Topdon BT20 Manuel utilisateur

WIRELESS BATTERY LOAD TESTER USER MANUAL

BT20

CONTENTS

SAFETY IS ALWAYS

THE FIRST

PRIORITY!

SECTION 4 TEST

THROUGH

THE TEST BUTTON

SECTION 2

PRODUCT

OVERVIEW

SECTION 6

FAQ

DE

26

28

30

33

34

44

45

EN

5

6

7

8

12

13

22

23

FR

48

50

52

55

56

66

67

ES

70

72

74

77

78

88

89

IT

92

93

94

96

99

100

110

111

114

115

116

117

121

122

132

133

PT

136

138

140

143

144

154

155

RU

158

159

160

161

165

166

176

177

JP

SECTION 1

WHAT'S IN THE

BOX?

SECTION 5 TEST

THROUGH

THE APP BT20

SECTION 8

WARRANTY

SECTION 3 GETTING

STARTED

SECTION 7

TECHNICAL

SPECIFICATION

ENGLISH

For your safety and the safety of others, as well as to

avoid any damage to the product and your vehicle,

carefully read and make sure you fully understand

this manual's safety instructions in its entirety. You

must read the vehicle's service manual, the battery



stated precautions or instructions before and during

any test or service procedure.

ONLY OPERATE TESTS IN A WELL-VENTILATED AREA

since the vehicle produces carbon monoxide (a

toxic, poisonous gas, and particulate matter) when

the engine is running.

ALWAYS BE AWARE OF MOVING PARTS (such as

coolant fans, pulleys, belts) since they spin or turn at

high speeds when the engine is running.

DO NOT TOUCH HOT ENGINE PARTS to prevent

severe burns. The motor parts can get extremely hot

when the engine is running.

TURN THE IGNITION OFF BEFORE CONNECTING OR

DISCONNECTING THE TOOL FROM THE BATTERY

to prevent damage to the tester or the vehicle's

electronic components.

DON'T SMOKE NEAR THE VEHICLE when testing.



ALWAYS WEAR APPROVED SAFETY EYE

PROTECTION to prevent damage from sharp objects

and caustic liquids.

SAFETY IS ALWAYS THE

FIRST PRIORITY!

READ THE INSTRUCTIONS BEFORE USING

EN I 5

DO NOT WEAR LOOSE CLOTHING OR JEWELRY

WHEN WORKING ON AN ENGINE. Loose clothing can

easily be caught in the engine's fan, pulleys, belts,

etc., and jewelry is highly conductive, which may

cause severe burn or electric shock if it contacts

electricity.

DO NOT CUT THE PRODUCTS CORDS OR SUBMERGE

THEM IN WATER. The product is an electrical device

that can cause shock and severe burns.

WARNING: Battery acid is extremely corrosive. If acid

gets into your eyes, RINSE THEM THOROUGHLY WITH

COLD RUNNING WATER FOR AT LEAST 20 MINUTES

AND SEEK MEDICAL ATTENTION IMMEDIATELY.

If battery acid contacts your skin or clothing, WASH

IT IMMEDIATELY WITH A SOLUTION OF WATER AND

BAKING SODA.

SECTION 1

WHAT'S IN THE BOX?

BT20

Quick User Guide

EN I 6

EN I 7

SECTION 2

PRODUCT OVERVIEW

BT20BT20

LCD Display

Test Button

Battery Health

Indicators

Positive Battery Clamp

(Red)

Negtive Battery Clamp

(Black)

Battey Voltage

Indicators

SECTION 3 GETTING STARTED

Where is the battery of a car located?

Let's take the following picture as a reference:

Explanation of LCD Display:

Bluetooth icon. A ashing icon indicates the tester is

not connected to the App; a solid icon indicates the

tester is connected.

This symbol indicates NOT to test twice within 10

seconds.

This symbol indicates voltage is too low. Charge the

battery rst.

This symbol indicates an over temperature. Wait until

the temperature is normal, and then test again.

This symbol indicates a poor connection between the

battery and clamps. Please reconnect.

This symbol indicates the tester reset failed. Please

reconnect the battery and clamps.

This symbol indicates the tester is abnormal or the

battery capacity is beyond the test range. Please

reconnect the battery and clamps, and try again.

EN I 8

1) Most models hold the battery in the engine bay, under the

hood, in one of the front corners. See battery location ① and ②

in Figure 3.1.1.

2) To balance uneven weight distribution, some manufacturers

hold the engine in the trunk. See battery location ⑤, ⑥, and

⑦ in Figure 3.1.1. In this case, the battery may have a plastic

cover that should be removed prior to any testing.

3) For some models, the battery might be stored underneath the

rear seat. See battery location ④ in Figure 3.1.1.

4) For other vehicles, the battery can be located underneath the

passenger seat. See battery location ③ in Figure 3.1.1.

WARNING:

DO NOT TEST THROUGH THE JUMPSTART POSTS. For

models that hold the battery under the seat or in the trunk,

the manufacturer usually includes jumpstart connector

conductor posts under the hood (see Figure 3.1.2) to make

jumpstarting easier. However, to ensure data accuracy and

operation safety, DO NOT CONNECT THE BATTERY TESTER

TO THE JUMPSTART POSTS.

Figure 3.1.1

EN I 9

1) Battery Capacity: 80Ah

Battery Capacity is dened as the total amount of electricity

generated in the battery in a certain time, and is measured in

ampere hours (Ah).

2) Voltage: 12V

When fully charged, automotive batteries should measure

at 12.6 volts. However, this measurement should be from 13.7

to 14.7 volts when the engine is running. If the battery tester

Figure 3.1.2

Figure 3.2.1

How to Identify What Type of Battery You Have?

Let's take the following picture as an example:

Manufacturers

Part No.

80Ah 12v

CCA in USAVoltage

650A(SAE)

AGM

E51

Battery

Type

EN I 10

Battery Capacity

1) Before connecting the clamps to the terminals, please use

sandpaper to polish off the corrosion on the battery terminals.

With this, you can avoid inaccurate test values.

2) Attach the red clamp to the positive (+) terminal, and connect

the black clamp to the negative (-).

• ALWAYS KEEP THE RED & BLACK CLAMPS FROM

TOUCHING.

• ALWAYS DISCONNECT THE NEGATIVE CABLE FROM THE

BATTERY FIRST AND RECONNECT IT LAST.

3) Once the clamps are properly connected, the battery tester

will power on automatically and be ready to conduct tests.

Connect the Clamps to the Battery Terminals (See

Figure 3.3.1)

(Red) (Black)

Figure 3.3.1

reads less than this standard, it means that the battery's

resting voltage is weak. In this case, typically, the battery needs

to be charged or replaced.

3) CCA: 650A (SAE)

The CCA rating refers to how many amps a 12-volt battery

can deliver at 0°F in 30 seconds while maintaining at least a

7.2V voltage. This means that the higher the CCA rating is, the

easier the engine can be cranked in cold temperatures.

EN I 11

SECTION 4 TEST THROUGH

THE TEST BUTTON

Soon after the battery tester is powered on, the real-time voltage

of the battery will be displayed on the screen, and the Bluetooth

icon will ash.

Press the Test Button, and wait for several seconds. The

corresponding Battery Voltage Indicator (FULL / MEDIUM / LOW)

and Battery Health Indicator (GOOD / MEDIUM / BAD) will light

up to show the test result.

Figure 4.1.1

Figure 4.2.1

BT20BT20 BT20BT20

EN I 12

SECTION 5 TEST THROUGH

THE APP BT20

App Downloading and Installation

Home Page

Search "BT20" in the App Store™ or Google Play™, download,

and install it to your mobile device.

Launch the App "BT20" to enter the home page.

① Settings

· Tap [Language] to select your preferred language.

· Tap [Login] to set up your account. (If you would not like to

Tip:

Please allow the App to access your Network and Bluetooth.

Figure 5.2.1

EN I 13

Bluetooth Connection

After connecting the tester to the battery properly and

completing the account setup, tap Connect Bluetooth on the

home page to connect the battery tester to the App.

After a successful connection, the Bluetooth icon on the LCD

display will light up and not ash on and off.

② Bluetooth Connection

③ Battery Test

④ Cranking Test

⑤ Charging Test

⑥ Real-time Voltage

⑦ Test Results by Timeline

Tip:

If you already have a TOPDON account, please directly

log in with it. If you don't have, tap [Register Now] at the

bottom of the [Login] page, register an account with a valid

email address, and then log in.

log in, just skip it.)

Figure 5.3.1

EN I 14

Notes:

1. Only one tester can be connected to the App at a time.

2. Once the Bluetooth is connected, the Test Button on the

battery tester will become unavailable.

WARNING:

Before the test, the engine and all other accessory loads

must be off to ensure accurate results. The battery testing

function only applies to 12V lead-acid batteries.

Battery Test

1) Select Battery Test.

2) Select a battery parameter (CCA or Ah), enter the value, and

tap Next. The specic battery standard is normally listed on

the battery label.

3) Tap Test.

Figure 5.4.1

EN I 15

4) The test result will display as below:

Figure 5.4.2 Figure 5.4.3

Figure 5.4.4

① Back

② Reference Tablet for Test Values

③ Real-time Voltage

EN I 16

④ Loaded Voltage: the voltage measured when turning on the

on-board electrical appliances

⑤ Unloaded Voltage: the voltage measured when turning off the

on-board electrical appliances

⑥ Jump to the page of the real-time voltage waveform

⑦ The CCA/Ah you entered at the previous step

⑧ Test result of Battery Status

⑨ Test result of Voltage

⑩ Tap Save to save the test result to your mobile device as an

image

WARNING:

Before the cranking test, the engine and all other accessory

loads must be off in order to ensure accurate results.

The battery testing function only applies to 12V lead-acid

batteries.

Cranking Test

1) Select Cranking Test.

2) Tap Next.

3) Follow the instructions and start the engine.

Figure 5.5.2 Figure 5.5.3Figure 5.5.1

EN I 17

WARNING:

Always start the engine before performing the charging

test. The battery testing function only applies to 12V lead-

acid batteries.

Charging Test

4) The test result will appear soon.

Figure 5.5.4

① Back

② Real-Time Voltage

③ Test Result

④ Cranking Voltage: the battery voltage while the engine is starting

⑤ Cranking Time: the time a vehicle takes to start an engine

⑥ Tap Save to save the test result to your mobile device as an

image

⑦ Tap Share to share the test result with your coworkers and

clients

1) Select Charging Test.

2) Start the engine and tap OK.

3) Increase the RPM to 2500 and tap OK.

EN I 18

4) Turn on the electronics and tap OK.

5) The test result will appear soon.

① Back

② Real-Time Voltage

③ Test Result

④ Loaded Voltage: The voltage measured when turning on the

on-board electrical appliances

Figure 5.6.1 Figure 5.6.2 Figure 5.6.3 Figure 5.6.4

Figure 5.6.5

EN I 19

⑤ Unloaded Voltage: The voltage measured when turning off

the on-board electrical appliances

⑥ Ripple: A vehicle's battery operates on one-way direct current

(DC) electricity, while alternators output alternating current

(AC) electricity. In this process, the power needs to go through

the diode rectier to turn into a direct current - that's when

the ripple occurs

⑦ Tap Save to save the test result to your mobile device as an

image

⑧ Tap Share to share the test result with your coworkers or

clients

Real-Time Voltage

Select Real-Time Voltage. You can check the real-time voltage

and the recorded voltage waveforms.

Figure 5.7.1 Figure 5.7.2

EN I 20

La page charge ...

Topdon BT20 Manuel utilisateur

Topdon BT20 Manuel utilisateur

dans d''autres langues

Documents connexes