Esoteric Grandioso P1X Le manuel du propriétaire

D0134 7821E

OWNER’S MANUAL .................... 3

MODE D’EMPLOI ...................... 33

MANUAL DEL USUARIO ........... 63

3

English

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the AC

outlet with its POWER or STANDBY/ON switch not in the ON position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

IN USA/CANADA, USE ONLY ON 120V SUPPLY.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an

incorrect type of battery. Replace only with the same or equiva-

lent type.

4

IMPORTANT SAFETY INSTRUCTIONS (continued)

V

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

o Do not expose batteries to extremely low air pressure as it could

result in an explosion or leakage of flammable liquids or gases.

Laser information

This product contains a semiconductor laser system inside the cabi-

net and is classified as a “CLASS 1 LASER PRODUCT”.

To prevent being exposed to the laser beam, do not try to open the

enclosure.

Laser:

Type: RLD2WMFR1

Manufacturer: ROHM Co.,Ltd.

Laser output: Less than 0.7mW on the objective lens

Wavelength: 790 ±15nm (CD)

650 ±10nm (Super Audio CD)

Model for USA

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class ! laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

5

English

Supplier’s Declaration of Conformity

Model number: GrandiosoP1X

Trade name: ESOTERIC

Responsible party:

Pioneer & Onkyo U.S.A. Corporation

Address: 22828 Lockness Avenue, Torrance, CA90501 U.S.A.

Telephone number: 1-201-785-2600

This device complies with Part.15 of FCC Rules.

Operation is subject to the following two conditions:

1) This device may not cause harmful interference

2) This device must accept any interference received, including

interference that may cause undesired operation.

Information

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

“DSD” is a registered trademark.

“Super Audio CD” is a registered trademark.

This product incorporates copy protection technology that is protected

by U.S. patents and other intellectual property rights of Rovi Corporation.

The use of Rovi Corporation’s copy protection technology in the product

must be authorized by Rovi Corporation.

Reverse engineering and disassembly are prohibited.

ESOTERIC is a trademark of TEAC CORPORATION, registered in the U.S.

and other countries.

Other company names, product names and logos in this document

are the trademarks or registered trademarks of their respective owners.

Information about copyrights and licenses related to open source

software is included at the end of this document.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valu-

able resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC, 2013/56/EU), then the chemical symbols

for those elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

6

Contents

IMPORTANT SAFETY INSTRUCTIONS ...............................3

Before use .........................................................7

Included accessories ...........................................7

Note about pinpoint feet .......................................7

Maintenance ...................................................7

Precautions for use ................................................8

Notes about discs .................................................8

Connections (main unit) ..........................................10

Connections (power supply unit) .................................12

Main unit parts and functions .....................................14

Power supply unit/display parts and functions ....................15

Power supply unit .............................................15

Display ........................................................15

Notes about the remote control ..................................16

Remote control parts and functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Basic operation ...................................................18

Turning the GrandiosoP1X on and off .........................18

Playback ..........................................................18

Pausing playback ..............................................19

Stopping playback ............................................19

Changing the playback area ...................................20

Switching to ES-LINK mode ....................................20

Searching backward/forward ..................................20

Skipping tracks ................................................21

Using the number buttons to select a track for playback .......21

Repeat playback ..................................................21

Playback modes ..................................................22

Changing playback modes ....................................22

Program playback .............................................22

Shuffle playback ...............................................22

Display ...........................................................23

Dimmer ..........................................................23

Setting mode .....................................................24

Setting items and their options ...................................25

Meanings of items shown in setting mode .....................25

Output connector/format setting ..............................25

ES-LINK setting ................................................26

Clock setting ..................................................26

D/A converter setting .........................................26

Automatic display darkening setting ...........................27

Priority playback area setting ..................................27

Automatic power saving setting ...............................27

Showing firmware versions ....................................27

Restoring factory settings .........................................28

Troubleshooting ..................................................28

Specifications .....................................................30

Dimensional drawings ............................................31

Main unit ......................................................31

Foot placement diagram ......................................31

Power supply unit .............................................32

Foot placement diagram ......................................32

ATTENTION

The main unit only outputs digital signals from the one

selected type of connector.

For information about settings, see “Setting mode” on

page 24 and “Output connector/format setting” on

page25.

Thank you for purchasing this ESOTERIC product.

Read this manual carefully to get the best performance from this

product. After reading it, keep it in a safe place with the warranty card

for future reference.

7

English

Included accessories

Check to be sure the box includes all the supplied accessories shown

below. Please contact the store where you purchased this product if

any of these accessories are missing or have been damaged during

transportation.

Power cord × 1

DC power cords × 2

HDMI cable × 1

Remote control (RC-1333) × 1

Batteries for remote control (AA) × 2

Felt pads × 8

Owner’s manual (this document) × 1

Warranty card × 1

Before use

Note about pinpoint feet

High-precision metal pinpoint feet are attached securely to the bot-

tom plates of the main and power supply units.

Chassis Pinpoint foot (metal)

Foot-stand (metal) Screws that attach

foot-stand

The stands for these pinpoint feet are loose, but the stands support

the units when they are placed, effectively dispersing vibrations.

o Apply the included felt pads to the bottoms of the foot-stands to

avoid scratching the surface where the units are placed.

Maintenance

Use a soft dry cloth to wipe the surfaces of the units clean.

For stubborn smudges, use a damp cloth that has been thoroughly

wrung out to remove excess moisture.

o Never spray liquid directly on these units.

o Do not wipe with chemical cleaning cloths, thinner or other

chemical agents. Doing so could damage the surfaces of the units.

o Avoid allowing rubber or plastic materials to touch the units for

long periods of time, because they could damage the cabinets.

V

For safety, disconnect the power plug from the

outlet before cleaning.

8

Precautions for use

o These units are very heavy, so take care to avoid injury during

installation.

o Do not install these units in locations that could become hot. This

includes places that are exposed to direct sunlight or near a radia-

tor, heater, stove or other heating equipment. Moreover, do not

place them on top of an amplifier or other equipment that gener-

ates heat. Doing so could cause discoloration or deformation.

o Avoid locations that are extremely cold or exposed to vibrations,

excessive humidity or dust.

o In order to enable good heat dissipation, leave at least 20cm (8")

between these units and walls and other equipment when install-

ing them. If you put them in a rack, take precautions to prevent

overheating by leaving at least 5cm (2" ) open above the tops

of the units and at least 10cm (4") open behind them. Failure to

provide these gaps could cause heat to build up inside and result

in fire.

o If installing in a rack with a glass door, do not use the remote con-

trol tray OPEN/CLOSE (-) button to open the disc tray when the

door is closed. If the disc tray is forcibly prevented from moving,

damage could result.

o Place the main and power supply units in stable locations.

o Do not place anything on top of the main or power supply unit.

o Do not put cloth on top of the units or place them on top of bed-

ding or thick carpet. Doing so could cause them to overheat or

damage them.

o Do not lift or move the main unit during playback because the

disc rotates at high speed. Doing so could damage the disc.

o Always remove any loaded disc before moving the main unit

or packing it for installation in a different location, for example.

Moving the main unit with a disc inside could cause damage.

o The voltage supplied to the power supply unit should match the

voltage as printed on its back. If you are in any doubt regarding

this matter, consult an electrician.

o Do not open the bodies of the units as this might result in dam-

age to the circuitry or cause electric shock. If a foreign object

should get into one of the units, contact your dealer.

o When removing the power plug from an outlet, always pull

directly on the plug. Never pull on the cord itself.

o The ES-LINK format is unique to ESOTERIC and is not compatible

with the HDMI specification. Do not connect the ES-LINK connec-

tor to an HDMI connector on a device made by another company.

Notes about discs

The following marks appear on disc labels and disc cases. This unit

can play discs that have these marks without using an adapter.

This unit cannot play discs that do not have these marks.

Types of discs that can be played on this unit and

their marks

Super Audio CD

Audio CD

If you try to play any other type of disc with this unit, loud

noises that could damage speakers or harm hearing might

occur. Never try to play any type of disc other than those

shown above.

o This unit cannot play DVD video, DVD audio, video CD, DVD-ROM

and CD-ROM discs, for example.

o This unit might not be able to properly play Dual Discs, Copy

Control CDs or other special CDs that do not conform to the

Red Book CD standard. Operation and sound quality cannot be

guaranteed when special discs are used in this unit. If playback of

a special disc should cause trouble, contact the seller of the disc.

CD-R/CD-RW discs

This unit can play CD-R/CD-RW discs that are in audio CD format.

o Be sure to finalize discs created by CD recorders.

Depending on the quality of the disc and the condition of the

recording, playback might not be possible. For details, see the

operation manual for the device you are using.

9

English

Handling discs

o Load discs with their labeled sides up.

(CDs only have one playable side.)

o To remove a disc from its case, always press down on the center of

the case first and then hold the disc by its edges.

Removal from case Holding by edges

o Be careful when handling discs. If the side that contains the data

(unlabeled side) is scratched, smudged with fingerprints or other-

wise dirty or marred, errors could occur during playback.

o If the side of the disc that has the data encoded on it (unlabeled

side) becomes dirty with fingerprints or dust, use a soft cloth to

wipe the surface from the center directly toward the edge.

Always clean discs before storing them. Leaving a disc in an

unclean state might degrade its sound quality.

o Never use record cleaners, antistatic treatments, thinners or similar

chemicals to clean discs. Such chemicals could harm the surface

of the disc.

o Do not leave discs in places that are exposed to direct sunlight or

that are very humid or hot.

o When writing something on the label side of a disc, use a felt-tip

permanent marker. The use of a ballpoint pen or other pen with a

hard tip could damage the disc, making it unplayable.

o After you finish playing a disc, always put it back into its case for

storage. Failure to do so could result in warping or scratches.

o Do not apply labels or other materials to discs. Do not use a disc

that has sticky residue left on its surface after removing tape or a

sticker, for example. If such a disc is loaded, it might become stuck

in the unit or damage the unit.

o Never use commercially-available CD stabilizers. Doing so could

make the disc unplayable or damage the unit.

o Do not use cracked discs because they could damage the unit.

o Never use discs with irregular shapes, including heart-shaped and

octagonal discs, because they could damage the unit.

o Do not use printable discs, which allow printing on the label

side. Since the surface of such a disc has been specially treated, if

loaded, it might become stuck in the unit or damage the unit.

If you have any questions about how to handle a CD-R or

CD-RW disc, contact the manufacturer of the disc directly.

10

Connections (main unit)

AC

AB

D

XLR pin assignment

1. COMMON

2. HOT (+)

3. COLD (−)

Connect using a set

of only one type.

Make the output

connector/format

setting (page25).

Super Audio CD/CD transport (GrandiosoP1X main unit)

GrandiosoD1X

(Left channel)

GrandiosoD1X

(Right channel)

HDMI cable

XLR digital cable

RCA coaxial digital cable

BNC coaxial cable

HDMI cable

10MHz OUT

Device that outputs

clock signal

(GrandiosoG1, etc.)

11

English

A Digital audio output (DIGITAL OUT) connectors

Digital audio is output. Connect one type of these to the digital

input connectors of a D/A converter (such as a GrandiosoD1X).

ES-LINK: HDMI cable

o The ES-LINK format is unique to ESOTERIC and is not compat-

ible with the HDMI specification. Do not connect the ES-LINK

connector to an HDMI connector on a device made by

another company.

Use commercially-available cables for the following

connections.

XLR: XLR digital cable

RCA: RCA coaxial digital cable

o Use one type to connect the unit to the D/A converter(s).

Change the output settings of the connectors according to

the connectors being used (page25).

o We recommend using ES-LINK when connecting to

GrandiosoD1X units.

o When connecting to ESOTERIC D/A converters (GrandiosoD1X/

GrandiosoD1/D-02X/D-05X/D-01/D-02/D-03/D-05/D-07/D-07X)

or D/A converters that support Dual AES, use two cables and

connect this unit’s XLR 1 (L) connector to the left D/A converter

connector and this unit’s XLR 2 (R) connector to the right D/A

converter connector (Dual AES connection).

XLR connectors can be connected in the following two ways.

Single connection (AES/EBU)

This transmits both left and right audio signals through one

signal line.

Dual connection (Dual AES)

This transmits left and right audio signals through separate

signal lines.

B SIGNAL GND grounding terminal

Connecting this grounding terminal to the grounding terminal

of a D/A converter, amplifier or other device might improve the

audio quality.

o This is not an electrical safety ground.

C CLOCK 10MHz IN connector

Use to input 10MHz clock synchronization signals (page14).

When using clock synchronization, connect the clock output

connector of the device outputting the clock signal to the clock

input connector on the main unit.

Then, set the clock (CLK>) setting to SYNC (page26).

Use a commercially available BNC coaxial cable for

connection.

o BNC coaxial cables with 50Ω or 75Ω impedance can be used.

D SOFTWARE maintenance port

This is used for maintenance. Do not connect anything to this

port unless instructed to do so by our service department.

