Wacker Neuson RD16-100 Manuel utilisateur

0178395en 005 0310

0178395EN

Operator’s Manual

Ride-On Roller

RD 16

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker Neuson Corporation

represents an infringement of valid copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Corporation

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Translated

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

RD 16 Foreword

wc_tx001346gb.fm 3

Foreword

Machines covered in this manual

Machine

documentation

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson

Corporation to order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce

the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson Corporation expressly reserves the right to make technical

modifications, even without notice, which improve the performance or safety

standards of its machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson Corporation reserves the right

to change any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Machine Item Number

RD 16 0620060

0620402

0620798

0620799

RD 16 IRH 0620127

Foreword RD 16

4 wc_tx001346gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

RD 16 Table of Contents

wc_bo0178395en_005TOC.fm 5

Foreword 3

1 Safety Information 9

1.1 Signal Words found in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Operating Safety ................................................................................ 12

1.4 Operator Safety while using Internal Combustion Engines ................ 14

1.5 Service Safety .................................................................................... 15

2 Labels 18

2.1 Label Locations .................................................................................. 18

2.2 Safety Labels ...................................................................................... 19

2.3 Informational Labels ........................................................................... 25

3 Operation 28

3.1 Operation and Service Locations ....................................................... 28

3.2 Control Panel ...................................................................................... 30

3.3 Roll Over Protection Structure (ROPS) .............................................. 32

3.4 Foldable Roll Over Protection Structure (ROPS) (if equipped) .......... 33

3.5 Rotating Beacon (if equipped) ............................................................ 35

3.6 Backup Alarm (if equipped) ................................................................ 35

3.7 Lighting Equipment (if equipped) ........................................................ 36

3.8 Seat Belt ............................................................................................. 37

3.9 Operator Presence System ................................................................ 38

3.10 Scraper Bars ...................................................................................... 39

3.11 Anti-Vandalism Protection and Machine Access ................................ 40

3.12 Articulation Joint Lockarm .................................................................. 41

3.13 Machine Stability ................................................................................ 42

3.14 Operation on Slopes ........................................................................... 44

3.15 Recommended Fuel ........................................................................... 44

3.16 Position of the Operator ..................................................................... 45

3.17 Preparing the Machine for First Use ................................................... 45

3.18 Before Starting ................................................................................... 47

3.19 Starting ............................................................................................... 48

3.20 Stopping/Parking ................................................................................ 50

Table of Contents RD 16

6 wc_bo0178395en_005TOC.fm

3.21 Parking Brake Button ..........................................................................51

3.22 Direction and Speed ............................................................................52

3.23 Transmission .......................................................................................53

3.24 Vibration ..............................................................................................54

3.25 Water Spray System ...........................................................................55

3.26 Emergency Shutdown Procedure ........................................................56

3.27 Battery Disconnect ..............................................................................57

3.28 Auxiliary Battery Positive Terminal ......................................................57

3.29 Panel Indicator Lights ..........................................................................58

3.30 Turn Signal/Hazard Lights (if equipped) ..............................................60

4 Maintenance 62

4.1 Engine Maintenance Schedule ............................................................62

4.2 Roller Maintenance Schedule .............................................................63

4.3 Safety-Related Spare Parts .................................................................64

4.4 Maintaining the Seat and the Seat Belt ...............................................68

4.5 Cleaning the Spray Bars .....................................................................69

4.6 Rear Frame Access .............................................................................70

4.7 Fuel Filter ............................................................................................71

4.8 Priming the Fuel System .....................................................................71

4.9 Battery .................................................................................................72

4.10 Engine Oil and Filter ............................................................................74

4.11 Engine Air Cleaner ..............................................................................75

4.12 Grease Fittings ....................................................................................76

4.13 Hydraulic System Cleanliness .............................................................77

4.14 Hydraulic Oil Requirements .................................................................78

4.15 Hydraulic Oil Level ..............................................................................79

4.16 Hydraulic Suction Strainer ...................................................................79

4.17 Changing the Hydraulic Oil & Filter .....................................................80

4.18 Bleeding the Hydraulic System ...........................................................80

4.19 Lifting the Machine ..............................................................................81

4.20 Tying Down and Transporting the Machine .........................................82

4.21 Storage ................................................................................................83

4.22 Towing .................................................................................................84

4.23 Manually Releasing Parking Brake .....................................................86

4.24 Troubleshooting ...................................................................................88

RD 16 Table of Contents

wc_bo0178395en_005TOC.fm 7

5 Schematics 90

5.1 Hydraulic Schematic ........................................................................... 90

5.2 Hydraulic Schematic Components ..................................................... 91

5.3 Electrical Schematic—RD 16 ............................................................. 92

5.4 Electrical Schematic Components—RD 16 ........................................ 94

5.5 Electrical Schematic—RD 16 IRH ...................................................... 96

5.6 Electrical Schematic Components—RD 16 IRH ................................. 98

6 Technical Data 99

6.1 Engine ................................................................................................ 99

6.2 Roller ................................................................................................ 100

6.3 Dimensions mm (in.) ........................................................................ 101

6.4 Sound Measurements ...................................................................... 102

6.5 Measurements of Operator Exposure to Vibration ........................... 102

6.6 Hydraulic Pressures ......................................................................... 103

Table of Contents RD 16

8 wc_bo0178395en_005TOC.fm

RD 16 Safety Information

wc_si000399gb.fm 9

1 Safety Information

1.1 Signal Words found in this Manual

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all

safety messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

Safety Information RD 16

10 wc_si000399gb.fm

1.2 Machine Description and Intended Use

This machine is a dual drum, ride-on roller. The Wacker Neuson Ride-

On Roller consists of an articulated frame onto which is mounted a

gasoline or diesel engine, a fuel tank, a hydraulic tank, a water tank, a

hydrostatic drive system, two steel drums containing internal eccentric

weights, and an operator’s platform with a ROPS (Roll Over Protective

Structure). The engine powers the hydraulic systems that provide

machine movement and drum vibration. The vibrating drums smooth

and compact the work surface as the machine moves. Machine speed,

direction, and vibration are controlled by the operator from the

operator’s seat on the platform.

The machine is designed as a lightweight roller to be used in the

compaction of sublayers and finish layers of asphalt on roads,

driveways, parking lots, and other types of asphalt-covered surfaces.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to tow other machines

• Using the machine to spray liquids other than water (i.e., diesel

fuel on asphalt)

• Operating the machine outside of factory specifications.

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Burns from hot hydraulic fluid

• Fire hazards from improper refueling techniques

• Fuel and its fumes

RD 16 Safety Information

wc_si000399gb.fm 11

• Personal injury from improper lifting techniques

• Crushing hazards from improper operation (feet, legs, or arms

extending outside of the operator work station) and for other per-

sons in the work zone

• Line of sight blockage by the ROPS

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

Safety Information RD 16

12 wc_si000399gb.fm

1.3 Operating Safety

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

1.3.1 Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

• children

• people impaired by alcohol or drugs

1.3.2 Contact Wacker Neuson for additional training if necessary.

1.3.3 Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

1.3.4 Do not drive off curbs or other uneven surfaces that will result in jarring

impacts to the machine and operator.

1.3.5 DO NOT attempt to start the machine when standing alongside it. Only

start the engine when seated in the driver's seat and with the forward/

reverse control in the neutral position.

1.3.6 Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and may

cause burns.

1.3.7 Do not operate the machine with unapproved accessories or

attachments.

1.3.8 Never leave the machine running unattended.

1.3.9 NEVER operate the machine with the fuel cap loose or missing.

WARNING

RD 16 Safety Information

wc_si000399gb.fm 13

1.3.10 Stay clear of the articulated steering joint and the area between the

front and rear frames.

1.3.11 NEVER use or attempt to repair damaged safety belts or ROPS.

Replace only with Wacker Neuson spare parts.

1.3.12 ALWAYS disengage and stow the locking bar for the articulated

steering joint before operating the machine. The machine cannot be

steered when the locking bar is engaged.

1.3.13 ALWAYS check that all controls are functioning properly immediately

after start-up! DO NOT operate the machine unless all controls operate

correctly.

1.3.14 ALWAYS remain aware of changing positions and the movement of

other equipment and personnel on the job site.

1.3.15 Always remain seated and wear the seat belt at all times while

operating the machine.

1.3.16 ALWAYS remain aware of changing surface conditions and use extra

care when operating over uneven ground, on hills, or over soft or

coarse material. The machine could shift or slide unexpectedly.

1.3.17 ALWAYS use caution when operating the machine near the edges of

pits, trenches or platforms. Check to be sure that ground surface is

stable enough to support the weight of the machine with operator and

that there is no danger of the roller sliding, falling or tipping.

1.3.18 Always keep hands, feet, and loose clothing away from moving parts

of the machine.

1.3.19 Store the machine properly when it is not being used. The machine

should be stored in a clean, dry location out of the reach of children.

1.3.20 Always operate machine with all safety devices and guards in place

and in working order. Do not modify or defeat safety devices. Do not

operate machine if any safety devices or guards are missing or

inoperative.

1.3.21 Do not operate a machine in need of service or repair.

Do not use a cellphone or send text messages while operating this

machine.

Safety Information RD 16

14 wc_si000399gb.fm

1.4 Operator Safety while using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are

present or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

RD 16 Safety Information

wc_si000399gb.fm 15

• Do not refuel if the machine is positioned in a truck fitted with a

plastic bed liner. Static electricity can ignite the fuel or fuel

vapors.

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

1.5.1 Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

1.5.2 Service training

Before servicing or maintaining the machine:

• Read and understand the instructions contained in all manuals

delivered with the machine.

• Familiarize yourself with the location and proper use of all con-

trols and safety devices.

• Only trained personnel shall troubleshoot or repair problems

occurring with the machine.

• Contact Wacker Neuson Corporation for additional training if nec-

essary.

When servicing or maintaining this machine:

• Do not allow improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must

be familiar with the associated potential risks and hazards.

1.5.3 Some service procedures require that the machine’s battery be

disconnected. To reduce the risk of personal injury, read and

understand the service procedures before performing any service to

the machine.

WARNING

Safety Information RD 16

16 wc_si000399gb.fm

1.5.4 All adjustments and repairs MUST be completed before operation. Do

not operate the machine with a known problem or deficiency! All

repairs and adjustments should be completed by a qualified

technician.

1.5.5 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

1.5.6 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

1.5.7 Do not modify the machine without the express written approval of the

manufacturer.

1.5.8 Do not remove the radiator cap when the engine is running or hot. The

radiator fluid is hot and under pressure and may cause severe burns!

1.5.9 DO NOT stand under the machine while it is being hoisted or moved.

1.5.10 DO NOT get onto the machine while it is being hoisted or moved.

1.5.11 DO NOT modify, weld, or drill safety frames (ROPS) fitted as original

equipment. DO NOT loosen or remove bolts. DO NOT weld, drill or

modify a broken safety frame.

1.5.12 Do not open the hydraulic lines or loosen the hydraulic connections

while the engine is running! Hydraulic fluid under pressure can

penetrate the skin, cause burns, blind, or create other personal injury

hazards.

1.5.13 ALWAYS check all external fasteners at regular intervals.

1.5.14 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

1.5.15 ALWAYS do periodic maintenance as recommended in the Operator’s

Manual.

1.5.16 ALWAYS turn engine off before servicing machine. If the engine has

electric start, disconnect negative terminal on battery.

1.5.17 ALWAYS keep hands, feet and loose clothing away from moving parts.

1.5.18 ALWAYS make sure slings, chains, hooks, ramps, jacks, and other

types of lifting devices are attached securely and have enough weight-

bearing capacity to lift or hold the machine safely. Always remain

aware of the location of other people in the area when lifting the

machine.

1.5.19 Always make sure hose connections have been reconnected back to

the correct fitting. Failure to do so may result in damage to the machine

and/or injury to person on or near the machine.

1.5.20 ALWAYS secure the articulated steering joint using the locking bar

before lifting, jacking, and servicing the machine. The machine halves

could swing together unexpectedly and cause a serious injury.

RD 16 Safety Information

wc_si000399gb.fm 17

1.5.21 ALWAYS lock the lifting cylinders in the open position when the seat

pedestal is raised.

1.5.22 Before you start the machine, ensure that all tools have been removed

from the machine and that replacement parts and adjusters are firmly

tightened.

1.5.23 Fluid leaks from small holes are often practically invisible. DO NOT use

your bare hands to check for leaks. Check for leaks using a piece of

cardboard or wood.

1.5.24 DO NOT remove air cleaner cover, paper element, or precleaner while

engine is running.

1.5.25 ALWAYS replace the safety devices and guards after repairs and

maintenance.

1.5.26 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

Labels RD 16

18 wc_si000400gb.fm

2Labels

2.1 Label Locations

GG

FF

RD 16 Labels

wc_si000400gb.fm 19

2.2 Safety Labels

Ref. Label Meaning

A

WARNING!

Read and understand the supplied Operator’s

Manual before operating the machine. Failure to

do so increases the risk of injury to yourself and

others.

B

DANGER!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area unless adequate

ventilation, through such items as exhaust

fans or hoses, is provided.

 Read the Operator’s Manual.

 No sparks, flames, or burning objects near

the machine.

 Stop the engine before refueling.

Use only clean, filtered diesel fuel.

D

WARNING!

Pressurized contents. Do not open when hot!

E

CAUTION!

Read and understand the supplied Operator’s

Manual before operating this machine. Failure to

do so increases the risk of injury to yourself and

others.

Labels RD 16

20 wc_si000400gb.fm

F

WARNING!

Pinch point.

G

WARNING!

Hot surface!

J

NOTICE

Lifting point.

K

WARNING

To reduce the risk of hearing loss, always wear

hearing protection when operating this machine.

Ref. Label Meaning

La page charge ...

Wacker Neuson RD16-100 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson RD16-100 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents