Jenn-Air Air Cleaner air filter Manuel utilisateur

JENN-AIR

®

ELECTRIC SMOOTHTOP

DOWNDRAFT SLIDE-IN RANGE

Important Safety Instructions .....................................1-3

Ducting Information........................................................... 4

Care & Cleaning ..............................................................4-7

Maintenance.....................................................................7-8

Troubleshooting ........................................................... 9-10

Surface Cooking......................................................... 11-14

Oven Cooking..............................................................15-21

Options .......................................................................... 22-26

Favorites ...............................................................................27

Setup .............................................................................. 28-30

Accessories .........................................................................30

Warranty & Service...........................................................31

Guide d’utilisation et d’entretien .................................32

Guía de uso y cuidado ....................................................64

USE & CARE

GUIDE

TABLE OF CONTENTS

®

8113P528-60 10/20/05, 11:56 AM1

1

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this guide for future

reference. Keep sales receipt and/or cancelled check as

proof of purchase.

Model Number __________________________________

Serial Number __________________________________

Date of Purchase ________________________________

If you have questions, call:

Jenn-Air Customer Assistance

1-800-JENNAIR (1-800-536-6247)

1-800-688-2080 (U.S. TTY for hearing or speech impaired)

(Mon.-Fri., 8 am-8 pm Eastern Time)

Internet: http://www.jennair.com

In our continuing effort to improve the quality and

performance of our cooking products, it may be necessary

to make changes to the appliance without revising this

guide.

For service information, see page 31.

IMPORTANT SAFETY

INSTRUCTIONS

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing,

maintaining, or operating the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION – Hazards or unsafe practices which

COULD result in minor personal injury.

WARNING

CAUTION

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service,

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

To Prevent Fire or Smoke

Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials. Flammable materials should not

be stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot.

To prevent grease fires, do not let cooking grease or

other flammable materials accumulate in or near the

appliance.

General Instructions

WARNING: To reduce risk of

tipping of the appliance from

abnormal usage or by excessive loading of the

oven door, the appliance must be secured by a

properly installed anti-tip device.

WARNING

• ALL RANGES CAN TIP AND

CAUSE INJURIES TO PERSONS

• INSTALL ANTI-TIP DEVICE

PACKED WITH RANGE

• FOLLOW ALL INSTALLATION

INSTRUCTIONS

or replace any part of your appliance unless it is

specifically recommended in this guide. All other

servicing should be referred to a qualified servicer.

Always disconnect power to appliance before servicing.

In Case of Fire

Turn off appliance and ventilating hood to avoid

spreading the flame. Extinguish flame, then turn on

hood to remove smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

8113P528-60 10/20/05, 11:56 AM2

2

CAUTION

NEVER store items of interest to children in cabinets

above an appliance or on backguard of a range.

Children climbing on the appliance door to reach items

could be seriously injured.

WARNING

NEVER use appliance as a step to reach cabinets above.

Misuse of appliance door, such as stepping, leaning or

sitting on the door, may result in possible tipping of the

appliance, breakage of the door and serious injuries.

NEVER leave children alone or unsupervised near the

appliance when it is in use or is still hot. Children

should never be allowed to sit or stand on any part of

the appliance as they could be injured or burned.

Children must be taught that the appliance and utensils

in it can be hot. Let hot utensils cool in a safe place, out

of reach of small children. Children should be taught

that an appliance is not a toy. Children should not be

allowed to play with controls or other parts of the

appliance.

About Your Appliance

To prevent potential hazard to the user and damage to

the appliance, do not use appliance as a space heater to

heat or warm a room. Also, do not use the oven as a

storage area for food or cooking utensils.

Do not obstruct the flow of air by blocking theoven vent.

DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN. Heating elements may be hot even

though they are dark in color. Interior surfaces of any

oven become hot enough to cause burns. During and

after use, do not touch, or let clothing or other flammable

materials contact heating elements or interior surfaces of

oven until they have had sufficient time to cool. Other

surfaces of the appliance may become hot enough to

cause burns – among these surfaces are: oven vent

opening and surface near this opening, oven door and

window of oven door.

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect

power to the appliance before removing bulb to avoid

electrical shock.

NEVER use aluminum foil to cover an oven rack or oven

bottom. Misuse could result in risk of electric shock, fire,

or damage to the appliance. Use foil only as directed in

this guide.

Cooking Safety

Never heat an unopened food container in the oven.

Pressure build-up may cause container to burst

resulting in serious personal injury or damage to the

appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes

should never be used as potholders because they can

trail across hot elements and ignite or get caught on

appliance parts.

Wear proper apparel. Loose fitting or long hanging-

sleeved apparel should not be worn while cooking.

Clothing may ignite and cause burns if garment comes

in contact with heating elements.

Always place oven racks in the desired positions while

oven is cool. Slide oven rack out to add or remove food,

using dry, sturdy potholders. Always avoid reaching into

the oven to add or remove food. If a rack must be

moved while hot, use a dry potholder. Do not let

potholder contact hot element in oven.

Use racks only in the oven in which they were shipped/

purchased.

Use care when opening the oven door. Let hot air or

steam escape before removing or replacing food.

PREPARED FOOD WARNING: Follow food

manufacturer’s instructions. If a plastic frozen food

container and/or its cover distorts, warps, or is otherwise

damaged during cooking, immediately discard the food

and its container. The food could be contaminated.

Do not allow aluminum foil or meat probe to contact

heating element.

Always turn off all controls when cooking is completed.

• Oven: Smother fire or flame by closing the oven door.

Do not use water on grease fires. Use baking soda, a

dry chemical or foam-type extinguisher to smother fire

or flame.

Child Safety

Utensil Safety

Follow the manufacturer’s directions when using oven

cooking bags.

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices

or accessories that are not specifically recommended in

this guide. Do not use add-on oven convection systems.

The use of devices or accessories that are not expressly

Cont.

8113P528-60 10/20/05, 11:56 AM3

3

Cleaning Safety

Clean cooktop with caution. Turn off all controls and wait

for appliance parts to cool before touching or cleaning.

Use care to avoid steam burns if a wet sponge or cloth is

used to wipe spills on a hot surface. Some cleaners can

produce noxious fumes if applied to a hot surface.

Clean only parts listed in this guide.

Self-Clean Oven

Do not clean door gasket. The door gasket is essential

for a good seal. Care should be taken not to rub,

damage, or move the gasket.

Do not use oven cleaners or oven liners of any kind in or

around any part of the self-clean oven.

Important Safety Notice

and Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances

known to the State of California to cause cancer or

reproductive harm, and requires businesses to warn

customers of potential exposures to such substances.

Users of this appliance are hereby warned that when the

oven is engaged in the self-clean cycle, there may be

some low-level exposure to some of the listed sub-

stances, including carbon monoxide. Exposure to these

substances can be minimized by properly venting the

oven to the outdoors by opening the windows and/or

door in the room where the appliance is located during

the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS: Never

keep pet birds in the kitchen or in rooms where the

fumes from the kitchen could reach. Birds have a very

sensitive respiratory system. Fumes released during an

oven self-cleaning cycle may be harmful or fatal to birds.

Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

recommended in this guide can create serious safety

hazards, result in performance problems, and reduce the

life of the components of the appliance.

If pan is smaller than element, a portion of the element

will be exposed to direct contact and could ignite

clothing or potholder.

Only certain types of glass, glass/ceramic, ceramic,

earthenware, or other glazed utensils are suitable for

cooktop or oven service without breaking due to the

sudden change in temperature. Follow utensil

manufacturer’s instructions when using glass.

Turn pan handle toward center of cooktop, not out into

the room or over another surface element. This reduces

the risk of burns, ignition of flammable materials, or

spillage if pan is accidently bumped or reached by small

children.

Cooktop

NEVER leave surface units unattended, especially when

using high heat. An unattended boilover could cause

smoking and a greasy spillover can cause a fire.

This appliance is equipped with different size surface

elements. Select pans with flat bottoms large enough to

cover element. Fitting pan size to element will improve

cooking efficiency.

GLASS-CERAMIC SURFACE: NEVER cook on broken

cooktop. If cooktop should break, cleaning solutions and

spillovers may penetrate the broken cooktop and create

a risk of electric shock. Contact a qualified technician

immediately.

Deep Fat Fryers

Use extreme caution when moving the grease pan or

disposing of hot grease. Allow grease to cool before

attempting to move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease

or other flammable materials from accumulating on hood

or filter and to avoid grease fires.

When flaming foods under the hood, turn the fan on.

Save These Instructions for Future Reference

CAUTION

Before self-cleaning the oven, remove the oven racks,

broiler pan, food and any other utensils. Wipe

spillovers to prevent excessive smoke and flare-ups.

8113P528-60 10/20/05, 11:56 AM4

4

Jenn-Air’s ventilation system is designed to capture both

cooking fumes and smoke from the cooktop surface. If the

system does not, here are some ducting installation situations

to check:

• 6” diameter round or 3

1

/

4

” x 10” rectangular ducting should

be used for duct lengths 10’-60’.

• There should be a minimum clearance of 6” for cooktop

installed near a side wall.

If there is not an obvious improper installation, there may be a

concealed problem such as a pinched joint, obstruction in the

pipe, etc. Installation is the responsibility of the

installer and questions should be addressed

first by the installer. The installer should very

carefully check the ducting installation instruc-

tions.

• Use the Flow Tester Card provided with your

appliance to check the air flow.

DUCTING INFORMATION

• No more than three 90° elbows should be used. Distance

between elbows should be at least 18”.

• Recommended Jenn-Air wall cap MUST be used. Make

sure damper moves freely when ventilation system is

operating.

Important: 5” diameter round ducting may be used if the

duct length is 10’ or less.

CARE & CLEANING

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

Self-Clean Oven

CAUTION

• It is normal for parts of the oven to become hot during a

self-clean cycle.

• To prevent damage to oven door, do not attempt to open

the door when LOCK is displayed.

• Avoid touching door, window or oven vent area during a

clean cycle.

• Do not use commercial oven cleaners on the oven finish

or around any part of the oven. They will damage the

finish or parts.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

It is normal for flare-ups, smoking, or flaming to occur during

cleaning if the oven is heavily soiled. It is better to clean the

oven regularly rather than to wait until there is a heavy build-

up of soil in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

easily after a self-clean cycle if they are not removed.

Important: Remove the air grille from the cooking surface

before self-cleaning.

3. Clean oven frame, door frame, area

outside of gasket, and around the

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. (The gasket is the seal around the oven door and

window.)

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket is designed to seal in heat

during the clean cycle.

5. Wipe up excess grease or spill-overs from the oven

bottom. This prevents excessive smoking, flare-ups or

flaming during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

discolor if acidic or sugary spills are not wiped up before a

self-clean cycle.

Cont.

To set Self-Clean:

1. Press Clean pad.

2. REMOVE RACKS will be displayed. Remove the racks.

1. Turn off the oven light before cleaning. The oven light may

burn out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide

8113P528-60 10/20/05, 11:56 AM5

5

3. Select CONTINUE using the Quickset pad. The Quickset

pads are located on either side of the control panel

display.

4. Set LIGHT soil level by entering 200 using the number

pads for two hours of cleaning time. Select MEDIUM soil

level using the Quickset pads.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

To Delay a Self-Clean Cycle:

1. Press Clean pad.

2. REMOVE RACKS will be displayed.

Remove the racks.

3. Select CONTINUE using the Quickset pad.

4. Set LIGHT soil level by entering 200 using the number

pads for two hours of cleaning time. Select MEDIUM soil

level using the Quickset pads.

OR

Select HEAVY for a heavily soiled oven and four hours of

cleaning time.

5. The door will lock. CLEAN, TIME, LOCKED and the

cleaning time countdown will be displayed

6. After door locks, press the More Options pad.

7. Select DELAY using the Quickset pad.

Notes:

• If the oven door is left open, CLOSE DOOR will appear in

the display until the door is closed.

• If more than 30 seconds elapse between pressing the

Clean pad and pressing a number pad, the program will

automatically return to the previous display.

• The oven door will be damaged if it is forced to open

during cleaning or cooling process.

• The first few times the oven is cleaned, some smoke and

odor may be detected. This is normal and will lessen or

disappear with use. If the oven is heavily soiled, or if the

broiler pan was accidently left in the oven, excessive

smoke and odor may occur.

• As the oven heats and cools, you may hear sounds of

metal parts expanding and contracting. This is normal

and will not damage your appliance.

8. Select the number of hours you want to delay the start of the

self-clean cycle.

9. The delay time and cleaning time will be displayed.

After Self-Cleaning

About one hour after the end of the clean cycle, the lock

will disengage and OVEN COOLING will go off in the

display. At this point, the door can be opened.

Some soil may leave a light gray, powdery ash which can be

removed with a damp cloth. If soil remains, it indicates that

the clean cycle was not long enough. The soil will be removed

during the next clean cycle.

If the oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and embossed rack

supports with a small amount of vegetable oil to restore ease

of movement.

A white discoloration may appear after cleaning if acidic or

sugary foods were not wiped up before the clean cycle. This is

normal and will NOT affect performance.

5. CLEAN, TIME, LOCKED and the cleaning time countdown

will be displayed while the oven is cleaning. OVEN

COOLING will appear in the display when the cleaning

time has been completed and the oven is still locked.

Important: The door lock will disengage approximately one

hour after the cleaning time is completed. OVEN COOLING

will go off in the display when the oven door has unlocked.

8113P528-60 10/20/05, 11:56 AM6

6

Cont.

PART PROCEDURE

CAUTION

Cleaning Procedures

• Be sure appliance is off and all parts are cool before handling

or cleaning. This is to avoid damage and possible burns.

• To prevent staining or discoloration, clean appliance after each use.

• If a part is removed, be sure it is correctly replaced.

Control Panel • To activate control lock for cleaning, see Locking the Control, page 16.

• Wipe with damp cloth. Dry thoroughly.

• Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on control pads and

display area.

• Do not use other cleaning sprays, abrasive cleaners or large amounts of water on the panel.

Control Knobs • Remove knobs in the OFF position by pulling forward.

• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

• Turn on each element to be sure the knobs have been correctly replaced.

Cooktop – Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia.

Glass-Ceramic Important: Call an authorized servicer if the glass-ceramic top should crack, break or if metal or

aluminum foil should melt on the cooktop.

• Allow the cooktop to cool before cleaning.

• General – Clean cooktop after each use, or when needed, with a damp paper towel and Cooktop Cleaning

Creme* (Part No. 20000001)**. Then buff with a clean, dry cloth.

Important: Permanent stains will develop if soil is allowed to cook on by repeatedly using the cooktop when

soiled.

• Heavy Soils or Metal Marks – Dampen a “scratchless” or “never scratch” scrubber sponge. Apply

Cooktop Cleaning Creme* and scrub to remove as much soil as possible. Apply a thin layer of the creme over

the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3 hours for very heavy soil). Keep

moist by covering the paper towel with plastic wrap. Scrub again, then buff with a clean, dry cloth.

Important: Only use a CLEAN, DAMP “scratchless” pad that is safe for non-stick cookware. The pattern and

glass will be damaged if the pad is not damp, if the pad is soiled, or if another type of pad is used.

• Burned-On or Crusty Soils – Scrub with a “scratchless” or “never scratch” scouring pad and

Cooktop Cleaning Creme*.

Important: Hold a razor blade scraper at 30

°

angle and scrape any remaining soil. Then, clean as described

above. Do not use the razor blade for daily cleaning as it may wear the pattern on the glass.

• Melted Sugar or Plastic – Immediately turn element to LOW and scrape sugar or plastic

from hot surface to a cool area. Then turn element OFF and allow to cool. Clean residue

with razor blade scraper and Cooktop Cleaning Creme*.

Oven Window • Avoid using excessive amounts of water which may seep under or behind glass causing staining.

and Door - • Wash with soap and water. Rinse with clear water and dry. Glass cleaner can be used if sprayed on a

Glass cloth first.

• Do not use abrasive materials such as scouring pads, steel wool or powdered cleaners as they will

scratch glass.

Oven Interior • Follow instructions on pages 4-5 to set a self-clean cycle.

Oven Racks • Clean with soapy water.

• Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

• Racks will permanently discolor and may not slide smoothly if left in the oven during a self-clean operation.

If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease

of movement, then wipe off excess oil.

* Brand names are registered trademarks of the

respective manufacturers.

** To order call 1-800-JENNAIR (1-800-536-6247).

8113P528-60 10/20/05, 11:56 AM7

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

** To order direct, call 1-800-JENNAIR (1-800-536-6247).

PART PROCEDURE

Stainless Steel • DO NOT USE ANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH.

(select models) • DO NOT USE ABRASIVE OR ORANGE CLEANERS.

• ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

• Daily Cleaning/Light Soil –– Wipe with one of the following - soapy water, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse

and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray* (Part No.

20000008)**.

• Moderate/Heavy Soil –– Wipe with one of the following - Bon Ami, Smart Cleanser, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi-

purpose Scotch-Brite* pad; rub evenly with the grain. Rinse and dry. To restore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

• Discoloration –– Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse

immediately and dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

7

MAINTENANCE

CAUTION

Oven Door

NEVER place excessive weight on or stand on an open

oven door. This could cause the range to tip over, break

the door, or injure the user.

• NEVER attempt to open or close door or operate oven until

door is properly replaced.

• NEVER place fingers between hinge and front oven frame.

Hinge arms are spring mounted. If accidentally hit, the

hinge will slam shut against oven frame and could injure

your fingers.

To remove:

1. When cool, open the oven door

to the broil stop position

(opened about four inches).

2. Grasp door at each side. Do not

use the door handle to lift door.

3. Lift up evenly until door clears

hinge arms.

To replace:

1. Grasp door at each side.

2. Align slots in the door with the hinge arms on the range.

3. Slide the door down onto the hinge arms until the door is

completely seated on the hinges. Push down on the top

corners of the door to completely seat door on hinges.

Door should not appear crooked.

Important: The oven door on a new range may feel “spongy”

when it is closed. This is normal and will decrease with use.

Oven Window

To protect the oven door window:

1. Do not use abrasive cleaning agents such as steel wool

scouring pads or powdered cleansers as they may scratch

the glass.

2. Do not hit the glass with pots, pans, furniture, toys, or

other objects.

3. Do not close the oven door until the oven racks are in

place.

Scratching, hitting, jarring or stressing the glass may weaken

its structure causing an increased risk of breakage at a later

date.

8113P528-60 10/20/05, 11:56 AM8

8

Leveling Legs

ANTI-TIP BRACKET

LEVELING LEG

Be sure the anti-tip bracket secures one of the rear

leveling legs to the floor. This bracket prevents the range

from accidentally tipping.

Be sure the range is leveled when installed. If

the range is not level, turn the leveling legs,

located at each corner of the range, until range

is level.

ANTI-TIP BRACKET

LEVELING LEG

CAUTION

To assure the proper replacement bulb is used, order bulb

from Jenn-Air. Call 1-800-JENNAIR (1-800-536-6247), ask for

part number 74004458 - halogen bulb.

To Replace Oven Light Bulb:

1. Disconnect power to the wall oven.

2. When oven is cool, use fingertips to grasp edge of bulb

cover. Pull out and remove.

3. Carefully remove old bulb by pulling straight out of

ceramic base.

4. To avoid damaging or decreasing the life of the new bulb,

do not touch the bulb with bare hands or fingers. Hold

with a dry cloth or paper towel. Push new bulb prongs

straight into small holes of ceramic base.

5. Replace bulb cover by snapping into place.

6. Reconnect power to the oven. Reset clock.

Oven Light

CAUTION

• Disconnect power to oven before replacing light bulb.

• Allow oven to cool before replacing light bulb.

• Make sure bulb cover and bulb are cool before touching.

8113P528-60 10/20/05, 11:56 AM9

9

TROUBLESHOOTING

For most concerns, try these first. • Check if oven controls have been properly set.

• Check to be sure plug is securely inserted into receptacle.

• Check or re-set circuit breaker. Check or replace fuse.

• Check power supply.

Part or all of appliance does not • Check if surface and/or oven controls have been properly set. See pgs. 11, 12 & 17.

work. • Check if oven door is unlocked after self-clean cycle. See pg. 5.

• Check if oven is set for a delayed cook or clean program. See pgs. 17 & 5.

• Check if Control Lock is activated. See pg. 16.

• Check if control is in Sabbath Mode. See pg. 29.

Clock, indicator words, and/or • Oven may be set for a Cook & Hold or delay function.

lights operate but oven does • Control Lock may have been set. See pg. 16.

not heat.

Baking results are not as • Make sure the oven vent has not been blocked. See pg. 21 for location.

expected or differ from • Check to make sure range is level.

previous oven. • Temperatures often vary between a new oven and an old one. As ovens age, the oven

temperature often “drifts” and may become hotter or cooler. See pg. 29 for

instructions on adjusting the oven temperature. Important: It is not recommended

to adjust the temperature if only one or two recipes are in question.

Food is not broiling properly or • Check oven rack positions. Food may be too close to element.

smokes excessively. • Broil element was not preheated.

• Aluminum foil was incorrectly used. Never line the broiler insert with foil.

• Oven door was closed during broiling. Leave the door open to the first stop position

(about 4 inches).

• Trim excess fat from meat before broiling.

• A soiled broiler pan was used.

• Voltage in house may be low.

Oven will not self-clean. • Check to make sure the cycle is not set for a delayed start. See pg. 5.

• Check if door is closed.

• Check if control is in Sabbath Mode. See pg. 29.

• Oven may be over 400° F. Oven temperature must be below 400° F to program a

clean cycle.

Oven did not clean properly. • Longer cleaning time may be needed.

• Excessive spillovers, especially sugary and/or acidic foods, were not removed prior

to the self-clean cycle.

Oven door will not unlock after • Oven interior is still hot. Allow about one hour for the oven to cool after the

self-clean cycle. completion of a self-clean cycle. The door can be opened when the LOCK indicator

word is not displayed.

• The control and door may be locked. See pg. 16.

There are no beeps and • Oven may be in Sabbath Mode. See pg. 29.

no display.

PROBLEM SOLUTION

8113P528-60 10/20/05, 11:56 AM10

10

Smoothtop surface 1. Tiny scratches or abrasions.

shows wear. • Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans

across top. Make sure pan bottom is not rough. Use the recommended cleaning

agents. See page 6.

2. Metal marks.

• Do not slide metal pans across top. When cool, clean with Cooktop Cleaning Creme.

See page 6.

3. Brown streaks and specks.

• Remove spills promptly. Never wipe with a soiled cloth or sponge. Make sure cooktop

and pan bottom are clean.

4. Areas with a metallic sheen.

• Mineral deposits from water and food. Use recommended cleaning agents. See page 6.

5. Pitting or flaking.

• Remove sugary boilovers promptly. See page 6.

Moisture collects on oven • This is normal when cooking foods high in moisture.

window or steam comes from • Excessive moisture was used when cleaning the window.

oven vent.

There is a strong odor or light • This is normal for a new range and will disappear after a few uses. Initiating a clean

smoke when oven is turned on. cycle will “burn off” the odors more quickly.

• Turning on a ventilation fan will help remove the smoke and/or odor.

• Excessive food soils on the oven bottom. Use a self-clean cycle.

Cooktop does not get • Surface controls may not be set properly.

hot enough. • Voltage to house may be low.

Ventilation system is not • Check on cross ventilation in room or make up air.

capturing smoke efficiently. • Outside wall cap may be trapped shut.

• Range may be improperly installed; check ducting information. See pg. 4.

• Air filter may be improperly installed. See pg. 14.

Fault Codes • The oven may detect a fault during programming or during operation. If a fault is

detected, the message FAULT DETECTED - PRESS POWER TO CLEAR or FAULT

DETECTED - PRESS ENTER TO TRY AGAIN may appear. Follow directions in the display.

If the fault reappears or does not clear, call an authorized servicer or the toll-free number

in the display.

• If the same operation is attempted before having the wall oven repaired, the message

FEATURE NOT AVAILABLE will appear. The feature will remain inoperable until service

is obtained.

• If the oven is heavily soiled, excessive flareups may result in a fault code during cleaning.

Press the CANCEL pad and allow the oven to cool completely, wipe out excess soil, then

reset the clean cycle. If the fault code reappears, contact an authorized servicer.

Noises may be heard. • The oven makes several low-level noises. You may hear the oven relays as they go on

and off. This is normal.

• As the oven heats and cools, you may hear sounds of metal parts expanding and

contracting. This is normal and will not damage your appliance.

SAb flashing and then • Oven is in Sabbath Mode. To cancel, press and hold the Setup pad for five

displayed continuously. seconds.

PROBLEM SOLUTION

8113P528-60 10/20/05, 11:56 AM11

11

SURFACE COOKING

Surface Controls

Use to turn on the surface elements. An infinite choice of

heat settings is available from Low to High. The knobs can

be set on or between any of the settings.

BEFORE COOKING

• Always place a pan on the surface unit before you turn it

on. To prevent damage to range, never operate surface

unit without a pan in place.

• NEVER use the cooktop as a storage area for food or

cookware.

DURING COOKING

• Be sure you know which knob controls which surface

unit. Make sure you turned on the correct surface unit.

• Begin cooking on a higher heat setting then reduce to a

lower setting to complete the operation. Never use a

high heat setting for extended cooking.

• NEVER allow a pan to boil dry. This could damage the

pan and the appliance.

• NEVER touch cooktop until it has cooled. Expect some

parts of the cooktop, especially around the surface units,

to become warm or hot during cooking. Use potholders

to protect hands.

CAUTION

AFTER COOKING

• Make sure surface unit is turned off.

• Clean up messy spills as soon as possible.

OTHER TIPS

• If cabinet storage is provided directly above cooking

surface, limit it to items that are infrequently used and

can be safely stored in an area subjected to heat.

Temperatures may be unsafe for items such as volatile

liquids, cleaners or aerosol sprays.

• NEVER leave any items, especially plastic items, on the

cooktop. The hot air from the vent may ignite flammable

items, melt or soften plastics, or increase pressure in

closed containers, causing them to burst.

• NEVER allow aluminum foil, meat probes or any other

metal object, other than a pan on a surface element, to

contact heating elements.

• NEVER store heavy items above the cooktop that could fall

and damage it.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

• The control panel is marked to identify which

element the knob controls. For example, the

graphic at right indicates right front element.

3. There is an element indicator light on the control panel.

When any surface control knob is turned on, the light will

turn on. The light will turn off when all the surface

elements are turned off.

When a control is turned on, a glow can be seen through

the smoothtop surface. The element will cycle on and off

to maintain the preset heat setting, even on High.

4. After cooking, turn knob to OFF. Remove pan.

Dual Element

The cooking surface is equipped with two

dual elements located in the right front

and left rear positions. To operate, push

in on the control knob and turn to the

right to control the small element, or

push in and turn to the left to control the

large element.

Flex-Choice

TM

Elements (select models)

The Flex-Choice

TM

elements are fully

functioning elements that provide an

ultra low Melt heat setting for melting

chocolate and butter. They are located

in the left front and right rear positions.

The Melt setting is located between

3 and OFF. Heat settings outside of this

area function as a normal element, with 3

(Low) to High settings.

Important: When using the normal settings for preparing

foods, it may take a few minutes for the cooking area to cool

to the Warm heat setting.

Custom Control (select models)

The Custom Control Dual Element offers

two element sizes and is located in the

right front position. This element uses

an electronic sensor to constantly

monitor and adjust heat output for

precise and consistent temperature

control.

8113P528-60 10/20/05, 11:56 AM12

12

Medium (5): Use to

maintain slow boil for

large amounts of liquids

and for most frying

operations.

Suggested Heat Settings

The size, type of cookware and cooking operation will affect

the heat setting.

Low (1): Use to keep

foods warm and melt

chocolate and butter.

High (9): Use to bring

liquid to a boil. Always

reduce setting to a lower

heat when liquids begin to

boil or foods begin to cook.

Med. Low (3):

Use to con-

tinue cooking

covered foods

or steam foods.

Med. High (7): Use to

brown meat, heat oil for

deep fat frying or

sauteing. Maintain fast

boil for large amounts

of liquids.

Notes:

• Cooktop may emit light smoke and odor the first few

times the cooktop is used. This is normal.

• Smoothtop cooktops retain heat for a period of time

after the element is turned off. Turn the elements off

a few minutes before food is completely cooked and use

the retained heat to complete cooking. When the hot

surface light turns off, the cooking area will be cool

enough to touch. Because of the way they retain heat, the

smoothtop elements will not respond to changes in

settings as quickly as coil elements.

• In the event of a potential boilover, remove the pan from

the cooking surface.

• Never attempt to lift the cooktop.

• The smoothtop surface may appear discolored when it is

hot. This is normal and will disappear when the surface

cools.

Smoothtop Surface

Cooking Areas

The cooking areas on your range are identified by permanent

patterns on the smoothtop surface. For most efficient cooking,

fit the pan size to the element size.

Pans should not extend more than

1

/

2

to 1-inch beyond

the cooking area.

When a control is turned on, a glow can be seen through the

smoothtop surface. The element will cycle on and off to

maintain the preset heat setting, even on High.

For more information on cookware, refer to Cookware

Recommendations on page 13.

Hot Surface Indicator Lights

The Hot Surface indicator lights are located next to the

elements. These lights indicate when the adjacent cooking

SINGLE ELEMENT

FLEX-CHOICE

TM

ELEMENT

(SELECT MODELS)

CUSTOM ELEMENT

(SELECT MODELS)

Tips to Protect the

Smoothtop Surface

Cleaning (see page 6 for more information)

• Before first use, clean the cooktop.

• Clean your cooktop daily or after each use. This will keep

your cooktop looking good and can prevent damage.

• If a spillover occurs while cooking, immediately clean the

spill from the cooking area while it is hot to prevent a tough

cleaning chore later. Using extreme care, wipe spill with a

clean, dry towel.

• Do not allow spills to remain on the cooking area or the

cooktop trim for a long period of time.

• Never use abrasive cleansing powders or scouring pads

which will scratch the cooktop.

• Never use chlorine bleach, ammonia or other cleansers not

specifically recommended for use on glass-ceramic.

To Prevent Marks & Scratches

• Do not use glass pans. They may scratch the surface.

• Never place a trivet or wok ring between the surface and

pan. These items can mark or etch the top.

• Do not slide aluminum pans across a hot surface. The pans

may leave marks which need to be removed promptly. (See

Cleaning, page 6.)

DUAL

ELEMENT

area is hot to the touch even after the control has been turned

off. The red light will remain on until the surface has

cooled.

Cont.

8113P528-60 10/20/05, 11:56 AM13

13

• Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

• To prevent scratching or damage to the glass-ceramic top,

do not leave sugar, salt or fats on the cooking area. Wipe

the cooktop surface with a clean cloth or paper towel

before using.

• Never slide heavy metal pans across the surface since

these may scratch.

To Prevent Stains

• Never use a soiled dish cloth or sponge to clean the

cooktop surface. A film will remain which may cause stains

on the cooking surface after the area is heated.

• Continuously cooking on a soiled surface may/will result in

a permanent stain.

To Prevent Other Damage

• Do not allow plastic, sugar or foods with high sugar

content to melt onto the hot cooktop. Should this happen,

clean immediately. (See Cleaning, page 6.)

• Never let a pan boil dry as this will damage the surface and

pan.

• Never use cooktop as a work surface or cutting board.

• Never cook food directly on the surface.

• Do not use a small pan on a large element. Not only does

this waste energy, but it can also result in spillovers burning

onto the cooking area which requires extra cleaning.

• Do not use non-flat specialty items that are oversized or

uneven such as round-bottom woks, rippled bottom and/or

oversized canners and griddles.

• Do not use foil or foil-type containers. Foil may melt onto

the glass. If metal melts on the cooktop, do not use. Call an

authorized servicer.

Cookware Recommendations

Select Avoid

Flat, smooth-bottom Pans with grooved or warped bottoms.

pans. Pans with uneven bottoms do not cook

efficiently and sometimes may not

boil liquid.

Heavy-gauge pans. Very thin-gauge metal or glass pans.

Pans that are the Pans smaller or larger than the

same size as the element by 1 inch.

element.

Secure handles. Cookware with loose or broken handles.

Heavy handles that tilt the pan.

Tight-fitting lids. Loose-fitting lids.

Flat-bottom woks. Woks with a ring-stand bottom.

Using the right cookware can prevent many problems, such

as food taking longer to cook or achieving inconsistent

results. Proper pans will reduce cooking times, use less

energy, and cook food more evenly.

Flat Pan Tests

To determine whether your pans are flat.

The Ruler Test:

1. Place a ruler across the bottom of the pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put 1 inch of water in the pan. Place on cooktop and turn

control to High.

2. Watch the formation of the bubbles as the water heats.

Uniform bubbles mean good performance, and uneven

bubbles indicate hot spots and uneven cooking.

Wok Cooking

Use Jenn-Air’s flat bottom wok (Model AO142) for optimum

results. Call 1-800-JENNAIR (1-800-536-6247) to order. The

wok has a non-stick finish, wood handles, cover, steaming

rack, rice paddles, cooking tips and recipes.

Canning and Oversize Cookware

All canners and large pots must have flat bottoms and

must be made from heavy-gauge materials. This is critical

on smoothtop surfaces. The base must not be more than

1 inch larger than the element.

When canners and pots do not meet these standards, cooking

times may be longer, and cooktops may be damaged.

Some canners are designed with smaller bases for use on

smoothtop surfaces.

When canning, use the High heat setting only until the

water comes to a boil or pressure is reached in the canner.

Reduce to the lowest heat setting that maintains the boil or

pressure. If the heat is not turned down, the cooktop may be

damaged.

8113P528-60 10/20/05, 11:56 AM14

14

Ventilation System

The built-in ventilation system removes cooking vapors, odors

and smoke from foods prepared on your cooktop and grill.

• To operate the ventilation

system manually, push the

Vent Fan pad located on the

electronic control. Push once

for Low, push again for High

and a third time to turn the

fan Off.

• The ventilation system will operate automatically when the

grill element is in use.

• The fan can be used to remove strong odors from the

kitchen, as when chopping onions near the fan.

Care and Cleaning of the

Ventilation System

• Air Grille: The air grille lifts off easily. Wipe clean or wash in

dishwasher or sink with mild household detergents. To

prevent scratching the surface, do not use abrasive

cleaners or scrubbing pads.

• Filter: Turn off ventilation system before removing. The filter

is a permanent type and should be cleaned when soiled.

Clean in sink with warm water and detergent or in

dishwasher.

➞

IMPORTANT: DO NOT OPERATE SYSTEM WITHOUT

FILTER. Filter should always be placed at an angle. As you

face the front of the range, the top of the filter should rest

against the left side of the vent opening. The bottom should

rest against the right side of the vent chamber at the

bottom. Important: If filter is flat against the fan wall,

ventilation effectiveness is reduced.

• Ventilation Chamber: This area, which houses the filter,

should be cleaned in the event of spills or whenever it

becomes coated with a film of grease. It can be cleaned with

paper towel, damp cloth, or sponge and mild household

detergent or cleanser.

Important: The oven vent is located under the right side of

the air grille. When using or cleaning the oven, hot and

moist air may be noticed in this area. The area near the vent

may become hot enough to cause burns. Be careful not to

spill anything into this vent. The air grille must be

removed before the self-clean cycle.

AIR FILTER

8113P528-60 10/20/05, 11:56 AM15

15

OVEN COOKING

A Rapid Preheat Use to decrease preheating time.

B Convect Use for convection baking and roasting.

C Bake Use for baking and roasting.

D Broil Use for broiling and top browning.

E TIMER 1 Sets timer.

F Display Displays oven functions, options and

window time of day.

G TIMER 2 Sets timer.

H Number Pads Use to enter time and temperature,

or to enter Favorites names.

I Favorites Use to access, program or save

baking cycles.

J More Options Use to access additional features.

K Clean Use to set self-clean cycle.

L Setup Use to view or change factory

default settings.

M Vent Fan Activates the ventilation fan on

the cooktop.

N Oven Light Use to turn the oven light on or off.

O CANCEL Cancels all operations except Timer,

Clock, Favorites, Setup and Vent Fan.

P Quickset pads Use to select options in display

window (next to display window

on both sides).

The control panel is designed for ease in programming. The display window shows options for each function and moves from step

to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake

operation.

A B C D E F G H

Control Panel

Quickset Pads

Quickset pads are located on each side of the display window

and are used to select the desired function or option in the

display window. To select the option or function, press the

Quickset pad next to the word.

Important: Four seconds after entering the function,

option, number or letter, the function will automatically be

entered. If more than 30 seconds elapse between steps in

programming, the function will be canceled and the

display will return to the previous display.

Clock

Setting the Clock:

1. Press the Setup pad.

2. Select CLOCK using the Quickset pads.

3. Select TIME.

4. Enter the time using the number pads.

5. Press Enter pad.

6. Select AM or PM in 12 hour mode. (For 24 hour clock, see

page 16.)

7. To exit the Setup mode, press Setup pad.

If you need to back out of a function or option in the display,

press the Back pad. When your programming is complete,

press the Enter pad or wait four seconds and the function will

start automatically.

Up arrows indicate additional screens with additional options.

Press the Quickset pads next to the arrows to scroll through

the display.

I J K L M N O P

8113P528-60 10/20/05, 11:56 AM16

16

Activating and canceling the clock/day

of week display:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DISABLE is displayed.

4. Select DISABLE.

5. Select OFF to turn the clock display off, or select ON to turn

the clock display on.

6. Select OFF to turn the day of the week display off. Select

ON to turn the weekday display on.

7. To exit the Setup mode, press Setup pad.

Entering the day of the week:

1. Press Setup pad.

2. Select CLOCK.

3. Press the arrow to scroll until DAY is displayed.

4. Use Quickset arrow to scroll through the days.

5. To exit the Setup mode, press Setup pad.

To set the clock for a 12 or 24 hour format:

The clock can be set to display time in either a 12 hour or 24

hour format.

1. Press the Setup pad.

2. Select CLOCK.

3. Use the arrow to scroll to the next screen.

4. Select 12/24 HOUR.

5. Select 12 HR or 24 HR.

6. To exit Setup mode, press Setup pad.

Timers

Setting the Timers (Timer 1 or Timer 2):

1. Press TIMER 1 or TIMER 2 pad.

2. Press one of the displayed times using the

Quickset pads, or press the number pads to

enter the desired time.

Important: Each press of the displayed time choices adds

additional time. For example, pressing “10 MIN” three

times provides 30 minutes on the timer (0:30).

3. Press Enter pad.

Changing the amount of time entered once the

Timer starts:

1. Press the TIMER 1 or TIMER 2 pad once.

2. Press the displayed times on the Quickset

pads until the desired time is entered.

OR

3. Press the number pads to enter the new desired time.

4. Press Enter pad.

Canceling the Timer:

1. Press the TIMER 1 or TIMER 2 pad twice.

If both Timers are active:

If the desired Timer is already in the foreground, press once

for edit mode and twice to cancel the Timer. If the desired

Timer is not in the foreground, follow the steps below.

1. Press the desired TIMER pad once. The selected Timer will

come to the foreground.

2. Press the TIMER pad a second time to access the edit

mode in order to make changes.

3. Pressing the TIMER pad a third time will cancel the Timer.

Changing the Timer beeps:

The signal beeps for TIMER 1 and TIMER 2 can be changed.

The options available are two beeps every thirty seconds, two

beeps every sixty seconds or one beep only. The default

setting is one beep.

1. Press the Setup pad.

2. Select the arrow to scroll until TONES

is displayed.

3. Select TONES.

4. Select TIMERS TONES.

5. Select the desired timer beep format (2-30 SEC., 2-60 SEC.

or 1 BEEP).

6. Press Setup pad to exit Setup mode.

Locking the Control and Oven Door

The oven control and oven door can be locked to prevent

accidental programming. If an oven function is currently

being used, the control and door cannot be locked.

To lock the control and door:

Press the Back and Enter pads at the same time, holding for

three seconds or until CONTROL LOCKED appears in the

display.

To unlock the control and door:

Press the Back and Enter pads at the same time, holding for

three seconds. UNLOCKING DOOR will appear in the display

when the control and door are unlocking.

8113P528-60 10/20/05, 11:56 AM17

17

Notes:

• If more than thirty seconds elapse between pressing a

pad and pressing a number pad, the display will return

to the previous display.

• Whenever the temperature appears in the display, the

oven is heating.

• To change the oven temperature during cooking, press

the Bake pad and select a displayed temperature or use

the number pads to enter the desired temperature.

• The oven will automatically shut off after 12 hours if it is

accidentally left on. To set a Sabbath Mode, see Sabbath

Mode, page 29.

Bake Options

• The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature. Allow about 15 minutes for the oven

to preheat.

• When the oven is preheated, the oven will beep and

PREHEAT will no longer be displayed.

3. At the end of cooking, turn the oven off by

pressing the CANCEL pad. Remove food

from the oven. The oven will continue

operating until the CANCEL pad is pressed.

Baking

To set Bake:

1. Press the Bake pad.

2. Select the oven temperature using the Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 170° F to 550° F

in 5° increments.

• After three seconds, the oven will begin to preheat.

BAKE and PREHEAT will appear in the display along

with 100° or the actual oven temperature, whichever

is higher.

To set a Delay:

1. After Bake has been programmed, press

the More Options pad.

2. Select DELAY.

3. Select the amount of time you want to delay the start of

cooking using the displayed times or the number pads.

4. Select the amount of time you want to cook using the

displayed times or the number pads.

5. The display will show BAKE, the temperature, the delay

time and the cook time countdown.

6. When the delay time has expired, the oven will begin

heating. COOK TIME, the cook time countdown, PREHEAT,

BAKE and the actual oven temperature will be displayed.

CAUTION

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry or seafood.

Cook & Hold (select models) and Delay options are available

when baking. When using the Cook & Hold option (select

models), the oven begins to heat immediately after the control

has been set. Then, the oven cooks for a specified length of

time. When that time has elapsed, the oven will automatically

reduce temperature to 170° F and keep the food warm for up

to an hour and then automatically turn off.

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time. When that time has elapsed, the oven will keep the food

warm for up to an hour then automatically turn off.

To set Cook & Hold (select models):

1. After Bake has been programmed, press

the More Options pad.

2. Select COOK/HLD.

3. Select the amount of time you want to bake by pressing

the Quickset pads or the number pads.

4. Press Enter pad.

5. COOK TIME, the cook time countdown, PREHEAT, BAKE

and the actual temperature will be displayed.

The oven will cook for the selected time, then keep food warm

for one hour.

8113P528-60 10/20/05, 11:56 AM18

18

Convect Bake

To set Convect Bake:

1. Press the Convect pad.

2. Select CNVT BAKE using the Quickset pads.

Convect

Convection uses a fan to circulate hot air evenly over, under

and around the food. As a result, foods are evenly cooked

and browned, often in shorter times, at lower temperatures

and with the flexibility of using more than one rack at a time.

Convect Options

Cook & Hold (select models) and Delay options are available

when convect cooking. See page 22 for information on how

to program a Cook & Hold (select models) or Delay option.

Notes:

• The oven control comes from the factory set for Auto

Convect Conversion (select models). When using

Convect Bake and Convect Pastry enter the conventional

baking temperature. The control automatically converts

the temperature to 25° less than the conventional

temperature.

• For Convect Roast, enter the conventional roasting

temperature and time. The control then lets you know

when 75% of the time has elapsed and alerts you to

check the food for doneness.

• To turn Auto Convect Conversion (select models) off,

see page 28.

CONVECT CONVECT CONVECT

BAKE ROAST PASTRY

Multiple-rack Whole Chicken Frozen Pie

Baking of Whole Turkey Turnovers

Cookies/Biscuits Vegetables Cream Puffs

Breads Pork Roasts Puff Pastry

Casseroles Beef Roasts

Tarts/Tortes

Cakes

3. Select the oven temperature using the Quickset pads

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 195° F to 550° F

degrees in 5° increments.

• After three seconds, the oven will begin to preheat.

CNVT BAKE and PREHEAT will appear in the display

along with 100° or the actual oven temperature,

whichever is higher.

• The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature. Allow about 15 minutes for the oven

to preheat.

• When the oven is preheated, the oven will beep and

PREHEAT will turn off and CNVT BAKE will be displayed.

AUTO will be displayed if Auto Convect Conversion

(select models) feature is turned on.

• Place food in the oven.

4. At the end of cooking, turn the oven off by

pressing the CANCEL pad. Remove food

from the oven. The oven will continue

operating until the CANCEL pad is pressed.

Rapid Preheat

Use to decrease preheating time when using Bake or Convect

Bake. Use for all foods when baking on one rack.

• After Bake or Convect Bake has been programmed, press

the Rapid Preheat pad.

• 1 RACK ONLY will display, after three seconds the display

will show RAPID and PREHEAT.

To return to Standard Preheat:

• Press Rapid Preheat pad again. This will provide standard

preheat. PREHEAT and the selected function will be

displayed.

Notes:

• For best results, use rack position 2 or 3 when using the

Rapid Preheat option.

• For optimum baking and browning results, Rapid Preheat

is not recommended when baking on multiple racks.

8113P528-60 10/20/05, 11:56 AM19

19

Convect Roast

To set Convect Roast:

1. Place food in the oven. The two-piece broiler pan provided

with your oven can be used for convection roasting.

2. Press the Convect pad.

3. Select CNVT ROAST using the

Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 170° F to 550° F

degrees in 5° increments.

5. Enter desired cook time. Enter the conventional roasting

time using the number pads.

• After three seconds, the oven will begin to heat. CNVT

ROAST will appear in the display along with 100° or the

actual oven temperature, whichever is higher.

• The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature.

• Cook time will begin to count down.

6. At 75% of the cooking time the oven will beep to let

you know to check food. Check food using a meat

thermometer. If food is done, take food out of oven and

press CANCEL pad to turn oven off.

7. If food is not done, continue roasting.

Once the set time has elapsed the oven will automatically

go into Keep Warm mode for 1 hour. If

food is taken from the oven before the hour

has elapsed, press CANCEL pad.

Convect Pastry

Convect Pastry is designed to bake pastry items such as

frozen pies, turnovers, cream puffs and puff pastry. Use one

rack while using this feature.

1. Press the Convect pad.

2. Select CNVT PASTRY using the

Quickset pads.

OR

Enter the desired temperature using the number pads.

Press Enter pad to set.

• The temperature can be set from 195° F to 550° F

degrees in 5° increments.

• After three seconds, the oven will begin to preheat.

CNVT PASTRY and PREHEAT will appear in the display

along with 100° or the actual oven temperature, which

ever is higher. AUTO will display if the Auto Convect

Conversion (select models) feature is turned on.

• The temperature in the display will increase in 1°

increments until the oven reaches the preset

temperature. Allow about 15 minutes for the oven to

preheat.

• When the oven is preheated, the oven will beep and

PREHEAT will turn off and CNVT PASTRY will be

displayed.

4. At the end of cooking, turn the oven off by

pressing the CANCEL pad. Remove food

from the oven. The oven will continue

operating until the CANCEL pad is pressed.

4. Select the oven temperature using the Quickset pads.

3. Select the oven temperature using the Quickset pads.

Notes:

• If the recipe suggests preheating the oven, add time to

cook time.

• If Auto is off, roast time will not be required.

8113P528-60 10/20/05, 11:56 AM20

La page charge ...

Jenn-Air Air Cleaner air filter Manuel utilisateur

Jenn-Air Air Cleaner air filter Manuel utilisateur

dans d''autres langues

Documents connexes