red lion EtherTRAK-2 Quick Start Instructions

Taper
Quick Start Instructions
Phone +1 (877) 432-9908 Quick Start Guide
Fax +1 (717) 764-0839 Sixnet® Series
www.redlion.net Drawing No. LP0995
-1-
EtherTRAK®-2 I/O Modules
Quick Start Instructions
1. Unpack the Red Lion unit and verify the following components are enclosed in the package:
EtherTRAK-2 unit
Quick Start Guide
2. DIN-Rail or panel-mount the module.
3. Connect the 10-30 VDC power supply to the EtherTRAK-2 unit.
Power is supplied to the RTU via the 5-screw terminals.
Device accepts 10-30 VDC power (Power supply / transformer
not included).
4. Install Communications wiring to I/O Module. Make the
necessary Ethernet, USB or RS485 communication
connections between I/O Modules and to your master polling
device.
5. Detach module from the base, configure Network mode and DI
COM Jumper on the base and replace the module.
6. Apply power and observe the status (OK) LED on the unit.
Hardware Status LEDs*.
*See the EtherTRAK-2 User Manual for more information on LEDs.
7. Configure device using the web server or I/O tool kit software.
Application-specific configuration choices may be made by
using the web server embedded with the I/O module or
through the I/O tool kit software.
Access the User Interface
8. Connect PC to the EtherTRAK-2 unit.
a. Connect an Ethernet cable between the local PC and the
unit’s Ethernet 1 port (E1).
b. Verify the link LED is lit.
9. Setup PC IP Address.
Note: For assistance with configuring your PC, see the
appropriate Microsoft Windows support web page listed
at:
http://support.microsoft.com
Signal Screw Terminal Description
Most E2s
E2-
MIX20884-D
only
Power Out Screw #2 Not used
+24 VDC output power on POE
powered Etherbus modules only.
POE power internally supplies
power to module intelligence,
communications, and inputs. A
jumper is required from screw
terminal #2 to screw terminal #6
to power discrete outputs.
Power 2+ Screw #4 Screw #2
Positive power input provides
redundant power for the module
intelligence, communications,
and all inputs and analog outputs.
Power 1+ Screw #6 Screw #4
Positive power connection to
operate all module intelligence,
communication, and all inputs
and output I/O channels.
Return - Screw #8 Screw #6
Power supply negative return -
common to all internal functions
except individually isolated I/O
channels on some modules.
Earth Screw #10 Screw #8
Earth ground connection. Tied to
metal case on Ethernet and USB
connectors on the wiring base.
Phone +1 (877) 432-9908 Quick Start Guide
Fax +1 (717) 764-0839 Sixnet® Series
www.redlion.net Drawing No. LP0995
-2-
PC to Ethernet Interface
10.Select Use the following IP address and fill in the blank fields
with the following information:
Access Web Server Interface
11.Open a web browser and enter the following in the address
bar: 10.1.0.1
12.Upon successfully typing in the IP Address in you will see the
home screen.
You are now connected to the web server interface.
13.In the Ethernet Configuration screen, enter your desired IP
address and subnet mask, or enable DHCP.
Click on commit changes to save these new settings to the I/O
module.
14.Repeat step 10 to return your PC to its original IP address
and subnet mask.
15.Test the I/O module using the Test I/O window to verify proper
I/O operation. Refer to the I/O Toolkit or web server on-line
Help for further instructions.
16.Please refer, for additional information as needed, to the
EtherTRAK-2 User Manual and the E2 Quick Connect Guide
at:
www.redlion.net/sixnet_documentation.
Red Lion Technical Support
If you have followed all instructions up to this point and your unit
is still not communicating, then it is time to contact Red Lion
Technical Support at
[email protected] or 1-877-432-9908
and we will be happy to assist in getting your unit operational.
Installation and Hazardous Area Warnings
These products should not be used to replace proper safety
interlocking. No software-based device (or any other solid-state
device) should ever be designed to be responsible for the main-
tenance of consequential equipment or personnel safety. In par-
ticular, Red Lion disclaims any responsibility for damages, either
direct or consequential, that result from the use of this equipment
in any application.
All power, input and output (I/O) wiring must be in accordance
with Class I, Division 2 wiring methods and in accordance with
the authority having jurisdiction.
These products are operator interface units to be used within
control panels. These devices are intended for use in Class I,
Division 2, Hazardous Locations, industrial control applications.
The enclosure shall be suitable for the location.
WARNING – EXPLOSION HAZARD – SUBSTITUTION OF
COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS 1, DIVISION
2.
WARNING – EXPLOSION HAZARD DO NOT DISCONNECT
EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE
AREA IS KNOWN TO BE NONHAZARDOUS.
WARNING – EXPLOSION HAZARD WHEN IN HAZARDOUS
LOCATIONS, DISCONNECT POWER BEFORE REPLACING OR
WIRING MODULES.
Avertissements pour Installation et Endroits Dangereux
Ces produits sont des unités d'interface opérateur qui doivent
être utilisés à l'intérieur des panneaux de commande. Ces appa-
reils sont destinés à une utilisation en Classe I, Division 2, zones
dangereuses, applications de contrôle industriel. L'enclos doit
être adapté à l’environnement lieu.
Tout courant, câblage entrée et sortie (I / O) doit être conforme
aux méthodes de câblage à la Classe I, Division 2 et
conformément à l'autorité compétente.
AVERTISSEMENT – RISQUE D’EXPLOSION – LA SUBSTITUTION DE
TOUT COMPOSANT PEUT NUIRE À LA CONFORMITÉ DE CLASSE I,
DIVISION 2.
AVERTISSEMENT – RISQUE D’EXPLOSION – NE DÉBRANCHEZ
PAS L'ÉQUIPEMENT À MOINS QUE L'ALIMENTATION AIT ÉTÉ
COUPÉE OU QUE L’ENVIRONNEMENT EST CONNU POUR ÊTRE
NON DANGEREUX.
AVERTISSEMENT - LORSQUE DANS DES ENDROITS DANGEREUX,
DÉBRANCHEZ LE CORDON D'ALIMENTATION AVANT DE
REMPLACER OU DE BRANCHER LES MODULES.
ATEX Requirements
These products are operator interface units to be used within
control panels. Ensure the enclosure is suitable for the location.
A minimum IP54 rated enclosure is needed for ATEX unless an
equivalent degree of protection is supplied by the location.
Use these products within control panels in hazardous locations.
Do not use Hot-swapping in hazardous locations.
Note: Models E2-16DIAC-D and E2-16DORLY-D are
not ATEX certified.
Conditions of Safe Use as per ATEX
Only use the equipment in an area of not more than pollution
degree 2, as defined in EN/IEC 60664-1.
Install the equipment in an enclosure that provides a degree of
protection not less than IP54 in accordance with IEC 60079-15.
Make provision to prevent the rated voltage from being exceeded
by the transient disturbances of more than 140% of the peak
rated voltage.
Note: For additional information please see the EtherTRAK-2
User Manual.
LAN/ETH1
IP Address 10.1.0.100
Subnet Mask 255.0.0.0
  • Page 1 1
  • Page 2 2

red lion EtherTRAK-2 Quick Start Instructions

Taper
Quick Start Instructions

dans d''autres langues