12

V

Precautions when making connections

o After completing all other connections, plug the power plug into a power outlet.

o Read the owner’s manuals of all devices that will be connected, and follow their instructions.

o Be sure to connect the DC power cords with the correct orientation as shown by the arrowhead marks.

Connections (power supply unit)

E E

F

G

B

Main unit

Power supply unit

e Wall outlet

Included power cord

13

English

E DC power input and output (DC IN, DC OUT) connectors

Use both of the included DC (direct current) power cords to con-

nect the DC power input (DC IN) connectors of the main unit

with the DC power output (DC OUT) connectors of the power

supply unit.

DC OUT 1 e DC IN 1

DC OUT 2 e DC IN 2

o The DC power cords have arrows printed on them. Connect

them so that the arrows point in the direction shown in the

illustration on page12.

Check the orientation of the pins and the arrows of each

DC power cord and hold it by its plug. Align the marks on

the plug and the connector and push it in completely until

it clicks into place. When disconnecting, hold the ring and

pull it directly out. When connecting or disconnecting power

cords, do not angle or wiggle the plugs.

o Be sure that the units are off before connecting or discon-

necting a DC power cord.

o Be careful not to pinch your fingers in the ring when con-

necting or disconnecting a DC power cord.

Connector

Align the marks when connecting.

When disconnecting, hold the ring

and pull it directly out.

Plug

V

Never connect this to a P-0, P-01, GrandiosoP1 or

GrandiosoC1 unit.

Doing so could cause damage.

F LED brightness adjustment knob

Turn to adjust the brightness of the power indicator.

G AC power inlet (~IN)

Connect the included AC power cord to this AC inlet. After com-

pleting all other connections, plug the power plug into a power

outlet.

V

Use only a genuine ESOTERIC power cord. Use of

other power cords could result in fire or electric

shock.

V

Disconnect the power plug from the outlet if you

will not use the GrandiosoP1X for a long time.

14

Main unit parts and functions

A MENU button

Press to enter setting mode (page24).

B CLOCK indicator

This shows the clock synchronization status.

When the clock setting is set to SYNC, this will begin to blink.

When a clock signal is detected and synchronization occurs, it

will stop blinking and stay lit.

C Remote control signal receiver

This receives signals from the remote control. When using a

remote control, point the end of it toward this receiver panel

(page16).

D Display

This shows the playback time, the number of tracks and other

information (page23).

E Disc tray

Load a disc for playback here (page18).

F Tray open/close (-) button

Press to open and close the disc tray (page18).

G Stop (8) button

Press to stop playback (page19).

When stopped, press and hold to change the playback area of a

Super Audio CD (page20).

Press when in setting mode to complete changing settings and

show the ordinary display (page24).

H Play (7) button

Press to start disc playback (page18).

During playback, the indicator next to this button lights.

I Pause (9) button

Press to pause playback (page19).

When paused, the indicator next to the play button blinks.

When connected to a GrandiosoD1X using ES-LINK

When stopped, press and hold to change the ES-LINK mode

(page26).

J Skip (.//) buttons

Use to skip to the previous or next track (page21).

Press and hold during playback to search backward/forward.

Repeatedly press and hold to change the backward/forward

search speed (page20).

Use to change parameters when in setting mode (page24).

A C

D F H

I J

EB G

15

English

Power supply unit/display parts and functions

a Disc type

This shows the type of disc that is currently loaded.

SACD: Super Audio CD

CD: Audio CD

o When a hybrid Super Audio CD is loaded, the playback area

type is shown (page20).

b Output

This shows the output connector setting (page25).

o “ESLINK st” is shown when output is ES-LINK stereo mode

(page26).

c Playback/repeat mode

This shows the playback/repeat mode (pages22 and 21).

d Clock mode

This shows the clock setting (page26).

No indicator: CLK set to OFF

CLK: CLK set to SYNC

e Message display area

The playback time and various messages appear here.

SACD

0

:

29

r

T

1

CLK 10M

1

ESLINK

a

e

d

c

b

Display

Power supply unit

K POWER button

Press to turn the GrandiosoP1X on and off.

L Power indicator

This lights blue when the GrandiosoP1X is on.

K L

16

Notes about the remote control

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the main unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

V

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak, which

might result in fire, injury or the staining of nearby materials.

Please read and observe the precautions on page4 carefully.

Precautions when using the remote control

o When using the remote control, point it toward the remote con-

trol signal receiver on the main unit from a distance of 7m (23ft)

or less. Do not place obstructions between the main unit and the

remote control.

o The remote control might not work if the remote control signal

receiver is exposed to direct sunlight or bright light.

o Beware that use of this remote control could cause the unintentional

operation of other devices that can be controlled by infrared rays.

Installing batteries

1 Slide the bottom end of the remote control as

shown in the illustration, and pull out the battery

holder.

2 Insert two AA batteries with ¥ and ^ oriented

as shown in the holder, and put the holder in

again.

3 Slide the bottom end of the remote control as

shown in the illustration to close the battery

holder.

17

English

Remote control parts and functions

The ON and

STANDBY buttons

are not used with

this unit.

If both the main unit and the remote control have buttons

with the same function, we only explain procedures using one

of them in this manual. However, the other can also be used in

the same manner.

a DISPLAY button

During playback or when paused, press this button to change

what is shown on the display (page23).

b Skip (.//) buttons

Use to skip to the previous or next track (page21).

Press and hold during playback to search backward/forward.

Repeatedly press and hold to change the backward/forward

search speed (page20).

Use to change parameters when in setting mode (page24).

c Stop (8) button

Press to stop playback (page19).

Press when in setting mode to complete changing settings and

show the ordinary display (page24).

d PLAY AREA button

When stopped, press to change the playback area of a Super

Audio CD (page20).

e REPEAT button

Use for repeat playback (page21).

f MODE button

Press to enter setting mode (page24).

g Tray open/close (-) button

Press to open and close the disc tray (page18).

h Play (7) button

Press to start disc playback.

i Pause (9) button

Press to pause playback.

Press when paused to start playback.

j AMP buttons

These buttons are not used with this unit. They can be used with

ESOTERIC amplifiers.

k Number buttons

Use for track selection and program playback (pages21 and 22).

l DIMMER button

Use to adjust the brightness of the main unit’s display (page23).

m PLAY MODE button

Press to switch between program and shuffle playback modes

(page22).

18

Basic operation

Playback

1 Press the tray open/close (-) button.

The disc tray comes forward.

2 Place a disc centered on the tray with the labeled

side up.

o If the tray is closed while a disc is outside the center guides,

the disc might become stuck inside and the tray might not

open. Be sure to always place discs within the guides at the

center of the tray.

3 Press the tray open/close (-) button.

The disc tray is drawn into the unit. Be careful not to let your fin-

gers be pinched when the tray closes.

o The unit takes some time to load the disc.

o You can change the disc loading mode (page27).

Turning the GrandiosoP1X on and off

Press the POWER button to turn the GrandiosoP1X on when off or off

when on. When on, the power indicator and the display light.

o Automatic power saving (APS) is set to “30m” by default (page27).

o When using the GrandiosoP1X, turn on the D/A converter(s),

amplifier and other devices that are connected to it.

19

English

4 Press the play (7) button.

Playback starts.

During playback, the indicator near the play button (7) lights

blue.

Pausing playback

During playback, press the pause (9) button to pause playback.

When paused, the indicator next to the play (7) button blinks blue.

Press the play (7) or pause (9) button to restart playback.

Stopping playback

Press the stop (8) button to stop playback.

20

Changing the playback area

Press and hold

Some Super Audio CDs have multiple areas, including stereo (2-channel)

and multichannel. Hybrid Super Audio CDs have two layers with one

containing ordinary CD-quality audio.

When stopped, press and hold the stop (8) button to change the

playback area.

o To change the playback area using the remote control, press the

PLAY AREA button when the unit is stopped.

o The GrandiosoP1X does not support the playback of multichannel

areas on Super Audio CDs.

Switching to ES-LINK mode

To playback an MQA-CD with MQA decoding when connected to

a GrandiosoD1X, the ES-LINK setting must be set to stereo mode

(ESLINK>ST) (page26).

When stopped, press and hold the pause (9) button to change the

ES-LINK setting.

Playback (continued)

Searching backward/forward

Press and hold

During playback, press and hold a skip (.//) button until

searching backward/forward starts. When you find the point where

you want to listen, press the play (7) button.

You can change the backward/forward search speed by repeatedly

pressing and holding the skip (.//) button.

The speed that the < or > blinks on the display also changes.

Low speed Medium speed High speed

Playback at normal speed

La page charge ...

Esoteric Grandioso P1X Le manuel du propriétaire

Esoteric Grandioso P1X Le manuel du propriétaire

dans d''autres langues

Documents connexes