Wen VC9209 Manuel utilisateur

Marque: Wen

Modèle: VC9209

Catégorie: Aspirateurs

Taper: Manuel utilisateur

9.25-GALLON

WET/DRY VACUUM

Instruction Manual

MODEL VC9209

IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability,

ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged,

trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use

your tool properly and for its intended purpose, you will enjoy years of safe, reliable service.

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

TECHSUPPOR[email protected]1-847-429-9263 (M-F 8AM-5PM CST)

For replacement parts and the most up-to-date instruction manuals, visit WENPRODUCTS.COM

CONTENTS

WELCOME 3

Introduction ..................................................................................................... 3

Speciﬁcations ................................................................................................... 3

SAFETY 4

General Safety Rules ........................................................................................ 4

Wet / Dry Vacuum Safety Warnings ................................................................. 6

Electrical Safety Warnings................................................................................ 7

BEFORE OPERATING 8

Unpacking & Packing List .................................................................................8

Know Your Wet / Dry Vacuum .......................................................................... 9

Assembly & Adjustments ................................................................................10

OPERATION & MAINTENANCE 11

Operation ....................................................................................................... 11

Maintenance ....................................................................................................12

Troubleshooting Guide ....................................................................................13

Exploded View & Parts List .............................................................................14

Warranty Statement ....................................................................................... 16

To purchase replacement parts or accessories for your tool, visit WENPRODUCTS.COM

French Instructions (Mode d’Emploi en Français) ......................................... 17

HEPA F9 Replacement Filter (Part No. VC4710-038)

SPECIFICATIONS

Model Number VC9209

Motor 1200W, 120V, 60 Hz, 10A

Dust Capacity 9.25 Gallons (35 L)

Filter Rating HEPA F9 (Part No. VC4710-038)

Product Dimensions 17.6 in. x 18.3 in. x 21.9 in.

Product Weight 24.25 Pounds

INTRODUCTION

Thanks for purchasing the WEN Wet / Dry Vacuum. We know you are excited to put your tool to work, but ﬁrst,

please take a moment to read through the manual. Safe operation of this tool requires that you read and understand

this operator’s manual and all the labels afﬁxed to the tool. This manual provides information regarding potential

safety concerns, as well as helpful assembly and operating instructions for your tool.

NOTE: The following safety information is not meant to cover all possible conditions and situations that may occur.

WEN reserves the right to change this product and speciﬁcations at any time without prior notice.

At WEN, we are continuously improving our products. If you ﬁnd that your tool does not exactly match this manual,

please visit wenproducts.com for the most up-to-date manual or contact our customer service at 1-847-429-9263.

Keep this manual available to all users during the entire life of the tool and review it frequently to maximize

safety for both yourself and others.

SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. The safety symbols and the explanations

with them deserve your careful attention and understanding. Always follow the safety precautions to reduce the

risk of ﬁre, electric shock or personal injury. However, please note that these instructions and warnings are not

substitutes for proper accident prevention measures.

GENERAL SAFETY RULES

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂammable liquids,

gases or dust. Power tools create sparks which may ig-

nite the dust or fumes.

3. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never mod-

ify the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded surfac-

es such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

3. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of elec-

tric shock.

4. Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric

shock.

5. When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric

shock.

6. If operating a power tool in a damp location is un-

avoidable, use a ground fault circuit interrupter (GFCI)

protected supply. Use of a GFCI reduces the risk of elec-

tric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use a

power tool while you are tired or under the inﬂuence

of drugs, alcohol or medication. A moment of inatten-

tion while operating power tools may result in serious

personal injury.

2. Use personal protective equipment. Always wear

eye protection. Protective equipment such as a respira-

tory mask, non-skid safety shoes and hearing protection

used for appropriate conditions will reduce the risk of

personal injury.

3. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your ﬁnger on the switch or

energizing power tools that have the switch on invites

accidents.

4. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

5. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jew-

elry. Keep your hair and clothing away from moving

parts. Loose clothes, jewelry or long hair can be caught

in moving parts.

Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”

in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

result in electric shock, ﬁre and/or serious injury.

GENERAL SAFETY RULES

7. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

2. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained us-

ers.

5. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s opera-

tion. If damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

power tools.

6. Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking into ac-

count the working conditions and the work to be per-

formed. Use of the power tool for operations different

from those intended could result in a hazardous situa-

tion.

8. Use clamps to secure your workpiece to a stable

surface. Holding a workpiece by hand or using your

body to support it may lead to loss of control.

9. KEEP GUARDS IN PLACE and in working order.

SERVICE

1. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is main-

tained.

CALIFORNIA PROPOSITION 65 WARNING

Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities may contain

chemicals, including lead, known to the State of Califor-

nia to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling. Some examples of

these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other

masonry products.

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies depending on

how often you do this type of work. To reduce your ex-

posure to these chemicals, work in a well-ventilated area

with approved safety equipment such as dust masks

specially designed to ﬁlter out microscopic particles.

Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”

in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

result in electric shock, ﬁre and/or serious injury.

WET/DRY UTILITY VACUUM SAFETY

1. Never operate this unit with ﬂammable materials or

vapors are present. This unit can produce sparks or arcs

due to static electricity that can cause ﬁre or explosions.

2. Do not use this vacuum to collect lead paint debris.

Doing so may disperse ﬁne lead particles into the en-

vironment. This vacuum is not intended for use under

EPA Regulation 40 CFR Part 745 for lead paint material

cleanup.

3. Do not use this vacuum to collect carcinogenic, com-

bustible, toxic, or other hazardous materials.

4. Do not collect anything that is burning or smoking

with this vacuum. This includes but is not limited to cig-

arettes, matches, or hot ashes.

5. Always use vacuum with ﬁlter in place.

6. Always wear safety glasses when operating the vacu-

um to avoid particles being blown into eyes.

WET / DRY VACUUM SAFETY WARNINGS

WARNING! Do not operate the power tool until you have read and understood the following instructions and

the warning labels.

ELECTRICAL INFORMATION

AMPERAGE REQUIRED GAUGE FOR EXTENSION CORDS

25 ft. 50 ft. 100 ft. 150 ft.

10A 18 gauge 16 gauge 14 gauge 12 gauge

3. Check with a licensed electrician or service personnel if you do not completely under-

stand the grounding instructions or whether the tool is properly grounded.

4. Use only three-wire extension cords that have three-pronged plugs and outlets that

accept the tool’s plug. Repair or replace a damaged or worn cord immediately.

CAUTION! In all cases, make certain the outlet in question is properly grounded. If you

are not sure, have a licensed electrician check the outlet.

GUIDELINES AND RECOMMENDATIONS FOR EXTENSION CORDS

When using an extension cord, be sure to use one heavy enough to carry the current your

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding provides the path of least resistance for an electric current

and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding

conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and

grounded in accordance with ALL local codes and ordinances.

1. Do not modify the plug provided. If it will not ﬁt the outlet, have the proper outlet installed by a licensed electri-

cian.

2. Improper connection of the equipment grounding conductor can result in electric shock. The conductor with the

green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of

the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a live terminal.

1. Examine extension cord before use. Make sure your extension cord is properly wired and in good condition.

Always replace a damaged extension cord or have it repaired by a qualiﬁed person before using it.

2. Do not abuse extension cord. Do not pull on cord to disconnect from receptacle; always disconnect by pulling on

plug. Disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.

Protect your extension cords from sharp objects, excessive heat and damp/wet areas.

3. Use a separate electrical circuit for your tool. This circuit must not be less than a 12-gauge wire and should be

protected with a 15A time-delayed fuse. Before connecting the motor to the power line, make sure the switch is in

the OFF position and the electric current is rated the same as the current stamped on the motor nameplate. Running

at a lower voltage will damage the motor.

product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

The table below shows the correct size to be used according to cord length and ampere rating. When in doubt, use

a heavier cord. The smaller the gauge number, the heavier the cord.

Fig. 1

UNPACKING

With the help of a friend or trustworthy foe, such as one of your in-laws, carefully remove the vacuum from the

packaging and place it on a sturdy, ﬂat surface. Make sure to take out all contents and accessories. Do not discard

the packaging until everything is removed. Check the packing list below to make sure you have all of the parts and

accessories. If any part is missing or broken, please contact customer service at 1-847-429-9263 (M-F 8-5 CST),

or email [email protected].

PACKING LIST

UNPACKING & PACKING LIST

Components

Hardware & Accessories

Hose

ST3.9x20 Screws (4)

Brush & Crevice Nozzle

Extension Tubes (2)

Wet Floor Brush

Carpet Brush (Pre-Installed)

Floor Brush

Wheel Assemblies (4)

Filter (Pre-Installed)

(Part No. VC4710-038)

Vacuum

KNOW YOUR WET / DRY VACUUM

TOOL PURPOSE

From general garage spring cleaning to major basement cleanup from ﬂooding or seepage, your wet / dry vacuum

can handle it all. Refer to the following diagrams to become familiarized with all the parts and controls of your

vacuum. The components will be referred to later in the manual for assembly and operation instructions.

WET / DRY VACUUM

Airﬂow Tab

Handle

Extension Tube

Hose

Side Tab

Extension Tube

Hose Connector

Utility Nozzle

Carrying Handle

Power Switch

Wheels

Dust Bucket

Floor Brush

Wet Floor Brush

Carpet Brush

Brush & Crevice Nozzle

Water Drain

Blower

ASSEMBLY & ADJUSTMENTS

ASSEMBLING THE VACUUM

1. Ensure the unit is unplugged from its power source and

the power switch is in the OFF position.

2. Pull out on the two side tabs (Fig. 1 - 1) and remove the

top cover of the vacuum (Fig. 1 - 2) to ﬁnd the additional

accessories inside the bucket (Fig. 1 - 3). Remove and set

them aside.

3. Turn the bucket upside down and assemble the four

wheel assemblies (Fig. 2 - 1) onto the bucket by inserting

them into the proper slots on the bucket and securing each

of them with a ST3.9x20 screw (Fig. 2 - 2).

4. Replace the top cover and attach the hose to either the

suction inlet (Fig. 3A - 1) or the blower outlet (Fig. 3B - 1)

depending on your desired use. Lock the hose by inserting

it into the respective port and twisting it about 1/8 turn

clockwise. The suction / blow function can be changed

easily by removing the hose and connecting it to the op-

posite port.

5. Extension tubes or accessories can be easily connected

to the end of the handle by ﬁrmly pressing and ﬁrmly twist-

ing the accessory to ensure a secure ﬁt (Fig. 4A - Fig. 4C).

Fig. 1

Fig. 2

Fig. 3A Fig. 3B

OPERATION

Fig. 4C

OPERATING THE VACUUM

1. The vacuum can be operated by turning on the switch

(Fig. 5 - 1).

2. Airﬂow can be adjusted using the tab on the hose (Fig.

6 - 1) to allow for maximum airﬂow when necessary and

lesser airﬂow in more delicate situations.

3. Ensure that the HEPA ﬁlter is installed during operation

of the unit.

NOTE: To install or remove the HEPA ﬁlter, refer to p. 12.

SWITCHING BETWEEN BRUSHES & NOZZLES

Your vacuum comes with a carpet brush, wet ﬂoor brush,

crevice nozzle, and bristle nozzle. You can switch between

accessories by following the steps in Fig. 4A - 4C.

1. The ﬂoor brush (Fig. 7 - 1) comes with the carpet brush

insert (Fig. 7 - 2) pre-installed. To switch brush operations,

remove the carpet brush insert and install the wet ﬂoor

brush insert (Fig. 7 - 3).

2. The brush and crevice nozzle (Fig. 7 - 4) has a bristle at-

tachment that can either be attached or removed based on

the job at hand. To vacuum in narrow, hard to reach places,

remove the bristle attachment. For vacuuming dirt and

dust off of furniture or blinds, use the bristle attachment.

Fig. 5

Fig. 6

Fig. 4A Fig. 4B

ASSEMBLY & ADJUSTMENTS

Fig. 7

MAINTENANCE

REMOVING DRY WASTE & CLEANING THE AIR FILTER

CAUTION! Always wear ANSI Z87.1-approved eye protection, as well as a NIOSH-approved respirator or

dust mask, when cleaning out the bucket or changing the ﬁlter. It is recommended to work outside, in an area

with sufﬁcient air ﬂow, when cleaning out the bucket or changing the ﬁlter.

1. Unplug the unit from the power source.

2. Remove the top vacuum cover and dispose of any waste

found in the bucket.

3. Unscrew the lock knob (Fig. 8 - 1) to release the HEPA

ﬁlter from the top of the vacuum.

4. Tap the ﬁlter against the inside of a garbage can to re-

move large particles of debris.

6. Use compressed air, or water from a garden hose, to re-

move ﬁne particles from the ﬁlter.

NOTE: Direct the compressed air or water outwards, spray-

ing from the inside of the ﬁlter towards the outside, as this

will produce the best results.

6. If using a garden hose, air dry the HEPA ﬁlter until it is

completely dry.

7. Re-install HEPA ﬁlter on the top vacuum cover and se-

cure it with the lock knob before operating the vacuum.

NOTE: Ensure all parts are completely dry before using the

vacuum for dry waste collection.

NOTE: After a while, depending on how heavily and fre-

quently the vacuum is used, the HEPA ﬁlter will not be able

to be cleaned sufﬁciently to provide continued effective per-

formance, and a new HEPA ﬁlter will need to be purchased.

Replacement HEPA ﬁlters can be found at wenproducts.

com under part number VC9209-044.

REMOVING AND CLEANING WET WASTE

1. Unplug the unit from the power source.

2. Remove the vacuum lid from the vacuum.

Fig. 8

3. Let the wet waste out through the water drain (Fig. 9 - 1) at the base of the dust bucket.

NOTE: For both wet and dry jobs, it is suggested to occasionally rinse the bucket with clean water to rid the vacuum

of any unwanted particles or critters, as well as to keep the vacuum fresh and its morale high. After all, its job quite

literally sucks.

Fig. 9

TROUBLESHOOTING GUIDE

Problem Cause Solution

Vacuum cleaner will not turn on

Plug is not connected to outlet.

Check the power cord and plug. Do

not use the unit if there is damage

to the cord.

Using wrong size or length of

extension cord.

Consult chart on p. 7. Use the

proper extension cord.

Worn carbon brushes.

Replace carbon brushes. Contact

customer service at 1-847-429-

9263, M-F 8-5 CST for assistance.

Power switch or motor is

defective.

Stop using the tool and contact cus-

tomer service at 1-847-429-9263,

M-F 8-5 CST for assistance.

Dust is ejected from the exhaust port

Filter is not installed or in-

stalled improperly.

Check ﬁlter installation and install

properly.

Filter is damaged. Replace the ﬁlter with a new ﬁlter.

Vacuum shows loss of suction

Hose is connected to blower

outlet. Connect hose to suction inlet.

Filter is clogged. Clean or replace the ﬁlter.

Vacuum bucket is full. Empty waste from bucket.

The hose connection is loose. Check hose connections and tighten

any lose attachments.

Top cover is improperly sealed

on the collector bucket.

Check seal. Make sure cover is se-

curely seated on collector bucket.

Damage to hose. Replace the hose.

WARNING! Stop using the generator immediately if any of the following problems occur or risk serious

personal injury. If you have any questions, please contact customer service at 1-847-429-9263 (M-F 8-5 CST),

or email [email protected].

EXPLODED VIEW & PARTS LIST

12345678910 11 12 13 14

27 28

30 31 32

394041

EXPLODED VIEW & PARTS LIST

No. Part No. Description Qty.

1 VC9209-001 Handle 1

2 VC9209-002 Handle Cover 2

3 VC9209-003 Top Inset Panel 1

4 VC9209-004 Screw 4

5 VC4710-002 Switch 1

6 VC9209-006 Top Cover 1

7 VC9209-007 Outlet Ring 1

8 VC9209-008 Outlet Air Valve 1

9 VC9209-009 Screw 2

10 VC9209-010 Blower Connector Base 1

11 VC9209-011 Screw 1

12 VC9209-012 Blower Connector 1

13 VC9209-013 Spring 1

14 VC9209-014 Blower Tube 2

15 VC9209-015 Front Inset 1

16 VC9209-016 Screw 2

17 VC9209-017 Inlet Cover 1

18 VC9209-018 Screw 1

19 VC9209-019 Upper Motor Foam 1

20 VC9209-020 Screw 1

21 VC9209-021 Middle Motor Foam 4

22 VC9209-022 Upper Motor Cover 1

23 VC9209-023 Screw 3

24 VC9209-024 Motor Middle Cover 1

25 VC9209-025 Screw 2

26 VC9209-026 Motor Base 1

27 VC9209-027 Locking Lever 1

28 VC9209-028 Motor Base Foam 1

29 VC9209-029 Motor Base Seal 1

30 VC4710-026 Suction Base 3

31 VC9209-031 Screw 1

32 VC4710-025 Suction Base Cover 1

33 VC9209-033 Darin Knob 1

34 VC9209-034 Drain Seal 1

35 VC9209-035 Darin Cap 1

No. Part No. Description Qty.

36 VC9209-036 Drain Cap Seal 4

37 VC9209-037 Screw 1

38 VC9209-038 Drain Bracket 4

39 VC9209-039 Caster Foot 4

40 VC4710-037 Caster 4

41 VC9209-041 Screw 1

42 VC9209-042 9.5-Gal. Tank 1

43 VC4710-040 Filter Knob 1

44 VC4710-039 Filter Seal 1

45 VC4710-038 HEPA Filter 1

46 VC4710-022 Filter Bracket 3

47 VC9209-047 Screw 1

48 VC4710-021 Bracket Seal 1

49 VC4710-020 Float 1

50 VC4710-019 Float Seal 6

51 VC9209-051 Heel Block 1

52 VC9209-052 Screw 1

53 VC9209-053 Foam Ring 3

54 VC9209-054 Screw 1

55 VC9209-055 Lower Motor Bracket 1

56 VC9209-056 Inlet Motor Seal 1

57 VC9209-057 Motor 2

58 VC9209-058 Motor Isolation Seal 1

59 VC9209-059 Motor Heat Seal 1

60 VC9209-060 Cord Clip 1

61 VC9209-061 Screw 1

62 VC9209-062 Power Cord Assembly 3

63 VC9209-063 Cable Ties 2

64 VC4710-041 Hose Assembly 1

65 VC9209-065 Floor Brush Assembly 1

66 VC9209-066 Crevice Brush Assembly 1

67 VC9209-067 Plastic Tube 2

68 VC4710-045 Tube Hook 1

69 VC9209-069 Screw 1

70 VC9209-070 Top Cover Seal 1

WARRANTY STATEMENT

V. 2022.09.16

WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this

commitment and our dedication to qualit

LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE

GRE

AT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN

consumer

power tools will be free from defects in material or workmanship during personal use for a period of two (2) years

used

for professional or commercial use. Purchaser has 30 days from the date of purchase to report missing or

damaged parts.

SELLER’S

SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent per-

mitted

by law, any warranty or condition implied by law, shall be the replacement of parts, without charge, which a

defective

in material or workmanship and which have not been subjected to misuse, alteration, careless handling,

misrepair

, abuse, neglect, normal wear and tear,

improper maintenance, or other conditions adversely affecting the

Product

or the component of the Product, whether by accident or intentionally, by persons other than Seller. To

make

a claim under this Limited Warranty, you must make sure to keep a copy of your proof of purchase that

clearly

dor

of Great Lakes Technologies, LLC. Purchasing through third party vendors, including but not limited to garage

sales,

pawn shops, resale shops, or any other secondhand merchant, voids the warranty included with this

product.

Contact [email protected] or 1-847-429-9263 with the following information to make arrangements:

your

shipping address, phone number, serial number, required part numbers, and proof of purchase. Damaged

defective parts and products may need to be sent to WEN before the replacements can be shipped out.

turning

a product for warranty service, the shipping charges must be prepaid by the purchaser. The product

must

shipped in its original container (or an equivalent), properly packed to withstand the hazards of shipment. The

product

must be fully insured with a copy of the proof of purchase enclosed. There must also be a description of

the

will be returned and shipped back to the pur

chaser at no charge for addresses within the contiguous United States.

THIS

LIMITED WARRANTY DOES NOT APPLY TO ITEMS THAT WEAR OUT FROM REGULAR USAGE OVER TIME,

INCLUDING

BELTS, BRUSHES, BLADES, BATTERIES, ETC. ANY IMPLIED WARRANTIES SHALL BE LIMITED IN

DUR

ATION TO TWO (2) YEARS FROM DATE OF PURCHASE. SOME STATES IN THE U.S. AND SOME CANADIAN

PROVINCES

DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMI-

TAT

ION MAY NOT APPLY TO YOU.

NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING

BUT

NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT.

SOME ST

ATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITAT

ION

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU.

THIS

LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS

WHICH

VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY

TO COUNT

RY.

THIS

LIMITED WARRANTY APPLIES ONLY TO ITEMS SOLD WITHIN THE UNITED STATES OF AMERICA, CANA-

AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER

COUNTRIES,

CONT

ACT THE WEN CUSTOMER SUPPORT LINE. FOR WARRANTY PARTS OR PRODUCTS REPAIRED UNDER

ARRANTY SHIPPING TO ADDRESSES OUTSIDE OF THE CONTIGUOUS UNITED STATES, ADDITIONAL

SHIPPING

CHARGES MAY APPLY.

9.25-GALLON ASPIRATEUR

EAU ET POUSSIÈRE

Instruction Manual

MODÈLE VC9209

IMPORTANT : Votre nouvel outil a été conçu et fabriqué selon les normes les plus élevées de WEN en matière

de ﬁabilité, de facilité d’utilisation et de sécurité de l’opérateur. Lorsqu’il est correctement entretenu, ce produit

vous fournira des années de performances robustes et sans problème. Portez une attention particulière aux

règles de fonctionnement en toute sécurité, aux avertissements et aux mises en garde. Si vous utilisez votre outil

correctement et conformément à sa destination, vous bénéﬁcierez d’années de service sûr et ﬁable.

BESOIN D’AIDE? NOUS CONTACTER!

Vous avez des questions sur les produits ? Besoin d’assistance technique ? N’hésitez pas à nous contacter:

TECHSUPPOR[email protected]1-847-429-9263 (M-F 8AM-5PM CST)

Pour les pièces de rechange et les manuels d’instructions les plus récents, visitez WENPRODUCTS.COM

Notre équipe de service client est anglophone.

CONTENU

BIENVENU 19

Introduction ................................................................................................... 19

Caractéristiques ............................................................................................. 19

SÉCURITÉ 20

Règles Générales de Sécurité ......................................................................... 20

Avertissements de Sécurité Aspirateur eau et Poussière................................ 22

Avertissements de Sécurité Électrique ........................................................... 23

Déballage et Liste de Colisage .........................................................................24

Connaître ton Aspirateur eau et Poussière ..................................................... 25

Montage & Réglages .......................................................................................26

AVANT D’OPÉRER

Opération ....................................................................................................... 27

Entretien ..........................................................................................................28

Guide de Dépannage .......................................................................................29

Vue Éclatée et Liste de Pièces .........................................................................30

Déclaration de Garantie .................................................................................. 32

OPÉRATION & ENTRETIEN

Pour acheter des pièces de rechange ou des accessoires pour votre outil, visitez WENPRODUCTS.COM

HEPA F9 Filtre de Remplacement (Partie VC4710-038)

CARACTÉRISTIQUES

Modèle VC9209

Moteur 1200W, 120V, 60 Hz, 10A

Capacité de poussière 9.25 Gallons (35 L)

Évaluation du Filtre HEPA F9 (Partie VC4710-038)

Dimensions du Produit 17.6 in. x 18.3 in. x 21.9 in.

Poids du Produit 24.25 Pounds

INTRODUCTION

Merci d’avoir Aspirateur eau et Poussière WEN. Nous savons que vous avez hâte de mettre votre outil au travail,

mais d’abord, veuillez prendre un moment pour lire le manuel. L’utilisation sécuritaire de cet outil exige que vous

lisiez et compreniez ce manuel de l’opérateur et toutes les étiquettes apposées sur l’outil. Ce manuel fournit des

informations concernant les problèmes de sécurité potentiels, ainsi que des instructions de montage et d’utilisation

utiles pour votre outil.

REMARQUE: Les informations de sécurité suivantes ne visent pas à couvrir toutes les conditions et situations pos-

sibles qui peuvent se produire. WEN se réserve le droit de modiﬁer ce produit et ses spéciﬁcations à tout moment

sans préavis.

Chez WEN, nous améliorons continuellement nos produits. Si vous trouvez que votre outil ne correspond pas ex-

actement à ce manuel, veuillez visiter wenproducts.com pour le manuel le plus à jour ou contactez notre service

client au 1-847-429-9263.

Conservez ce manuel à la disposition de tous les utilisateurs pendant toute la durée de vie de l’outil et revoyez-

le fréquemment pour maximiser votre sécurité et celle des autres.

SYMBOLE D’ALERTE DE SÉCURITÉ : Indique un danger, un avertissement ou une mise en garde. Les

symboles de sécurité et les explications qui les accompagnent méritent votre attention et votre compréhension.

Suivez toujours les consignes de sécurité pour réduire les risques d’incendie, de décharge électrique ou de

blessure. Cependant, veuillez noter que ces instructions et avertissements ne remplacent pas les mesures ap-

propriées de prévention des accidents.

RÈGLES GÉNÉRALES DE SÉCURITÉ

SÉCURITÉ DE LA ZONE DE TRAVAIL

1. Gardez la zone de travail propre et bien éclairée.

Les zones encombrées ou sombres invitent les acci-

dents.

2. N’utilisez pas d’outils électriques dans des atmo-

sphères explosives, comme en présence de liquides,

gaz ou poussières inﬂammables. Les outils électriques

créent des étincelles qui peuvent enﬂammer la poussière

ou les vapeurs.

3. Tenez les enfants et les passants éloignés lorsque

vous utilisez un outil électrique. Les distractions peu-

vent vous faire perdre le contrôle.

SÉCURITÉ ÉLECTRIQUE

1. Les ﬁches des outils électriques doivent corre-

spondre à la prise. Ne modiﬁez jamais la ﬁche de

quelque manière que ce soit. N’utilisez pas de ﬁches

d’adaptateur avec des outils électriques mis à la terre.

Des ﬁches non modiﬁées et des prises correspondantes

réduiront le risque de choc électrique.

2. Évitez tout contact corporel avec des surfaces mises

à la terre telles que des tuyaux, des radiateurs, des

cuisinières et des réfrigérateurs. Il existe un risque ac-

cru de choc électrique si votre corps est mis à la terre ou

mis à la terre.

3. N’exposez pas les outils électriques à la pluie ou à

l’humidité. L’eau entrant dans un outil électrique aug-

mentera le risque de choc électrique.

4. N’abusez pas le cordon. N’utilisez jamais le cordon

pour transporter, tirer ou débrancher l’outil électrique.

Gardez le cordon à l’écart de la chaleur, de l’huile,

des arêtes vives ou des pièces mobiles. Les cordons

endommagés ou emmêlés augmentent le risque de choc

électrique.

5. Lorsque vous utilisez un outil électrique à l’extérieur,

utilisez une rallonge adaptée à une utilisation en ex-

térieur. L’utilisation d’un cordon adapté à une utilisation

en extérieur réduit le risque de choc électrique.

6. S’il est inévitable d’utiliser un outil électrique dans

un endroit humide, utilisez une alimentation protégée

par un disjoncteur de fuite à la terre (GFCI). L’utilisation

d’un GFCI réduit le risque de choc électrique.

SÉCURITÉ PERSONNELLE

1. Restez vigilant, surveillez ce que vous faites et

faites preuve de bon sens lorsque vous utilisez un outil

électrique. N’utilisez pas un outil électrique lorsque

vous êtes fatigué ou sous l’inﬂuence de drogues,

d’alcool ou de médicaments. Un moment d’inattention

lors de l’utilisation d’outils électriques peut entraîner des

blessures graves.

2. Utiliser un équipement de protection individu-

elle. Portez toujours des lunettes de protection.

L’équipement de protection tel qu’un masque respira-

toire, des chaussures de sécurité antidérapantes et une

protection auditive utilisé dans les conditions appro-

priées réduira le risque de blessures.

3. Empêcher le démarrage involontaire. Assurez-vous

que l’interrupteur est en position d’arrêt avant de

brancher la source d’alimentation et/ou la batterie, de

prendre ou de transporter l’outil. Le transport d’outils

électriques avec votre doigt sur l’interrupteur ou la mise

sous tension d’outils électriques dont l’interrupteur est

activé invite les accidents.

4. Retirez toute clé ou clé de réglage avant de mettre

l’outil électrique en marche. Une clé ou une clé laissée

attachée à une partie rotative de l’outil électrique peut

entraîner des blessures corporelles.

La sécurité est une combinaison de bon sens, de vigilance et de connaissance du fonctionnement de votre article.

Le terme “outil électrique” dans les avertissements fait référence à votre outil électrique (avec ﬁl) alimenté par le

secteur ou à votre outil électrique (sans ﬁl) alimenté par batterie.

CONSERVER CES CONSIGNES DE SÉCURITÉ.

AVERTISSEMENT! Lisez tous les avertissements de sécurité et toutes les instructions. Le non-respect des

avertissements et des instructions peut entraîner un choc électrique, un incendie et/ou des blessures graves.

La page charge ...

Wen VC9209 Manuel utilisateur

Marque: Wen

Modèle: VC9209

Catégorie: Aspirateurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Wen VC9209 User manual

Wen VC9209 Manuel utilisateur

Wen VC9209 Manuel utilisateur

dans d''autres langues

Autres documents