Tripp Lite Owner's Manual SmartPro® 1U Rack-Mount Le manuel du propriétaire

Marque: Tripp Lite

Modèle: Owner's Manual SmartPro® 1U Rack-Mount

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Ce manuel convient également à

Owner’s Manual

SmartPro

1U Rack-Mount

Intelligent, Line-Interactive UPS Systems

Important Safety Instructions 2

Mounting 3

Quick Installation 4

Optional Installation 6

Basic Operation 7

Storage and Service 10

Battery Replacement 11

Product Registration 12

Español 13

Français 25

Русский

Deutsch 49

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

is a registered trademark of Tripp Lite.

WARRANTY REGISTRATION

automatically entered to win an ISOBAR

surge protector in our monthly drawing!

tripplite.com/warranty

SMX500RT1U

Series: AG-03AD

SMART500RT1U

Series: AG-03AA

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation, operation

and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty.

UPS Location Warnings

• Use caution when lifting your UPS. Because of the considerable weight of all rack-mount UPS

systems, at least two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the ambient temperature near your UPS should be between 0° C and

40° C (between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its

vents or fan openings.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even

when the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug in a

way that would eliminate the UPS’s connection to ground. Do not use adapters that eliminate

the UPS’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must provide

filtered, frequency-regulated, computer-grade output.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended.

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS. Battery replacement should be performed only by authorized service

personnel using the same number and type of batteries (sealed Lead-Acid). The batteries are

recyclable. Refer to your local codes for disposal requirements or in the USA only call

1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-8-228-8379) or visit www.call2recycle.org for

recycling information. Tripp Lite offers a complete line of UPS System Replacement Battery

Cartridges (R.B.C.). Visit Tripp Lite on the Web at www.tripplite.com to locate the specific

replacement battery for your UPS.

• During hot-swap battery replacement, the UPS will not provide backup power in the event of

a blackout or other power interruptions.

• Do not operate UPS without batteries.

• When adding external battery packs to select models with external battery pack connectors,

connect only Tripp Lite-recommended battery packs of the correct voltage and type. Do not

connect or disconnect battery packs when the UPS is operating on battery power.

Mounting

Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user must

determine the fitness of hardware and procedures before mounting. If hardware and procedures

are not suitable for your application, contact the manufacturer of your rack or rack enclosure. The

procedures described in this manual are for common rack and rack enclosure types and may not

be appropriate for all applications.

4-Post Rack Mounting

UPS models include hardware required to mount in a 4-post rack.

Attach mounting ears

to the front

mounting holes of your equipment

using

the screws provided

. The ears should

face forward.

Using an assistant if necessary, lift your

equipment and mount it to the rack. Attach

it by screwing the appropriate hardware

through its mounting ears and into the rack

rails.

2-Post (Telecom) Rack Mounting

Following the procedures below, mount the 1U UPS model in 2-post racks with the included

hardware.

Attach mounting ears

to the front

mounting holes of your UPS

using the

screws provided

. The ears should face

backward.

Using an assistant if necessary, lift your UPS

and attach it to the rack by passing the

screws, nuts and washers provided

through its mounting ears and into the rack

rails.

Mounting

Quick Installation

Tower Mounting

Mount UPS models in an upright tower position

using included hardware. The user must

determine the fitness of hardware and

procedures before mounting.

Stand your UPS on its side with the LED/Control

panel at the top. Attach one rack mounting ear

to each side of the UPS using included

screws.

Plug the UPS into an outlet on a

dedicated circuit.*

• Connect the SMX500RT1U AC input to

the outlet using one of the two included

1.8 m C13 to C14 power cords, or

connect with a user-supplied cord.

• SMART500RT1U has an attached cable.

NOTE! after plugging the UPS into a live AC outlet,

the UPS (in “Standby” mode) will automatically

charge its batteries**, but will not supply power to

its outlets until it is turned ON (see Step 3 below).

Note: UPS system will function properly upon

initial startup. However, maximum runtime for the

unit’s battery will only be accessible after it has

been charged for 24 hours.

* See Specifications for circuit amperage

requirements.

** The BATTERY CHARGE LED will be the only LED

illuminated.

SMX500RT1U Shown

SMART500RT1U Shown

UNSWITCHED OUTLETS

INPUT

SWITCHED OUTLETSURGE OUTLET

INPUT BREAKER

EPOUSBRS232

ACC.SLOT

Model: SMART500RT1U

Quick Installation

Plug your equipment into the

UPS.*

• For SMX500RT1U, use the second of the

two included 1.8 m C13 to C14 power

cords to connect equipment to the UPS,

or connect with a user-supplied cord.

• Additional power cords are available from

Tripp Lite. Visit tripplite.com.

* Your UPS is designed to support only electronic

equipment. You will overload the UPS if the

total VA ratings for all the equipment you

connect exceeds the UPS’s Output Capacity

(see Specifications). To find your equipment’s

VA ratings, look on their nameplates. If the

equipment is listed in amps, multiply the

number of amps by your UPS’s voltage to

determine VA.

For example: for SMART500RT1U,

1 amp x 120 V = 120 VA; for SMX500RT1U,

1 amp × 230 V = 230 VA. If you are unsure if

you have overloaded the UPS’s outlets, see

“OUTPUT LOAD LEVEL” LED description.

Turn the UPS ON.

Press and hold the “ON/OFF/STANDBY”

button for one second. The alarm will beep

once briefly after one second has passed.

Release the button.

SMX500RT1U Shown

SMART500RT1U Shown

Optional Installation

These connections are optional. Your UPS will function properly without these connections.

4-5

USB and RS-232 Serial

Communications

Use the included USB cable (see

) and/

or DB9 serial cable (see

) to connect the

communication port on your computer to

the communication port of your UPS. Install

on your computer the Tripp Lite PowerAlert

software appropriate to your computer’s

operating system. Your UPS may feature

additional communications ports. These

ports may also be connected to additional

computers which have PowerAlert

software

installed. Consult your PowerAlert manual

for more information.

EPO Port Connection

This optional feature is only for those

applications which require connection to a

facility’s Emergency Power Off (EPO) circuit.

When the UPS is connected to this circuit, it

enables emergency shutdown of the UPS’s

inverter.

Using the cable provided, connect the EPO

port of your UPS (see

) to a user-supplied

normally closed or normally open switch

according to the circuit diagram (see

Note: The EPO port is not a phone line surge

suppressor; do not connect a phone line to this

port.

SMX500RT1U

Shown

SMX500RT1U

Shown

SMX500RT1U

Shown

Basic Operation

LED Interface

Buttons (Front Panel)

“ON/OFF/STANDBY” Button

• To turn the UPS ON: With the UPS plugged into a live AC wall outlet*, press

and hold the “ON/OFF/STANDBY” button for one second.** Release the button.

If utility power is absent, you can “cold-start” the UPS (i.e.: turn it ON and

supply power for a limited time from its batteries***) by pressing and holding

the “ON/OFF/STANDBY” button for one second.**

• To turn the UPS OFF: With the UPS ON and receiving utility power, press and

hold the “ON/OFF/STANDBY” button for one second.** Then unplug the UPS

from the wall outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS (in “Standby” mode) will automatically

charge its batteries, but will not supply power to its outlets until it is turned ON. ** The alarm

will beep once briefly after the indicated interval has passed. *** If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: Briefly press and release the “MUTE/TEST”

button.

To Run a Self-Test: With your UPS plugged in and turned ON, press and hold the

“MUTE/TEST” button for two seconds.* Continue holding the button until the

alarm beeps several times and the UPS performs a self-test. See “Results of a

Self-Test” below.

Note: You can leave connected equipment on during a self-test. Your UPS, however, will not

perform a self-test if the UPS is not turned on (see “ON/OFF/STANDBY” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove

safe electrical grounding and may introduce a damaging surge into your

network connections.

* The alarm will beep once briefly after the indicated interval has passed.

Results of a Self-Test: the test will last approximately 10 seconds as the UPS

switches to battery to test its load capacity and battery charge.

• If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues to

sound after the test, the UPS’s outlets are overloaded. To clear the overload,

unplug some of your equipment and run the self-test repeatedly until the

“OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no longer

sounding.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease

supplying output power in the event of a blackout or brownout.

• If the “BATTERY WARNING” LED remains lit and the alarm continues to

sound after the test, the UPS batteries need to be recharged or replaced.

Allow the UPS to recharge continuously for 12 hours, and repeat the self-

test. If the LED remains lit, contact Tripp Lite for service. If your UPS requires

battery replacement, visit tripplite.com to locate the specific Tripp Lite

replacement battery for your UPS.

Basic Operation

Indicator Lights (Front Panel)

All Indicator Light descriptions apply when the UPS is plugged into a wall outlet and turned ON.

“POWER” LED: This green LED lights continuously when the UPS is ON and

supplying connected equipment with AC power from a utility source. The LED

flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe brownout.

If the blackout or severe brownout is prolonged, you should save files and shut

down your equipment, since internal battery power will eventually be depleted.

See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: This green LED lights continuously whenever the

UPS is automatically correcting high or low AC voltage on the utility line without

the assistance of battery power. The UPS will also emit a slight clicking noise.

These are normal, automatic operations of the UPS; no action is required on your

part.

“OUTPUT LOAD LEVEL” LED: This multicolored LED indicates the approximate

electrical load of equipment connected to the UPS’s AC outlets. It will turn from

green (light load) to yellow (medium load) to red (overload). If the LED is red

(either illuminated continuously or flashing), clear the overload immediately by

unplugging some of your equipment from the outlets until the LED changes from

red to yellow (or green). CAUTION! Any overload that is not corrected by the user

immediately may cause the UPS to shut down and cease supplying output power

in the event of a blackout or brownout.

“BATTERY CHARGE” LED: When the UPS is operating from utility power, this LED

indicates the approximate charge state of the UPS’s internal batteries: red

indicates the batteries are beginning to charge, yellow indicates the batteries are

roughly midway through charging, and green indicates the batteries are fully

charged. When the UPS is operating from battery power during a blackout or

severe brownout, this LED indicates the approximate amount of energy

(ultimately affecting runtime) which the UPS’s batteries will provide: red indicates

a low level of energy, yellow indicates a medium level of energy, and green

indicates a high level of energy. Since the runtime performance of all UPS

batteries will gradually deplete over time, it is recommended that you periodically

perform a self-test (see “MUTE/TEST” Button description) to determine the energy

level of your UPS batteries BEFORE a blackout or severe brownout occurs. During

a prolonged blackout or severe brownout, you should save files and shut down

your equipment, since battery power will eventually be depleted. When the LED

turns red and an alarm sounds continuously, it indicates the UPS’s batteries are

nearly out of power and UPS shut down is imminent.

“BATTERY WARNING” LED: This LED lights red and an alarm sounds

intermittently after you complete a self-test (See “MUTE/TEST” Button

description) to indicate the UPS batteries need to be recharged or replaced.

Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If

the LED continues to light, contact Tripp Lite for service. If your UPS requires

battery replacement, visit tripplite.com to locate the specific Tripp Lite

replacement battery for your UPS.

Basic Operation

Other UPS Features (Rear Panel)

C13

NEMA 5-15R

AC Receptacles: Your UPS features C13 outlets (SMX500RT1U) or NEMA

5-15R outlets (SMART500RT1U). These outlets provide your connected

equipment with AC line power during normal operation and battery power during

blackouts and brownouts. The UPS protects equipment connected to these

receptacles against damaging surges and line noise. If you have a serial or

USB connection to your UPS, you can remotely reboot connected equipment

by turning receptacles OFF and ON using Tripp Lite’s PowerAlert software.

Models also feature outlets labeled “UNSWITCHED” which may not be remotely

turned off.

Communications Ports (USB or RS-232): These ports connect your UPS to

any workstation or server. Use with Tripp Lite’s PowerAlert software and included

cables to enable your computer to automatically save open files and shut down

equipment during a blackout. Also use PowerAlert to monitor a wide variety of

AC line power and UPS operating conditions. Consult your PowerAlert manual or

contact Tripp Lite Customer Support for more information. See “USB and

RS-232 Serial Communications” in the “Optional Installation” section for

installation instructions.

EPO (Emergency Power Off) Port: Your UPS features an EPO port that may be

used to connect the UPS to a contact closure switch to enable emergency

inverter shutdown. See “Optional Installation” section.

Accessory Slot: Remove the small cover panel from this slot to install optional

accessories to remotely monitor and control your UPS. Refer to your

accessory’s manual for installation instructions. Contact Tripp Lite at

tripplite.com/support for more information, including a list of available SNMP,

network management and connectivity products.

Input Breaker(s): Protect an electrical circuit from overcurrent draw from the

UPS load. If one or more breakers trip, remove some of the load, then reset

them by pressing the breaker(s) in.

Ground Screw: Use this to connect any equipment that requires a chassis

ground.

Storage and Service

Storage

Before storing your UPS, turn it completely OFF: With the UPS ON and receiving utility power, press

and hold the “ON/OFF/STANDBY” button for one second (an alarm will beep once briefly after the

interval has passed), then unplug the UPS from the wall outlet. If you store your UPS for an

extended period of time, recharge the UPS batteries once every three months: plug the UPS into a

wall outlet, allow it to charge for 12 hours, and then unplug it and place it back in storage. Note:

after you plug the UPS in, it will automatically begin charging its batteries. However, it will not

supply power to its outlets (see Quick Installation section). If you leave your UPS batteries

discharged for an extended period of time, they will suffer a permanent loss of capacity.

Service

Before returning your UPS for service, follow these steps:

1. Review the installation and operation instructions in this manual to ensure that the service

problem does not originate from a misreading of the instructions. Also, check that the UPS

System’s circuit breaker(s) are not tripped. This is the most common cause of service

inquiries, which can be easily remedied by following the resetting instructions in this manual.

2. If the problem continues, do not contact or return the UPS to the dealer. Instead, contact

Tripp Lite at tripplite.com/support. A service technician will ask for the UPS’s model number,

serial number and purchase date.

3. If the problem requires service, the technician will issue you a Returned Material Authorization

(RMA) number, which is required for service. If you require packaging, the technician can

arrange to send you proper packaging. Securely pack the UPS to avoid damage during shipping.

Do not use Styrofoam beads for packaging. Any damages (direct, indirect, special, incidental or

consequential) to the UPS incurred during shipment to Tripp Lite or an authorized Tripp Lite

service center is not covered under warranty. UPS Systems shipped to Tripp Lite or an authorized

Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on

the outside of the package. If the UPS System is within the 2-year warranty period, enclose a

copy of your sales receipt. Return the UPS for service using an insured carrier to the address

given to you by the Tripp Lite service technician.

Battery Replacement

Under normal conditions, the original batteries in your UPS will last many years. See “Safety”

section before replacing batteries. The batteries are designed for hot-swap replacement

(i.e. leaving the UPS in ON mode), but qualified service personnel may wish to put the UPS in

the OFF mode before proceeding.

Procedure

Remove Front Panel

Disconnect Batteries

Remove/Dispose of Batteries

Add Batteries

Connect Batteries

Attach connectors: black-to-black and red-to-red.

Replace Front Panel

REMOVE / REPLACE FRONT PANEL

DISCONNECT / CONNECT BATTERIES

PULL / PUSH

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

FCC RADIO/TV INTERFERENCE NOTICE: (FOR CLASS A MODELS)

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when operated in a commercial environment. This equipment generates, uses and can radiate radio

frequency energy, and if not installed and used in accordance with the instruction manual, may cause

interference to radio communications. Operation of this equipment is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense. The user must use shielded

cables and connectors with this product. Any changes or modifications to this product not expressly approved by

the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RADIO/TV INTERFERENCE NOTICE: (FOR CLASS B MODELS)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy,

and if not installed and used in accordance with the instruction manual, may cause interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference using one or more of the

following measures: reorient or relocate the receiving antenna; increase the separation between the equipment

and the receiver; connect the equipment into an outlet on a circuit different from that which the receiver is

connected; consult the dealer or an experienced radio/television technician for help. The user must use shielded

cables and connectors with this product. Any changes or modifications to this product not expressly approved by

the party responsible for compliance could void the user’s authority to operate the equipment. This device

complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may

not cause harmful interference, and (2) This device must accept any interference received, including interference

that may cause undesired operation.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been

assigned a unique series number. The series number can be found on the product nameplate label, along with

all required approval markings and information. When requesting compliance information for this product, always

refer to the series number. The series number should not be confused with the marketing name or model

number of the product.

Tripp Lite has a policy of continuous improvement. Product specifications are subject to change without notice.

Photos and illustrations may differ slightly from actual products.

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V : DC Voltage

Product Registration

Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a

drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See Web site for details.

19-12-053 93-3903_revB

Manual del Propietario

SmartPro

1U para

Instalación en Rack

Sistemas UPS Inteligentes, Interactivos

Instrucciones de Seguridad Importantes 14

Instalación 15

Instalación Rápida 16

Instalación Opcional 18

Operación Básica 19

Almacenamiento y Servicio 22

Reemplazo de la Batería 23

Registro del Producto 24

English 1

Français 25

Русский

Deutsch 49

1111 W. 35th Street, Chicago, IL 60609 EE. UU. • tripplite.com/support

es una marca registrada de Tripp Lite.

SMX500RT1U

Serie: AG-03AD

SMART500RT1U

Serie: AG-03AA

Instrucciones de Seguridad Importantes

CONSERVE ESTAS INSTRUCCIONES

Este manual contiene instrucciones importantes que deben seguirse durante la instalación,

operación y almacenamiento de todos los Sistemas UPS de Tripp Lite. No observar estas

instrucciones y advertencias anulará la garantía del producto.

Advertencias en relación con la ubicación del UPS

• Tenga cuidado al levantar su UPS. Debido al peso considerable de todos los sistemas UPS para

instalación en rack, al menos dos personas deben ayudar a levantarlos e instalarlos.

• Instale su UPS en interiores, alejado de humedad o calor excesivos, polvo o luz solar directa.

• Para un mejor rendimiento, la temperatura ambiente cerca de su UPS debe estar entre 0 °C y

40 °C (entre 32 °F y 104 °F).

• Deje suficiente espacio alrededor de todos los lados del UPS para una ventilación apropiada. No

obstruya las rejillas o aberturas de ventilación.

Advertencias en relación con la Conexión del UPS

• El UPS contiene su propia fuente de energía (batería). Las terminales de salida pueden estar

energizadas, aún cuando el UPS no esté conectado a una alimentación de CA.

• Conecte su UPS a un tomacorrientes de CA conectado correctamente a tierra. No modifique la

clavija del UPS de modo tal que pueda eliminar la conexión a tierra del UPS. No use

adaptadores que eliminen la conexión a tierra del UPS.

• No enchufe su UPS en sí mismo; esto dañará al UPS y anulará su garantía.

• Si está conectando su UPS a un generador de CA con motor, el generador debe proporcionar

una salida de grado computadora, filtrada y con frecuencia regulada.

Advertencias en relación con la Conexión del Equipo

• No se recomienda utilizar este equipo en aplicaciones de soporte de vida donde una falla podría

llegar a causar la falla del equipo de soporte de vida o afectar significativamente su seguridad o

efectividad.

• No conecte supresores de sobretensiones o cables de extensión a la salida de su UPS. Esto

puede sobrecargar al UPS y anulará las garantías del supresor de sobretensiones y del UPS.

Advertencias en relación con la Batería

• Las baterías pueden presentar un riesgo de descarga eléctrica y quemaduras por la corriente

elevada de cortocircuito. Tome las precauciones correspondientes. No arroje las baterías al

fuego. No abra el UPS o las baterías. No ponga en corto o puentee las terminales de la batería

con algún objeto. Desenchufe y apague el UPS antes de reemplazar la batería. Use herramientas

con mangos aislados. No hay partes dentro del UPS a las que el usuario pueda dar servicio. El

reemplazo de la batería debe realizarlo solo personal de servicio autorizado usando el mismo

número y tipo de baterías (Plomo-Ácido selladas). Las baterías son reciclables. Consulte los

códigos locales para los requisitos de la disposición o en los Estados Unidos solo llame a

1-800-SAV-LEAD o 1-800-8-BATTERY (1-800-8-228-8379) o visite www.call2recycle.org para

obtener información sobre el reciclaje. Tripp Lite ofrece una línea completa de Cartuchos de

batería de repuesto (R.B.C.) para sistemas UPS. Para localizar la batería de repuesto específica

para su UPS, visite Tripp Lite en el sitio www.tripplite.com.

• Durante el reemplazo Hot-Swap de la batería, el UPS no suministrará energía de respaldo en

caso de un apagón y otras interrupciones de energía.

• No opere el UPS sin baterías.

• Al agregar módulos de baterías externas para modelos selectos con conectores para módulos de

baterías externas, solo conecte módulos de baterías recomendados por Tripp Lite del voltaje y

tipo correctos. No conecte ni desconecte los módulos de batería cuando el UPS esté

funcionando con energía de la batería.

Instalación

instale su equipo es un rack o gabinete de 4 postes o de 2 postes. Antes de la instalación, el

usuario debe determinar la conveniencia de los accesorios y procedimientos. Si los accesorios y

procedimientos no son adecuados para su aplicación, póngase en contacto con el fabricante de su

rack o gabinete. Los procedimientos descritos en este manual son para tipos comunes de racks y

gabinetes y pueden no ser apropiados para todas las aplicaciones.

Instalación en Rack de 4 Postes

Los modelos de UPS incluyen los accesorios requeridos para instalar en un rack de 4 postes.

Coloque las orejas de instalación

en los

orificios frontales de instalación de su

equipo

usando los tornillos suministrados

. Las orejas deben apuntar al frente.

Con ayuda de otra persona si fuera

necesario, levante su equipo e instálelo en

el rack. Sujételo atornillando los accesorios

adecuados

a través de sus orejas de

instalación y en los rieles del rack.

Instalación en Rack de 2 Postes (Telecomunicaciones)

Siguiendo los procedimientos descritos a continuación, instale el modelo de UPS de 1U en racks

de 2 postes con los accesorios incluidos.

Coloque las orejas de instalación

en los

orificios frontales de instalación de su UPS

usando los tornillos suministrados

. Las

orejas deben apuntar hacia atrás.

Con la ayuda de otra persona si fuera

necesario, levante su UPS y colóquelo en el

rack pasando los tornillos, tuercas y

arandelas suministrados

a través de sus

orejas de instalación y en los rieles del rack.

Instalación

Instalación Rápida

Instalación en Torre

Instale los modelos de UPS en una posición de

torre vertical usando los accesorios incluidos.

Antes de la instalación, el usuario debe

determinar la conveniencia de los accesorios y

procedimientos.

Coloque su UPS en su sitio con el panel de

LED/Control en la parte superior. Fije la oreja de

instalación en rack

a cada lado del UPS

usando los tornillos incluidos.

Enchufe el UPS en un

tomacorriente en un circuito

dedicado.*

• Conecte la entrada de CA del

SMX500RT1U al tomacorriente usando

uno de los dos cables de alimentación

C13 a C14 de 1.8 m incluidos o conecte

con un cable suministrado por el usuario.

• El SMART500RT1U tiene un cable

conectado.

Nota: Después de conectar el UPS en un

tomacorriente activo de CA, el UPS (en modo de

espera) cargará automáticamente sus baterías**,

pero no suministrará energía a sus tomacorrientes

hasta que se encienda (ver paso 3 a

continuación).

Nota: El sistema UPS funcionará correctamente

desde el arranque inicial. No obstante, la

autonomía máxima para la batería de la unidad

solo será accesible después de haberse cargado

por 24 horas.

* Consulte las especificaciones para los requisitos

de amperaje del circuito.

** El LED "BATTERY CHARGE" [Carga de Batería]

será el único LED iluminado.

Se muestra SMX500RT1U

Se muestra SMART500RT1U

UNSWITCHED OUTLETS

INPUT

SWITCHED OUTLETSURGE OUTLET

INPUT BREAKER

EPOUSBRS232

ACC.SLOT

Model: SMART500RT1U

Instalación Rápida

Enchufe su equipo en el UPS.*

• Para SMX500RT1U, utilice el segundo de

los dos cables de alimentación C13 a

C14 de 1.8 m para conectar el equipo al

UPS o conecte con un cable

suministrado por el usuario.

• Existen cables de alimentación

adicionales disponibles en Tripp Lite.

Visite tripplite.com.

* Su UPS está diseñado para soportar solamente

equipo electrónico. Usted sobrecargará el UPS

si el valor total en VA para todo el equipo que

conecte excede la capacidad de salida del UPS

(ver Especificaciones). Para localizar los valores

de VA de su equipo, consulte sus placas de

identificación. Si el equipo está especificado en

amperes, multiplique el número de amperes

por el voltaje de su UPS para determinar los VA.

Por ejemplo: para SMART500RT1U,

1 amp x 120 V = 120 VA; para SMX500RT1U,

1 amp x 230 = 230 VA. Si no está seguro de

si ha sobrecargado las salidas del UPS,

consulte la descripción de LED "NIVEL DE

CARGA DE SALIDA".

Encienda el UPS.

Oprima y sostenga por un segundo el botón

"ON/OFF/STANDBY". La alarma emitirá un

breve bip después de transcurrido un

segundo. Suelte el botón.

Se muestra SMX500RT1U

Se muestra SMART500RT1U

Instalación Opcional

Estas conexiones son opcionales. Su UPS trabajará correctamente sin estas conexiones.

4-5

USB y Serial RS-232

Comunicaciones

Use el cable USB incluido (ver

) o el

cable serial DB9 (ver

) para conectar el

puerto de comunicación de su

computadora al puerto de comunicación de

su UPS. Instale en su computadora el

software PowerAlert de Tripp Lite adecuado

para el sistema operativo de su

computadora. Su UPS puede contar con

puertos de comunicación adicionales. Estos

puertos pueden conectarse también a

computadoras adicionales que tengan

instalado el Software PowerAlert

. Para

más información, consulte su manual de

PowerAlert.

Conexión de Puerto EPO

Esta función opcional es solo para aquellas

aplicaciones que requieran conexión a un

circuito de Apagado de Emergencia (EPO) de

la instalación. Cuando el UPS está conectado

a este circuito, habilita el apagado de

emergencia del inversor del UPS.

Con el cable proporcionado, conecte el

puerto de EPO de su UPS (ver

) a un

switch normalmente cerrado o normalmente

abierto, proporcionado por el usuario, de

acuerdo con el diagrama del circuito (ver

Nota: El puerto de EPO no es un supresor de

sobretensiones de línea telefónica; no conecte una

línea telefónica a este puerto.

Se muestra

SMX500RT1U

Se muestra

SMX500RT1U

Se muestra

SMX500RT1U

Operación Básica

Interfaz LED

Botones (Panel Frontal)

Botón "ON/OFF/STANDBY"

• Para encender el UPS: Con el UPS enchufado en un tomacorriente de CA

activo de pared*, presione y sostenga por un segundo el botón "ON/OFF/

STANDBY".** Suelte el botón. Si no hubiera energía de la red pública, usted

puede "arrancar en frío” el UPS (es decir, enciéndalo y suministre energía de

sus baterías por un tiempo limitado ***) presionando y sosteniendo por un

segundo el botón "ON/OFF/STANDBY".**

• Para apagar el UPS: Con el UPS ENCENDIDO y recibiendo energía de la red

pública, presione y sostenga por un segundo el botón "ON/OFF/STANDBY".**

Después desconecte el UPS del tomacorrientes de la pared. El UPS se apagará

por completo.

* Después de conectar el UPS en un tomacorriente de CA activo, el UPS (en modo de

"espera") cargará automáticamente sus baterías, pero no suministrará energía a sus

tomacorrientes hasta que se encienda. ** La alarma sonará brevemente una vez después

de transcurrido el intervalo indicado. *** Si están completamente cargadas.

Botón "MUTE/TEST" [Silenciar / Prueba]

Para silenciar las alarmas del UPS: Oprima brevemente y libere el botón

MUTE/TEST.

Para ejecutar un Autodiagnóstico: Con su UPS enchufado y encendido, oprima

y sostenga por dos segundos el botón MUTE/TEST.* Continúe sosteniendo el

botón hasta que la alarma suene varias veces y el UPS ejecute un

autodiagnóstico. Vea a continuación "Resultados de un Autodiagnóstico".

Nota: Puede dejar equipo conectado durante un autodiagnóstico. No obstante, su UPS no

ejecutará un autodiagnóstico si no está encendido (consulte la descripción del Botón "ON/

OFF/STANDBY").

¡PRECAUCIÓN! No desconecte su UPS para probar las baterías. Esto

eliminará la conexión segura a tierra y puede introducir una sobretensión

dañina en las conexiones de su red.

* La alarma sonará brevemente una vez después de transcurrido el intervalo señalado.

Resultados de un Autodiagnóstico: La prueba durará aproximadamente 10

segundos mientras el UPS cambia a la batería para probar su capacidad de

carga y la carga de la batería.

• Si el LED "OUTPUT LOAD LEVEL" [Nivel de Carga de Salida] permanece

encendido en rojo y la alarma continúa sonando después de la prueba, los

tomacorrientes del UPS están sobrecargados. Para eliminar la sobrecarga,

desconecte algunos de sus equipos y corra repetidamente el autodiagnóstico

hasta que el LED "OUTPUT LOAD LEVEL" [Nivel de Carga de Salida] ya no

permanezca encendido y la alarma ya no suene.

¡PRECAUCIÓN! Cualquier sobrecarga que no sea corregida de inmediato

por el usuario siguiendo un autodiagnóstico puede causar que el UPS

se apague y deje de suministrar energía de salida en caso de un

apagón o caída de voltaje.

Operación Básica

Luces Indicadoras (Panel Frontal)

Todas las descripciones de las Luces Indicadoras se aplican cuando se enchufa el UPS en un

tomacorriente de pared y encendido.

LED "POWER" [Encendido]: Este LED verde enciende continuamente cuando el

UPS está encendido y suministrando energía de CA a los equipos conectados

desde una fuente de alimentación de servicio. El LED destella y suena una alarma

(4 bips cortos seguidos de una pausa) para indicar que el UPS está funcionando

desde sus baterías internas durante un apagón o severa caída de voltaje. Si se

prolonga el apagón o una caída seria de voltaje, debe guardar sus archivos y

apagar su equipo ya que la energía de la batería interna a la larga se agotará. Vea

a continuación la descripción de LED "BATTERY CHARGE" [Carga de la Batería].

LED "VOLTAGE CORRECTION" [Corrección de Voltaje]: Este LED verde se

enciende permanentemente cuando el UPS está corrigiendo automáticamente

un voltaje de CA alto o bajo en la alimentación de servicio sin el apoyo de la

energía de la batería. El UPS emitirá también un ligero clic. Esto es normal, son

operaciones automáticas del UPS, no se requiere acción de su parte.

LED "OUTPUT LOAD LEVEL" [Nivel de Carga de Salida]: Este LED multicolor

indica la carga eléctrica aproximada del equipo conectado a los tomacorrientes

de CA del UPS. Cambiará de verde (carga ligera) a amarillo (carga media) a rojo

(sobrecarga). Si el LED está rojo (ya sea iluminado continuamente o

destellando), elimine de inmediato la sobrecarga desconectando algo de su

equipo de los tomacorrientes hasta que el LED cambie de rojo a amarillo (o

verde). ¡PRECAUCIÓN! Cualquier sobrecarga que no sea corregida de inmediato

por el usuario, puede causar que el UPS se apague y deje de suministrar energía

de salida en caso de un apagón o caída de voltaje.

LED "BATTERY CHARGE" [Carga de Batería]: Cuando el UPS esté operando de

la energía de la red pública, este LED indica el estado aproximado de carga de

las baterías internas del UPS: rojo indica que las baterías están empezando a

cargar; amarillo indica que las baterías están aproximadamente a la mitad de la

carga; y verde indica que las baterías están completamente cargadas. Cuando el

UPS esté operando con energía de la batería durante un apagón o caída seria de

voltaje, este LED indica la cantidad aproximada de energía (lo que finalmente

afectan la autonomía) que proporcionarán las baterías del UPS: rojo indica un

bajo nivel de energía, amarillo indica un nivel medio de energía; y verde indica

un alto nivel de energía. Dado que el rendimiento de autonomía de todas las

baterías de UPS se agotará gradualmente a través del tiempo, es recomendable

que usted realice un auto-diagnóstico periódico (ver descripción de Botón "MUTE/

TEST") para determinar el nivel de energía de sus baterías del UPS ANTES que

ocurra un apagón o caída seria de voltaje. Durante un apagón o caída severa de

voltaje prolongado, deberá guardar sus archivos y apagar su equipo ya que la

energía de la batería a la larga se agotará. Cuando el LED se pone rojo y suena

continuamente una alarma, indica que las baterías del UPS están próximas a

agotarse y es inminente el apagado del UPS.

• Si el LED "BATTERY WARNING" [Advertencia de batería] permanece

encendido y la alarma continúa sonando después de la prueba, las baterías

del UPS necesitan ser recargadas o reemplazadas. Deje que el UPS se

cargue de manera continua durante 12 horas y repita el autodiagnóstico. Si

el LED permanece encendido, solicite servicio a Tripp Lite. Si su UPS

requiere reemplazo de la batería, visite tripplite.com para localizar la batería

de remplazo específica de Tipp Lite para su UPS.

La page charge ...

Tripp Lite Owner's Manual SmartPro® 1U Rack-Mount Le manuel du propriétaire

Marque: Tripp Lite

Modèle: Owner's Manual SmartPro® 1U Rack-Mount

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

Documents connexes

Autres documents

Humanscale NeatHub Mode d'emploi