Empire Heating Systems Vented Counterflow Wall Furnace (FAW40) Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: Vented Counterflow Wall Furnace (FAW40)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

FAW40

FAN TYPE VENTED

WALL FURNACE MODELS:

FAW40IPXLP-1 FAW40SPPXLP-1

FAW40IPXNAT-1

FAW40SPPXNAT-1

WARNING

If not installed, operated and maintained

in accordance with the manufacturer's

instructions, this product could expose you

to substances in fuel or from fuel combustion

which can cause death or serious illness.

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions is

not followed exactly, a re or explosion may

result causing property damage, personal

injury or loss of life.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas

supplier, call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

Page 1

37134-6-0520Page 2

INTRODUCTION

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of a vented wall

furnace.

INSTRUCTIONS TO INSTALLER

1. Installer must leave instruction manual with owner after

installation.

2. Installermusthaveownerlloutandmailwarrantycardsupplied

with furnace.

3. Installer should show owner how to start and operate furnace.

WARNING

Any change to this furnace or its control can be dangerous.

This is a heating appliance and any panel, door or guard

removed for servicing an appliance must be replaced prior

to operating the appliance.

To Conserve Gas: Turn off pilot when heater is not in use.

GENERAL INFORMATION

ThisseriesisdesigncertiedinaccordancewithAmericanNational

Standard / CSA Standard Z21.86 and CSA 2.32 by the Canadian

Standards Association, as a Fan Type Vented Wall Furnace and

must be installed according to these instructions.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not

shown on the rating plate is the responsibility of the person

and company making the change.

IMPORTANT

AllcorrespondenceshouldrefertocompleteModelNo.,SerialNo.

and type of gas.

NOTICE:Duringinitialringofthisunit,itspaintwillbakeoutand

smokewilloccur.Topreventtriggeringofsmokealarms,ventilate

the room in which the unit is installed.

INSTALLATION ON RUGS AND TILE

If this appliance is installed directly on carpeting, tile or other

combustiblematerialotherthanwoodooringtheapplianceshall

be installed on a metal or wood panel extending the full width and

depth of the appliance.

Thebasereferredtoabovedoesnotmeanthere-proofbaseas

used on wood stoves. The protection is for rugs that are extremely

thickandlightcoloredtile.

WELL HEAD GAS INSTALLATIONS

Some natural gas utilities use “well head” gas. This may affect

the Btu output of the unit and promote sooting. Units shall not be

converted to use well head gas.

INSTALLATION IN RESIDENTIAL GARAGES

Gas utilization equipment in residential garages shall be installed

so that all burners and burner ignition devices are located not less

than18"(457mm)abovetheoor.

Such equipment shall be located, or protected, so it is not subject

to physical damage by a moving vehicle.

SPECIFICATIONS

Model FAW-40SPP FAW-40IP

Input BTU/HR (KW/H) 40,000 (11.7) 40,000 (11.7)

Height 72 1/2" (84.1mm) 72 1/2" (184.1mm)

Width 14 1/8" (35.9mm) 14 1/8" (35.9mm)

Depth 10 3/8" (26.4mm) 10 3/8" (26.4mm)

Gas Inlet Pipe 1/2" (12.7mm) 1/2" (12.7mm)

Vent Collar Type B Oval

4" (101mm) 4" (101mm)

CFM 275 275

ACCESSORIES

Side outlet, 10" (254mm)

maximumextension,xedregister

SOK-1

Rear outlet, 10" (254mm)

maximum extension, adjustable register

ROK-1

Vent enclosure, 24" (609mm)

[for rooms up to 96 1/2" 2451mm) in height]

FVE-24DB

Vent enclosure, 34" (86cm)

[for rooms up to 106 1/2" (2705mm) in height]

FVE-34DB

Vent enclosure, 46" (1168mm)

[for rooms up to 118 1/2" (3009mm) in height]

FVE-46DB

Oval-to-Roundueadapterkit4"(102mm) DV648DBF

CONVERSION KITS

Model Number Description Used On

DV1351 PropanetoNatural FAW40IPXLP-1

DV1349 NaturaltoPropane FAW40IPXNAT-1

DV1347 PropanetoNatural FAW40SPPXLP-1

DV1345 NaturaltoPropane FAW40SPPXNAT-1

INTRODUCTION

37134-6-0520 Page 3

• Due to high temperatures the appliance should be located

out of trafc and away from furniture and draperies.

• Children and adults should be alerted to the hazards of

high surface temperatures and should stay away to avoid

burns or clothing ignition.

• Young children should be carefully supervised when they

are in the same room as the appliance.

• Clothing or other ammable material should not be placed

on or near the appliance.

• Any safety screen or guard removed for servicing an ap-

pliance must be replaced prior to operating the appliance.

• Keep burner and control compartment clean.

• Installation and repair should be done by a QUALIFIED

SERVICE PERSON. The appliance should be inspected

before use and at least annually by a qualied service

person. More frequent cleaning may be required due to

excessive lint from carpeting, bedding materials, etc. It

is imperative that control compartments, burners and

circulating air passageways of the appliance be kept

clean.

• DO NOT put anything around the furnace that will obstruct

the ow of combustion and ventilation air.

• DO keep the appliance area clear and free from combus-

tible material, gasoline and other ammable vapors and

liquids.

• DO examine venting system periodically and replace

damaged parts.

• DO make a periodic visual check of pilot and burners.

Clean and replace damaged parts.

• CAUTION: Pilot hole cover must be kept tightly closed

during operation.

• DO NOT use this heater if any part has been under water.

Immediately call a qualied service technician to inspect

the heater and to replace any part of the control system

and any gas control which has been under water.

• This furnace must not be connected to a chimney ue

serving a separate solid-fuel burning appliance.

• IMPORTANT: This furnace has a washable permanent

type lter in the door which should be cleaned at least

once per year before the heating season. For dirty or

high use areas more frequent cleaning is required.

THIS IS A HEATING APPLIANCE

DONOTOPERATETHISAPPLIANCEWITHOUTFRONTPANELSINSTALLED.

INTRODUCTION (CONT'D)

When an existing Category 1 heater is removed or replaced, the

original venting system may no longer be sized to properly vent the

attached appliances. Instructions shall also indicate effects of an

improperlysizedventingsystem(formationofcondensate,leakage,

spillage, etc.) and shall specify the following test procedure:

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each

appliance connected to the venting system being placed

into operation could result in carbon monoxide poisoning

or death.

The following steps shall be followed for each appliance

connected to the venting system being placed into

operation, while all other appliances connected to the

venting system are not in operation:

1. Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and

horizontal pitch, as required in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Natural Gas and

Propane Installation Code, CSA B149.1 and these

instructions. Determine that there is no blockage or

restriction, leakage, corrosion and other deciencies

which could cause an unsafe condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which

the appliance(s) connected to the venting system are

located and other spaces of the building.

4. Close replace dampers.

5. Turn on clothes dryers and any appliance not connected

to the venting system. Turn on any exhaust fans, such

as range hoods and bathroom exhausts, so they are

operating at maximum speed. Do operate a summer

exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the thermostat

so appliance is operating continuously.

7. Test for spillage from draft hood equipped appliances

at the draft hood relief opening after 5 minutes of main

burner operation. Use the ame of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected in

accordance with National Fuel Gas Code, ANSI Z223.1/

NFPA 54 and/or Natural Gas and Propane Installation

Code, CSA B149.1.

9. After is has been determined that each appliance

connected

to the venting system properly vents when

tested as outlined above, return doors, windows,

exhaust fans, replace dampers and any other gas-red

burning appliance to their previous conditions of use.

37134-6-0520Page 4

SAFETY INFORMATION FOR USERS OF PROPANE GAS

Propane is a ammable gas which can cause res and explo-

sions. In its natural state, propane is odorless and colorless.

You may not know all the following safety precautions which

can protect both you and your family from an accident. Read

them carefully now, then review them point by point with the

members of your household. Someday when there may not

be a minute to lose, everyone's safety will depend on knowing

exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas

because of the odorant put in the Propane Gas. That's your

signal to go into immediate action!

• Do not operate electric switches, light matches, use your phone.

Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Closeallgastankorcylindersupplyvalves.

• Propane Gas is heavier than air and may settle in low areas

such as basements. When you have reason to suspect a gas

leak,keepoutofbasementsandotherlowareas.Stayout

untilreghtersdeclarethemtobesafe.

• Use your neighbor's phone and call a trained Propane Gas

servicepersonandtheredepartment.Eventhoughyoumay

not continue to smell gas, do not turn on the gas again. Do not

re-enterthebuilding,vehicle,trailer,orarea.

• Finally, lettheservicemanandreghterscheckforescaped

gas. Have them air out the area before you return. Properly

trainedPropaneGasservicepeopleshouldrepair theleak,

thencheckandrelightthegasapplianceforyou.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell

the odor of the chemical put into the gas. You must nd out if

you can smell the odorant in propane.Smokingcandecrease

your ability to smell. Being around an odor for a time can affect your

sensitivity or ability to detect that odor. Sometimes other odors in

theareamaskthegasodor.Peoplemaynotsmellthegasodoror

theirmindsareonsomethingelse.Thinkingaboutsmellingagas

odorcanmakeiteasiertosmell.

The odorant in Propane Gas is colorless, and it can fade under

some circumstances. For example, if there is an underground

leak,themovementofthegasthroughsoilcanltertheodorant.

Odorants in Propane Gas also are subject to oxidation. This fading

canoccurifthereisrustinsidethestoragetankorinirongaspipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

takesomeoftheodorantoutofthegas,reducingitsodorintensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest gas

odor.Ifyoudetectanyodor,treatitasaseriousleak.Immediately

go into action as instructed earlier.

SOME POINTS TO REMEMBER

• Learn to recognize the odor of Propane Gas. Your local Propane

Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use

ittondoutwhatthepropaneodorsmellslike.Ifyoususpect

thatyourPropaneGashasaweakorabnormalodor,callyour

Propane Gas Dealer.

• Ifyouarenotqualied,donotlightpilotlights,performservice,

ormakeadjustmentstoappliancesonthePropaneGassystem.

Ifyouarequalied,consciouslythinkabouttheodorofPropane

Gas prior to and while lighting pilot lights or performing service

ormakingadjustments.

• Sometimesa basementor aclosed-up house hasa musty

smell that can cover up the Propane Gas odor. Do not try to

lightpilotlights,performservice,ormakeadjustmentsinan

area where the conditions are such that you may not detect

theodoriftherehasbeenaleakofPropaneGas.

• Odor fade, due to oxidation by rust or adsorption on walls of

newcylindersandtanks,ispossible.Therefore,peopleshould

beparticularlyalertandcarefulwhennewtanksorcylinders

areplacedinservice.Odorfadecanoccurinnewtanks,or

reinstalledoldtanks,iftheyarelledandallowedtosettoo

longbeforerelling.Cylindersandtankswhichhavebeenout

of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question

about the gas odor, call your Propane Gas Dealer. A peri-

odic sniff test of the Propane Gas is a good safety measure

under any condition.

• If, at any time, you do not smell the Propane Gas odorant and

youthinkyoushould,assumeyouhavealeak.Thentakethe

same immediate action recommended above for the occasion

when you do detect the odorized Propane Gas.

• If you experience a complete "gas out," (the container is under

novaporpressure),turnthetankvalveoffimmediately.Ifthe

container valve is left on, the container may draw in some air

throughopeningssuchaspilotlightorices.Ifthisoccurs,some

new internal rusting could occur. If the valve is left open, then

treatthecontainerasanewtank.Alwaysbesureyourcon-

tainer is under vapor pressure by turning it off at the container

beforeitgoescompletelyemptyorhavingitrelledbeforeitis

completely empty.

37134-6-0520 Page 5

VENTILATION AND COMBUSTION AIR

WARNING

Danger of property damage, bodily injury or death, this furnace

and any other fuel burning appliance must be provided with

enough fresh air for proper combustion and ventilation of ue

gases. Most homes will require that outside air be supplied.

Do not draw air from a corrosive environment such as a

workshop or laundry room.

The requirements for providing air for combustion and ventilation are

listedintheNationalFuelGasCodesNFPA54/ANSIZ223.1(inCanada

-CAN/CGAB149).

NOTE:Airrequirementsforoperationofexhaustfans,kitchenventilation

systems,clothesdryers,replaceandanyotherfuelburningorventilating

equipment used in the space must be considered in determining

combustion air requirements.

VENTILATION AIR OPENINGS AND DUCTS

In determining the free area needed consideration must be given to the

blockingeffectoflouvers,grillsorscreensprotectingopenings.

— If a screen is used to cover openings it must not be smaller than

1/4" mesh.

— Use the free area of a louver or grill to determine the size opening

requiredtoprovidethefreeareaspecied.Ifthefreeareaisnot

knownassumea20%freeareaforwoodanda60%freeareafor

a metal louver or grill.

— Ducts must have the same cross sectional area as the free area of

the openings to which they connect.

— The minimum dimension of air ducts must not be less than 3 inches.

INSTALLATION IN AN UNCONFINED SPACE

Anunconnedspaceisanareaincludingallroomsnotseparatedby

doors with a volume greater than 50 cubic feet per 1,000 Btuh of the

combined total input rates of all appliances which draw combustion air

from that space. For example, a space including a water heater rated

at 40,000 Btuh input and a furnace rated at 40,000 Btuh requires a

volume of 4,000 cubic feet (50 x (40 + 40) = 4,000) to be considered

asunconned.Ifthespacehasan8ft.ceiling,theoorareaofthe

space must be 500 sq. ft. In general, particularly in older homes, a

furnaceinstalledinanunconnedspacewillnotrequireoutsideairfor

combustion. However in a "tight" newly constructed home, outside air

may be necessary to insure adequate combustion.

INSTALLATION IN A CONFINED SPACE

Aconnedspaceisanareawithvolumelessthan50cubicfeetper1,000

Btuh of the combined input rates of all appliances drawing combustion

airfromthatspace.Smallareassuchasequipmentroomsareconned

spaces.Furnacesinstalledinaconnedspacewhichsupplyheatedair

to areas outside the space must draw return air from outside the space

throughtightlysealedreturnairducts.Aconnedspacemusthave2

openings into the space for combustion air. One opening must be within

12 inches of the ceiling and the other must be within 12 inches of the

oor.Therequiredsizingoftheseopeningsisdeterminedbywhether

inside or outside air is used to support combustion, the method by which

the air is brought to the space (vertical or horizontal duct) and by the

total input rate of all appliances in the space. See Figure 1.

ALL AIR FROM INSIDE — CONFINED SPACE

Ifcombustionairistakenfromtheheatedspacethe2openingsmust

each have a free area of at least one square inch per 1,000 Btuh of

totalinputofallappliancesintheconnedspacebutnotlessthan100

square inches (645cm

) of free area.

Forexample: fora 40,000Btuh furnace onlyinthe connedspace

each opening must be 100 square inches (645cm

) each of free area.

WARNING

Combustion air must not be drawn from a heated space which

includes exhaust fans, replaces or other devices that may

produce a negative pressure in the space.

furnace

opening

confined

space

Figure 1

OUTDOOR AIR

Outletandinletaircanbebroughtintotheconnedspaceviaopenings

into a ventilated attic and ventilated crawl space.

furnace

outlet air

inlet air

attic ventilation louvers

crawl space ventilation louvers

Figure 2

CONFINED SPACE

Outdoor Air Using Vertical or Horizontal Ducts

Ifcombustionairistakenfrom outdoors through verticalducts,the

openings and ducts must have a minimum free area of one square

inch (6.5cm

) per 4,000 Btuh of total appliance input. In installations

drawing combustion air from a ventilated attic both air ducts must extend

above the attic insulation.

furnace

outlet air

inlet air ends one foot above floor

vertical

furnace

inlet air duct

outlet air duct

horizontal

Figure 3

Ifcombustionairistakenfromoutdoorsthroughhorizontalductsthe

openings and ducts must have a minimum free area of one square

inch (6.5cm

) per 2,000 Btuh of total appliance input.

37134-6-0520Page 6

QUALIFIED INSTALLING AGENCY

Installation and replacement of gas piping, gas utilization equipment or

accessories and repair and servicing of equipment shall be performed

onlybyaqualiedagency.Theterm"qualiedagency"meansany

individual,rm,corporationorcompanywhicheitherinpersonor

through a representative is engaged in and is responsible for (a)

the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

suchwork,familiarwithallprecautionsrequiredandhascomplied

with all the requirements of the authority having jurisdiction.

The installation must conform with local codes or, in the absence of

local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA

54* Natural and Propane Installation Code, CSA B149.1.

*Available from the American National Standards Institute, Inc., 11

West 42nd St., New York, N.Y. 10036.

CLEARANCES

1. In selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper

installation.

2. TheFAW-40canbeattachedtothewallorrecessedintothe

wall up to 9 1/2 inches (24.1cm) in depth. NOTE:

Do not place

combustible header or material on top of unit when

installed in wall. Maintain 3/4" minimum spacing above

heater.

3. The wall in which the furnace is recessed has (0) zero (0mm)

clearance to the furnace sides.

4. Whenusingsidedischargeregisters,SOR-1orSOK-1,the

furnace cannot be recessed into the wall.

5. Clearance to sidewall or combustible material is 4 inches

(10.2cm).

6. Ceiling clearance is 4 inches (10.2cm).

7. Floor and rear wall clearance is (0) zero inches (0mm).

8. Clearance of 18 inches (46cm) is required to adjacent wall or

combustiblematerialwhenushmountedSOR-1,sideoutlet

BEFORE INSTALLING CONSIDER THE FOLLOWING VENTING

1. A chimney for residential-type or low-heat gas utilization

equipment shall extend at least 3 feet (914mm) above the

highest point where it passes through a roof of a building and at

least 2 feet (610mm) higher than any portion of building within

a horizontal distance of 10 feet (3m).

2. Thisfurnacemustnotbeconnectedtoachimneyueserving

aseparatesolid-fuelburningappliance.

3. Uninsulated Single-Wall Metal Pipe shall not be used

outdoors in cold climates for venting gas utilization

equipment.

4. ATTENTION! This Fan Type Vented Wall Furnace is equipped

withaventsafetyswitch.Intheeventofspillageofueproducts

due to improper venting the vent safety switch will open, which

results in the main burners to "shut off".

ModelNo.FAW-40maybeventedasshowninFigure 4. The vent

capterminationmustbeatleast12feet(3.7m)abovetheoorand

must exhaust to the outdoors. Clearance to combustible construc-

tionisheldbythexedspacersat1inch(25mm)withB-1or(B-W)

vent pipe. Installation must conform to local codes.

A. 4" (102MM) ROUND (ALL PARTS PURCHASE LOCALLY EX-

CEPT ITEM 2)

1. TypeB-1roundpipe

2. PartNo.DV648DBF,4"(102mm)oval-to-roundueadapter

kit(seeaccessories)

3. SinglestorytypeB-1gasventsrequireabaseplateandone

pair of ceiling plate spacers.

4. Multi-storytypeB-1gasventsrequireabaseplate,onepair

ofceilingplatespacersattherstoorceilingandonepair

ofrestopspacersateachsuccessiveceilinglevel.

B. 4" (102MM) OVAL (ALL PARTS PURCHASE LOCALLY)

1. TypeB-1ovalpipeorB-Wventpipe

2. SinglestorytypeB-1or(B-W)gasventsrequireabaseplate

and one pair of ceiling plate spacers.

3. Multi-storytypeB-1or(B-W)gasventsrequireabaseplate,

onepairofceilingplatespacersattherstoorceilingand

onepairofrestopspacersateachsuccessiveceilinglevel.

C. 4" (102MM) OVAL IN-THE-WALL (ALL PARTS PURCHASE

LOCALLY)

1. TypeB-1ovalpipeorB-Wventpipe

2. TypeB-1ovalelbowsorB-Wovalelbows

3. SinglestorytypeB-1or(B-W)gasventsrequireabaseplate

and one pair of ceiling plate spacers.

4. Multi-storytypeB-1or(B-W)gasventsrequireabaseplate,

onepairofceilingplatespacersattherstoorceilingand

onepairofrestopspacersateachsuccessiveceilinglevel.

Stud space around gas vents must be free of obstructions and

building paper.

4" B-1 OVAL

SPACER

BASEPLATE

4" 45 DEG.

OVAL ELBOW

4" B-1 OVAL

SPACER

BASEPLATE

SPACER

4" B-1 OVAL

BRACKET

BASEPLATE

ADAPTER

4" B-1 Round

Figure 4

37134-6-0520 Page 7

Figure 5

UseU.L.listedgasventequipmentwheninstallingtheFAW-40.

For vent pipe running through walls, roof, and within one (1) inch

(25mm)ofcombustibleconstruction,useB-1or(B-W)[oneinch

(25mm)clearancetocombustibles]ventpipe.TypeB-2x4orType

B-2x6aretobeusedinconjunctionwithaListedrestopspacer.

Be sure baseplate is attached to top of furnace before inserting unit

into recessed wall installation.

INSTALLING OPTIONAL SIDE OUTLETS

Side outlet register, SOR-1 may be installed on one or both sides

of the furnace at the required clearances of 18 inches (457mm) to

adjacent wall or combustible material as shown in Figure 6.

1. Turn "OFF" all electric power to the furnace.

2. Remove the front panel from the furnace.

3. Remove the (2) #8 x 3/8" (9mm) screws that attach the inner

shield cover plate to the inner shield.

4. Scribe a line between the four dimples on the outer casing side

to form a square.

5. Drill a pilot hole within the scribed square on the outer casing.

Remove the sheet metal within the scribed square with a tin

snips or comparable tool. Attention! Do not cut the electrical

wires located between the outer casing and the inner shield.

6. Insert the 5" x 5" (127mm x 127mm) inner boot through the

outer casing. Align the clearance holes on the inner boot with

the screw holes on the inner shield. Attach inner boot to inner

shield with (2) # 8 x 3/8" (9mm) screws removed in Step 3.

7. Place the register over the 5 1/2" (140mm) square opening with

thelouverssetforthedesireddirectionandmarkthemounting

holes using the register as a template.

8. Drill (2) 1/8" diameter holes in cabinet side and attach the

9. InstallationofSOR-1iscompleted.

Sideoutletkit,SOK-1, 10" (254mm) boot assembly with register, for

warm air discharge into an adjoining room may be installed on either

side of the furnace at the required clearance of 4 inches (102mm)

to adjacent wall as shown in Figure 6.

ToinstallSOK-1,pleaseuseSteps1through5intheSOR-1instruc-

tionsforFAW-40furnaces.Now,usethefollowingStepstocomplete

installationoftheSOK-1.

1. Usingtheinnerandouterbootsasholetemplates,markand

drill (4) 1/8" (3mm) diameter holes in the inner shield and (4)

1/8" (3mm) diameter holes in the cabinet side.

2. Locate and cut a 6 3/4" (171mm) square opening through wall.

3. Attach furnace to wall (see Attaching Furnace to Wall).

4. Withfurnaceinplace,aftercheckingalignmentofsideoutlet

opening in wall and furnace, place the 9 3/8" x 9 3/8" (238mm

x 238mm) side outlet wall plate over outer boot, pass the outer

boot through the wall and attach side wall plate to furnace side

of wall with (2) #10 x 1 1/2" (38mm) provided screws.

5. Attach outer boot to the cabinet side with (4) #8 x 1/4" (6mm)

provided screws.

6. Position and attach inner boot to inner shield with (4) #8 x 1/4"

(6mm) provided screws.

7. Place the register over the 6 3/4" (171mm) square opening with

the louvers positioned for the desired discharge direction and

markthemountingholesusingtheregisterasatemplate.

8. Drill (2) 1/8" (3mm) diameter holes in the wall and attach the

9. InstallationofSOK-1iscompleted.

4" MINIMUM TO COMBUSTIBLE

WALL OR SURFACE

CLEARANCE FOR SIDE OUTLET KITS AND REAR REGISTER

KIT TO ADJACENT WALL

4" MINIMUM TO COMBUSTIBLE

WALL OR SURFACE

18" MIN. CLEARANCE TO

WALL OR COMBUSTIBLE

SURFACE USING MODEL

SOR-1 SIDE REGISTER.

WALL

5 1/2"

UNIT CANNOT BE RECESSED

WHEN SIDE REGISTERS ARE

USED.

WHEN SIDE REGISTERS ARE

NOT USED UNIT MAY BE RECESSED

UP TO 9 1/2"

6 1/4"

10 1/4"

REAR REGISTER OPENING

IN OUTER CABINET

12" 12"

TYPE B-1 OR

B-W OVAL

VENT PIPE

Figure 6

INSTALLING OPTIONAL REAR OUTLET

Rearoutletkit,10"(254mm)bootassemblywithregister,ROK-1

for warm air discharge into an adjoining room.

ATTENTION: Before furnace is attached to the wall, the wall opening

for the rear outlet must be cut, in addition to removal of the outer

andinnercasingknockoutsonfurnace.

The wall opening measurements for the rear outlet are the following.

A. Fromoortobottomofwallopeningis1011/16"(271mm).

B. From bottom of wall opening to top of wall opening is 8 1/2"

(216mm).

C. Wall opening width is 12 1/8" (308mm).

2. Scribealinebetweenthefourdimplesontheoutercasingback

to form a square. Drill a pilot hole within the scribed square

ontheoutercasingback.Removethesheetmetalwithinthe

scribed square with a tin snips or comparable tool.

3. Remove the (4) #8 x 3/8" (9mm) screws that attach the inner

casing close off plate to the inner casing.

Inserttheprivacyshieldthroughtheoutercasingbackandthe

innercasingback.Theprivacyshieldwillbeinfrontoftheinner

casingbackandbehindthecombustionchambertubes.Align

clearance holes on privacy shield with screw holes on inner

casingback.Attachprivacyshieldtoinnercasingbackwith(2)

#8 x 3/8" (9mm) provided. ATTENTION: The (2) #8 x 3/8" (9mm)

screws must be inserted from the front of the furnace.

5. Attach furnace to wall.

6. Align clearance holes on 8" x 12" (203mm x 305mm) boot with

screwholesonoutercasingbackandmarkboottobeush

with wall surface. Remove boot and cut to proper length.

7. Attach8"x12"(203mmx305mm)boottooutercasingback

with (6) #8 x 3/8" (9mm) screws provided.

37134-6-0520Page 8

8. Align clearance holes on 6" x 10" (152mm x 254mm) duct with

screwholesoninnercasingbackandmarkducttobe21/4"

(57mm) shorter than 8" x 12" (203mm x 305mm) boot. Remove

duct and cut to proper length.

9. Attach6"x10"(152mmx254mm)ducttoinnercasingbackwith

(4) #8 x 3/8" (9mm)screws removed in Step 3, 2 on top and 2

on bottom.

10. Insert rear register into 8" x 12" (203mm x 305mm) boot. Attach

rear register to wall with (2) #10 x 1"(25mm) screws provided.

11. InstallationofROK-1iscompleted.

LOCATING FURNACE ON WALL

The furnace is to be located on a wall. The furnace is 14 1/8" (35.9cm)

in width and can be recessed into the wall with typical stud spacing.

A template is provided in furnace carton for locating gas line

connection. Also, refer to Figure 7 for positioning the furnace on

wall and for locating gas line connection.

LOCATING GAS SUPPLY

Thegaslinecanenterthefurnaceeitherthroughtheoororwall.

The gas line opening should be made at this time. Location of the

openingwillbedeterminedbythepositionofoorjoistsandthe

valve and union used for servicing. See Figure 7.

72 3/4"

14 3/8"

CUT OUT OPENING FOR RECESSED MOUNTING

RECESSED MOUNTING

LOCATION

2 1/8"

GAS LINE

HOLE 1 1/4"

ELECTRICAL WIRING HOLE

GAS LI NE/ELECTRICA L OPENINGS FOR

RECESSED AND SURFACE MOUNT

0.0722

0.5249

0.2613

0.2395

0.2624

GAS LINE/ELECTRICAL OPENING

FOR RECESSED AND

SURFACE MOUNTING

SURFACE

MOUNTING

HOLES

OVAL TO ROUND KIT

MOUNTING HOLES

1 1/4" GAS

LINE HOLE

ELECTRICAL

WIRING

HOLE

RECESSED

MOUNTING

HOLES

Figure 7

LOCATING ELECTRIC SUPPLY

A7/8"(22mm)diameterknockoutisprovidedatthebottomofthe

leftandrightsidepanels.Athree-prong(grounding)plugassembly

is located within the control compartment (bottom) of the furnace.

Pleaseremove7/8"(22mm)knockoutfromappropriatesidepanel

when routing plug assembly to an electrical outlet.

INSTALLATION OF THREE-PRONG (GROUNDING) PLUG ASSEMBLY

1. Disconnect nylon cap on 3' (914mm) plug assembly from nylon

plug on wiring harness. Remove 3' (914mm) plug assembly

from control compartment (bottom) of the furnace.

2. Remove7/8"(22mm)knockoutfromappropriatesidepanel.

3. Insert nylon cap on 3' (914mm) plug assembly into the 7/8"

(22mm) hole in the side panel.

4. Connect nylon cap on 3' (914mm) plug assembly to nylon plug

on the wiring harness.

5. Place 7/8" (22mm) strain relief bushing around the cord of the

3' (914mm) plug assembly. Insert 7/8" (22mm) strain relief

bushing into the 7/8" (22mm) hole in the side panel.

ATTENTION! The 7/8" (22mm) strain relief bushing is located

within the same yellow envelope as the Installation Instructions

and Owner's Manual.

ATTACHING FURNACE TO WALL

When attaching furnace to the wall remove that portion of baseboard

and molding on the wall which is behind the furnace. Attach furnace

to wall, at the outer casing top, with (2) toggle bolts provided and

tooor,attheoutercasingbottom,with(2)#10x11/2" (38mm)

screws provided.

GAS SUPPLY

Checkalllocalcodesforrequirements,especiallyforthesizeand

typeofgassupplylinerequired.OnNaturalGaslineslessthan

75' (22.9m) long, use 1/2" (13mm) pipe; on longer runs, use 3/4"

(19mm) iron pipe or equal. On Propane Gas lines please consult

Propane Gas supplier.

INSTALLING A NEW MAIN GAS SHUT-OFF

Eachapplianceshouldhaveitsownmanualgasshut-off.

Amanualmaingasshut-offshouldbelocatedinthevicinityofthe

unit. Where none exists, or where its size or location is not adequate,

contact your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

totheactionofliqueedpetroleumgases.Thegaslinesmustbe

checkedforleaksbytheinstaller.Thisshouldbedonewithasoap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.

Never use an exposed ame to check for leaks. Appliance must

be disconnected from piping at inlet of control valve and pipe

capped or plugged for pressure test. Never pressure test with

appliance connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required by

theNationalFuelGasCodethatadriplinebeinstallednearthegas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

Figure 8

METHOD OF INSTALLING A TEE FITTING SEDIMENT TRAP

The use of the following gas connectors is recommended:

— ANSZ21.24ApplianceConnectorsofCorrugatedMetalTubing

and Fittings

— ANSZ21.45AssembledFlexibleApplianceConnectorsofOther

ThanAll-MetalConstruction

The above connectors may be used if acceptable by the authority

having jurisdiction.

PRESSURE TESTING OF THE GAS SUPPLY SYSTEM

1. Tochecktheinletpressuretothegasvalve,a1/8"(3mm)N.P.T.

plugged tapping, accessible for test gauge connection, must

be placed immediately upstream of the gas supply connection

to the appliance.

2. The appliance and its individual shut-off valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

1/2psig(3.5kPa).

3. The appliance must be isolated from the gas supply piping

systembyclosingitsindividualmanualshut-offvalveduring

any pressure testing of the gas supply piping system at test

pressuresequaltoorlessthan1/2psig(3.5kPa).

37134-6-0520 Page 9

To clean burner port disconnect the gas supply to the valve, and

remove the screws fastening the burner door. After removing the

burner door from the burner box, remove each main burner. Pilot

mounting bracket willneed to be unscrewed andmoved out of

the way to remove all burners. Burners can be blown out using

compressed air or by blowing through them. Be sure there is no lint

orforeigndebrisblockingtheburnerports.Reassembleusingthe

same screws earlier removed and locate pilot in the same position

as before and noted above.

SPARK

ELECTRODE

THERMOCOUPLE

PILOT

BURNER

STANDING PILOT

PILOT LOCATION END VIEW

PILOT SHIELD

THERMOCOUPLE

PARK

ELECTRODE

STANDING PILOT SHOWN

BURNER

PILOT

HOT SURFACE

IGNITOR

FLAME

ROD

GROUND

ELECTRODE

3/8" TO 1/2"

PILOT FLAME

IP-MODEL PILOT

Figure 10

Figure 11

CLEANING COMBUSTION (EXCHANGER) ASSEMBLY

A QUALIFIEDSERVICEPERSON should remove the combustion

(exchanger)assemblyanduebafes.Applyairpressuretothe

insideofthecombustion(exchanger)assemblyanduebafesin

order to clear all passageways.

OILING THE MOTOR

The fan motor should be cleaned and oiled once each heating

season. Oil holes are located on the top at each end of the motor.

Use a few drops of #10 motor oil. To clean the motor, blow air

through its ventilation openings with a vacuum cleaner or low

pressure air source.

WIRING

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

Code, CSA C22.1, if an external electrical source is utilized. This

appliance is equipped with a three-prong [grounding] plug for

ATTENTION! If one of the above procedures results in pressures in

excessof1/2psig(14"w.c.)(3.5kPa)ontheappliancegasvalve,

it will result in a hazardous condition.

CHECKING MANIFOLD PRESSURE

Both Propane and Natural Gas valves have a built-in pressure

regulatorinthegasvalve.NaturalGasmodelswillhaveamanifold

pressureofapproximately4.0"w.c.(.996kPa)atthevalveoutlet

with the inlet pressure to the valve from a minimum of 5.0" w.c.

(1.24kPa)for thepurpose ofinput adjustmenttoa maximumof

10.5"w.c.(2.615kPa).PropaneGasmodelswillhaveamanifold

pressure approximately 10.0" w.c. (2.49kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 11.0" w.c.

(2.739kPa)forthepurposeofinputadjustmenttoamaximumof

13.0"w.c.(3.237kPa).

A 1/8" (3mm) N.P.T. plugged tapping, accessible fortest gauge

connection, is located on the outlet side of the gas control.

Thebuilt-inregulatorcomesonatapproximately 1/4thpressure

and full on in 10 seconds.

Figure 9

HIGH ALTITUDES

For altitudes/elevations above 2,000 feet (610m), input ratings should

be reduced at the rate of 4 percent for each 1,000 feet (305m) above

sea level. For Canadian high altitude applications, this appliance is

suitable for installation at elevations between 0 feet (0m) and 4,500

feet (1,372m) without change.

PIEZO PILOT IGNITOR INSTRUCTIONS

Depressingtheredbuttoncompletelycausesasparktooccuratthe

pilot. This is a substitute for a match which requires opening the pilot

hole cover. To light the pilot, it is important that the electrode be 1/8"

(3mm)fromthethermocouple.Thesparkmustoccuratthepoint

theburneramehitsthethermocouple.Theendoftheelectrode

will be red hot with the pilot on.On a new installation with air in the

gas line, it is suggested that a match be used. The match will light

the pilot faster than the piezo under this condition.

PROPER PILOT FLAME

The correctpilot ame(Figure 10) will be blue, extending past

thethermocouple.Theamewillsurroundthethermocouplejust

below the tip.

NaturalGaspilotsrequireadjustingwhentheinletgaspressure

isabove5"w.c.(1.245kPa).Removethepilotcoverscrewonthe

control valve (Figure 9),andturntheadjustmentscrewclockwiseto

reduceame.Replacepilotcoverscrewtoeliminategasleakage.

Propane Gas will not require adjustment.

Afteruse,cleaningmayberequiredfortheproperame.

PROPER MAIN BURNER FLAME

Thecorrect amewillbe ashort, blueinnerame withamuch

larger,lightblue,outerame.Theburnerdoesnothaveaprimary

airadjustment.Theamewillbecorrectifthefactory-setpressure

andoriceopeningareused.Afterthefurnacehasbeenoperating,

theburnerportsmaybeblockedbyforeignmattercarriedinby

combustion air. Therefore, cleaning of the burner may be needed

forproperame.

IP-MODELPILOT

STANDINGPILOT

PILOTLOCATIONENDVIEW

STANDINGPILOTSHOWN

37134-6-0520Page 10

your protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle. Do

not cut or remove the grounding prong from this plug. For an

ungrounded receptacle, an adapter, which has two prongs and a

wire for grounding, can be purchased, plugged into the ungrounded

receptacle and its wire connected to the receptacle mounting screw.

With this wire completing the ground, the appliance cord plug can

be plugged into the adapter and be electrically grounded. A 7/8"

(22mm) hole is provided in the junction box for use with a conduit

connector if local codes require this type of protection.

OPERATING INSTRUCTIONS

This heater is equipped to operate manually. Remove the front

doortogainaccesstothevalve.TurnthegascontrolfromtheON

position to PILOT to turn the heater off, or to the OFF position to

turn the heater and pilot off.

To Conserve Gas: Turn off pilot when heater is not in use.

INSTALLING ON/OFF DEVICE

To install an On/Off device (such as a wall switch, remote, toggle

switch or thermostat), remove the wire nut from the two wires from

thevalve.RunadditionalwirefromthevalvewirestotheON/OFF

device. Install the On/Off device in the same room as the furnace

following the installation instructions supplied with it. In the absence

ofinstructions,installtheOn/Offdevice4to5feetabovetheoor

on an interior wall not affected by another heating source (i.e. stove

or water heater) or the temperature of an adjoining room.

INSULATED VENT ENCLOSURE

Ventedwallfurnacesinstalledinbuildingswithatroofscanhave

poor venting. The cold vent pipe will have a delay in proper venting

and cause the wall furnace to shut "OFF" by the vent safety switch.

Topreventdelayedventingaswellascondensationofueproducts

an insulated vent enclosure is recommended.

Use type B vent pipe and maintain at least a one inch (25mm)

clearance to combustibles.

Use metal thimble to protect vent pipe as it passes through

combustibles.

Figure 12

VENT SAFETY SHUT-OFF SYSTEM

This appliance must be properly connected to a venting system.

Thisapplianceisequippedwithaventsafetyshut-offsystem.

WARNING

Operation of this wall furnace when not connected to

a properly installed and maintained venting system or

tampering with the vent safety shut-off system can result in

carbon monoxide (CO) poisoning and possible death.

This furnace is equipped with a manual reset vent safety switch.

Themanualresetventsafetyswitchwillcausegasowtothemain

burnersto"shutoff"duetoimproperventingorablockedue.

To reset the manual reset vent safety switch:

1. Remove front panel.

2. Depress manual reset button. The manual reset vent safety

switch is located on the draft diverter.

3. Replace front panel.

If the manual reset vent safety switch continues to "shut off" the

gasowtothemainburnersaqualiedservicepersonmustbe

contactedtoinspectforimproperventing,blockageintheventpipe

or the manual reset vent safety switch for being defective.

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

SPT-3 CORDSET

——— —— ——————————————— —

CORDON SPT-3

WHITE (BLANC)

BLACK (NOIR)

MOTOR

————— —————

MOTEUR

YELLOW (JAUNE)

RED/WHT (ROUGE/BLANC)

YELLOW

JAUNE

WHITE

BLANC

BLACK

NOIR

RED/WHT

ROUGE/BLANC

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

24 VOLTS

MOTOR

————— —————

MOTEUR

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

120 VOLTS

BLACK

NOIR

RED/WHT

ROUGE/BLANC

LOW VOLTAGE (BAS VOLTAGE)

120 VOLTS

JUNCTION BOX

—— —— ——— —————————————— ——

BOÎTE DE JONCTION

RED/WHT

ROUGE/BLANC

GAS VALV E

——— —— ————————————— —

VALVE DE GAZ

BLACK (NOIR) BLACK (NOIR)

RED/WHT (ROUGE/BLANC)

LIMIT CONTROL

——— — ——————————————— —

CONTRÔLE

LIMITE

WIRING DIAGRAM

————————————————————

CÂBLAGE DE DIAGRAMME

VENT SAFETY

——— —— ——————————— —

SÛRETÉ DE

L’ÉVENT

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

IF ANY OF THE ORIGINAL WIRE AS SUPPLIED

WITH THIS UNIT MUST BE REPLACED, IT MUST

BE REPLACED WITH 150°C THERMOPLASTIC

4/64 THICK OR ITS EQUIVALENT.

120V. 60Hz. LESS THAN 3 AMPS

S´IL YAUN FIL ORIGINAL FOURNI AVEC

L´APPAREIL QUI DOIT ÊTRE REMPLACÉ. IL DOIT

ÊTRE REMPLACÉ AVEC UN ÉQUIVALENT À FIL

4/64” THERMOPLASTIQUE 150°C.

120V. 60Hz. MOINS DE 3 AMPS.

—————— ———————————————————————————————————————————————

LADDER WIRING DIAGRAM

——————————————————————————

ÉCHELLE ÉLECTRIQUE

SCHÉMATIQUE

BLK (NOIR)

GRN (VERT)

WHT (BLANC)

SPP UNITS

GAS VALV E

——— —— ————————————— —

VALVE DE GAZ

LIMIT CONTROL

——— — ——————————————— —

CONTROL DE

TOLERANCE

BLACK

NOIR

BLACK

NOIR

VENT SAFETY

——— — ——————————————— —

SÛERTÉ DE

L’ÉVENT

WIRE NUT / ON/OFF DEVICE

——— — —————————————————————————————— —

FILS TORSADÉS / ON/OFF

PÉRIPHÉRIQUES

WIRE NUT / ON/OFF DEVICE

——— — —————————————————————————————— —

FILS TORSADÉS / ON/OFF

PÉRIPHÉRIQUES

LIMIT CONTROL

——— — ——————————————— —

CONTRÔLE

LIMITE

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

SPT-3 CORDSET

——— —— ——————————————— —

CORDON SPT-3

WHITE (BLANC)

BLACK (NOIR)

MOTOR

————— —————

MOTEUR

WIRING DIAGRAM

————————————————————

CÂBLAGE DE DIAGRAMME

VENT SAFETY

——— —— ——————————— —

SÛRETÉ DE

L’ÉVENT

YELLOW (JAUNE)

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

IF ANY OF THE ORIGINAL WIRE AS SUPPLIED

WITH THIS UNIT MUST BE REPLACED, IT MUST

BE REPLACED WITH 150°C THERMOPLASTIC

4/64 THICK OR ITS EQUIVALENT.

120V. 60Hz. LESS THAN 3 AMPS

S´IL YAUN FIL ORIGINAL FOURNI AVEC

L´APPAREIL QUI DOIT ÊTRE REMPLACÉ. IL DOIT

ÊTRE REMPLACÉ AVEC UN ÉQUIVALENT À FIL

4/64” THERMOPLASTIQUE 150°C.

120V. 60Hz. MOINS DE 3 AMPS.

—————— ———————————————————————————————————————————————

RED/WHT (ROUGE/BLANC)

RED (ROUGE)

LADDER WIRING DIAGRAM

——————————————————————————

ÉCHELLE ÉLECTRIQUE

SCHÉMATIQUE

RED/WHT

ROUGE/BLANC

TRANSFORMER

——— —— —————————————————— —

TRANSFORMATEUR

24 VOLTS

120 VOLTS

RED/WHT

ROUGE/BLANC

BLACK

NOIR

RED/WHT

ROUGE/BLANC

BLACK

NOIR

LOW VOLTAGE (BAS VOLTAGE)

120 VOLTS

JUNCTION BOX

—— —— ——— —————————————— ——

BOÎTE DE JONCTION

RED/WHT

ROUGE/BLANC

VENT SAFETY

——— — ——————————————— —

SÛERTÉ DE

L’ÉVENT

LIMIT SWITCH

——— — ——————————————— —

CONTRÔLE DE

TOLÉRANCE

BLK (NOIR)

GRN (VERT)

WHT (BLANC)

BLK (NOIR)

IP UNITS

YELLOW

JAUNE

WHITE

BLANC

BLACK

NOIR

MOTOR

————— —————

MOTEUR

AUTO FAN

——— —— ——————————— —

VENTILATEUR

AUTO

ON/OFF DEVICE

——— — ——————————————— —

ON/OFF

PÉRIPHÉRIQUES

WIRE NUT / ON/OFF DEVICE

——— — —————————————————————————————— —

FILS TORSADÉS / ON/OFF

PÉRIPHÉRIQUES

WIRE NUT

——— — ——————————————— —

FILS TORSADÉS

SPP IP

Figure 13

BURNER BOX

GAS VALVE

JUNCTION BOX-



TRANSFORMER

LIMIT SWITCH

FAN SWITCH

VENT LIMIT SWITCH

FLUE CONNECTOR

FAN

IEZO

IGNITOR

DRAFT DIVERTER

Figure 14

37134-6-0520 Page 11

TO ADJUST:

1. Remove the pilot adjustment cover screw.

2. Turntheinneradjustmentscrewclockwise

to decrease

orcounterclockwise

toincreasepilotame.Pilotad-

justmentisshippedatfullowrate.Turntheinneradjustment

screwclockwise

if the inlet pressure is too high.

3. Replace the cover screw after the adjustment to prevent gas

leakage.

OFF

IGNITOR

CONTROL

INLET PRESSURE TAP

OUTLET PRESSURE TAP

PILOT ADJUSTMENT-

UNDER CAP SCREW

PILOT OUTLET

PRESSURE REGULATOR

ADJUSTMENT-UNDER CAP

SCREW

GAS FLOW

IGNITOR

CONTROL

TO 24 V. THERMOSTAT

TO 24 V. COMMON ON TRANSFORMER

TO 24 V."HOT" ON TRANSFORMER

WIRING

I P-MODEL GAS VALVE AND WIRING

IGNITOR-PILOT ASSY.

FAN

SWITCH

MOTOR

HONEYWELL IP

SMART VALVE

120 VAC

LIMIT

CONTROL

VENT SAFETY

LIMIT

THERMOSTAT

40 VA TRANSFORMER

24 VAC

120VAC

VALVE CONTROL

CONNECTOR

L1 "HOT"

L2 NEUTRAL

LADDER WIRING DIAGRAM-IP VALVE

Figure 15

SERVICE AND MAINTENANCE SUGGESTIONS

Call Serviceman

GENERAL: Allfurnaceshavebeenre-testedtocheckforproper

operation.Thisincludes,mainburnerame,pilotame,fanoperation,

fan control, limit control and valve operation. If the furnace fails to

functiononinitialinstallation,itisadvisabletore-checkthefollowing:

1. 115 volts to the junction box.

2. Inlet gas pressure.

3. The 24 volt system.

4. Type of gas being used and that shown on the rating label.

STANDING PILOT MODEL

Servicing the Pilot and Main Burners, Pilot Orice, Thermo-

couple, and Main Burner Orices: Disconnect the gas supply at

the inlet to the control valve. Then remove the burner door to gain

access to the above listed components.

IF ELECTRODE DOES NOT PRODUCE SPARK:

1. Checkwireconnections.

2. Checkgapforpilotburnertotheelectrodetip.Shouldbebetween

1/8" (3mm) and 3/16" (5mm). Electrode wire and tip must be

more than 1/4" (6mm) away from all other metal components.

IF PILOT DOES NOT LIGHT BY ANY MEANS:

1. Checkvalveknobforbeinginthe"Pilot"position.

2. Checkpilotadjustmentforbeingfullopen(counterclockwise

to open).

3. Ifgasisavailableinthesupplytubing,thepilotoriceand/or

pilot burner is probably restricted by a spider web. Clean pilot

assembly and relight.

IF PILOT DOES NOT REMAIN ON AFTER RELEASING KNOB:

1. Follow instructions and hold button down longer and harder.

2. Determineifpilotameextendspastthermocouple;ifnot,adjust

input or clean pilot burner.

3. Replace thermocouple if millivolts read less than 15 millivolts.

MAIN GAS VALVE DOES NOT OPEN WHEN GAS CONTROL IS

TURNED TO ON:

1. Checkfor24voltstovalvebyremovingonewireandtouching

to the SAME TERMINAL it was on. Terminal should have a

lightspark.DO NOT SHORT ACROSS TERMINALS, AS IT

WILL BURN OUT THE GAS CONTROL.

2. Tocheckforlinevoltagetofurnace,removefrontpaneland

shortacrosstwo-terminalfancontroltoallowfantooperate

Figure 14.

CAUTION

Label all wires prior to disconnection when servicing controls.

Wiring errors can cause improper and dangerous operation.

Verify proper operation after servicing.

IP-MODEL PILOT

This heater is using a Honeywell "Smart Valve" system for intermittent

pilot ignition.

On a call for heat by the control turns on a 24 volt mini hot surface

ignitor which lights a pilot that in turn lights the main burner. The gas

valve used in this system is a step opening which opens at a lower

pressure for ignition and then steps to a full inlet pressure of 4" H

pressureonNaturalGasand10"H

0 pressure on Propane Gas.

PILOT FLAME ADJUSTMENT

Thepilotameshouldenvelop3/8to1/2inch(10to13mm)ofthe

tipoftheamerod.See Figure 10.

37134-6-0520Page 12

A. This appliance is equipped with an ignition device which

automatically lights the pilot.

Do not try to light the pilot by hand.

B. BEFORE OPERATING smell all around the appliance area

for gas. Be sure to smell next to the oor because some

gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the re

department.

C. Use only your hand to slide the gas control knob. Never

use tools. Force or attempted repair may result in a re

or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualied service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

STANDING PILOT

LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE OPERATING

1. Turn off all electric power to appliance if service is to be

performed .

2. Remove control access panel (front panel).

3. Push in gas control knob slightly and turn clockwise

to "OFF." Do not force.

4. Replace control access panel (front panel).

TO TURN OFF GAS TO APPLIANCE

1. STOP! Read the safety information above.

2. Turn off all electric power to the appliance.

3. Remove control access panel (front panel).

4. Turn gas control knob clockwise to "OFF

GAS CONTROL SHOWN IN “OFF” POSITION

5. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the oor. If you smell gas, STOP!

Follow "B" in the safety information above. If you don't

smell gas, go to the next step.

6. Remove the pilot access cover located on the combustion

chamber.

7. Find pilot - follow metal tube from gas control. The pilot

is located between the two burner tubes behind the pilot

access cover.

8. Turn gas control knob counterclockwise

"PILOT."

Push and hold red reset button down completely and

repeatedly push the ignitor button until the pilot burner

is lit. Pilot may also be lit with a match. Continue to hold

the red reset button down for about one (1) minute after

the pilot is lit. Release button and it will pop back up. Pilot

should remain lit. If it goes out, repeat steps 5 through 10.

• If button does not pop up when released, stop and

immediately call a qualied service technician or gas

supplier.

• If the pilot will not stay lit after several tries, turn the

gas control knob to "OFF" and call your service tech-

nician or gas supplier.

10. Replace pilot access cover.

11. Turn gas control knob counterclockwise

to "ON."

12. Replace control access panel (lower front panel).

13. Turn on all electric power to the appliance.

OPERATING INSTRUCTIONS

WARNING

If you do not follow these instructions exactly, a re or explosion may result causing property damage,

personal injury or loss of life.

37134-6-0520 Page 13

1. STOP! Read the safety information above.

2. Turn off all electric power to the appliance.

3. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot

by hand.

OFF

IGNITOR

CONTROL

GAS FLOW

GAS VALVE SHOWN IN OFF POSITION

HONEYWELL IP SMART VALVE

4. Remove front panel door.

5. Slide gas control switch to "OFF."

6. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the oor. If you smell gas, STOP!

Follow "B" in the safety information above. If you don't

smell gas, go to the next step.

7. Slide gas control switch to "ON".

8. Replace front panel door.

9. Turn on all electric power to the appliance.

10. If the appliance will not operate, follow the instructions

"TO TURN OFF GAS TO APPLIANCE" and call your service

technician or gas supplier.

A. This appliance is equipped with an ignition device which

automatically lights the pilot.

Do not try to light the pilot by hand.

B. BEFORE OPERATING smell all around the appliance area

for gas. Be sure to smell next to the oor because some

gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the re

department.

C. Use only your hand to slide the gas control knob. Never

use tools. Force or attempted repair may result in a re

or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualied service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

INTERMITTENT PILOT (IP)

LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE OPERATING

OPERATING INSTRUCTIONS

1. Turn off all electric power to the appliance if service is to

be performed.

2. Remove front panel door.

3. Slide gas control switch to "OFF."

4. Replace front panel door.

TO TURN OFF GAS TO APPLIANCE

WARNING

If you do not follow these instructions exactly, a re or explosion may result causing property damage,

personal injury or loss of life.

37134-6-0520Page 14

START

System Check

Trial for

Ignition

Main Burner

Operation

END



Pilot Valve Opens

Ignitor Powered

Flame Signal

Detected

Call for Heat



Ignitor OFF

Main Valve Opens

Internal Check

Pilot Light and Flame is

Sensed During Trial For

Ignition (1)

Apply 24 VAC

To Appliance

Main Pilot Valves

Call for Heat Ends

Flame Signal

Lost?



Pilot Valve Ignition OFF

Wait for Flame Signal to

Disappear



Pilot Valve Closes

Ignition OFF

Main Pilot

Valves Close

Flame Lost More

Than 5Times in

One Call for Heat

5 Minute Retry Delay

3 Second Flame Recycle

Delay

YES

(1) Ignitor will turn OFF about 30 seconds into the trial for ignition if the pilot flame has not lit. It will turn back ON for the final 30 seconds

of the 90 second trial for ignition. The pilot valve will be energized during the entire trial for ignition. This is normal operation for this gas

ignition system.

SEQUENCE OF OPERATION

37134-6-0520 Page 15

START

IP SYSTEM TROUBLESHOOTING SEQUENCE



Turn OFF Gas Supply

Disconnect System Control

Harness

Set Gas Control to Call for

Heat

Check for Proper Voltage at

Control Harness (See Inset A-

Vo ltageShouldbe 24V

Between Switch and 24V

Common, and 24V Between

24V Common and 24V Hot.)

Plug Harness into SmartValve

Control

Wait for Internal Check Delay

(SV9501)

Igniter Warms UP and Glows

Red

Note: Igniter Will Cycle OFF

and Back ON Once During the

90 Second Ignition Trial



Turn On Gas Supply

Pilot Burner Lights

Main Valve Opens and

Main Burner Lights

System is Okay

Check

Line Voltage Power

Low Voltage Transformer

Limit Controller

Wiring



Unplug Pilot Burner Cable.

Measure Voltage at SmartValue HSI

Element Output (See Inset B) 24V

Nominal

Replace Igniter/Flame Rod

Assembly

Reconnect Pilot Burner Cable

Check that Pilot Gas is Flowing

Wait to Assure Pilot Gas Tubing is

Purged.

Measure Voltage Between 24V Hot

and 24V Common Leads to

SmartValve Control. Must Measure

at Least 19.5 VAC with Igniter

Powered. See InsetAto Identify

Proper Lead. This Check Must be

Done with the SmartValve Control

Connected and Igniter Powered.

Replace Igniter/Flame Rod

Assembly



Check that Pilot Flame Makes

Good Contact with Pilot Burner

Flame Rod

Check for Good Electrical

Connection Through the Pilot

Tubing

If Both of the Above are Good,

Replace Igniter/Flame Rod

Cycle Gas Control OFF and Back

Main Burner Lights

YES

Replace SmartValve Control

Reconnect Pilot Burner Cable

Replace SmartValve Control

Check Transformer and Line Volt

Supply

Replace SmartValve Control

SmartValve System Troubleshooting Sequence

Note: Before Troubleshooting, Become Familiar

with the Sequence of Operation

HSI

Terminals

INSET B

End View

of Control

Harness

Connector

EFT

Output

24 Volt

Hot

Volts

24 Volt

Common

Volts

24 Volt

INSET A

37134-6-0520Page 16

USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

INDEX

NO.

PART

NO.

DESCRIPTION

1 WFA115 GASKET-HEADER

2 DV1247 TOP PLATE (USA)

2 15668 TOPPLATE(CANADA)

3 R3165 DOOR CLIP (2 REQUIRED)

4 39476 CASINGSIDE-RIGHT

5 DV1203 CASINGBACK

6 39476 CASINGSIDE-LEFT

7 DV1248 AIRDROP(INCLUDESNO.51)

8 DV1231 TURBULATOR (3 REQUIRED)

9 DV1250 DIVIDER PLATE

10 DV1234 OUTLET BOX

11 DV1225 OUTLET BOX COVER

12 R3177 VENTSAFETYSWITCH

13 R3161 FANBLADE

14 R3166 FANMOTOR

15 DV1246 MOTORMOUNTINGBRACKET

16 R1536 BUSHING(5REQUIRED)

17 R1499 RUBBER GROMMET (4 REQUIRED)

18 R1454 BRASSBUSHING(4REQUIRED)

19 R3164 DOOR CLIP (2 REQUIRED)

20 DV1251

INNERSHIELD-RIGHT

(INCLUDESNO.23)

21 R6176 FANCONTROLSWITCH

22 R3176 LIMIT SWITCH

23 DV1253

INNERSHIELDCOVERPLATE

(2 REQUIRED)

24 DV1254 INNERSHIELDFRONT(SPP)

24 33416 INNERSHIELDFRONT(IP)

25 R3163 FILTERRETAINER

26 R3162 FILTER

27 DV1252

INNERSHIELD-LEFT

(INCLUDESNO.23)

28 DV1256 EXCHANGERASSEMBLY

29 DV1235 PILOT BRACKET (IP)

30 R3232 PILOT-NATURAL (IP)

30 R3233 PILOT-PROPANE (IP)

31 P8851 ORIFICE-NATURAL (3 REQUIRED)

31 P8860 ORIFICE-PROPANE (3 REQUIRED)

32 DV1236 MANIFOLD

33 DV1258 CASINGFRONT

34 P112 MANIFOLDUNION

35 R1109 BUSHING(3/8x1/2)

35 R9502 BUSHING(3/8x3/4)-NATURAL(IP)

36 R5655 GASVALVE-PROPANE (SPP)

36 R2148 GASVALVE-NATURAL(SPP)

36 R3170 GASVALVE-NATURAL(IP)

36 R3171 GASVALVE-PROPANE (IP)

37 R2708 PIEZOIGNITOR(SPP)

38 FF160 PIEZO BRACKET (SPP)

39 DV1318 OBSERVATIONHOLECOVERPLATE

40 DV1242

BURNERCOMPARTMENTFRONT

(SPP)

41 DV1237 BURNERCOMPARTMENTBODY

42 M148 MANIFOLDGASKET

43 GWT168 AIRSHUTTERFRONT(PROPANE)

44 GWT169 AIR SHUTTER REAR (PROPANE)

45 R3031 BURNER(3REQUIRED)

46 DV1239 BURNERBRACKET

47 UH452

TRANSFORMERMOUNTING

BRACKET (IP)

47 UH810

TRANSFORMERMOUNTING

BRACKET (SPP)

48 R1995 TRANSFORMER(SPP)

48 R998 TRANSFORMER(IP)

49 UH451 JUNCTIONBOXCOVER

50 DV572 JUNCTIONBOX

51 DV1260 COVERPLATE-AIRDROP

52 R1410 BUSHING

53 R690 CORD SET

54 R1515 BUSHING

55 DV1215 BOTTOM PLATE

56 R3034 PILOT-NATURAL(SPP)

56 R3035 PILOT-PROPANE (SPP)

57 GWT021 PILOT BRACKET (SPP)

58 R3180 ELECTRODEANDWIRE(SPP)

59 R2256 THERMOCOUPLE-18"(SPP)

N/S DV1261 PILOTTUBINGW/FERRULES

N/S R1081 PILOTORIFICE-NATURAL(SPP)

N/S R1089 PILOTORIFICE-PROPANE (SPP)

N/S R1233 PILOTORIFICE-NATURAL(IP)

N/S R3265 PILOTORIFICE-PROPANE (IP)

N/S R3172 WIREHARNESS(SPP)

N/S R3173 WIREHARNESS(IP)

N/S R1587C VENTSAFETYWIREASSEMBLY

N/S-NOTSHOWN

INDEX

NO.

PART

NO.

DESCRIPTION

37134-6-0520 Page 17

37134-6-0520Page 18

To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.com. To provide

warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with

thereplace.

To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below. This list

changesfromtimetotime.Forthecurrentlist,pleaseclickontheMasterPartsbuttonatwww.empirecomfort.com.

PleaseNOTICE:MasterPartsDistributorsareindependentbusinessesthatstockthemostcommonlyorderedOriginalEquipment

repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems.

MASTER PARTS DISTRIBUTOR LIST

Parts Not Under Warranty

Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distribu-

tors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the

service person/dealer.

Warranty Parts

Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for

warranty parts.

AllpartslistedinthePartsListhaveaPartNumber.Whenorderingparts,rstobtaintheModelNumberandSerialNumberfromthe

nameplateonyourequipment.ThendeterminethePartNumber(nottheIndexNumber)andtheDescriptionofeachpartfromthefol-

lowing illustration and part list. Be sure to give all this information . . .

FireplaceModelNumber Part Description

FireplaceSerialNumber  PartNumber

TypeofGas(PropaneorNatural)

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.

Shipmentscontingentuponstrikes,resandallcausesbeyondourcontrol.

HOW TO ORDER REPAIR PARTS

Dey Distributing

1401WillowLakeBoulevard

VadnaisHeights,MN55101

Phone: 651-490-9191

Toll Free:800-397-1339

Website: www.deydistributing.com

Parts: Heater, Hearth and Grills

F. W. Webb Company

200 Locust Street

Hartford, CT 06114

Phone:860-722-2433

Toll Free: 800-243-9360

Fax: 860-293-0479

Toll Free Fax:800-274-2004

Websites: www.fwwebb.com & www.victormfg.com

Parts: Heater, Hearth and Grills

East Coast Energy Products

10 East Route 36

WestLongBranch,NJ07764

Phone: 732-870-8809

Toll Free:800-755-8809

Fax: 732-870-8811

Website: www.eastcoastenergy.com

Parts: Heater, Hearth and Grills

37134-6-0520 Page 19

WARRANTY

Empire Comfort Systems Inc. warranties this space heating product to be free from defects at the time of purchase and for the periods

speciedbelow.Spaceheatingproductsmustbeinstalledbyaqualiedtechnicianandmustbemaintainedandoperatedsafely,in

accordance with the instructions in the owner’s manual. This warranty applies to the original purchaser only and is not transferable. All

warrantyrepairsmustbeaccomplishedbyaqualiedgasappliancetechnician.

Limited Ten-Year Parts Warranty – Combustion Chamber

 Empirepromisestotheownerthatifthecombustionchamber(seepartslist)failsbecauseofdefectiveworkmanshipor

material with ten years from the date of purchase, Empire will repair or replace at Empire’s option.

Limited One-Year Parts Warranty – Remote Controls, Accessories, and Parts

 Shouldanyremotecontrol,accessory,orotherpartfailbecauseofdefectiveworkmanshipwithinoneyearfromthedateof

purchase, Empire will repair or replace at Empire’s option.

Duties Of The Owner

 Theappliancemustbeinstalledbyaqualiedinstallerandoperatedinaccordancewiththeinstructionsfurnishedwiththe

 appliance.Abillofsale,cancelledcheck,orpaymentrecordshouldbekepttoverifypurchasedateandestablishwarranty

period. Ready access to the appliance for service.

What Is Not Covered

Damages that might result from the use, misuse, or improper installation of this appliance.

Travel, diagnostic costs and freight charges on warranted parts to and from the factory.

 Claimsthatdonotinvolvedefectiveworkmanshipormaterials.

Unauthorized service or parts replacements.

Removal and reinstallation cost.

 Inoperableduetoimproperorlackofmaintenance.

How To Get Service

 Tomakeaclaimunderthiswarranty,pleasehaveyourreceiptavailableandcontactyourinstallingdealer.Providethedealer

 withthemodelnumber,serialnumber,typeofgas,andpurchaseverication.Theinstallingdealerisresponsibleforproviding

 serviceandwillcontactthefactorytoinitiateanywarrantedpartsreplacements.Empirewillmakereplacementpartsavailable

at the factory. Shipping expenses are not covered.

If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations Department,

 EmpireComfortSystemsInc.,POBox529,Belleville,Illinois62222,orsendane-mailto[email protected]with

“Consumer Relations” in the subject line.

Your Rights Under State Law

 Thiswarrantygivesyourspeciclegalrights,andyoumayalsohaveotherrights,whichvaryfromstatetostate.

37134-6-0520Page 20

www.empirecomfort.com

Empire Comfort Systems Inc.

Belleville, IL

If you have a general question

aboutourproducts,pleasee-mail

usat[email protected].

If you have a service or repair

question, please contact your dealer.

La page charge ...

Empire Heating Systems Vented Counterflow Wall Furnace (FAW40) Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: Vented Counterflow Wall Furnace (FAW40)

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

FAW40

Télécharger le PDF

rapport

dans d''autres langues

English: Empire Heating Systems Vented Counterflow Wall Furnace (FAW40) Owner's manual

Empire Heating Systems Vented Counterflow Wall Furnace (FAW40) Le manuel du propriétaire

Ce manuel convient également à

Empire Heating Systems Vented Counterflow Wall Furnace (FAW40) Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents