NAPOLEON NEFI18H Mode d'emploi

Marque: NAPOLEON

Modèle: NEFI18H

Catégorie: Cheminées

Taper: Mode d'emploi

W415-1654 / C / 08.28.18

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.16F

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁ replaces.com •[email protected]

SAFETY INFORMATION

WARNING

If the information in these instructions

are not followed exactly, a ﬁ re may result

causing property damage, personal injury

or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

$10.00

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278

NEFI18H

ELECTRIC LOG SET INSERT

W415-1654 / C / 08.28.18

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 5

1.3 GENERAL INSTRUCTIONS 5

1.4 RATING PLATE INFORMATION 6

1.5 LABEL LOCATION 6

2.0 LOCATING LOG SET 7

2.1 UNPACKING AND TESTING LOG SET 7

2.2 GROUNDING LOG SET 7

3.0 INSTALLATION 8

3.1 LOG SET INSTALLATION 8

3.1.1 INSTALLING LOG SET INTO EXISTING FIREPLACE 8

3.1.2 INSTALLING LOG SET INTO MANTEL 9

3.2 HARD WIRING INSTALLATION 10

4.0 OPERATING INSTRUCTIONS 11

4.1 OPERATING CONTROL PANEL 11

4.2 OPERATING BY REMOTE CONTROL 12

4.3 REMOTE BATTERY INSTALLATION 12

5.0 FINISHING 13

5.1 NEFI18H LOG PLACEMENT 13

5.2 CHARCOAL EMBER PLACEMENT 14

6.0 WIRING DIAGRAM 15

7.0 REPLACEMENT PARTS 16

7.1 NEFI18H OVERVIEW 16

8.0 TROUBLESHOOTING 18

9.0 WARRANTY 19

10.0 NOTES 20

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your municipality

for recycling instructions.

1.0 INTRODUCTION

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed

service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and

other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or

relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

W415-1654 / C / 08.28.18

1.1 DIMENSIONS

4 5/8"

117mm

13 1/2"

343mm

10"

254mm

13"

331mm

18"

457mm

16 9/16"

1 3/8"

421mm

34mm

FRONT VIEW

RIGHT SIDE VIEW TOP VIEW

HARDWIRE JUNCTION BOX

OR POWER CORD

W415-1654 / C / 08.28.18

4.8B

A. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B. The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C. If your appliance does not emit heat, consult the operation section of this manual for further

information.

D. Use with a CSA- or UL-certiﬁ ed surge protector.

E. Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

WARNING

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

1.2 LISTING APPROVALS

This log set has been tested in accordance with the CSA and

UL Standards for ﬁ xed and location-dedicated electric room

appliances in the United States and Canada. If you need

assistance during installation, please contact your local dealer.

NOTE: This log set must be electrically wired and grounded

in accordance with local codes or, in the absence of local

codes, with National Electric Code ANSI/NFPA 70-latest

edition in the United States or the Canadian Electric Code,

CSA C22.1 in Canada.

Model Number

NEFI18H

Description

18" Electric

Logset Insert

Voltage

120V AC

Watts

1500W

Amps

15 AMP Ground-

ed Circuit

Appliance Width

18" (457mm)

Appliance Height

13.5"

(343mm)

Appliance Depth

13" (330mm)

Net Weight

22.5lbs (10.2kg)

Gross Weight

27.6lbs (12.5kg)

1.3 GENERAL INSTRUCTIONS

As with most electronic devices, your new log set has been designed to operate at temperatures between 5°C

(41°F) and 35° C (95°F). During the colder winter months, allow the log set to reach room temperature before

turning it on.

W415-1654 / C / 08.28.18

1.4 RATING PLATE INFORMATION

W385-2143

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 1278 /

HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 1278

FOYER À ÉLECTRIQUE. HOMOLOGUE POUR

INSTALLATION DANS UNE CHAMBRE A

COUCHER, UNE SALLE DE BAIN ET UN STUDIO.

APPROPRIE POUR INSTALLATION DANS UNE

MAISON MOBILE.

ELECTRIC FIREPLACE. SUITABLE FOR

BEDROOM AND BED-SITTING ROOM

INSTALLATION. SUITABLE FOR MOBILE

HOME INSTALLATION.

VOLTAGE: 120 V

AC TENSION: 120VCA

FREQUENCY: 60Hz FRÉQUENCE: 60Hz

POWER: 1500W PUISSANCE: 1500W

DATE CODE: XXXXX CODE DE DATE:

DESIGNED IN NORTH AMERCIA

BY WOLF STEEL LTD.

MADE IN CHINA

FABRIQUE EN CHINE

WOLF STEEL LTD.

24 NAPOLEON ROAD,

BARRIE, ON, L4M 0G8 CANADA

SERIAL NUMBER/NO. DE SERIE:

NEFI18

DESIGN AMERIQUE DE NORD

PAR WOLF STEEL LTD.

MASTER CONTRACT: 161746

CONTRAT-CADRE: 161746

MODEL / MODÈLE:

NEFI18H

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to

the model of the appliance.

For rating plate location, see “LABEL LOCATION” section.

This illustration is for reference only. Refer to the rating plate on the log set for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

1.5 LABEL LOCATION

CAUTION LABEL

(W385-1945)

"DO NOT COVER"

LABEL (W385-1946)

WARNING

LABEL

(W385-1943)

FRONT

RIGHT SIDELEFT SIDE

WARNING LABEL

(W385-1944)

RATING PLATE WITH

SERIAL NUMBER

NEFI18H (W385-2143)

NOTE: Do not use the log set during mobile home transportation.

ATTENTION

LABEL

(W385-2133)

SAMPLE

DARDDARD

S ET AMÉRIET AMÉR

FOYER À ÉLECT

INSTALLATIONTALLATION

COUCHER,CHER

APPROPAPPROP

MAISOMAIS

OLTAGE:LTAGE:

120 VAC

FREQUENCY:QUENCY:

60Hz 60H

OWER

:POWER:

150 150

ATE CODE:

DATE CODE:

GNED IN NORTH AMGNED IN NORTH A

BY WOLF SBY WO

MAM

NADA

DEL / MODÈLE:

MODÈLE:

HARD WIRING

LABEL

(W385-2003)

W415-1654 / C / 08.28.18

WARNING

2.0 LOCATING LOG SET

2.1 UNPACKING AND TESTING LOG SET

Carefully remove the appliance from the box and remove the support brackets. Prior to installing the

appliance, remove all packaging material and test to make sure the appliance operates properly by plugging

the power supply cord into a conveniently located 120V, 15 Amp minimum grounded outlet.

2.2 GROUNDING LOG SET

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

96.1

GROUNDING METHODS

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

This appliance is

or use on 120 volts. The cord has a plug

as shown in (A). An adapter as shown in (C) is available for

connecting three-blade grounding type plugs to two-slot

receptacles. The green grounding plug extending from the

adapter must be connected to a permanent ground such as

a properly grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove

plug from outlet.

NOTE: Must be connected to a dedicated 15 amp circuit.

The use of an extension cord is NOT permitted.

W415-1654 / C / 08.28.18

3.0 INSTALLATION

NOTE: Follow all National and local electrical codes.

WARNING

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

68.5A

Do not install the

log set into a cavity

smaller than that

referenced in the

table.

HEIGHT WIDTH DEPTH

LOG SET A B C

NEFI18H 14"

(356mm)

18"

(472mm)

14"

(356mm)

3.1 LOG SET INSTALLATION

The log set can be installed in any location. It is suggested to install the log set into an existing ﬁ replace or a

wood mantel for aesthetic purposes. When installed, ensure the log set is stable and not apt to tip.

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture, and high

trafﬁ c areas.

3.1.1 INSTALLING LOG SET INTO EXISTING FIREPLACE

MINIMUM FIREPLACE CAVITY SIZE

A. The log set insert must be installed in an opening with the minimum cavity sizes shown below:

NOTE: Seal all chimney drafts with non-combustible materials to prevent any chimney debris from

falling onto the log set. Cap the top of the chimney ﬂ ue to prevent rain from entering.

Plug the log set into an outlet which has a 15Amp, 120V rating. If it is necessary to hard wire the log set, see

"HARD WIRING INSTALLATION" section.

WARNING: Due to the high temperatures, do not use existing ﬁ replace doors which close or seal off

the log set. If installed behind any ﬁ replace door, allow heat to be exhausted. If using existing screens,

the screen must provide adequate airﬂ ow in front of the log set.

B. Place the log set in a position which provides optimum ﬂ ame performance. To achieve ﬂ ame

effect, the log set should be 2" away from the rear wall.

NOTE: Clean ﬁ replace prior to installing log set to prevent debris and/or ash from entering the heater.

W415-1654 / C / 08.28.18

Fig. 2

3.1.2 INSTALLING LOG SET INTO MANTEL

A. Lift the log set up and insert into the opening. Do not push or slide the bottom of the log set on the

ﬂ oor base (Figure 1).

B. Set the log set down and into place (Figure 2).

NOTE : To achieve ﬂ ame effect, the log set should be 2" away from the rear wall.

MANTEL

STEP 3:

SET APPLIANCE

MANTEL

DO NOT SLIDE LOGSET

NE GLISSEZ PAS L'APPAREIL

STEP 1: LIFT

STEP 2: INSERT

NOTE: To prevent damaging the base of the mantel, carefully lift the log set into the mantel while

avoiding contact with the front edge of the mantel base.

Fig. 1

NOTE: To aid with

moving the appliance,

leave enough wire so

that the log set can

be removed from the

enclosure without

disconnecting the

power supply. If

servicing, shut off

power supply.

A. Remove the securing screws (2) from the electrical cover plate, located on the rear of the log set.

B. Add an electrical box connector and feed the supply wires through the 7/8" (22mm) hole.

C. Separate the black, white and green wires that have the wire nuts on them.

D. Remove the wire nuts and secure the black wire (power L1) to the black (power L1) lead of the

power supply. Connect the white wire from the appliance to the white (neutral) wire from the

power supply. Connect the green wire to the ground wire.

E. Resecure the cover plate.

BLACK

WHITE

BLACK

WHITE

GREEN

(L1)

(N)

(G)

WIRE NUT

W415-1654 / C / 08.28.18

BLACK

WHITE

GREEN

BLACK

WHITE

HARD WIRING CONNECTION

If it is necessary to hard wire the appliance, a qualiﬁ ed electrician must remove the cord connection, and wire

directly to the household wiring. The wire and power supply breaker must be rated for 120V and a minimum

of 15 Amps.

This log set must be electrically connected and grounded in accordance with local codes, if hard wired. In

the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the

current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

NOTE: There are 3 wires from the appliance junction; white (neutral), black (power L1) and green

(ground) that connect to 120V power supply (breaker panel), see below.

White, Green and

Black wires:

Connect to 120V

power supply.

3.2 HARD WIRING INSTALLATION

BLACK

WHITE

GREEN

POWER

Turns the appliance ON/OFF.

FLAME & EMBER LIGHT

CONTROL

HEATER CONTROL

TIMER

TEMPERATURE

CONTROL

Controls Flame brightness and the Ember Light.

5 Settings: Flame & Ember off (FO), Ember on but Flame

off (LL), small Flame & Ember (F1), medium Flame &

Ember (F2), brightest Flame and Ember (F3).

Default setting is (F3).

Turns the Heater and Blower ON/OFF.

4 Settings: Heater & Blower off (HO), Blower on (BL), low

heat (H1), high heat (H2).

Default setting is (HO).

Timer can be programed to run appliance for specific

lengths of time (30mins. minimum to 6hrs maximum).

Default setting is Timer de-select.

Press and hold the Timer button for 5 seconds. This

will change the button to Temperature Control, or vice

versa. There are 7 temperature settings (61

°F, 64°F, 70°F,

°F, 81°F, 85°F and OFF).

Default setting is de-select Temperature Control.

F° / C° SWITCH

Hold 5

seconds

To change temperature format, Fahrenheit or Celsius.

Press and hold the Flame button for 5 seconds.

Default setting is Fahrenheit.

HEATER LOCK

Hold 5

seconds

Heater button can be locked or unlocked by holding the

Heater button for 5 seconds.

Default setting is heater unlock

Hold 5

seconds

W415-1654 / C / 08.28.18

4.0 OPERATING INSTRUCTIONS

Once the log set has been plugged into a grounded electrical outlet or hard wired to a dedicated grounded

120V power supply, it is ready to operate.

ATTENTION: Ensure the house circuit breakers for the power supply are turned on. When initially

connecting the appliance into a power source, the appliance will perfom an LED check. The appliance

will ﬂ ash on and off for 5 seconds then remain off until turned on by control panel or remote.

The Control Panel is located on the front of the log set.

4.1 OPERATING CONTROL PANEL

W415-1654 / C / 08.28.18

4.2 OPERATING BY REMOTE CONTROL

WARNING

TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND

CHILDREN. DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY.

KNOT BEFORE THROWING AWAY.

A. The power button can be used to turn the log set on/off. Pressing

this button activates the power to the log set. Pressing the

power button again will turn off the log set. The ember and log will

fade after 4 seconds after turning off the log set.

B. To adjust the ﬂ ame brightness and ember log light, press the ﬂ ame

button . There is one ember log light and three ﬂ ame brightness

levels to cycle through and then an off setting (LL, F1, F2, F3 and

then F0). F3 is the brightest ﬂ ame level, LL is the ember log light

only.

C. To control the thermostat function, press the thermostat

button . There are 7 temperature settings (61°F, 64°F, 70°F, 75°F,

81°F 85°F and off). The default setting will display Fahrenheit. Press

the thermostat button to cycle through the settings. Once you have

selected the desired temperature, the heater will automatically

operate until that temperature is reached. When the room

temperature is 2 degrees lower than the temperature setting, the

heater will turn on.

D. To activate the heater and blower, press the heater button , the

blower will turn on. Press the heater button again to set desired low

or high heat temperature; press the heater button again to turn off

the heater.

E. The timer controls all operating modes of the log set. To activate the

timer, press the timer button , the icon will illuminate and the time will appear on the LED display.

To choose the desired time, continue to press the timer button, there are 8 settings (30mins,1h, 2h,

3h, 4h, 5h, 6h and off). The ﬁ replace will turn off at the setting time.

F. To turn off the log set, press the power button once on the remote, or press the power button once

on the control panel on the appliance.

NOTE: This handheld remote control must remain within 6 meters or 19 feet of the log set to be

effective.

NOTE: When operating the remote control, it must be directed towards the front center of the log set.

4.3 REMOTE BATTERY INSTALLATION

1. To replace the existing battery, remove the battery

holder.

2. To remove the battery holder, turn remote onto

front side and press the left side lever towards the

center while pulling the battery holder out using the

slot provided.

3. Replace existing battery, type CR 2025, with a

new battery and reinstall the battery holder into the

remote by sliding it into position, as shown.

4. Battery cover is secure onto the remote control

when a "CLICKING" noise is heard.

REMOTE

(REAR SIDE)

BATTERY (CR 2025)

BATTERY COVER

W415-1654 / C / 08.28.18

5.0 FINISHING

WARNING

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

Place the log (#3) into the groove. Ensure the log

is secure, as shown.

Place log (#4) into the groove. Ensure the log is

secure, as shown.

5.1 NEFI18H LOG PLACEMENT

3 4

1 2

Place the log (#1) onto the pins. Ensure the log is

secure onto the pins, as shown.

Place the log (#2) onto the pins. Ensure the log is

secure onto the pins, as shown.

W415-1654 / C / 08.28.18

A. Place the charcoal ember around the front and sides of the ﬁ rebox, as indicated on the diagram

below.

Fine dust found in the bottom of the bag should not be used.

NOTE: DO NOT BLOCK AIR INTAKE OPENING AND OUTLET WITH CHARCOAL EMBERS.

CHARCOAL

EMBERS

OUTLET

OPENING

AIR INTAKE

OPENING

5.2 CHARCOAL EMBER PLACEMENT

WARNING

TO AVOID DANGER OF SUFFOCATION, KEEP THE PACKAGING BAG AND CHARCOAL EMBERS

AWAY FROM BABIES AND CHILDREN. DO NOT USE IN CRIBS, BEDS, CARRIAGES OR PLAY PENS.

THE BAG IS NOT A TOY. KNOT BEFORE THROWING AWAY. PREVENT EMBERS FROM BEING

SWALLOWED.

W415-1654 / C / 08.28.18

6.0 WIRING DIAGRAM

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

PLUG /

FICHE

FAN /

SOUFFLERIE

MOTOR /

MOTEUR

CARTE DE CIRCUIT IMPRIMÉ

MAIN PCB BOARD /

WIRE NUT /

CONNECTEUR

DE FILS

WIRE NUT /

CONNECTEUR

DE FILS

WIRE NUT /

CONNECTEUR

DE FILS

HEATER 700W2 /

CHAUFFERETTE 700W2

HEATER 700W1 /

CHAUFFERETTE 700W1

THERMAL CUT-OFF /

COUPURE

THERMIQUE

700W1

700W2

MOTOR /

MOTEUR

FAN /

SOUFFLERIE

T-FUSE /

FUSIBLE

FLAME /

FLAMME

DISPLAY CN3 /

AFFICHAGE

TEMPERATURE

SENSOR /

CAPTEUR DE

EMPÉRATURE

CONTROL PANEL BOARD /

PANNEAU DE CONTRÔLÉ

FLAME LED LIGHT /

LUMIÈRE DEL DE FLAMME

LOG LIGHT /

DEL DES BÛCHES

#1 EMBER BED LIGHT /

#1 LUMIÈRE LIT DE BRAISES

LOG LIGHT /

DEL DES BÛCHES

#2 EMBER BED LIGHT /

#2 LUMIÈRE LIT DE BRAISES

W385-2151

W415-1654 / C / 08.28.18

41.1C

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts

can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE

REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

PARTS, PART NUMBERS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PARTS IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN 2 TO 5 BUSINESS DAYS FOR MOST

DELIVERY DESTINATIONS.

PARTS NOT IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN A 2 TO 4 WEEK PERIOD, FOR

MOST CASES.

PARTS IDENTIFIED AS ‘SO’ ARE SPECIAL ORDER AND CAN TAKE UP TO 90 DAYS FOR DELIVERY.

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE

ONLY

PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

WARNING

For after sales service, please call 1-866-820-8686

7.0 REPLACEMENT PARTS

7.1 NEFI18H OVERVIEW

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

REF. NO.

PART NUMBER DESCRIPTION

BUSHINGS, ROTISSERIEW105-0020-SER

STOCKED

G510-0002-SER PLASTIC BUMPER (4 PCS)

G010-0079-SER HEATER AND BLOWER ASSEMBL

W290-0349-SER RUBBER MOTOR GASKET

SYNCHRONOUS MOTOR

FLAME LED

LED, LOG

HOUSING, LOG LED

CONTROL PANE

W435-0079-SER

W405-0040-SER

G405-0012-SER

W350-0777-SER

G010-0081-SER

REF. NO.

PART NUMBER DESCRIPTION

W135-0623-SER REAR LOG

GRATEW185-0043-SER

STOCKED

W010-3929-SER

REFLECTOR SPINDLE ASSEMBLY

FRONT LOG

TOP LEFT LOG

TOP RIGHT LOG

FLAME COVER

W135-0624-SER

W135-0622-SER

W135-0621-SER

W497-0025-SER

W405-0023-SER EMBER LED

G190-0005-SER PCB BOARD (w/ 4 SPACERS)

G200-0010-SER

HARDWIRE HOUSING COVER

YES

G190-0006-SER CONTROL PANEL PCB

YES

21 W285-0002-SER FUSE 2 Amp YES

W415-1654 / C / 08.28.18

NOTE: Care must be taken when removing and disposing of any broken glass or damaged

components. Be sure to vacuum up any broken glass from inside the appliance before operation.

W415-1654 / C / 08.28.18

8.0 TROUBLESHOOTING

WARNING

TURN OFF THE APPLAINCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A

QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

42.37

SYMPTOM PROBLEM TEST SOLUTION

Dim or no ﬂ ame Flame brightness not selected See “OPERATION” section.

Flame LEDs are burnt out Inspect the LED by selecting different brightness settings and

replace them if necessary.

Main PCB board burnt out Inspect the Main PCB Board and replace if necessary.

Ember bed is not

glowing or dimming

Brightness not selected See “OPERATION” section.

Ember LEDs are burnt out Inspect the ember bed LEDs by selecting different brightness

settings and replace if necessary.

Main PCB board burnt out Inspect the Main PCB board and replace if necessary.

No warm air coming

out of appliance

Heater setting not selected

See “OPERATION” section, heater includes multiple selections such

as blower only, no heat, 750W (low heat), 1500W (high heat).

Heater has been locked out See “OPERATION” section, heater lockout.

Room temperature is higher than the

appliance setting (if it is set to room

temperature)

Reset temperature setting.

Heater has overheated Unplug power or turn off the circuit breaker, allow appliance to

cool for 15 minutes.

Heater is burnt out Inspect the blower and heater and replace it if necessary.

Appliance turns off

and will not turn on

House circuit breaker has tripped Reset house circuit breaker.

Appliance fuse has blown Replace the fuse.

Appliance has overheated and safety

thermal switch has tripped

Unplug power or turn off the circuit breaker, allow appliance to cool

for 15 minutes to reset the thermal switch, then plug in or turn it on.

Appliance will not

come on when switch

is ﬂ ipped to ON

Appliance is not plugged into an

electrical outlet

Check plug and plug it in.

Hard wire connections are not

corr

ect

See “HARD WIRE INSTALLATION” section.

Appliance has overheated and safety

thermal switch has tripped

Unplug power or turn off the circuit breaker, allow appliance to

cool for 15 minutes, then plug in or turn the breaker on.

Circuit board is burnt Inspect circuit board and replace if necessary.

Remote control does

not work

Low batteries Replace batteries in remote control.

Remote receiver malfunction Ensure remote receiver is not blocked. Replace control panel.

Flame does not move Motor stalled/malfunctioned Cycle ON/OFF. If problems persists, consult dealer.

Heater shuts off

automatically

Room is too warm The heater has a built-in thermostat so it will shut off automatically

once the pre-set temperature is reached. It will also turn on

automatically if the room temperature drops below the pre-set

temperature.

LED Flashing Appliance has overheated and safety

thermal switch has tripped

Unplug power or turn off the circuit breaker, allow appliance to

cool for 15 minutes, then plug in or turn the circuit breaker on.

Power Failure Appliance has returned to default

settings

Re-program appliance to original settings.

E1 Error Code

Thermostat wire not connected to PCB

Connect wire.

Thermostat wire connection to PCB

is loose

Connect wire ﬁ rmly to PCB.

Thermostat has failed Replace thermostat.

E2 Error Code Thermostat shorting Replace thermostat.

PCB thermostat connection is

shorting

Replace PCB.

W415-1654 / C / 08.28.18

9.0 WARRANTY

NAPOLEON warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary.

Simply provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON reserves the right to have

its representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an

authorized NAPOLEON dealer, your appliance is subject to the following conditions and limitations:

Warranty coverage begins on the date of original installation.

This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.

Installation must be done in accordance with the installation instructions included with the product and all local and national building and ﬁ re codes.

This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed

from other manufacturers will nullify this warranty.

This limited warranty further does not cover any scratches, dents, corrosion or discolouring caused by excessive heat, abrasive and chemical

cleaners nor chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs.

In the ﬁ rst year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship,

provided that the product has been operated in accordance with the operation instructions and under normal conditions.

NAPOLEON will not be responsible for installation, labour or any other expenses related to the reinstallation of a warranted part, and such

expenses are not covered by this warranty. Notwithstanding any provisions contained in the Limited Warranty, NAPOLEON’s responsibility under

this warranty is deﬁ ned as above, and it shall not in any event extend to any incidental, consequential or indirect damages.

This warranty deﬁ nes the obligations and liability of NAPOLEON with respect to the NAPOLEON electric appliance and any other warranties

expressed or implied with respect to this product; its components or accessories are excluded.

NAPOLEON neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product.

Any damages to appliance, brass trim or other component due to water, weather damage, long periods of dampness, condensation, damaging

chemicals or cleaners will not be the responsibility of NAPOLEON.

The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized

dealer. The warranty registration card must be returned within fourteen days to register the warranty.

NAPOLEON reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.

All parts replaced under the Limited Warranty Policy are subject to a single claim.

All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.

The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned

products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or

replace such defect.

Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without

authorization will be refused and returned to sender.

Shipping costs are not covered under this warranty.

Additional service fees may apply if you are seeking warranty service from a dealer.

2.5D

NAPOLEON electric appliances are manufactured under the strict Standard of the world recognized

ISO 9001 : 2008 Quality Assurance Certiﬁ cate.

NAPOLEON products are designed with superior components and materials and assembled by trained craftsmen who

take great pride in their work. Once assembled the complete appliance is thoroughly inspected by a qualiﬁ ed technician

before packing to ensure that you, the customer, receive the quality product that you expect from NAPOLEON.

Electrical components and wearable parts are covered and NAPOLEON will provide replacement parts free of charge during

the ﬁ rst year of limited warranty. This covers: fan/heaters, motors, switches, nylon bearing components, remote controls and

LED lights.

Any labour related to warranty repair is not covered.

* Construction of models vary. Warranty applies only to components included with your speciﬁ c appliance.

NAPOLEON ELECTRIC APPLIANCE LIMITED WARRANTY

CONDITIONS AND LIMITATIONS

ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS.

NAPOLEON IS A REGISTERED TRADEMARK OF WOLF STEEL LTD.

W415-1654 / C / 08.28.18

10.0 NOTES

44.1

La page est en cours de chargement...

NAPOLEON NEFI18H Mode d'emploi

Marque: NAPOLEON

Modèle: NEFI18H

Catégorie: Cheminées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON NEFI18H User guide

NAPOLEON NEFI18H Mode d'emploi

NAPOLEON NEFI18H Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents