Empire Comfort Systems Furnace FAW-40-1SPP Manuel utilisateur

Marque: Empire Comfort Systems

Modèle: Furnace FAW-40-1SPP

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

12427-2-0903

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER'S MANUAL

FAN TYPE

VENTED

WALL FURNACE

MODEL

FAW-40-1SPP

FAW-40-1IP

EFFECTIVE DATE

SEPTEMBER 2003

WARNING: If the information in this

manual is not followed exactly, a fire or

explosion may result causing property

damage, personal injury or loss of life.

— Do not store or use gasoline or other

flammable vapors and liquids in the vi-

cinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor's phone. Follow the

gas supplier's instructions.

• If you cannot reach your gas supplier,

call the fire department.

— Installation and service must be per-

formed by a qualified installer, service

agency or the gas supplier.

WARNING: If not installed, operated and

maintained in accordance with the manu-

facturer's instructions, this product could

expose you to substances in fuel or from

fuel combustion which can cause death or

serious illness.

Installer: Please leave these instructions with the

consumer.

Consumer: Please retain these instructions for

future use.

12427-2-0903

Page 2

The base referred to above does not mean the fire-proof base as used on

wood stoves. The protection is for rugs that are extremely thick and light

colored tile.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed so that

all burners and burner ignition devices are located not less than 18"

(457mm) above the floor.

Such equipment shall be located, or protected, so it is not subject to

physical damage by a moving vehicle.

Specifications

Model FAW-40SPP FAW-40IP

Input BTU/HR (KW/H) 40,000 (11.7) 40,000 (11.7)

Height 72 1/2" (184.2cm) 72 1/2" (184.2cm)

Width 14 1/8" (35.9mm) 14 1/8" (35.9mm)

Depth 10 3/8" (26.4mm) 10 3/8" (26.4mm)

Gas Inlet Pipe 1/2" (1.27cm) 1/2" (1.27cm)

Vent Collar Type B Oval 4" (10.2cm) 4" (10.2cm)

CFM 275 275

Accessories

Side outlet, 10" (254mm) SOK-1

maximum extension, fixed register

Rear Outlet, 10" (254mm) ROK-1

maximum extension, adjustable register

Vent enclosure, 24" (61cm) FVE-24

[for rooms up to 96 1/2" (245cm) in height]

Vent enclosure, 34" (86cm) FVE-34

[for rooms up to 106 1/2" (270.5cm) in height]

Vent enclosure, 46" (117cm) FVE-46

[for rooms up to 118 1/2" (301cm) in height]

Oval-to-Round flue adapter kit 4" (102mm) DV-648

Introduction

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of a vented wall

furnace.

Instructions to Installer

1. Installer must leave instruction manual with owner after installation.

2. Installer must have owner fill out and mail warranty card supplied

with furnace.

3. Installer should show owner how to start and operate furnace and

thermostat.

Warning:

Any change to this furnace or its control can be dangerous. This

is a heating appliance and any panel, door or guard removed

for servicing an appliance must be replaced prior to operating

the appliance.

General Information

This series is design certified in accordance with American National

Standard / CSA Standard Z21.86 and CSA 2.32 by the Canadian

Standards Association, as a Fan Type Vented Wall Furnace and must be

installed according to these instructions.

Any alteration of the original design, installed other than as shown

in these instructions or use with a type of gas not shown on the rating

plate is the responsibility of the person and company making the

change.

Important

All correspondence should refer to complete Model No., Serial No. and

type of gas.

Notice: During initial firing of this unit, its paint will bake out and smoke

will occur. To prevent triggering of smoke alarms, ventilate the room in

which the unit is installed.

Installation on Rugs and Tile

If this appliance is installed directly on carpeting, tile or other combustible

material other than wood flooring the appliance shall be installed on a

metal or wood panel extending the full width and depth of the appliance.

the flow of combustion and ventilation air.

• DO keep the appliance area clear and free from combustible

material, gasoline and other flammable vapors and liquids.

• DO examine venting system periodically and replace dam-

aged parts.

• DO make a periodic visual check of pilot and burners. Clean

and replace damaged parts.

• CAUTION: Pilot hole cover must be kept tightly closed

during operation.

• DO NOT use this heater if any part has been under water.

Immediately call a qualified service technician to inspect the

heater and to replace any part of the control system and any

gas control which has been under water.

• This furnace must not be connected to a chimney flue serving

a separate solid-fuel burning appliance.

• IMPORTANT: This furnace has a washable permanent

type filter in the door which should be cleaned at least once

per year before the heating season. For dirty or high use

areas more frequent cleaning is required.

• Due to high temperatures the appliance should be located out

of traffic and away from furniture and draperies.

• Children and adults should be alerted to the hazards of high

surface temperatures and should stay away to avoid burns or

clothing ignition.

• Young children should be carefully supervised when they are

in the same room as the appliance.

• Clothing or other flammable material should not be placed on

or near the appliance.

• Any safety screen or guard removed for servicing an appliance

must be replaced prior to operating the appliance.

• Keep burner and control compartment clean.

• Installation and repair should be done by a QUALIFIED

SERVICE PERSON. The appliance should be inspected

before use and at least annually by a qualified service person.

More frequent cleaning may be required due to excessive lint

from carpeting, bedding materials, etc. It is imperative that

control compartments, burners and circulating air passage-

ways of the appliance be kept clean.

• DO NOT put anything around the furnace that will obstruct

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANELS INSTALLED.

12427-2-0903

Page 3

Some people cannot smell well. Some people cannot smell

the odor of the chemical stench put into the gas. You must

find out if you can smell the odorant in propane. Smoking can

decrease your ability to smell. Being around an odor for a time

can affect your sensitivity or ability to detect that odor. Some-

times other odors in the area mask the gas odor. People may not

smell the gas odor or their minds are on something else. Think-

ing about smelling a gas odor can make it easier to smell.

The odorant in LP-gas is colorless, and it can fade under

some circumstances. For example, if there is an underground

leak, the movement of the gas through soil can filter the odorant.

Odorants in LP-Gas also are subject to oxidation. This fading

by point with the members of your household. Someday

when there may not be a minute to lose, everyone's safety will

depend on knowing exactly what to do. If, after reading the

following information, you feel you still need more informa-

tion, please contact your gas supplier.

Propane (LP-Gas) is a flammable gas which can cause fires

and explosions. In its natural state, propane is odorless and

colorless. You may not know all the following safety precau-

tions which can protect both you and your family from an

accident. Read them carefully now, then review them point

can occur if there is rust inside the storage tank or in iron gas

pipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That

will take some of the odorant out of the gas, reducing its odor

intensity.

LP-Gas may stratify in a closed area, and the odor intensity could

vary at different levels. Since it is heavier than air, there may be

more odor at lower levels. Always be sensitive to the slightest

gas odor. If you detect any odor, treat it as a serious leak.

Immediately go into action as instructed earlier.

• Learn to recognize the odor of LP-gas. Your local LP-Gas

Dealer can give you a "Scratch and Sniff" pamphlet. Use it

to find out what the propane odor smells like. If you suspect

that your LP-Gas has a weak or abnormal odor, call your LP-

Gas Dealer.

• If you are not qualified, do not light pilot lights, perform

service, or make adjustments to appliances on the LP-Gas

system. If you are qualified, consciously think about the odor

of LP-Gas prior to and while lighting pilot lights or perform-

ing service or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the LP-Gas odor. Do not try to light

pilot lights, perform service, or make adjustments in an area

where the conditions are such that you may not detect the

odor if there has been a leak of LP-Gas.

• Odor fade, due to oxidation by rust or adsorption on walls of

new cylinders and tanks, is possible. Therefore, people

should be particularly alert and careful when new tanks or

cylinders are placed in service. Odor fade can occur in new

tanks, or reinstalled old tanks, if they are filled and allowed

to set too long before refilling. Cylinders and tanks which

have been out of service for a time may develop internal rust

which will cause odor fade. If such conditions are suspected

to exist, a periodic sniff test of the gas is advisable. If you

have any question about the gas odor, call your LP-gas

dealer. A periodic sniff test of the LP-gas is a good safety

measure under any condition.

• If, at any time, you do not smell the LP-Gas odorant and you

think you should, assume you have a leak. Then take the

same immediate action recommended above for the occasion

when you do detect the odorized LP-Gas.

• If you experience a complete "gas out," (the container is

under no vapor pressure), turn the tank valve off immedi-

ately. If the container valve is left on, the container may draw

in some air through openings such as pilot light orifices. If

this occurs, some new internal rusting could occur. If the

valve is left open, then treat the container as a new tank.

Always be sure your container is under vapor pressure by

turning it off at the container before it goes completely empty

or having it refilled before it is completely empty.

SAFETY INFORMATION FOR USERS OF LP-GAS

• Do not operate electric switches, light matches, use your

phone. Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• LP-Gas is heavier than air and may settle in low areas such

as basements. When you have reason to suspect a gas leak,

keep out of basements and other low areas. Stay out until

firefighters declare them to be safe.

• Use your neighbor's phone and call a trained LP-Gas service

person and the fire department. Even though you may not

continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and firefighters check for

escaped gas. Have them air out the area before you return.

Properly trained LP-Gas service people should repair the

leak, then check and relight the gas appliance for you.

SOME POINTS TO REMEMBER

NO ODOR DETECTED - ODOR FADE

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.

That's your signal to go into immediate action!

12427-2-0903

Page 4

furnace

opening

confined

space

Figure 1

Outdoor Air

Outlet and inlet air can be brought into the confined space via openings

into a ventilated attic and ventilated crawl space.

furnace

outlet air

inlet air

attic ventilation louvers

crawl space ventilation louvers

Figure 2

Confined Space

Outdoor Air Using Vertical or Horizontal Ducts

If combustion air is taken from outdoors through vertical ducts, the

openings and ducts must have a minimum free area of one square inch

(6.5cm

) per 4,000 Btuh of total appliance input. In installations

drawing combustion air from a ventilated attic both air ducts must

extend above the attic insulation.

furnace

outlet air

inlet air ends one foot above floor

vertical

furnace

inlet air duct

outlet air duct

horizontal

Figure 3

If combustion air is taken from outdoors through horizontal ducts the

openings and ducts must have a minimum free area of one square inch

(6.5cm

) per 2,000 Btuh of total appliance input.

Ventilation and Combustion Air

WARNING: Danger of property damage, bodily injury or death,

this furnace and any other fuel burning appliance must be

provided with enough fresh air for proper combustion and

ventilation of flue gases. Most homes will require that outside air

be supplied. Do not draw air from a corrosive environment such

as a workshop or laundry room.

The requirements for providing air for combustion and ventilation are

listed in the National Fuel Gas Codes NFPA 54/ANSI Z223.1 (in

Canada - CAN/CGA B149).

Note: Air requirements for operation of exhaust fans, kitchen ventilation

systems, clothes dryers, fireplace and any other fuel burning or ventilating

equipment used in the space must be considered in determining

combustion air requirements.

Ventilation Air Openings and Ducts

In determining the free area needed consideration must be given to the

blocking effect of louvers, grills or screens protecting openings.

— If a screen is used to cover openings it must not be smaller than 1/4"

mesh.

— Use the free area of a louver or grill to determine the size opening

required to provide the free area specified. If the free area is not

known assume a 20% free area for wood and a 60% free area for a

metal louver or grill.

— Ducts must have the same cross sectional area as the free area of the

openings to which they connect.

— The minimum dimension of air ducts must not be less than 3 inches.

Installation in an Unconfined Space

An unconfined space is an area including all rooms not separated by

doors with a volume greater than 50 cubic feet per 1,000 Btuh of the

combined total input rates of all appliances which draw combustion air

from that space. For example, a space including a water heater rated at

40,000 Btuh input and a furnace rated at 40,000 Btuh requires a volume

of 4,000 cubic feet (50 x (40 + 40) = 4,000) to be considered as

unconfined. If the space has an 8 ft. ceiling, the floor area of the space

must be 500 sq. ft. In general, particularly in older homes, a furnace

installed in an unconfined space will not require outside air for

combustion. However in a "tight" newly constructed home, outside air

may be necessary to insure adequate combustion.

Installation in a Confined Space

A confined space is an area with volume less than 50 cubic feet per 1,000

Btuh of the combined input rates of all appliances drawing combustion

air from that space. Small areas such as equipment rooms are confined

spaces. Furnaces installed in a confined space which supply heated air

to areas outside the space must draw return air from outside the space

through tightly sealed return air ducts. A confined space must have 2

openings into the space for combustion air. One opening must be within

12 inches of the ceiling and the other must be within 12 inches of the

floor. The required sizing of these openings is determined by whether

inside or outside air is used to support combustion, the method by which

the air is brought to the space (vertical or horizontal duct) and by the total

input rate of all appliances in the space. See Figure 1.

All Air From Inside — Confined Space

If combustion air is taken from the heated space the 2 openings must

each have a free area of at least one square inch per 1,000 Btuh of total

input of all appliances in the confined space but not less than 100 square

inches (645cm

) of free area.

For example: for a 40,000 Btuh furnace only in the confined space each

opening must be 100 square inches (645cm

) each of free area.

WARNING: Combustion air must not be drawn from a heated

space which includes exhaust fans, fireplaces or other devices that

may produce a negative pressure in the space.

12427-2-0903

Page 5

C. 4" (102mm) Oval In-The-Wall (all parts purchase locally)

1. Type B-1 oval pipe or B-W vent pipe

2. Type B-1 oval elbows or B-W oval elbows

3. Single story type B-1 or (B-W) gas vents require a baseplate

and one pair of ceiling plate spacers.

