Signature Kitchen Suite SKSUD2402P Guide d'installation

INSTALLATION MANUAL

BUILT-IN REFRIGERATOR

Read this installation manual thoroughly before installing the appliance and

keep it handy for reference at all times.

ENGLISH

SKSUD2402P / SKSUW2401P

MFL67410830

Rev.01_071423

www.signaturekitchensuite.com

en-us_main.book.book Page 1 Friday, July 14, 2023 11:13 AM

TABLE OF CONTENTS

2

3 IMPORTANT SAFETY

INSTRUCTIONS

3 WARNING

3 Installation

3 Electrical Connection

4CAUTION

4 General

5 INSTALLATION

5 Before Installation

5 Choosing the Install Location

5 Anti-tip Devices

5 Enclosure

5Floor

5 Electrical Requirements

6 Grounding

6 Cutout Dimensions

7 Installation Clearances

8 Required Accessories and Tools

8 Accessories

8Tools

9 Product Dimensions

11 Custom Panel Dimensions

12 Moving Appliance into Enclosure

12 Installing the Anti-tip Brackets

13 Protecting Edges of Enclosure

13 Installing Appliance in Enclosure

15 Leveling and Securing the Appliance

15 Aligning and Leveling the Appliance

17 Attaching Appliance to Enclosure

18 Attaching the Toe Kick Panel

20 Panels and Trim

20 Installing Door Panels

22 Adjusting Door Panels

22 Installing Door Trim

26 Reversing the Door

27 Attaching the Badge

28 Inserting the Link Assembly

en-us_main.book.book Page 2 Friday, July 14, 2023 11:13 AM

3IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

WARNING

• TIP-OVER HAZARD

- The appliance is very heavy. If it tips over, it could cause damage, serious injury or death. Do not open

the doors or drawers before the appliance is securely installed.

- Use two or more people to move and install the refrigerator. To prevent the refrigerator from tipping

over, install anti-tip brackets (provided). Failure to follow the refrigerator installation instructions can

result in serious injury or death.

• To reduce the risk of fire, electric shock, or personal injury when using the product, basic safety

precautions should be followed, including the following. Read all instructions before using this

appliance.

Installation

• These products are not designed to be used as freestanding units. Doing so will result in a risk of tipover,

personal injury, and product or property damage.

• Do not install the refrigerator near a gas stove, water heater or other source of ignition that may

possibly leak gas. Do not install product in direct sunlight. Install the product in a well ventilated area.

• Ensure that enclosure dimensions allow for sufficient air circulation at the sides and back of the product.

Do not block the front air inlet. Failure to follow these instructions may cause product malfunction.

• Enclosure must be constructed of materials which are strong enough to avoid damage during

installation and frequent use.

• Cabinet materials must be able to withstand the heat and humidity produced during product operation

and use without twisting or deforming.

• Install the product on a firm, level surface that can support the weight of the product without bending.

The product must be level both horizontally and vertically.

• Keep children away from area during installation.

• Do not use an extension cord or power strip with this product.

• Do not install the refrigerator in a damp location or where it will be exposed to running water.

Deterioration of the insulation on electrical parts may result, causing risk of electric shock.

• Connect to potable water only. Non-potable water can cause health risks.

Electrical Connection

•If connected to a circuit protected by fuses, use time delay fuse.

•Use a dedicated outlet.

- Plugging several devices into one outlet may cause a fire.

•Plug in the power plug with the power cord facing downward.

- Failure to do so could damage the plug or cord, resulting in fire or electric shock.

•When installing or moving the refrigerator, be careful not to roll over or damage the power cord.

Do not squeeze or crush the cord or plug when pushing the refrigerator in.

- Doing so could result in fire or electric shock.

•Do not allow the power cord to be bent, crushed, or damaged. Do not run the power cord under

heavy objects like furniture, other appliances, or through high-traffic areas.

- Doing so may damage the power cord and result in fire or electric shock.

•Do not extend or modify the length of the power cord.

- Use only an exact factory replacement part to avoid electrical issues, fire, or electric shock.

en-us_main.book.book Page 3 Friday, July 14, 2023 11:13 AM

4IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

•Turn off the power before cleaning or moving the refrigerator.

- Failure to do so may cause electric shock or injury.

- Press the POWER button for 3 seconds to turn off the power at the display panel.

•Do not pull out the cord or touch the power plug with wet hands.

- Doing so may cause electric shock or injury.

•Remove water or dust from the power plug and insert it securely into the wall socket.

- Dust, water, or a loose connection may cause a fire or electric shock.

•Do not unplug the refrigerator by pulling on the cord.

- Doing so may cause an electric shock or a short circuit resulting in a fire.

•Do not use the power cord or the power plug if it is damaged or if the outlet is damaged.

- Doing so may cause an electric shock or a short circuit resulting in a fire.

•Wait for 5 minutes or longer when reconnecting the plug or turning the power back on.

- Give the compressor time to cycle before restarting.

•If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a

similarly qualified person in order to avoid a hazard.

CAUTION

•Do not stick your hands under the refrigerator.

- Sharp edges, fans, and wires may cause an injury.

•Save these instructions for the local inspector's use.

•Observe all governing codes and ordinances.

•Installer: Leave these instructions with the consumer.

•Consumer: Keep these instructions with the owner's manual for future reference.

General

These installation instructions are intended for use by qualified installers. All connections for water,

electrical power and grounding must comply with local codes and ordinances and be made by licensed

personnel when required. In the absence of a local code:

• In the U.S.A., in accordance with the National Electric Code, ANSI/NFPA70 – latest edition/State and

Municipal codes and/or local codes.

• In Canada, in accordance with the Canadian Electric Code C22.1 – latest edition/Provincial and Municipal

codes and/or local codes.

en-us_main.book.book Page 4 Friday, July 14, 2023 11:13 AM

5INSTALLATION

ENGLISH

INSTALLATION

Before Installation

WARNING

• Do not store or install the appliance where it will

be exposed to:

- outside weather

- water damage

- temperatures under 32 ℉ (0 ℃)

Choosing the Install Location

Temperature and Humidity

• The appliance should be installed in a dry, well

ventilated area.

• The ambient temperature should stay between

55 ℉ (13 ℃) and 110 ℉ (43 ℃), to avoid

malfunctions.

• Do not install product where it will be exposed to

direct sunlight or near a heat source, such as an

oven or radiator.

Anti-tip Devices

WARNING

• Tip Hazard

- The appliance is very heavy and may tip over if

the door is opened before the appliance is

securely installed.

- Install the supplied anti-tip brackets to prevent

the appliance from tipping. The safest method

of installing the appliance in a stable position

is to use the supplied anti-tip devices.

- Do not open the appliance door unless it is still

on the pallet or the anti-tip brackets are

engaged.

• If the enclosure is sturdy enough, attaching the

appliance to the upper and side walls of the

enclosure may provide additional stability, as

long as the enclosure is firmly connected to the

back wall. If in doubt, contact an architect or

structural engineer.

Enclosure

• The panel above the appliance must be made

from a solid material (not MDF) and at least 5/8"

(16 mm) thick.

• The side walls of the cavity or enclosure must be

flush.

• The front 4 inches (100 mm) of the interior

surface (furniture return) will be visible when

doors are open. Make sure this area is finished

to at least 4 inches deep.

• Follow the specifications for the installation

enclosure to ensure a trouble free installation.

• Above all, the enclosure cannot be out of square.

Use a spirit level or measure the diagonals of the

opening to make sure corners are square.

• The appliance is attached at the sides and the

top to either the enclosure or to adjacent

cabinets. Make sure the enclosure or the

adjacent cabinets are securely connected to the

floor or wall structures.

Floor

WARNING

• The floor in the installation area must be firm,

level, and rigid for safe installation and best

performance.

• Do not install the appliance on a platform or

raised structure.

• The structure underneath the appliance must be

able to support the weight of the appliance

without tilting or flexing.

• For best performance and to avoid leakage, level

the appliance.

Electrical Requirements

WARNING

• Electrical Shock Hazard

- Plug into a grounded 3-prong outlet.

- Do not remove ground prong.

- Do not use an adapter.

- Do not use an extension cord.

• Failure to follow these instructions can result in

death, fire, or electrical shock.

• Follow all state and local codes or NEC.

• The appliance comes with a UL listed 3-wire

power supply cord.

• The appliance requires a 3-wire receptacle.

en-us_main.book.book Page 5 Friday, July 14, 2023 11:13 AM

6INSTALLATION

WARNING

• The receptacle must be installed by a licensed

electrician only.

Grounding

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of

least resistance for the electric current.

WARNING

• Improper connection of the equipment

grounding conductor may result in electric

shock. Have the appliance checked by a qualified

electrician or service technician if you are in

doubt as to whether the appliance has been

properly grounded.

NOTE

• Some local regulations may require a separate

ground. In such cases, the required ground wire,

clamp and screw are available as a separate

accessory and must be purchased separately.

• Never ground the appliance to plastic plumbing

lines, gas lines or water pipes.

Cutout Dimensions

CAUTION

• The anti-tip bracket should be firmly fixed to a

concrete wall/wood with strength of 15 t or

greater, or a wall with equivalent strength. (The

structure where the bracket is fixed should be a

solid structure that can withstand a force of 70

kgf or greater.)

• Before installing the appliance, make sure that

the enclosure is the correct size. For the

appliance to operate properly, the notch in the

bottom front plate must be aligned with the

center of the appliance.

• A minimum 4" (101 mm) finished return that

matches the cabinet exterior is recommended

on all sides and at the top of the cutout opening.

The shaded area will be visible after installation.

-SKSUD2402P SKSUW2401P

A224" (610 mm)

B224" (610 mm)

C234 1/2" (876 mm)

D 4" (101 mm)

E 23 11/16" (602 mm)

F 30 5/16" (770 mm)

A

B

C

D

E

F

SKSUD2402P

SKSUW2401P

A

C

D

F

B

E

en-us_main.book.book Page 6 Friday, July 14, 2023 11:13 AM

7INSTALLATION

ENGLISH

Electrical

• A 115 V, 60 Hz, 15 amp power supply is required.

An individual, properly grounded branch circuit

or circuit breaker is recommended. Install a

properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be

located on rear wall as shown.

• When installing a single product, use a single

outlet.

NOTE

• GFCI (ground fault circuit interrupter) is not

recommended.

Installation Clearances

Model: SKSUD2402P

* Side clearance at cabinet

** Side clearance at front panel

Model: SKSUW2401P

* Right hand hinge installation shown. When

reversing the door, the hinge and handle side

clearances also reverse.

** Side clearance at front panel

Top View (Door Closed)

Top View (Door Open 90°)

A

B

C* C*

D** D** E

F

-Dimensions and Clearances

A224" (610 mm)

B 23 7/16" (595 mm)

C 5/16" (7.5 mm) min.

D 3/16" (4 mm)

E 18" (457 mm) with panel

F 23 11/16" (602 mm) with panel

A

B

C*

D** D**

C*

E

Door

Case

Panel

D**

C*

Case

Door

Hinge

D**

en-us_main.book.book Page 7 Friday, July 14, 2023 11:13 AM

8INSTALLATION

Top View (Door Open 115°)

NOTE

• Door Swing Clearances

- The installation must allow for clearances to

adjacent walls or cabinets. This wine

refrigerator is equipped with a 2-position door

stop. The factory-set 115° door swing can be

adjusted to 90° if clearance to adjacent

cabinets or walls is restricted.

• Door Handle Clearances

- The door handle depth must be added to the

dimension as noted to determine the total

clearances required from adjacent cabinets or

walls. This clearance will vary depending on

the custom handle used. When using the

Stainless Steel Door Panel Kit w/ Stainless Steel

Handle, the door handle clearance with door

open 115° is 11 3/4" (298 mm).

Required Accessories and

Tools

Accessories

Supplied Accessories

• Installation instructions

• Operating instructions

• Installation kit

NOTE

• In addition to the quantity required for installing

the appliance, spare screws may be provided.

Other

• Dolly, hand truck

• Drill for drilling holes in wall or floor.

• Drill bits in various sizes and suitable for

materials

• Wood screws in different sizes

• Thin plywood sheet, particle board or cardboard

to protect the floor from damage

• Suitable material for covering and protecting

furniture (e.g. protective sheets)

• Adhesive tape

Tools

-Dimensions and Clearances

A224" (610 mm)

B 23 7/16" (595 mm)

CHandle Side 1/8" (2.5 mm) min.

Hinge Side 1/2" (12.5 mm) min.

D 3/16" (4 mm)

E 23 11/16" (602 mm) with panel

F1/4" (6.5 mm)

Case

Door

Hinge

F

Screw Size No. Used for

5H x

45L 6 Anti-tip bracket

4D x

14L 10 Anti-tip bracket (6)

Enclosure (4)

4D x

6L 4Enclosure

4D x

12L 12 Door panel

Cordless screwdriver

Torx bit T20, T30 and

magnetic holder

Torx screwdriver T20, T30

3/8" (10 mm) hex nut driver

Various drill bits

en-us_main.book.book Page 8 Friday, July 14, 2023 11:13 AM

9INSTALLATION

ENGLISH

Product Dimensions

The following installation instructions describe the

installation steps for various appliance types.

The diagrams may be a general representation of

your appliance.

Particular reference is made to special installation

steps for individual appliance types.

Product Dimensions

Model: SKSUD2402P

• Front View

• Side View

* Depth with 3/4" (19 mm) drawer panel

** Depth with drawers (no panel)

*** Unit depth without drawers

Multigrip pliers

Adjustable wrench

Cutter with adustable blade

Metal tape measure, folding

rule

Square

Level, length 2" (60 cm) and 4'

(1.2 m)

Saw to cut top trim pieces (for

retrofit installation only)

A

B

C

D

E

-Dimensions

A23 11/16" (602 mm) with panel

23 7/16" (595 mm) without panel

B 15" (381 mm)

C 1/4" (7 mm)

D 4" (101 mm)

E34 1/4" (870 mm) min.

34 5/8" (880 mm) max.

F 23 1/4" (590 mm)

G 22 1/2" (571 mm)

H 20 1/2" (520 mm)

I33 3/16" (843 mm) min.

33 9/16" (853 mm) max.

J 5" (128 mm)

F*

G**

H***

I

J

D

en-us_main.book.book Page 9 Friday, July 14, 2023 11:13 AM

10 INSTALLATION

Model: SKSUW2401P

• Front View

• Side View

* Depth with 3/4" (19 mm) drawer panel

** Depth with door (no panel)

*** Unit depth without door

• Top View (Door Open 90º)

• Top View (Door Open 115º)

* Door handle must be added to this dimension.

** Varies depending on the thickness of the

custom cabinet panel. The door panels in the

optional Signature Kitchen Suite stainless steel

door panel kit are 3/4" (19 mm) thick.

-Dimensions

A 23 11/16" (602 mm) with panel

B34 1/4" (870 mm) min.

34 5/8" (880 mm) max.

C 4" (101 mm)

D 23 5/8" (600 mm)

E 22 7/8" (581 mm)

F 20 7/8" (530 mm)

G33 3/16" (843 mm) min.

33 9/16" (853 mm) max.

H 5" (128 mm)

A

B

C

D*

E**

F***

G

H

C

-Dimensions

I 23 7/16" (595 mm)

J 20 7/8" (530 mm)

K 26 1/8" (663 mm)

L 10 1/2" (266 mm)

M 24 3/8" (620 mm)

I

J

K

I

L*

M

N**

en-us_main.book.book Page 10 Friday, July 14, 2023 11:13 AM

11INSTALLATION

ENGLISH

NOTE

• This unit is designed to be customized with a

decorative panel. A field-installed custom door

panel or an optional Stainless Steel Panel Kit is

required.

•For Custom Panels: Use templates provided

with units to pre-drill holes for mounting panel

brackets (provided with unit). Adjustment screws

and instructions are also provided with units.

Custom Panel Dimensions

3/4" (19 mm) Custom panel dimensions

– Flush installation

• 24-inch undercounter convertible drawer

refrigerator

NOTE

• The custom panel dimensions are the same for

the upper and lower drawers.

• 24-inch built-in undercounter wine refrigerator

SKS door handle installation

dimensions of custom panel

• 24-inch undercounter convertible drawer

refrigerator

• 24-inch built-in undercounter wine refrigerator

N 3/4" (19 mm)

-Dimensions

A 23 11/16" (602 mm)

B 15" (381 mm)

-Dimensions

A

B

-Dimensions

C 23 1/16" (602 mm)

D 3 11/32" (84.9 mm)

E 4 15/16" (124.9 mm)

F 30 9/32" (769 mm)

F

C

D

E

D

en-us_main.book.book Page 11 Friday, July 14, 2023 11:13 AM

12 INSTALLATION

Optional Accessories

•SKSUK240DS - Stainless Steel Panel and

Handle Kit for 24-inch Undercounter Drawer

Refrigerator

- This unit can be installed with an optional

Stainless Steel Panel Kit. Kit includes two

drawer panels and two handles.

•SKSUK240WS - Stainless Steel Panel and

Handle Kit for 24-inch Undercounter Wine

Refrigerator

- This unit can be installed with an optional

Stainless Steel Panel Kit. Kit includes door

panel and handle.

•SKSHK230HS - Handles for use with custom

panel

- 22 3/4" (578 mm) medium brushed aluminum

handle

Moving Appliance into

Enclosure

Installing the Anti-tip Brackets

WARNING

• To avoid injury or damage, check for electrical

wires or plumbing in walls before drilling or

installing screws.

• The anti-tip bracket should be firmly fixed to a

concrete wall/wood with strength of 15 t or

greater, or a wall with equivalent strength. (The

structure where the bracket is fixed should be a

solid structure that can withstand a force of 70

kgf or greater.)

Install the anti-tip brackets at the rear of the

enclosure, locating the brackets based on stud

locations and product and enclosure dimensions.

NOTE

• Brackets must be attached as shown below. The

brackets could fail to prevent tipover of the unit

if installed in an alternate orientation.

-Dimensions

A 3 3/4'' (94.5 mm)

B 2 7/16'' (62.4 mm)

C 1 7/16'' (37 mm)

D 15/16'' (24.4 mm)

EΦ 3/16'' (4.8 mm)

F 7'' (178 mm)

G 1 1/4'' (57.9 mm)

-Dimensions

A33 3/16" (843 mm) min.

33 9/16" (853 mm) max.

B 2 3/8" (60 mm)

C 3 3/4" (90 mm)

A

B

C

Anti-Tip Bracket x 2

en-us_main.book.book Page 12 Friday, July 14, 2023 11:13 AM

13INSTALLATION

ENGLISH

• Use A type or B type screws. (Recommended:

Concrete wall ~ A Type, Wood wall ~ B Type) Protecting Edges of Enclosure

To protect the front edges of the enclosure, tape

thin cardboard or some other protective material

around the edges.

aProtective cover

Installing Appliance in Enclosure

WARNING

• Use 2 or more people when installing the appliance. Take care when moving the appliance. It is very

heavy and prone to tipping when not secured.

CAUTION

• Take care to avoid damaging the water line or power cord when moving the appliance into the

enclosure.

• Before moving the unit into position, secure the door/drawers closed and protect any finished flooring.

• Use an appliance dolly to move the unit near the opening.

• The front leveling legs are extended below the front rollers to improve stability during placement. Once

the unit is placed in front of the opening, completely retract the front leveling legs to allow the unit to be

rolled into position. Front and rear leveling legs can be adjusted from the front once the unit is

positioned.

• If the unit has been on its back or side, it must stand upright for a minimum of 24 hours before turning

on the power.

en-us_main.book.book Page 13 Friday, July 14, 2023 11:13 AM

14 INSTALLATION

CAUTION

• After the appliance is rolled into position, verify that the anti-tip brackets are properly engaged.

1 Remove the base panel.

2 Retract the leveling legs so the appliance can be wheeled forward.

3 Plug the power cord into the outlet.

4 Tie a long string around the middle of the power cord. Feed the string over the top of the appliance,

pull it until the power cord is held high off the ground, then tape the string to the front of the

appliance to hold the power cord off the ground. Do not pinch or strain the power cord. Make sure it

is still plugged in.

5 Carefully move the appliance into the enclosure, making sure not to pinch thepower cord or water line

under or behind the appliance.

6 Remove the string from the power cord and the edge protection on the enclosure.

2

1

3

4

5

4

en-us_main.book.book Page 14 Friday, July 14, 2023 11:13 AM

15INSTALLATION

ENGLISH

Leveling and Securing the Appliance

Aligning and Leveling the Appliance

• Depth Adjustment

- Adjust the depth of the unit in the enclosure so the door panels will fit flush with the surrounding

cabinetry. Use the gauge tool provided for a precise fit.

• Height Adjustment

- The front and rear leveling legs can both be adjusted from the front.

• Leveling

- Once the appliance is aligned properly in the enclosure, level it using the front and rear leveling legs.

1 Use a Phillips screwdriver and wrench to extend the front and rear leveling legs until they are in firm

contact with the floor.

2 Turn the screws as shown above to raise the appliance. Turn the screws in the opposite direction to

lower the appliance.

3 Make sure the weight of the refrigerator is carried on the legs, not the wheels.

Rear

adjustment

Front

adjustment

)URQW

DGMXVWPHQW

5HDU

DGMXVWPHQW

Left

Rear

Raise

Product

Raise

Product

RearFront Front

Right

en-us_main.book.book Page 15 Friday, July 14, 2023 11:13 AM

16 INSTALLATION

4 Use a smartphone leveling app or place a carpenter's level on the top and sides of the appliance to

check that it is level and plumb. Or use the provided gauge tool to measure the distance of the

bottom edge of the appliance from the floor at the front corners.

WARNING

• To reduce the possibility of the unit tipping forward, the front leveling legs must be in contact with the

floor.

CAUTION

• If using a power drill, use the lowest torque setting.

• Leave at least 3/8 inch (10 mm) between the top front of the appliance and the top of the enclosure to fit

the top filler strip.

• Do not exceed 20 inch-pounds (2.25 Nm) of torque.

• 20 revolutions equal 1/16” (2 mm) of height adjustment.

en-us_main.book.book Page 16 Friday, July 14, 2023 11:13 AM

17INSTALLATION

ENGLISH

Attaching Appliance to Enclosure

• Tighten the side fixing bracket to the bottom left and right sides of the cabinet using the B type and C-1

type screws.

• Use the B type screw to fix the bracket to the cabinet and use the C-1 type screw to attach the bracket to

the appliance.

• If there is not enough space to tighten the screw on the side by the baseboard, attach the bracket to the

bottom of the adjoining cabinet.

•If the mounting bracket is attached to the cabinet first:

1 Attach the bracket to the cabinet using a B type screw.

2 Insert the appliance, level the appliance with the adjoining cabinet, and secure the appliance by

extending the front and rear legs.

en-us_main.book.book Page 17 Friday, July 14, 2023 11:13 AM

18 INSTALLATION

3 After securing the appliance, attach the bracket to the refrigerator using a C-1 type screw.

Attaching the Toe Kick Panel

CAUTION

• Do not close the air vent in the bottom cover of the appliance.

1 Use a screw a to attach the bottom cover to the appliance.

2 Attach the Smart Diagnosis label b in the location shown.

-Dimensions

A 6 11/16" (170 mm)

B 5 5/16" (135 mm)

Front

Floor

A

1

2

3

B

en-us_main.book.book Page 18 Friday, July 14, 2023 11:13 AM

19INSTALLATION

ENGLISH

NOTE

• The Wi-Fi transmission and reception unit is located on the baseboard, so the reception may depend on

the baseboard material.

• Finishing the baseboard installation

- If the position (depth from the front) of the cabinet baseboard is different from the position of the

appliance baseboard, adjust the cabinet baseboard so that it is aligned with the position of the

appliance baseboard.

• To adjust the baseboard

- Pull the cabinet baseboard forward and align it with the refrigerator baseboard.

- After adjusting the baseboard

en-us_main.book.book Page 19 Friday, July 14, 2023 11:13 AM

20 INSTALLATION

Panels and Trim

Installing Door Panels

The door panel should be installed first, followed by the upper then lower drawer panels, if needed.

1 Place the door panel face down on a protected surface.

2 Locate the correct side of the door panel template for your product and position the template flush

with the top and left sides of the panel.

3 Use the template to mark the correct screw locations on the back of the panel.

4 Slide the template to the right so it is flush with the top and right sides of the panel.

5 Use the template to mark the correct screw locations on the back of the panel.

6 On refrigerator/freezer columns, begin inserting a #8 x 1/2" screw into the fifth hole from the top on

each side. On wine columns, use the third hole from the top. Stop when the screws are 3/16" (4 mm)

proud of the panel. These will be the support screws during the panel installation.

en-us_main.book.book Page 20 Friday, July 14, 2023 11:13 AM

La page charge ...

Signature Kitchen Suite SKSUD2402P Guide d'installation

Signature Kitchen Suite SKSUD2402P Guide d'installation

dans d''autres langues

Documents connexes

Autres documents