsinsidewallsshallnotcommunicate

directlywithotherenclosuresoftherepit.

TheenclosureforthePropaneGascylindershallisolatethe

cylinder from the burner compartment to provide:

a. Shielding from heat radiation;

b. Aamebarrier;and

c. Protection from foreign material.

Be certain to mount the Propane Gas cylinder on a at

surface and restrain it using a cylinder retaining bracket to

prevent it from tipping.

NON-LOCKING

DOOR

OPENING B

OPENING A

5” MAX

P AND SIDE PARTITION

TO ISOLATE TANK FROM

FIREPIT

FIREPIT POSITIONED

ABOVE TANK ENCLOSURE

FIREPIT POSITIONED

BESIDE T

ANK ENCLOSURE

5” MAX

2” MIN

1” MAX

Figure 19

Cylinder

Size

Opening

Area A

Opening

Area B

Recommended

Dimension C

20lb

(9.1kg)

20 sq.in.

(130cm

)

10 sq.in.

(65cm

)

34 in.

(863mm)

30lb

(13.6kg)

30 sq.in.

(195cm

)

15 sq.in.

(100cm

)

34 in.

(863mm)

NOTICE: Thereshallbeaminimumclearanceof2in.(51mm)

betweenthelowersurfaceoftheoorofthePropaneGassupply

cylinder enclosure and the ground.

FIREPIT

2” MIN

ENCLOSURE

2” MINIMUM

REQUIRED ABOVE

GROUND LEVEL

SEE VENT

REQUIREMENTS

LP TANK

Figure 20

37795-3-0119 Page 17

FIREPIT INSTALLATION (CONT'D)

UNPACKING THE FIREPIT

CAUTION

When unpacking the repit use gloves to protect from

sharp edges.

Thecontentsincludetherepitunit,instructionpacket,hardware

package,andtwoburnerpropsupportswhicharelocatedunder

therepitforshippingpurposesonly.

ENCLOSURE CONTRUCTION

Therepitrequiresacustombuiltenclosureforsupport.

Combustibleornon-combustiblematerialscanbeused.Minimum

internal enclosure dimensions are provided. See Figure 21.

Figures 22 and 23 give basic ideas for enclosure construction.

NOTICE:Measurerepitdimensionsandverifyframingorother

support methods before enclosure construction begins.

OL48TP OL60TP

Internal Enclosure Dimensions (inches)

HeightA *7-1/2Min. *7-1/2Min.

WidthB 51-3/4Min.

52-1/2Max.

63-3/4Min.

64-1/2Max.

DepthC 22-5/8Min.

23-1/2Max.

22-5/8Min.

23-1/2Max.

*NOTICE:

Additionalheightwillberequired,ifthedrainpan

accessory is installed.

Figure 21 - Internal Enclosure Dimensions

Beforecompletingtheenclosureandinstallingrepit,provideapath

forwaterdrainageoutoftherepit.

Determineiftheoptionalaccessorydrainpanwillbeused.Ifthe

drainpanwillbeinstalled,followtheinstructionsprovidedwith

thedrainpankittoinstallitatthispoint.

INSTALLATION

1. Choose installation location.

2. Construct enclosure. See Figures 21, 22, and 23 for typical

construction options.

3. ProvideelectricalserviceifLED'sareincluded.

4. ProvideforgassupplyconnectionsorPropanetankstorage.

5. IfinstallationincludesPropanetankstorageundertherepit,

usetheoptionalBRBVentKitorrefertothePropanetank

storage requirements on pages 15 and 16. See Figure 19.

BBA LP

TANK DOOR KIT

(OPTION)

BRB VENT KIT

REQUIRED OR

REFER TO LP

TANK ST

ORAGE

REQUIREMENT

ENCLOSURE VENTING REQUIREMENTS

FOR LP TANK STORAGE UNDER FIREPIT

Figure 22

6. Thephotographbelowshowsatypicalrepitinstallationfor

reference only. See Figure 23.

Figure 23

FIREPITENCLOSUREREQUIREMENTS

37795-3-0119Page 18

7. To connect the gas line and install the electrical connection,

theburnerassemblymustbetiltedupwardintherepit.

a Remove the control door by opening the door and lifting

thedoorupwardtodisengagetheslotsontheendsof

the door from the pivot bolts.

b. Removethe(4)llerstrips(IndexNo.'s31and32

illustratedonpage29),bysimplyliftingthemupfrom

the burner tray.

c. Removethetwocontroldoorpivotboltsusinga1/8-inch

hexallenwrench.See Figure 24.

Figure 24

d. Usinggloves,removethetwoexpandedmetalburner

cover screens from the burner tray, then set aside.

e. Removetwoscrewsfromfrontcornersofthecontrol

panelwitha5/16-inchhexheaddriver.See Figure 25.

REMOVE (2) HEX

HEAD SCREWS

Figure 25

f. Liftfrontofburnerassemblyandtiltupwardsandtoward

thebackoftherepit.Retrievethetwoproptoolsand

place one each side against the front corners of the

cabinet bottom and under the front corners of the control

panel. See Figure 26.

NOTICE:

Usecarewhenraisingtheburnertrayassembly

toavoidscratchingthestainlessinterioroftherepit.

NOTICE:

Proptoolsarelocatedundertherepitfor

shipping purposes only.

PROP TOOLS

Figure 26

8. Installgasandelectricalsuppliestorepit.Seepage14for

gas supply requirements. See page 13 for electrical sup-

plyrequirements.FormodelswithLEDlights,besureto

plugthetransformerpowercordplugintothejunctionbox

receptacle. See Figure 17.Foreaseofinstallation,thegas

and electrical supply are located on the valve side of the

repit.Bothmayberelocatedtoentertheoppositesideof

therepit.

9. Removeplasticprotectivelmfromtherepitoutertop,

controldoor,andllertrimpieces.

FIREPIT INSTALLATION (CONT'D)

FIREPITENCLOSUREREQUIREMENTS

37795-3-0119 Page 19

FIREPIT INSTALLATION (CONT'D)

FINISHING

Aftergasandelectricalhookupiscompleted,lowerandsecure

theburnerassembly(leavetwoproptoolsinbottomofrepit

forfutureuse)withthetwoscrewsremovedinFigure 25.

Installthe(4)llerstrips.Placethetwoshortsidellerstrips

inrst,theninstallthelongfrontandrearllerstrips.Thelong

llerstripswillinterlockattheendswiththesidellerstrips.

See Figure 27a.

INSTALL END

FILLER STRIPS

BEFORE THE LONG

FILLER STRIPS

END

FILLER

STRIP

LONG

FILLER

STRIP

Figure 27a

3. Ifinstallingtheoptionalglasswindpanelkit,donotinstall

thellerstripsinstep2.RefertoFigure 27bforglasswind

panelkitinstallation.

1 1/2”

min

Figure 27b

4. Reinstall the pivot bolts removed in Figure 24 and reinstall the

control door.

5. UnscrewtheignitorbuttonandinstalltheAAbatteryprovidedin

theinstructionenvelopepriortoclosingthecontroldoor.(Note

BatteryPolarity)See Figure 28.

Figure 28

6. Usinggloves,replacethetwoexpandedmetalscreens

removed in Step 7.

7. Afterallgasconnectionsandelectricalhook-ups(ifapplicable)

havebeenmade,checkforproperlightingoftheburner,and

LEDlightoperation(ifapplicable).Refertothelightingand

operation instructions on pages 21 to 23.

37795-3-0119Page 20

FIREPIT INSTALLATION (CONT'D)

FINISHING

Crushed Glass Installation

Ensure the burner cover screens are still properly installed,

fullycoveringtheLEDopenings.Placedecorativecrushed

glassevenlyovertheburnerandscreens(enoughmediato

coverapproximately7sq.ft.onOL48TP,or8sq.ft.onOL60TP

models).(Seepage6formediarequirements).Ensurecoverage

isevenandnotthickerinplaces.

NOTICE: Excessiveamountsofcrushed

glass placed over the burner, electrode,

or thermopile may cause various issues

including delayed lighting or sooting.

Somepiecesofbrokenglassmaybelargerthanothers.Itis

netousethesepieces,butnotovertheburneroramearea.

See Figure 29. Decorativeglassdropletsmaybeaddedasan

enhancement, but can not be used near or over the burner. See

Figure 30.Neitherglassnordropletsmaybeplacedoverthe

electrode.(Seepage6formediaaccessoriesandrequirements).

COVER ENTIRE BURNER AND SCREENED

AREAS WITH CRUSHED GLASS

SPREAD CRUSHED GLASS AWAY

FROM

DO NOT COVER

THERMOCOUPLE AND

ELECTRODE

Figure 29

IF DESIRED GLASS DROPLETS

MAYBE ADDED IN AREA SHOWN -

DO NOT USE DROPLETS

ON BURNER

Figure 30

La page charge ...

American Hearth OL48TP, OL60TP Le manuel du propriétaire

Marque: American Hearth

Modèle: OL48TP, OL60TP

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

Outdoor Linear Fire Pit (OL48TP, OL60TP)

Télécharger le PDF

rapport

dans d''autres langues

English: American Hearth OL48TP, OL60TP Owner's manual

American Hearth OL48TP, OL60TP Le manuel du propriétaire

Ce manuel convient également à

American Hearth OL48TP, OL60TP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents