TP-LINK CPE510 Guide d'installation

Installation Guide

Outdoor CPE

CPE210 / CPE220 / CPE510 / CPE520

Contents

Overview 01

Hardware Connection 04

Site Consideration 04

Connection and Installation 06

Lightning & ESD Protection 08

Software Conguration 10

Logging in to the PharOS 10

Typical Application Conguration 12

Antenna Alignment 14

Specications 15

FAQ 16

01

Overview

TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless

network solutions. This guide is applicable to products including CPE210,

CPE220, CPE510 and CPE520.

• Package Contents

Installation Guide

Outdoor CPE

CPE210 / CPE220 / CPE510 / CPE520

Pharos CPE

Passive PoE

Adapter

Pole Mounting

Straps

Mounting Bracket

Plastic Wall Anchors (Qty.2)

Self-tapping Screws (Qty.2)

Installation Guide

Power Cord

• LED Explanation

The following picture takes CPE520 as an example.

POWERLAN0LAN1

AP/AP Router mode:

All four LEDs remain solid.

Client/Bridge/Repeater/AP Client Router mode:

That the more LEDs lit will indicate better wireless signal strength.

Flashing: A device is connected to this port, and is active.

On: The CPE is powered on.

On: A device is connected to this port, but there is no activity.

02

• Panel Layout

Pharos CPE220

/

CPE520:

Shielded Ethernet

Port LAN0 (Passive

PoE in)

RESETShielded Ethernet

Port LAN1

Grounding

Terminal

Pharos CPE210

/

CPE510:

Shielded Ethernet Port

LAN (Passive PoE in)

Grounding

Terminal

RESET

03

Passive PoE Adapter:

Remote Reset

Press and hold for 8 seconds to

reset the CPE to its factory defaults.

Power LED

The Power LED is on when the

passive PoE adapter is working

normally.

04

Hardware Connection

1. Site Consideration

• Mounting Height

Ensure a clear line of sight between the wireless devices for an optimum

performance. An elevated location is recommended as obstacles like

trees, buildings and large steel structures will weaken the wireless signal.

See 'Q2' in 'FAQ' for details about how to calculate the minimum mounting

height of the devices.

Line of Sight

Side View

05

• Orientation

Install the CPE devices with the front facing the intended signal receiving

devices. You can orient the devices with the assistance of Google Maps,

GPS and some landmarks according to the horizontal beamwidth listed

below.

Models CPE210 CPE220 CPE510 CPE520

Horizontal Beamwidth 65° 60° 45° 45°

A

shenzhen

B

Line of Sight

Horizontal

Beamwidth

06

2. Connection and Installation

Connect and mount the CPE and power adapter as shown below. The

following introduction takes CPE520 as an example.

• Connecting CPE and Power Adapter

Connect the CPE and power adapter as shown in the gure below.

Ethernet cable length up to 60m

You should prepare an adequate

Ethernet cable to connect the CPE

and the passive PoE adapter.

Shielded CAT5e (or above) cable

with ground wire is recommended

(refer to the next section).

Connect to a computer,

router or switch.

(Depending on your

intended usage and/or

network topology.)

Slide to replace the cover

of the CPE when all

connections are nished.

LAN0

PoE

LAN

07

• Mounting CPE

At the selected site, approximately align the CPE to the direction that you

have oriented.

• Mounting Power Adapter (Optional)

Follow the steps below to mount the power adapter:

To ensure the passive PoE adapter is attached most securely, it is

recommended to install the adapter with the Ethernet port facing upward.

1. Drill two holes on the wall and insert the plastic wall anchors into the

the holes. Secure the mounting bracket to the wall. Make sure the

shoulders at the corners of the mounting bracket are on the outside

and pointing upward.

2. Attach the passive PoE adapter to the mounting bracket by sliding

the adapter in the direction of the arrows until it locks into place.

08

3. Lightning & ESD Protection

Proper grounding is extremely important for outdoor devices.

By using shielded CAT5e (or above) cable with ground wire for the

connection and the provided PoE adapter (method

1

), you can eectively

eliminate ESD attacks. If you use the general CAT5e cable for the

connection, then it is necessary to connect the grounding terminal of the

CPE to earth ground through grounding cable (method

2

).

The following introduction takes CPE520 as an example.

CPE

Grounding

Terminal

Earth Ground

Two Methods:

2

1

PoE Adapter with

Earth Ground

Grounding

Cable

Shielded CAT5e (or above) Cable

with Ground Wire

Grounding Terminal and Cable

Shielded CAT5e (or above)

Cable with Ground Wire

Grounded 3-wire

Power Outlet

09

Twisted Pair

Ground Wire

Shielded RJ45 Connector

Secondary Cable Shield

Cable Shield

Sheath

Shielded CAT5e (or above) Cable with Ground Wire

10

Software Conguration

This chapter introduces the login to the PharOS Web Interface and the

software congurations.

1. Logging in to the PharOS

1. Before accessing the PharOS Web Interface, you need to assign

a static IP address 192.168.0.X (X ranges between 2 and 253, e.g.

192.168.0.10) to your computer.

2. Open a web browser, type http://192.168.0.254 into the address eld

and press Enter (Windows) or return (Mac). It is recommended to use

the latest version of Google Chrome, Firefox or Safari.

11

3. Enter admin for both User Name and Password. Read and agree the

terms of use, then click Login.

4. Change the default User Name and Password to protect your CPE.

Let’s start conguring the CPE.

For subsequent logins, use the new username and password.

For more congurations, please visit http://www.tp-link.com/support to

download the User Guide of PharOS products in the download center.

12

2. Typical Application Conguration

The typical topology is as follows. A wireless bridge is built between two

locations that are far from each other. Follow the instructions below to

congure the Access Point and the Client.

Access Point Client

Computer

IP camera

LAN: 192.168.0.254 LAN: 192.168.0.2

Congure the Access Point (AP)

1. Log in to PharOS and go to the Quick Setup page.

2. Operation Mode: Select Access Point and click Next.

3. LAN Settings: Click Next.

4. Wireless AP Settings:

a. Create a new SSID (Network name) for your wireless network.

b. Select WPA-PSK/WPA2-PSK for the Security method and create

a PSK Password to protect your AP.

c. Enter the distance between the Access Point and the Client into

the Distance Setting eld.

d. Select the MAXtream checkbox (Refer to Q3 in FAQ for details

about MAXtream), and click Next.

5. Finish: Verify your settings and click Finish to complete the

conguration.

Congure the Client

1. Log in to PharOS and go to the Quick Setup page.

2. Operation Mode: Select Client and click Next.

13

3. LAN Settings: Change the IP Address to 192.168.0.X (X ranges

between 2 and 253), the same subnet with the access point, and

click Next.

4. Wireless Client Settings:

a. Click Survey and select the SSID of the Access Point in the AP list,

then click Connect.

b. Select WPA-PSK/WPA2-PSK from the Security option, enter the

same PSK password and distance value of the Access Point, then

click Next.

5. Finish: Verify your settings and click Finish to complete the

conguration.

For more congurations, please visit http://www.tp-link.com/support to

download the User Guide of PharOS products in the download center.

14

Antenna Alignment

In order to get the best performance, you can precisely align the direction

of the CPE with the assistance of Wireless Signal Quality on

STATUS page of the PharOS Web Interface.

Adjust the direction of the CPE until the

device reaches the highest SNR.

WISP

15

Specications

HARDWARE FEATURES

Dimensions

CPE520/CPE220: 275.83*79*60.3mm

CPE510/CPE210: 224.34*79*60.3mm

Interface

CPE520/CPE220 CPE510/CPE210

LAN0: 10/100Mbps

Ethernet Port (PoE IN)

LAN1: 10/100Mbps

Ethernet Port

LAN: 10/100Mbps

Ethernet Port (PoE IN)

GND: Grounding Terminal for Lightning Protection

RESET: Button to restore the device to Factory

Default

Power Supply

24V Passive PoE Adapter Included

ESD Protection

1

15kV

Lightning Protection

1

Up to 6kV

Operating

Temperature

-40

℃

to

70

℃

(-40

℉

to 158

℉

)

Operating Humidity 10% to 90%

Certication CE, FCC, RoHS, IP55

WIRELESS FEATURES

Models CPE210 CPE220 CPE510 CPE520

Antenna Gain 9dBi 12dBi 13dBi 16dBi

Horizontal

Beamwidth/Elevation

Beamwidth

2

65°/ 35° 60°/ 30° 45°/ 30° 45°/ 30°

802.11 Standards 11b/g/n 11b/g/n 11a/n 11a/n

Note:

1. Estimation is based on copper grounding cable and shielded CAT5e cable

with ground wire.

2. Beamwidth values may vary throughout operating frequency.

16

FAQ

Q1. How to restore the CPE to its factory default

settings?

With the CPE powered on, press and hold the RESET button on the

CPE or the Remote Reset button on the passive PoE adapter for

about 8 seconds until the Wireless Signal Strength LEDs ash.

Method 1:

The following picture takes CPE520 as an example.

RESET Button

Press & hold for about 8

seconds

Method 2:

Remote Reset Button

Press & hold for about 8 seconds

17

Q2. How to calculate the minimum mounting height

of the devices?

In order to maximize the received signal strength of the devices,

installers need to minimize the eect of the out-of-phase signals,

which is caused by obstacles in the path between the transmitter

and the receiver. Fresnel Zone is a usual method to calculate this

path, as shown in the formula and the gure below.

h = the height of

obstacle at this point

H h+r

*

(1 40%)

(H is the height of the CPE)

d2

r

d1

where,

r = Fresnel zone radius in meters

c = 3x10

8

m/s, speed of light

f = operating frequency of the devices in

Hz

d1 & d2 = the distances between the

point and the devices in meters

f

c

dd

r ⋅

+

×

=

21

For example, assume d1 is 2km, d2 is 8km, and f is 2.4GHz, then

r would be 14.142m. Considering a toleration of 40%, allowable

radius would be 8.485m. Assume h is 10m, then the result of the

minimum mounting height based on this point would be 18.485m.

Similarly, calculate the results based on all the points where there are

obstacles, and the maximum value would be the nal result.

For more information, please refer to:

http://en.wikipedia.org/wiki/Fresnel_zone

La page charge ...

TP-LINK CPE510 Guide d'installation

TP-LINK CPE510 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents