Infinity INTERMEZZO 2.6 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Owner’s Guide
INTERMEZZO
2.6
ii
INTERMEZZO 2.6
THIS INFINITY PRODUCT IS DESIGNED FOR 120-VOLT USE ONLY! FOR
DETAILED SAFETY PRECAUTIONS, PLEASE SEE FOLLOWING PAGE IN THIS
OWNER’S MANUAL FOR “IMPORTANT SAFETY INSTRUCTIONS.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.
Léclair avec le symbole de la flèche, placé dans les limites d’un triangel équilatéral est
prévu pour avertir l’utilisateur de la présence de “tension dangereuse” non isolée dans
l’enceinte du produit qui pourrait être d’une importance suffisante pour présenter un
risque d’électrocution aux personnes.
Le point d’exclamation dans un triangel équilateral est prévu pour avertir l’utilisateur
de la présence d’instructions importantes pour les opérations et l’entretien (service)
dans les manuels fournis avec l’appareil.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.
Este destello luminoso con un símbolo de punta de flecha dentro de un triángulo
equilátero tiene el objectivo de alertar al usuario sobre la presencia de “voltaje
peligroso” no aislado dentro de la caja del producto que puede ser de magnitud lo
suficientemente grande para constituir un riesgo de choque eléctrico para las personas.
Este punto de exclamación dentro de un triángulo equilátero tiene el objectivo de
alertar al usuario sobre la existencia de instrucciones operativas y de mantenimiento
(servicio) importantes en la literatura que acomaña el aparato.
CUIDADO: PARA REDUCIR EL RIESGO DE CHOQUE ELÉCTRICO, NO
RETIRE LA CUBIERTA (O RESPALDO). DENTRO NO HAY PEIZAS A LAS
QUE EL USUARIO PUEDE DAR SERVICIO. REMITA EL SERVICIO AL
PERSONAL DE SERVICIO CALIFICADO.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD, DO NOT OPEN.
AVIS: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR.
CUIDADO: PELIGRO DE CHOQUE ELÉCTRICO – NO ABRIR.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (0R BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
Read First!
1.Read Instructions.All the safety and operating
instructions should be read before the product is
operated.
2.Retain Instructions.The safety and operating
instructions should be retained for future reference.
3.Heed Warnings. All warnings on the product and in
the operating instructions should be adhered to.
4.Follow Instructions. All operating and use
instructions should be followed.
5.Cleaning. Unplug this product from the wall outlet
before cleaning.Do not use liquid cleaners or aerosol
cleaners.Use a damp cloth for cleaning.
6.Attachments. Do not use attachments not
recommended by the product manufacturer,
as they may cause hazards.
7.Water and Moisture.To reduce the risk of fire or
electric shock,do not use this product outdoors or
near waterfor example,near a bathtub,wash bowl,
kitchen sink or laundry tub;in a wet basement;near a
swimming pool;or the like.
8.Accessories. Do not place this product on an
unstable cart,stand,tripod,bracket or table.The
product may fall,causing serious injury to a child or
adult,and serious damage to the product.Use only
with a cart,stand,tripod,bracket or table
recommended by the manufacturer,or sold with the
product.Any mounting of the product should follow the
manufacturer’s instructions,and should use a
mounting accessory recommended by the
manufacturer.
9.A Product and Cart Combination
Should Be Moved with Care. Quick
stops,excessive force and uneven
surfaces may cause the product and
cart combination to overturn.
10.Ventilation. Slots and openings in the cabinet are
provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating,and these openings must not be blocked
or covered.The openings should never be blocked by
placing the product on a bed,sofa,rug or other
similar surface.This product should not be placed in a
built-in installation,such as a bookcase or rack,
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11.Power Sources.This product should be operated
only from the type of power source indicated on the
marking label.If you are not sure of the type of power
supply to your home,consult your product dealer or
local power company.For products intended to operate
from battery power,or other sources,refer to the
operating instructions.
12.Grounding or Polarization.This product may be
equipped with a polarized alternating-current-line plug
(a plug having one blade wider than the other).This
plug will fit into the power outlet only one way.This is
a safety feature.If you are unable to insert the plug
fully into the outlet,try reversing the plug.If the plug
should still fail to fit,contact your electrician to
replace your obsolete outlet.Do not defeat the safety
purpose of the polarized plug.
13.Power-Cord Protection. Power-supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them,paying
particular attention to cords at plugs,convenience
receptacles,and the point where they exit from the
product.
14.Nonuse Periods.The power cord of the product
should be unplugged from the outlet when left unused
for long periods of time.
15.Outdoor Antenna Grounding. If an outside antenna
or cable system is connected to the product,be sure
the antenna or cable system is grounded so as to
provide some protection against voltage surges and
built-up static charges.Article 810 of the National
Electrical Code,ANSI/NFPA 70,provides information
with regard to proper grounding of the mast and
supporting structure,grounding of the lead-in wire to
an antenna discharge unit,size of grounding
conductors,location of antenna-discharge unit,
connection to grounding electrodes,and requirements
for the grounding electrode.See Figure A.
16.Lightning. For added protection for this product
during a lightning storm,or when it is left unattended
and unused for long periods of time,unplug it from
the wall outlet and disconnect the antenna or cable
system.This will prevent damage to the product due to
lightning and power-line surges.
17.Power Lines.An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits,or where it can
fall into such power lines or circuits.When installing
an outside antenna system,extreme care should be
taken to keep from touching such power lines or
circuits,as contact with them might be fatal.
18.Overloading. Do not overload wall outlets,extension
cords,or integral convenience receptacles,as this can
result in a risk of fire or electric shock.
19.Object and Liquid Entry. Never push objects of any
kind into this product through openings,as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock.Never spill
liquid of any kind on the product.
20.Servicing. Do not attempt to service this product
yourself,as opening or removing covers may expose
you to dangerous voltage or other hazards.Refer all
servicing to qualified service personnel.
21.Damage Requiring Service. Unplug this product
from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. The power-supply cord or the plug has been
damaged;or
b. Objects have fallen onto,or liquid has been spilled
into,the product;or
c. The product has been exposed to rain or water;or
d. The product does not operate normally when
following the operating instructions.Adjust only those
controls that are covered by the operating instructions,
as an improper adjustment of other controls may
result in damage and will often require extensive work
by a qualified technician to restore the product to its
normal operation;or
e. The product has been dropped or damaged in any
way;or
f. The product exhibits a distinct change in
performance;this indicates a need for service.
22.Replacement Parts. When replacement parts are
required,be sure the service technician has used
replacement parts specified by the manufacturer or
that have the same characteristics as the original
part.Unauthorized substitutions may result in fire,
electric shock or other hazards.
23.Safety Check. Upon completion of any service or
repairs to this product,ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
24.Wall or Ceiling Mounting.The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
25.Heat.The product should be situated away from
heat sources such as radiators,heat registers,stoves
or other products (including amplifiers) that produce
heat.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
Antenna Lead-In Wire
Ground Clamp
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductors (NEC Section 810-21)
Electric Service Equipment
Ground Clamps
Power Service Grounding Electrode System
(NEC Art. 250, Part H)
Figure A.
Example of Antenna Grounding as per
National ElectricalCode ANSI/NFPA 70
IMPORTANT SAFETY PRECAUTIONS
iii
INTERMEZZO 2.6
ii Caution
iii Important Safety Precautions
1 Technology
2 Unpacking the Product/Included Accessories
3 Placement
4 Controls and Connections
6 Room Adaptive Bass Optimization System
(R.A.B.O.S.)
7 Contents of the R.A.B.O.S.Test CD
7 The R.A.B.O.S.Sound-Level Meter (RSLM)
12 What You Measure,What To Do
15 Adjusting the R.A.B.O.S.Equalizer
16 Final System Balance
16 Maintenance and Service
17 Specifications
18 Appendix
19 R.A.B.O.S. Measurement Templates
22 Notes
Table of Contents
INTERMEZZO 2.6 OWNERS GUIDE
iv
INTERMEZZO 2.6
1
INTERMEZZO 2.6
Intermezzo Series loudspeakers incorporate several innovative
technologies that,when implemented by exceptional engineering
talent after hours upon hours of subjective listening evaluations,
result in a loudspeaker that realistically and accurately reproduces
the signal source with minimal distortion and coloration.
CeramicMetalMatrixDiaphragms
(C.M.M.D.)
For decades,loudspeaker engineers have known that the ideal
transducer should be stiff,yet light,and have high internal
damping (damping is a material’s ability to absorb energy).
Infinity’s C.M.M.D.transducer is a significant advance in
transducer technology.Ceramic,a class of material new to
loudspeakers,offers better performance than that of other
materials.Ceramic is stiffer than metals and lighter than plastics
and typical composite materials;it also offers improved damping.
These ceramic-based transducers take us a giant step closer to
the ever-elusive “ideal transducer.
In tweeters,C.M.M.D.technology offers stiffness and damping
superior to that of traditional metals and soft-dome materials.
In woofer and midrange applications,it offers accurate pistonic
operation over the entire frequency range of the driver,
completely eliminating coloration due to cone breakup and
dramatically reducing distortion.And when ceramic-metal-matrix
transducers are exposed to moisture,sunlight or extreme
temperatures,their performance does not deteriorate.
In addition to ceramic diaphragms,all the transducers incorporate
magnetic shielding and rigid cast-frames that,through our FEA
computer modeling and scanning-laser-vibrometer measurements,
have been optimized to reduce resonances.This ensures minimal
distortion and incomparable performance.
Amplifier
BASH
®
is an amplifier-power-supply technology that increases
efficiency by reducing power dissipation in the output section.
The BASH topology uses a high-efficiency,fast-response,switch-
mode power supply that provides the main voltage rails for a
linear Class-AB amplifier.By varying the output of the power
supply with the audio signal being amplified,a constant voltage
drop across the output transistors of the linear amplifier can be
maintained.This means that the power dissipation in the output
transistors is greatly reduced.
The result is an extremely efficient audio amplifier that does not
compromise audio performance.
Room-Friendly Acoustical Design
Driver quality is not the only requirement for exceptional
performance.Infinity’s engineers understand that the room in
which the loudspeaker is placed can greatly affect its
performance.To ensure that Intermezzo Series loudspeakers will
sound exceptional in even the most unexceptional listening
environment,Infinity has developed two ways to solve most room-
generated problems.The first is its proprietary Room Adaptive
Bass Optimization System. With a single band of parametric
equalization,the Intermezzo 2.6 can be adjusted to tame any
problematic room bass resonances below 80Hz.
There is a completely different set of room-related problems that
has to do with loudspeaker directivity and that can affect the
reproduction of mid and high frequencies.One characteristic of
forward-facing loudspeakers is that the sound output lessens as
one moves away from the principal axis.This happens both
horizontally and vertically and it means that radiated sounds that
are reflected from the floor,ceiling and side walls will be lower
in amplitude than direct,forward sound.This is usually a good
thing.But,if the dispersion characteristics of the loudspeaker
are different at various frequencies,the sound quality of the
reflected sounds will be very different both from each other and
from the first (i.e.,direct) sound.The ears don’t ignore these
differences; they perceive them as coloration,or as sound quality
that’s been degraded.Intermezzo loudspeakers have been
carefully designed to maintain a directional pattern that is
similar at every important angle,on and off axis.The positive
result is that both direct and reflected sounds arriving at the
listeners’ears have similar timbral signatures.
Completing the Experience
The technology and performance that make Infinity Intermezzo
loudspeakers ideal for music listening also make them the
perfect digital multichannel loudspeaker system.To complete a
home-theater system,Infinity has designed,to the same precise
standards as for Intermezzo 2.6,a matching 3-way center-
channel loudspeaker and a 12," 850-watt powered subwoofer.
We hope you enjoyed this brief introduction to the technology
of Intermezzo loudspeakers.If you would like to further explore
their technology and design,please ask your Infinity dealer
for the C.M.M.D.and R.A.B.O.S.White Papers.The White
Papers can also be downloaded from Infinity’s Web site at
www.infinitysystems.com.
TECHNOLOGY
Unpacking the Product
Finish unpacking the speakers and check the contents.If you
suspect damage from transit,report it immediately to your
dealer and/or delivery service.Keep the shipping carton and
packing materials for future use.
Included Accessories ...
Grilles (2)
AC Cord
R.A.B.O.S.Kit (1)
Sound-Level Meter R.A.B.O.S.Test CD
Graph Templates Bandwidth Selector
Adjustment Key
Power
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10
-11
-13
-15
-18
U-R
Batt
2
INTERMEZZO 2.6
Bolts (for use with optional wall-mounting bracket)
Decorative
Side Panels
(2)
3
INTERMEZZO 2.6
The Infinity Intermezzo 2.6 is designed to offer excellent
performance in any listening room or home-theater system.
However,the following placement guidelines and suggestions will
start you on your way to achieving optimum performance.
Remember,these are guidelines.We suggest you experiment with
positioning the loudspeakers to determine their ideal placement
in your particular listening room.
Note:Each speaker may be placed as either the right or left
channel.Their performance will be identical.
2-Channel or Front Left and Front Right
in a Home-Theater System
Generally,the system should be placed at least three feet away
from the side walls.The Intermezzo 2.6 should be placed on
strong,rigid speaker stands that place the tweeter at ear level.
In 2-channel applications,the two speakers should be equidistant
from your primary listening position.We recommend that the
angle formed between the speakers and the listening area be
between 45° and 60°. For example,if the speakers are 8' apart,
your listening position should be 8' to 12' from each speaker.
See Figure 1.With wider speaker separations,it may be
advantageous to slightly angle the speakers,aiming them
toward the listening area.
When used as part of a home-theater system,you may find that
you achieve excellent performance with the left and right
speakers spread apart even further.Feel free to experiment with
the placement of the speakers to achieve the best possible sound
in your listening room.
Surround Channels in a Home-Theater System
When used as part of a Dolby* ProLogic*,THX
®
,or discrete 5.1
channel home-theater system,the surround speakers should be
placed at the sides of,and directed toward,the main listening
area.See Figure 2.If there are several rows of seating,place the
speakers,as described above,perpendicular to,or slightly
behind,the last row of seating.
When used as part of a 7-channel music or home-theater system,
place the side speakers at the sides of and directed toward the
main listening area.If there are several rows of seating,place
the speakers,as described above,perpendicular to the middle
row of seating.The rear speakers should be placed along the
rear wall facing the front of the room.Each rear speaker should
be about 1/3 of the way into the room,but never to the outside of
the listening area.See Figure 3.
As mentioned earlier,the Intermezzo 2.6 offers several ways to
fine-tune the system for optimum performance in any listening
room.These techniques,as well as Infinity’s exclusive R.A.B.O.S.
system,will be discussed in detail later in this manual.
PLACEMENT
SOFA
LEFT
SURROUND
RIGHT
SURROUND
TV
FRONT
LEFT
FRONT
RIGHT
CENTER
SOFA
FRONT
LEFT
LEFT
SIDE
REAR
LEFT
FRONT
RIGHT
RIGHT
SIDE
REAR
RIGHT
TV
CENTER
SOFA
LEFT
CHANNEL
RIGHT
CHANNEL
FIGURE 1
FIGURE 2
FIGURE 3
6
Woofer Level Control
R.A.B.O.S.Controls
7
Center-Frequency Adjustment
8
R.A.B.O.S.Level
9
Bandwidth Adjustment
120V – 60 HZ 6A
+
INPUTS
POWER
1
2
3
4
5
ON
SHELF STAND
HIGH-PASS
FILTER
PLACEMENT
CAUTION!
For continued protection
against risk of fire, replace
only with same type fuse
and rating
ATTENTION!
Utilizer un fusible de
recharge de meme
type et calibre
AC FUSE
3A 120V
OFF
6
9
8
7
F
L
W
¢
›
CONTROLS AND CONNECTIONS
Rear Panel
Front Panel
4
INTERMEZZO 2.6
1
High-Pass Filter
2
Placement Selector
3
Speaker Input
4
Power Switch
5
AC-Cord Input
5
INTERMEZZO 2.6
120V – 60 HZ 6A
+
POWER
ON OFF
SHELF STAND
HIGH-PASS
FILTER
PLACEMENT
AC FUSE
3A 120V
(One Channel Shown)
Amplifier/Receiver
Speaker Outputs
+
BLACK =
NO STRIPE =
STRIPE =
+
RED =
+
1. LOOSEN TERMINALS
2. INSERT BARE END;
TIGHTEN TERMINALS
CAUTION!
For continued protection
against risk of fire, replace
only with same type fuse
and rating
ATTENTION!
Utilizer un fusible de
recharge de meme
type et calibre
+ –
INPUTS
CORD
Placement Selector
2
This control optimizes the performance of the Intermezzo 2.6
based on whether it is placed on a speaker stand or on a shelf.
If you place the Intermezzo 2.6 on a shelf or inside a wall
unit/entertainment center,set this control to “Shelf.
If you place the Intermezzo 2.6 on a floor stand,set the
control to “Stand.
High-Pass Filter
1
When set to “On,this control limits the low frequencies that the
Intermezzo 2.6 will reproduce and allows you to use your
processor’s/receiver’s bass-management settings for an ideal
blend with a subwoofer.
When set to “Off,the Intermezzo 2.6 will reproduce the entire
frequency range.Use this setting only if your system does not
include a subwoofer.
Infinity R.A.B.O.S.is a simple-to-use,yet sophisticated,low-
frequency calibration system.It is designed to work in
conjunction with Infinity Intermezzo self-amplified woofers.Each
woofer contains a parametric equalizer that you will adjust as
indicated by the R.A.B.O.S.test results.Following these
instructions,you will optimize the loudspeakers’response
characteristics to complement their environment.This will
dramatically improve the sound of your system.The optimization
process takes less than 30 minutes.
The R.A.B.O.S.Kit Includes
the Following Components:
• Specialized Sound-Level Meter
• Test CD
• Instructions
• Measurement Templates
• Width Selector
• Adjustment “Key”
What R.A.B.O.S.Does
The Test CD provides specially designed signals you will use
while performing measurements.The sound-level meter provided
is used to “acquire”the information needed for adjustments.You
will create a response plot on the Measurement Template.Using
the Width Selector,you will then determine the appropriate
equalizer settings.The “Key”is used to adjust the parametric
equalizer built into each Intermezzo woofer.After adjustment,the
test sequence is repeated to confirm your settings.
The R.A.B.O.S.Goal
It is a fact of audio that what we hear at low frequencies is
determined as much or more by the listening room than by the
loudspeaker itself.Placement of the loudspeakers and listeners
and the acoustical characteristics of the room surfaces are all
important determinants of bass quantity and quality.In most
practical situations,there is little that can be done about this,
except for patient trial-and-error repositioning of the
loudspeakers and listeners.Usually,the practical constraints of a
living space and the impracticality of massive acoustical
treatment mean that equalization is the only practical solution.
Professional sound engineers routinely employ sophisticated
measurement systems and equalizers to optimize speakers to the
installation.This has never before been practical for the home
audiophile.That’s why R.A.B.O.S.was created.R.A.B.O.S.enables
you to identify the dominant low-frequency response characteristic
of your room.Once you know the problem,R.A.B.O.S.provides the
tools needed to optimize the low-frequency characteristics of the
speakers to the room they are in,exactly as the professional
sound engineers do it.
Performing R.A.B.O.S.Tests
These instructions assume you have already installed your
speakers according to the information provided in the Owner’s
Guide.It is also assumed that all equipment in your entertain-
ment system is interconnected properly and is in good
operating condition.
Preparations
Before beginning R.A.B.O.S.tests,please check the following:
• Make sure all three R.A.B.O.S.controls on the Intermezzo 2.6
are turned fully clockwise.
• Make sure the loudness contour (if any) on your receiver/
processor/preamp is turned off.
• Set the tone controls (Bass and Treble) to their center or
flat positions.
• Bypass all surround and effects features of your receiver/
processor/preamp or set to Stereo Bypass.
• If you are using a multichannel surround processor or
receiver,make sure all bass-management features are properly
set.The Audio channels should all be set to “Small”or “High-
Pass”and the woofer set to “On.
You must have a CD player in the system.A CD player remote
control is quite convenient but not essential.
For best results,it is recommended that all major furnishings
are in place and that all doors and windows in the listening area
are in their normal positions.That is,if you normally listen to
music with all doors closed,then this is how they should be
during this procedure.
Try to minimize ambient noise while running tests.Turn off all
major appliances and any air conditioning or furnace fans.These
can create significant subsonic noise that may be barely
perceptible but which can wreak havoc on low-frequency
measurements.
Critical information is highlighted with this mark:
Helpful hints are marked with this symbol:
ROOM ADAPTIVE BASS OPTIMIZATION SYSTEM
6
INTERMEZZO 2.6
7
INTERMEZZO 2.6
Power is switched on or off by pressing the button directly below
the bar-graph window.When the unit is on,one or more LEDs will
always be illuminated.The function of the LEDs is described in the
following section.
• Power-On/Low Signal: This is indicated by the illumination of
any LED on the bar graph.If the sound level in the room is below
the measurement range of the instrument,a green LED near the
bottom of the bar graph will be illuminated.
• Normal Measurements:When the sound level is within the
range of the RSLM,the green LED will be off and one of the red
LEDs in the bar graph will be illuminated,indicating the relative
sound level,in decibels (dB).
• Over-Range:If the sound level exceeds the range of the meter,
0dB through -5 will all light simultaneously.
• Low Battery:When the battery voltage is too low for accurate
measurements,an LED at the bottom of the bar graph will be
illuminated.Replace the battery.
Do not attempt measurements when this light is on.
RSLM Placement
Determine where in the room you are most likely to sit when
listening to music or watching a movie.This is where you will
want to hold the RSLM during measurements.The RSLM should
be oriented so it can be easily read and held at your seated ear
level during tests.
You must use this same position for all tests.
The RSLM can be mounted on a standard camera tripod.
This will ensure the best results.
Tracks 53–62 of the R.A.B.O.S.Test CD are test tones that can be
used for general diagnostics of your system.They are not used
for R.A.B.O.S.settings.
THE R.A.B.O.S.SOUND-LEVEL METER (RSLM)
The RSLM is a battery-operated,handheld,acoustic measurement
device specifically designed for Infinity R.A.B.O.S.On the face of
the instrument is a light-emitting diode (LED) bar graph that
indicates relative sound level.There are also indicators for
power-on,out-of-range signals and a low battery.
Track Title
1 Welcome
2 Set System Test Level
3 Set Subwoofer Test Level
4 100Hz Test
5 95Hz Test
6 90Hz Test
7 85Hz Test
8 80Hz Test
9 77Hz Test
10 72Hz Test
11 66Hz Test
12 63Hz Test
13 56Hz Test
14 52Hz Test
15 49Hz Test
16 46Hz Test
17 43Hz Test
18 40Hz Test
19 38Hz Test
20 35Hz Test
21 30Hz Test
22 26Hz Test
23 24Hz Test
24 22Hz Test
25 21Hz Test
26 20Hz Test
27 Intro to Quick Retest
28 Quick Retest 100Hz
29 Quick Retest 95Hz
30 Quick Retest 90Hz
31 Quick Retest 85Hz
Track Title
32 Quick Retest 80Hz
33 Quick Retest 77Hz
34 Quick Retest 72Hz
35 Quick Retest 66Hz
36 Quick Retest 63Hz
37 Quick Retest 56Hz
38 Quick Retest 52Hz
39 Quick Retest 49Hz
40 Quick Retest 46Hz
41 Quick Retest 43Hz
42 Quick Retest 40Hz
43 Quick Retest 38Hz
44 Quick Retest 35Hz
45 Quick Retest 30Hz
46 Quick Retest 26Hz
47 Quick Retest 24Hz
48 Quick Retest 22Hz
49 Quick Retest 21Hz
50 Quick Retest 20Hz
51 Final System Level Adjustment
52 Final Subwoofer Level Adjustment
53 Wide Band Pink Noise,Left
54 Wide Band Pink Noise,L+R
55 Wide Band Pink Noise,Right
56 Wide Band Pink Noise,L-R
57 Wide Band Pink Noise,Uncorrelated
58 1 to 4kHz Pink Noise,Left
59 1 to 4kHz Pink Noise,L+R
60 1 to 4kHz Pink Noise,Right
61 1 to 4kHz Pink Noise,Left-R
62 1 to 4kHz Pink Noise,Uncorrelated
FIGURE 4
R.A.B.O.S.Sound-Level Meter
Power
-1
-2
-3
-4
-5
-6
-7
-8
-9
-10
-11
-13
-15
-18
U-R
Batt
FIGURE 5
RSLM bar-graph indications
Contents of the R.A.B.O.S.Test CD
On
Under-range
Measurement
In-range
Over-range
Low
Battery
Initial System-Level Setting
The following steps will set the playback level of the system to
the correct level for all tests that follow.
Turn the system volume to minimum.
Cue the R.A.B.O.S.Test CD to Track 2 and press Pause II.This
track will produce band-limited pink noise in both the left and
right channels.
Press Play . With the RSLM positioned as described above,
increase the system volume until the RSLM display indicates -10dB.
See Figure 6.
RSLM indicating the correct system
level to begin tests (-10dB)
When you have completed this
adjustment,press Pause II.
Setting the Woofer Test Level
Each of the following test tracks is about one minute
long.This is normally much longer than required.Press Pause II
or advance to the next test as soon as you are ready.
This step will set the woofer levels for measurement purposes.
The objective is to scale the woofers’output to make full use of
the RSLM indicator range.Scaling is optimum when a 0dB
reading is observed on the highest peak without triggering the
over-range indication.Later,you will rebalance the woofers to the
main speakers.
The Intermezzo 2.6 should be shipped with the three
R.A.B.O.S.controls,7,8,9,set to fully clockwise positions,
and all measurements should be conducted with their level
controls in this position.Confirm this setting before you begin this
test.The level control 6 should be set to the mid position (5).
Cue Track 3 and Pause II.Track 3 continuously steps through all
woofer test tones for approximately 1 minute.Each tone will play
just long enough for the RSLM to give a stable reading.
To get accurate measurements,it is necessary to play
the woofers quite loud.The 0dB indication is about 94dB.If you
hear a buzz or rattle during this test,it is highly recommended
that you locate the source and eliminate its effects.This is
actually a valuable room-diagnostic tool.
Press Play .As Track 3 plays,watch the RSLM carefully.Watch
for peak readings.The peak reading may be no more than a brief
flash.Readjust the woofer’s level control 6 until the peak level
observed is 0dB without triggering the over-range indication.
See Figure 7.
When finished,press Pause II.
Performing Low-Frequency Measurements
Read the following instructions fully before beginning
tests.
For the following steps,you will need a Measurement Template
and a pencil.
FIGURE 8
R.A.B.O.S. Measurement Template
FIGURE 6
FIGURE 7
Adjusting the woofer levels for a 0dB peak
8
INTERMEZZO 2.6
9
INTERMEZZO 2.6
Each of the following tracks produces a low-frequency test tone.
The range of these tests is from 100Hz down to 20Hz.The
frequency of each test is announced before it begins.The first
test is the highest frequency (100Hz);therefore,you will be
marking the template from right to left.Each frequency point is
listed across the bottom of the Measurement Template (this is
called the X-axis).See Figure 8 on the previous page.The
vertical scale on the left side of the template indicates relative
level,in dBs (the Y-axis).The template’s vertical scale matches
that of the RSLM bar graph.
Cue Track 4 and Pause II.
From now on,you will want to keep your CD player’s
remote control handy.
Press Play .As Track 4 plays,observe the level indicated on
the RSLM.
EXAMPLE:The test frequency is 100Hz and the level indicated is
-2dB.Find the intersection of 100Hz (X-axis) and -2dB (Y-axis).
Place a dot at that point.See Figure 9.
It takes a few seconds for the RSLM reading to stabilize,
especially at very low frequencies.Don’t rush.Give each test
adequate time for the meter to stabilize.
At the bottom of the bar graph is a green “ON”LED.This LED is
illuminated whenever the sound level is below the measuring
range of the RSLM.If this occurs during a test,place a dot at the
intersection of the test frequency and the bottom frame of the
template.See Figure 10.
When finished,press Skip to advance to the next test.
Repeat the process described above for Tracks 5 through 26.
When you have completed the 23 measurements,you are ready to
analyze the data and make corrective adjustments.The completed
Measurement Template will look something like the example in
Figure 11.
Now connect the dots as shown in Figure 12.
This will make interpretation of the data much easier.
FIGURE 9
Locating a test point
2
FIGURE 10
Indicating an under-range test
FIGURE 11
Completed R.A.B.O.S.template
FIGURE 12
Test example with dots connected
What Does a Parametric Equalizer Do?
The R.A.B.O.S.system uses one band of parametric equalization
for response correction.Parametric equalizers are the most
versatile class of filters.The effect an equalizer will have on the
signal is dependent on three parameters.
Frequency:The equalizer will have maximum effect at one
frequency,usually described as the center frequency.
Level:This refers to the amount of cut (in dBs) the equalizer
is set for.
Bandwidth: Defines the range of frequencies over which the
equalizer will have an effect.This adjustment is abbreviated
as “Width.
Only parametric equalizers allow independent adjustment of all
three parameters.
These will be explained more fully in the sections that follow.
Completing the Measurement Template
Along the bottom of the Measurement Template are three fields
where you will enter the equalizer settings needed to complete
system optimization.
These instructions are based on the example in Figure 12.Use
this tutorial to become familiar with the process.Strategies for
several other test results will be presented later.After you have
completed these three entry fields,you will be ready to perform
the adjustments,completing R.A.B.O.S.optimization.
Frequency
The frequency of the R.A.B.O.S.equalizer may be adjusted to
any one of nineteen frequencies from 20Hz to 80Hz.This defines
where you are going to apply equalization.
Width
The frequency range of the R.A.B.O.S.equalizer may be set from
5% to 50% of an octave in 21 steps.This setting defines
how much of the woofers’output will be equalized.
Width is expressed as a percentage of an octave.For example,a
width setting of 25 percent means the equalizer will affect a
frequency band of 1/4 of an octave:1/8 of an octave above and
1/8 of an octave below the center frequency.
The octave is a logarithmic expression.From any point
in the spectrum,one octave above or below that point is always
double or half the frequency.Therefore,one octave above 100Hz
would be 200Hz.One octave below 100Hz is 50Hz.
In the section that follows,we will discuss the use of the
Width Selector.
FIGURE 13
Effect of adjustable width
10
INTERMEZZO 2.6
Using the Width Selector
Read the following instructions carefully.The example
presented may not look like the graph you just created.
Focus on the concepts and techniques presented.Specific
cases will be discussed later.
You will use the Measurement Template just completed and the
Width Selector to determine the correct width setting.The Width
Selector graphically depicts a single resonant peak.The peak
looks similar to a slice of a pie.See Figure 14.At the top of the
Selector is a pull tab.When you slide the tab up and down,the
width of the pie slice becomes narrower and wider,respectively.
The pointers on the sides of the button point to the bandwidth
that corresponds to the width of the slice.
Place the Width Selector over the Measurement Template,
positioning the center rivet of the Selector over the response
peak,as shown in Figure 15.Be sure to align the horizontal lines
of the Width Selector with those of the Measurement Template.
Apply pressure to the upper and lower left corners of the
Selector using the thumb and forefinger of your left hand.Now
gently slide the tab up or down until the adjustable slice most
closely fits the response data.See Figure 16.
FIGURE 14
Width Selector
FIGURE 15
Placement of the
Bandwidth Selector
FIGURE 16
Selector adjusted for
the “best fit”
11
INTERMEZZO 2.6
The pointer on the slider will indicate the correct width setting.
Enter this number in the Width field of the Measurement Template.
In our example,the width is 12.5%.
It is not realistic to expect a perfect fit.Acoustic
measurements encompass the behavior of not only the speakers
but of the room and its contents as well.Reflected energy,
standing waves and ambient noise all add their part.Determining
the best width setting nearly always requires compromise.
Level
This setting will define the amount (level) you want to reduce the
peak,in decibels.
The R.A.B.O.S.level adjustment is limited to attenuation only,and
is adjustable from 0dB to -14dB.After optimization,the R.A.B.O.S.
equalizer will eliminate the largest low-frequency peak;
therefore,the broadband bass level can be increased without
overpowering the midrange frequencies.R.A.B.O.S.applies this
compensation automatically.
You will use the Width Selector as an aid in determining the
correct level setting.Place the Width Selector as described
above and adjust it to the correct width.Observe the first
frequency point on the high-frequency side of the peak that no
longer follows the slope of the Width Selector.In this example
this is 56Hz.Calculate the average level of the readings from
56Hz up to 100Hz;that is,10 data points in this example.
Whenever your answer has a remainder,always round down
(disregarding the negative [-]) to the next whole number.
In our example,you would enter 9 in the attenuation field.
This may not be the best method in all cases.The next section
contains several other examples.
What You Measure,What To Do
As stated earlier,it is not possible to anticipate the effect of
every possible listening environment.However,most residential
sound rooms share many characteristics,and their dimensions
fall into a range that make some response irregularities far more
likely than others.On the following pages are examples of what
you may encounter.Following each example is a strategy for
correction.Compare your measurement results with the following
examples.Find the one that best fits your graph and follow the
instructions presented for that scenario.
Remember,when looking for a match,look at the
descriptive characteristics,not any specific frequency or level.
Each of these examples can occur at any frequency,bandwidth
and level.It is unlikely that your test results will be exactly as
depicted in these examples.
Example 1. Single Dominant Peak:
This is the most common result of speaker/room interaction.
Apply the Width Selector as described in Figure 15.Align the
center-line of the Selector over the center of the peak,as shown in
Figure 16.Now adjust the Selector until you have achieved the “best
fit.The slider now points to the correct bandwidth setting.In this
example,the frequency is 43Hz and the best-fit width is 12.5%.Fill
in the Width and Frequency fields provided on the template.
Determine the appropriate level using the technique described
earlier.In this example,-9dB would be best.Enter the level in the
field provided.
Skip to the “Adjusting the R.A.B.O.S.Equalizer”
section on page 15.
FIGURE 17
Single dominant peak
56Hz 63Hz 66Hz 72Hz 77Hz 80Hz 85Hz 90Hz 95Hz 100Hz
-9 -10 -8 -9 -10 -9 -8 -10 -10 -9 -
92 ÷ 10 = -9.2
12
INTERMEZZO 2.6
13
INTERMEZZO 2.6
Example 2.Two Response Peaks:
Characterized by two response peaks,approximately equal in
amplitude and width.This requires that you make a choice
between the two peaks.In situations like this,the higher
frequency peak will always be more audible and objectionable.
Response peaks below 45Hz,unless extreme,can actually be
beneficial toward achieving visceral impact.Perform corrections
on the upper frequency peak.
Apply the Width Selector as described above.Align the center-line
of the Selector over the center of the higher frequency peak.Now
adjust the Selector until you have achieved the “best fit.The slider
now points to the correct width setting.In this example,this is at
52Hz.The best-fit width is 28%.Fill in the Width and Frequency
fields provided on the template.
Determine the appropriate level using the technique described
earlier.This calculation will indicate a -8dB setting.However,this
peak does not reach the 0dB level as the lower peak does.
Therefore,a -8dB setting would be excessive.The 52Hz peak
stops at -2dB.Subtracting 2 from 8 yields the correct setting,
-6dB.Enter -6 in the Level field.
Skip to the “Adjusting the R.A.B.O.S.Equalizer”section on page 15.
Example 3.Peak Adjacent to a Dip:
Response dips can occur at any frequency,sometimes
immediately adjacent to the peak you want to correct.Two
examples are shown,one immediately above and one immediately
below the peak.Deep response dips such as these are caused by
destructive wave interference.Destructive interference dips occur
only in one spot within the room.It is not uncommon to completely
eliminate the effect by moving the RSLM to a different location.
Note that this does not eliminate the dips.We have simply moved
away from them.Sometimes only a few inches are required.
Do not attempt to correct this condition with equalization.
If you encounter dips like this,take the following steps:
FIGURE 18
Two response peaks
FIGURE 19
Dip above or below peak
1.Select a new test position:Cue the test track corresponding to
the center frequency of the dip.In the first example in Figure 19,
you would play Track 13 (56Hz).Press Play .You will see a
reading very close to what you had before.Now,slowly move the
RSLM around the area,if possible remaining within about a foot
of the original test point.As you move the RSLM,watch the bar
graph.You will observe large level fluctuations.Find a position
that restores the level to approximately that of the adjacent test
points.You may find it helpful to move the RSLM vertically.Dips
can be oriented in any axis.The position that restores the level to
about that of the adjacent test points is your new test position.
2.Reset the test level:Return to the section “Setting the Woofer
Test Level”on page 8.Perform the procedure as described.
3.Repeat the measurements:Now that you are familiar with the
measurement process,you can go much faster by using Tracks
27–50.These tracks contain all the test tones necessary for
measurement.However,each test is only about three seconds,and
there is no frequency announcement.The first test is 100Hz.Just
place each test mark in order until finished.Connect the dots.
Your second measurement will no longer exhibit the deep
response dip.However,the peak will still be evident.Without the
influence of the response dip,the amplitude and center of the
peak may have changed.Compare your new data to the examples
given in this section of the manual.Follow the instructions for
the example that most closely matches your new measurement.
Example 4. Narrow Response:
Although it looks as though this speaker is quite bass-deficient,
this is actually indicative of a single,very narrow peak in excess
of 10dB high.
Apply the Width Selector as described above.Align the center-line
of the Selector over the center of the peak,as shown in Figure
15.Now adjust the Selector until you have achieved the “best fit”.
The slider now points to the correct width setting.In this example,
the frequency is 40Hz and the best-fit width is 10 percent.Fill in
the Width and Frequency fields provided on the template.
Determine the appropriate level using the technique described
earlier.In this example,-13dB is indicated.Enter 13 in the
field provided.
Skip to the “Adjusting the R.A.B.O.S.Equalizer”section on page 15.
Example 5. One or More Narrow Dips:
Response dips can occur at any frequency,sometimes
immediately adjacent to the peak you want to correct.In this
example,there are two such dips on either side of the peak.Deep
response dips such as these are caused by destructive wave
interference.Destructive interference dips occur only in one spot
within the room.It is not uncommon to completely eliminate their
effect by moving the RSLM to a different location.Note that this
does not eliminate the dips.We have simply moved away from
them.Sometimes only a few inches are required.Do not attempt
to correct this condition with equalization.If you encounter dips
like this,take the following steps:
FIGURE 20
Narrow Response
FIGURE 21
Example of two narrow dips
14
INTERMEZZO 2.6
15
INTERMEZZO 2.6
1.Select a new test position:Cue the test track corresponding to
the center frequency of the dip.In the example in Figure 21 you
would play Tracks 14 (52Hz) and 18 (40Hz).Press Play
.You
will see a reading very close to what you had before.Now,slowly
move the RSLM around the area,if possible remaining within
about a foot of the original test point.As you move the RSLM,
watch the bar graph.You will observe large level fluctuations.
Find a location for the speaker or a test location that raises the
response at these frequencies.You may find it helpful to move
the RSLM vertically.Dips can be oriented in any axis.The position
that restores the level to about that of the adjacent test points is
your new test position.
2.Reset the test level:Return to the section “Setting the Woofer
Test Level”on page 8.Perform the procedure as described.er until
finished.Connect the dots.
3. Repeat the measurements:Now that you are familiar with the
measurement process,you can go much faster by using Tracks
27–50.These tracks contain all the test tones necessary for
measurement.However,each test is only about three seconds,and
there is no frequency announcement.The first test is 100Hz.Just
place each test mark in order until finished.Connect the dots.
Your second measurement will no longer exhibit the deep
response dips.However,the peak will still be evident.Without
the influence of the response dips,the amplitude and center
of the peak may have changed.
4.Interpret the new data:Compare your new data to the examples
given in this section of the manual.Follow the instructions for
the example that most closely matches your new measurement.
Example 6. Ideal Response:
If your test data looks similar to the example in Figure 22,you
have a very favorable setup.Skip to the “Final System Balance”
section,page 16.
Adjusting the R.A.B.O.S.Equalizer
Now that you have performed the measurements and interpreted
the data,you have the information needed to adjust the woofer
equalizers.
There are three equalizer adjustments on each speaker.Left
to right,they are marked “F” (frequency),“L (level) and “W”
(width).Each control has 21 positions.These are numbered
from left to right.Therefore, Position 1 is the full counter-
clockwise position.The following table illustrates all switch
positions.
FIGURE 22
Ideal response,no EQ needed
Position F (Hz) L (dB) W
1 CCW 20 -14.1 4.5%
2 20 -13.9 5%
3 20 -13.5 7.5%
4 21 -13.1 10%
5 22 -12.7 12.5%
6 24 -11.7 16.5%
7 26 -11.0 20.5%
8 30 -10.2 23%
9 35 -9.5 26%
10 38 -8.9 28%
11 40 -8.3 29.5%
12 43 -7.9 31%
13 46 -6.4 34%
14 49 -4.4 39%
15 52 -2.9 41.5%
16 56 -1.9 43.5%
17 63 -1.1 45%
18 66 -0.5 46.5%
19 72 0.0 48%
20 77 0.0 49%
21 CW 80 0.0 49.5%
The Intermezzo 2.6 may be cleaned using a soft cloth,dampened
with water only,to remove fingerprints or to wipe off dust.
The grille may be gently vacuumed.Stains may be removed with
an aerosol cleaner,following its instructions.Do not use any
solvents on the grille.
All wiring connections should be inspected and cleaned or
remade periodically.The frequency of maintenance depends on
the metals involved in the connections,atmospheric conditions,
and other factors,but once per year is the minimum.
If a problem occurs,make sure that all connections are properly
made and clean.If a problem exists in one loudspeaker,reverse
the connection wires to the left and right system.If the problem
remains in the same speaker,then the fault is with the loud-
speaker.If the problem appears in the opposite speaker,the
cause is in another component or cable.In the event that your
Intermezzo 2.6 loudspeaker system ever needs service,contact
your local Infinity dealer or Infinity directly at 1-800-553-3332
or www.infinitysystems.com.
MAINTENANCE AND SERVICE
You must use the R.A.B.O.S.key to adjust these controls.Always
adjust both woofers together.Using the adjustment key,adjust the
controls as indicated by the Measurement Template.Each value
shown in the table is represented by detents in the R.A.B.O.S.
controls.Simply count the number of detents necessary,
indicated by the results of your R.A.B.O.S.Test.
Intermezzo 2.6 R.A.B.O.S.Controls
After performing these adjustments,you may skip forward to
the “Final System Balance”section.It is recommended that you
perform a second measurement to confirm that the settings
are correct.
If you are going to retest the system after EQ adjustments,
repeat the “Setting the Woofer Test Level”section on p.8.
Retesting the system will go much faster if you use
Tracks 27–50.These tracks contain all the same test tones you
just used.However,each tone plays for only a few seconds and
there is no frequency announcement.If you are uncomfortable
operating at this pace,you may,of course,perform measure-
ments with the original test tracks.
Your first interpretation of the data and choice of settings may
not be optimum.You can repeat the test-adjust-test cycle as often
as needed to get the desired results.To do this,return to page 8,
“Setting the Woofer Test Level.You may prefer to retest using
the same template.Doing so makes it easy to evaluate
the improvement.
When you are satisfied with the results,go to “Final System
Balance”on this page.
6
9
8
7
F
L
W
¢
›
16
INTERMEZZO 2.6
Final System Balance
Cue Track 51 of the R.A.B.O.S.Test CD.Press Play .Increase
the system volume until the RSLM indicates -10dB.Now play
Track 52.Adjust both woofer gain controls until -10dB is
indicated on the RSLM.Of course,you may fine-tune the gain
control to your listening preference.
This concludes the R.A.B.O.S.process.It is recommended that
you remove the battery from the RSLM.Store the Test CD,Width
Selector, Adjustment Key and the RSLM together.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Infinity INTERMEZZO 2.6 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues