Pro-Temp PT-32-TTC Manuel utilisateur

Marque: Pro-Temp

Modèle: PT-32-TTC

Taper: Manuel utilisateur

Model Numbers

PT-16-TTC / PT-32-TTC / PT-47-TTC

User’s Manual &

Operating Instructions

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH

THIS HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS

OR DAMAGE FROM HAZARDS OF FIRE, EXPLOSION, BURN. ASPHYXIATION, CARBON

MONOXIDE POISONING AND / OR ELECTRIC SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE

OR SERVICE THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS

MANUAL, LABEL, ETC. CONTACT THE MANUFACTURER.

DANGER

CONSUMER: READ AND SAVE THESE INSTRUCTIONS

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR:

The temporary heating of adequately ventilated buildings or

structures under construction, alteration or repair.

FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID

COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR

CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY

THESE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH DO OR MAY

CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE,

SOLVENTS, PAINT THINNERS, DUST PARTICLES OR UNKNOWN CHEMICALS.

WARNING

Factory ID: 522

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (800) 779-3267

Fax: 320-251-2922 • Web: www.protemp.us • Email: [email protected]

PROPANE TANK TOP

HEATER

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Table Of Contents

Safety Information.............................................1-3

Features and Specications.............................4-5

Assembly

.........................................................

6-7

Operation........................................................8-10

Ventilation.............................................................9

Maintenance and Storage..................................10

Troubleshooting Guide.......................................11

Exploded View

..............................................

...

.12

Parts List............................................................13

Warranty.............................................................14

Safety Information

NOT FOR HOME OR RECREATIONAL VEHICLE USE.

WARNING

This is an unvented portable heater. It uses air (oxygen) from the area in which

it is used. Adequate combustion and ventilation air must be provided. Refer to

VENTILATION on Page 6.

WARNING

Carbon Monoxide Hazard This heater produces carbon monoxide, which has no

odor. Burning the heater in an enclosed space can kill you. Never use the heater

in enclosed spaces such as a tent, a camper, any vehicle or recreational vehicle (RV), enclosed

shelter, or any other enclosed areas.

DANGER

Not for use in residential living areas or in non-adequately ventilated enclosed

spaces. Never bring or store a propane cylinder indoors.

DANGER

This heater is designed and approved for use as a construction heater in accordance with Standard

ANSI Z83.7-2011/CSA 2.14-2011. CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU

HAVE ANY QUESTIONS ABOUT APPLICATIONS. Other standards govern the use of fuel gasses

and heating products for specic uses. Your local authority can advise you about these.

If the information in this manual is not followed exactly, a fire or explosion may

result causing property damage, personal injury or loss of life.

DANGER

DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND THOROUGHLY

UNDERSTAND THESE SAFETY AND OPERATING INSTRUCTIONS.

Failure to comply with the precautions and instructions provided with this heater can result in

death, serious bodily injury, property loss or damage from the hazards of fire, explosions, burns,

asphyxiation or carbon monoxide poisoning. Only persons who can read and understand these

instructions should use or service this heater.

WARNING

CALIFORNIA RESIDENTS: This product contains chemicals, including lead,

known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

WARNING

FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY FOR: The temporary

heating of adequately ventilated buildings or structures under construction,

alteration or repair.

WARNING

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Safety Information

The products described in this manual are

propane direct-red heaters. Direct-red means

that all of the combustion products of the heater

enter the heated space. This appliance is rated

at 98% combustion efciency, but does produce

small amounts of carbon monoxide.

Carbon monoxide is toxic. Humans can tolerate

only small amounts of carbon monoxide and so

precautions should be taken to provide proper

ventilation. Failure to provide proper ventilation

in accordance with the instructions in this manual

can result in death.

People with breathing problems should consult a

physician before using this heater.

Early signs of carbon monoxide poisoning

resemble the u. Symptoms of improper

ventilation / carbon monoxide poisoning are:

Headache • Dizziness • Nausea

• Dry Mouth

Sore Throat

• Burning of Nose and Eyes

If you experience any of these symptoms:

GET FRESH AIR AT ONCE! Have your heater

serviced and check for proper ventilation. Some

people are more affected by carbon monoxide

than others. These include: pregnant women,

those with heart or lung problems, anemia or those

under the influence of alcohol or at high altitudes.

FOR OUTDOOR USE. INDOOR USE

PERMITTED ONLY FOR: The temporary

heating of adequately ventilated buildings or

structures under construction, alteration or

repair! Provide at least a three square foot

(2,800 sq cm) opening of outside air for

every 100,000 Btu / Hr heater rating. Refer to

“Ventilation” on page 9 for further instructions.

WHAT TO DO IF THE SMELL OF GAS IS PRESENT:

– DO NOT attempt to light the heater.

– Extinguish any open ame.

– Shut off gas to heater.

– If odor continues, contact your local gas

supplier or re department.

– DO NOT touch or use any electric switch or

any electric device that can cause a spark.

– Immediately call your gas supplier from a

neighbors phone. Follow the gas suppliers

instructions.

– If you can not reach your gas supplier, call

the re department.

– Service must be done by a qualied

service agency.

NEVER store or use gasoline or other ammable

vapors and liquids in the vicinity of this heater.

NEVER store

a propane (LP) cylinder not

connected to this heater in the vicinity of this heater.

NEVER

connect heater to an unregulated gas supply.

NEVER

obstruct the flow of combustion and

ventilation air. (The front and rear of heater).

NEVER use duct work in front or rear of heater.

NEVER modify this heater or operate a heater that

has been modified.

NEVER service, move or handle heater while still

hot or operating

NEVER use heater in occupied dwellings.

NEVER use heater in a tent.

RISK OF INDOOR AIR

POLLUTION!

WARNING

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

DANGER

RISK OF BURNS, FIRE AND

EXPLOSION!

WARNING

PROPANE IS AN

EXPLOSIVE GAS!

DANGER

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Keep all combustible materials away from this heater.

Minimum Clearance From Combustibles

Sides Top Front Rear

36 in. 60 in. 60 in. 36 in.

ALWAYS install the heater so that it is not directly

exposed to water spray, rain, dripping water, or wind.

ALWAYS provide adequate clearance for

accessibility, combustion and ventilation (air supply)

while heater is operating.

– Use heater in accordance with all local codes.

In the absence of local codes, refer to The

National Fuel Code, ANSI Z223.1.

– This heater is shipped from the factory

for use with propane (LP) gas only. Do not

convert to any other gas. Installation must

conform to local codes, or in their absence,

with the standard for the Storage and

Handling of Liquefied Petroleum Gases ANSI/

NFPA 58 and the Natural Gas and Propane

Installation Code CSA B149.1.

– Gas supply connections should be checked

by using a 50/50 soap and water solution.

Never use a ame to check for gas leaks.

– Do not direct heater discharge towards the LP

cylinder unless it is at least 20 feet from the

heater.

– Use only the regulator and hose assembly

provided with this heater. Inspect the

regulator/hose assembly prior to each use of

the heater. If there is excessive abrasion or

wear, or if the hose is cut, replace it with the

proper assembly shown in the parts list, prior

to using the heater.

Minimum and Maximum Inlet Pressure

PT-16-TTC PT-32-TTC PT-47-TTC

Min. 5 PSI

Max. 200 PSI

Safety Information

The hose assembly shall be

pro tected from traffic, building

material and contact with hot surfaces both

during use and while in storage.

WARNING

RISK OF FIRE! ALWAYS ATTACH THE HEATER IN AN UPRIGHT VERTICAL

POSITION. ALWAYS LOCATE HEATER ON A STABLE AND LEVEL SURFACE!

WARNING

CAUTION! HOT WHILE IN

OPERATION. DO NOT TOUCH.

KEEP CHILDREN, ANIMALS, CLOTHING AND

COMBUSTIBLES AWAY FROM HEATER.

WARNING

For use with propane (LP)

gas only.

WARNING

DO NOT use any LP cylinder

larger than 20 lbs.

WARNING

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Features

PT-16-TTC

Regulator

Figure 1

Specications

Model # PT-16-TTC PT-32-TTC PT-47-TTC

BTU 12 / 14 / 16,000 25 / 28 / 32,000 36 / 40 / 47,000

Fuel Consumption (Lbs./hr) .56 / .65 / .74 1.16 / 1.30 / 1.49 1.67 / 1.86 / 2.18

Maximum Operating Hours 35.9 / 30.8 / 27.0 17.2 / 15.4 / 13.4 12.0 / 10.8 / 9.2

Required Cylinder Lbs. 20 20 20

Fuel Type Propane Propane Propane

Heating Area (Ft.

) 300 / 350 / 400 620 / 700 / 800 900 / 1000 / 1175

Specications subject to change without notice.

Missing Parts? Please Call 800-779-3267 For Assistance

Front Guard

Heat Reector

Rear Guard

Ignition Hole

Tip Over Switch

Safety Valve

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Features

PT-32-TTC

Regulator

Figure 2

Front Guard

Heat Reector

Rear Guard

Ignition Hole

Tip Over Switch

Safety Valve

Features

PT-47-TTC

Figure 3

Mounting Bolt Knob

Hose

Front Guard

Heat Reector

Safety Valve

Mounting Bolt Knob

Hose

Rear Guard

Ignition Hole

Regulator

Tip Over Switch

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Assembly

Model PT-32-TTC:

Tools Needed:

– Medium Phillips head screwdriver.

1. Place the tank collar bracket on top of the

center plate. Be sure the mounting bolt knob is

on bottom as shown in Figure 4

2. Insert machine screw into top hole using

Phillips head screwdriver.

3. Insert 2nd machine screw into bottom hole.

This will secure the tank collar bracket to the

center plate.

Model PT-47-TTC:

Tools Needed:

– Medium Phillips head screwdriver.

1. Insert the mounting bolt knob into the tank

collar bracket.

2. Place tank collar bracket on the swivel bracket.

3. Place the plane washer on the tank collar

bracket and then insert the support bolt.

(See Figure 5)

4. See Figure 6 on page 7 for determining burner

position options.

DO NOT adjust burner heads while heater is operating.

WARNING

Regulator

Knob

Fuel Connector Nut

Machine

Screws

Mounting Bolt Knob

Tank Collar Bracket

Tip over Switch

Assembly

Swivel

Manifold

Mounting

Bolt Knob

Plane Washer

Wing Nut

Regulator

Knob

Fuel Connector Nut

Tank Collar Bracket

Swivel Bracket

Figure 4 Figure 5

Missing Parts? Please Call 800-779-3267 For Assistance

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Assembly

PT-47-TTC (Continued):

– To have all 3 burners face front, the plane

washer should be to the right side of tank collar

bracket. (See Figure 6)

– To have far left burner face back, the plane

washer should be to the left side of tank collar

bracket. (See Figure 6)

Figure 6

Connecting Heater to LP Cylinder:

Be sure to read and understand all of the Safety

Information in this manual before connecting

the heater to the LP cylinder. Installation must

conform to local codes and with the Standard

for the Storage and Handling of Liquefied

Petroleum Gasses and ANSI/NFPA 58.

Inspect the hose and regulator prior to each use

of the heater. If there is excessive abrasion or

wear, or if the hose is cut, replace it with the

proper assembly shown in the parts list prior to

using the heater.

Model PT-16-TTC:

1. Be sure that the control knob on the regulator

is in the “OFF” position.

2. Line up the threads on the fuel connector nut

with the threads on the LP cylinder valve. Turn

fuel connector nut COUNTERCLOCKWISE to

tighten. Fully tighten the nut, being careful not

to over tighten.

3. Slowly open the LP cylinder valve.

Models PT-32-TTC / PT-47-TTC:

1. Be sure that the control knob on the regulator

is in the “OFF” position.

2. Line up the slots in the tank collar bracket

with the tank collar ring and slide into place.

Be sure the mounting knob is to the outside,

and tighten.

3. Line up the threads on the fuel connector nut

with the threads on the LP cylinder valve. Turn

fuel connector nut COUNTERCLOCKWISE to

tighten. Fully tighten the nut, being careful not

to over tighten.

4. Slowly open the LP cylinder valve.

Check all connections for leaks using a 50/50

mixture of dish-soap and water. Any bubbles

that appear show a leak. Remove and

reconnect the Connector Nut to the valve.

DO NOT direct the heater

discharge towards any

propane cylinder located within 20 feet of

the heater.

WARNING

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Operation

Propane Supply / Information:

Propane (LP)

This heater is not supplied with a propane cylinder.

Use only an approved propane cylinder.

LP Characteristics

– Flammable, explosive under pressure, heavier

than air and pools in low areas.

– In its natural state, propane has no odor, but

for your safety an odor that smells like rotten

cabbage has been added.

– Contact of propane (LP) gas with the skin can

cause freeze burns.

– Heater is manufactured for use with propane

gas only. DO NOT attempt to convert to any

other gas. Such modications are dangerous

and will void the warranty.

– When heater is not in use, LP Cylinder must be

turned OFF.

– Be sure that the LP Cylinder is located on a

level and stable surface.

– DO NOT use this heater in a basement or

below ground level. Propane is heavier than

air and will always seek the lowest level. If you

suspect a leak, shut off the valve at the LP

Cylinder immediately.

The Propane (LP) cylinder must also be

equipped with the following

– A collar to protect the gas valve.

– A shut-off valve terminating a LP cylinder valve

outlet as specied in the American National

Standard for Compressed Gas Cylinder Valve

Outlets and Inlets Connections.

– A safety relief valve having direct

communications with the vapor space of the LP

cylinder.

– The heater must operate on vapor withdrawal

from the operating cylinder.

– The amount of Propane (LP) used with this

heater varies. Both factors are

– The amount of gas in the cylinder of LP.

– The temperature of the LP tank and its

surroundings.

– Always keep LP cylinder fastened and upright.

– Avoid tipping the LP cylinder on its side when

connected to a regulator, since this may

cause damage to diaphragm in the regulator.

– Handle valves with care.

– Never connect an unregulated LP cylinder to

a construction heater.

– DO NOT subject LP cylinder to excessive heat.

– Tightly close the gas shutoff valve on the LP

cylinder after each use.

– All ttings must be protected when

disconnected from the LP cylinder.

– Never store an LP cylinder inside a building or

in the vicinity of a gas burning appliances.

Propane is safe to use when

properly handled. Careless

handling of the LP cylinder could result in a

fire and or an explosion.

CAUTION

The disconnected tank must

never be stored in a building,

garage or any other enclosed area.

CAUTION

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Operation

Lighting Instructions:

Models PT-16-TTC / PT-32-TTC / PT-47-TTC

Ventilation

– Risk of indoor air pollution and Carbon

Monoxide Poisoning.

– Refer to Safety Information on pages 1-3

for information about Carbon Monoxide

Poisoning.

– ALWAYS provide a fresh air opening in the

heated space of at least three square feet

(2,800 sq. cm) for each 100,000 BTU / Hr.

of heater output. Provide a larger opening if

more heaters are being used.

Minimum Ventilation Opening Needed

PT-16-TTC PT-32-TTC PT-47-TTC

0.5 ft.

1.0 ft.

1.4 ft.

460 cm

920 cm

1300 cm

1. STOP! Be sure to read all of the Safety

Information (See pages 1-3).

– ALWAYS Stand to the side or rear of the

heater.

– ALWAYS keep face and other body parts

away from the heater.

2. Check that the valve and propane cylinder

is open.

3. Turn the heater regulator knob CLOCKWISE

to the (OFF) position.

4. Wait five (5) minutes for any gas to clear.

Smell for gas around the heater, including

near the floor. If you do smell gas STOP!

Follow the safety instructions and check

leaks. If there is no gas smell proceed to the

next step.

5. Turn the regulator knob

COUNTERCLOCKWISE to the “HI” position.

6. Insert a lit match into the ignition hole in the

reflector. (See Figure 7)

7. Press the safety shut-off valve plunger for five

(5) seconds.

8. Mesh burner will light and glow red.

(Continued on Page 10)

CARBON MONOXIDE POISONING

MAY LEAD TO DEATH!

DANGER

Be sure to read and understand

all of the Safety Information in

this manual before lighting this heater.

WARNING

Heater has high surface

temperatures. Be sure to

keep children, pets and clothing away from

the heater. Be sure to keep burner and

heater regulator clean and free from any

debris. Maintain safe distances from heater

as shown on Page 3.

CAUTION

NEVER use a flame to check

for leaks!

WARNING

Ignition Hole

Safety Shut-OFF

Valve Plunger

Heat Regulator Knob

Figure 7

NEVER look over the top of

the heater (reflector). There

is a potential for a small flash of flame during

ignition that can cause serious bodily injury.

ALWAYS stand to the side or rear of the heater

during ignition. DO NOT allow any body part

to touch the heater or be in front of the heater

during ignition.

WARNING

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Operation

Lighting Instructions

Models PT-16-TTC / PT-32-TTC / PT-47-TTC (CONT)

9. Once lit, keep the plunger depressed for thirty

(30) seconds. Then release the plunger, and

if the burner stays lit, remove and extinguish

the match. You will know that the burner is lit

when the mesh screen begins to glow red.

10. If the burner does not stay lit, repeat the

lighting process. If the heater does not light

after several attempts, be sure you are getting

fuel to the burner. The faint smell of gas will

tell you if the fuel is flowing. If not, there may

be a problem with your LP cylinder. Take it

back to your local dealer for replacement.

11. Once the burner is lit, turn Regulator Control

Knob to desired setting (HI) / (MED) / (LO ).

12. Light all burners when maximum heat is

desired. Follow Lighting Instructions steps

1-11. The second and third burner should be

lit separately. Do Not Attempt to light second

burner off the first burner. Be sure NOT to

point burners at one another.

To Turn Off Heater

1. Turn the valve on the LP cylinder CLOCKWISE

to stop the flow of fuel.

2. Turn the heater regulator knob to the (OFF)

position and wait at least fifteen (15) minutes for

the heater to cool.

3. Tightly close the gas shutoff valve on the LP

cylinder after each use.

4. Remove the heater from the LP cylinder by

reversing the steps in Connecting Heater to

LP Cylinder on Page 7. DO NOT store the LP

cylinder with the heater still attached or in an

enclosed area.

NOTE: ALWAYS INSPECT HEATER BEFORE

USE AND AT LEAST ANNUALLY BY A

QUALIFIED SERVICE PERSON.

EXTREMELY HOT during

operation. Do Not touch any

metal components while in operation. Keep

gasoline and any other flammable liquids

away from the heater.

DANGER

Never bring or store a

propane cylinder indoors.

DANGER

DO NOT insert the lit match

into the air inlet holes in the

mixing tube.

CAUTION

Maintenance and Storage

1. Inspect your heater before each use.

Check all connections for leaks, following

the procedure outlined on Pages 7 and 8.

Check the Regulator Hose (dual burner

models only) for any cracks, breaks or wear.

If the hose is damaged replace it with the

correct manufacturers part. Heater should be

inspected before each use and once annually

by a qualied service person.

2. After use, always disconnect the heater

from the LP cylinder, and store the heater

separately from the tank. Be sure to close

the tank valve after use, and before storage.

The LP cylinder should be stored outdoors in

accordance with chapter 5 of the Standard for

Storage and Handling of Liqueed Petroleum

Gases (ANSI/INFPA 58).

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Troubleshooting Guide

Locating Your Serial Number:

Your serial number can be found in the bottom left hand corner of the heater’s instruction hang-tag. It

will begin with the letters “PGTT” followed by 8 digits. For Example: PGTT12345678. Have your Se-

rial Number ready before calling customer service at 800-779-3267.

Problem Possible Cause(s) Solution

Unit will not light.

1. Valve on propane cylinder

closed.

2. Propane cylinder empty.

3. Regulator not in (HI) position.

4. Defective regulator

1. Open cylinder valve by turning

COUNTERCLOCKWISE.

2. Rell cylinder.

3. Turn regulator to (HI) position.

4. Replace regulator assembly.

Burner will not stay lit

when gas valve plunger

is released

1. Tip switch activated or

defective.

2. Wire terminal connections

unplugged.

3. Defective thermocouple.

4. Defective MPU.

1. Place heater in upright position

or replace tip switch.

2. Check wiring connections.

3. Replace thermocouple.

4. Replace MPU.

Excessive ames coming

out of burner, not glowing

red. Flames ashback

/ burn inside the mixing

tube.

1. Air inlet holes blocked or

covered.

2. Burner screen damaged.

3. Gap between burner screen

and burner can.

1. Clear any obstructions

2. Replace Burner screen.

3. Replace or repair burner head

assembly.

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Exploded View

Figure 8

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

Parts list

Item

Description PT-16-TTC PT-32-TTC PT-47-TTC

1 Hose Assembly ‒ 20-051-0001 20-051-0002

2 Thermocouple 20-091-0002 20-091-0002 20-091-0002

3 Mounting Bolt Knob ‒ 20-503-0001 20-503-0001

4 Tipover Switch 50-017-0001 50-017-0001 50-017-0001

NEVER LEAVE HEATER UNATTENDED

WHILE BURNING OR WHILE CONNECTED

TO A FUEL SOURCE

LIMITED WARRANTY

Pinnacle Climate Technologies, Inc. warrants this heater

to the original retail purchaser only, to be free from defects

in material and workmanship for a period of one (1) year

from the date of initial purchase. This product must be

properly installed, maintained and operated in accordance

with the instructions provided.

Pinnacle Climate Technologies, Inc. requires reasonable

proof of your date of purchase from an authorized retailer

or distributor. Therefore, you should keep your sales slip,

invoice or cancelled check from the original purchase.

This Limited Warranty shall be limited to the repair or

replacement of parts, which prove defective under normal

use and service within the warranty period, and which

Pinnacle Climate Technologies, Inc. shall determine at its

reasonable discretion.

This warranty does not apply to products purchased for

rental use.

This Limited Warranty does not cover any failures or

operating difculties due to normal wear and tear, accident,

abuse, misuse, alteration, misapplication, improper

installation or improper maintenance and service by you

or any third party. Failure to perform normal and routine

maintenance on the heater, shipping damage, damage

related to insects, birds or animals of any kind, and damage

due to weather conditions are also not covered.

In addition, the Limited Warranty does not cover damage

to the nish, such as scratches, dents, discoloration, rust or

other weather damage, after purchase.

All transportation costs for the return of damaged product

or parts will be the responsibility of the purchaser. Upon

receipt of damaged item, Pinnacle Climate Technologies,

Inc. will examine the item and determine if defective.

Pinnacle Climate Technologies, Inc. will repair or replace

and return the item, freight pre-paid.

If Pinnacle Climate Technologies, Inc. nds the item to

be in normal operating condition, or not defective the item

will be returned freight collect. This Limited Warranty is

in lieu of all other express warranties. Pinnacle Climate

Technologies, Inc. disclaims al warranties for products

that are purchased from sellers other than authorized

dealers or distributors.

AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS

WARRANTY EXPIRES, Pinnacle Climate Technologies,

Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

APPLICATION. FURTHER, Pinnacle Climate Technologies,

Inc. SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER

OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE

INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Pinnacle

Climate Technologies, Inc. assumes no responsibility for

any defects caused by third parties. This Limited Warranty

gives the purchaser specic legal rights; a purchaser may

have other rights depending upon where he or she lives.

Some states do not allow the exclusion or limitation of

special, incidental or consequential damages, or limitations

on how long a warranty lasts, so the above exclusion and

limitations may not apply to you.

Pinnacle Climate Technologies, Inc. does not authorize

any person or company to assume for it any other

obligation or liability in connection with the sale, installation,

use, removal, return or replacement of its equipment, and

no such representations are binding on Pinnacle Climate

Technologies, Inc.

Always be sure to specify the model number and serial

number when making any claim with Pinnacle Climate

Technologies, Inc. For your convenience, use the space

provided below to list this information.

Model #:________________________________

Serial #:________________________________

Date of Purchase: ________________________

Locating Your Serial Number:

Your serial number can be found in the bottom left hand corner of the heater’s instruction hang-tag. It will begin

with the letters “PGTT” followed by 8 digits. For Example: PGTT12345678. Have your Serial Number ready

before calling customer service at 800-779-3267.

XXX-XXXXXXXX

Serial Number Label

1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free (800) 779-3267

Fax: 320-251-2922 • Web: www.protemp.us • Email: [email protected]

Modelos N.°

PT-16-TTC / PT-32-TTC / PT-47-TTC

ADVERTENCIA GENERAL DE PELIGRO:

SI NO CUMPLE CON LAS PRECAUCIONES Y LAS INSTRUCCIONES QUE SE LE PROPORCIONAN

CON ESTE CALENTADOR, PUEDE PROVOCAR LA MUERTE, LESIONES CORPORALES GRAVES Y

DAÑOS MATERIALES O DAÑOS POR PELIGRO DE INCENDIO, EXPLOSIÓN, QUEMADURAS, ASFIXIA,

INTOXICACIÓN POR MONÓXIDO DE CARBONO O DESCARGA ELÉCTRICA.

ESTE CALENTADOR SOLAMENTE LO DEBEN USAR O DARLE MANTENIMIENTO PERSONAS QUE

PUEDAN COMPRENDER Y SEGUIR LAS INSTRUCCIONES.

SI NECESITA AYUDA O INFORMACIÓN SOBRE EL CALENTADOR, COMO UN MANUAL DE

INSTRUCCIONES, ETIQUETAS, ETC., PÓNGASE EN CONTACTO CON EL FABRICANTE.

PELIGRO

CONSUMIDOR: LEA Y CONSERVE ESTAS INSTRUCCIONES

PARA USO EN EXTERIORES. EL USO EN INTERIORES SÓLO SE

PERMITE PARA: Calefacción temporal de edificios adecuadamente

ventilados o estructuras en construcción, modificación o reparación.

PELIGRO DE INCENDIO, QUEMADURAS, INHALACIÓN Y EXPLOSIÓN. MANTENGA

LOS COMBUSTIBLES SÓLIDOS, COMO MATERIALES DE CONSTRUCCIÓN, PAPEL

O CARTÓN, A UNA DISTANCIA PRUDENTE DEL CALENTADOR SEGÚN LO RECOMIENDAN ESTAS

INSTRUCCIONES. NUNCA USE EL CALENTADOR EN ESPACIOS QUE CONTENGAN O PUEDAN

CONTENER COMBUSTIBLES VOLÁTILES O SUSPENDIDOS EN EL AIRE NI PRODUCTOS COMO

GASOLINA, DISOLVENTES, SOLVENTES DE PINTURA, PARTÍCULAS DE POLVO O SUSTANCIAS

QUÍMICAS DESCONOCIDAS.

ADVERTENCIA

ID de fábrica: 522

1 Industrial Blvd #101, Sauk Rapids, MN 56379, EE. UU. • Llamada sin costo: (800) 779-3267

Fax: 320-251-2922 • Web: www.protemp.us • Correo electrónico: inf[email protected]

Manual del usuario e

Instrucciones de operación

CALENTADOR CON

TANQUE DE PROPANO

NUNCA DEJE DESATENDIDO EL CALENTADOR

MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ

CONECTADO A UNA FUENTE DE COMBUSTIBLE

Índice

Información sobre seguridad ............................1-3

Características y especicaciones

...................4-5

Montaje

...........................................................

6-7

Operación

.......................................................8-10

Ventilación

...........................................................9

Mantenimiento y almacenamiento

..................... 10

Guía de solución de problemas

.........................11

Vista detallada

..................................................

Lista de piezas...................................................13

Garantía.............................................................14

Información de seguridad

NO DEBE USARSE EN CASAS NI EN VEHÍCULOS DE USO RECREATIVO.

ADVERTENCIA

Este es un calentador portátil sin ventilación. La unidad utiliza el aire (oxígeno) del

espacio donde se usa. Será necesario suministrar suficiente aire para la combustión y la

ventilación. Consulte VENTILACIÓN en la página 6.

ADVERTENCIA

Riesgo de inhalación de monóxido de carbono Este calentador produce monóxido

de carbono, que es un gas inodoro. Encender el calentador en un espacio cerrado

puede ocasionarle la muerte. Nunca use el calentador en espacios cerrados, como tiendas de campaña,

remolques, cualquier tipo de vehículo (entre ellos, vehículos de uso recreativo), albergues cerrados o

cualquier otra área cerrada.

PELIGRO

No debe usarse en áreas habitables residenciales ni en espacios cerrados con ventilación

inadecuada. Nunca ingrese o almacene un tanque de propano en espacios interiores.

PELIGRO

Este calentador está diseñado y aprobado para uso en construcciones de acuerdo con la norma ANSI

Z83.7-2011/CSA 2.14-2011. CONSULTE CON LAS AUTORIDADES DE SEGURIDAD DE INCENDIOS DE

SU LOCALIDAD SI TIENE ALGUNA DUDA SOBRE EL USO DE ESTE CALENTADOR. Otras normas rigen

el uso de gases combustibles y productos de calefacción para usos especícos. Sus autoridades locales

pueden asesorarle sobre esas normas.

Si no sigue la información de este manual al pie de la letra, puede producirse un incendio

o una explosión que provoquen daños materiales, lesiones físicas o pérdida de la vida.

PELIGRO

NO USE ESTE CALENTADOR HASTA HABER LEÍDO Y COMPRENDIDO TOTALMENTE

ESTAS INSTRUCCIONES DE SEGURIDAD Y OPERACIÓN.

El no cumplir con las precauciones e instrucciones proporcionadas con este calentador puede resultar en

muertes, lesiones graves, daños materiales o daños por peligro de incendio, explosiones, quemaduras,

asfixia o envenenamiento por monóxido de carbono. Solamente personas que puedan leer y comprender

estas instrucciones deben usar o dar servicio a este calentador.

ADVERTENCIA

RESIDENTES DE CALIFORNIA: Este producto contiene sustancias químicas, incluyendo

plomo, conocidas en el estado de California como causantes de defectos de nacimiento u

otros daños reproductivos. Lávese las manos después de manipularlo.

ADVERTENCIA

PARA USO EN EXTERIORES. EL USO EN INTERIORES SÓLO SE PERMITE

PARA: Calefacción temporal de edificios adecuadamente ventilados o estructuras en

construcción, modificación o reparación.

ADVERTENCIA

NUNCA DEJE DESATENDIDO EL CALENTADOR

MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ

CONECTADO A UNA FUENTE DE COMBUSTIBLE

Información de seguridad

Los productos descritos en este manual son

calentadores de fuego directo de gas propano.

Fuego directo signica que todos los productos de

combustión del calentador ingresan en el espacio

calentado. Este aparato tiene una clasicación de

98% de eciencia de combustión, pero produce

pequeñas cantidades de monóxido de carbono.

¡LA INTOXICACIÓN POR MONÓXIDO

DE CARBONO PUEDE CONDUCIR

A LA MUERTE!

PELIGRO

El monóxido de carbono es tóxico. Los seres

humanos solo pueden tolerar pequeñas cantidades

de monóxido de carbono, así que deben tomarse las

medidas de precaución necesarias para suministrar

una ventilación adecuada. No proporcionar la

ventilación adecuada de acuerdo con este manual

puede ocasionar la muerte.

Las personas con problemas respiratorios deben

consultar con un médico antes de usar el calentador.

Los primeros síntomas de envenenamiento por

monóxido de carbono se parecen a los de la

gripe. Los síntomas de ventilación inadecuada o

envenenamiento por monóxido de carbono son:

Dolor de cabeza • Mareo • Náusea • Boca seca

Dolor de garganta • Irritación de la nariz y los ojos

Si tiene alguno de estos síntomas:

¡SALGA AL AIRE LIBRE DE INMEDIATO! Haga

revisar su calentador y compruebe que la ventilación

sea la adecuada. Algunas personas se ven más

afectadas que otras por el monóxido de carbono.

Por ejemplo: mujeres embarazadas, personas con

problemas pulmonares o cardíacos, anemia o bajo la

influencia del alcohol o en grandes altitudes.

PARA USO EN EXTERIORES. EL USO EN

INTERIORES SÓLO SE PERMITE PARA:

Calefacción temporal de edificios adecuadamente

ventilados o estructuras en construcción,

modificación o reparación. Proporcione una

abertura de al menos tres pies cuadrados (2800 cm

cuadrados) al aire exterior por cada 100,000 Btu/h

que genere el calentador. Consulte “Ventilación”

en la página 9 para obtener más instrucciones.

¡EL PROPANO ES UN GAS

EXPLOSIVO!

PELIGRO

QUÉ HACER SI PERCIBE OLOR A GAS:

– NO trate de encender el calentador.

– Apague toda clase de ama abierta.

– Cierre el suministro de gas del calentador.

– Si continúa el olor, póngase en contacto

con la empresa de gas o el departamento de

bomberos de su localidad.

– NO toque ni utilice interruptores de electricidad

ni dispositivos eléctricos que pudieran

provocar una chispa.

– Llame inmediatamente a la empresa de gas

desde el teléfono de un vecino. Siga las

instrucciones de la empresa de gas.

– Si no puede comunicarse con la empresa de

gas, llame al departamento de bomberos.

– Solo una dependencia de servicio calicada

puede hacer la reparación.

¡RIESGO DE QUEMADURAS,

INCENDIO Y EXPLOSIÓN!

ADVERTENCIA

NUNCA almacene ni use gasolina ni otros vapores y

líquidos inamables en las cercanías de este aparato.

NUNCA almacene

tanques de propano (LP) que no

se encuentren conectados a este calentador en los

alrededores del mismo.

NUNCA

conecte el calentador a un suministro de gas

no regulado.

NUNCA

obstruya el flujo del aire de combustión y

ventilación. (La parte frontal y posterior del calentador).

NUNCA use conductos en la parte frontal o posterior

del calentador.

NUNCA modifique el calentador ni utilice un

calentador que haya sido modificado.

NUNCA dé servicio, mueva ni manipule al calentador

mientras está caliente o funcionando.

NUNCA use el calentador en viviendas habitadas.

NUNCA use el calentador en tiendas de campaña.

¡RIESGO DE CONTAMINACIÓN

DEL AIRE INTERIOR!

ADVERTENCIA

NUNCA DEJE DESATENDIDO EL CALENTADOR

MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ

CONECTADO A UNA FUENTE DE COMBUSTIBLE

Mantenga todos los materiales combustibles lejos de

este calentador.

Separación mínima entre el calentador y

materiales combustibles

Lados Superior Frente Atrás

36 pulg. 60 pulg. 60 pulg. 36 pulg.

SIEMPRE instale el calentador de modo que no esté

expuesto directamente a rocío de agua, lluvia, goteo

de agua o viento.

SIEMPRE proporcione el espacio adecuado para la

accesibilidad, la combustión y la ventilación (entrada

de aire) mientras el calentador está funcionando.

Para usarse con gas propano (LP)

únicamente

ADVERTENCIA

NO use tanques de LP de más

de 20 lb.

ADVERTENCIA

– Use el calentador de acuerdo con todos los

códigos locales. En ausencia de códigos locales,

consulte el Código Nacional de Combustibles,

ANSI Z223.1.

– Este calentador se envía de la fábrica para

uso con gas LP (propano) únicamente. No lo

convierta a ningún otro gas. La instalación debe

cumplir con los códigos locales o, a falta de

ellos, con la norma para el almacenamiento y la

manipulación de gases licuados de petróleo ANSI/

NFPA 58 y el Código de instalación de gas natural

y gas propano CSA B149.1.

– Las conexiones de suministro de gas deben

revisarse usando una solución de 50/50 de agua

y jabón. Nunca use una llama para vericar si hay

fugas de gas.

– No oriente la descarga del calentador hacia el

tanque de LP a menos que éste se encuentre a

una distancia de 20 pies (6 m) del calentador.

– Utilice únicamente el conjunto de regulador y

manguera suministrado con este calentador.

Inspeccione el conjunto del regulador y manguera

antes de cada uso del calentador. Si está

demasiado desgastado, o si la manguera está

cortada, reemplace con el conjunto correcto

mostrado en la lista de piezas, antes de usar

el calentador.

Presión de entrada mínima y máxima

PT-16-TTC PT-32-TTC PT-47-TTC

Mín. 5 PSI

Máx. 200 PSI

Información de seguridad

El conjunto de la manguera

deberá estar protegido del

tráfico, de material de construcción y de

contacto con superficies calientes, tanto al

usarse como al tenerlo almacenado.

ADVERTENCIA

¡RIESGO DE INCENDIO! CONECTAR SIEMPRE EL CALENTADOR EN POSICIÓN

VERTICAL Y RECTA. ¡COLÓQUELO SIEMPRE SOBRE UNA SUPERFICIE ESTABLE

Y NIVELADA!

ADVERTENCIA

¡PRECAUCIÓN! CALIENTE

MIENTRAS ESTÉ EN

FUNCIONAMIENTO. NO LO TOQUE. MANTENGA

A NIÑOS, ANIMALES, ROPA Y COMBUSTIBLES

LEJOS DEL CALENTADOR.

ADVERTENCIA

La page charge ...

Pro-Temp PT-32-TTC Manuel utilisateur

Marque: Pro-Temp

Modèle: PT-32-TTC

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

español: Pro-Temp PT-32-TTC Manual de usuario

Pro-Temp PT-32-TTC Manuel utilisateur

Pro-Temp PT-32-TTC Manuel utilisateur

dans d''autres langues

Autres documents