LG LW1217ERSM Le manuel du propriétaire

LW1017ERSM

LW1217ERSM

EN ENGLISH

FR FRANÇAIS

TYPE: WINDOW

www.lg.com

OWNER’S MANUAL

AIR CONDITIONER

Read this owner’s manual thoroughly before operating the

appliance and keep it handy for reference at all times.

*MFL70960706*

MFL70960706

Rev.02_100720

2

TABLE OF CONTENTS

19 LG ThinQ Application

3 SAFETY INSTRUCTIONS

3 IMPORTANT SAFETY INSTRUCTIONS

8 PRODUCT OVERVIEW

8 Exterior Parts

8 Interior Parts

19 SMART FUNCTIONS

22 MAINTENANCE

22 Air Filter

23 TROUBLESHOOTING

23 Before Calling for Service

23 Normal Sounds You May Hear

27 WARRANTY

11 How to Install the Unit

11 Window Requirements

12 Preparation of Cabinet

13 Cabinet Installation

14 Unit Installation

16 OPERATION

16 Control Panel and Remote Control

17 Wireless Remote Control

18 Ventilation

18 Air Direction

18 Additional Features

9 INSTALLATION

9 Electrical Data

10 Parts Included

11 Storm Window Requirements

3 EN

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always

read and follow all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others.

All safety messages will follow the safety alert symbol and either the word WARNING or

CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce

the chance of injury, and tell you what may happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

injury to persons when using this product, follow basic precautions,

To reduce the risk of explosion, fire, death, electric shock, scalding or

including the following:

INSTALLATION

●Before use, the appliance must be properly installed as described in this manual.

●Contact the authorized service technician for repair or maintenance of this unit.

●Contact the installer for installation of this unit.

●The air conditioner is not intended for use by young children or invalids without supervision.

●Young children should be supervised to ensure that they do not play with the air conditioner.

The following symbols are displayed on units.

This symbol indicates that this appliance uses a flammable refrigerant. If the refrigerant is

is leaked and exposure to an external ignition source, there is a risk of fire.

This symbol indicates that the Operation Manual should be read carefully.

This symbol indicates that a service personnel should be handling this equipment with

reference to the Installation Manual.

This symbol indicates that information is available such as the Operating Manual or

Installation Manual.

4

SAFETY INSTRUCTIONS

●When the power cord is to be replaced, replacement work shall be performed by authorized

●Installation work must be performed in accordance with the National Electric Code by qualified

and authorized personnel only.

personnel only using only genuine replacement parts.

●Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

●Always plug into a grounded outlet.

●Do not under any circumstances, cut or remove the third (ground) prong from the power cord.

●When installing or moving the appliance, be careful not to pinch, crush, or damage the power

cord.

●Plug in the power plug properly.

●Do not modify or extend the power cord.

●Do not start/stop operation by plugging/unplugging the power cord.

●If the cord/plug is damaged, have it replaced by an authorized service person using authorized

replacement parts.

●Use a dedicated circuit.

●Do not disassemble or modify the product.

●Adhere to all industry recommended safety procedures including the use of long-sleeved gloves

and safety glasses.

●Use care when unpacking and installing. The edges of the product may be sharp.

●Disconnect the power cord or circuit breaker before installing or servicing the appliance.

●Keep packaging materials out of the reach of children. These materials can pose a suffocation

risk to children.

●Store and install the product where it will not be exposed to temperatures below freezing or

●Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

exposed to outdoor weather conditions.

OPERATION

●Use this appliance only for its intended purpose.

●Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a damaged cord or plug.

●Repair or immediately replace all power cords that have become frayed or otherwise damaged.

Do not use a cord that shows cracks or abrasion damage along its length or at either end.

●Do not run cord under carpets or mats where it could be stepped on and damaged.

●Keep the cord out from under heavy objects like tables or chairs.

●Do not place the power cord near a heat source.

●Do not use an adaptor or plug the product into a shared outlet.

●Do not tamper with controls.

●If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance,

●Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull

straight out from the outlet.

unplug it immediately, and contact an LG Electronics Customer Information Center.

●Do not grasp the power cord or touch the appliance controls with wet hands.

5 EN

SAFETY INSTRUCTIONS

●If water enters the product, turn off the power at the main circuit, then unplug the product and call

for service.

●If the product has been submerged, contact an LG Electronics Customer Information Center for

instructions before resuming use.

●Unplug the product when unused for long periods.

●Unplug the product before cleaning.

●In the event of a gas leak (propane gas, etc.) do not operate this or any other appliance. Open a

window or door to ventilate the area immediately.

●This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning the use of the appliance by a person responsible for

their safety.

●The interior of the product must only be cleaned by an authorized service center or a dealer.

●Do not use solvent-based detergent on the product. Doing so can cause corrosion or damage,

product failure, electrical shock, or fire.

GROUNDING INSTRUCTIONS

●The power cord of this appliance is equipped with a three-prong (grounding) plug. Use this with

a standard three-slot (grounding) wall power outlet to minimize the hazard of electric shock. The

customer should have the wall receptacle and circuit checked by a qualified electrician to make

sure the receptacle is properly grounded. DO NOT CUT OR REMOVE THE THIRD (GROUND)

PRONG FROM THE POWER PLUG.

- Situations when the appliance will be disconnected occasionally; Because of potential safety

hazards, we strongly discourage the use of an adapter plug. However, if you wish to use an

adapter, a TEMPORARY CONNECTION may be made. Use UL-listed adapter, available from

most local hardware stores.

The large slot in the adapter must be aligned with the large slot in the receptacle to assure a

proper polarity connection.

●Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the

appliance unless the cover screw is metal, and not insulated, and the wall receptacle is grounded

through the house wiring. The customer should have the circuit checked by a qualified electrician

to make sure the receptacle is properly grounded.

●Disconnect the power cord from the adapter, using one hand on each. Otherwise, the adapter

ground terminal might break. Do not use the appliance with a broken adapter plug.

- Situations when the appliance will be disconnected often; Do not use an adapter plug in these

situations. Unplugging the power cord frequently can lead to an eventual breakage of the

ground terminal. The wall power outlet should be replaced by a three-slot (grounding) outlet

instead.

6

SAFETY INSTRUCTIONS

CAUTION

To reduce the risk of minor or moderate injury to persons, malfunction, or

damage to the product or property when using this product, follow basic

precautions, including the following:

INSTALLATION

●Take care when installing the product that exhaust or condensation does not damage nearby

property.

●Follow installation instructions exactly to avoid excessive vibration or water leakage.

OPERATION

●This appliance is not intended for use as a precision refrigeration system. Do not use it for special

purposes such as maintaining pets, food, precision machinery, or art objects.

●When installing or moving the appliance, be careful not to pinch, crush, or damage the power

cord.

●Make sure the air inlet and outlet are free from obstructions.

●Use a soft cloth to clean the appliance. Do not use waxes, thinners, or harsh detergents.

●Do not step on or place heavy objects on top of the appliance.

●Do not operate the appliance without the filter securely installed.

●Do not drink water drained from the appliance.

●Be sure to ventilate sufficiently when the air conditioner and a heating appliance such as a heater

are used simultaneously.

●Remove the batteries if the remote control is not to be used for an extended period of time.

●Never mix different types of batteries, or old and new batteries for the remote control.

●Stop using the remote control if there is a fluid leak in the battery. If your clothes or skin are

exposed to the leaking battery fluid, wash off with clean water

●If the leaking battery fluid has been swallowed, rinse the inside of the mouth thoroughly and

consult a doctor.

●Do not recharge or disassemble the batteries.

●Clean the filter every two weeks.

●Never touch the metal parts of the air conditioner when removing the air filter.

MAINTENANCE

●Never use strong cleaning agents or solvents when cleaning the air conditioner or spray water.

Use a smooth cloth.

Do not expose people, animals, or plants to the cold or hot wind from the air conditioner for

extended periods of time.

7 EN

SAFETY INSTRUCTIONS

REFRIGERANT (FOR R32 ONLY)

WARNING

●Do not use means to accelerate the defrosting process or to clean, other than those

recommended by the manufacturer.

●

The appliance shall be stored in a room without continuously operating ignition sources (for

example: open flames, an operating gas appliance or an operating electric heater).

●

Do not pierce or burn. Be aware that flammable refrigerants may not contain an odor.

●

This unit contains flammable refrigerant and has special safety precautions not normally

associated with older units. Please follow all precautions and advisories.

CAUTION

- Use caution while handling and prevent damage to unit. Do not put any holes into product for

any reason. This can cause damage to product and prevent unit from cooling.

- Maintenance and cleaning of unit should be performed by trained personnel. Failure to properly

Service should only be performed by technicians properly trained and certified in the use of

flammable refrigerants. Any service performed by unauthorized servicers/individuals will void all

warranties.

clean unit can result in damage to the refrigeration system and or the electrical system.

-

Make certain that all the air circulation/ventilation openings are free from obstruction.

-

When storing the appliance, do not put in a room with any open flame appliances, such as gas

water heaters or furnaces. Also keep away from electric heaters. Damaged units should be

repaired before storage.

-

SAVE THESE INSTRUCTIONS

8

PRODUCT OVERVIEW

Exterior Parts Interior Parts

8

6

2

3

1

4

5

7

3

4

5

6

7

1

2

1

Evaporator

2

Air Guide

3

4

Brace

5

Compressor

6

Condenser

7

Base Pan

Power Cord

1

Control Panel

2

Remote Control

3

Air Filter

Vertical Air Deflector (Horizontal Louver)

Horizontal Air Deflector (Vertical Louver)

4

5

6

Front Grille

7

8

Cabinet

Air Outlet

9

INSTALLATION

Electrical Data

Power cord may include a current interrupter

device. TEST and RESET buttons are provided

on the plug case. The device should be tested on

TEST button

and then the RESET button. If the TEST button

does not trip or if the RESET button will not stay

engaged, discontinue use of the air conditioner

WARNING

●This appliance should be installed in

accordance with the National Electrical

Code.

●Use of extension cords could cause serious

injury or death.

Do not use an extension cord with this

window air conditioner.

-

Do not use surge protectors or multi-outlet

adapters with this window air conditioner.

-

●Never push the TEST button during

operation. Doing so can damage the plug.

Do not remove, modify, or immerse this

plug. If this device trips, the cause should

be corrected before further use.

-

CAUTION

●The conductors inside this cord are

surrounded by shields, which monitor

leakage current. These shields are not

grounded. Periodically examine the cord

for any damage. Do not use this product

in the event the shields become exposed.

Avoid shock hazard. This unit cannot be

user-serviced. Do not open the tamper-

resistant sealed portion. All warranties and

performance will be voided. This unit is not

intended to be used as an ON/OFF switch.

Use Wall Receptacle Power Supply

Use 15 A, time

delay fuse or 15 A,

circuit breaker.

Standard 120 V, 3-wire

grounding receptacle rated

15 A / 120 VAC / 60 Hz

for 120 V

EN

a periodic basis by first pressing the

and contact a qualified service technician.

10

INSTALLATION

Tools Needed

Phillips-head

screwdriver

Adjustable wrench

Tape measure Pencil

Parts Included (Appearance May Vary)

Level Gloves

Scissors or

Cutting knife

Type 'A' Screws

(14)

Type 'B' Screws

(3)

Type 'C' Screws

(5)

Bolts

(2)

Lock Nuts

(2)

Heatproof foam (2)

(Adhesive backed)

Right curtain

panel

Left curtain

panel

Foam strip

(Non-adhesive)

Foam-PE (2)

(Adhesive backed)

Frame guide (2)

Window locking

bracket

Sill support (2)

This unit is designed for installation in standard

double hung windows with actual opening widths

from 27" to 39" (686mm to 991mm).

The top and bottom window sashes must open

sufficiently to allow a clear vertical opening of 16"

(406mm) from the bottom of the upper sash to the

inside sill.

●

27" to 39"

16" (406mm) min

1

To prevent vibration and noise, make sure

the unit is installed securely and firmly.

4

Install the unit slightly tilted so the back is

slightly lower than the front (about 1/2"

(12.7mm)). This will force condensed water

to flow to the outside.

5

Install the unit with the bottom between

30"~60" (762mm~1524mm) above the floor

level.

2

Install the unit out of direct sunlight.

3

Fence

Awning

Heat

radiation

Cooled air

CAUTION

●

There should be no obstacles, such as a

fence or wall, within 20" (508mm) from the

back of the cabinet because it will prevent

heat radiation of the condenser.

Restriction of outside air will greatly reduce

the cooling efficiency of the air conditioner.

DO NOT cover or block any of the side and

top louvers. All side louvers of the cabinet

must remain exposed to the outside of the

structure and unobstructed.

●

This product is a window air conditioner.

As such, a standard single-hung or double-hung

window is required for proper installation.

Non-window installations, including using sleeves

or wall openings, and other installation methods

are not recommended.

1

2

If necessary, attach another 2" x 2"

(50.8mm x

50.8mm)

wood strip flush against the back of

the inner sill.

Windows that include a storm window frame

may prevent the air conditioner from tilting

down toward the outside to drain properly.

For proper drainage, attach a 2" x 2" (50.8mm x

50.8mm) piece of wood to the inner sill, trimmed

to a length which fits inside the window frame.

The top of the wood shim must be at least 1 1/4"

(38.1mm) higher than the top of the storm

window frame. Attach the wood securely to the

sill with nails or screws.

NOTE

●

All supporting parts should be secured to firm

wood, masonry, vinyl, fiberglass, or metal.

Storm Window Requirements

Window Requirements

How to Install the Unit

11 EN

INSTALLATION

About

Over

1/2″ (12.7mm)

20″ (508mm)

(762mm~1524mm)

30″~60″

(686mm to 991mm)

Indoors

Inner Sill

Nail or screw

Outer Sill

Storm

Window Frame

Wood Strip Mounted

on Top of Inner Sill

1 1/4” (38.1mm) higher

than storm window frame

Outdoors

12

INSTALLATION

4

5

Upper Panel Guide

Right Curtain Panel

Left Curtain Panel

Lower Panel

Guide

Insert the top and bottom rails of the curtain

panels into the upper and lower panel

guides.

CAUTION

The lower panel guides are easily broken.

Be careful with them when installing the

cabinet.

●

6

Fasten the curtain panels to the unit with 8

type A screws.

Fasten the screws behind the curtain panel.

Preparation of Cabinet

1

Remove 4 screws which fasten the cabinet

at both sides and at the back. (Keep the

screws for later use.)

Shipping

Screws

CAUTION

●The unit is heavy. To prevent injury, use

proper lifting techniques when pulling unit

forward from cabinet. Obtain assistance

from another person if possible.

3

Cut the window sash seals (Foam-PE)

to the proper length. Peel off the backing

and attach the adhesive-backed foam to

the underside of the window sash and the

bottom of the window frame.

Foam-PE

(Adhesive backed)

2

Slide the unit from the cabinet by gripping

the base pan handle and pulling forward

while bracing the cabinet.

Insert the hooks on the lower panel guides

into the slots on the bottom of the cabinet.

Make sure that the flanges on the lower

panel guides will face toward the inside of

the room.

Hook

Indoor

Screws

(Type A)

Screws

(Type A)

NOTE

Use a long screwdriver to make installing

the screws easier.

●

13 EN

INSTALLATION

4

5

Install the cabinet with a slight tilt (about 1/2”

(12.7mm)) downward on the outside.

Use the bolt and nut to adjust the tilt of the

cabinet.

CAUTION

Do not drill a hole in the bottom pan.

The product is designed to operate with

approximately 1/2” (12.7mm) of water in the

bottom pan. There is no need to add water

if the pan is dry.

●

Screws (Type A)

Cabinet Track Holes

Indoor

Outdoor

about 1/2”

(12.7mm)

Cabinet

3

Loosely assemble each sill support.

Sill Support

Nut

Bolt

If the distance to the outer window sill is

not that deep, you may not need the bolt

and nut.

NOTE

●

Cabinet Installation

1

Open the window. Mark a line on the center

of the inside sill.

Carefully place the cabinet in the window and

align the center hole on the cabinet bottom

front with the center line on the sill.

2

Pull the bottom window sash down behind

the upper guide until It meets the cabinet.

Center Line

Outside Sill

Inside Sill

Center Hole

Inside Sill

Upper Panel

Guide

Window Sash

Do not pull the window sash down so

tightly that the movement of the curtain

panels is restricted.

NOTE

●

Use 2 type A screws to attach a sill support

to the cabinet track holes on one side. Use

the cabinet track holes that will place the sill

support nearest to the outer edge of the sill.

The longer side of the sill support should be

facing outside the window.

Repeat with the second sill support on the

opposite side of the cabinet.

14

INSTALLATION

2

Cut the non-adhesive foam strip to the

proper length and insert it between the

upper window sash and the lower window

sash.

Foam Strip

(Non-adhesive)

3

Window Locking Bracket

CAUTION

●

The unit is heavy. Use an assistant to help lift the

unit and set it in place. Lifting and maneuvering

the unit by yourself could result in injury.

●

Hold the unit firmly in place until the window

frame is lowered to meet the top surface of the

unit directly behind the upper guide. If the unit

falls from the window, it could cause personal

injury or property damage.

8

7

Pull each curtain panel out until it meets the

window sash track.

Front Angle

Sash Track

Upper Panel

Guide

Inside Window Sill

6

Sash Track

Front Angle

Screws (Type B)

Mount the cabinet to the window sill using

3 type B screws in the holes on the front

angle.

Screws

(Type C)

Screw

(Type C)

Screw

(Type C)

To prevent broken glass or damage to

windows, on vinyl or other similarly

constructed windows, attach the window

locking bracket with a type C screw.

Vinyl

Wood

1

Unit Installation

With the aid of an assistant, slide the unit

into the cabinet. Do not push on the

controls or the finned coils. Reinstall the

screws removed from the cabinet sides in

step 1 of preparation of cabinet.

Use a screwdriver or power drill to attach

the curtain panels to the window sashes

by inserting 4 type C screws into the

sashes through the panel holes shown in

the figure below.

15 EN

INSTALLATION

5

6

NOTE

Guide the lever carefully through the grille

as you push it in.

●

NOTE

●

See the Electrical Data section for

information on attaching the power cord

to an electrical outlet.

●

Heatproof Foam

H

Heatproof foam improves the cooling

capability of the air conditioner.

4

Before installing the front grille, fold out the

vent control lever located to the left

of the control panel, as shown below.

W1

(Adhesive Backed)

W2

Connect the wire harness before

assembling the front grille.

Attach the front grille to the cabinet by

inserting the tabs on the grille into the

slots on the front top of the cabinet.

Push the grille in until it snaps into place.

Insert 2 type A screws through the front

grille.

8

After the air conditioner is installed,

measure the curtain panel on each side

and cut the adhesive-backed heatproof

foam to fit each panel. The size of the

panels may differ. Remove the backing

from the heatproof foam and attach the

foam to the curtain panels.

W1

W2

7

Remove air filter from the front grille by

pulling the filter forward and then up

slightly.

W

H

W

H

16

OPERATION

Control Panel and Remote Control

Remote Control

5

Wi-Fi (Wi-Fi Model Only)

Enables connection of the air conditioner to

the home Wi-Fi.

1

Power

Press to turn the air conditioner ON or OFF.

2

Fan Speed

Press to set the fan speed to Low (F1),

Medium (F2), or High (F3).

3

Delay ON/OFF Timer

Delay ON - When the air conditioner is off,

set it to automatically turn on from 1 to 24

hours later, at its previous mode and fan

settings.

Delay OFF - When the air conditioner is on,

set it to automatically turn off from 1 to 24

hours later.

NOTE

●Each press of the Timer button advances

the timer by 1 hour. After the last press

the display returns to the temperature

setting.

4

Operation Mode

Press the Mode button to cycle between

4 types of air conditioner operation:

Energy Saver / Cool / Fan / Dry.

Cool

Fan - In this mode the fan circulates air

but the compressor does not run. Use

the Fan Speed button to set fan speed to

High, Medium or Low. In this mode, you

cannot adjust the set temperature.

Dry - This mode is ideal for rainy and

damp days to dehumidify the room rather

than cooling it significantly. Humidity is

removed from the room by the combination

of compressor operation and the fan speed

fixed at Low. The compressor and fan turn

off once the set temperature is reached.

Fan speed cannot be adjusted in Dry mode.

1

4

2

7

3

- This mode is ideal on hot days to

cool and dehumidify the room quickly. Use

the Temp

buttons to set the desired

room temperature and use the Fan Speed

button to set the desired fan circulation

speed.

Energy Saver - In this mode the

compressor and fan turn off when the set

temperature is achieved. Approximately

every 3 minutes the fan turns on to allow

the unit sensor to accurately determine if

more cooling is needed.

●The feature may be changed according to the type of model.

4 3 2

1

7

65

17 EN

OPERATION

6

7

Temperature Control

The thermostat monitors room temperature

to maintain the desired temperature. The

thermostat can be set between 60 °F–86 °F

(16 °C–30 °C). Press

or arrows to

increase or decrease temperature setting.

NOTE

●Auto Restart: If the air conditioner turns off due

to a power outage, it will restart automatically

once the power is restored, with the same

settings as were set before the unit turned off.

●Energy Saver: The unit defaults to the Energy

Saver mode each time the unit is switched on

except in Fan mode or when power is restored

after an electrical power outage.

●The remote control will not function properly if

the AC infrared sensor is exposed to direct light

or if there are obstacles between the remote

control and the air conditioner.

Wireless Remote Control

Inserting Battery

1

Push out the cover on the back of the

remote control with your thumb.

2

With the plus and minus poles facing as

marked, insert one new AAA 1.5 V

battery.

3

Reattach the cover.

NOTE

●One new battery is supplied with the air

conditioner for use in the remote control.

●Do not use a rechargeable battery. Make sure

that the battery is new.

●In order to prevent discharge, remove the

battery from the remote control if the air

conditioner is not going to be used for an

extended period of time.

●Keep the remote control away from extremely

hot or humid places.

●To maintain optimal operation of the remote

control, the remote sensor should not be

exposed to direct sunlight.

Clean Filter

The Clean Filter LED lights up to notify you

that the filter needs to be cleaned. After

cleaning the filter, press

Temp

and

together on the control panel to turn off the

Clean Filter light.

NOTE

●The filter reset must be done using the

control panel, not the remote control.

●This feature is a reminder to clean the air

filter for more efficient operation. The LED

light turns on after 250 hours of operation.

18

OPERATION

Close Open

Air Direction

Adjusting Horizontal Airflow

Direction

Adjusting Vertical Airflow

Direction

Ventilation

Push the ventilation lever in to the closed position

to maintain the best cooling performance. Pull

the ventilation lever out to open the vent and

draw fresh air into the room.

Airflow can be adjusted by changing the direction

of the air conditioner’s louvers.

The horizontal airflow is adjusted by moving the

levers of the vertical louvers to the left or right.

Touch the horizontal louvers to adjust the airflow

up or down.

NOTE

●When the weather is extremely hot, the unit

may turn off automatically to protect the

compressor.

Additional Features

Slinger Fan

This air conditioner is equipped with a slinger

fan. (See drawing.)

The fan’s outer ring picks up the condensed

water from the base pan if the water level gets

high enough. The water is then picked up by the

fan and expelled through the condenser, making

Ring

the air conditioner more efficient.

SMART FUNCTIONS

The LG ThinQ application allows you to

communicate with the appliance using a

smartphone.

Communicate with the appliance from a

smartphone using the convenient smart features.

the or ThinQ logo

1

Check the distance between the appliance

and the wireless router (Wi-Fi network).

• If the distance between the appliance and

the wireless router is too far, the signal

strength becomes weak. It may take a

long time to register or installation may

fail.

2

Turn off the Mobile data or Cellular Data

on your smartphone.

3

Connect your smartphone to the wireless

router.

NOTE

• To verify the Wi-Fi connection, check that

icon on the control panel is lit.

• The appliance supports 2.4 GHz Wi-Fi

networks only. To check your network

frequency, contact your Internet service

provider or refer to your wireless router

manual.

• LG ThinQ is not responsible for any network

connection problems or any faults,

malfunctions, or errors caused by network

connection.

• If the appliance is having trouble connecting to

the Wi-Fi network, it may be too far from the

router. Purchase a Wi-Fi repeater (range

extender) to improve the Wi-Fi signal strength.

• The Wi-Fi connection may not connect or may

be interrupted because of the home network

environment.

• The network connection may not work

properly depending on the Internet service

provider.

• The surrounding wireless environment can

make the wireless network service run slowly.

• The appliance cannot be registered due to

problems with the wireless signal

transmission. Unplug the appliance and wait

about a minute before trying again.

• If the firewall on your wireless router is

enabled, disable the firewall or add an

exception to it.

• The wireless network name (SSID) should be

a combination of English letters and numbers.

(Do not use special characters.)

• Smartphone user interface (UI) may vary

depending on the mobile operating system

(OS) and the

manufacturer.

• If the security protocol of the router is set to

WEP, you may fail to set up the network.

Please change it to other security protocols

(WPA2 is recommended) and register the

product again.

LG ThinQ Application

This feature is only available on models with

LG ThinQ Application Features

If you experience a problem while using the

appliance,this smart diagnosis feature will help

you diagnose the problem.

Smart Diagnosis

Allows you to set various options on the

appliance and in the application.

Settings

Before Using LG ThinQ Application

TM

NOTE

• If you change your wireless router, internet

service provider, or password, delete the

registered appliance from the LG ThinQ

application and register it again.

• The application is subject to change for

appliance improvement purposes without

notice to users.

• Functions may vary by model.

SMART FUNCTIONS

19 EN

Installing the LG ThinQ

Application

Search for the LG ThinQ application from

the Google Play Store or Apple App Store on a

smartphone. Follow instructions to download

and install the application.

Open Source Software Notice

Information

To obtain the source code under GPL, LGPL, MPL,

and other open source licenses, that is contained

in this product, please visit http://opensource.lge.

com.

In addition to the source code, all referred license

terms, warranty disclaimers and copyright notices

are available for download.

LG Electronics will also provide open source code

to you on CD-ROM for a charge covering the cost

of performing such distribution (such as the cost of

media, shipping, and handling) upon email request

to [email protected]. This offer is valid for a

period of three years after our last shipment of this

product. This offer is valid to anyone in receipt of

this information.

Smart Diagnosis

This feature is only available on models with the

or logo.

Use this feature to help you diagnose and solve

problems with your appliance.

NOTE

TM

●

For reasons not attributable to LGE’s

negligence, the service may not operate due to

external factors such as, but not limited to, Wi-Fi

unavailability, Wi-Fi disconnection, local app

store policy, or app unavailability.

●

The feature may be subject to change without

prior notice and may have a different form

depending on where you are located.

Using LG ThinQ to Diagnose

Issues

If you experience a problem with your Wi-Fi

equipped appliance, it can transmit troubleshooting

data to a smartphone using the LG ThinQ

application.

●

Launch the LG ThinQ application and select

the Smart Diagnosis feature in the menu.

Follow the instructions provided in the LG

Thi

nQ application.

TM

20

SMART FUNCTIONS

La page charge ...

LG LW1217ERSM Le manuel du propriétaire

LG LW1217ERSM Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents