Wacker Neuson RD16-90 Manuel utilisateur

5000185429

06 1011

Operator’s Manual

Manual d'utilisation

Ride-On Roller

Rouleau

RD 16

EN/FR

5000185429

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000185405 05 1011

RD 16 Foreword

wc_tx001346gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Machine Item Number

RD 16 0620060

0620402

0620798

0620799

RD 16 IRH 0620127

Foreword RD 16

4 wc_tx001346gb.fm

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity

2011-CE-RD16-en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

RD 16-90, RD 16 IRH-90, RD 16-100

Ride-On Roller

To compact asphalt

0620799, 0620127, 0620798

16,8 kW

105 dB(A)

106 dB(A)

Conformity Assessment Procedure

According to ANNEX VIII

Notified Body

Lloyds Register Quality Assurance Limited (Notified Body No 0088)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Guidelines and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following guidelines and standards:

2006/42/EC, 2000/14/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 06.07.11

William Lahner

Vice President of Engineering

Paul Sina

Manager, Product Engineering

RD 16 Table of Contents

wc_bo5000185405_06TOC.fm 7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 11

1.1 Signal Words found in this Manual ..................................................... 11

1.2 Machine Description and Intended Use ............................................. 12

1.3 Operating Safety ................................................................................ 14

1.4 Operator Safety while using Internal Combustion Engines ................ 16

1.5 Service Safety .................................................................................... 17

2 Labels 20

2.1 Label Locations .................................................................................. 20

2.2 Label Meanings .................................................................................. 21

3 Lifting and Transporting 28

3.1 Lifting the Machine ............................................................................. 28

3.2 Tying Down and Transporting the Machine ........................................ 29

3.3 Towing ................................................................................................ 30

4 Operation 33

4.1 Preparing the Machine for First Use ................................................... 33

4.2 Position of the Operator ..................................................................... 33

4.3 Operation and Service Locations ....................................................... 34

4.4 Control Panel ...................................................................................... 36

4.5 Foldable Roll Over Protection Structure (ROPS) ............................... 38

4.6 Rotating Beacon (if equipped) ............................................................ 39

4.7 Backup Alarm (if equipped) ................................................................ 40

4.8 Lighting Equipment (if equipped) ........................................................ 40

4.9 Seat Belt ............................................................................................. 41

4.10 Operator Presence System ................................................................ 42

4.11 Scraper Bars ...................................................................................... 43

4.12 Anti-Vandalism Protection and Machine Access ................................ 44

4.13 Articulation Joint Lockarm .................................................................. 45

4.14 Machine Stability ................................................................................ 46

4.15 Operation on Slopes ........................................................................... 48

Table of Contents RD 16

8 wc_bo5000185405_06TOC.fm

4.16 Recommended Fuel ............................................................................49

4.17 Refueling the Machine .........................................................................49

4.18 Before Starting ....................................................................................50

4.19 Starting ................................................................................................51

4.20 Stopping/Parking .................................................................................52

4.21 Parking Brake Button ..........................................................................53

4.22 Direction and Speed ............................................................................53

4.23 Transmission .......................................................................................54

4.24 Vibration ..............................................................................................55

4.25 Water Spray System ...........................................................................56

4.26 Emergency Shutdown Procedure ........................................................57

4.27 Battery Disconnect ..............................................................................58

4.28 Auxiliary Battery Positive Terminal ......................................................58

4.29 Panel Indicator Lights ..........................................................................60

4.30 Turn Signal/Hazard Lights (if equipped) ..............................................62

5 Maintenance 64

5.1 Engine Maintenance Schedule ............................................................64

5.2 Roller Maintenance Schedule .............................................................65

5.3 Safety-Related Spare Parts .................................................................67

5.4 Maintaining the Seat and the Seat Belt ...............................................71

5.5 Cleaning the Spray Bars .....................................................................72

5.6 Rear Frame Access .............................................................................73

5.7 Fuel Filter ............................................................................................74

5.8 Priming the Fuel System .....................................................................75

5.9 Battery .................................................................................................76

5.10 Cleaning the Water Filter .....................................................................77

5.11 Engine Oil and Filter ............................................................................80

5.12 Engine Air Cleaner .............................................................................82

5.13 Grease Fittings ....................................................................................83

5.14 Hydraulic System Cleanliness .............................................................84

5.15 Hydraulic Oil Requirements .................................................................86

5.16 Hydraulic Oil Level ..............................................................................87

5.17 Hydraulic Suction Strainer ...................................................................87

5.18 Changing the Hydraulic Oil & Filter .....................................................88

5.19 Bleeding the Hydraulic System ...........................................................88

5.20 Storage ................................................................................................89

5.21 Manually Releasing Parking Brake .....................................................90

5.22 Troubleshooting ...................................................................................92

RD 16 Table of Contents

wc_bo5000185405_06TOC.fm 9

6 Technical Data 93

6.1 Engine ................................................................................................ 93

6.2 Roller .................................................................................................. 94

6.3 Lubrication .......................................................................................... 94

6.4 Dimensions mm (in.) .......................................................................... 95

6.5 Sound Measurements ........................................................................ 96

6.6 Measurements of Operator Exposure to Vibration ............................. 96

6.7 Hydraulic Pressures ........................................................................... 97

7 AEM Safety Manual 99

8 Schematics 126

8.1 Hydraulic Schematic ......................................................................... 126

8.2 Hydraulic Schematic Components ................................................... 127

8.3 RD 16—Electrical Schematic ........................................................... 128

8.4 RD 16—Electrical Schematic Components ...................................... 129

8.5 RD 16 IRH—Electrical Schematic .................................................... 130

8.6 RD 16 IRH—Electrical Schematic Components ............................... 131

Table of Contents RD 16

10 wc_bo5000185405_06TOC.fm

RD 16 Safety Information

wc_si000399gb.fm 11

1 Safety Information

1.1 Signal Words found in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information RD 16

12 wc_si000399gb.fm

1.2 Machine Description and Intended Use

This machine is a dual drum, ride-on roller. The Wacker Neuson Ride-

On Roller consists of an articulated frame onto which is mounted a

gasoline or diesel engine, a fuel tank, a hydraulic tank, a water tank, a

hydrostatic drive system, two steel drums containing internal eccentric

weights, and an operator’s platform with a ROPS (Roll Over Protective

Structure). The engine powers the hydraulic systems that provide

machine movement and drum vibration. The vibrating drums smooth

and compact the work surface as the machine moves. Machine speed,

direction, and vibration are controlled by the operator from the

operator’s seat on the platform.

The machine is designed as a lightweight roller to be used in the

compaction of sublayers and finish layers of asphalt on roads,

driveways, parking lots, and other types of asphalt-covered surfaces.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to tow other machines

• Using the machine to spray liquids other than water (i.e., diesel

fuel on asphalt)

• Operating the machine outside of factory specifications.

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Burns from hot hydraulic fluid

• Fire hazards from improper refueling techniques

• Fuel and its fumes

RD 16 Safety Information

wc_si000399gb.fm 13

• Personal injury from improper lifting techniques

• Crushing hazards from improper operation (feet, legs, or arms

extending outside of the operator work station) and for other

persons in the work zone

• Line of sight blockage by the ROPS

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

Safety Information RD 16

14 wc_si000399gb.fm

1.3 Operating Safety

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

• children

• people impaired by alcohol or drugs

Contact Wacker Neuson for additional training if necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

• Do not operate a machine in need of service or repair.

Before starting

• ALWAYS disengage and stow the locking bar for the articulated

steering joint before operating the machine. The machine cannot

be steered when the locking bar is engaged.

Machine condition

• Do not operate the machine with unapproved accessories or

attachments.

• NEVER operate the machine with the fuel cap loose or missing.

• NEVER use or attempt to repair damaged safety belts or ROPS.

Replace only with Wacker Neuson spare parts.

• ALWAYS check that all controls are functioning properly

immediately after start-up! DO NOT operate the machine unless

all controls operate correctly.

• Always operate machine with all safety devices and guards in

place and in working order. Do not modify or defeat safety

devices. Do not operate machine if any safety devices or guards

are missing or inoperative.

RD 16 Safety Information

wc_si000399gb.fm 15

Operator position

• DO NOT attempt to start the machine when standing alongside it.

Only start the engine when seated in the driver's seat and with

the forward/reverse control in the neutral position.

• Always remain seated and wear the seat belt at all times while

operating the machine.

During operation

• Do not drive off curbs or other uneven surfaces that will result in

jarring impacts to the machine and operator.

• Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and

may cause burns.

• Never leave the machine running unattended.

• Stay clear of the articulated steering joint and the area between

the front and rear frames.

• Always keep hands, feet, and loose clothing away from moving

parts of the machine.

Work area awareness

• Do not use a cellphone or send text messages while operating

this machine.

• ALWAYS remain aware of changing positions and the movement

of other equipment and personnel on the job site.

• ALWAYS remain aware of changing surface conditions and use

extra care when operating over uneven ground, on hills, or over

soft or coarse material. The machine could shift or slide

unexpectedly.

• ALWAYS use caution when operating the machine near the

edges of pits, trenches or platforms. Check to be sure that ground

surface is stable enough to support the weight of the machine

with operator and that there is no danger of the roller sliding,

falling or tipping.

After use

• Store the machine properly when it is not being used. The

machine should be stored in a clean, dry location out of the reach

of children.

Safety Information RD 16

16 wc_si000399gb.fm

1.4 Operator Safety while using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

RD 16 Safety Information

wc_si000399gb.fm 17

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

Service training

Before servicing or maintaining the machine:

• Read and understand the instructions contained in all manuals

delivered with the machine.

• Familiarize yourself with the location and proper use of all

controls and safety devices.

• Only trained personnel shall troubleshoot or repair problems

occurring with the machine.

• Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

• Do not allow improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must

be familiar with the associated potential risks and hazards.

Before servicing

• Some service procedures require that the machine’s battery be

disconnected. To reduce the risk of personal injury, read and

understand the service procedures before performing any service

to the machine.

• All adjustments and repairs MUST be completed before

operation. Do not operate the machine with a known problem or

deficiency! All repairs and adjustments should be completed by a

qualified technician.

WARNING

Safety Information RD 16

18 wc_si000399gb.fm

• Do not stand under the machine while it is being hoisted or

moved.

• DO NOT get onto the machine while it is being hoisted or moved.

• ALWAYS turn engine off before servicing machine. If the engine

has electric start, disconnect negative terminal on battery.

• ALWAYS secure the articulated steering joint using the locking

bar before lifting, jacking, and servicing the machine. The

machine halves could swing together unexpectedly and cause a

serious injury.

• ALWAYS lock the lifting cylinders in the open position when the

seat pedestal is raised.

Work area awareness

• ALWAYS keep hands, feet and loose clothing away from moving

parts.

• ALWAYS make sure slings, chains, hooks, ramps, jacks, and

other types of lifting devices are attached securely and have

enough weight-bearing capacity to lift or hold the machine safely.

Always remain aware of the location of other people in the area

when lifting the machine.

While servicing

• Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

• Do not use gasoline or other types of fuels or flammable solvents

to clean parts, especially in enclosed areas. Fumes from fuels

and solvents can become explosive.

• Do not remove the radiator cap when the engine is running or

hot. The radiator fluid is hot and under pressure and may cause

severe burns!

• Do not open the hydraulic lines or loosen the hydraulic

connections while the engine is running! Hydraulic fluid under

pressure can penetrate the skin, cause burns, blind, or create

other personal injury hazards.

• Fluid leaks from small holes are often practically invisible. DO

NOT use your bare hands to check for leaks. Check for leaks

using a piece of cardboard or wood.

• DO NOT remove air cleaner cover, paper element, or precleaner

while engine is running.

RD 16 Safety Information

wc_si000399gb.fm 19

After servicing

• Always make sure hose connections have been reconnected

back to the correct fitting. Failure to do so may result in damage

to the machine and/or injury to person on or near the machine.

• Before you start the machine, ensure that all tools have been

removed from the machine and that replacement parts and

adjusters are firmly tightened.

• ALWAYS replace the safety devices and guards after repairs and

maintenance.

Maintaining machine condition

• Do not modify the machine without the express written approval

of the manufacturer.

• DO NOT modify, weld, or drill safety frames (ROPS) fitted as

original equipment. DO NOT loosen or remove bolts. DO NOT

weld, drill or modify a broken safety frame.

• ALWAYS check all external fasteners at regular intervals.

• Keep the machine clean and labels legible. Replace all missing

and hard-to-read labels. Labels provide important operating

instructions and warn of dangers and hazards.

• ALWAYS do periodic maintenance as recommended in the

Operator’s Manual.

• When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to

the original in all types of specifications, such as physical

dimensions, type, strength, and material.

Labels RD 16

20 wc_si000400gb.fm

2Labels

2.1 Label Locations

GG

FF

R

T

La page est en cours de chargement...

Wacker Neuson RD16-90 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson RD16-90 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents