Wacker Neuson DS70 Manuel utilisateur

Taper
Manuel utilisateur
Operator’s Manual
Notice d'emploi
Vibratory Rammer
Pilonneuse
DS70
Type DS70
Document 5200023299
Date 1216
Version 02
Langue EN-FR
5200023299
Copyright notice
© Copyright 2016 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operators Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
DS70 Foreword
wc_tx003636gb_FM10.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
;
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
If you are missing either of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Machine Item Number
DS70 5200010976
wc_gr011691
Serial Number:
Foreword DS70
4 wc_tx003636gb_FM10.fm
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change any
portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental
discharge of sparks or flames from the engine exhaust. Spark arresters are
qualified and rated by the United States Forest Service for this purpose. In order to
comply with local laws regarding spark arresters, consult the engine distributor or
the local Health and Safety Administrator.
Manufacturers
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
Table of Contents
DS70
wc_bo5200017628_02_FM10TOC.fm
5
Foreword 3
1 Safety Information 7
1.1 Signal Words Used in this Manual ....................................................... 7
1.2 Machine Description and Intended Use ............................................... 8
1.3 Safety Guidelines for Operating the Machine ....................................... 9
1.4 Safety Guidelines for Lifting the Machine ........................................... 10
1.5 Service Safety .................................................................................... 11
1.6 Operator Safety while Using Internal Combustion Engines ............... 13
2 Labels 14
2.1 Label Locations .................................................................................. 14
2.2 Label Meanings .................................................................................. 15
3 Lifting and Transporting 18
3.1 Lifting the Rammer ............................................................................. 18
3.2 Transporting the Rammer .................................................................. 19
4 Operation 20
4.1 Preparing the Machine for First Use ................................................... 20
4.2 Recommended Fuel ........................................................................... 21
4.3 Refueling the Machine ........................................................................ 22
4.4 Position of the Operator ..................................................................... 23
4.5 Before Starting ................................................................................... 23
4.6 Starting, Operating, and Stopping the Machine ................................. 24
4.7 Emergency Shutdown Procedure ....................................................... 26
4.8 Optional Equipment ............................................................................ 26
Table of Contents
DS70
6
5 General Maintenance 27
5.1 Maintaining the Emission Control System ..........................................27
5.2 Periodic Maintenance Schedule .........................................................28
5.3 Checking and Changing the Ramming System Oil .............................29
5.4 Checking the Fuel Lines and Fittings ..................................................31
5.5 Maintaining the Shoe Hardware .........................................................32
5.6 Inspecting the Machine .......................................................................33
5.7 Inspecting and Cleaning the Fuel Filter ..............................................34
5.8 Replacing the In-Line Fuel Filter .........................................................35
5.9 Long-Term Storage .............................................................................36
5.10 Machine Disposal / Decommissioning ................................................37
6 Engine Maintenance: Hatz 1B 20 / 1B 30 38
7 Troubleshooting 41
8 Technical Data 42
8.1 DS70 ...................................................................................................42
8.2 Sound Measurements .........................................................................43
8.3 Vibration Measurements .....................................................................43
8.4 Dimensions .........................................................................................43
wc_si000850gb_FM10.fm
7
DS70 Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
To avoid death or serious injury from this type of hazard, obey all safety mes-
sages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000850gb_FM10.fm
8
Safety Information DS70
1.2 Machine Description and Intended Use
This machine is a vibratory rammer. The Wacker Neuson Rammer consists of a
gasoline or diesel engine, a clutch, a fuel tank, a spring-loaded ramming system, a
ramming shoe, and a handle. The engine transmits power through the ramming
system and ramming shoe, generating percussive impact force to compact soil.
The operator guides and controls the machine from behind using the handle.
This machine is intended to be used for compacting cohesive, mixed, and granular
soils in confined areas.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine as a hammer or for other demolition work
Attaching the machine to any other machine
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operators Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Fire hazards from improper refueling techniques
Fuel and its fumes
Personal injury from improper lifting techniques or operating techniques
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
wc_si000850gb_FM10.fm
9
DS70 Safety Information
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
Have received instruction on how to properly use the machine
Are familiar with required safety devices
The machine must not be accessed or operated by:
Children
People impaired by alcohol, drugs or prescription drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Identify whether special hazards exist in the application area, such as toxic
gases or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
Be aware of the application area.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
wc_si000850gb_FM10.fm
10
Safety Information DS70
Safe
operating
practices
When operating this rammer:
Remain aware of the rammer’s moving parts. Keep hands, feet, and loose
clothing away from the rammer’s moving parts.
When working near the edges of pits, slopes, trenches, and platforms, always
operate the rammer in such a way that there is no possibility of it tipping over or
falling in.
When operating this rammer:
Do not operate a rammer in need of repair.
Do not tamper with or disable the function of the operating controls.
Do not leave the rammer running unattended.
Do not consume the operating fluids used in this machine. Depending on your
machine model, these operating fluids may include water, wetting agents, fuel
(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,
heat transfer fluid (propylene glycol with additives), battery acid, or grease.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
After use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when the machine is not
being operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean location out of the reach of children.
1.4 Safety Guidelines for Lifting the Machine
When lifting the machine:
Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any
other type of lifting device used is attached securely and has enough weight-
bearing capacity to lift or hold the machine safely. See chapter Technical Data
for machine weight.
Remain aware of the location of other people when lifting the machine.
Only use the lifting points and tie-downs described in the Operator’s Manual.
Make sure the transporting vehicle has sufficient load capacity and platform size
to safely transport the machine.
To reduce the possibility of injury:
Do not stand under the machine while it is being lifted or moved.
Do not get onto the machine while it is being lifted or moved.
wc_si000850gb_FM10.fm
11
DS70 Safety Information
1.5 Service Safety
Service
training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered with
the machine.
Familiarize yourself with the location and proper use of all controls and
protective devices.
Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow untrained or improperly trained people to service or maintain the
machine. Personnel servicing or maintaining the machine must be familiar with
the associated potential risks and hazards.
Maintenance items that can be performed by the operator are listed in this
manual. Other repairs should be performed by a qualified technician. Repairs
can be hazardous if not performed correctly. Contact your Wacker Neuson
dealer service department for additional information or for repairs to your
machine.
Precautions
When servicing or maintaining the machine:
Read and understand the service procedures before performing any service to
the machine.
All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Re-install the safety devices and guards after repair and maintenance
procedures are complete.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
wc_si000850gb_FM10.fm
12
Safety Information DS70
Cleaning
When cleaning and servicing the machine:
Keep machine clean and free of debris such as leaves, paper, cartons, etc.
Keep labels legible.
Clean with soapy water only.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
Safe service
practices
Do not alter engine speeds. Run the engine only at speeds specified in
Technical Data.
Do not operate the machine without an air cleaner.
wc_si000850gb_FM10.fm
13
DS70 Safety Information
1.6 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
Keep the area around the exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
When running the engine:
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Re-install the fuel tank cap after refueling.
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
Use suitable tools for refueling (for example, a fuel hose or a funnel).
Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.
Static electricity can ignite the fuel or fuel vapors.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through such items as exhaust fans or hoses.
wc_si000851gb_FM10.fm
14
Labels DS70
2 Labels
2.1 Label Locations
wc_gr011692
A
B
C
D
E
F
G
G
H
wc_si000851gb_FM10.fm
15
DS70 Labels
2.2 Label Meanings
A
To start the machine:
1. Open the fuel valve.
2. Place the throttle in the SLOW / IDLE
position.
3. Pull the starter rope until engine starts.
To stop the machine:
1. Move the throttle lever to the OFF position.
2. Close the fuel valve.
Warning! To reduce the risk of hearing loss,
always wear hearing protection when operating
this machine.
Read the operator’s manual.
Danger!
Asphyxiation hazard.
Engines emit carbon monoxide.
Do not run the machine indoors or in an
enclosed area unless adequate ventilation,
through such items as exhaust fans or
hoses, is provided.
No sparks, flames, or burning objects near
the machine.
Stop the engine before refueling.
This machine uses diesel fuel.
wc_sy0180930
wc_sy0118647
wc_si000851gb_FM10.fm
16
Labels DS70
B WARNING
Springs are compressed. Release cover slowly to
avoid spring ejection.
See the Repair Manual for proper disassembly
instructions.
C Guaranteed sound power level in dB(A)
D Turtle = Idle/slow engine speed
Rabbit = Full/fast engine speed
AVERTISSEMENTAVERTISSEMENT
Los resortes son comprimidos. Con el fin de evitar
la expulsion de los resortes, consulte el Manual de
Reparaciones para las instrucciones de desmontaje
correcto.
The springs are compressed. In order to avoid ejection
of the springs, refer to Repair Manual for proper
disassembly instructions.
Les ressorts sont sous pression. Afin d'eviter
l'ejection des ressorts, consulter le Manuel de
Reparation pour les instructions de demontage correct.
ADVERTENCIAADVERTENCIA
118859118859
WARNINGWARNING
52000003145200000314
wc_si000851gb_FM10.fm
17
DS70 Labels
E WARNING
Hot surface
F WARNING
Operation of this equipment may create sparks that
can start fires around dry vegetation. A spark
arrester may be required. The operator should
contact local fire agencies for laws or regulations
relating to fire prevention requirements.
G NOTICE
Lifting point
H Ultra low sulfur fuel only.
WARNUNGWARNUNG
ADVERTENCIAADVERTENCIA
WARNINGWARNING
AVERTISSEMENTAVERTISSEMENT
117037117037
178732178732
WARNING
Operation of This Equipment May Create Sparks That Can Start Fires Around Dry
Vegetation. A Spark Arrestor May be Required. The Operator Should Contact Loca
Fire Agencies For Laws or Regulations Relating to Fire Prevention Requirements.
Per CAL. PRC. CODE
NOTICE
ULTRA LOW SULFUR FUEL ONLY
SOLAMENTE COMBUSTIBLE DE
ULTRABAJO CONTENIDO DE AZUFRE.
SEULEMENT CARBURANT DE
SOUFRE ULTRA BAS.
AVISO
AVIS
ULSD-S15
5100030871
wc_tx003637gb_FM10.fm
18
Lifting and Transporting DS70
3 Lifting and Transporting
3.1 Lifting the Rammer
Requirements
Lifting device (crane or hoist) capable of supporting the rammer’s weight (see
the identification plate on the rammer)
Lifting gear (hooks, slings, and/or chains) capable of supporting the rammer’s
weight
Engine stopped and cool to the touch
Procedure
Perform the procedure below to lift the rammer.
1. Attach the lifting gear to the central lifting cable (a).
2. Lift the rammer a short distance, making sure that all connections are secure.
3. Continue lifting the rammer as required.
WARNING
Crushing hazard. Do not use the guide handle (b) to lift the rammer.
Use only the central lifting cable to lift the rammer.
WARNING
Crushing hazard. Do not use the central lifting cable if there are any signs of cut
wires, excessive wear, or other defects.
Always inspect the central lifting cable for wear, damage, or abuse. Replace a
damaged lifting cable immediately.
Protect the central lifting cable from all sharp edges.
wc_tx003637gb_FM10.fm
19
DS70 Lifting and Transporting
3.2 Transporting the Rammer
Overview
This rammer can be transported in a vehicle, or manually, depending on job site
conditions and distance to be traveled.
NOTICE: Do not tow this rammer.
Requirements
Engine stopped and cool to the touch
Lifting devices and gear
Fuel tank drained (if transporting horizontally)
Transporting
in a vehicle
Perform the procedure below to transport the rammer in a vehicle.
1. Lift the rammer into the transport vehicle. See topic Lifting the Rammer.
2. Secure the rammer to the transport vehicle in the upright position to prevent it
from tipping, falling, or rolling.
If the rammer cannot be secured in the upright position,
a.Drain the fuel tank to prevent fuel from leaking from the cap (c).
b.
Lay the rammer down only as shown and tie it to the vehicle at points
(a)
and
(b)
.
Transporting
manually
Rollers (d) enable the rammer to be rolled from one location to another. Perform
the procedure below to transport the rammer manually.
1. Drain the fuel tank to prevent fuel leaking from the cap.
2. Lay the rammer down as shown.
3. Raise the rammer by the lifting handle (b).
4. Roll the rammer forward or backward as needed.
WARNING
Lifting injury. This machine is too heavy to lift without mechanical assistance.
Do not attempt to lift or carry the rammer without using appropriate lifting
devices and gear as described in topic Lifting the Rammer.
wc_gr011694
a
d
c
b
wc_tx003638gb_FM10.fm
20
Operation DS70
4 Operation
4.1 Preparing the Machine for First Use
1. Make sure all loose packaging materials have been removed from the machine.
2. Check the machine and its components for damage. If there is visible damage,
do not operate the machine! Contact your Wacker Neuson dealer immediately
for assistance.
3. Take inventory of all items included with the machine and verify that all loose
components and fasteners are accounted for.
4. Attach component parts not already attached.
5. Add fluids as needed and applicable, such as fuel and engine oil.
6. Move the machine to its operating location.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Wacker Neuson DS70 Manuel utilisateur

Taper
Manuel utilisateur