4. Multi-story type B-1 or (B-W) gas vents require a baseplate,

one pair of ceiling plate spacers at the first floor ceiling and

one pair of fire stop spacers at each successive ceiling level.

Stud space around gas vents must be free of obstructions and

building paper.

BRACKET

BASEPLATE

4" B-1 OVAL

BASEPLATE

SPACER

4" B-1 OVAL

4" 45 DEG.

OVAL ELBOWS

SPACER

BASEPLATE

4" B-1 OVAL

VENT

ENCLOSURE

ADAPTER

BASEPLATE

SIDE

FRONT

4" ROUND

WALL

Figure 4

Qualified Installing Agency

Installation and replacement of gas piping, gas utilization equipment or

accessories and repair and servicing of equipment shall be performed

only by a qualified agency. The term "qualified agency" means any

individual, firm, corporation or company which either in person or

through a representative is engaged in and is responsible for (a) the

installation or replacement of gas piping or (b) the connection, installation,

repair or servicing of equipment, who is experienced in such work,

familiar with all precautions required and has complied with all the

requirements of the authority having jurisdiction.

The installation must conform with local codes or, in the absence of local

codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54*

Natural and Propane Installation Code, CSA B149.1.

*Available from the American National Standards Institute, Inc., 11 West 42nd St., New

York, N.Y. 10036.

Clearances

1. In selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper installation.

2. The FAW-40 can be attached to the wall or recessed into the wall up

to 9 1/2 inches (24.1cm) in depth. Note:

Do not place combustible

header or material on top of unit when installed in wall.

Maintain 3/4" minimum spacing above heater.

3. The wall in which the furnace is recessed has (0) zero (0mm)

clearance to the furnace sides.

4. When using side discharge registers, SOR-1 or SOK-1, the furnace

cannot be recessed into the wall.

5. Clearance to sidewall or combustible material is 4 inches (10.2cm).

6. Ceiling clearance is 4 inches (10.2cm).

7. Floor and rear wall clearance is (0) zero inches (0mm).

8. Clearance of 18 inches (46cm) is required to adjacent wall or

combustible material when flush mounted SOR-1, side outlet register

is used.

Before Installing Consider The Following Venting

1. A chimney for residential-type or low-heat gas utilization equipment

shall extend at least 3 feet (914mm) above the highest point where

it passes through a roof of a building and at least 2 feet (610mm)

higher than any portion of building within a horizontal distance of 10

feet (3m).

2. This furnace must not be connected to a chimney flue serving a

separate solid-fuel burning appliance.

3. Uninsulated Single-Wall Metal Pipe shall not be used outdoors

in cold climates for venting gas utilization equipment.

4. Attention! This Fan Type Vented Wall Furnace is equipped with a

vent safety switch. In the event of spillage of flue products due to

improper venting the vent safety switch will open, which results in

the main burners to "shut off".

Model No. FAW-40 may be vented as shown in Figure 4. The vent

cap termination must be at least 12 feet (3.7m) above the floor and

must exhaust to the outdoors.. Clearance to combustible construction

is held by the fixed spacers at 1 inch (25mm) with B-1 or (B-W) vent

pipe. Installation must conform to local codes.

A. 4" (102mm) Round (all parts purchase locally except Item 2)

1. Type B-1 round pipe

2. Part No. DV-648, 4" (102mm) oval-to-round flue adapter kit

(see accessories)

3. Single story type B-1 gas vents require a baseplate and one

pair of ceiling plate spacers.

4. Multi-story type B-1 gas vents require a baseplate, one pair of

ceiling plate spacers at the first floor ceiling and one pair of

fire stop spacers at each successive ceiling level.

B. 4" (102mm) Oval (all parts purchase locally)

1. Type B-1 oval pipe or B-W vent pipe

2. Single story type B-1 or (B-W) gas vents require a baseplate

and one pair of ceiling plate spacers.

3. Multi-story type B-1 or (B-W) gas vents require a baseplate,

one pair of ceiling plate spacers at the first floor ceiling and

one pair of fire stop spacers at each successive ceiling level.

12427-2-0903

Page 6

12427-2-0903

Page 7

8. Align clearance holes on 6" x 10" (152mm x 254mm) duct with

screw holes on inner casing back and mark duct to be 2 1/4" (57mm)

shorter than 8" x 12" (203mm x 305mm) boot. Remove duct and cut

to proper length.

9. Attach 6" x 10" (152mm x 254mm) duct to inner casing back with (4)

#8 x 3/8" (9mm)screws removed in Step 3, 2 on top and 2 on bottom.

10. Insert rear register into 8" x 12" (203mm x 305mm) boot. Attach

rear register to wall with (2) #10 x 1"(25mm) screws provided.

11. Installation of ROK-1 is completed.

Locating Furnace On Wall

The furnace is to be located on a wall. The furnace is 14 1/8" (35.9cm)

in width and can be recessed into the wall with typical stud spacing.

A template is provided in furnace carton for locating gas line connection.

Also, refer to Figure 7 for positioning the furnace on wall and for

locating gas line connection.

Locating Gas Supply

The gas line can enter the furnace either through the floor or wall. The

gas line opening should be made at this time. Location of the opening

will be determined by the position of floor joists and the valve and union

used for servicing. See Figure 7.

72 3/4"

14 3/8"

CUT OUT OPENING FOR RECESSED MOUNTING

RECESSED MOUNTING

LOCATION

2 1/8"

GAS LINE

HOLE 1 1/4"

ELECTRICAL WIRING HOLE

GAS LINE/ELECTRICAL OPENINGS FOR

RECESSED AND SURFACE MOUNT

Figure 7

Locating Electric Supply

A 7/8" (22mm) diameter knockout is provided at the bottom of the left

and right side panels. A three-prong (grounding) plug assembly is

located within the control compartment (bottom) of the furnace. Please

remove 7/8" (22mm) knockout from appropriate side panel when

routing plug assembly to an electrical outlet.

Installation of Three-prong (Grounding) Plug Assembly

1. Disconnect nylon cap on 3' (914mm) plug assembly from nylon plug

on wiring harness. Remove 3' (914mm) plug assembly from control

compartment (bottom) of the furnace.

2. Remove 7/8" (22mm) knockout from appropriate side panel.

3. Insert nylon cap on 3' (914mm) plug assembly into the 7/8" (22mm)

hole in the side panel.

4. Connect nylon cap on 3' (914mm) plug assembly to nylon plug on the

wiring harness.

5. Place 7/8" (22mm) strain relief bushing around the cord of the 3'

(914mm) plug assembly. Insert 7/8" (22mm) strain relief bushing

into the 7/8" (22mm) hole in the side panel.

Attention! The 7/8" (22mm) strain relief bushing is located within the

same yellow envelope as the Installation Instructions and Owner's

Manual.

Attaching Furnace to Wall

When attaching furnace to the wall remove that portion of baseboard and

molding on the wall which is behind the furnace. Attach furnace to wall,

at the outer casing top, with (2) toggle bolts provided and to floor, at the

outer casing bottom, with (2) #10 x 1 1/2" (38mm) screws provided.

Gas Supply

Check all local codes for requirements, especially for the size and type

of gas supply line required. On Natural gas lines less than 75' (22.9m)

long, use 1/2" (13mm) pipe; on longer runs, use 3/4" (19mm) iron pipe

or equal. On LP gas lines please consult LP gas supplier.

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.

A manual main gas cock should be located in the vicinity of the unit.

Where none exists, or where its size or location is not adequate, contact

your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant to the

action of liquefied petroleum gases. The gas lines must be checked for

leaks by the installer. This should be done with a soap solution watching

for bubbles on all exposed connections, and if unexposed, a pressure test

should be made.

Never use an exposed flame to check for leaks. Appliance must be

disconnected from piping at inlet of control valve and pipe capped

or plugged for pressure test. Never pressure test with appliance

connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas line

upstream of the gas control to aid in servicing. It is required by the

National Fuel Gas Code that a drip line be installed near the gas inlet.

This should consist of a vertical length of pipe tee connected into the gas

line that is capped on the bottom in which condensation and foreign

particles may collect.

Figure 8

Method of Installing a Tee Fitting Sediment Trap

The use of the following gas connectors is recommended:

— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors of Other

Than All-Metal Construction

The above connectors may be used if acceptable by the authority having

jurisdiction.

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.

plugged tapping, accessible for test gauge connection, must be

placed immediately upstream of the gas supply connection to the

appliance.

2. The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of that

system at test pressures in excess of 1/2 psig (3.5 kPa).

3. The appliance must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to or

less than 1/2 psig (3.5 kPa).

12427-2-0903

Page 8

Attention! If one of the above procedures results in pressures in excess

of 1/2 psig (14" w.c.) (3.5 kPa) on the appliance gas valve, it will result

in a hazardous condition.

Checking Manifold Pressure

Both Propane and Natural gas valves have a built-in pressure regulator

in the gas valve. Natural gas models will have a manifold pressure of

approximately 4.0" w.c. (.996kPa) at the valve outlet with the inlet

pressure to the valve from a minimum of 5.0" w.c. (1.24kPa) for the

purpose of input adjustment to a maximum of 10.5" w.c. (2.615kPa).

Propane gas models will have a manifold pressure approximately 10.0"

w.c. (2.49kPa) at the valve outlet with the inlet pressure to the valve from

a minimum of 11.0" w.c. (2.739kPa) for the purpose of input adjustment

to a maximum of 13.0" w.c. (3.237kPa).

A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge

connection, is located on the outlet side of the gas control.

The built-in regulator comes on at approximately 1/4th pressure and full

on in 10 seconds.

Figure 9

High Altitudes

For altitudes/elevations above 2,000 feet (610m), input ratings should

be reduced at the rate of 4 percent for each 1,000 feet (305m) above sea

level. For Canadian high altitude applications, this appliance is suitable

for installation at elevations between 0 feet (0m) and 4,500 feet (1,372m)

without change.

Piezo Pilot Ignitor Instructions

Depressing the red button completely causes a spark to occur at the pilot.

This is a substitute for a match which requires opening the pilot hole

cover.

To light the pilot, it is important that the electrode be 1/8" (3mm) from

the thermocouple. The spark must occur at the point the burner flame

hits the thermocouple. The end of the electrode will be red hot with the

pilot on.

On a new installation with air in the gas line, it is suggested that a match

be used. The match will light the pilot faster than the piezo under this

condition.

Proper Pilot Flame

The correct pilot flame (Figure 10) will be blue, extending past the

thermocouple. The flame will surround the thermocouple just below the

tip.

Natural gas pilots require adjusting when the inlet gas pressure is above

5" w.c. (1.245kPa). Remove the pilot cover screw on the control valve

(Figure 9), and turn the adjustment screw clockwise to reduce flame.

Replace pilot cover screw to eliminate gas leakage.

LP gas (propane) will not require adjustment.

After use, cleaning may be required for the proper flame.

Proper Main Burner Flame

The correct flame will be a short, blue inner flame with a much larger,

light blue, outer flame. The burner does not have a primary air adjustment.

The flame will be correct if the factory-set pressure and orifice opening

are used. After the furnace has been operating, the burner ports may be

blocked by foreign matter carried in by combustion air. Therefore,

cleaning of the burner may be needed for proper flame.

To clean burner port disconnect the gas supply to the valve, and remove

the screws fastening the burner door. After removing the burner door

from the burner box, remove each main burner. Pilot mounting bracket

will need to be unscrewed and moved out of the way to remove all

burners. Burners can be blown out using compressed air or by blowing

through them. Be sure there is no lint or foreign debris blocking the

burner ports. Reassemble using the same screws earlier removed and

locate pilot in the same position as before and noted above.

SPARK

ELECTRODE

THERMOCOUPLE

PILOT

BURNER

STANDING PILOT

PILOT LOCATION END VIEW

PILOT SHIELD

THERMOCOUPLE

SPARK

ELECTRODE

STANDING PILOT SHOWN

BURNER

PILOT

HOT SURFACE

IGNITOR

FLAME

ROD

GROUND

ELECTRODE

3/8" TO 1/2"

PILOT FLAME

IP-MODEL PILOT

Figure 10

Figure 11

Cleaning Combustion (Exchanger) Assembly

A QUALIFIED SERVICE PERSON should remove the combustion

(exchanger) assembly and flue baffles. Apply air pressure to the inside

of the combustion (exchanger) assembly and flue baffles in order to

clear all passageways.

12427-2-0903

Page 9

Oiling the Motor

The fan motor should be cleaned and oiled once each heating season. Oil

holes are located on the top at each end of the motor. Use a few drops of

#10 motor oil. To clean the motor, blow air through its ventilation

openings with a vacuum cleaner or low pressure air source.

Wiring

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code,

CSA C22.1, if an external electrical source is utilized. This appliance

is equipped with a three-prong [grounding] plug for your protection

against shock hazard and should be plugged directly into a properly

grounded three-prong receptacle. Do not cut or remove the

grounding prong from this plug. For an ungrounded receptacle, an

adapter, which has two prongs and a wire for grounding, can be

purchased, plugged into the ungrounded receptacle and its wire connected

to the receptacle mounting screw. With this wire completing the ground,

the appliance cord plug can be plugged into the adapter and be electrically

grounded. A 7/8" (22mm) hole is provided in the junction box for use

with a conduit connector if local codes require this type of protection.

Thermostat Installation

The thermostat should be installed in the same room as the furnace 4'

(1.2m) to 5' (1.5m) above the floor and away from another heat source

(cooking stove, hot water heater, etc.) including walls and doorways

with a heat source in an adjoining room. Do Not Install Thermostat on

Outside Wall.

Insulated Vent Enclosure

Vented wall furnaces installed in buildings with flat roofs can have poor

venting. The cold vent pipe will have a delay in proper venting and cause

the wall furnace to shut "OFF" by the vent safety switch. To prevent

delayed venting as well as condensation of flue products an insulated

vent enclosure is recommended.

Use type B vent pipe and maintain at least a one inch (25mm) clearance

to combustibles.

Use metal thimble to protect vent pipe as it passes through combustibles.

Figure 12

Vent Safety Shutoff System

This appliance must be properly connected to a venting system. This

appliance is equipped with a vent safety shutoff system.

Warning: Operation of this wall furnace when not connected to

a properly installed and maintained venting system or tampering

with the vent safety shutoff system can result in carbon monoxide

(CO) poisoning and possible death.

This furnace is equipped with a manual reset vent safety switch. The

manual reset vent safety switch will cause gas flow to the main burners

to "shut off" due to improper venting or a blocked flue.

To reset the manual reset vent safety switch:

1. Remove front panel.

2. Depress manual reset button. The manual reset vent safety switch is

located on the draft diverter.

3. Replace front panel.

If the manual reset vent safety switch continues to "shut off" the gas flow

to the main burners a qualified service person must be contacted to

inspect for improper venting, blockage in the vent pipe or the manual

reset vent safety switch for being defective.

Figure 13

BURNER BOX

GAS VALVE

JUNCTION BOX-

TRANSFORMER

LIMIT SWITCH

FAN SWITCH

VENT LIMIT SWITCH

FLUE CONNECTOR

FAN

PIEZO

IGNITOR

DRAFT DIVERTER

Figure 14

FAN SWITCH

LIMIT SWITCH

12427-2-0903

Page 10

SERVICE AND MAINTENANCE SUGGESTIONS

CALL SERVICEMAN

GENERAL: All furnaces have been fire-tested to check for proper

operation. This includes, main burner flame, pilot flame, fan operation,

fan control, limit control and automatic valve operation. If the furnace

fails to function on initial installation, it is advisable to re-check the

following:

1. 115 volts to the junction box.

2. Inlet gas pressure.

3. The 24 volt system.

4. Type of gas being used and that shown on the rating label.

The Service Department at Empire Comfort Systems, Inc. may be

contacted to assist in servicing furnace.

Standing Pilot Model

Servicing the Pilot and Main Burners, Pilot Orifice, Thermocouple,

and Main Burner Orifices: Disconnect the gas supply at the inlet to the

control valve. Then remove the burner door to gain access to the above

listed components.

Spark Igniter Does Not Light Pilot: With air in the gas line, such as

when the furnace is first installed or was off all summer, the pilot flame

may be too lean to ignite on the first few trials. Turn the control valve

knob to pilot position and depress the red reset button. Holding the

button down continually to bleed the line;.

1. Use lighter rod to light pilot with a match.

2. Use the piezo ignitor at 30 second intervals until it lights.

If Electrode Does Not Produce Spark:

1. Check wire connections.

2. Check gap for pilot burner to the electrode tip. Should be between

1/8" (3mm) and 3/16" (5mm). Electrode wire and tip must be more

than 1/4" (6mm) away from all other metal components.

If Pilot Does Not Light By Any Means:

1. Check valve knob for being in the "Pilot" position.

2. Check pilot adjustment for being full open (counterclockwise to

open).

3. If gas is available in the supply tubing, the pilot orifice and/or pilot

burner is probably restricted by a spider web. Clean pilot assembly

and relight.

If Pilot Does Not Remain On After Releasing Knob:

1. Follow instructions and hold button down longer and harder.

2. Determine if pilot flame extends past thermocouple; if not, adjust

input or clean pilot burner.

3. Replace thermocouple if millivolts read less than 15 millivolts.

Main Gas Valve Does Not Open When Thermostat Is Turned To On:

1. Check for 24 volts to valve by removing one wire and touching to

the SAME TERMINAL it was on. Terminal should have a light

spark. DO NOT SHORT ACROSS TERMINALS, AS IT WILL

BURN OUT THE WALL THERMOSTAT.

2. Thermostat wires at the wall may be shorted, so check for a faulty

thermostat.

3. To check for line voltage to furnace, remove front panel and short

across two-terminal fan control to allow fan to operate (Figure 14).

CAUTION: Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

IP-Model Pilot

This heater is using a Honeywell "Smart Valve" system for intermittent

pilot ignition.

On a call for heat by the thermostat this control turns on a 24 volt mini

hot surface ignitor which lights a pilot that in turn lights the main burner.

The gas valve used in this system is a step opening which opens at a

lower pressure for ignition and then steps to a full inlet pressure of 4"

O pressure on Natural gas and 10" H

0 pressure on LP gas.

Pilot Flame Adjustment

The pilot flame should envelop 3/8 to 1/2 inch (10 to 13mm) of the tip

of the flame rod. See Figure 10.

To adjust:

1. Remove the pilot adjustment cover screw.

2. Turn the inner adjustment screw clockwise

to decrease

or counterclockwise

to increase pilot flame. Pilot adjust-

ment is shipped at full flow rate. Turn the inner adjustment screw

clockwise

if the inlet pressure is too high.

3. Replace the cover screw after the adjustment to prevent gas

leakage.

OFF

IGNITOR

CONTROL

INLET PRESSURE TAP

OUTLET PRESSURE TAP

PILOT ADJUSTMENT-

UNDER CAP SCREW

PILOT OUTLET

PRESSURE REGULATOR

ADJUSTMENT-UNDER CAP

SCREW

GAS FLOW

IGNITOR

CONTROL

TO 24 V. THERMOSTAT

TO 24 V. COMMON ON TRANSFORMER

TO 24 V."HOT" ON TRANSFORMER

WIRING

I P-MODEL GAS VALVE AND WIRING

IGNITOR-PILOT ASSY.

FAN

SWITCH

MOTOR

HONEYWELL IP

SMART VALVE

120 VAC

LIMIT

CONTROL

VENT SAFETY

LIMIT

THERMOSTAT

40 VA TRANSFORMER

24 VAC

120VAC

VALVE CONTROL

CONNECTOR

L1 "HOT"

L2 NEUTRAL

LADDER WIRING DIAGRAM-IP VALVE

Figure 15

12427-2-0903

Page 11

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by

hand. When lighting the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING smell all around the appliance

area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neigh-

bor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in

or turn by hand, don't try to repair it; call a

qualified service technician. Force or attempted

repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualified service techni-

cian to inspect the appliance and to replace any part

of the control system and any gas control which has

been under water.

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to appliance if service is

to be performed .

3. Remove control access panel (lower front panel).

4. Push in gas control knob slightly and turn clock-

wise to "OFF." Do not force.

5. Replace control access panel (lower front panel).

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. Remove control access panel (lower front panel).

5. Turn gas control knob clockwise to "OFF."

6. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the floor. If you smell gas,

STOP! Follow "B" in the safety information above. If

you don't smell gas, go to the next step.

7. Remove the pilot access cover located on the combus-

tion chamber.

8. Find pilot - follow metal tube

from gas control. The pilot is

located between the two burner

tubes behind the pilot access cover.

9. Turn gas control knob counterclockwise

to "PILOT."

10. Push and hold red reset button down completely and

repeatedly push the ignitor button until the pilot burner

is lit. Pilot may also be lit with a match. Continue to

hold the red reset button down for about one (1)

minute after the pilot is lit. Release button and it will

pop back up. Pilot should remain lit. If it goes out,

repeat steps 5 through 10.

• If button does not pop up when released, stop and

immediately call a qualified service technician or

gas supplier.

• If the pilot will not stay lit after several tries, turn

the gas control knob to "OFF" and call your

service technician or gas supplier.

11. Replace pilot access cover.

12. Turn gas control knob counterclockwise

to "ON."

13. Replace control access panel (lower front panel).

14. Turn on all electric power to the appliance.

15. Set thermostat to desired setting.

STANDING PILOT MODEL

12427-2-0903

Page 12

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance is equipped with an ignition device

which automatically lights the pilot.

Do not try to light the pilot by hand.

B. BEFORE OPERATING smell all around the appliance

area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neigh-

bor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire

department.

C. Use only your hand to slide the gas control knob.

Never use tools. Force or attempted repair may

result in a fire or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualified service techni-

cian to inspect the appliance and to replace any part

of the control system and any gas control which has

been under water.

1. STOP! Read the safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition device

which automatically lights the pilot. Do not try to

light the pilot by hand.

OFF

IGNITOR

CONTROL

GAS FLOW

GAS VALVE SHOWN IN OFF POSITION

HONEYWELL IP SMART VALVE

5. Remove front panel door.

6. Slide gas control switch to "OFF."

7. Wait ten (10) minutes to clear out any gas. Then

smell for gas, including near the floor. If you smell

gas, STOP! Follow "B" in the safety information

above. If you don't smell gas, go to the next step.

8. Slide gas control switch to "ON".

9. Replace front panel door.

10. Turn on all electric power to the appliance.

11. Set thermostat to desired setting.

12. If the appliance will not operate, follow the instruc-

tions "TO TURN OFF GAS TO APPLIANCE" and

call your service technician or gas supplier.

OPERATING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to the appliance if service

is to be performed.

3. Remove front panel door.

4. Slide gas control switch to "OFF."

5. Replace front panel door.

INTERMITTENT PILOT (IP) MODEL

12427-2-0903

Page 13

START

System Check

END

SEQUENCE OF OPERATION

Trial for

Ignition

Main Burner

Operation

Apply 24 VAC

to Appliance

Thermostat

Calls for Heat

Flame Signal

Detected

Internal Check

• Pilot Valve Opens

• Ignitor Powered

Pilot Light and Flame is

Sensed During Trial

For Ignition (1)

• Ignitor OFF

• Main Valve Opens

Flame Signal

Lost?

Thermostat Call

for Heat Ends

5 Minute Retry

Delay

3 Second Flame

Failure Recycle

Delay

YES

• Pilot Valve Ignition OFF

• Wait for Flame Signal to

Disappear

(1) Ignitor will turn OFF about 30 seconds into the trial for ignition if the pilot flame has not lit. It will turn back ON for the final 30 seeonds

of the 90 second trial for ignition. The pilot valve will be energized during the entire trial for ignition. This is normal operation for this gas

ignition system.

• Pilot Valve Closes

• Ignition OFF

Main Pilot Valves

Flame Lost More

Than 5 Times in

One Call for Heat

Main Pilot

Valves Close

YES

12427-2-0903

Page 14

SmartValve™ System Troubleshooting Sequence

Note: Before Troubleshooting, Become Familiar

with the Sequence of Operation

IP SYSTEM TROUBLESHOOTING SEQUENCE

YES

• Turn OFF Gas Supply

• Disconnect System Control

Harness

• Set Thermostat to Call for

Heat

Plug Harness into SmartValve

Control

Wait for Internal Check Delay

(SV9501)

Igniter Warms UP and

Glows Red

System is Okay

Main Valve Opens and

Main Burner Lights

• Turn On Gas Supply

• Pilot Burner Lights

Check for Proper Voltage at

Control Harness (See Inset A

-Voltage Should be 24V

Between Thermostat and

24V Common, and 24V

Between 24V Common and

24V Hot.)

Reconnect Pilot Burner Cable

• Check that Pilot Gas is Flowing

Wait to Assure Pilot Gas Tubing

is Purged.

Replace Igniter/Flame Rod Assembly

Note: Igniter Will Cycle OFF

and Back ON Once During

the 90 Second Ignition Trial

Cycle Thermostat OFF and Back ON

Main Burner Lights

Replace SmartValve Control

Check Transformer and Line

Volt Supply

• Check that Pilot Flame Makes Good

Contact with Pilot Burner Flame

Rod

• Check for Good Electrical

Connection Through the Pilot

Tubing

• If Both of the Above are Good,

Replace Igniter/Flame Rod

• Measure Voltage Between 24V Hot

and 24V Common Leads to

SmartValve Control. Must Measure

at Least 19.5 VAC with Igniter

Powered. See Inset A to Identify

Proper Lead. This Check Must be

Done with the SmartValve Control

Connected and Igniter Powered.

Unplug Pilot Burner Cable.

Measure Voltage at SmartValue

HSI Element Output (See Inset B)

24V Nominal

YES

CHECK

• Line Voltage Power

• Low Voltage Transformer

• Limit Controller

• Thermostat

• Wiring

Replace SmartValve Control

START

Replace Igniter/Flame Rod Assembly

Reconnect Pilot Burner Cable

INSET A

24Volt

Thermostat

Volts

24 Volt

Common

Volts

24 Volt

Hot

EFT

Output

End View

of Control

Harness

Connector

INSET B

HSI

Terminals

12427-2-0903

Page 15

INDEX PART

NO. NUMBER DESCRIPTION

INDEX PART

NO. NUMBER DESCRIPTION

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

1 WFA-115 GASKET - HEADER

2 DV-1247 TOP PLATE (USA)

2 15668 TOP PLATE (CANADA)

3 R-3165 DOOR CLIP (2 REQUIRED)

4 DV-1204 CASING SIDE - RIGHT

5 DV-1203 CASING BACK

6 DV-1205 CASING SIDE - LEFT

7 DV-1248 AIR DROP (INCLUDES NO. 54)

8 DV-1231 TURBULATOR (3 REQUIRED)

9 DV-1250 DIVIDER PLATE

10 DV-1234 OUTLET BOX

11 DV-1225 OUTLET BOX COVER

12 R-3177 VENT SAFETY SWITCH

13 R-3161 FAN BLADE

14 R-3166 FAN MOTOR

15 DV-1246 MOTOR MOUNTING BRACKET

16 8720130 BUSHING (5 REQUIRED)

17 8520141 RUBBER GROMMET

(4 REQUIRED)

18 8520142 BRASS BUSHING

(4 REQUIRED)

19 R-3164 DOOR CLIP (2 REQUIRED)

20 DV-1251 INNER SHIELD - RIGHT

(INCLUDES NO. 23)

21 R-6176 FAN CONTROL SWITCH

22 R-3176 LIMIT SWITCH

23 DV-1253 INNER SHIELD COVER PLATE

(2 REQUIRED)

24 DV-1254 INNER SHIELD FRONT (USA)

24 15669 INNER SHIELD FRONT

(CANADA)

25 R-3163 FILTER RETAINER

26 R-3162 FILTER

27 DV-1252 INNER SHIELD -LEFT

(INCLUDES NO. 23)

28 DV-1256 EXCHANGER ASSEMBLY

29 DV-1235 PILOT BRACKET (IP ONLY)

30 R-3232 PILOT - NAT (IP ONLY)

30 R-3233 PILOT - LPG (IP ONLY)

31 742121 ORIFICE - NAT (3 REQUIRED)

31 P-88-60 ORIFICE - LPG (3 REQUIRED)

32 DV-1236 MANIFOLD

33 DV-1258 FRONT PANEL

34 722040 MANIFOLD UNION

35 852051 BUSHING 3/8 x 1/2

36 R-5655 GAS VALVE - LPG (SPP ONLY)

36 R-2148 GAS VALVE - NAT (SPP ONLY)

36 R-3170 GAS VALVE - NAT (IP ONLY)

36 R-3171 GAS VALVE - LPG (IP ONLY)

37 R-2708 PIEZO IGNITOR (SPP ONLY)

38 FF-160 PIEZO BRACKET (SPP ONLY)

39 DV-1318 OBSERVATION HOLE COVER

PLATE

40 DV-1242 BURNER COMPARTMENT FRONT

(SPP ONLY)

41 DV-1237 BURNER COMPARTMENT BODY

42 712045 MANIFOLD GASKET

43 GWT-168 AIR SHUTTER FRONT

(LPG ONLY)

44 GWT-169 AIR SHUTTER REAR

(LPG ONLY)

45 R-3031 BURNER (3 REQUIRED)

46 DV-1239 BURNER BRACKET

47 UH-452 TRANSFORMER MOUNTING

BRACKET (IP ONLY)

47 UH-810 TRANSFORMER MOUNTING

BRACKET (SPP ONLY)

48 R-1995 TRANSFORMER (SPP ONLY)

48 8720100 TRANSFORMER (IP ONLY)

49 UH-451 JUNCTION BOX COVER

50 DV-572 JUNCTION BOX

51 DV-1260 COVER PLATE - AIR DROP

52 872056 BUSHING

53 872053 CORD SET

54 8720148 BUSHING

55 DV-1215 BOTTOM PLATE

56 R-3034 PILOT - NAT (SPP ONLY)

56 R-3035 PILOT - LPG (SPP ONLY)

57 GWT-021 PILOT BRACKET (SPP ONLY)

58 R-3180 ELECTRODE AND WIRE

(SPP ONLY)

59 R-2256 THERMOCOUPLE -18"

(SPP ONLY)

60 R-6389 WALL THERMOSTAT - 24 VOLT

NOT SHOWN DV-1261 PILOT TUBING

NOT SHOWN 742158 PILOT ORIFICE - NAT (SPP ONLY)

NOT SHOWN 742266 PILOT ORIFICE - LPG (SPP ONLY)

NOT SHOWN 742154 PILOT ORIFICE - NAT (IP ONLY)

NOT SHOWN R-3265 PILOT ORIFICE - LPG (IP ONLY)

NOT SHOWN R-3172 WIRE HARNESS (SPP ONLY)

NOT SHOWN R-3173 WIRE HARNESS (IP ONLY)

NOT SHOWN R-1587C VENT SAFETY WIRE ASSEMBLY

How To Order Repair Parts...

Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor.

Parts can be shipped directly to the service person/dealer.

All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment. Then

determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give

all this information . . .

Furnace Model Number Part Description

Furnace Serial Number Part Number

Type of Gas (Propane or Natural)

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.

Shipments contingent upon strikes, fires and all causes beyond our control.

Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529

USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

12427-2-0903

Page 16

12427-2-0903

Page 17

Service Notes

12427-2-0903

Page 18

Empire Comfort Systems, Inc.

Nine Eighteen Freeburg Ave.

Belleville, Illinois 62220-2623

PH: 1-618-233-7420

PH: 1-800-851-3153

FAX: 1-618-233-7097

FAX: 1-800-443-8648

E-MAIL: info@empirecomfort.com

WEB SITE: www.empirecomfort.com

12427(F)-2-0903

Page 1

INSTRUCTIONS POUR L’INSTALLATION

MANUEL DU PROPRIÉTAIRE

RADIATEUR MURAL À

CIRCULATION FORCÉE ET

AVEC ÉVACUATION

MODÈLE

FAW-40-1SPP

FAW-40-1IP

DATE D’ENTRÉE EN VIGUEUR

SEPTEMBRE 2003

AVERTISSEMENT:

Si les informations dans ce manuel ne sont pas

exactement suivies, un feu ou une explosion

peut en résulter causant des dommages à la

propriété, des blessures corporelles ou la mort.

— Ne pas entreposer ou employer de la gazoline ou

d’autres vapeurs ou liquides inflammables

àproximité de cet appareil ou tout autre appareil.

— QUE FAIRE SI VOUS SENTEZ LE GAZ.

• N’essayer pas d’allumer un appareil.

• Ne toucher pas un interrupteur électrique;

n’employer pas un téléphone dans le bâtiment.

• Appeler immédiatement votre fournisseur de

gaz en employant le téléphone de votre voisin.

Suivre les instructions du fournisseur de gaz.

• Si vous ne pouvez pas contacter votre

fournisseur de gaz, appeler le poste de

pompiers.

— L’installation et le service doivent être exécutés

par un installateur qualifié, une agence d’entretien

ou un fournisseur de gaz.

AVERTISSEMENT:

Si l’installation, l’usage et l’entretien de ce

produit ne sont pas faits selon les instructions

du fabricant, ce produit peut vous exposer à

des matières contenues dans le carburant ou

provenant de la combustion du carburant

lesquelles peuvent causer la mort ou de

sérieuses maladies.

Installateur: S'il vous plaît, laissez ces instructions

avec le consommateur.

Consommateur: Garder ces instructions pour

référence ultérieure.

12427(F)-2-0903

Page 2

Introduction

Toujours consulter le département de construction de votre région en ce

qui regarde les règlements, les codes ou les ordonnances qui s’appliquent

à l’installation d’un radiateur mural avec évacuation.

Instructions pour l'Installateur

1. Après l’installation, l’installateur doit laisser le manuel d’instructions

au propriétaire.

2. L’installateur doit demander au propriétaire de compléter et poster

la carte de guarantie de l’unité de chauffage.

3. L’installateur doit expliquer au propriétaire la mise en marche et le

fonctionnement du radiateur et du thermostat.

AVERTISSEMENT:

Tout changement fait à ce radiateur ou à ces commandes peut

être dangereux. Ceci est un appareil de chauffage et si un

panneau, une porte ou un dispositif protecteur est enlevé pour

l’entretien de cet appareil, il doit être replacé avant de remettre

en marche.

Informations Générales

Cette série est un modèle conformément certifié avec l'American Na-

tional Standard / CSA Standard Z21.86 et CSA 2.32 par Canadian

Standards Association comme étant un radiateur mural à circulation

forcée et avec évacuation, devant être installé selon ces instructions.

Tout changement du modèle d’origine, installé autrement que

décrit dans ces instructions ou fonctionnant avec un genre de gaz qui

n’est pas indiqué sur la plaque d’identification, est la responsabilité

de la personne et de la compagnie faisant ce changement.

Important

Toute la correspondance doit mentionner le numéro complet du modèle

et de la série et le genre de gaz.

AVIS: Pendant le premier allumage de cette unité, la peinture cuira et

de la fumée se produira. Pour prévenir les détecteurs de fumée de se

déclencher, bien ventiler l’appartement dans lequel l’unité est installée.

Installation sur un Tapis ou Tuile

Si cet appareil est installé directement sur un tapis, tuiles ou tout genre

de matériel combustible autre qu’un plancher de bois, cet appareil doit

être installé sur un panneau de métal ou de bois, celui-ci ayant la largeur

et la profondeur de l’appareil.

La base que nous décrivons ci-dessus ne signifie pas le genre de base

contre le feu comme il est utilisé pour les poêles à bois. La protection

est pour les tapis extrêmement épais et les tuiles de couleur qui pourraient

se décolorer.

Installation dans les Garages Residentiels

Tous les équipements dans les garages résidentiels employant du gaz,

doivent être installés de façon à ce que les brûleurs et les appareils pour

allumer les brûleurs doivent être situés à au moins 18" (45.7cm) au

dessus du plancher.

Tous ces équipements doivent être situés ou protégés de façon à ce qu’un

véhicule en se déplaçant ne puisse les endommager.

SPÉCIFICATIONS

Modèle FAW-40SPP FAW-40IP

Puissance d’entrée BTUH(KW/H) 40,000 (11.7) 40,000 (11.7)

Hauteur 72 1/2" (184.2cm) 72 1/2" (184.2cm)

Largeur 14 1/8" (35.9m) 14 1/8" (35.9m)

Profondeur 10 3/8" (26.4mm) 10 3/8" (26.4mm)

Arrivée de gaz(tuyau) 1/2" (1.27cm) 1/2" (1.27cm)

Collet de l’évent ovale de type B 4" (10.2cm) 4" (10.2cm)

CFM 275 275

ACCESSOIRES

Registre, sortie de côté, registre fixe SOR-1

Sortie de côté, extension maximum de 10" SOK-1

(254mm), registre fixe

Sortie arrière, extension maximum de 10" ROK-1

(254mm), registre ajustable.

Enceinte de l’évent, 24" (61cm) [pour une FVE-24

chambre jusqu’à 96 1/2" (245cm) de hauteur]

Enceinte de l’évent, 34" (86cm) [pour une FVE-34

chambre jusqu’à 106 1/2" (270.5cm) de hauteur]

Enceinte de l’évent, 46" (117cm) [pour une FVE-46

chambre jusqu’à 118 1/2" (301cm) de hauteur]

Assemblage de l’adaptateur de la bouche DV-648

ovale à rond de 4" (102mm)

CECI EST UN APPAREIL DE CHAUFFAGE

NE PAS FAIRE FONCTIONNER CET APPAREIL SANS QUE LE PANNEAU DU DEVANT SOIT INSTALLÉ.

• A cause des hautes températures, cet appareil doit être situé

dans un endroit non achalandé et loin des meubles et des

rideaux.

• Les enfants et les adultes doivent être avisés des dangers des

parois très chaudes et doivent rester loin pour éviter les brûlures

ou l’allumage des vêtements.

• Les petits enfants doivent être surveillés étroitement lorsqu’ils

sont dans le même appartement que l’appareil.

• Les vêtements ou d’autres matériaux inflammables ne doivent

pas être placés sur ou près de l’appareil.

• Tout écran de sûreté qui est enlevé lors de la réparation d’un

appareil, doit être replacé avant de remettre en marche cet

appareil.

• Garder propre le brûleur et le compartiment de contrôle.

• L’installation et la réparation doivent être faites par une

PERSONNE QUALIFIÉE. L’appareil doit être inspecté avant

l’usage et au moins une fois par année, par une personne

qualifiée. S’il y a un excès de poussière venant du tapis, de la

litterie, etc..., de fréquents nettoyages seront requis. Il est

impératif que les compartiments de commandes, les brûleurs et

les passages de circulation d’air de l’appareil soient gardés

propres.

• Ne rien mettre autour du radiateur qui pourrait obstruer le

débit de combustion et la ventilation d’air.

• Les matériaux combustibles, la gazoline ou les vapeurs et

liquides inflammables ne doivent jamais être dans le même

endroit que le radiateur.

• Examiner périodiquement le système de ventilation et remplacer

les pièces défectueuses.

• Faire périodiquement une inspection visuelle de la veilleuse et

des brûleurs. Nettoyer et remplacer les pièces défectueuses.

AVERTISSEMENT: Le couvercle pour l’accès à la veilleuse

doit toujours être gardé hermétiquement fermé lors du

fonctionnement.

• Ne pas utiliser ce radiateur s’il y a une pièce qui a été en contact

avec l’eau. Appeler immédiatement un technicien qualifié pour

inspecter le radiateur et remplacer toute pièce du système de

commande et les commandes de gaz qui ont été en contact avec

l’eau.

• Ce radiateur ne doit pas être branché à une cheminée servant

à un autre appareil brûlant un combustible solide.

IMPORTANT: Ce radiateur a un filtre permanent que

vous pouvez laver au moins une fois par année avant la

saison du chauffage. Pour des endroits souillés ou très

achalandés, des nettoyages plus fréquents seront requis.

La page charge ...

Empire Comfort Systems Furnace FAW-40-1SPP Manuel utilisateur

Marque: Empire Comfort Systems

Modèle: Furnace FAW-40-1SPP

Catégorie: Cheminées

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Empire Comfort Systems Furnace FAW-40-1SPP User manual

Documents connexes

Empire Comfort Systems RH-65-6 Le manuel du propriétaire

Empire Comfort Systems Furnace FAW-40-1SPP Manuel utilisateur

Ce manuel convient également à

Empire Comfort Systems Furnace FAW-40-1SPP Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents