Yes SRFB27W3 Manuel utilisateur

OWNER’S MANUAL

FRENCH DOOR

REFRIGERATOR

ENGLISH

SRFB27S*, SRFB27W*

MFL69497053

Rev.02_070423

www.lg.com

Read this owner’s manual thoroughly before operating the appliance

and keep it handy for reference at all times. This abridged owner's

manual addresses user safety, precautions, and installation

information.

To view the complete owner's manual, you may:

1. Online manual: Visit the LG website at: http://gscs-manual.lge.com/

Total/HQ/GatewayPage/main.html or scan the QR code above; or

2. Printable PDF manual: Visit lg.com and search for your model

number; or

3. Call or write to customer service as provided in your Limited

Warranty.

Scan to see the online manual.

en-us_main.book.book Page 1 Monday, July 3, 2023 9:26 AM

TABLE OF CONTENTS

2

3 IMPORTANT SAFETY

INSTRUCTIONS

3 READ ALL INSTRUCTIONS BEFORE USE

3WARNING

6CAUTION

8 PRODUCT OVERVIEW

8 Product Features

9 INSTALLATION

9 Before Installing

10 Choosing the Proper Location

12 Removing/Assembling Handles

13 Removing/Assembling Doors and Drawers

18 Connecting Refrigerator to Water Supply

20 Leveling and Door Alignment

22 Turning on the Power

23 OPERATION

23 Online Owner's Manual

24 Control Panel

27 InstaView

27 Sabbath Mode

28 Ice and Water Dispenser

28 Automatic Icemaker

30 Full-Convert DrawerTM

32 SMART FUNCTIONS

32 LG ThinQ Application

34 Smart Grid Function

35 MAINTENANCE

35 Cleaning

35 Air Filter

36 Water Filter

41 TROUBLESHOOTING

41 FAQs

42 Before Calling for Service

43 LIMITED WARRANTY

43 USA

47 Canada

en-us_main.book.book Page 2 Monday, July 3, 2023 9:26 AM

3IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Safety Messages

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what may happen if the instructions are not followed.

WARNING

• To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this

product, follow basic precautions, including the following:

Installation

• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including

the use of long-sleeved gloves and safety glasses.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged cord or plug.

• Only connect this product to a dedicated grounded electrical outlet rated for use with this product (115

V, 60 Hz, AC only). It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard

3-prong wall outlet.

• Do not use an outlet that can be turned off with a switch. Do not use an extension cord.

• The appliance must be positioned for easy access to a power source.

• When moving the refrigerator, be careful not to roll over or damage the power cord.

• Contact an authorized service center when installing or relocating the refrigerator.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

• Do not install the refrigerator in a damp or dusty place where insulation on electrical parts may

deteriorate.

• Do not place the refrigerator in direct sunlight or expose it to the heat from heating appliances such as

stoves or heaters.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages

will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

en-us_main.book.book Page 3 Monday, July 3, 2023 9:26 AM

4IMPORTANT SAFETY INSTRUCTIONS

• Do not bend or pinch the power cord excessively or place heavy objects on it.

Operation

• This appliance is intended to be used in household and similar applications such as:

- staff kitchen areas in shops, offices and other working environments;

- farm houses and by clients in hotels, motels and other residential type environments;

- bed and breakfast type environments;

- catering and similar non-retail applications.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

• This product is not to be used for special purposes such as the storage of medicine or test materials or

for use on ships, etc.

• DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the

refrigerator. They could damage the refrigerator and seriously injure themselves.

• Do not allow children to climb into the refrigerator. They could be trapped and suffocated.

• Children should be supervised to ensure that they do not play with the refrigerator.

• Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small.

Be careful closing doors when children are nearby.

• Do not touch frozen food or the metal parts in the freezer compartment with wet or damp hands. Doing

so may cause frostbite.

• Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health hazard.

• Do not use an adapter plug or plug the power plug into a multi-outlet extension cord.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

• Do not operate the refrigerator or touch the power cord with wet hands.

• Do not modify or extend the power cord.

• Do not use an uncertified power outlet. Do not plug appliance into a damaged wall outlet.

• Do not put hands, feet or other objects into the air vents or bottom of the refrigerator. Doing so could

result in personal injury or electric shock.

• In the event of a gas leak (propane/LPG), ensure the area is adequately ventilated and contact an

authorized service center before resuming use. Do not touch the refrigerator or power cord of the

refrigerator.

• Disconnect the power cord immediately and contact an authorized service center if there is a strange

noise, odor, or smoke coming from the appliance.

• Do not use any fuse (such as copper, steel wire, etc.) other than a standard fuse.

• Do not put animals inside the appliance.

• Do not place heavy or fragile objects, liquid filled containers, combustible substances, or flammable

objects (such as candles and lamps) on the appliance.

• If connected to a circuit protected by fuses, use time delay fuse.

• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

• Do not use mechanical devices or other means to accelerate the defrosting process, other than those

recommended by the manufacturer.

• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are

of the type recommended by the manufacturer.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

en-us_main.book.book Page 4 Monday, July 3, 2023 9:26 AM

5IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

• If the Durabase divider is removed, there is enough open space for children or pets to crawl inside. To

prevent accidental child and pet entrapment or suffocation risk, DO NOT allow children or pets to touch

or go near the drawer.

• Do not damage the refrigerant circuit.

• This appliance incorporates an earth connection for functional purposes.

• Connect to potable water supply only.

- If connected to a water supply, connect to a potable water supply only.

• Fill with potable water only.

- If using an icemaker or dispenser water tank, make sure to fill it with potable water only.

Maintenance

• Do not use a hair dryer to dry the inside of the refrigerator.

• Do not light a candle to remove odors in the refrigerator.

• In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure the area is

adequately ventilated and contact an authorized service center.

• Keep flammable materials and vapors, such as gasoline, away from the refrigerator.

• Unplug the power plug before cleaning or repairing the refrigerator.

• The refrigerator and freezer compartment lights are interior LED lighting, and service should be

performed by a qualified technician.

• Unplug the power plug immediately in the event of a blackout or thunderstorm.

• Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

• Do not store glass containers or soda in the freezer compartment. Contents may expand when frozen,

break the container and cause injury.

• Do not store, disassemble or repair the appliance yourself or allow unqualified personnel to do so.

Disposal

• Risk of child entrapment. Junked or abandoned refrigerators are dangerous, even if they are sitting for

only a few days. When disposing of the refrigerator, remove the packing materials from the door or take

off the doors but leave the shelves in place so that children may not easily climb inside.

• If disposing of a refrigerator, make sure the refrigerant and insulation foam are removed for proper

disposal by a qualified servicer. If you release the refrigerant or throw away the insulation foam, you

may be fined or imprisoned in accordance with the relevant environmental law. Insulation foam contains

flammable blowing gas.

• When discarding the appliance, remove the door gasket while leaving the shelves and bins in place, and

keep children away from the appliance.

Grounding Instructions

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check

with a qualified electrician or service personnel if you are in doubt whether the appliance is properly

grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

• Have a certified electrician check the wall outlet and wiring for proper grounding.

• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight

out from the outlet. Failure to do so may damage the power cord, resulting in a risk of fire and electric

shock.

en-us_main.book.book Page 5 Monday, July 3, 2023 9:26 AM

6IMPORTANT SAFETY INSTRUCTIONS

Risk of Fire and Flammable Materials

CAUTION

• To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or

property when using this product, follow basic precautions, including the following:

Installation

• Do not install the refrigerator where there may be a danger of the unit falling.

• The refrigerator must be properly installed in accordance with the Installation Instructions.

• This appliance does not require changes in installation or use based on altitude.

Operation

• This appliance is intended to be used only in domestic and similar applications.

• Do not scratch the refrigerator with a sharp object or use a detergent that contains alcohol, a flammable

liquid or an abrasive when removing any tape or adhesive from the refrigerator. Remove adhesive

residue by wiping it off with your thumb or dish detergent.

• Do not peel off the model or serial number label or the technical information on the rear surface of the

refrigerator.

• Putting food in the refrigerator before it has cooled could cause the food to spoil, or a bad odor to

remain inside the refrigerator.

• Keep hands and tools out of the ice compartment door and dispenser chute. Failure to do so may result

in damage or personal injury.

• Keep the ice compartment door closed tightly. If the ice compartment door is not closed tightly, the cold

air in the ice bin will freeze food in the refrigerator compartment. This could also cause the icemaker to

stop producing ice.

• Storing cans or other items in the ice bin will damage the icemaker.

• Store only ice in the ice bin. Do not store ice scooping tools or other items in the ice bin.

• Ice may overflow when removing or assembling the ice bin. Remove any ice in the bin area before

assembling the ice bin.

• Make sure that the ice bin is assembled in the correct orientation front to back.

• Models with two ice bins in the freezer:

- The Craft Ice bin is located on the left and the Mini Cubed Ice bin is located on the right. Do not

change the positions of the two ice bins.

- Do not store Craft Ice in the Mini Cubed Ice bin or Mini Cubed Ice in the Craft Ice bin.

This appliance contains a small amount of isobutane refrigerant (R600a), which is combustible.

When transporting and installing the appliance, care should be taken to ensure that no parts

of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or

cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of

ignition and air out the room in which the appliance is standing for several minutes.

In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating

circuit occurs, the size of the room in which the appliance may be sited depends on the

amount of refrigerant used. The room must be 10.8 square feet (1 square meter) in size for

every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your

particular appliance is shown on the identification plate inside the appliance. Never start up an

appliance showing any signs of damage. If in doubt, consult your dealer.

en-us_main.book.book Page 6 Monday, July 3, 2023 9:26 AM

7IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

SAVE THESE INSTRUCTIONS

• Never use thin crystal glasses or containers to collect ice. Such containers may chip or break resulting in

glass fragments in the ice.

• Only qualified service personnel from an LG Electronics service center should disassemble or repair the

icemaker.

• When handling the ice bin, keep hands away from the icemaker tray area to avoid personal injury.

• Avoid touching the auto shutoff (feeler arm) when replacing the ice bin. See the label on the ice

compartment door for details.

• Do not use aerosols near the refrigerator.

• Do not strike or apply excessive force to any glass surface. Do not touch glass surfaces if they are

cracked or broken.

• Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or

personal injury if items are removed with excessive force.

• Do not store glass containers in the freezer. Contents may expand when frozen, break the container and

cause injury.

• Glass shelves are heavy. Use special care when removing them.

• Do not clean glass shelves with warm water while they are cold. Shelves may break if exposed to sudden

temperature changes or impact.

• Make sure that shelves are level from one side to the other. Failure to do so may result in the shelf falling

or spilled food.

• Regularly detach and wash the storage bins and shelves; they can become easily contaminated by food.

• Do not apply excessive force while detaching or assembling the storage bins.

• Do not use the dishwasher to clean the storage bins and shelves.

Maintenance

• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.

• Remove foreign objects (such as dust and water) off the prongs of the power plug and contact areas. Do

not use a wet or damp cloth when cleaning the plug.

• Do not spray water directly on the inside or outside of the refrigerator.

• Do not clean glass shelves or covers with warm water when they are cold. They may break if exposed to

sudden temperature changes.

en-us_main.book.book Page 7 Monday, July 3, 2023 9:26 AM

8PRODUCT OVERVIEW

PRODUCT OVERVIEW

Product Features

The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Electrical requirements: 115 V, 60 Hz

Min. / Max. water pressure: 20 - 120 psi (138 - 827 kPa)

Model Description Net weight

SRFB27S* Counter-depth, French Door Refrigerator, Bottom Freezer, Internal

Water Dispenser

254 lb (115 kg)

SRFB27W* Counter-depth, French Door Refrigerator, Bottom Freezer, Internal

Water Dispenser

256 lb (116 kg)

en-us_main.book.book Page 8 Monday, July 3, 2023 9:26 AM

9INSTALLATION

ENGLISH

INSTALLATION

Before Installing

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to

another location.

aUnpacking the Refrigerator

bChoosing the Proper Location

cDisassembling/Assembling

dConnecting the Water Line

eLeveling and Door Alignment

WARNING

• Connect to potable water supply only.

en-us_main.book.book Page 9 Monday, July 3, 2023 9:26 AM

10 INSTALLATION

Unpacking the Refrigerator

WARNING

• Use two or more people to move and install the

refrigerator. Failure to do so can result in back

injury or other injury.

• The refrigerator is heavy. Protect the floor when

moving the refrigerator for cleaning or service.

Always pull the refrigerator straight out when

moving it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage could

occur.

• Keep flammable materials and vapors, such as

gasoline, away from the refrigerator. Failure to

do so can result in fire, explosion, or death.

NOTE

• Remove tape and any temporary labels from

your refrigerator before using. Do not remove

any warning labels, the model and serial number

label, or the Tech Sheet that is located under the

front of the refrigerator.

• To remove any remaining tape or glue, rub the

area briskly with your thumb. Tape or glue

residue can also be easily removed by rubbing a

small amount of liquid dish soap over the

adhesive with your fingers. Wipe with warm

water and dry.

• Do not use sharp instruments, rubbing alcohol,

flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the

surface of your refrigerator.

• Reinstall or adjust shelves as needed.

Refrigerator shelves are installed in the shipping

position. Reinstall shelves according to your

individual storage needs.

Choosing the Proper

Location

Water

The refrigerator must be located where a water

supply can be connected for the automatic

icemaker.

NOTE

• The water pressure must be 20 - 120 psi (138 -

827 kPa). If the refrigerator is installed in an area

with low water pressure (below 20 psi or 138

kPa), you can install a booster pump to

compensate for the low pressure.

Electricity

Use an individual, grounded outlet:115 Volts, 60

Hz, AC, 15 amps minimum.

WARNING

• Do not overload house wiring and cause a fire

hazard by plugging in multiple appliances in the

same outlet with the refrigerator.

• To reduce the risk of electric shock, do not install

the refrigerator in a wet or damp area.

Flooring

To avoid noise and vibration, the unit must be

installed and leveled on a solidly constructed floor.

If required, adjust the leveling legs to compensate

for the unevenness of the floor.

NOTE

• Installing on carpeting, soft tile surfaces, a

platform or weakly supported structure is not

recommended.

Ambient Temperature

Install this appliance in an area where the

temperature is between 55 °F (13 °C) and 110 °F

(43 °C).

If the temperature around the appliance is too low

or high, cooling ability may be adversely affected.

The internal temperatures could be affected by the

location of the appliance, the ambient

temperature, the frequency of door opening and

so on.

en-us_main.book.book Page 10 Monday, July 3, 2023 9:26 AM

11INSTALLATION

ENGLISH

Dimensions and Clearances

• Check the dimensions of the appliance and the installation path to ensure there is sufficient room to

move the refrigerator through doors or narrow openings.

• If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors. See Removing/

Assembling the Doors and Drawers in this manual.

• The installation location chosen for the refrigerator should allow space behind the unit for connections

and airflow and space in front to open the doors and drawers.

• Too small of a distance from adjacent items may result in lowered freezing capability and increased

electricity consumption charges. Allow at least 24 inches (610 mm) in front of the refrigerator to open the

doors, and at least 2 inches (50.8 mm) between the back of the refrigerator and the wall.

•3-Door

-Dimension/Clearance SRFB27S*

SRFB27W*

A Depth without Handle 29 1/8" (739 mm)

B Width 35 3/4" (908 mm)

C Height to Top of Case 68 7/8" (1750 mm)

D Height to Top of Hinge 70 1/4" (1785 mm)

E Back Clearance 2" (50 mm)

F Depth without Door 24 3/4" (628 mm)

G Depth with Handle 31 3/4“ (804 mm)

H Depth (Total with Freezer Drawer Open) 49” (1241 mm)

I Depth (Total with Door Open 90°) 43 5/8" (1106 mm)

B

A

CD

FI

H

E

G

en-us_main.book.book Page 11 Monday, July 3, 2023 9:26 AM

12 INSTALLATION

Removing/Assembling

Handles

These instructions are for models which ship with

the handles assembled. For models shipped with

the handles disassembled, follow the instructions

included in the handle package.

• Tools Needed

- Units shipped with disassembled handles:

3/32" and 1/4" Allen wrenches only

- Units shipped with assembled handles:

3/32", 1/8" and 1/4" Allen wrenches

When moving the refrigerator through a narrow

opening, removing the doors is preferred. If you

must remove the handles, be very careful not to

scratch the doors.

The appearance of the handles may vary from

what is shown.

CAUTION

• When assembling or disassembling the

refrigerator handles, grasp the handle firmly to

avoid dropping it.

• Do not swing the handle into nearby people or

animals.

• Make sure that the set screws are in place and

the handle footprints at the ends of the handles

are aligned correctly over the mounting

fasteners on the doors. The set screws should be

loose enough to allow the handle footprints to

slide down into place over the mounting

fasteners on the door.

• Make sure that there is not a gap between the

door and handle after assembling the handle.

Removing Refrigerator Handles

1 Loosen the set screws a with a 3/32 in. Allen

wrench and remove the handle.

2 If needed, loosen the mounting fasteners b

that connect the refrigerator door and handle

using a 1/4 in. Allen wrench, and remove the

mounting fasteners.

Assembling Refrigerator Handles

1 If needed, reassemble the mounting

fasteners a on the door with a 1/4 in. Allen

wrench.

2 Place the handle on the door by fitting the

handle footprints over the mounting

fasteners and tightening the set screws b

with a 3/32 in. Allen wrench.

Removing Freezer Drawer Handles

1 Loosen the set screws a located on the lower

side of the handle with a 3/32 in. Allen wrench

and remove the handle.

• For models shipped with the handles

assembled, use a 1/8 in. Allen wrench.

2 Loosen the mounting fasteners b with a 1/4

in. Allen wrench, and remove the mounting

fasteners.

Assembling Freezer Drawer

Handles

1 Assemble the mounting fasteners a at both

ends of the handle with a 1/4 in. Allen wrench.

en-us_main.book.book Page 12 Monday, July 3, 2023 9:26 AM

13INSTALLATION

ENGLISH

2 Place the handle on the door by fitting the

handle footprints over the mounting

fasteners and tightening the set screws b

with a 3/32 in. Allen wrench.

• For models shipped with the handles

assembled, use a 1/8 in. Allen wrench.

Removing/Assembling

Doors and Drawers

If the entrance door is too narrow for the

refrigerator to pass through, remove the

refrigerator doors and move the refrigerator

sideways through the doorway.

WARNING

• Use two or more people to remove and install

the refrigerator doors and drawers.

• Disconnect the electrical supply to the

refrigerator before installing.

• Do not put hands, feet or other objects into the

air vents or bottom of the refrigerator.

• Be careful when handling the hinge and hinge

lever.

• Remove food and bins before detaching the

doors and drawers.

• Do not hold the handle when removing or

replacing the doors and drawers as the handle

may come off.

• Tools Needed

- Phillips screwdriver

- Flat-head screwdriver

Removing the Hinge Cover

Remove the screws from the hinge cover at the top

of the refrigerator. Lift the hook (not visible),

located at the bottom of the front side of the cover

with a flat-head screwdriver.

Removing the Left Refrigerator

Door

1 The water supply is connected to the upper

right part of the rear surface of the

refrigerator. Remove the clip in the joint area.

Hold the water supply connection and gently

push the collet a to detach the water supply

line as shown.

NOTE

• Disassembling/Assembling the Water Lines

b Collet c Tube d Insert line e Clip

2 Pull out the water supply lines f. Disconnect

all the wire harnesses g . Unscrew the

ground wire h.

en-us_main.book.book Page 13 Monday, July 3, 2023 9:26 AM

14 INSTALLATION

3 Rotate the hinge lever i counterclockwise.

Lift the top hinge j free of the hinge lever

latch k.

CAUTION

• When lifting the hinge free of the latch, be

careful that the door does not fall forward.

4 Lift the door from the middle hinge pin and

remove the door.

CAUTION

• Place the door, inside facing up, on a

nonscratching surface.

Removing the Right Refrigerator

Door

1 Detach all the wire harnesses a. Unscrew the

ground wire b.

NOTE

• The number of wire harnesses may vary

depending on the model.

• Ground wire is only present on some models.

2 Rotate the hinge lever c clockwise. Lift the

top hinge d free of the hinge lever latch e.

CAUTION

• When lifting the hinge free of the latch, be

careful that the door does not fall forward.

3 Lift the door from the middle hinge pin and

remove the door.

CAUTION

• Place the door, inside facing up, on a

nonscratching surface.

Removing Freezer Drawers

WARNING

• Use two or more people to remove and install

the refrigerator doors and freezer drawer.

en-us_main.book.book Page 14 Monday, July 3, 2023 9:26 AM

15INSTALLATION

ENGLISH

• Be careful of sharp hinges on both sides of the

drawer.

• When you lay the drawer down, be careful not to

damage the floor.

• Do not sit or stand on the freezer drawer.

• To prevent accidents, keep children and pets

away from the drawer. Do not leave the drawer

open. If the Durabase® storage bin is removed

from the freezer drawer, there is sufficient space

for a small child or pet to crawl inside.

1 Pull the drawer open to full extension.

2 Gently lift and pull out the ice bin(s).

NOTE

• The number of ice bins may vary depending on

the model.

3 Lift the front of the drawer up, then pull it

straight out.

4 Remove the Durabase basket from the rails.

Remove the screws from the rails at both

ends.

5 Grip both sides of the drawer and pull it up to

remove it from the rails.

CAUTION

• Do not hold the handle when removing or

replacing the drawer. The handle may come off,

causing personal injury.

6 Hold both rails and push them in

simultaneously.

Removing the Full Convert Drawer

This feature is only available on some models.

1 Pull the drawer open to full extension.

Remove the basket from the rails.

en-us_main.book.book Page 15 Monday, July 3, 2023 9:26 AM

16 INSTALLATION

2 Hold both sides of the door and remove it

from the rails.

Assembling the Full Convert

Drawer

This feature is only available on some models.

1 Grasp the door on each side and lower it into

place on the rails.

2 Pull the drawer open to full extension. Lower

the basket onto the rails.

Assembling Freezer Drawers

1 Pull out both rails simultaneously, until they

are fully extended.

2 Grasp the drawer on each side and hook the

drawer supports into the rail tabs located on

both sides.

CAUTION

• Do not hold the handle when removing or

replacing the drawer. The handle may come off,

causing personal injury.

3 Lower the door into its final position and

insert the screws in the rails on both sides.

en-us_main.book.book Page 16 Monday, July 3, 2023 9:26 AM

17INSTALLATION

ENGLISH

4 Insert the drawer into the frame, and push

the drawer back until it clicks into place.

5 Replace the ice bin(s) in the drawer. Insert the

Durabase basket in the rail assembly.

NOTE

• The number of ice bins may vary depending on

the model.

Assembling the Right Refrigerator

Door

CAUTION

• Install the right-side door first.

1 Make sure that the plastic sleeve is inserted in

the bottom of the door. Lower the door onto

the middle hinge pin as shown in the figure.

2 Fit the hinge a over the hinge lever latch b

and slot it into place. Rotate the lever c

counterclockwise to secure the hinge.

3 Connect all the wire harnesses d. Screw in

the ground wire e.

NOTE

• The number of wire harnesses may vary

depending on the model.

• Ground wire is only present on some models.

Assembling the Left Refrigerator

Door

CAUTION

• Install the left refrigerator door after the right

door is installed.

1 Make sure that the plastic sleeve is inserted in

the bottom of the door. Install the refrigerator

door onto the middle hinge.

en-us_main.book.book Page 17 Monday, July 3, 2023 9:26 AM

18 INSTALLATION

2 Fit the hinge a over the hinge lever latch b

and slot it into place. Rotate the lever c

clockwise and fasten the hinge.

3 Connect all the wire harnesses and the

ground wire.

4 Push the water supply lines into the hole on

the top case and pull them through the

backplate.

5 Hold the water supply connection and gently

push in the collet d to connect the water

supply lines as shown. Insert the tube at least

5/8 inch (15 mm) into the connector. Insert

the clip on the joint to fasten the tubes in

place.

NOTE

• Disassembling/Assembling the Water Lines

e Collet f Tube g Insert line h Clip

• Gently press the collet and insert the tube until

only one line shows on the tube.

Assembling the Hinge Cover

Position the hinge cover in its place. Insert and

tighten the cover screws.

Connecting Refrigerator to

Water Supply

Before Beginning

These instructions assume you have an existing

water supply connection for the refrigerator. If

necessary, call a qualified plumber to install a

water supply line for the refrigerator.

• Turn the icemaker OFF if the refrigerator will be

used before the water line is connected.

• Do not install the icemaker tubing in areas

where the ambient temperatures fall below

freezing.

WARNING

• Connect to potable water supply only.

CAUTION

• To prevent burns and product damage, only

connect the refrigerator water line to a cold

water supply.

en-us_main.book.book Page 18 Monday, July 3, 2023 9:26 AM

19INSTALLATION

ENGLISH

• Wear eye protection during installation to

prevent injury.

Water Pressure

You will need a cold water supply.

Water Pressure

•Models with water filter:

- 20 - 120 psi (138 - 827 kPa)

•Where reverse osmosis water filtration

system is connected to a cold water supply:

- 40 - 60 psi minimum to reverse osmosis

system (2.8 kgf/cm2 - 4.2 kgf/cm2, or less than

2 - 3 seconds to fill a cup of 7 oz capacity)

If the water pressure from the reverse osmosis

system is less than 20 psi or 138 kPa or 1.4 kgf/cm2

(takes more than 4 seconds to fill a cup of 7 oz or

198 cc capacity):

• Check to see if the sediment filter in the reverse

osmosis system is blocked. Replace the filter if

necessary.

• Allow the storage tank on the reverse osmosis

system to refill after heavy usage.

• If the water pressure remains low, call a

licensed, qualified plumber.

• All installations must be in accordance with local

plumbing code requirements.

Supplies Needed

•Copper or PEX Tubing, ¼ in. outer diameter, to

connect the refrigerator to the water supply. Be

sure both ends of the tubing are cut square. To

determine how much tubing you need, measure

the distance from the water valve on the back of

the refrigerator to the water supply pipe. Then,

add 8 feet (2.4 m). Be sure there is sufficient

extra tubing (about 8 feet [2.4 m] coiled into 3

turns of about 10 in. [25 cm] diameter) to allow

the refrigerator to move out from the wall after

installation.

•½ in. or adjustable wrench.

•Flat-blade and Phillips screwdrivers.

•Two ¼ in. outer diameter compression nuts

and 2 ferrules (sleeves) to connect the copper

tubing to the shutoff valve and the refrigerator

water valve. If you are using a PEX water line kit,

it may already have the required fittings at either

end.

• If your existing copper water line has a flared

fitting at the end, purchase an adapter (available

at plumbing supply stores) to connect the water

line to the refrigerator OR cut off the flared

fitting with a tube cutter and use a compression

fitting.

NOTE

• The hookup line cannot be white, plastic tubing.

Licensed plumbers must use only copper tubing

(NDA tubing #49595 or #49599) or Cross Link

Polyethylene (PEX) tubing.

• Be sure there is sufficient extra tubing (about 8

ft. coiled into three turns of about 10 in.

diameter) to allow the refrigerator to move out

from the wall after installation.

Connecting Water Line to

Refrigerator

1 Connect the tubing to the shutoff valve.

• Place the compression nut and ferrule

(sleeve) onto the end of the copper tubing

and connect it to the shutoff valve. If you

are using PEX, the tubing may already have

the required fittings at either end. Make

sure the tubing is fully inserted into the

valve. Tighten the compression nut

securely.

aPacking Nut

bShutoff Valve

cCompression Nut

dFerrule (sleeve)

en-us_main.book.book Page 19 Monday, July 3, 2023 9:26 AM

20 INSTALLATION

2 Flush out the tubing into a bucket.

• Flush out the tubing coming from the home

water supply until the water is clear. Shut

the water off at the water valve after about

one quart of water has been flushed

through the tubing.

NOTE

• Before making the connection to the

refrigerator, be sure that the refrigerator power

cord is not plugged into the wall outlet.

3 Remove the flexible plastic cap from the water

valve on the refrigerator.

4 Place the compression nut and ferrule (sleeve)

onto the end of the tubing as shown. If you

are using a PEX connection kit, it may already

have the required fittings.

5 Insert the end of the copper or PEX tubing

into the connection as far as possible. While

holding the tubing, tighten the fitting.

aTubing Clamp

b¼ in. Tubing

c¼ in. Compression Nut

dFerrule (sleeve)

eRefrigerator Connection

6 Turn the water on at the shutoff valve.

• Tighten any connections that leak.

CAUTION

• Check to see if leaks occur at the water line

connections.

• Make sure the house water valve is fully open. If

it is not open completely, the icemaker and

dispenser may not work properly.

Leveling and Door

Alignment

Leveling

The refrigerator has two front leveling legs. Adjust

the legs to alter the tilt from front-to-back or side-

to side. If the refrigerator seems unsteady, or the

doors do not close easily, adjust the refrigerator’s

tilt using the instructions below:

1 Turn the leveling leg to the left to raise that

side of the refrigerator or to the right to lower

it. It may take several turns of the leveling leg

to adjust the tilt of the refrigerator.

NOTE

• A flare nut wrench works best, but an open-end

wrench will suffice. Do not over-tighten.

2 Open both doors and check to make sure that

they close easily. If the doors do not close

easily, tilt the refrigerator slightly more to the

rear by turning both leveling legs to the left. It

may take several more turns, and be sure to

turn both leveling legs the same amount.

en-us_main.book.book Page 20 Monday, July 3, 2023 9:26 AM

La page charge ...

Yes SRFB27W3 Manuel utilisateur

Yes SRFB27W3 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents