Esoteric C-03Xs Le manuel du propriétaire

C-02X/C-03Xs

Linestage Preamplifier

OWNER’S MANUAL .................... 3

MODE D’EMPLOI ...................... 23

MANUAL DEL USUARIO ........... 43

D01253321B

3

English

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

Model for USA

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause unde-

sired operation.

This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

DECLARATION OF CONFORMITY

We, TEAC AUDIO EUROPE, Liegnitzer Straße 6, 82194

Gröbenzell, Germany declare in own responsibility,

the TEAC product described in this manual is in com-

pliance with the corresponding technical standards.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to oper-

ate the equipment.

China RoHS

o The information in the following table is only applicable to products for sale in the People’s Republic of China.

o The products sold in the European area are manufactured in accordance with the European RoHS Directive.

*%7

&;&;V

*%7

4

IMPORTANT SAFETY INSTRUCTIONS (continued)

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the manu-

facturer, or sold with the apparatus. When

a cart is used, use caution when moving

the cart/apparatus combination to avoid

injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

5

English

MEXCEL is a registered trademark of Mitsubishi Cable Industries, Ltd. in Japan and other countries.

ESOTERIC is a trademark of TEAC CORPORATION, registered in the U.S. and other countries.

Other company names and product names in this document are the trademarks or registered trademarks of their respective owners.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valu-

able resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

V Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

6

Contents

Thank you for purchasing this Esoteric product.

Read this manual carefully to get the best performance from this

product. After reading it, keep it in a safe place with the warranty card

for future reference.

IMPORTANT SAFETY INSTRUCTIONS ...............................3

Before use .........................................................6

Precautions for use ................................................7

Maintenance ......................................................7

Connections ....................................................... 8

Names and functions of parts (main unit) .........................10

Remote control ...................................................11

Names and functions of parts (remote control) ....................12

Basic operation ...................................................13

Balance and input level settings ..................................15

Additional settings ...............................................17

Troubleshooting ..................................................21

Specifications and dimensional drawings .........................22

Before use

What's in the box

Check to be sure the box includes all the supplied accessories shown

below. Please contact the store where you purchased this product if

any of these accessories are missing or have been damaged during

transportation.

Power cord × 1

Remote control × 1

C-02X: RC-1315

C-03Xs: RC-1301

Batteries for remote control (AAA) × 2

Felt pads* × 4

Owner’s manual (this document) × 1

Warranty card × 1

* Apply the included felt pads to the bottoms of the foot-stands

(C-02X) or feet (C-03Xs) to avoid scratching the surface where the

unit is placed.

Note about pinpoint feet (C-02X only)

High-precision metal pinpoint feet are attached firmly to the bottom

plate of the C-02X.

The stands for these feet are loose, but when the unit is placed in

position, it is supported by these pinpoint feet, which will effectively

disperse vibrations.

Chassis Pinpoint foot (metal)

Foot-stand (metal)

Screws that attach

foot-stand

o This unit is very heavy, so take care to avoid injury during installation.

o Apply the included felt pads to the bottoms of the foot-stands to

avoid scratching the surface where the unit is placed.

7

English

Precautions for use

o Place the unit in a stable location near the stereo system that you

will use with it.

o Do not install this unit in a location that could become hot. This

includes places that are exposed to direct sunlight or near a radia-

tor, heater, stove or other heating equipment. Moreover, do not

place it on top of another amplifier or equipment that generates

heat.

o Avoid locations that are subject to vibrations or exposed to exces-

sive dust, cold or moisture.

o In order to enable good heat dissipation, leave at least 20 cm (8")

between this unit and walls and other equipment when installing it.

If you put it in a rack, take precautions to prevent overheating by

leaving at least 5 cm (2") open above the top of the unit and at

least 10 cm (4") open behind it.

o Do not install the unit face up or on its side.

o Do not place anything, not even CDs, CD-Rs, LP records or cassette

tapes, on top of the unit. Do not put cloth on top of the unit or

place the unit on top of bedding or thick carpet.

o Do not move the unit during use.

o Be careful to avoid injury when moving the unit due to its weight.

Have someone help you move it if necessary.

o The voltage supplied to the unit should match the voltage printed

on the rear panel. If you are in any doubt regarding this matter,

consult an electrician.

o Do not open the body of the unit as this might result in damage

to the circuitry or cause electric shock. If a foreign object should

get into the unit, contact your dealer.

o When removing the power plug from the wall outlet, always pull

directly on the plug; never yank on the cord.

Maintenance

Use a soft dry cloth to wipe the surface of the unit clean.

For stubborn smudges, use a damp cloth that has been thoroughly

wrung out to remove excess moisture.

V

For safety, disconnect the power cord from the out-

let before cleaning.

o Never spray liquid directly on this unit.

o Do not use thinner or alcohol as they could damage the surface

of the unit.

o Avoid allowing rubber or plastic materials to touch this product

for long periods of time, because they could damage the cabinet.

8

A

D

B

C

XLR pin assignment

1. COMMON

2. HOT (+)

3. COLD (−)

XLR cables

RCA audio cables

XLR cables

AUDIO OUT

Super Audio CD player,

tuner, etc.

Super Audio CD player,

etc.

Connections

V

Precautions when making connections

o After completing all other connections, plug the power plug into a power outlet.

o Read the owner’s manuals of all devices that will be connected, and follow their instructions.

o Do not bundle connecting cables with power cords. Doing so could cause noise.

Included power cord

Power amplifier, etc.

AUDIO IN

Connect using a set

of only one type.

c

Wall outlet

9

English

A Analog input connectors (LINE IN)

Connect the analog output connectors of Super Audio CD play-

ers, DVD players, cassette decks, tuners and other equipment to

these connectors.

Connect the R connector of a pair on this unit to the right (R)

connector of an output device and the L connector of the same

pair on this unit to the left (L) connector of the output device.

Use commercially-available cables for connections.

For XLR connectors: Use a balanced XLR audio cable.

Insert a balanced XLR plug until the con-

nector lever locks. Press this lever when

disconnecting.

For RCA connectors: Use an RCA audio cable.

Connect the white pin plugs to the white

(L) connectors and connect the red pin

plugs to the red (R) connectors.

o The XLR input connectors can be switched to 3 HOT (+)

(page 16).

o This unit does not have a built-in phono equalizer, so record

players cannot be connected to it directly.

To use a record player with this unit, connect it through a

phono equalizer, for example.

B Grounding connector (SIGNAL GND)

Using a commercially-available sheathed wire to connect this

to the grounding terminal of a Super Audio CD player, power

amplifier or other device might improve the audio quality.

o This is NOT an electrical safety ground.

C Analog output connectors (LINE OUT)

Output two channels of analog audio signals.

Connect these to the analog input connectors of a power ampli-

fier, for example.

Connect the R connector of a pair on this unit to the right (R)

connector of an input device and the L connector of the same

pair on this unit to the left (L) connector of the input device.

Use commercially-available cables for connections.

For XLR connectors: Use a balanced XLR audio cable.

Insert a balanced XLR plug into the con-

nector until it locks.

For RCA connectors: Use an RCA audio cable.

Connect the white pin plugs to the white

(L) connectors and connect the red pin

plugs to the red (R) connectors.

D AC power inlet

Connect the included power cord to this inlet. After completing

all other connections, plug the power plug into a power outlet.

o Unplug the power cord from the outlet when you are not

planning to use the unit for an extended period of time.

V

Use only a genuine Esoteric power cord. Use of

other power cords could result in fire or electric

shock.

At Esoteric, we use Esoteric MEXCEL stressfree cables for

reference.

For detailed information, access the following website.

http://www.esoteric.jp/products/esoteric/accessory/indexe.html

10

Names and functions of parts (main unit)

A INPUT knob

Turn this knob to select the active input. Select the input that is

connected to the device you want to use.

o You can change the names that are shown on the display for

the connectors, as well as set the unit to skip them (page 20).

B POWER button

Press this button to turn the unit on or off.

The blue indicator lights when the unit is turned on.

o Turn the unit off when not using it.

o To protect your speakers, follow the proper procedures when

you turn the unit on or off (pages 13 and 14).

C Display

Shows the current input source name, volume, setting items, etc.

D Output indicators

These indicators light to show the output status of the selected

source.

XLR

Lights when a signal is output from the XLR connectors

RCA

Lights when a signal is output from the RCA connectors

POLARITY

Lights when output polarity Invert is ON

BALANCE

Lights when left-right balance is set to anything but center

E Remote control signal receiver

Signals sent from remote controls are received here. When using

a remote, point it toward this spot (page 11).

F VOLUME knob

Use to adjust the volume.

Turn this knob clockwise to increase the volume and counter-

clockwise to decrease it.

o If through output (RCA2) is set to THRU and the input source

is RCA 2, the VOLUME knob will not function (page 19).

V

Sudden loud noises might cause hearing damage

and other trouble.

Always minimize the volume before starting

playback, and adjust it to an appropriate level

after playback begins.

A

B C

F

ED

C-02X

C-03Xs

A

B C

F

ED

11

English

Remote control

Precautions when using the remote

control

When using the remote control, point it toward the remote control

signal receiver on the main unit from a distance of 7 m (23 ft) or less.

Do not place obstructions between the main unit and the remote

control.

Moreover, operation from an angle can make reception difficult, so

use the remote facing the front of the main unit as much as possible.

7 m/23 ft

Remote control signal receiver

o The remote control might not work if the remote control signal

receiver is exposed to direct sunlight or bright light.

o Beware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by

infrared rays.

Installing batteries

Remove the cover from the back of the remote control and insert

two AAA batteries with their ¥/^ oriented as shown in the case.

Replace the cover.

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

Precautions concerning batteries

V

Misuse of batteries could cause them to rupture

or leak, which might result in fire, injury or the

staining of nearby materials.

Please read and observe the precautions on

page 5 carefully.

12

Names and functions of parts (remote control)

o The buttons not explained here do not function with this unit.

o This remote control can also be used for other Esoteric Super

Audio CD/CD players and D/A converters.

o Some models will not pause when you press the playback/pause

button (7/9) button.

a STANDBY/ON (setting) button

Use to confirm selection of some of the settings explained in

“Additional settings” (pages 17-21). You can also assign a

name to a connector using this button (page 20).

o You cannot turn the unit on or off using this button.

b INPUT (k/j) buttons

Press these buttons to switch between input sources. Select the

connector that is connected to the device you want to play.

Use to select settings for “Balance and input level settings”

(pages 15-16) and “Additional settings” (pages 17-21).

Use as cursor keys when entering an input source name.

c SETUP button

Use with “Balance and input level settings” and “Additional set-

tings” (pages 15 and 17).

d DIMMER button

Use to adjust the brightness of the display and indicators (page

14).

e VOLUME (+/−) buttons

Use to adjust the volume. Press the + button to increase the vol-

ume and the − button to decrease it.

o If you set the RCA 2 input connectors to “THRU”, the VOLUME

buttons will not work when the input is set to RCA2 (page

19).

f MUTE button

Press this button to temporarily mute the sound.

Press again to restore the volume setting (page 14).

o When muted, “MUTE” and the ordinary display are shown

alternately.

If both the main unit and the remote control have buttons with

the same function, we only explain procedures using one of them

in this manual. However, the other can also be used in the same

manner.

a

c

e

f

d

b

This illustration shows the C-02X remote control. The C-03Xs remote

control has the same types of buttons in the same positions.

13

English

Basic operation

4 Play the source, and then adjust the volume by turn-

ing the VOLUME knob.

V

Sudden loud noises might cause hearing damage

and other trouble.

Always minimize the volume before starting

playback, and adjust it to an appropriate level

after playback begins.

1 Turn on the connected input source devices.

2 Press the POWER button to turn the unit on.

The indicator lights blue.

o Turn on the power amplifier after turning on this unit.

3 Turn the INPUT knob to select an input source.

14

Basic operation (continued)

Turning the unit off

There might be noise from the speakers if the unit is turned off sud-

denly. When you turn the unit off, follow the steps below.

1 If a connected device is playing back, stop playback.

o Turn off the power amplifier first.

2 Turn the unit's VOLUME knob counterclockwise to

minimize the volume.

o Always turn the volume to the minimum level before you

turn the unit on or off. Failure to do so could cause sudden

loud noises that might result in harm to your hearing or dam-

age to the speakers when you turn the unit on.

3 Press the POWER button to turn the unit o.

4 Turn o the connected input source devices.

Using the dimmer

Each time you press the DIMMER button, the brightness of the dis-

play and indicators change as follows.

3 (Standard brightness)

2

1

0 (Unlit)

o Even when set to 0 (unlit), the display will light at standard bright-

ness for a few seconds when you press a button or turn a knob.

o In setting mode, the display lights at standard brightness.

Muting the output

Press the remote control MUTE button to temporarily mute the

sound. Press again to restore the previous volume setting.

o While the sound is muted, “MUTE” and the selected input connec-

tor name appear alternately on the display.

o You can also restore the sound by turning the VOLUME knob or by

pressing the VOLUME buttons (+/−).

15

English

You can set the left and right balance, output level adjustment and

phase inversion. You can set these independently for each pair of

input connectors.

1 Turn the INPUT knob to select the input source you

want to set.

2 Press the SETUP button repeatedly to select the set-

ting item you want to change.

Each time you press the SETUP button, the display changes.

o While making these settings, the SETUP indicator appears at

the top left of the display.

o To exit setting mode and return to the ordinary display, do

nothing for at least 10 seconds.

3 Press the INPUT (k/j) buttons to change the setting.

4 Press the SETUP button repeatedly until the display

resumes showing its usual contents. Setting mode

ends when the usual contents are shown.

Setting mode will also end and the ordinary display will reappear

if nothing is done for 10 or more seconds.

o These settings will be retained even if the power cord is

disconnected.

Balance and input level settings

16

Left and right balance setting

(Bal>***)

Adjust the balance between the left and right output channels.

You can set this to values between L 6.0 dB and R 6.0 dB in 0.5dB

increments. You can also set this so that just one channel is muted.

The default value is 0.0 dB (no balance adjustment).

Muting just one channel

Press the k button to select “Bal>R only” to output only the right

channel.

Likewise, press the j button to select “Bal>L only” to output only

the left channel.

o When the balance has been adjusted, the BALANCE indicator

lights to show this.

Adjusting the output level

(Level>***)

You can adjust the output level for the selected input.

You can set this to values between –18.0 dB and +18.0 dB in 0.5dB

increments.

The default value is 0.0 dB.

o If the total of the output level and volume settings exceed 0 dB,

the output level indication will blink.

Lower the output level or volume until it stops blinking.

Note about these settings and sound quality

The left-right balance and output level settings are related to the

volume. This unit’s microcomputer analyzes these settings and

the volume level value comprehensively to conduct unified con-

trol of volume amplification.

For this reason, unlike ordinary amplifiers that pass audio signals

through multiple circuits, these settings will not degrade the

audio quality.

Phase inversion

(Invert>***)

This can be used to reverse the phase of the audio signal output.

For example, if the XLR output of a device that sends a signal to this

unit’s input is 2 HOT, but the XLR input of the device that receives the

signal output from this device is 3 HOT, set this to ON.

By default, this is set to OFF.

OFF

No phase inversion

ON

Phase inversion enabled

o When the polarity has been inverted, the POLARITY indicator

lights to show this.

Balance and input level settings (continued)

17

English

Additional settings

You can also make the following settings and restore factory defaults.

Volume curve

Output

Through (RCA2)

Illumination

Input source name

Automatic display (FL) off

Automatic power saving function

1 Press and hold the SETUP button for at least 2seconds.

Press for at least

2 seconds

“VolMode>***” appears on the display and the unit enters set-

ting mode.

2 Press the SETUP button repeatedly to select the set-

ting item you want to change.

Each time you press the SETUP button, the display changes.

o To exit setting mode and return to the ordinary display, do

nothing for at least 10 seconds.

3 Press the INPUT (k/j) buttons to change the setting.

4 Press the SETUP button repeatedly until the display

resumes showing its usual contents. Setting mode

ends when the usual contents are shown.

Setting mode will also end and the ordinary display will reappear

if nothing is done for 10 or more seconds.

o These settings will be retained even if the power cord is

disconnected.

18

Output setting

(Out>***)

You can set which connectors output audio.

The default setting is “BOTH”.

XLR

Sound is output from the XLR 1/XLR 2 connectors.

RCA

Sound is output from the RCA 1/RCA 2 connectors.

BOTH

Sound is output from both the XLR 1/XLR 2 connectors and RCA

1/RCA 2 connectors.

o The setting is shown by the output indicator.

When BOTH is selected, the XLR and RCA indicators will both light.

Volume curve setting

(VolMode>***)

With this unit, the volume level can be adjusted by dB or with a “vol-

ume curve” of 100 steps numbered 0 to 99 between −∞ to 0 dB.

When dB is selected, the volume can be adjusted from −99.5 dB to 0

dB in 0.5dB steps.

You can select from the 5 different volume curves (A, B, C, D and E)

shown below.

The default value is “dB”.

0

-50

-40

-30

-20

-10

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 99

-90

-80

-70

-60

A

B

C

D

E

Steps

Volume [dB]

o When you change the volume curve setting, the volume will be

minimized.

o When dB is selected the volume is shown in dB. When a volume

curve is selected (A–E), steps 0–99 are shown.

Additional settings (continued)

19

English

Through (RCA2)

(RCA2>***)

You can select whether to use the RCA 2 connectors as normal input

connectors or as signal through connectors.

The default setting is “NML”.

NML (normal)

Select this to use the RCA 2 connectors as normal input connectors.

THRU (through)

The volume level adjusted using the VOLUME knob is ignored

when this setting is selected. Sound signals passing through the

RCA 2 connectors are output as they are. (No gain adjustment is

made by the preamplifier.)

After selecting “THRU”, press the STANDBY/ON (setting) button to

activate the setting.

“THRU” appears on the display instead of the volume level set by

using the VOLUME knob.

For example, if you connect the pre-out connectors (FRONT L/R)

of an AV amplifier to this unit’s RCA 2 connectors, and set RCA2 to

“THRU”, you can also use the speakers connected through this unit

as the front speakers of the AV amplifier. (The AV amplifier controls

volume adjustment when the input source is set to “RCA2”.)

o If through output (RCA2) is set to THRU and the input source is

RCA 2, the VOLUME knob will not function.

V

Since this unit’s VOLUME knob will not function when set

to “THRU”, be careful if you connect a device that does

not have a volume control to the RCA 2 input connectors.

When you change the input source to RCA2, very loud

sounds could be output suddenly, resulting in harm to

your hearing and damage to the speakers.

When connecting a device that does not have a volume

control to the RCA 2 input connectors and setting RCA2

to “THRU”, always connect a device that has a volume

control to this unit’s analog output connectors (LINE

OUT). Use that device to minimize the volume before

switching the input source to RCA2, and then gradually

raise the volume level.

Illumination

(Light>***)

You can set whether or not the rings of the knobs light.

The default setting is “AUTO”.

AUTO

When the knobs are operated, their rings light.

ON

The rings around the knobs will stay lit.

OFF

The rings around the knobs do not light.

20

Input source name

XLR1=

XLR2=

RCA1=

RCA2=

RCA3=

You can change the names shown on the display for the unit’s con-

nectors when you change the input source. You can set the names as

you like (up to five characters).

You can also set the unit to skip connectors that do not have con-

nected devices when you change the input source.

For example, when a Super Audio CD player is connected to the RCA

2 connectors and a DVD player is connected to the RCA 3 connec-

tors, the RCA 2 and RCA 3 connectors can be set to “SACD” and “DVD”

respectively while the other connectors can be set to “*skip”. When

you change the input source, only “SACD” and “DVD” will be selected,

making it easier to select only the connectors you want to use.

Use the INPUT (k/j) buttons to select the connector name.

Connector name options: CD, DAC, SACD, DVD, CD-R,

DVD-R, TAPE, MD, TUNER, PC, MP3, AUX, TV, VIDEO, VCR,

*skip, (editable)

o The skip function will not work when all connectors are set to

“*skip”.

Creating your own input connector name

1. When the input connector name (XLR1, XLR2,

XLR3, RCA1 or RCA2) and “=” are shown, press the

INPUT (k/j) buttons repeatedly until the editable

screen appears (default setting: “88888”).

2. Press the STANDBY/ON (setting) button.

3. Enter the characters.

Press the INPUT (k/j) buttons to move the cursor.

Press the VOLUME (+/–) buttons to select characters.

4. When you have finished entering the characters,

press the STANDBY/ON (setting) button to confirm

the selection.

o While entering the name, the volume and input connec-

tor cannot be changed.

o Available characters

English letters: A–Z, a–z

Numbers: 0–9

Symbols: ! " # $ % & ' ( ) * + , − . / : ; < = > ? @ 8 (blank)

Automatic display backlight (FL) off

(FLaOFF>***)

You can set the display backlight to automatically turn off if no opera-

tion is conducted for a certain amount of time. The default setting is

“30m”.

15m

If no operation is conducted for 15 minutes, the display automati-

cally turns off.

30m

If no operation is conducted for 30 minutes, the display automati-

cally turns off.

60m

If no operation is conducted for 60 minutes, the display automati-

cally turns off.

OFF

The display never turns off automatically.

o If the display backlight (FL) is left ON with the same indication for

a long time, brightness irregularities might occur. For this reason,

we recommend that you enable the automatic display backlight

off function.

Additional settings (continued)

La page charge ...

Esoteric C-03Xs Le manuel du propriétaire

Ce manuel convient également à

Esoteric C-03Xs Le manuel du propriétaire

dans d''autres langues

Documents connexes