TEAC P-05X Le manuel du propriétaire

P-05X

D01313221A

OWNER’S MANUAL .................... 3

MODE D’EMPLOI ...................... 31

MANUAL DEL USUARIO ........... 59

Super Audio CD/CD Transport

3

English

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

Model for USA

This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

China RoHS

o The information in the following table is only applicable to products for sale in the People’s Republic of China.

o The products sold in the European area are manufactured in accordance with the European RoHS Directive.

*%7

3;

*%7

4

IMPORTANT SAFETY INSTRUCTIONS (continued)

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to oper-

ate the equipment.

Laser information

This product contains a semiconductor laser system inside the cabi-

net and is classified as a “CLASS 1 LASER PRODUCT”.

To prevent being exposed to the laser beam, do not try to open the

enclosure.

Laser:

Type: SLD6163RL-G

Manufacturer: SONY CORPORATION

Laser output: Less than 1 mW on the objective lens

Wavelength: 785±15 nm (CD)

655±10 nm (Super Audio CD)

Model for USA

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class ! laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the manu-

facturer, or sold with the apparatus. When

a cart is used, use caution when moving

the cart/apparatus combination to avoid

injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

5

English

“DSD” is a registered trademark.

“Super Audio CD” is a registered trademark.

This product incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation.

The use of Rovi Corporation's copy protection technology in the product must be authorized by Rovi Corporation.

Reverse engineering and disassembly are prohibited.

MEXCEL is a registered trademark of Mitsubishi Cable Industries, Ltd. in Japan and other countries.

ESOTERIC is a trademark of TEAC CORPORATION, registered in the U.S. and other countries.

Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

V Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valu-

able resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

6

Contents

IMPORTANT SAFETY INSTRUCTIONS ...............................3

Before use .........................................................7

What’s in the box ...............................................7

Note about pinpoint feet .......................................7

Maintenance ...................................................7

Precautions for use ................................................8

Notes about discs .................................................8

Making connections ..............................................10

Names and functions of parts (main unit) .........................12

Names and functions of parts (display) ............................13

Names and functions of parts (remote control) ....................14

Notes about the remote control ..................................15

Basic operation ...................................................16

Turning the unit on and off ....................................16

Playback ..........................................................16

Pausing playback ..............................................17

Stopping playback ............................................17

Using the number buttons to select a track for playback .......18

Skipping tracks ................................................18

Searching backward/forward ..................................19

Repeat playback ..................................................19

REPEAT TRK ....................................................19

REPEAT DSC ...................................................19

Program playback ................................................20

Adding tracks to the end of the program ......................21

Clearing the entire program and resuming ordinary playback ..21

Changing the playback area ......................................21

Display ...........................................................22

Dimmer ..........................................................22

Thank you for purchasing this ESOTERIC product.

Read this manual carefully to get the best performance from this

product. After reading it, keep it in a safe place with the warranty card

for future reference.

Setting mode .....................................................23

Meanings of items shown in setting mode .....................24

Output connector/format setting ..............................24

Clock mode setting ............................................25

D/A converter setting .........................................25

Priority playback area setting ..................................25

Automatic display darkening setting ...........................25

Automatic power saving setting ...............................26

Restoring factory settings .........................................26

Troubleshooting ..................................................27

Specifications .....................................................29

Dimensional drawings ............................................30

7

English

What’s in the box

Check to be sure the box includes all the supplied accessories shown

below. Please contact the store where you purchased this unit if

any of these accessories are missing or have been damaged during

transportation.

Power cord × 1

HDMI cable × 1

Remote control (RC-1301) × 1

Batteries for remote control (AAA) × 2

Felt pads × 3

Owner’s manual (this document) × 1

Warranty card × 1

Note about pinpoint feet

High-precision metal pinpoint feet are attached firmly to the bottom

plate of this unit.

The stands for these feet are loose, but when the unit is placed in

position, it is supported by these pinpoint feet, which will effectively

disperse vibrations.

Chassis Pinpoint foot (metal)

Foot-stand (metal) Screws that attach

foot-stand

o Apply the included felt pads to the bottoms of the foot-stands to

avoid scratching the surface where the unit is placed.

Before use

Maintenance

Use a soft dry cloth to wipe the surface of the unit clean.

For stubborn smudges, use a damp cloth that has been thoroughly

wrung out to remove excess moisture.

V

For safety, disconnect the power plug from the

outlet before wiping the unit.

o Never spray liquid directly on this unit.

o Do not use chemically-treated wipes, thinner or similar substances

because they could damage the surface of the unit.

o Avoid allowing rubber or plastic materials to touch the unit for

long periods of time because they could damage the cabinet.

8

Precautions for use Notes about discs

The following marks appear on disc labels and disc cases. This unit

can play discs that have these marks without using an adapter.

This unit cannot play discs that do not have these marks.

Types of discs that can be played on this unit and

their marks

Super Audio CDs

Audio CDs

If you try to play any other type of disc with this unit, loud

noises that could damage speakers or harm hearing might

occur. Never try to play any type of disc other than those

shown above.

o This unit cannot play DVD video, DVD audio, video CD, DVD-ROM

and CD-ROM discs, for example.

o This unit might not be able to properly play Dual Discs, Copy

Control CDs or other special CDs that do not conform to the

Red Book CD standard. Operation and sound quality cannot be

guaranteed when special discs are used in this unit. If playback of

a special disc should cause trouble, contact the seller of the disc.

CD-R/CR-RW discs

This unit can play CD-R/CD-RW discs that are in audio CD format.

o Be sure to finalize discs created by CD recorders.

Depending on the quality of the disc and the condition of the

recording, playback might not be possible. For details, see the

operation manual for the device you are using.

o This unit is very heavy, so take care to avoid injury during installation.

o Do not install this unit in a location that could become hot. This

includes places that are exposed to direct sunlight or near a radia-

tor, heater, stove or other heating equipment. Moreover, do not

place it on top of an amplifier or other equipment that gener-

ates heat. Doing so could cause discoloration, deformation or

malfunction.

o Avoid locations that are extremely cold or exposed to vibrations,

excessive humidity or dust.

o In order to enable good heat dissipation, leave at least 20cm (8")

between this unit and walls and other equipment when installing

it. If you put it in a rack, take precautions to prevent overheating

by leaving at least 5cm (2") open above the top of the unit and

at least 10cm (4") open behind the unit. Failure to provide these

gaps could cause heat to build up inside and result in fire.

o If installing in a rack with a glass door, do not use the remote con-

trol tray OPEN/CLOSE (-) button to open the disc tray when the

door is closed. If the disc tray is forcibly prevented from moving,

damage could result.

o Place the unit in a stable location near the audio system that you

will use with it.

o Do not put anything on top of the unit.

o Do not lift or move the unit during playback because the disc

rotates at high speed. Doing so could damage the disc.

o Always remove any loaded disc before moving this unit or pack-

ing it for installation in a different location, for example. Moving

the unit with a disc inside could cause damage.

o Supply voltage to the power unit that matches the voltage indi-

cated on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

o Do not open the body of the unit because this could result in

damage to the circuitry or cause electric shock. If a foreign object

should enter the unit, contact your dealer.

o When removing the power plug from an outlet, always pull

directly on the plug. Never pull on the cord.

o The shape of the ES-LINK connector is the same as that of an

HDMI connector, but it transmits signals that are in a unique

ESOTERIC format. Do not connect the ES-LINK connector to an

HDMI connector on a device made by another company. ES-LINK

and HDMI connectors are not compatible.

9

English

Handling discs

o Load discs with their labeled sides up.

(CDs only have one playable side.)

o To remove a disc from its case, always press down on the center of

the case first and then hold the disc by its edges.

Removal from case Holding by edges

o Be careful when handling discs. If the side that contains the data

(unlabeled side) is scratched, smudged with fingerprints or other-

wise dirty or marred, errors could occur during playback.

o If the side of the disc that has the data encoded on it (unlabeled

side) becomes dirty with fingerprints or dust, use a soft cloth to

wipe the surface from the center directly toward the edge.

Always clean discs before storing them. Leaving a disc in an

unclean state might degrade its sound quality.

o Never use record cleaners, antistatic treatments, thinners or similar

chemicals to clean discs. Such chemicals could harm the surface

of the disc.

o Do not leave discs in places that are exposed to direct sunlight or

that are very humid or hot.

o When writing something on the label side of a disc, use a felt-tip

permanent marker. The use of a ballpoint pen or other pen with a

hard tip could damage the disc, making it unplayable.

o After you finish playing a disc, always put it back into its case for

storage. Failure to do so could result in warping or scratches.

o Do not apply labels or other materials to discs. Do not use a disc

that has sticky residue left on its surface after removing tape or a

sticker, for example. If such a disc is loaded, it might become stuck

in the unit or damage the unit.

o Never use commercially-available CD stabilizers. Doing so could

make the disc unplayable or damage the unit.

o Do not use cracked discs because they could damage the unit.

o Never use discs with irregular shapes, including heart-shaped and

octagonal discs, because they could damage the unit.

o Do not use printable discs, which allow printing on the label

side. Since the surface of such a disc has been specially treated, if

loaded, it might become stuck in the unit or damage the unit.

If you have any questions about how to handle a CD-R or

CD-RW disc, contact the manufacturer of the disc directly.

10

Making connections

A

C

B

D

B

Super Audio CD/CD transport (P-05X)

RCA coaxial digital cable

XLR digital cable

HDMI cable

XLR digital cable

BNC coaxial cable

Clock generator

(G-01X, G-02X, etc.)

CLOCK OUT

c

Wall socket

D/A converter (D-05X)

Digital audio input

connectors

D/A converter/amp

or other device

with digital input

Included power cord

If the clock generator has two or more

outputs, it can also be connected

directly to individual devices. Use the

connection method that provides the

preferable sound quality.

V

Precautions when making connections

o After completing all other connections, plug the power plug into a power outlet.

o Read the owner’s manuals of all devices that will be connected, and follow their instructions.

11

English

A SIGNAL GND grounding terminal

Connecting this grounding terminal to the grounding terminal

of the D/A converter, amplifier or other device might improve

the audio quality.

o This is not an electrical safety ground.

B Digital audio output (DIGITAL OUT) connectors

These output digital audio. Connect these to the digital input

connectors of a D/A converter (such as a D-05X).

ES-LINK: HDMI cable

o Use the two HDMI cables included (one each) with this unit

and an ESOTERIC D/A converter. The shape of the ES-LINK

connector is the same as that of an HDMI connector, but it

transmits signals that are in a unique ESOTERIC format. Do

not connect the ES-LINK connector to an HDMI connector on

a device made by another company. ES-LINK and HDMI con-

nectors are not compatible.

o The HDMI cable included with this unit is directional.

Connect the end of the cable with white marking to the D/A

converter.

Use commercially-available cables for the following

connections.

XLR: XLR digital cable

RCA: RCA coaxial digital cable

o Use one pair of these to connect the unit to the D/A converter.

Change the output settings of the connectors according to

the connectors being used (page24).

o We recommend using ES-LINK when connecting to a D-05X.

o When connecting to an ESOTERIC D/A converter (Grandioso

D1/D-01/D-02/D-03/D-05/D-02X/D-05X/D-07X) or D/A con-

verter that supports Dual AES, use two cables and connect

this unit’s XLR 1 (L) connector to the L connector on the D/A

converter and this unit’s XLR 2 (R) connector to the R connec-

tor on the D/A converter (Dual AES connection).

C Power inlet (~IN)

Connect the included AC power cord to this socket. After com-

pleting all other connections, plug the power plug into a power

outlet.

V

Use only a genuine ESOTERIC power cord. Use of

other power cords could result in fire or electric

shock.

V

Disconnect the power plug from the outlet if you

will not use the unit for a long time.

D CLOCK SYNC IN connector

Use this to input clock synchronization signals.

When using a master clock generator, connect its clock output

connector to this unit’s CLOCK SYNC IN connector.

Use a commercially-available BNC coaxial cable for this

connection.

Use a BNC coaxial cable with 50Ω or 75Ω impedance.

At ESOTERIC, we use ESOTERIC MEXCEL stressfree cables for

reference.

For detailed information, access the following website.

http://www.esoteric.jp/products/esoteric/accessory/indexe.html

12

Names and functions of parts (main unit)

A POWER button

Press to turn the unit on and off.

When the unit is on, the ring around the button lights blue.

When the unit is off, it is unlit.

When not using the unit, turn it off.

B CLOCK indicator

This shows the clock synchronization status.

When the clock sync setting is set to IN or MCK22M, this will

begin to blink. When a clock signal is detected and synchroniza-

tion occurs, it will stop blinking and stay lit.

C MENU button

Use to enter setting mode (page23).

D Remote control signal receiver

This receives signals from the remote control. When using the

remote control, point the end of it toward this receiver panel

(page15).

E Display

This shows playback time, track number and other information

(page22).

F Disc tray

Load a disc for playback here (page16).

G Tray open/close (-) button

Press to open and close the disc tray (page16).

H Stop (8) button

Press to stop playback (page17).

When stopped, press and hold for at least two seconds to

change the playback area of a Super Audio CD (page21).

Press when in setting mode to complete changing settings and

show the ordinary display (page23).

I Play (7) button

Press to start disc playback (page16).

During playback, the indicator next to this button lights.

J Pause (9) button

Press to pause playback (page17).

When paused, the indicator next to the play button blinks.

K Skip (.//) buttons

Use to skip to the previous or next track (page18).

Press and hold for at least one second during playback to search

backward/forward. Repeatedly press and hold for more than one

second to change the backward/forward search speed to one of

three levels (page19).

Use to change parameters when in setting mode (page23).

A C D F

H I J K

E

B

G

13

English

Names and functions of parts (display)

a Disc type

This shows the type of disc that is currently loaded.

SACD: Super Audio CD

CD: Audio CD

b Information

During Super Audio CD playback

No indicator:

The two-channel area of a Super Audio CD is selected.

MULTI D-MIX:

This appears when the multichannel audio of a Super Audio

CD is being downmixed and output.

c Repeat indicator

This appears during repeat playback (page19).

d Clock mode

This shows the clock mode (page25).

No indicator: CLK set to OFF

CLK: CLK set to IN

MCK: CLK set to MCK22M

e Input clock frequency

The synchronization signal (clock) frequency input through the

CLOCK SYNC IN connector is shown.

f Message display area

The playback time and various messages appear here.

SACD

0

:

29

r

T

1

MULTID-MIX CLK44.1kHz

1

a b c d e

f

14

Names and functions of parts (remote control)

When both the main unit and the remote control have buttons with

the same functions, the instructions in this manual refer to only the

main unit buttons, but the remote buttons can be used in the same

way.

a STANDBY/ON button

This button is not used with this unit.

b Number buttons

Use to select tracks.

c REPEAT button

Use for repeat playback (page19).

Press and hold to enter program mode (page20).

d PLAY AREA button

When stopped, press to change the playback area of a Super

Audio CD (page21).

e INPUT buttons (k/j)

These buttons are not used with this unit. They can be used to

switch the inputs of ESOTERIC D/A converters (including the

D-05X) and amplifiers.

f SETUP button

This button is not used with this unit. It can be used with

ESOTERIC D/A converters (including the D-05X), amplifiers and

other products.

g DIMMER button

Use to adjust the brightness of the main unit’s display (page22).

h Tray OPEN/CLOSE (-) button

Press to open and close the disc tray (page16).

i DISPLAY button

During playback, press this button to change what is shown on

the display (page22).

j Skip (.//) buttons

Press to skip to the previous or next track.

Press and hold for at least one second during playback to search

backward/forward. Repeatedly press and hold for more than one

second to change the backward/forward search speed to one of

three levels (page19).

Use to change parameters when in setting mode (page23).

a

c

f

d

h

i

j

l

m

n

k

g

b

e

15

English

k Stop (8) button

Press to stop playback (page17).

l Play/pause (y/9) button

Press when stopped or paused to start playback.

Press during playback to pause (page17).

m VOLUME buttons (+/−)

These buttons are not used with this unit. They can be used with

ESOTERIC D/A converters (including the D-05X), amplifiers and

other products.

n MUTE button

This button is not used with this unit. It can be used to mute

ESOTERIC D/A converters (including the D-05X) and amplifiers.

Notes about the remote control

Precautions when using the remote control

o When using the remote control, point it toward the remote con-

trol signal receiver on the main unit from a distance of 7m (23ft)

or less. Do not place obstructions between the main unit and the

remote control.

o The remote control might not work if the remote control signal

receiver is exposed to direct sunlight or bright light.

o Beware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by

infrared rays.

Installing batteries

Remove the cover from the back of the remote control and insert

two AAA batteries with their ¥/^ oriented as shown in the case.

Replace the cover.

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

V

CAUTION

Misuse of batteries could cause them to rupture or leak, which

might result in fire, injury or the staining of nearby materials.

Please read and observe the precautions on page5 carefully.

16

Basic operation

Playback

1 Press the tray open/close (-) button.

The disc tray opens forward.

2 Place a disc centered on the tray with the labeled

side up.

o If the tray is closed while a disc is outside the center guides,

the disc might become stuck inside and the tray might not

open. Be sure to always place discs within the guides at the

center of the tray.

Turning the unit on and off

Press the POWER button to turn the unit on when off or off when on.

When on, the power indicator and the display light.

o When using this unit, turn on the D/A converter, amplifier and other

devices that are connected to it. When doing this, turn the amplifier

on last.

17

English

3 Press the tray open/close (-) button.

The disc tray is drawn into the unit. Be careful not to let your fin-

gers be pinched when the tray closes.

o The unit takes some time to load the disc.

4 Press the play (t) button.

Playback starts.

Pausing playback

During playback, press the pause (9) button to pause playback.

When paused, the indicator next to the main unit play (t) button

blinks blue.

Press the play (t) or pause (9) button to restart playback.

Stopping playback

Press the stop (8) button to stop playback.

18

Using the number buttons to select a

track for playback

When playing or stopped, you can press number buttons to select a

track and start playing it back.

To play a track with a single-digit number, press that number button.

To play a double-digit track number, press the +10 button as many

times as necessary, and then press the corresponding number button

for the second digit. After the track number is input, playback starts.

Examples:

Track 7:

Track 23:

Playback (continued)

Skipping tracks

During playback, press a skip button (.//) on the main unit

or the remote control to skip to the previous or next track and start

playback.

o Press the . button once to return to the beginning of the cur-

rent track. Press the . button repeatedly to return to an earlier

track.

If the playback position is less than one second from the begin-

ning of the current track, however, pressing the . button will

skip to the beginning of the previous track.

o When stopped or paused, use the .// buttons to select a

track and pause at its beginning.

19

English

Repeat playback

The repeat mode changes each time you press the REPEAT button

during playback.

REPEAT TRK REPEAT DSC

(track repeat) (disc repeat)

REPEAT OFF

(ordinary playback)

REPEAT TRK

The current track is played back repeatedly. During repeat playback,

select a different track to repeat playback of that track.

REPEAT DSC

All tracks on the current disc are played back repeatedly.

o During repeat playback, the repeat mode is shown.

o Stopping playback ends repeat playback mode.

Searching backward/forward

Press for at least

1second.

During playback, press and hold a skip (.//) button on the

main unit or the remote control (for more than one second) until

searching backward/forward starts. When you find the point where

you want to listen, press the play (y) button on the main unit or the

play/pause (y/9) button on the remote control.

You can change the backward/forward search speed by pressing the

skip (.//) button for at least one second and then releasing it.

The speed that the < or > blinks on the display also changes.

Low speed Medium speed High speed

Playback at normal speed

o Continuously holding the button down will not change the speed.

20

You can program up to 30 tracks in the order that you want to listen

to them.

1 When stopped or during playback, press the

REPEAT button for at least two seconds.

If you press this button during playback, the currently playing

track will be added to the program as the first track.

Press for at least

2seconds.

2 Use number buttons to select tracks you want

to program.

Examples:

Track 3:

Track 12:

Track 20:

Program playback

CD

2PGM

1

Programmed track number Program number

To program multiple tracks, continue pressing the number buttons.

o Track numbers that do not exist on the currently loaded disc

cannot be added to the program.

3 When you are done adding tracks to the pro-

gram, press the play/pause (y/9) button.

Program playback starts.

o If you created the program during playback, you do not need

to press the play/pause (y/9) button.

La page charge ...

TEAC P-05X Le manuel du propriétaire

Ce manuel convient également à

TEAC P-05X Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents