Honeywell PRO TH2000 Series Programmable Thermostats Manuel utilisateur

Série PRO TH2000 Series

Programmable Thermostats

Thermostats programmables

Termostatos programables

Operating Manual

Mode d’emploi

Manual de Uso

firealarmresources.com

ENGLISH

PRO TH2000 Series

This manual covers the following models:

TH2110D: For 1-Heat / 1-Cool systems

TH2210D

: For 2-Heat / 1-Cool heat pump systems

(Remove thermostat from wallplate and turn over to find model number.)

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502.

Read and save these instructions.

® U.S. Registered Trademark. Patents pending.

CAUTION: EQUIPMENT DAMAGE HAZARD.

To prevent possible compressor damage, do not use Cooling mode when the

outdoor temperature is below 50 °F (10 °C).

firealarmresources.com

Operating Manual

ENGLISH

Overview

Thermostat features ............................. 1

Quick start ............................................ 2

Quick reference to controls .................. 3

Quick reference to display.................... 4

Programming & Operation

Setting the clock ................................... 5

System switch (Heat/Cool) ................... 6

Fan switch (Auto/On)............................ 7

Using the schedule.......................... 8-10

Temporary schedule override ..............11

Permanent schedule override ............ 12

Adaptive Intelligent Recovery™ ......... 13

Compressor protection ....................... 13

Appendices

Battery replacement ........................... 14

In case of difficulty.............................. 15

Customer assistance.......................... 16

2-year limited warranty ....................... 17

Table of contents

Your new thermostat is pre-programmed

and ready to go!

See page 2 for quick start.

firealarmresources.com

PRO TH2000 Series

1

ENGLISH

Your new Honeywell thermostat has been designed to give you many years of reliable

service and easy-to-use, push-button climate control.

Features

• Backlit display is easy to read

• Displays ambient (measured) temperature at all times

• One-touch access to setpoint temperature

• Energy Star® compliant to greatly reduce your heating/cooling expenses

• Separate programmable weekday/weekend schedules (5+2 day programming)

• Temporary and permanent override of schedule

• Adaptive Intelligent Recovery™ ensures right temperature at the right time

• Built-in compressor protection

About your new thermostat

firealarmresources.com

Operating Manual

2

ENGLISH

Simply perform the three steps below and the thermostat is in operation:

nSet the clock.................................................................................................. See page 5

oSelect whether to heat or cool....................................................................... See page 6

pSelect whether to run the fan continuously or only when needed ................. See page 7

Your thermostat is pre-programmed with Energy Star® settings. If you do not wish to use

these settings, you can:

Modify the schedule .................................................................................... See page 10

Temporarily override the schedule .............................................................. See page 11

Permanently override the schedule............................................................. See page 12

This thermostat is ready to go

firealarmresources.com

PRO TH2000 Series

3

ENGLISH

Quick reference to controls

System switch (see page 6)

•Cool: System is in Cooling mode.

•Off: System is off.

•Heat: System is in Heating mode.

•Em Heat: System is in Emergency Heat mode.

Fan Switch (see page 7)

•On: Fan runs continuously.

•Auto: Fan runs only when

heating or cooling is taking place.

Press to adjust temperature

Screen

Lit for 12 seconds when you press any button.

Press to set clock,

day or schedule

(see pages 5 & 10).

Press to override

schedule and

hold temperature

(see page 12).

Press to run

(follow) schedule

(see page 8).

firealarmresources.com

Operating Manual

4

ENGLISH

Quick reference to display screen

* When Heat On or Cool On is flashing, compressor protection is engaged (see page 13).

** Applies to TH2210D model only.

Temperature

The ambient (measured) temperature

is normally displayed. To view the

setpoint temperature, press either of

the temperature adjustment buttons

once. The setpoint temperature will

appear for five seconds.

System status

• Cool On: Cooling is activated. *

• Heat On: Heating is activated. *

• Aux On: Auxiliary heat is activated. **

Low-battery warning

(see page 14)

Setpoint indicator

Appears when the setpoint

temperature is displayed.

Clock

Schedule period

Permanent schedule override

(see page 12)

Temporary schedule override

(see page 11)

firealarmresources.com

PRO TH2000 Series

5

ENGLISH

nPress the Set button. Set Time will flash on the screen.

oPress the  or  button to set the time.

pPress the Set button again. Set Day will flash on the screen.

qPress the  or  button to select the day of the week.

rPress the Run button to save the changes & exit. (The changes are also

saved if you do not press any button for 60 seconds.)

NOTE: The clock has lost its settings when the time display flashes. If the

thermostat is following the schedule, it will use the temperature settings

programmed for the Wake period of the weekdays until you re-adjust the

clock.

Set the clock

Set Time

Set Day

firealarmresources.com

Operating Manual

6

ENGLISH

System switch

Use the SYSTEM switch to place the system in one of the

following modes:

•Cool: System is in Cooling mode.

•Off: System is off.

•Heat: System is in Heating mode.

•Em Heat: System is in Emergency Heat mode. Only auxiliary

heating can be activated. The compressor is disabled. (This

mode is available on TH2210D model only.)

CAUTION: EQUIPMENT DAMAGE HAZARD.

Do not use Cooling mode when the outdoor

temperature is below 50 °F (10 °C).

firealarmresources.com

PRO TH2000 Series

7

ENGLISH

Fan switch

Use the FAN switch to select the fan operation.

•Auto: The fan runs only when heating or

cooling is activated (commonly used setting).

•On: The fan runs continuously. Use this

setting for improved air circulation or for

more efficient air cleaning.

firealarmresources.com

Operating Manual

8

ENGLISH

Press the Run button to follow the programmed schedule. For maximum energy savings

while maintaining comfort, you can program the schedule such that the temperature is at an

economical level when you sleep or leave for work and at a comfortable level when you are

awake and at home. You can program up to four periods per day:

To program a period, you need to set its start time and its two temperature settings (one

when the thermostat is in cooling mode and another one when it is in heating mode). The

same settings are used every day from Monday to Friday and another set of settings are

used for Saturday and Sunday. For example, you could program all four periods for the

weekdays but only two periods (Wake and Sleep) for the weekends.

Using the schedule

Wake Starts when you wake up

Leave Starts when you leave for work

Return Starts when you return home

Sleep Starts when you go to sleep

firealarmresources.com

PRO TH2000 Series

9

ENGLISH

The thermostat has been programmed with Energy Star® settings. These settings can

reduce your energy bills by 33%. See the next page if you wish to modify the settings.

Energy Star settings

Period Weekdays Weekends

Start time Heat Cool Start time Heat Cool

Wake 6:00 am 70 °F (21 °C) 75 °F (24 °C) 6:00 am 70 °F (21 °C) 75 °F (24 °C)

Leave 8:00 am 62 °F (17 °C) 83 °F (28 °C) - - - - - -

Return 6:00 pm 70 °F (21 °C) 75 °F (24 °C) - - - - - -

Wake 10:00 pm 62 °F (17 °C) 78 °F (26 °C) 10:00 pm 62 °F (17 °C) 78 °F (26 °C)

firealarmresources.com

Operating Manual

10

ENGLISH

n

Press the

Set

button 3 times until

Set Schedule

appears. The start time of

the first period (Wake) of the week days (Mon-Fri) will flash.

oPress the  or  button to set the time.

pPress the Set button. The temperature setting for that period will flash.

qTo program the temperature settings for the cooling mode, place the

System switch in Cool. To program the temperature settings for the

heating mode, place the switch in Heat.

rPress the  or  button to set the temperature.

sPress the Set button. The start time of the next period will flash.

tRepeat steps 2 through 6 for each of the remaining periods.

uOnce all adjustments are made, press the Run button to save them and

exit. (The changes are also saved if you do not press any button for 60 seconds.)

Modifying the schedule

The Wake

period for the

weekdays is

set to 6 a.m.

and 70 °F

(Heating

mode).

To skip a

period (except

Wake), press

the Hold

button for 4

sec. while that

period is

displayed.

firealarmresources.com

PRO TH2000 Series

11

ENGLISH

To temporarily ignore the schedule, press  or  until the desired

temperature is displayed. The word Temporary will appear on the

screen. The new temperature will be used until the next period

begins.

NOTE: Pressing  or  once will display the setpoint temperature.

To change the setpoint temperature, press either button more than

once.

Press the Run button if you wish to cancel the temporary setting

before the beginning of the next period.

Temporary override of schedule

firealarmresources.com

Operating Manual

12

ENGLISH

To permanently ignore the schedule, press  or  until the desired

temperature is displayed. Then, press the Hold button to maintain

the new temperature indefinitely. The word Hold will appear on the

screen.

Press the Run button if you wish to cancel the override and resume

the schedule. The word Hold will disappear and the thermostat will

be set to the temperature programmed for the current period.

Permanent override of schedule

firealarmresources.com

PRO TH2000 Series

13

ENGLISH

Adaptive Intelligent Recovery™ allows the thermostat to “learn” how long your furnace or air

conditioner takes to reach the set temperature. Simply program the desired times and desired

temperatures into the schedule. The thermostat will determine when to activate heating or cooling

so that the desired temperature is attained at the desired time.

Example: If you set the Wake time to 6 a.m. and the temperature to 70 °F (21 °C), the heat will

come on before the set time, so the temperature is 70 °F (21 °C) by the time you wake at 6 a.m.

Your thermostat has a feature that helps prevent damage to the compressor of your air

conditioning or heat pump system. Damage can occur if the compressor is restarted too soon after

shutdown. This feature forces the compressor to wait 5 minutes before restarting. During the wait

time, the message Cool On or Heat On flashes on the screen. When the safe wait time has

elapsed, the message stops flashing and the compressor turns on.

Adaptive Intelligent Recovery (AIR)

Built-in compressor protection

firealarmresources.com

Operating Manual

14

ENGLISH

NOTE: Batteries are optional (serving as backup power) only if your

thermostat is connected to 24 VAC.

Install two fresh AAA batteries when the low-battery icon

flashes on the screen. The icon appears for 60 days before the

batteries are depleted.

Replace batteries once a year, or when you will be away for

more than a month.

Most settings are stored in non-volatile (permanent) memory.

Only the clock and the day must be set if the thermostat was

without AC power or batteries.

NOTE: The low-battery icon will not appear when the batteries are

depleted if the thermostat is connected to 24 VAC.

Battery replacement

Set the System switch to Off before removing the

batteries. Otherwise, the heating/cooling system could

remain activated even when batteries are removed.

firealarmresources.com

PRO TH2000 Series

15

ENGLISH

In case of difficulty

Screen is blank. • Check circuit breaker and reset if necessary.

• Ensure the heating/cooling system is powered up.

• Ensure the furnace door is properly closed.

• Ensure two fresh AAA alkaline batteries are correctly installed.

Temperature settings cannot be

changed.

• You are setting the temperature outside its allowable range:

• Heat: 40 °F to 90 °F (4.5 °C to 32 °C).

• Cool: 50 °F to 99 °F (10 °C to 37 °C).

Cool On or Heat On is flashing. • The compressor protection delay is underway. Wait for the delay

to end (maximum of 5 minutes).

HI appears on the screen. • The ambient (measured) temperature is above 122 °F (50 °C).

LO appears on the screen. • The ambient (measured) temperature is below 32 °F (0 °C).

E1 appears on the screen. • The temperature sensor circuit is opened. Replace the thermostat.

E2 appears on the screen. • The temperature sensor circuit is shorted. Replace the thermostat.

firealarmresources.com

Operating Manual

16

ENGLISH

Customer assistance

For assistance with this product, please visit

http://yourhome.honeywell.com.

Or call Honeywell Customer Care toll-free at

1-800-468-1502.

To save time, please note your model number and

date code before calling.

firealarmresources.com

La page charge ...

Honeywell PRO TH2000 Series Programmable Thermostats Manuel utilisateur

Honeywell PRO TH2000 Series Programmable Thermostats Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents