Paradigm PW 300 Manuel utilisateur

OWNER’S MANUAL

+

–

PW 300

RECYCLING AND REUSE GUIDELINES FOR EUROPE

In accordance with the European Union WEEE

(Waste Electrical and Electronic Equipment)

directive effective August 13, 2005, we would like to

notify you that this product may contain regulated

materials which, upon disposal, according to the WEEE

directive, require special reuse and recycling processing.

For this reason Paradigm Electronics Inc. (manufacturers of

Paradigm speakers and Anthem Electronics) has arranged

with our distributors in European Union member nations to

collect and recycle this product at no cost to you. To find your

local distributor please contact the dealer from whom you

purchased this product or go to our website at paradigm.com.

Please note that the product only falls under the WEEE

directive. When disposing of packing and other shipping

material we encourage you to recycle through the

normal channels.

FCC ID: 2AJAAPW 300ST and IC ID: 21761PW 300BT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including

information that may cause undesired operation. Changes or

modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the

equipment.

This product has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This product generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

product does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician

for help.

This device complies with Industry Canada licence-exempt

RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation of the

device.

WIRELESS TRANSMITTER COMPLIANCE INFORMATION

The term “IC” before the radio certification number only

signifies that Industry Canada technical specifications were

met. This equipment complies with FCC and IC radiation

exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with

minimum distance 20 cm between the radiator and your

body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter. To reduce

potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that

permitted for successful communication.

PARADIGM ELECTRONICS RESERVES THE RIGHT TO

CHANGE SPECIFICATIONS AND/OR FEATURES WITHOUT

NOTICE AS DESIGN IMPROVEMENTS ARE INCORPORATED.

PARADIGM and ANTHEM are registered trademarks of

Paradigm Electronics Inc. PW 300, PW Soundbar, and ARC

are trademarks of Paradigm Electronics Inc. Copyright

products and services mentioned may be trademarks or

service marks of their respective owner(s).

Apple and the Apple logo are trademarks of Apple Inc.,

registered in the U.S. and other countries. App Store is a

service mark of Apple Inc.

Windows

®

is a registered trademark of Microsoft Corporation in

the United States and other countries.

Amazon, Kindle, Fire, and all related logos are trademarks of

Amazon.com, Inc. or its affiliates.

Android is a trademark of Google Inc.

Google Play is a trademark of Google Inc.

The Spotify software is subject to third party licenses found

here: www.spotify.com/connect/third-party-licenses.

For DTS patents, see http://patents.dts.com. Manufactured

under license from DTS Licensing Limited. DTS, Play-Fi, the

Symbol, and Play-Fi together in combination with the Symbol

are trademarks of DTS, Inc. DTS and Play-Fi are registered

here: www.spotify.com/connect/third-party-licenses.

The Bluetooth

®

word mark and logos are registered

trademarks owned by the Bluetooth SIG, Inc. and any use of

such marks by Paradigm Electronics Inc. is under license.

Other trademarks and trade names are those of their

respective owners.

For more information visit paradigm.com

07.18.17

Congratulations! .................................................... 1

Important Safety Instructions ......................................... 2

Important Safety Information .........................................3

What’s In The Box ................................................... 4

Network Requirements ..............................................5

System Requirements ...............................................5

Features & Functions ................................................6

Controls & Connections .............................................. 7

Bluetooth (Pairing & Operation) ....................................... 8

Play Music & Connect Multiple PW Series Products ..................... 9

Anthem Room Correction (ARC

™

) ...................................... 9

Wireless Surround Sound Setup .....................................10

Updates ...........................................................12

Updates Via USB ...................................................12

Device Usage Guide ................................................. 12

Basic Troubleshooting ..............................................13

Technical Specifications .............................................18

Limited Warranty ...................................................19

CONGRATULATIONS!

Thank you for purchasing this Paradigm

®

Premium Wireless

Series product.

Paradigm

®

and its sister company, Anthem

®

have leveraged over 30 years in

groundbreaking loudspeaker and amplifier design to create the Paradigm

®

Premium Wireless Series of wireless speakers and powerful amplifier.

The inclusion of DTS Play-Fi

®

technology to Paradigm’s technology platforms

means you can enjoy high fidelity, lossless music streamed from your Android

™

device, iOS device, tablet or PC — to a premium sounding Paradigm speaker, or

amplifier. Using your home Wi-Fi network, you can stream music to individual

speakers, or play the same music to all Paradigm

®

Premium Wireless Series

devices you have installed — all with crystal clear clarity.

1

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

15. The apparatus shall not be exposed to dripping or splashing and

that objects filled with liquids, such as vases, shall not be placed on

apparatus.

16. Maintain a minimum of 20-30cm distance around the apparatus for

sufficient ventilation.

17. The ventilation should not be impeded by covering the ventilation

openings with items such as newspapers, table-cloths, curtains, etc.

18. No naked flame sources such as lighted candles, should be placed

on the apparatus.

19. Apparatus may be used in tropical climates.

20. This equipment is a Class II or double insulated

electrical appliance.

2

IMPORTANT SAFETY INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE AND OBJECTS FILLED WITH

LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED

ON THIS APPARATUS.

• TO COMPLETELY DISCONNECT THIS APPARATUS

FROM THE AC MAINS, DISCONNECT THE POWER

SUPPLY CORD PLUG FROM THE AC RECEPTACLE.

• THE MAINS PLUG OF THE POWER SUPPLY CORD

SHALL REMAIN READILY ACCESSIBLE.

The lightning bolt flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING! Do not use your Paradigm product(s)

outside of the country of original sale — voltage

requirements vary by country. Improper voltage can

cause damage that will be potentially expensive to

repair. Paradigm products are shipped to authorized

Paradigm distributors with the correct power supply

for use in the country of intended sale. A list of

authorized distributors can be accessed at

www.paradigm.com or by emailing info@paradigm.com.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING!

3

4

2

3 4

1. Paradigm PW 300 Speaker

2. 6’ (1.8 m) Power Cable

3. Owner’s Manual and Setup Guides

4. Rubber Feet (x4)

1

WHAT’S IN THE BOX …

+

–

5

You must have the following to connect your Paradigm product to

your network:

• A high-speed DSL/Cable modem or a fiber-to-the-home

broadband connection for reliable playback of music services

based on the internet. Note: Satellite internet services are

prone to playback issues due to fluctuating download rates.

• If your modem is not a modem/router combination you must

purchase and install a router into your home network before

proceeding.

• If you plan to use the DTS Play-Fi App on an Android or iOS

device or you are setting up a Paradigm product for Wi-Fi

streaming, you will need a wireless router.

• Have your network password ready before connecting the

Paradigm product to your network.

NOTE: To make the quickest connection, use a dual-band router

and connect your Paradigm Product to the 5 GHz network instead

of the 2.4 GHz Network.

NOTE: If your wireless connectivity is weak or not available,

connect your Paradigm product to your router with an ethernet

cable (not included).

TIP! Paradigm Premium Wireless Series products communicate

with wireless networks that support 802.11 g/n wireless

technology. For the fastest streaming performance, a network

that supports 802.11 n wireless technology is recommended. A

network supporting 802.11 b may be used, but it will effectively

stream to only one device equipped with DTS Play-Fi.

TIP! For superior performance connect your PC or NAS (Network-

Attached Storage) drive that holds your personal music library to

your network router using the provided Ethernet cable.

NETWORK REQUIREMENTS

SYSTEM REQUIREMENTS

• An Android device running Android 4.0 or later.

• An iOS device running iOS 8.0 or later.

• Devices running Bluetooth v2.1 or later.

• A Windows

®

PC running Windows

®

7, 8, 8.1, and 10.

FEATURES & FUNCTIONS

Power Button ( ):

• Press

to power on/off.

- If no signal is received for 20

minutes, unit will enter into standby.

- Power & Bluetooth LED will turn off;

Wi-Fi indicator will remain illuminated

(unless connected via Ethernet).

Power Button ( ) (Reboot & Reset):

Reboot:

• Press & hold for 3 sec to clear

currently connected Bluetooth Devices.

- Power button LED will blink once

indicating pairing has been broken.

- Tone will verify a cleared unit.

- Bluetooth indicator will return to

discovery mode.

Reset:

• Press & hold for 10 sec to reset your

PW 300 to factory settings (Reset).

- Note this will clear all current

networks and Bluetooth devices.

- Power button will begin to blink after

10 sec, followed by the Bluetooth and

Wi-Fi Indicator.

- Tone will verify reset is complete.

Volume Up/Down Buttons (

/ ):

• Press

to increase the volume level.

• Press to decrease the volume level.

• Press and hold either

/ to ramp the

volume level up or down.

Wi-Fi Indicator (

):

The Wi-Fi Indicator ( ) tells you what your

PW 300 is doing:

• Fast Blinking — Your PW 300 is booting up.

• Blinking — Your PW 300 is attempting to

connect to a wireless router.

• Slow Pulse — Setup Mode.

• Two Blinks > Pause — WPS Mode.

• Solid White — Connected to router.

• Off — Connected to a router

using a wired connection.

Bluetooth Indicator (

):

The Bluetooth Indicator ( ) tells you

what your Paradigm product is doing:

• Blinking — Discovery Mode.

• Solid Blue — Connected

to Bluetooth Device.

• Solid Green — Connected to

Play-Fi Device (Play-Fi In Use).

• Off — Unit In Standby Mode.

Wi-Fi Setup Button:

Initiates Wi-Fi setup for both Wi-Fi

Protected Setup (WPS) and Standard

Wi-Fi Setup.

• Push & hold for 4 seconds to enter

WPS setup mode.

• Push & hold for 8 seconds to reset

all wireless settings.

• Places your PW 300 into setup mode

(Slow Pulse Wi-Fi Indicator).

6

+

–

7

CONTROLS & CONNECTIONS

Power

Wi-Fi Indicator

Bluetooth Indicator

AC Power

(Mains)

Input

Volume Up

Volume Down

Wi-Fi

Setup

Button

Ethernet

Input

USB

(factory

use only)

+

–

1/4”-20 threaded insert

hole for wall mounting.

The mounting bracket

you choose must support

the weight of the speaker.

Bluetooth Pairing:

• Make sure your PW 300 is plugged in and powered on.

• The Bluetooth LED should be blinking indicating that the device

is in discovery mode.

• Open Bluetooth settings on the desired device.

• From the list provided select PW 300.

• Once paired the PW 300 will emit a tone verifying that it has

been paired and is ready to be used.

• The LED will cease blinking and will now remain solid blue.

Pairing an additional Bluetooth Device:

If the two devices are in the same home/room the original device must

be disconnected or Bluetooth must be disabled.

• Disable Bluetooth on the originally paired device (or simply

disconnect from the PW 300 from the Bluetooth settings on the

original device).

• The Bluetooth LED will return to its blinking state indicating that

the device is in discovery mode.

• Open Bluetooth settings on the desired device.

• From the list provided select PW 300.

• Once paired the PW 300 will emit a tone verifying that it has been

paired and is ready to be used.

• The LED will cease blinking and will now remain solid blue.

Breaking a Bluetooth Pairing:

• Open Bluetooth settings on the desired device.

• From the list provided select PW 300.

• From the device options select Forget this Device — PW 300.

• The LED will now return to its blinking state indicating that the

device is in discovery mode.

Bluetooth Operation:

• Bluetooth LED should be Solid Blue.

• If LED is Solid Green — PW 300 is connected to a Play-Fi device,

disconnect from Play-Fi device prior to using Bluetooth.

• On the desired device open media to be played.

• Select PW 300 from device list (see image below).

• If unit is not on the list — PW 300 is connected to a different device.

• Start music playback.

• Volume adjustments made on device, should be reflected on PW 300.

• Volume adjustments made on

PW 300, should be reflected

on device.

BLUETOOTH (PAIRING & OPERATION)

8

ANTHEM ROOM CORRECTION (ARC

™

)

PLAY MUSIC & CONNECT MULTIPLE PW SERIES PRODUCTS

Once your PW 300 is connected to your home network, you can

start playing music anytime.

1. Activate the DTS Play-Fi App on your mobile device or PC. If

you have setup more than one Paradigm product, select which

one you want to stream music to.

2. Select your music source — personal music library or any

subscription-based music service contained on your mobile

device or PC, Internet Radio, or from select online music

services such as Deezer, Songza, etc. (visit our website at

paradigm.com to view a full list of available music services).

How to Connect Multiple Paradigm Premium Wireless

Series products:

1. To connect additional Paradigm Premium Wireless Series

products to your network, open the DTS Play-Fi App and

select “Setting”.

2. Select, “Add Play-Fi Device”

3. Follow the instructions to add each Paradigm Premium

Wireless Series product.

Primary/Secondary Zones:

When using the DTS Play-Fi App on your device, you will notice

when streaming music to your Paradigm Premium Wireless Series

product that there are two groups: Primary and secondary zones.

The DTS Play-Fi module within your Paradigm Premium Wireless

Series product requires that a primary speaker be selected to

create a new listening session or zone. The purpose of this is to

eliminate any echo, found on other ecosystems, and to maximize

synchronization down to 1 millisecond.

We suggest that you select the Paradigm Premium Wireless Series

product with the strongest signal strength as your primary device.

It should be noted that secondary speakers are connected to your

primary speaker, so if you disable your primary speaker for any

reason, your secondary speaker will be temporarily unavailable

until a primary speaker is selected again.

If you wish to use Anthem Room Correction on the PW 300, it

must be connected to a Paradigm PW Soundbar in a wireless

theater application.The PW Soundbar is the main source for

audio streaming when paired with the PW 300. The PW 300 will

act strictly as a surround speaker and cannot be used as a single

source for music playback for both DTS Play-Fi & Bluetooth.

9

WIRELESS SURROUND SETUP

10

Surround Set-Up will begin and the app will preface with some

information and instructions. Once you proceed, the app will detect

if there are products available on the network that can support

DTS Play-Fi Surround Sound, or if there are products that need an

update from the manufacturer to enable support.

The guided setup will walk you through selecting a speaker to set

the correct placement and distance (this and other settings can be

adjusted later after setup is complete). This process is the same for

all three speaker placements, but the PW Soundbar (Front position

speaker) must be designated as a DTS Play-Fi Surround Sound Master.

NOTE: A Paradigm PW Soundbar and a device with the DTS Play-Fi

app is required in order to complete this setup.

Once the PW Soundbar has been connected to your network,

proceed with the Surround Sound setup in your DTS Play-Fi app.

Start by simply tapping on the Settings icon on the main page of

the DTS Play-Fi app, then navigate to the Surround Sound option.

This will open the Settings page for Surround Sound, and since you

haven’t set up DTS Play-Fi Surround Sound yet, it will prompt you to

do so by tapping on the + button down in the lower right.

NOTE: The PW 300 must be connected to the wireless

network for the Wireless Surround Setup procedure. If your

PW 300 is wired to your network, disconnect the Ethernet cable

and connect it wirelessly to your wireless network.

After you’ve setup every speaker(s) position and distance, the app

will automatically configure your system as needed. Once the

setup is complete after 60 seconds or so, a confimation message

will appear.

11

UPDATES UPDATES VIA USB

DTS Play-Fi App Update:

If the DTS Play-Fi app on your device requires an update, the app

will notify you that an update is available and guide you through

the update process.

Paradigm Firmware Update:

At Paradigm we constantly strive to improve the performance and

functionality of your system, as a result from time to time your

Paradigm Premium Wirless Series product will require firmware

updates. Please regularly check our website at www.paradigm.com

for the latest firmware updates.

1. Get the software file from www.paradigm.com/software and

place on your desktop.

2. Unzip the file and copy firmware “PW 300.hex” into root directory

of USB device.

3. Ensure the PW 300 is disconnected from the wall outlet.

4. Plug the USB device into the rear of the PW 300 where indicated.

5. Press and hold the power button on the PW 300.

6. While holding the power button down, plug the PW 300 into the

electrical outlet. Continue to hold the power button for 2 or 3

seconds more.

7. The power LED will rapidly blink.

8. The update will be complete when the power LED stops blinking.

12

• Select music services

• iTunes — music stored on device

• All audio content

Apple iOS

Play-Fi

•

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

Content

Device

App

Bluetooth

(Single PW 300)

Multi-Room (Play-Fi)

Windows PC

Play-Fi

DEVICE USAGE GUIDE



• Select music services

• Music stored on device

• All audio content

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

Mac OS

Android

–

Play-Fi

•

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

BASIC TROUBLESHOOTING

13

CAUTION: Warning: Do not open your PW 300.

Under no circumstances should your PW 300

be repaired by anyone other than an authorized

Paradigm Dealer, as this will invalidate the

warranty. Please contact Paradigm Customer

Support for more information.

If a problem occurs, you can try the troubleshooting suggestions

listed below. If one of these doesn’t remedy the problem, or

you are not sure how to proceed, please contact the Paradigm

Customer Support team at support@paradigm.com. Alternatively,

visit our website at paradigm.com/support for detailed

troubleshooting solutions.

I am unable to connect

my PW 300 to my Wi-Fi

network.

1. Verify that your Wi-Fi network is functioning.

2. Your router’s Wi-Fi signal may be weak or your PW 300 may be out of range of your router’s Wi-Fi

network. Move the PW 300 closer to the router.

3. Before connecting to your network, verify that your PW 300’s Discovery Mode Wi-Fi Indicator ( )

is pulsing slowly. This indicates the wireless network is ready to pair. A Solid White Wi-Fi Indicator

( ) indicates the PW 300 is paired to a wireless network. If the Bluetooth indicator ( ) is

illuminated BLUE, this indicates the PW 300 is paired to a Bluetooth device; Try disconnect from

the Bluetooth device.

4. Reboot your PW 300 (see page 6).

5. Reset your PW 300 to factory settings (see page 6).

Problem Possible Solutions

14

The DTS Play-Fi App

cannot find my PW 300.

Verify that the following are true:

1. The PW 300 is fully powered on and in Discovery Mode Wi-Fi Indicator (

) is

pulsing slowly).

2. You are within the recommended range of your router.

3. Your device has its Wi-Fi enabled.

4. There are no other apps on your device that are currently running that are impeding wireless

connectivity to your network.

• Restart your phone, tablet or PC (refer to the Owner’s Manual for further details).

• If you still can’t find the PW 300 on your network, and are in an office environment, verify with

your network administrator that no special permissions are enabled that would prevent external

wireless devices from broadcasting within the network.

• If the PW 300 remains unfound, perform a Reboot (Power Cycle) (see page 6) on the offending unit

and redownload the DTS Play-Fi App.

• If the PW 300 remains unfound, perform a Factory Reset (see page 6) on the offending unit and

redownload the DTS Play-Fi App.

Problem Possible Solutions

BASIC TROUBLESHOOTING (cont’d …)

15

The DTS Play-Fi App

says “Play-Fi Devices

Lost.”

If you see this message, it could mean one or more things:

• The connection to your network is very weak.

• There is heavy network traffic.

• You have moved out of your personal network’s coverage range.

• You have lost your network connection.

• You have connected to a network other than the one your PW 300 is on.

• Your device’s wireless streaming has been taken over by another app.

• Your device lost power in the middle of communication.

Make sure the following are true:

• Verify that your network setting and that your devices are connected to the same network.

• Ensure that your device has not left the range of your router.

• Verify that your device is on the same network as your PW 300.

Finally, exit and then restart the DTS Play-Fi App. It should now find your PW 300.

If you are still unable to find the Paradigm PW 300, perform a Reset (see page 6) on the offending

unit and re-download the DTS Play-Fi App.

Problem Possible Solutions

I am unable to pair

my PW 300 to my

Bluetooth device

My Bluetooth device

cannot find the PW 300

• Verify that your PW 300 is powered on — power button should be illuminated, Bluetooth LED

should be blinking (discovery mode).

• Verify that your PW 300 is within range — for pairing purposes unit should be no more than 5’ away.

• Verify that your PW 300 is not connected to another Bluetooth device — bluetooth indicator should

be blinking, Solid LED indicates pairing to another device.

• If the PW 300 remains unfound, Reboot your PW 300 (see page 6).

• If the PW 300 remains unfound, Reset your PW 300 (see page 6).

• Verify that your PW 300 is powered on — power button should be illuminated, Bluetooth LED should be

solid blue (Paired).

• Verify that your PW 300 is within range — maximum range for Bluetooth devices is approx. 30’ (line of sight).

• Verify that your PW 300 is not connected to another Bluetooth device.

• Restart your phone, tablet or PC (refer to the Owner’s Manual for further details).

• If the PW 300 remains unfound, Reboot your PW 300 (see page 6).

• If the PW 300 remains unfound, Reset your PW 300 (see page 6).

Problem Possible Solutions

BASIC TROUBLESHOOTING (cont’d …)

16

My Bluetooth device

has lost connection

to the PW 300

• Verify that your PW 300 is powered on — power button should be illuminated, Bluetooth LED

should be illuminated solid blue (Paired).

• Verify that your PW 300 is within range — maximum range for Bluetooth devices is approx.

30’ (line of sight).

• Verify that your PW 300 is not connected to another device or that Play-Fi has not been opened on

another device — green Bluetooth LED indicates Play-Fi Connection.

• Restart your device.

• If the PW 300 remains unfound, Reboot your PW 300 (see page 6).

• If the PW 300 remains unfound, Reset your PW 300 (see page 6).

Problem Possible Solutions

17

18

Design

High Frequency Driver

Bass/Midrange Driver

Low Frequency Extension

Frequency Response (On Axis)

Frequency Response (30°)

Sensitivity - Room

Sensitivity - Anechoic

Amplification

Wireless Connectivity

Inputs

Dimensions (h x w x d)

Weight

Finish

PW 300 Premium Wireless Speaker

2-Driver, 2 way bookshelf

3/4” (19 mm) polymer dome

4” (102 mm) polypropylene cone

48 Hz

67 Hz to 18 kHz

67 Hz to 17 kHz

82 dB

85 dB

40 W RMS, 80 W peak

2.4 and 5.0 GHz, 802.11 g/n, Bluetooth

USB (for firmware updates), Ethernet 10/100

8-3/16” x 5-11/16” x 5-1/16” (20.8cm x 13.5cm x 12.8cm)

4.5lbs (2.0 kg) each

Black & White

TECHNICAL SPECIFICATIONS

La page charge ...

Paradigm PW 300 Manuel utilisateur

Paradigm PW 300 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents