Ring 5C28S6 TPUB Alarm Bear Glass Break Sensor Manuel utilisateur

Taper
Manuel utilisateur
Important Product Information
Renseignements Importants
Relatifs au Produit
ENGLISH
IMPORTANT PRODUCT INFORMATION
SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER
INJURY OR DAMAGE.
WARNING: Your device should only be used in accordance with the specific instructions for use and intended purpose
of the device. Using your device in any way other than its intended purpose could cause injury to yourself, others and/
or damage to the device or property.
WATCH FOR SMALL PARTS! Your device and accessories may present a choking hazard to small children. Keep them
out of reach of small children.
CAUTION: The device is not waterproof and as such should not be submerged in water, doing so could cause injury
to yourself, others and/or damage to the device.
CAUTION: To reduce the risk of falling, take extra caution when using a ladder or similar equipment to mount the product.
BATTERY SAFETY
This product contains alkaline batteries. This device requires batteries for use. Only use new 1.5V alkaline AA-sized
batteries. Never mix old and new batteries. Keep all of the batteries out of the reach of children. Do not open, disas-
semble, puncture, cut, bend, shred or heat the batteries and do not allow metal objects to touch the battery terminals
on the device as they can become hot and cause burns. Remove all batteries if they are worn out or before storing your
Device for an extended period of time. Dispose of all batteries in accordance with applicable laws and regulations
and do not dispose of batteries by throwing them into a fire. If any batteries begin to leak, take steps to prevent the
fluid from coming into direct contact with skin or clothes as the fluid could be corrosive and may be toxic. Remove
the batteries and clean the battery compartment in accordance with the battery manufacturer’s recommendations.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recom -
mended by the manufacturer. Dispose of the used batteries according to the manufacturer’s instructions.
Maintaining Your Ring Glass Break Sensor
The Ring Glass Break Sensor is for indoor use only. Use only accessories supplied with your device, or specifically
marketed for use with your device, to power your device.
PRODUCT SPECIFICATIONS
Device Name: Ring Glass Break Sensor
Model Number: 5C28S6
Electrical Rating: 3 AA Alkaline Batteries (1.5V)
Temperature Rating: 32°F to 120°F (0°C to 49°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your
device in accordance with your local laws and regulations. For information about recycling your device, go to
amazon.com/devicesupport.
Terms of Service and Warranty
By purchasing or using the product, you agree to the Terms of Service found at ring.com/terms. For information on
our warranty visit ring.com/legal.
FOR CONSUMERS IN THE USA
Supplier’s Declaration of Conformity — Compliance Information Statement
Unique Identifier: Ring Glass Break Sensor
Model Number: 5C28S6
FCC ID: 2AB2Q5C28S6
Responsible Party and Party issuing Supplier’s Declaration of Conformity
Ring LLC, 1523 26th St., Santa Monica, CA 90404
www.ring.com / [email protected]
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly
approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC
and can be found by inputting such Product’s FCC ID (which can be found on the device) into the FCC ID Search form
available at fcc.gov/oet/ea/fccid.
EMBOSS
LEVEL 2
DEBOSS
GLOSS
VARNISH
SATIN
VARNISH
MATTE
VARNISH
SPOT UV
PANTONE
Cool Gray 11 C
PANTONE
0000C/U
PANTONE
0000C/U
PANTONE
0000C/U
PANTONE
0000C/U
PANTONE
0000C/U
K
COLOR GUIDE
VARNISH / LAMINATION EMBOSS /DEBOSS CUTTER
SUBSTRATE:PROJECT #: RING21008A CUSTOMER: Ring NA EXT SIZE: 000 x 000 x 000mm
PROCESS: Printing INT SIZE: 000 x 000 x 000mm
BRAND:
STYLE: NA
CUTTER / CAD #:
DESIGNER:
NARing PN:22-003307-01
GPA PN: 020203202103995
ARTWOR K #: V01 NA
BARCODE #: NA Anna ISSUE: 4
IMPORTANT NOTES: Ple ase check this artwo rk proof th oroughly, in cluding al l copy, colou rs, cutter guides an d legal/ma ndatory in formation,
prior to approval. If you have any questions relating to this or if you require any guidance on checking artwork proofs, please let us know and
we will happily advise. Please notify us immediately if you have any concerns regarding this file.
NOTES: *
EMBOSS
LEVEL 1
DATE: 16-07-2021
Information Regarding Exposure to Radio Frequency Energy
The output power of the radio technology used in the Products is below the radio frequency exposure limits set by the
FCC. Nevertheless, it is advised to use this product in such a manner that minimizes the potential for human contact
during normal operation. This device should be installed and operated with at least 20 cm between the radiator
and your body.
FOR CONSUMERS IN CANADA
Innovation, Science and Economic Development Canada (ISED) Compliance
IC ID: 10256A-5C28S6
This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
FRANÇAIS
RENSEIGNEMENTS IMPORTANTS RELATIFS AU PRODUIT
RENSEIGNEMENTS RELATIFS À LA SÉCURITÉ
LE NON-RESPECT DE CES CONSIGNES DE SÉCURITÉ POURRAIT CAUSER UN INCENDIE, UNE DÉCHARGE
ÉLECTRIQUE, OU D’AUTRES BLESSURES OU DOMMAGES.
AVERTISSEMENT : Votre appareil ne doit être utilisé que conformément à son usage prévu et aux instructions précises
relatives à son usage. L’utilisation de votre appareil d’une manière autre que celle prévue pourrait vous blesser, blesser
d’autres personnes ou endommager l’appareil ou votre propriété.
FAITES ATTENTION AUX PETITES PIÈCES! L’appareil et les accessoires peuvent présenter un risque d’étouement pour
les enfants en bas âge. Gardez-les hors de la portée des enfants en bas âge.
ATTENTION : Votre appareil n’est pas étanche et ne doit donc pas être immergé dans l’eau, car cela pourrait vous
blesser, blesser d’autres personnes ou endommager l’appareil.
ATTENTION : Afin de réduire les risques de chute, soyez particulièrement prudent lorsque vous utilisez une échelle ou
tout équipement similaire pour l’installation du produit.
SÉCURITÉ CONCERNANT LES PILES
Ce produit contient des piles alcalines. Cet appareil nécessite des piles pour fonctionner. N’utilisez que des piles
alcalines AA neuves de 1,5 V. Ne mélangez jamais des piles usées et des piles neuves. Gardez toutes les piles hors
de la portée des enfants. Ne pas ouvrir, démonter, percer, couper, plier, déchiqueter ou chauer les piles et ne pas
laisser d’objets métalliques toucher les bornes de la pile sur l’appareil, car elles peuvent devenir chaudes et causer
des brûlures. Retirez toutes les piles si elles sont usées ou avant de ranger votre appareil pendant une période
prolongée. Éliminez toutes les piles conformément aux lois et règlements en vigueur et ne les jetez pas au feu. Si les
piles commencent à fuir, prenez les mesures nécessaires pour empêcher le liquide d’entrer en contact direct avec la
peau ou les vêtements, car il pourrait être corrosif et toxique. Retirez les piles et nettoyez le compartiment des piles
conformément aux recommandations du fabricant.
AVERTISSEMENT : Risque d’explosion si les piles sont remplacées incorrectement. Remplacez-les uniquement par un
modèle identique ou équivalent recommandé par le fabricant. Jetez les piles usées conformément aux instructions
du fabricant.
Entretien du de Ring Glass Break Sensor
Ring Glass Break Sensor est destiné à usage intérieur seulement. Utilisez uniquement les accessoires fournis avec votre
appareil, ou spécifiquement commercialisés pour une utilisation avec votre appareil, pour alimenter votre appareil.
CARACTÉRISTIQUES DU PRODUIT
Nom de l’appareil : Ring Glass Break Sensor
Numéro de modèle : 5C28S6
Caractéristiques électriques : 3 piles alcalines AA (1,5 V)
Températures de fonctionnement : de 0 °C à 49 °C (32 °F à 120 °F)
RECYCLEZ VOTRE APPAREIL CORRECTEMENT
Dans certaines régions, l’élimination de certains appareils électroniques est réglementée. Assurez-vous de jeter ou de
recycler votre appareil conformément aux lois et règlements locaux. Pour obtenir des renseignements sur le recyclage
de votre appareil, visitez la page amazon.com/devicesupport.
Conditions de service et de garantie
L’utilisation du produit est soumise à votre inscription auprès de Ring et à votre acceptation des conditions d’utilisation
disponibles sur ring.com/terms. Pour obtenir des renseignements sur la garantie, visitez la page ring.com/warranty
POUR LES CONSOMMATEURS AU CANADA
Conformité aux exigences d’Innovation, Sciences et Développement économique Canada (ISDE)
Numéro IC : 10256A-5C28S6
Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux normes CNR d’Innova-
tion, Sciences et Développement économique Canada. Son utilisation est soumise aux deux conditions ci-dessous.
1. Cet appareil ne doit pas causer d’interférences.
2.
Cet appareil doit accepter toute interférence, y compris les interférences pouvant causer un fonctionnement indé-
sirable de l’appareil.
Renseignements concernant l’exposition à l’énergie des fréquences radio
Cet équipement est conforme aux limites d’exposition aux fréquences radio stipulées dans le document IC CNR-102
RF pour les environnements non contrôlés. Cet équipement doit être installé et utilisé à une distance minimale de 20
centimètres entre le radiateur et votre corps.
Ring LLC 1523 26th St. Santa Monica, CA 90404
© 2021 Ring LLC or its aliates. Ring and all related
marks are trademarks of Ring LLC or its aliates.
22-003307-01
  • Page 1 1
  • Page 2 2

Ring 5C28S6 TPUB Alarm Bear Glass Break Sensor Manuel utilisateur

Taper
Manuel utilisateur