Philips Avent SCF358 Manuel utilisateur

NL Gebruiksaanwijzing 69

TH  86

TR Kullanım kılavuzu 102

VI Hướng dẫn sử dụng 119

EN User manual 2

DE Benutzerhandbuch 18

FR Mode d’emploi 35

ID Buku Petunjuk Pengguna 52

SCF358

2 ENGLISH

Contents

Important 3

Introduction 5

General description 6

Cleaning and descaling 14

Recycling 16

Guarantee and service 16

Troubleshooting 16

3ENGLISH

Important

Read this user manual carefully before you use the appliance and save it for future

reference.

Danger

- Do not immerse the cord, plug or appliance in water or

other liquid.

Warning

- Only use the appliance indoors.

- Do not let the power cord hang over the edge of a table

or worktop. Store excess cord in the base of the bottle

warmer.

- Keep the power cord away from hot surfaces.

- Only connect the appliance to a grounded wall socket.

Always make sure that the plug is inserted into the wall

socket properly.

- Before you connect the appliance, check that the voltage

indicated on the bottom of the appliance corresponds to

the local voltage .

- If you need to use an extension cord, make sure it is

a grounded extension cord with a rating of at least

13 amperes.

- Do not use the appliance if the plug, the power cord

or the appliance itself is damaged. If the power cord is

damaged, you must have it replaced by Philips, a Philips

authorized service centre or similarly qualied persons in

order to avoid a hazard.

- Do not place the appliance on or near a hot gas or

electric cooker, or in a heated oven.

- This appliance can be used by persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved.

4 ENGLISH

- This appliance can be used by children aged from 8

years and above if they have been given supervision or

instruction concerning use of the appliance in a safe way

and if they understand the hazards involved. Cleaning

and user maintenance shall not be made by children

unless they are older than 8 and supervised. Keep the

appliance and its cord out of reach of children aged less

than 8 years.

- Children must not play with the appliance.

- Do not spill water on the power plug.

- Only use the appliance as described in the user manual

to avoid injury due to misuse.

- Do not preheat the appliance.

- Always place a fully assembled bottle with cap in the

bottle warmer before you add water.

- Make sure you add water before you switch on the bottle

warmer.

- Hot water can cause serious burns. Be careful when the

bottle warmer contains hot water.

- The accessible surfaces of the appliance may become

hot during use and are subject to residual heat after use.

- Do not move the appliance when it contains hot water.

- When the food or milk has reached the required

temperature, remove the bottle or container from the

bottle warmer. If you leave food or milk in the bottle

warmer, the temperature of the food or milk increases.

Caution

- This appliance is intended for use in household and

similar applications such as farm houses, bed and

breakfast accommodations, sta kitchen areas in stores,

oces and other work environments, and by guests in

hotels, motels and other residential type environments.

- The food should not be heated for too long.

5ENGLISH

- Always check the food temperature before you feed

your child. Gently swirl the bottle and check by sprinkling

a few drops on the inside of your wrist. (Follow the

instructions in section ‘‘Feed your baby the milk’’.)

- Unplug the appliance when it is not in use.

- The surface of the heating element is subject to residual

heat after use.

- Let the appliance cool down before you clean it.

- Follow the descaling instructions to avoid irreparable

damage.

- Do not try to open or repair the appliance yourself.

Contact the Philips Consumer Care Centre in your

country (see www.philips.com/support).

The production date code YYWW is located in the cord storage compartment in the

base of the bottle warmer.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and regulations

regarding exposure to electromagnetic elds.

Introduction

Congratulations on your purchase and welcome to Philips Avent! To fully benet

from the support that Philips Avent oers, register your product at

www.philips.com/welcome.

With this bottle warmer, you can safely warm and defrost milk in Philips Avent and

other most common branded feeding bottles and baby food in containers.

To help preserve the quality of your breast milk, it is important to warm the milk

in a safe and controlled way. The built-in sensor tracks the temperature to avoid

overheating.

6 ENGLISH

General description

Product overview

A

B

CD

F

E

A Bottle warmer D Keep warm/defrost setting

B Progress indicator E Milk volume setting

C Baby food warming setting F On/o button

7ENGLISH

Explanation of settings

Milk volume

• Select the milk volume you warm. You

can set from 30 ml / 1 oz up to 330 ml /

11 oz. The bottle warmer warms the milk to

approximately body temperature. It then goes

to keep warm mode automatically for about

60 minutes.

Baby food warming

• Select this setting to warm baby food.

Keep warm / defrost

• The built-in sensor detects the milk / baby

food temperature to switch to the optimal

setting. If the milk / baby food is warm, it will

be warmed gradually and kept at the right

temperature. If the milk / baby food is frozen,

it will be defrosted to liquid state and then

warmed to the right temperature.

When the entire progress indicator is on but not ashing, the milk / food is ready

for feeding. Feed your baby when the milk / food is warmed. Do not rewarm the

milk / food after it has cooled down, as bacteria may start to develop in it.

Warm milk

1

Place the bottle in the bottle warmer. Fill with drinking water to the level of

the milk. If you have a large volume of milk, ll with water to approximately

1 cm below the top of the bottle warmer.

2

Select the desired setting based on the milk volume and press the on / o

button to switch on.

7

210

7oz

210ml

8 ENGLISH

3

The progress indicator ashes gradually to show the progress of milk

warming.

4

When the entire progress indicator lights up continuously, the milk is ready

for feeding and the bottle warmer automatically switches to keep warm

mode.

5

The bottle warmer switches o automatically after about 60 minutes,

including warming time. The progress indicator turns o.

60 min

Tip

• If you want the milk warmer, keep the bottle in the appliance until it reaches the desired

temperature after the entire progress indicator lights up.

• If you are using a milk bag, select the keep warm / defrost setting because it takes less

power to warm milk bags.

• If you are using a silicone bottle, it takes longer time to warm milk. Keep it in the bottle

warmer for 3-4 minutes after the entire progress indicator lights up.

Recommended setting for dierent containers

Container Recommended Setting

Plastic Milk volume setting

Glass Milk volume setting

Silicone Milk volume setting + 3-4 minutes

Milk bag Keep warm/ Defrost setting

Check the instructions of your milk bag and make sure it can be warmed in a bottle

warmer.

9ENGLISH

Note

• The time to warm milk depends on the volume, initial temperature and milk bottle

material.

Feed your baby the milk

Press the on / o button to switch o the appliance and take out the milk bottle.

Note

• If you are using a small milk bottle, such as a 2 oz milk bottle, be careful of the hot water

when you take out the bottle.

Always check the temperature of the milk before you feed your baby. Gently swirl

the bottle and check by sprinkling a few drops on the inside of your wrist.

Reuse the bottle warmer right away for another bottle

If you want to warm another bottle, let the bottle warmer cool down for a few

minutes. To speed up, ll the bottle warmer with fresh cold water.

When you switch on the bottle warmer, the progress indicator ashes gradually to

indicate that the appliance is warming again.

Note

• If the progress indicator is on but not ashing, the bottle warmer is still too hot to warm

another bottle. Switch o the bottle warmer and let it cool down for a few minutes.

10 ENGLISH

Warm baby food

1

Place the baby food container in the bottle warmer. Fill with drinking water

to the level of the baby food. If you have a large volume of baby food, ll with

water to approximately 1 cm below the top of the bottle warmer.

2

Select the baby food warming setting and press the on / o button to switch

on.

3

The progress indicator ashes to show it is in the warming process.

Note

• Due to variations in baby food consistency, it is not possible for the appliance to detect

precisely how long the baby food should be warmed.

4

Stir the baby food while the jar or container is in the bottle warmer. For

optimal result, check its temperature while it is warming up.

» Be careful not to burn your ngers when holding the container or jar while

stirring.

11ENGLISH

5

When the entire progress indicator lights up continuously, the baby food

is ready for feeding and the bottle warmer automatically switches to keep

warm mode.

6

The bottle warmer switches o automatically after about 60 minutes,

including warming time. The progress indicator turns o.

60 min

Feed your baby the baby food

Press the on / o button to switch o the appliance and take out the food

container or jar.

Always check the temperature of the baby food before you feed your baby. Gently

stir the baby food in the food container or jar and taste it to make sure it is not

too hot.

12 ENGLISH

Reuse the bottle warmer right away for another container of baby

food

Follow the same steps as indicated in the section “Warm milk”

Keep warm milk

With this setting, the built-in sensor detects the milk temperature to switch to the

optimal setting. If you put warm milk, it is warmed gradually and kept at the right

temperature.

1

Place the bottle in the bottle warmer. Fill with drinking water to the level of

the milk. If you have a large volume of milk, ll with water to approximately

1 cm below the top of the bottle warmer.

2

Select the keep warm / defrost setting and press the on / o button to

switch on.

3

The progress indicator ashes to show that milk is warming.

4

When the entire progress indicator lights up continuously, the milk is ready

for feeding and the bottle warmer keeps the milk at this temperature.

13ENGLISH

5

The bottle warmer switches o automatically after about 60 minutes,

including warming time. The progress indicator turns o.

60 min

Note

• The time may vary depends on the milk volume and starting temperature.

Defrost milk

With this setting, the built-in sensor detects the milk / food temperature to switch

to the optimal setting. If you put frozen milk / baby food, the bottle warmer defrosts

the milk / baby food to liquid state and then warms it to the right temperature.

1

Place the bottle in the bottle warmer. Fill with drinking water to the level of

the milk. If you have a large volume of milk, ll with water to approximately

1 cm below the top of the bottle warmer.

2

Select the keep warm / defrost setting and press the on / o button to

switch on.

14 ENGLISH

3

The progress indicator ashes to show that milk is defrosting and warming.

4

When the entire progress indicator lights up continuously, the milk / baby

food is ready for feeding.

5

The bottle warmer switches o automatically after about 60 minutes,

including defrosting and warming time. The progress indicator turns o.

60 min

You can also defrost baby food in the Philips Avent food container with this

setting. Due to variations in baby food consistency, it is strongly recommended to

continuously stir and check the baby food while you are defrosting it for optimal

result.

Cleaning and descaling

Cleaning

1

Unplug and let it cool down.

2

Pour out water sideways rather than forwards or backwards to keep water

from spilling onto the knob or main plug.

15ENGLISH

3

Wipe with a moist cloth.

» Do not use abrasive, antibacterial cleaning agents, chemical solvents or

sharp tools to clean the bottle warmer.

Note

• If you used the bottle warmer to warm baby food, make sure that no spilled baby food

remains at the bottom of bottle warmer.

Descaling

It is recommended to descale the bottle warmer every four weeks to ensure it

works eciently.

To descale, mix 60 ml / 2 oz of white vinegar with 120 ml / 4oz of cold water. Switch

on and select the milk warming setting for contents under 180 ml / 6 oz and let the

appliance operate for 10 minutes. Leave the solution in the bottle warmer until all

scale has dissolved.

10 min

180ml

6oz

Note

• You can also use citric acid based descalers.

• Do not use other types of descalers.

Empty the bottle warmer and rinse the inside thoroughly. If you still see traces of

scale, repeat the descaling procedure.

16 ENGLISH

Recycling

This symbol means that this product shall not be disposed of with normal

household waste (2012/19/EU).

Follow your country’s rules for the separate collection of electrical and

electronic products. Correct disposal helps prevent negative consequences

for the environment and human health.

Guarantee and service

If you need information or if you have problems, please visit the Philips website

at www. philips. com / avent or contact the Philips Customer Care Center in your

country (refer to the enclosed worldwide guarantee leaet for details). If there is no

Customer Care Center in your country, go to your local Philips dealer.

Troubleshooting

This chapter summarizes the most common problems you could encounter with

the appliance. If you are unable to resolve the problem with the information below,

contact the Consumer Care Center in your country.

Problem After switching on the bottle warmer, the entire progress indicator

blinks fast and switches o.

Cause

•

The temperature of water in the bottle warmer is too hot or too

cold.

•

The boil-dry protection is activated.

Solution

•

Switch o and unplug. Let it cool down for a few minutes. Make

sure you ll it with fresh room temperature water.

•

The bottle warmer automatically switches o if it is on and there

is no water or not enough water in it. Switch o and unplug. Let

it cool down rst. Make sure you ll it with enough fresh room

temperature water. The bottle warmer is ready to use again.

Problem The milk is too hot.

Cause

•

You may have selected an incorrect setting or are using a milk bag.

Solution

•

Select the milk volume setting based on the milk volume, not the

bottle size.

•

If you are using a milk bag, select the keep warm / defrost setting.

17ENGLISH

Problem The milk is still cold.

Cause

•

You may have selected an incorrect setting, are using a silicone

bottle, or have lled the bottle warmer with warm water.

Solution

•

Select the milk volume setting based on the milk volume, not the

bottle size.

•

If you are using a silicone bottle, select the milk volume setting

based on the milk volume. When the entire progress indicator is

on, wait for 3-4 minutes for the milk to warm.

•

Fill the bottle warmer with fresh room temperature water. Do not

use warm water.

Problem After switching on the bottle warmer, the entire progress indicator is

on but not ashing.

Cause

•

The bottle warmer is still too hot to warm another bottle. You may

have just nished warming a bottle. Switch o and let it cool down

for a few minutes.

Solution

•

To speed up, rell the bottle warmer with fresh cold water. When

you switch on the bottle warmer, the progress indicator lls up

gradually to indicate that the appliance is warming again.

Problem The entire progress indicator ashes when warming baby food.

Cause

•

Due to variations in baby food consistency, it is not possible for

the appliance to detect precisely how long the baby food should

be warmed.

Solution

•

Stir the baby food while the jar or container is in the bottle warmer.

For optimal result, check its temperature while it is warming .

•

When the entire progress indicator lights up continuously, the

baby food is ready for feeding.

18 DEUTSCH

Inhalt

Wichtig! 19

Einführung 21

Allgemeine Beschreibung 22

Reinigen und Entkalken 31

Recycling 32

Garantie und Kundendienst 33

Fehlerbehebung 33

19DEUTSCH

Wichtig!

Lesen Sie diese Bedienungsanleitung vor dem Gebrauch des Geräts aufmerksam

durch, und bewahren Sie sie für eine spätere Verwendung auf.

Achtung!

- Tauchen Sie das Kabel, den Stecker oder das Gerät nicht

in Wasser oder andere Flüssigkeiten.

Achtung

- Verwenden Sie das Gerät nur im Haus.

- Lassen Sie das Netzkabel nicht über den Rand eines

Tisches oder einer Arbeitsäche hängen. Wickeln Sie das

überüssige Kabel am Sockel des Flaschenwärmers auf.

- Achten Sie darauf, dass das Netzkabel nicht in der Nähe

heißer Flächen verläuft.

- Schließen Sie das Gerät nur an eine geerdete Steckdose

an. Achten Sie stets darauf, dass der Stecker fest in der

Steckdose sitzt.

- Bevor Sie das Gerät an eine Steckdose anschließen,

überprüfen Sie, ob die auf dem Gerät angegebene

Spannung mit der Netzspannung vor Ort übereinstimmt.

- Wenn Sie ein Verlängerungskabel verwenden, muss

dieses geerdet und auf mindestens 13 A ausgelegt sein.

- Verwenden Sie das Gerät nicht, wenn der Netzstecker,

das Netzkabel oder das Gerät selbst defekt oder

beschädigt sind. Ist das Netzkabel defekt, darf es nur von

Philips, einem autorisierten Philips Service-Center oder

einer ähnlich qualizierten Person ausgetauscht werden,

um Gefährdungen zu vermeiden.

- Stellen Sie das Gerät nicht auf den heißen Gas- oder

Elektroherd oder in den beheizten Ofen.

- Dieses Gerät kann von Personen mit verringerten

physischen, sensorischen oder psychischen Fähigkeiten

oder Mangel an Erfahrung und Kenntnis verwendet

werden, wenn sie bei der Verwendung beaufsichtigt

20 DEUTSCH

wurden oder Anweisung zum sicheren Gebrauch des

Geräts erhalten und die Gefahren verstanden haben.

- Dieses Gerät kann von Kindern ab 8 Jahren verwendet

werden, wenn sie beaufsichtigt werden oder Anweisung

zum sicheren Gebrauch des Geräts erhalten und die

Gefahren verstanden haben. Die Reinigung und Wartung

darf nicht von Kindern durchgeführt werden, außer Sie

sind älter als 8 Jahre und beaufsichtigt. Bewahren Sie

das Gerät und das Kabel außerhalb der Reichweite von

Kindern unter 8 Jahren auf.

- Kinder dürfen nicht mit dem Gerät spielen.

- Achten Sie darauf, dass kein Wasser auf den Netzstecker

geschüttet wird.

- Verwenden Sie das Gerät nur wie in der

Bedienungsanleitung beschrieben, um mögliche

Verletzungen durch falsche Bedienung zu vermeiden.

- Wärmen Sie das Gerät nicht vor.

- Stellen Sie immer eine vollständig zusammengesetzte

Flasche mit Kappe in den Flaschenwärmer, bevor Sie

Wasser hinzufügen.

- Vergewissern Sie sich, dass Sie vor dem Einschalten des

Flaschenwärmers Wasser hinzufügen.

- Beachten Sie, dass heißes Wasser Verbrühungen

verursachen kann. Seien Sie vorsichtig, wenn der

Flaschenwärmer heißes Wasser enthält.

- Die Oberächen des Geräts können während des

Gebrauchs heiß werden und verfügen nach dem

Gebrauch über Restwärme.

- Bewegen Sie das Gerät nicht, wenn es heißes Wasser

enthält.

- Wenn die Nahrung oder die Milch die erforderliche

Temperatur erreicht haben, nehmen Sie die Flasche

oder den Behälter aus dem Flaschenwärmer. Wenn Sie

Nahrung oder Milch im Flaschenwärmer lassen, steigt die

Temperatur der Nahrung oder Milch an.

La page charge ...

Philips Avent SCF358 Manuel utilisateur

Ce manuel convient également à

Philips Avent SCF358 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents