Poulan Pro PR5020 Le manuel du propriétaire

Marque: Poulan Pro

Modèle: PR5020

Taper: Le manuel du propriétaire

a WARNING! Read and follow all Safety Rules and

Operating Instructions before using this product.

Failure to do so can result in serious injury.

Instruction Manual

PR5020

Quick-Start Guide

NOTE: Your product may differ slightly from the item shown.

Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of fresh seasonal

gasoline for a 50:1 mixture. Shake well. Pour into fuel tank.

CAUTION: Do not use alternate fuels such as ethanol blends above

10% by volume (E-15, E-85) or any methanol blended fuel.

Add bar and chain oil to oil tank

until full.

Make sure chain brake is locked by

pushing forward on handguard.

Slowly press primer (air purge) bulb

10 times.

Pull blue choke lever out fully.

Place right foot in rear handle as shown.

Using right hand, pull starter rope sharply

until machine attempts to start, or a maximum

of 5 times.

Push blue choke lever to half choke

position.

Pull starter rope until engine starts.

Allow engine to warm for 30 seconds.

Make sure chain brake is unlocked by

pulling back on handguard.

Squeeze throttle trigger to set normal

idle. Your chainsaw is now ready

for use.

Press red switch to STOP position

ZKHQ¿QLVKHGXVLQJVDZ

STARTING A WARM ENGINE

4 + 5 + 7 + 8

NOTE: If the product does not restart, the problem could be overheated

IXHO7R¿[WKLVSUREOHPWU\WKHIROORZLQJSURFHGXUH

1. Set the product in a cool area away from direct sunlight.

2. Allow the product to cool for at least 20 minutes.

3. Press primer (air purge) bulb repeatedly for 10-15 seconds.

4. Follow the cold starting procedure.

Repeat this procedure if the problem still exists.

NOTE: Always use fresh seasonal fuel and shorten operation time

during unseasonably warm weather.

IMPORTANT:

• Never let your saw chain come in contact with soil/dirt during

operation. This will completely dull your chain and will require

installation of a new chain.

• Check your chain tension prior to each time you start the chainsaw.

&KHFNWHQVLRQRQDQHZFKDLQDIWHUWKH¿UVWPLQXWHVRI

operation. See the manual for chain tensioning instructions.

LDAV50MC115817295 Rev. D 2019-01-23

SYMBOLS

This machine can be

dangerous! Careless or

improper use can cause

serious injury.

Please read the operator's

manual carefully and make

sure you understand the

instructions before using the

machine.

Always use:

 eye protection such as non-

fogging, vented goggles or

face screen

 an approved safety helmet

 sound barriers (ear plugs

RUPXIÀHUVWRSURWHFW\RXU

hearing

Never operate a chain saw

holding it with one hand only.

%RWKRIWKHRSHUDWRUƍVKDQGV

must be used to operate the

chain saw.

Contact of the guide bar

tip with any object must be

avoided.

0HDVXUHGPD[LPXPNLFNEDFN

value.

A-weighted sound pressure

OHYHODWPHWHUVIHHW

according to Australia NSW

“Protection of the Environment

2SHUDWLRQV1RLVH&RQWURO

5HJXODWLRQ´7KLVGDWDLV

VSHFL¿HGRQWKHODEHO

Noise emission to the

environment according to

the European Community’s

'LUHFWLYH7KLVGDWDLVVSHFL¿HG

in the TECHNICAL DATA

section and on the label.

This product is in accordance

with applicable EC directives.

This product is in accordance

with applicable EAC directives.

This product is in accordance

with the Australian

electromagnetic compatibility

(0&UHJXODWLRQV

Use unleaded gasoline and

WZRVWURNHRLOPL[HGDWDUDWLR

RI

JDVROLQHWRRLOUDWLR

&KDLQRLO¿OO

The engine is stopped by

switching the ignition off using

the stop switch.

Primer.

Choke control.

Chain brake.

Unlock chain brake.

Lock chain brake.

Chain brake:



QRWORFNHGOHIW

 ORFNHGULJKW

Chain direction of rotation.

Chain tensioner.

Other symbols/decals on the machine refer to special

FHUWL¿FDWLRQUHTXLUHPHQWVIRUFHUWDLQPDUNHWV

The Emissions Compliance Period referred to on the

Emission Compliance label indicates the number of

operating hours for which the engine has been shown

to meet Federal emissions requirements.

0DLQWHQDQFHUHSODFHPHQWRUUHSDLURIWKHHPLVVLRQ

control devices and system may be performed by any

nonroad engine repair establishment or individual.

:$51,1*7KHHQJLQHH[KDXVWIURPWKLVSURGXFW

contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive

harm.

KNOW YOUR MACHINE

5($'7+,6,16758&7,210$18$/$1'6$)(7<58/(6%()25(23(5$7,1*<285&+$,16$:

Compare the illustrations with your unit to familiarize yourself with the location of the various controls and

adjustments. Save this manual for future reference.

 Front Hand Guard/Chain Brake

 Front Handle

3. Starter Rope

4. ON/STOP Switch

 Choke/Fast Idle Lever

6. Chain

7. 0XIÀHU

 Guide Bar

9. Bar & Chain Oil Cap

Starter Housing

Fuel Cap

Primer Bulb

 Rear Handle

 Throttle Lockout

3. Cylinder Cover

4. Air Filter Cover

 Adjustment Screw

6. Cutters

7. Depth Gauge

 Drive Links

9. Direction of Travel

Throttle Trigger



&KDLQ$GMXVWPHQW7RRO%DU7RRO

Clutch Cover

Bar Nuts

Chain Catcher

SAFETY

a WARNING! Always disconnect spark plug

wire and place wire where it cannot contact

spark plug to prevent accidental starting

when setting up, transporting, adjusting

or making repairs except carburetor

adjustments.

INTRODUCTION

A chainsaw is a high-speed wood-cutting tool. Special

safety precautions must be observed to reduce the

risk of accidents.

Failure to follow all safety rules and precautions can

result in serious injury.

If situations occur which are not covered in this

manual, use care and good judgment. If you need

assistance, contact your authorized service dealer or

call customer support.

PLANNING AHEAD

 Read this manual carefully until you completely

understand and can follow all safety rules,

precautions, and operating instructions before

attempting to use the unit.

 Restrict the use of your saw to adult users who

understand and can follow safety rules, precautions,

and operating instructions found in this manual.

 Wear protective gear. Always use steel-toed safety

IRRWZHDUZLWKQRQVOLSVROHVVQXJ¿WWLQJFORWKLQJ

safety chaps; heavy-duty, non-slip gloves; eye

protection such as non-fogging, vented goggles

or face screen; an approved safety hard hat; and

VRXQGEDUULHUVHDUSOXJVRUPXIÀHUVWRSURWHFW\RXU

hearing. Regular users should have hearing checked

regularly as chainsaw noise can damage hearing.

Secure hair above shoulder length.

 Keep all parts of your body away from the chain

when the engine is running.

 Keep children, bystanders, and animals a minimum

RIPHWHUVIHHWDZD\IURPWKHZRUNDUHD'R

not allow other people or animals to be near the

chainsaw when starting or operating the chainsaw.

 Do not handle or operate a chainsaw when you are

fatigued, ill, or upset, or if you have taken alcohol,

drugs, or medication. You must be in good physical

condition and mentally alert. Chainsaw work is

strenuous. If you have any condition that might be

aggravated by strenuous work, check with your

doctor before operating a chainsaw.

 Carefully plan your sawing operation in advance.

Do not start cutting until you have a clear work

area, secure footing, and, if you are felling trees, a

planned retreat path.

OPERATING YOUR SAW

 Do not operate a chainsaw with one hand. Serious

injury to the operator, helpers, bystanders or any

combination of these persons may result from

one-handed operation. A chainsaw is intended for

two-handed use.

 Operate the chainsaw only in a well-ventilated

outdoor area.

 Do not operate saw from a ladder or in a tree.



0DNHVXUHWKHFKDLQZLOOQRWPDNHFRQWDFWZLWKDQ\

object while starting the engine. Never try to start the

saw when the guide bar is in a cut.

 Do not put pressure on the saw at the end of the

cut. Applying pressure can cause you to lose control

when the cut is completed.

 Stop the engine before setting the saw down.

 Do not operate a chainsaw that is damaged,

improperly adjusted, or not completely and securely

assembled. Always replace bar, chain, hand guard,

or chain brake immediately if it becomes damaged,

broken or is otherwise removed.



([SRVXUHWRYLEUDWLRQVWKURXJKSURORQJHGXVHRI

gasoline powered hand tools could cause blood

YHVVHORUQHUYHGDPDJHLQWKH¿QJHUVKDQGV

and joints of people prone to circulation disorders

or abnormal swellings. Prolonged use in cold

weather has been linked to blood vessel damage

in otherwise healthy people. If symptoms occur

such as numbness, pain, loss of strength, change

LQVNLQFRORURUWH[WXUHRUORVVRIIHHOLQJLQWKH

¿QJHUVKDQGVRUMRLQWVGLVFRQWLQXHWKHXVHRIWKLV

tool and seek medical attention. An anti-vibration

system does not guarantee the avoidance of these

problems. Users who operate power tools on a

continual and regular basis must monitor closely

their physical condition and the condition of this tool.

 With the engine stopped, hand-carry the chainsaw

ZLWKWKHPXIÀHUDZD\IURP\RXUERG\DQGWKHJXLGH

bar and chain to the rear, preferably covered with a

scabbard.

MAINTAINING YOUR SAW

 +DYHDOOFKDLQVDZVHUYLFHSHUIRUPHGE\DTXDOL¿HG

VHUYLFHGHDOHUZLWKWKHH[FHSWLRQRIWKHLWHPV

listed in the maintenance section of this manual.

)RUH[DPSOHLILPSURSHUWRROVDUHXVHGWRUHPRYH

RUKROGWKHÀ\ZKHHOZKHQVHUYLFLQJWKHFOXWFK

VWUXFWXUDOGDPDJHWRWKHÀ\ZKHHOFDQRFFXUDQG

FDXVHWKHÀ\ZKHHOWREXUVW

 0DNHFHUWDLQWKHVDZFKDLQVWRSVPRYLQJZKHQWKH

throttle trigger is released. For correction, refer to

Carburetor Adjustment.

 Never modify your saw in any way.

 Keep the handles dry, clean, and free of oil or fuel

PL[WXUH

 Keep fuel and oil caps, screws, and fasteners

securely tightened.

 Use only genuine accessories and replacement

parts as recommended.

 Certain regions require by law that many internal

combustion engines are to be equipped with a spark

arresting screen. If you operate a chainsaw in a

ORFDOHZKHUHVXFKUHJXODWLRQVH[LVW\RXDUHOHJDOO\

responsible for maintaining the operating condition

of these parts. Failure to do so is a violation of

WKHODZ5HIHUWRWKH0$,17(1$1&(VHFWLRQIRU

maintenance of the spark arresting screen.

HANDLING FUEL

 Do not smoke while handling fuel or while operating

the saw.

 (OLPLQDWHDOOVRXUFHVRIVSDUNVRUÀDPHLQWKHDUHDV

ZKHUHIXHOLVPL[HGRUSRXUHG7KHUHVKRXOGEHQR

VPRNLQJRSHQÀDPHVRUZRUNWKDWFRXOGFDXVH

sparks. Allow engine to cool before refueling.



$OZD\VKDYH¿UHH[WLQJXLVKLQJWRROVDYDLODEOHLI\RX

should need them.



0L[DQGSRXUIXHOLQDQRXWGRRUDUHDRQEDUHJURXQG

store fuel in a cool, dry, well ventilated place; and

use an approved, marked container for all fuel

purposes. Wipe up all fuel spills before starting saw.

 0RYHDWOHDVWPHWHUVIHHWIURPIXHOLQJVLWH

before starting engine.

 Turn the engine off and let saw cool in a non-

combustible area, not on dry leaves, straw, paper,

etc. Slowly remove fuel cap and refuel unit.

 Store the unit and fuel in an area where fuel vapors

FDQQRWUHDFKVSDUNVRURSHQÀDPHVIURPZDWHU

heaters, electric motors or switches, furnaces, etc.

UNDERSTANDING KICKBACK

a WARNING! Avoid kickback which can result

in serious injury. Kickback is the backward,

upward or sudden forward motion of the

guide bar occurring when the saw chain near

the upper tip of the guide bar contacts any

object such as a log or branch, or when the

wood closes in and pinches the saw chain

in the cut. Contacting a foreign object in the

wood can also result in loss of chainsaw

control.

ROTATIONAL KICKBACK

Rotational kickback can occur when the moving chain

contacts an object at the upper tip of the guide bar.

This contact can cause the chain to dig into the object,

which stops the chain for an instant. The result is a

lightning fast, reverse reaction which kicks the guide

bar up and back toward the operator.

PINCH KICKBACK

Pinch kickback can occur when the wood closes in

and pinches the moving saw chain in the cut along

the top of the guide bar and the saw chain is suddenly

stopped. This sudden stopping of the chain results

in a reversal of the chain force used to cut wood and

causes the saw to move in the opposite direction of

the chain rotation. The saw is driven straight back

toward the operator.

PULL-IN

Pull-in can occur when the moving chain contacts a

foreign object in the wood in the cut along the bottom

of the guide bar and the saw chain is suddenly

stopped. This sudden stopping pulls the saw forward

and away from the operator and could easily cause

the operator to lose control of the saw.

REDUCING THE CHANCE OF

KICKBACK

 Recognize that kickback can happen. With a basic

understanding of kickback, you can reduce the

element of surprise which contributes to accidents.

 Never let the moving chain contact any object at the

tip of the guide bar.

 Keep the working area free from obstructions such

as other trees, branches, rocks, fences, stumps,

etc. Eliminate or avoid any obstruction that your saw

chain could hit while you are cutting. When cutting

a branch, do not let the guide bar contact branch or

other objects around it.

 Keep your saw chain sharp and properly tensioned.

A loose or dull chain can increase the chance of

kickback occurring. Follow manufacturer’s chain

sharpening and maintenance instructions. Check

tension at regular intervals with the engine stopped,

QHYHUZLWKWKHHQJLQHUXQQLQJ0DNHVXUHWKHEDU

nuts are securely tightened after tensioning the

chain.

 Begin and continue cutting at full speed. If the chain

is moving at a slower speed, there is greater chance

of kickback occurring.

 Use wedges made of plastic or wood. Never use

metal to hold the cut open.

 Cut one log at a time.



8VHH[WUHPHFDXWLRQZKHQUHHQWHULQJDSUHYLRXV

cut.

 Do not attempt cuts starting with the tip of the bar

SOXQJHFXWV

 Watch for shifting logs or other forces that could

close a cut and pinch or fall into chain.

 Do not twist the saw as the bar is withdrawn from an

undercut when bucking.

 Use the reduced-kickback guide bar and low-

NLFNEDFNFKDLQVSHFL¿HGIRU\RXUVDZ

MAINTAINING CONTROL

 .HHSDJRRG¿UPJULSRQWKHVDZZLWKERWKKDQGV

ZKHQWKHHQJLQHLVUXQQLQJDQGGRQ¶WOHWJR$¿UP

grip will help you reduce kickback and maintain

FRQWURORIWKHVDZ.HHSWKH¿QJHUVRI\RXUOHIW

hand encircling and your left thumb under the front

handlebar. Keep your right hand completely around

the rear handle whether you are right handed or left

handed. Keep your left arm straight with the elbow

locked.

 Position your left hand on the front handlebar so it

is in a straight line with your right hand on the rear

handle when making bucking cuts. Never reverse

right and left hand positions for any type of cutting.

 Stand with your weight evenly balanced on both feet.

 Stand slightly to the left side of the saw to keep

your body from being in a direct line with the cutting

chain.

 Do not overreach. You could be drawn or thrown off

balance and lose control of the saw.



'RQRWFXWDERYHVKRXOGHUKHLJKW,WLVGLI¿FXOWWR

maintain control of saw above shoulder height.

KICKBACK SAFETY FEATURES

a WARNING! The following features are

included on your saw to help reduce the

hazard of kickback; however, such features

will not totally eliminate this danger.

As a chainsaw user, do not rely only on

safety devices. You must follow all safety

precautions, instructions, and maintenance

in this manual to help avoid kickback and

other forces which can result in serious

injury.

REDUCED KICKBACK GUIDE BAR

The reduced-kickback guide bar is designed with a

small radius tip which reduces the size of the kickback

danger zone on the bar tip.

LOW-KICKBACK CHAIN

A low-kickback chain is designed with a contoured

GHSWKJDXJHDQGJXDUGOLQNZKLFKGHÀHFWNLFNEDFN

force and allow wood to gradually ride into the cutter.

FRONT HAND GUARD

The front hand guard is designed to reduce the

chance of your left hand contacting the chain if your

hand slips off the front handlebar.

7KHGLVWDQFHDQG³LQOLQH´SRVLWLRQRIWKHKDQGV

provided by the front and rear handles work together

to give balance and resistance in controlling the

pivot of the saw back toward the operator if kickback

occurs.

CHAIN BRAKE

The chain brake is designed to stop the chain in the

event of kickback.

NOTE: We do not represent and you should not

assume that the chain brake will protect you in the

event of a kickback. Do not rely upon any of the

devices built into your saw. You should use the saw

properly and carefully to avoid kickback.

Repairs on a chain brake should be made by an

authorized servicing dealer. Take your unit to the place

of purchase if purchased from a servicing dealer, or to

the nearest authorized master service dealer.

ASSEMBLY

3URWHFWLYHJORYHVQRWSURYLGHGVKRXOGEHZRUQGXULQJ

assembly.

NOTE: Chain brake must be unlocked before

clutch cover can be removed or reinstalled on the

chain saw. To unlock chain brake, pull the front

hand guard back toward the front handle as far as

SRVVLEOHVHHLOOXVWUDWLRQ

ATTACHING THE BUMPER SPIKE

(If not already attached)

The bumper spike may be used as a pivot when

making a cut.



0RYH216723VZLWFKWRWKH6723SRVLWLRQ

 Unlock chain brake.

3. Loosen and remove the chain brake nuts and the

clutch cover from the saw.

NOTE: If clutch cover can not be easily removed

from the chain saw, ensure chain brake is unlocked

by pulling the front hand guard back toward the

front handle as far as possible.

4. Attach the bumper spike with the two screws as

shown.

ATTACHING THE BAR & CHAIN

(If not already attached)

a WARNING: If received assembled, repeat

all steps to ensure your saw is properly

assembled and all fasteners are secure.

Always wear gloves when handling the

chain. The chain is sharp and can cut you

even when it is not moving!



0RYH216723VZLWFKWRWKH6723SRVLWLRQ

 Unlock chain brake.

3. Loosen and remove the bar nuts and the clutch

cover from the saw.

NOTE: If clutch cover can not be easily removed

from the chain saw, ensure chain brake is unlocked

by pulling the front hand guard back toward the

front handle as far as possible.

4. 5HPRYHWKHSODVWLFVKLSSLQJVSDFHULISUHVHQW

 An adjustment pin and screw is used to adjust

the tension of the chain. It is very important when

DVVHPEOLQJWKHEDUWKDWWKHDGMXVWPHQWSLQ$

SDVVHVWKURXJKWKHORZHUEDUSLQKROH%7XUQLQJ

WKHVFUHZ&ZLOOPRYHWKHDGMXVWPHQWSLQXSDQG

down the screw. Locate this adjustment pin before

you begin mounting the bar onto the saw. See

following illustration.

6. Use the screwdriver end of the bar tool to turn

the adjustment screw counterclockwise. Turn the

VFUHZXQWLOWKHDGMXVWPHQWSLQ$LVORFDWHGDOO

the way to the right side of the adjustment travel

pocket as shown in view above. This should allow

the pin to be near the correct position.

7. Slide guide bar on bar bolts until guide bar stops

against clutch drum sprocket.



Carefully remove the chain from the package. Hold

chain with the drive links as shown.

9. 3ODFHFKDLQRYHUDQGEHKLQGFOXWFKGUXP¿WWLQJ

the drive links in the clutch drum sprocket.

Fit bottom of drive links between the teeth in the

sprocket in the nose of the guide bar.

Fit chain drive links into bar groove.

Pull guide bar forward until chain is snug in guide

bar groove. Ensure all drive links are in the bar

groove.

Now, install clutch cover making sure the

adjustment pin is positioned in the lower bar pin

hole. Remember this pin moves the bar forward

and backward as the screw is turned.

,QVWDOOEDUQXWVDQG¿QJHUWLJKWHQRQO\2QFHWKH

chain is tensioned, you will need to tighten bar

nuts.

CHAIN TENSION

(Including units with chain already installed)

a WARNING: Wear protective gloves when

handling chain. The chain is sharp and can

cut you even when it is not moving.

NOTE: When adjusting chain tension, make sure

WKHEDUQXWVDUH¿QJHUWLJKWRQO\$WWHPSWLQJWR

tension the chain when the bar nuts are tight can

cause damage.

CHECKING THE TENSION

Use the screwdriver end of the chain adjustment tool

EDUWRROWRPRYHFKDLQDURXQGJXLGHEDU,IWKHFKDLQ

does not rotate, it is too tight. If the chain is too loose,

it will sag below the bar.

ADJUSTING THE TENSION

Chain tension is very important. Chains stretch during

XVH7KLVLVHVSHFLDOO\WUXHGXULQJWKH¿UVWIHZWLPHV

you use your saw. Always check chain tension each

time before you start the chain saw.

 /RRVHQEDUQXWVXQWLOWKH\DUH¿QJHUWLJKWDJDLQVW

the clutch cover.

 Turn adjustment screw clockwise until chain solidly

contacts bottom of guide bar rail.

3. Using bar tool, roll chain around guide bar to

ensure all links are in bar groove.

4. Lift up tip of guide bar to check for sag. Release tip

RIJXLGHEDUWKHQWXUQDGMXVWPHQWVFUHZWXUQ

FORFNZLVH5HSHDWXQWLOVDJGRHVQRWH[LVW

 While lifting tip of guide bar, tighten bar nuts

securely with the bar tool.

6. Use the screwdriver end of the bar tool to move

chain around guide bar.

7. If chain does not rotate, it is too tight. Slightly

loosen bar nuts and loosen chain by turning the

DGMXVWPHQWVFUHZWXUQFRXQWHUFORFNZLVH

Retighten bar nuts.

 If chain is too loose, it will sag below the guide bar.

DO NOT operate the saw if the chain is loose.

NOTE: The chain is tensioned correctly when

the weight of the chain does not cause it to sag

below the guide bar (with the chain saw sitting in

DQXSULJKWSRVLWLRQEXWWKHFKDLQVWLOOPRYHVIUHHO\

around the guide bar.

a WARNING: If the saw is operated with

a loose chain, the chain could jump off

the guide bar and result in serious injury

to the operator and/or damage the chain

making it unusable. If the chain jumps off

the guide bar, inspect each drive link for

damage. Damaged chain must be repaired

or replaced.

FUEL HANDLING

FUELING ENGINE

a WARNING: Remove fuel cap slowly when

refueling.

,03257$177KLVHTXLSPHQWLVGHVLJQHGWRRSHUDWH

RQXQOHDGHGJDVROLQHZLWKDPLQLPXPRFWDQH$.,

ZLWKHWKDQROEOHQGHGXSWRPD[LPXPE\YROXPH

(%HIRUHRSHUDWLRQJDVROLQHPXVWEHPL[HGZLWK

DJRRGTXDOLW\V\QWKHWLFF\FOHDLUFRROHGHQJLQHRLO

GHVLJQHGWREHPL[HGDWDUDWLRRI

DO NOT USE automotive oil or marine oil. These oils

ZLOOFDXVHHQJLQHGDPDJH:KHQPL[LQJIXHOIROORZ

instructions printed on container. Once oil is added to

gasoline, shake container momentarily to assure that

WKHIXHOLVWKRURXJKO\PL[HG$OZD\VUHDGDQGIROORZ

the safety rules relating to fuel before fueling your unit.

3XUFKDVHIXHOLQTXDQWLWLHVWKDWFDQEHXVHGZLWKLQ

days to assure fuel freshness.

CAUTION: Never use straight gasoline in your unit.

This will cause permanent engine damage and void

the limited warranty. Do not use alternate fuels such

DVHWKDQROEOHQGVDERYHE\YROXPH(

(RUDQ\PHWKDQROEOHQGHGIXHO8VHRIWKHVH

fuels can cause major engine performance and

durability problems.

Gasoline, gallons Two-stroke oil, ounces







 

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubrication.

Lubrication is provided by the automatic oiler system

ZKHQWKHRLOWDQNLVNHSW¿OOHG/DFNRIRLOZLOOTXLFNO\

ruin the bar and chain.

Too little oil will cause overheating shown by smoke

coming from the chain and/or discoloration of the

bar. In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a small

DPRXQWWRRI'LHVHO)XHORUNHURVHQH%DU

DQGFKDLQRLOPXVWEHIUHHÀRZLQJIRUWKHRLOV\VWHPWR

pump enough oil for adequate lubrication.

Bar and chain oil is recommended to protect your unit

DJDLQVWH[FHVVLYHZHDUIURPKHDWDQGIULFWLRQ,IEDU

and chain oil is not available, use a good grade SAE

RLO

 Never use waste oil for bar and chain lubrication.

 Always stop the engine before removing the oil cap.

STARTING AND STOPPING

CHAIN BRAKE

Ensure chain brake is unlocked by pulling the front

hand guard back toward the front handle as far as

possible. The chain brake must be unlocked before

cutting with the saw.

a WARNING: The chain must not move when

the engine runs at idle speed. If the chain

moves at idle speed refer to CARBURETOR

ADJUSTMENT within this manual.

a :$51,1*$YRLGFRQWDFWZLWKWKHPXIÀHU$

KRWPXIÀHUFDQFDXVHVHULRXVEXUQV

To stop the engine move the ON/STOP switch to the

STOP position.

7RVWDUWWKHHQJLQHKROGWKHVDZ¿UPO\RQWKHJURXQG

DVLOOXVWUDWHG0DNHVXUHWKHFKDLQLVIUHHWRWXUQ

without contacting any object.

a WARNING: Do not attempt to throw or drop-

start the chain saw. Doing so will put the

operator at risk of serious injury due to loss

of control of the chain saw.

,03257$17:KHQSXOOLQJWKHVWDUWHUURSHGRQRW

XVHWKHIXOOH[WHQWRIWKHURSHDVWKLVFDQFDXVHWKH

rope to break. Do not let starter rope snap back.

Hold the handle and let the rope rewind slowly.

NOTE: For cold weather starting, start the unit at

FULL CHOKE; allow the engine to warm up before

squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke

lever in the FULL CHOKE position.

HELPFUL TIP: If your engine still does not start

after following these instructions, please call

customer support.

STARTING A COLD ENGINE

NOTE: In the following steps, when the choke lever

LVSXOOHGRXWWRWKHIXOOH[WHQWWKHFRUUHFWWKURWWOH

setting for starting is set automatically.

 The chain brake must be locked when the chain saw

is started. Lock the brake by moving the front hand

guard forward.

 0RYH216723VZLWFKWRWKH21SRVLWLRQ

 Grip the front handle with your left hand. Hold the

chain saw on the ground by placing your right foot

through the rear handle.

127(7KHUHLVDVLPSOL¿HGVWDUWUHPLQGHUZLWK

illustrations to describe each step on the rear edge

of the saw.

 3UHVVWKHSULPHUWLPHV7KHEXOEGRHVQHHGQRW

WREHFRPSOHWHO\¿OOHGZLWKIXHO

 Pull the choke lever out to the full choke position.

3. Pull the starter handle with your right hand and

pull out the starter cord slowly until you feel a

UHVLVWDQFHDVWKHVWDUWHUSDZOVHQJDJHWKHQSXOO

¿UPO\DQGUDSLGO\WLPHV

NOTE: If the engine sounds as if it is trying to start

EHIRUHWKHWKSXOOVWRSSXOOLQJDQGLPPHGLDWHO\

SURFHHGWRWKHQH[WVWHS

4. Push the choke lever to the half choke position.

 3XOOWKHVWDUWHUKDQGOH¿UPO\DQGUDSLGO\XQWLOWKH

engine starts.

$OORZWKHHQJLQHWRUXQIRUDSSUR[LPDWHO\VHFRQGV

Then, squeeze and release the throttle trigger to allow

engine to return to idle speed.

NOTE: Ensure chain brake is unlocked by pulling

the front hand guard back toward the front handle

as far as possible. The chain brake must be

unlocked before cutting with the saw. The chain saw

is now ready for use.

STARTING A WARM ENGINE

)ROORZVWHSVDQGLQWKHFROGHQJLQHVWDUWLQJ

instructions.

a WARNING! Long term inhalation of the

engine’s exhaust fumes, chain oil mist

and dust from sawdust can represent a

health risk.

DIFFICULT STARTING

RUVWDUWLQJDÀRRGHGHQJLQH

7KHHQJLQHPD\EHÀRRGHGZLWKWRRPXFKIXHOLILW

KDVQRWVWDUWHGDIWHUSXOOV)ORRGHGHQJLQHVFDQ

EHFOHDUHGRIH[FHVVIXHOE\SXVKLQJWKHFKRNHOHYHU

LQFRPSOHWHO\WRWKH2))&+2.(SRVLWLRQDQGWKHQ

following the warm engine starting procedure.

Ensure the ON/STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly the

XQLWLVÀRRGHG,IHQJLQHIDLOVWRVWDUWUHIHUWRWKH

TROUBLESHOOTING TABLE or call customer

support.

STOPPING

Stop the engine by pushing the start/stop switch down.

a WARNING! To avoid involuntary start up,

the spark plug cap must always be removed

from the spark plug when the machine is

unsupervised.

CHAIN BRAKE

a WARNING: If the brake band is worn too

thin it may break when the chain brake is

triggered. With a broken brake band, the

chain brake will not stop the chain. The

chain brake should be replaced by an

authorized service dealer if any part is worn

to less than 0.5 mm (0.020 in) thick. Repairs

on a chain brake should be made by an

authorized service dealer.

Take your unit to the place of purchase if

purchased from a servicing dealer, or to the

nearest authorized master service dealer.

This saw is equipped with a chain brake. The brake is

designed to stop the chain if kickback occurs.

The inertia-activated chain brake is locked if the front

hand guard is pushed forward, either manually (by

KDQGRUDXWRPDWLFDOO\E\VXGGHQPRYHPHQW

If the brake is already locked, it is unlocked by pulling

the front handguard back toward the front handle as

far as possible.

When cutting with the saw, the chain brake must be

unlocked.

BRAKING FUNCTION CONTROL

NOTE: The chain brake must be checked several

times daily. The engine must be running when

performing this procedure.

This is the only instance when the saw should be

placed on the ground with the engine running.

3ODFHWKHVDZRQ¿UPJURXQG*ULSWKHUHDUKDQGOH

with your right hand and the front handle with your left

hand. Apply full throttle by fully depressing the throttle

trigger. Activate the chain brake by turning your left

wrist against the hand guard without releasing your

grip around the front handle. The chain should stop

immediately.

WORKING TECHNIQUES

PRACTICING YOUR CUTS

Practice cutting a few small logs using the following

WHFKQLTXHVWRJHWWKH³IHHO´RIXVLQJ\RXUVDZEHIRUH

you begin a major sawing operation.

 Squeeze the throttle trigger and allow the engine to

reach full speed before cutting.

 Begin cutting with the saw frame against the log.

 Keep the engine at full speed the entire time you are

cutting.



$OORZWKHFKDLQWRFXWIRU\RX([HUWRQO\OLJKW

downward pressure. If you force the cut, damage to

the guide bar, chain, or engine can result.

 Release the throttle trigger as soon as the cut

is completed, allowing the engine to idle. If you

run the saw at full throttle without a cutting load,

unnecessary wear can occur to the chain, guide

bar, and engine. It is recommended that the engine

QRWEHRSHUDWHGIRUORQJHUWKDQVHFRQGVDWIXOO

throttle.

 To avoid losing control when cut is complete, do not

put pressure on saw at end of cut.

 Stop the engine before setting the saw down after

cutting.

FELLING A TREE

PLANNING

a WARNING! Check for broken or dead

branches which can fall while cutting

causing serious injury. Do not cut near

buildings or electrical wires if you do not

know the direction of tree fall, nor cut at

night since you will not be able to see well,

nor during bad weather such as rain, snow,

or strong winds, etc. If the tree makes

contact with any utility line, the utility

FRPSDQ\VKRXOGEHQRWL¿HGLPPHGLDWHO\

Carefully plan your sawing operation in advance.

Clear the work area. You need a clear area all around

the tree so you can have secure footing.

The chainsaw operator should keep on the uphill side

of the terrain as the tree is likely to roll or slide downhill

after it is felled.

Study the natural conditions that can cause the tree to

fall in a particular direction.

Natural conditions that can cause a tree to fall in a

particular direction include:

 The wind direction and speed.

 The lean of the tree. The lean of a tree might not be

apparent due to uneven or sloping terrain. Use a

plumb or level to determine the direction of tree lean.

 Weight and branches on one side.

 Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted, it can

snap and fall toward the operator. Check for broken or

dead branches which can fall on you while cutting.

0DNHVXUHWKHUHLVHQRXJKURRPIRUWKHWUHHWRIDOO

0DLQWDLQDGLVWDQFHRIWUHHOHQJWKVIURPWKH

nearest person or other objects. Engine noise can

drown out a warning call.

Remove dirt, stones, loose bark, nails, staples, and

wire from the tree where cuts are to be made.

Plan a clear retreat path to the rear and diagonal to

WKHOLQHRIIDOO1RWHWKHGDQJHU]RQHUHWUHDWSDWK

DQGIHOOLQJGLUHFWLRQLQWKHIROORZLQJGLDJUDP

USING THE NOTCH METHOD

The notch method is used to fell large trees. A notch

is cut on the side of the tree in the desired direction of

fall. After a felling cut is made on the opposite side of

tree, the tree will tend to fall into the notch.

NOTE: If the tree has large buttress roots, remove

them before making the notch. If using saw to

remove buttress roots, keep saw chain from

contacting ground to prevent dulling of the chain.

0DNHWKHQRWFKFXWE\FXWWLQJWKHWRSRIWKHQRWFK

¿UVW&XWWKURXJKRIWKHGLDPHWHURIWKHWUHH1H[W

complete the notch by cutting the bottom of the notch.

Once the notch is cut remove the notch of wood from

the tree.

After removing the wood from the notch, make the

felling cut on the opposite side of the notch. This is

GRQHE\PDNLQJDFXWDERXWFHQWLPHWHUVLQFKHV

higher than the center of the notch. This will leave

enough uncut wood between the felling cut and the

notch to form a hinge. This hinge will help prevent the

tree from falling in the wrong direction.

NOTE: Before felling cut is complete, use wedges to

open the cut if necessary to control the direction of

fall. To avoid kickback and chain damage, use wood

or plastic wedges, but never steel or iron wedges.

Be alert to signs that the tree is ready to fall: cracking

sounds, widening of the felling cut, or movement in the

upper branches.

As tree starts to fall, stop saw, put it down, and get

away quickly on your planned retreat path.

DO NOT cut down a partially fallen tree with your saw.

%HH[WUHPHO\FDXWLRXVZLWKSDUWLDOO\IDOOHQWUHHVWKDW

may be poorly supported. When a tree doesn’t fall

completely, set the saw aside and pull down the tree

with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the

desired log size.

a WARNING! Do not stand on the log being

cut. Any portion can roll causing loss of

footing and control. Do not stand downhill of

the log being cut.

,03257$1732,176

 Cut only one log at a time.

 Cut shattered wood very carefully; sharp pieces of

ZRRGFRXOGEHÀXQJWRZDUGRSHUDWRU

 Use a sawhorse to cut small logs. Never allow

another person to hold the log while cutting and

never hold the log with your leg or foot.

 Do not cut in an area where logs, limbs, and roots

are tangled such as in a blown down area. Drag

the logs into a clear area before cutting by pulling

RXWH[SRVHGDQGFOHDUHGORJV¿UVW

 0DNHVXUHWKHFKDLQZLOOQRWVWULNHWKHJURXQGRU

any other object during or after cutting.

a WARNING! If saw becomes pinched or hung

in a log, don’t try to force it out. You can lose

control of the saw resulting in injury and/

or damage to the saw. Stop the saw, drive a

wedge of plastic or wood into the cut until

the saw can be removed easily. Restart the

saw and carefully reenter the cut. To avoid

kickback and chain damage, do not use a

metal wedge. Do not attempt to restart your

saw when it is pinched or hung in a log.

TYPES OF BUCKING CUTS

Overcutting begins on the top side of the log with the

bottom of the saw against the log. When overcutting

use light downward pressure.

Undercutting involves cutting on the underside of the

log with top of saw against the log. When undercutting

XVHOLJKWXSZDUGSUHVVXUH+ROGVDZ¿UPO\DQG

maintain control. The saw will tend to push back

toward you.

a WARNING! Never turn saw upside down to

undercut. The saw cannot be controlled in

this position.

$OZD\VPDNH\RXU¿UVWFXWRQWKHFRPSUHVVLRQVLGHRI

the log. The compression side of the log is where the

pressure of the log’s weight is concentrated.

BUCKING WITHOUT A SUPPORT

 2YHUFXWWKURXJKRIWKHGLDPHWHURIWKHORJ

 5ROOWKHORJRYHUDQG¿QLVKZLWKDVHFRQGRYHUFXW

NOTE: Watch for logs with a compression side to

prevent the saw from pinching.

BUCKING USING A LOG OR SUPPORT

STAND

 0DNHWKH¿UVWFXWRQWKHFRPSUHVVLRQVLGHRIWKH

ORJ<RXU¿UVWFXWVKRXOGH[WHQGRIWKHGLDPHWHU

of the log.

 Finish with your second cut.

LIMBING AND PRUNING

a WARNING! Be alert for and guard against

kickback. Do not allow the moving chain to

contact any other branches or objects at

the nose of the guide bar when limbing or

pruning. Allowing such contact can result in

serious injury.

a WARNING! Never climb into a tree to limb or

prune. Do not stand on ladders, platforms, a

log, or in any position which can cause you

to lose your balance or control of the saw.

,03257$1732,176

 :RUNVORZO\NHHSLQJERWKKDQGV¿UPO\JULSSHGRQ

WKHVDZ0DLQWDLQVHFXUHIRRWLQJDQGEDODQFH

 Watch out for springpoles. Springpoles are small

size limbs which can catch the saw chain and

whip toward you or pull you off balance. Use

H[WUHPHFDXWLRQZKHQFXWWLQJVPDOOVL]HOLPEVRU

slender material.

 Be alert for springback. Watch out for branches

that are bent or under pressure. Avoid being

struck by the branch or the saw when the tension

LQWKHZRRG¿EHUVLVUHOHDVHG

 Keep a clear work area. Frequently clear

branches out of the way to avoid tripping over

them.

LIMBING

Always limb a tree after it is cut down. Only then can

limbing be done safely and properly.

Leave the larger limbs underneath the felled tree to

support the tree as you work.

Start at the base of the felled tree and work toward the

top, cutting branches and limbs. Remove small limbs

with one cut.

Keep the tree between you and the chain. Cut from

the side of the tree opposite the branch you are

cutting.

Remove larger, supporting branches with the cutting

techniques described in BUCKING WITHOUT A

SUPPORT.

Always use an overcut to cut small and freely hanging

limbs. Undercutting could cause limbs to fall and pinch

the saw.

PRUNING

a WARNING! Limit pruning to limbs shoulder

height or below. Do not cut if branches

are higher than your shoulder. Get a

professional to do the job.



0DNHWKH¿UVWFXWRQHWKLUGRIWKHZD\WKURXJKWKH

bottom of the limb.

 0DNHWKHVHFRQGFXWDOOWKHZD\WKURXJKWKHOLPE

3. 0DNHWKHWKLUGRYHUFXWOHDYLQJDWR

FHQWLPHWHUWRLQFKFROODUIURPWKHWUXQNRIWKH

tree.

MAINTENANCE

a WARNING: Disconnect the spark plug

before performing maintenance except for

carburetor adjustments.

We recommend all service and adjustments

not listed in this manual be performed by an

authorized or Master Service Dealer.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that

have been subjected to operator abuse or negligence.

To receive full value from the warranty, the operator

must maintain the unit as instructed in this manual.

Various adjustments will need to be made periodically

to properly maintain your unit.

,03257$17+DYHDOOUHSDLUVRWKHUWKDQWKH

recommended maintenance described in the

instruction manual performed by an authorized

service dealer.

If any dealer other than an authorized service

dealer performs work on the product, the company

may not pay for repairs under warranty. It is your

responsibility to maintain and perform general

maintenance.

MAINTENANCE SCHEDULE

Before each use

 &KHFNIXHOPL[WXUHOHYHO

 Check bar lubrication

 Check chain tension

 Check chain sharpness

 Check for damaged parts

 Check for loose caps

 Check for loose fasteners

 Check for loose parts

Every 5 hours*

 ,QVSHFWDQGFOHDQDLU¿OWHU

 Inspect and clean chain brake

 Inspect and clean guide bar

Every 25 hours*

 ,QVSHFWDQGFOHDQVSDUNDUUHVWLQJVFUHHQDQGPXIÀHU

Yearly

 Replace spark plug



5HSODFHIXHO¿OWHU

 5HSODFHDLU¿OWHU

(DFKKRXURIRSHUDWLRQLVDSSUR[LPDWHO\WDQNVRI

fuel.

MAINTENANCE PROCEDURES

CHECK FOR DAMAGED OR WORN PARTS

Contact an authorized service dealer for replacement

of damaged or worn parts.

NOTE: It is normal for a small amount of oil to

appear under the saw after engine stops. Do not

confuse this with a leaking oil tank.

 ON/STOP Switch - Ensure ON/STOP switch

functions properly by moving the switch to the STOP

SRVLWLRQ0DNHVXUHHQJLQHVWRSVWKHQUHVWDUW

engine and continue.

 Fuel Tank - Do not use saw if fuel tank shows signs

of damage or leaks.

 Oil Tank - Do not use saw if oil tank shows signs of

damage or leaks.

CHECK FOR LOOSE FASTENERS AND

PARTS

 Bar Nuts

 Chain

 0XIÀHU

 Cylinder Shield

 Air Filter

 Handle Screws



9LEUDWLRQ0RXQWV

 Starter Housing

 Front Hand Guard

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A dull chain makes

a sawdust powder and cuts slowly. See CHAIN

SHARPENING.

GUIDE BAR

Conditions which require guide bar maintenance:

 Saw cuts to one side or at an angle.

 Saw has to be forced through the cut.

 Inadequate supply of oil to bar/chain.

Check the condition of guide bar each time chain is

sharpened. A worn guide bar will damage the chain

DQGPDNHFXWWLQJGLI¿FXOW

After each use, ensure ON/STOP switch is in the

STOP position, then clean all sawdust from the guide

bar and sprocket hole.

To maintain guide bar:

 0RYH216723VZLWFKWR6723

 Loosen and remove bar nuts and clutch cover.

Remove bar and chain from saw.

3. &OHDQWKHRLOKROHV$DQGEDUJURRYH%

4. Burring of guide bar rails is a normal process of rail

ZHDU5HPRYHWKHVHEXUUVZLWKDÀDW¿OH

 :KHQUDLOWRSLVXQHYHQXVHDÀDW¿OHWRUHVWRUH

square edges and sides.

Replace guide bar when the groove is worn, the guide

EDULVEHQWRUFUDFNHGRUZKHQH[FHVVKHDWLQJRU

burring of the rails occurs. If replacement is necessary,

XVHRQO\WKHJXLGHEDUVSHFL¿HGIRU\RXUVDZLQ

the repair parts list or on the decal located on the

chainsaw.

CHECK FUEL MIXTURE LEVEL

See FUELING ENGINE under the OPERATION

section.

LUBRICATION

See GUIDE BAR AND CHAIN OIL under the

OPERATION section.

INSPECT AND CLEAN THE UNIT AND

DECALS

After each use, inspect complete unit for loose or

damaged parts. Clean the unit and decals using a

damp cloth with a mild detergent.

Wipe off unit with a clean dry cloth.

CHECK THE CHAIN BRAKE

See CHAIN BRAKE in the OPERATION section.

CLEAN AIR FILTER

a :$51,1*'RQRWFOHDQ¿OWHULQJDVROLQHRU

RWKHUÀDPPDEOHVROYHQWWRDYRLGFUHDWLQJD

¿UHKD]DUGRUSURGXFLQJKDUPIXOHPLVVLRQV

$GLUW\DLU¿OWHUGHFUHDVHVWKHOLIHDQGSHUIRUPDQFH

of the engine and increases fuel consumption and

KDUPIXOHPLVVLRQV$OZD\VFOHDQ\RXUDLU¿OWHUDIWHU

WDQNVRIIXHORUKRXUVRIRSHUDWLRQZKLFKHYHU

FRPHV¿UVW&OHDQPRUHIUHTXHQWO\LQGXVW\FRQGLWLRQV

$XVHGDLU¿OWHUFDQQHYHUEHFRPSOHWHO\FOHDQHG,WLV

DGYLVDEOHWRUHSODFH\RXUDLU¿OWHUZLWKDQHZRQHDIWHU

HYHU\KRXUVRIRSHUDWLRQRUDQQXDOO\ZKLFKHYHU

FRPHV¿UVW

 /RRVHQNQRERQDLU¿OWHUFRYHU5HPRYHDLU¿OWHU

cover.



3UHVVGRZQRQZLUHFODPSWRUHOHDVHDLU¿OWHU

5HPRYHDLU¿OWHU

3. &OHDQWKHDLU¿OWHUXVLQJKRWVRDS\ZDWHU5LQVH

with clean cool water. Air dry completely before

reinstalling.

4. 5HLQVWDOODLU¿OWHUDQGUHSRVLWLRQZLUHFODPS

127((QVXUHDLU¿OWHULVFRUUHFWO\LQVWDOOHGDQG

fully seated in pocket before repositioning wire

FODPSDQGUHLQVWDOOLQJDLU¿OWHUFRYHU

 5HLQVWDOODLU¿OWHUFRYHU7LJKWHQNQREVHFXUHO\

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

As the unit is used, carbon deposits build up on the

PXIÀHUDQGVSDUNDUUHVWLQJVFUHHQDQGPXVWEH

UHPRYHGWRDYRLGFUHDWLQJD¿UHKD]DUGRUDIIHFWLQJ

engine performance.

Replace the spark arresting screen if breaks occur.

CLEANING THE SPARK ARRESTING

SCREEN

 &OHDQLQJLVUHTXLUHGHYHU\KRXUVRIRSHUDWLRQRU

DQQXDOO\ZKLFKHYHUFRPHV¿UVW

 /RRVHQNQRERQDLU¿OWHUFRYHU5HPRYHDLU¿OWHU

cover.

3. Loosen 3 screws on cylinder cover.

Remove the cylinder cover.

4. /RRVHQDQGUHPRYHWKHVFUHZIURPWKHPXIÀHU

H[KDXVWRXWOHWFRYHU

 Remove spark arresting screen. Handle screen

carefully to prevent damage.

6. Clean the spark arresting screen gently with a wire

brush. Replace screen if breaks are found.

7. 5HSODFHDQ\EURNHQRUFUDFNHGPXIÀHUSDUWV

 Reinstall spark arresting screen.

9. 5HLQVWDOOVFUHZLQPXIÀHUH[KDXVWRXWOHWFRYHU

Reinstall the cylinder cover and 3 screws. Tighten

securely.

5HLQVWDOODLU¿OWHUFRYHU7LJKWHQNQREVHFXUHO\

REPLACE SPARK PLUG

The spark plug should be replaced each year to

ensure the engine starts easier and runs better.

,JQLWLRQWLPLQJLV¿[HGDQGQRQDGMXVWDEOH

 /RRVHQNQRERQDLU¿OWHUFRYHU5HPRYHDLU¿OWHU

cover.

 Pull off the spark plug boot.

3. Remove spark plug from cylinder and discard.

4. 5HSODFHZLWKVSHFL¿HGVSDUNSOXJDQGWLJKWHQ

securely with a socket wrench.

 Reinstall the spark plug boot.

6. 5HLQVWDOODLU¿OWHUFRYHU7LJKWHQNQREVHFXUHO\

CARBURETOR ADJUSTMENT

a WARNING: The chain will be moving

during most of this procedure. Wear your

protective equipment and observe all safety

precautions. The chain must not move at idle

speed.

The carburetor has been carefully set at the factory.

Adjustments may be necessary if you notice any of the

following conditions:

 Chain moves at idle. See IDLE SPEED-T adjustment

procedure.

 Saw will not idle. See IDLE SPEED-T adjustment

procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast.

If the engine stalls, idle is too slow. Adjust speed until

HQJLQHUXQVZLWKRXWFKDLQPRYHPHQWLGOHWRRIDVWRU

VWDOOLQJLGOHWRRVORZ7KHLGOHVSHHGVFUHZLVORFDWHG

in the area above the primer bulb and is labeled T.

 7XUQLGOHVFUHZ7FORFNZLVHWRLQFUHDVHHQJLQH

speed.

 7XUQLGOHVFUHZ7FRXQWHUFORFNZLVHWRGHFUHDVH

engine speed.

If you require further assistance or are unsure about

performing this procedure, contact your authorized

service dealer or call customer support.

COOLING SYSTEM

To keep the working temperature as low as possible

the machine is equipped with a cooling system.

The cooling system consists of:

 Air intake on the starter

 Air guide plate



)LQVRQWKHÀ\ZKHHO

 &RROLQJ¿QVRQWKHF\OLQGHU

 &\OLQGHUFRYHUGLUHFWVFROGDLURYHUWKHF\OLQGHU

Clean the cooling system with a brush after each use,

more often in demanding conditions. A dirty or blocked

cooling system results in the machine overheating

which causes damage to the piston and cylinder.

CHAIN SHARPENING

The cutter

The cutting part of the saw chain is called the cutter and

consists of a cutting tooth (A) and the depth gauge (B).

The cutters cutting depth is determined by the difference

in height between the two, the depth gauge setting (C).

When you sharpen a cutting tooth there are four important

factors to remember:

• Filing angle.

• Cutting angle.

• File position.

• 5RXQG¿OHGLDPHWHU

To sharpen the cutting teeth

8VHDURXQG¿OHDQGD¿OHJDXJHWRVKDUSHQWKHFXWWLQJ

teeth. See the TECHNICAL DATA section of this manual

IRULQIRUPDWLRQRQWKHUHFRPPHQGHGGLPHQVLRQRIWKH¿OH

and gauge for the saw chain installed on your product.

1. Make sure that the saw chain is correctly tensioned. A

VODFNFKDLQZLOOPRYHVLGHZD\VPDNLQJLWPRUHGLI¿FXOW

to sharpen correctly.

2. )LOHDOOWHHWKRQRQHVLGH¿UVW)LOHWKHFXWWLQJWHHWK

from the inside face and reduce the pressure on the

return stroke.

3. 7XUQWKHSURGXFWRYHUDQG¿OHWKHWHHWKRQWKHRWKHU

side.

4. File all the teeth to the same length. When the length

of the cutting teeth is reduced to 4 mm (5/32”) the saw

chain is worn out and must be replaced.

To adjust the depth gauge setting

Sharpen the cutting teeth before you adjust the depth

gauge setting. When you sharpen the cutting tooth (A), the

depth gauge setting (C) will decrease. To maintain optimal

FXWWLQJSHUIRUPDQFHWKHGHSWKJDXJH%KDVWREH¿OHG

down to achieve the recommended depth gauge setting.

6HHWKH7(&+1,&$/'$7$VHFWLRQRIWKLVPDQXDOWR¿QG

the correct depth gauge setting for your particular chain.

NOTE: This recommendation assumes that

the length of the cutting teeth is not reduced

excessively.

8VHDÀDW¿OHDQGGHSWKJDXJHWRROWRDGMXVWWKHGHSWK

gauge.

1. Put the depth gauge tool above the saw chain.

Detailed information regarding how to use the depth

gauge tool will be found on the package of the depth

gauge tool.

2. 8VHWKHÀDW¿OHWR¿OHRIIWKHWLSRIWKHGHSWKJDXJH

that protrudes through the depth gauge tool. The

depth gauge setting is correct when you no longer feel

UHVLVWDQFHDV\RXGUDZWKH¿OHDORQJWKHGHSWKJDXJH

tool.

TROUBLESHOOTING

TROUBLESHOOTING TABLE

a WARNING: Always stop unit and disconnect spark plug before performing all of the recommended

remedies below except remedies that require operation of the unit.

TROUBLE CAUSE REMEDY

Engine will not start or will run only

a few seconds after starting.

 Ignition switch off.



(QJLQHÀRRGHG

3. Fuel tank empty.

4. 6SDUNSOXJQRW¿ULQJ

 Fuel not reaching carburettor.



0RYHLJQLWLRQVZLWFKWR21

 6HH³'LI¿FXOW6WDUWLQJ´LQ

STARTING AND STOPPING

Section.

3. Fill tank with correct fuel

PL[WXUH

4. Install new spark plug.

 &KHFNIRUGLUW\IXHO¿OWHU

replace.

Check for kinked or split fuel

line; repair or replace.

Engine will not idle properly.  Idle speed requires

adjustment.

 Carburettor requires

adjustment.



6HH³&DUEXUHWWRU$GMXVWPHQW´

LQWKH0$,17(1$1&(6HFWLRQ

 Contact an authorized service

dealer.

Engine will not accelerate, lacks

power, or dies under a load.



$LU¿OWHUGLUW\

 Spark plug fouled.

3. Chain brake engaged.

4. Carburettor requires

adjustment.



&OHDQRUUHSODFHDLU¿OWHU

 Clean or replace plug and

regap.

3. Disengage chain brake.

4. Contact an authorized service

dealer.

(QJLQHVPRNHVH[FHVVLYHO\  7RRPXFKRLOPL[HGZLWK

gasoline.

 (PSW\IXHOWDQNDQGUH¿OOZLWK

FRUUHFWIXHOPL[WXUH

Chain moves at idle speed.  Idle speed requires

adjustment.

 Clutch requires repair.

 6HH³&DUEXUHWWRU$GMXVWPHQW´

LQWKH0$,17(1$1&(6HFWLRQ

 Contact an authorized service

dealer.

&OXWFKFRYHUZLOOQRW¿WSURSHUO\  Chain brake is engaged.  See “Resetting the

&KDLQ%UDNH´LQWKH

TROUBLESHOOTING section.

RESETTING THE CHAIN BRAKE

If the clutch cover is removed accidentally while

the chain brake is locked, the chain brake must be

unlocked so the clutch cover can be assembled

without binding to the clutch drum.

$OLJQWKHQRWFKHVRQWKHEDUWRROVRWKDWWKH\¿WRYHU

the brake rotating link.

CAUTION: The chain brake spring is under tension.

Use care when resetting the brake.

To reset the brake, rotate the link clockwise until

it stops. NOTE: do not hold the brake band while

attempting to reset it.

The front link will be in its downward rotated position

when the chain brake is unlocked.

STORAGE

Perform the following steps after each use:

 Allow the engine to cool, and secure the unit before

storing or transporting.

 Store chain saw and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open

ÀDPHVIURPZDWHUKHDWHUVHOHFWULFPRWRUVRU

switches, furnaces, etc.

 Store chain saw with all guards in place and

position chain saw so that any sharp object cannot

accidentally cause injury.

 Store chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season

RULILWZLOOQRWEHXVHGIRUGD\VRUPRUH

If your chain saw is to be stored for a period of time:

 Clean saw thoroughly before storage.

 Store in a clean dry area.



/LJKWO\RLOH[WHUQDOPHWDOVXUIDFHVDQGJXLGHEDU

 Oil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERATION section

of this manual, see message labeled

,03257$17UHJDUGLQJWKHXVHRIJDVRKROLQ\RXU

chain saw.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits during

storage. Add stabilizer to the petrol in the fuel tank or

fuel storage container.

)ROORZWKHPL[LQVWUXFWLRQVIRXQGRQVWDELOL]HU

FRQWDLQHUV5XQHQJLQHDWOHDVWPLQXWHVDIWHUDGGLQJ

stabilizer.

ENGINE

 5HPRYHVSDUNSOXJDQGSRXUWHDVSRRQRIF\FOH

engine oil through the spark plug opening. Slowly

SXOOWKHVWDUWHUURSHWRWLPHVWRGLVWULEXWHRLO

 Replace spark plug with new one of recommended

type and heat range.

 &OHDQDLU¿OWHU

 Check entire unit for loose screws, nuts, and bolts.

Replace any damaged, broken, or worn parts.



$WWKHEHJLQQLQJRIWKHQH[WVHDVRQXVHRQO\IUHVK

fuel having the proper petrol to oil ratio.

OTHER

 Do not store petrol from one season to another.

 Replace your petrol container if it starts to rust.

TECHNICAL DATA

PR5020

(LDAV50MC)

Engine

Cylinder displacement, cm



Cylinder bore, mm 44

Stroke, mm 33

Idle speed, rpm 

Power, kW 

Ignition system

Spark plug

+XVTYDUQD+47

%ULVN35<&

Electrode gap, mm 

Fuel and lubrication system

Fuel tank capacity, cm



2LOSXPSFDSDFLW\DWUSPPOPLQ 

Oil tank capacity, cm



Type of oil pump Automatic

Weight

Chain saw without bar or chain, empty tanks

NJOE

Noise emissions (see note 1)

6RXQGSRZHUOHYHOPHDVXUHGG%$ 

6RXQGSRZHUOHYHOPHDVXUHGG%$$XVWUDOLD 

Sound power level, guaranteed L

G%$(XURSH 

Sound levels (see note 2)

(TXLYDOHQWVRXQGSUHVVXUHOHYHODWWKHRSHUDWRU¶VHDUG%$ 

Equivalent vibration levels, a hveq (see note 3)

Front handle, m/s





Rear handle, m/s





Chain/bar

Standard bar length

LQFP

Recommended bar lengths LQFP

Usable cutting length LQFP

Pitch 

Thickness of drive links PPLQ

Type of drive sprocket/number of teeth Spur/7

&KDLQVSHHGDWPD[SRZHUPVHF 

1RWH1RLVHHPLVVLRQVLQWKHHQYLURQPHQWPHDVXUHGDVVRXQGSRZHU/

LQFRQIRUPLW\ZLWK(&GLUHFWLYH

(&

1RWH(TXLYDOHQWVRXQGSUHVVXUHOHYHODFFRUGLQJWR,62LVFDOFXODWHGDVWKHWLPHZHLJKWHGHQHUJ\WRWDO

for different sound pressure levels under various working conditions. Typical statistical dispersion for equivalent

VRXQGSUHVVXUHOHYHOLVDVWDQGDUGGHYLDWLRQRIG%$

1RWH(TXLYDOHQWYLEUDWLRQOHYHODFFRUGLQJWR,62LVFDOFXODWHGDVWKHWLPHZHLJKWHGHQHUJ\WRWDOIRU

vibration levels under various working conditions. Reported data for equivalent vibration level has a typical

VWDWLVWLFDOGLVSHUVLRQVWDQGDUGGHYLDWLRQRIPV



GUIDE BAR AND SAW CHAIN COMBINATIONS

The following cutting attachments are approved for the models covered in this manual.

0RGHO Bar Chain P/N CKA without chain

brake

P/N Length

35 

LQFP  

SAW CHAIN FILING AND SAW CHAIN COMBINATIONS

Chain type Round ﬁ le

size

Depth

gauge

setting

Top plate

cutting

angle

Side plate

angle

Top plate

ﬁ ling angle

File guide

angle

US 83 G 7/32” (5.5

mm)

.025” (0.635

mm)

60° 60° 25° 10°

a ADVERTENCIA: Lea y siga todas las reglas de

seguridad e instrucciones de operación antes de

usar este producto. El no hacerlo puede causar

lesiones graves.

Manual de instrucciones

PR5020

Guía de inicio rápido

Mezcle 2,6 onzas de aceite completamente sintético de doble ciclo con

1 galón de gasolina para obtener una mezcla de 50:1. Agítelo bien.

Vierta en el tanque de combustible.

AVISO: No utilice combustibles alternativos como mezclas de etanol

superiores al 10 % en volumen (E-15, E-85) o cualquier combustible

mezclado con metanol.

Agregue aceite de espada y cadena

al depósito de aceite hasta que se

llene.

Empuje el guardamanos hacia delante

para asegurarse de que el freno de

cadena esté bloqueado.

Presione el bulbo cebador (bomba de

combustible) lentamente 10 veces.

Tire de la palanca del estrangulador

azul hacia afuera hasta que salga

completamente.

Coloque su pie derecho en el mango trasero

FRPRVHPXHVWUDHQOD¿JXUD&RQVX

mano derecha, tire fuertemente la cuerda

de arranque hasta que la máquina intente

arrancar o un máximo de 5 veces.

Empuje la palanca del estrangulador

azul hasta la mitad de la posición de

estrangulamiento.

Tire de la cuerda de arranque hasta que el

motor arranque.

Deje que el motor se caliente durante 30

segundos.

Asegúrese de que del freno de cadena

esté desbloqueado tirando hacia atrás

el guardamanos.

Apriete el gatillo del acelerador a

ralentí normal. La motosierra ya está

lista para ser utilizada.

Presione el interruptor rojo a la

posición de parada cuando termine

de usar la sierra.

ARRANCAR UN MOTOR EN CALIENTE

4 + 5 + 7 + 8

NOTA: Si el producto no se reinicia, el problema puede ser producto

del combustible sobrecalentado. Para solucionar este problema,

intente el siguiente procedimiento:

1. Coloque el producto en un área fresca alejada de la luz directa

del sol.

2. Deje que el producto se enfríe durante al menos 20 minutos.

3. Presione el bulbo cebador (purga de aire) repetidamente durante

10 a 15 segundos.

4. Siga el procedimiento de arranque en frío.

Repita este procedimiento si el problema persiste.

NOTA: Siempre utilice combustible estacional y reduzca el tiempo de

funcionamiento durante climas inusualmente cálidos.

IMPORTANTE:

• Nunca deje que la cadena de su sierra entre en contacto con el

VXHORRODVXFLHGDGGXUDQWHHOIXQFLRQDPLHQWR(VWRGHVD¿ODUi

completamente su cadena y requerirá la instalación de una nueva.

• Siempre compruebe la tensión de la cadena antes de arrancar la

motosierra. Revise la tensión de una nueva cadena después de los

primeros 15 minutos de funcionamiento. Consulte el manual para

obtener instrucciones para ajustar la tensión de la cadena..

NOTA: El producto puede ser levemente distinto al

DUWLFXORTXHVHPXHVWUDHQOD¿JXUD

La page charge ...

Poulan Pro PR5020 Le manuel du propriétaire

Marque: Poulan Pro

Modèle: PR5020

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Poulan Pro PR5020 Owner's manual

Poulan Pro PR5020 Le manuel du propriétaire

Poulan Pro PR5020 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents