DeWalt DWMT70775W70781 Manuel utilisateur

Marque: DeWalt

Modèle: DWMT70775W70781

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

DWMT70775

3/8" Impact Wrench

Clé à chocs 9,5 mm (3/8 po)

Llave de impacto de 9,5 mm (3/8”)

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT • www.dewalt.com

English

A. 3/8" Square Drive

B. Tr igger

C. Ergonomic Handle

D. 1/4" Air Inlet

E. Shock Resistant Housing

Bumpers

SPECIFICATIONS

MODEL

DWMT70775

SQUARE DRIVE

3/8"

CLUTCH TYPE

Twin Hammer

MAXIMUM TORQUE (REVERSE)

300 Ft.Lbs (405 Nm)

FREE SPEED (@90PSI)

11000 RPM

BLOWS PER MINUTE

1200 BPM

NET WEIGHT

2.8 LBS (1.3Kg.)

EXHAUST TYPE

Handle

AVERAGE AIR CONSUMPTION

(@ 90 PSI)

33.5 SCFM (16 L/s)

4.8 CFM (2.3 L/s)

AVERAGE AIR CONSUMPTION

(AT LOAD)(@ 90 PSI)

24.7 SCFM (12 L/s)

3.5 CFM (1.7 L/s)

AIR INTLET SIZE

1/4" NPT(F)

RECOMMENDED HOSE SIZE

3/8" (10MM)

MAX. AIR PRESSURE

90 PSI

DWMT70775

3/8" IMPACT WRENCH

F. Composite Body

G. Twin Hammer Mechanism

H. Exhaust

I. Forward/Reverse

Adjustable Power Dial

FIG.1

English

Denitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and pay

attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which,

if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

WALT (1-800-433-9258)

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some example of these chemicals are:

 • Leadfromlead-basedpaints

 • Crystallinesilicafrombricksandcement

and other masonry products

 • Arsenicandchromiumfromchemically-treatedlumber

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, al ways wear OSHA/MSHA/NIOSH approved,

properly fit ting face mask or res pi ra tor when us ing such tools.

When using air tools, basic safety precautions should always be

followed to reduce the risk of personal injury.

WARNING: This product contains chemicals, known to the

State of California to cause cancer, and birth defects or other

reproductive harm. Wash hands after handling.

SAVE THESE INSTRUCTIONS

WARNING:

Improper operation or maintenance of this product

could result in serious injury and property damage.

Read and understand all warnings and operating

instructions before using this equipment. When using

air tools, basic safety precautions should always be

followed to reduce the risk of personal injury.

WARNING:

Read and understand this instruction manual and tool labels

before installing, operating or servicing this tool. Keep these

instructions in a safe accessible place.

Operators and others in work area must wear ANSI Z87.1 CAN/

CSA Z94.3 approved safety glasses with side shields.

Operators and others in work area must wear ear protection.

Oil daily for optimal performance.

English

WARNING:

DO NOT use hand tool sockets. Use impact quality sockets only.

WARNING:

 • Nevertriggerthetoolwhennotappliedtoaworkobject

Attachmentsmustbesecurelyattached.

Looseattachmentscancauseseriousinjury.

 • Protectairlinesfromdamageorpuncture.

 • Neverpointanairtoolatoneselforanyotherperson.

Serious injury could occur.

 • Checkairhosesforweakorwornconditionbeforeeachuse.

Make sure all connections are secure.

 • Keepallnuts,boltsandscrewstightandensureequipmentisin

safe working condition.

 • Donotputhandsnearorundermovingparts.

WARNING:

 • Avoidprolongeduse:repetitivemotionorexposuretovibration

may be harmful to your hands or arms. Use gloves to provide

extra cushion, take frequent rest periods, and limit daily

time of use.

 • DoNotUseoxygenorreactivegases;explosionmayoccur.

 • DoNotExceedairpressureof90PSI.

 • Readallmanualsincludedwiththisproductcarefully.

Be thoroughly familiar with the controls and the proper use

of the equipment.

 • Onlypersonswellacquaintedwiththeserulesofsafeoperation

should be allowed to use the air tool.

 • Donotexceedanypressureratingofanycomponent

in the system.

 • Disconnecttheairtoolfromairsupplybeforechangingtoolsor

attachmentsandduringnon-operation.

 • Alwayswearsafetyglassesandearprotectionduringoperation.

Alwayswearapprovedsafetyglasseswithshields.Alwayswear

approved hearing protection.

 • Donotwearloosefittingclothingorapparelwhichcontains

loose straps or ties, etc. Which could become entangled in

moving parts of the tool and results in serious personal injury.

 • Donotwearjewelry,watches,identifications,bracelets,

necklace, etc. When operating any tool, they may become

caught in moving parts and result in serious injury.

 • Donotdepresstriggerwhenconnectingtheairsupplyhose.

 • Alwaysuseattachmentsdesignedforusewithair

powered impact tools.

 • Donotusedamagedorwornattachments.

English

WARNING: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Abrasivetoolssuchas

sanders and grinders,

rotating tools such as drills,

and impact tools such as

wrenches, hammers,

and reciprocating saws

are capable of generating

sparks which could

result in ignition of

flammable materials.

 • Neveroperatetoolsnear

flammable substances such

as gasoline, naptha,

cleaning solvents, etc.

 • Workinaclean,well

ventilated area free of

combustible materials.

 • Neveruseoxygen,

carbon dioxide or other

bottled gases as a power

source for air tools.

 • Exceedingthemaximum

pressure rating of tools

accessories could cause

an explosion resulting

in serious injury.

 • Usecompressedairregulated

to a maximum pressure at or

below the rated pressure

of any attachments.

WARNING: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Abrasivetools,suchas

grinders, sanders, and

cut-off tools generate dust

and abrasive materials which

can be harmful to human

lungs and respiratory system.

• AlwayswearMSHA/NIOSH

approved, properly fitting face

mask or respirator when

using such tools.

• Somematerialssuchas

adhesives and tar contain

chemicals whose vapors

could cause serious injury

with prolonged exposure.

• Alwaysworkinaclean,dry,

well ventilated area.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Longtermexposuretonoise

produced from the operation

of air tools can lead to

permanent hearing loss.

• AlwayswearANSI (S3.19)

hearing protection.

English

WARNING:

RISK OF INJURY

WHAT CAN HAPPEN HOW TO PREVENT IT

• Toolsleftunattended,orwith

the air hose attached can be

activated by unauthorized

persons leading to their injury

or injury to others.

• Removeairhosewhentool

is not in use and store tool

in a secure location away

from reach of children and/or

untrained users.

• Airtoolscanpropelloose

objects or other materials

throughout the work area.

• Useonlyparts,fasteners,and

accessories recommended by

the manufacturer.

• Keepworkareacleanandfree

of clutter. Keep children and

others away from work area

during operation of the tool.

• Keepworkareawelllit.

• Airtoolscanbecome

activated by accident during

maintenance or tool changes.

• Removeairhosetolubricate,

add, or replace sockets.

• Nevercarrythetool

by the hose.

• Avoidunintentionalstarting.

Don’t carry hooked-up tool with

finger on trigger.

• Repairserviceshouldbedone

only by an authorized service

representative.

• Awrenchorakeythatisleft

attached to a rotating part of

the tool increases the risk of

personal injury.

• Removeadjustingkeysand

wrench before turning

the tool on.

WHAT CAN HAPPEN HOW TO PREVENT IT

• Using inflator nozzles for

duster applications can cause

serious injury.

• DO NOT use inflator nozzles

for duster applications.

• Air tools can cause the work

piece to move upon contact

leading to injury.

• Use clamps or other devices

to prevent movement.

• Lossofcontrolofthetoolcan

lead to injury to self or others

• Never operate tool while

under the influence of

drugs or alcohol.

• Don’t overreach. Keep proper

footing and balance at all times.

• Keep handles dry, clean, and

free from oil and grease.

• Stay alert. Watch what you are

doing. Use common sense.

Do not operate tool when

you are tired.

• Poor quality, improper, or

damaged tools such as

grinding wheels, chisels,

sockets, drill, etc., can fly

apart during operation,

propelling particles

throughout the work area

causing serious injury.

• Always use tool attachments

rated for the speed of

the power tool.

• Never use tools which have

been dropped, impacted or

damaged by use.

• Use only impact grade sockets

on an impact wrench.

• Do not apply excessive force

to the tool – let the tool

perform the work.

English

WARNING:

RISK OF INJURY (CONTINUED)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Improperlymaintainedtool

and accessories can

cause serious injury.

• Maintainthetoolwithcare.

• Thereisariskofburstingif

the tool is damaged.

• Checkformisalignmentor

binding of moving parts,

breakage of parts, and any

other condition that affects the

tool’s operation. If damaged,

have the tool serviced

before using.

• Fastenerscouldricochetor

be propelled causing serious

injury or property damage.

• Neverpointdischargeoftool

at self or others.

• Donotpulltriggerunless

tool contact safety device is

against work surface.

• Neverattempttodrive

fasteners into hard surfaces

such as steel, concrete, or tile.

• Takecaretoavoiddriving

a fastener on top of

another fastener.

• Positiontoolcarefullysothat

fasteners will be delivered to

the proper location.

WARNING:

RISK OF ELETRIC SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thistoolisnotprovidedwith

an insulated gripping surface.

Contact with a “live” wire will

also make exposed metal

parts of the tool “live”

and can result in

electrocution or death.

• Avoidbodycontactwith

grounded surfaces such as

pipes, radiators, ranges, and

refrigerators. There is an

increased risk of electric shock

if your body is grounded.

• Thoroughlyinvestigatethe

workpiece for possible hidden

wring before performing work.

English

WARNING:

RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Airpoweredequipmentand

power tools are capable of

propelling materials such as

metal chips, saw dust, and

other debris at high speed,

which could result in

serious eye injury.

• AlwayswearANSI Z87.1 CAN/

CSA Z94.3 approved safety

glasses with side shields.

• Neverleaveoperatingtool

unattended. Disconnect air

hose when tool is not in use.

• Compressedaircanbe

hazardous. The air stream

can cause injury to soft tissue

areas such as eyes, ears, etc.

Particles or objects

propelled by the stream

can cause injury.

• Foradditionalprotectionuse

an approved face shield in

addition to safety glasses.

• Toolattachmentscanbe

come loose or break and fly

apart propelling particles at

the operator and others

in the work area.

• Makesurethatany

attachments are

securely assembled.

WARNING:

RISK OF CUT OR BURNS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Toolswhichcut,shear,

drill, punch, chisel, etc.,

are capable of causing

serious injury.

 • Keeptheworkingpart

of the tool away from

hands and body.

WARNING:

RISK OF ENTANGLEMENT

WHAT CAN HAPPEN HOW TO PREVENT IT

• Toolswhichcontainmoving

elements, or drive other

moving tools such as grinding

wheels, sockets, sanding

discs,etc., can become

entangled in hair, clothing,

jewelry and other loose

objects, resulting

in severe injury.

• Neverwearloosefitting

clothes, or apparel which

contains loose straps or ties,

etc., which could become

entangled in moving parts

of the tool.

• Removeanyjewelry,watches,

identifications, bracelets,

necklaces, etc., which might

become caught by the tool.

• Keephandsawayfrommoving

parts. Tie up or cover long hair.

• Alwayswearproperfitting

clothing and other safety

equipment when

using this tool.

English

WARNING:

AIR SUPPLY AND CONNECTIONS

• Donotuseoxygen,combustiblegases,orbottledgases

as a power source for this tool as the tool may explode,

possibly causing injury.

• Donotusesupplysourceswhichcanpotentiallyexceed

200PSI(13.8bar)astoolmayburst,possiblycausinginjury.

• Theconnectoronthetoolmustnotholdpressure

when air supply is disconnected. If a wrong fitting is used,

the tool can remain charged with air after disconnecting

and thus will be able to after the air line is disconnected

possibly causing injury.

• Alwaysdisconnectairsupply:

1)Beforemakingadjustments;

2)Whenservicingthetool;

3)Whentoolisnotinuse;

4)Whenmovingtoadifferentworkarea,asaccidental

actuation may occur, possibly causing injury.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

English

FEATURES

ADJUSTABLE POWER DIAL

The dial (I) controls the direc-

tion between forward and reverse

for driving or removing fasteners,

respectively. Point the dial to the

left for reverse, and to the right for

forward. The dial also controls the

three torque speed settings. The

torque increases with larger

circle settings.

SQUARE DRIVE

The 3/8" square drive (A) allows

attachment of sockets with a

3/8" square drive.

TRIGGER

The trigger

(B)

allows the operator to

control the start

and stop of the air tool.

COMPOSITE BODY

The body of the air tool is a

high-impact composite design (F)

for reduced weight and superior

power-to-weight ratio. The composite body reduces fatigue and

provides insulation from cold air passing through the handle.

TWIN HAMMER MECHANISM

This air tool contains a twin hammer mechanism which provides

more durability and a longer tool life.

HANDLE

This air tool has an ergonomic grip (C) made of molded

thermoplastic elastomer (TPE) design for improved comfort,

slippage reduction, and better tool control.

EXHAUST

The exhaust (H) is located at the

base of the handle and allows the

exhaust to be directed away from the

operator and working area.

AIR INLET

The tool’s air inlet (D) located at

the bottom of the handle is used

for connecting an air supply with a

standard 1/4" NPT

American thread.

SHOCK RESISTANT HOUSING

BUMPERS

The shock resistant housing

bumpers (E) provide protection

against housing cracks from

accidental drops of the air tool.

R F

English

INSTALLATION

Air Supply

The recommended hook-up is shown in Figure A. Pneumatic tools

operate on a wide range of air pressures. For maximum efficiency

and longer tool life, the pressure of the air supplied to these

tools MUST not exceed the rated PSI at the tool when the tool is

running. Using a higher than rated pressure will cause faster wear

and drastically shorten the tool’s life. A higher air pressure can also

cause an unsafe condition and explosion.

The inside diameter of the hose should be increased to

compensate for unusually long air hoses (over 25 feet).

Minimum hose diameter should be 3/8" I.D.

and fittings should have 1/4” NPT thread.

The use of air line lubricators and air line

filters is recommended to prevent water

in the line that can damage the tool. Drain

the air tank daily. Clean the air inlet filter

screen on at least a weekly schedule to

remove accumulated dirt or other matter

that can restrict air flow.

The tool’s air inlet used for connecting

an air supply has standard 1/4” NPT

American thread.

Safety Rules For Pneumatic Tools

1) Inspect the air hose for cracks or other problems.

Replace the hose if worn.

2) Never point an air hose at another person.

3) Disconnect the tool when not in use, or before performing

service or changing accessories.

4) Use proper hoses and fittings. Never use quick change

couplings attached to the tool. Instead, add a hose and

coupling between the tool and the air supply.

1/2”(or larger)

Pipe and Fittings

Coupler

Air Hose

Leader Hose

Tool

Nipple

Oiler

Filter

Drain Daily

Figure A

English

PREPARATION FOR USE

Proper Use Of The Tool

Your new 3/8" Drive Impact Wrench is designed for driving, tightening

and loosening threaded fasteners, usually nuts and bolts, when fitted

with a suitable impact socket. Always use impact-rated extension

bars, universal joints and socket adapters between the square

output drive of the impact wrench and the female square drive of the

socket. Do not use the tool for any other purpose than that specified

without consulting the manufacturer or the manufacturer’s authorized

supplier. To do so may be dangerous.

Never use the impact wrench as a hammer to dislodge or

straighten cross threaded fasteners. Never attempt to modify

the tool for other uses.

Work Stations

Your impact wrench should only be used as a hand operated tool.

It is always recommended that the tool is used when standing with

solid footing. It can be used in other positions but before any such

use, the operator must be in a secure position having a firm grip and

footing and be aware that when loosening fasteners the tool can

move quite quickly away from the fastener being undone. An

allowance must always be made for this rearward movement so as

to avoid the possibility of hand/arm/body entrapment.

Putting Into Service

Air Supply

CAUTION:

This air tool requires lubrication BEFORE initial use,

also before and after each additional use.

WARNING:

Use a clean lubricated air supply that will give a

measuredairpressureatthetoolof90psi/6.2barwhenthetool

is running with the trigger fully depressed.

Use recommended hose size. It is recommended that the tool is

connected to the air supply as shown in figure A on page 11. Do

not connect the tool to the air line system without incorporating an

easy to reach and operate air shut off valve. The air supply should

be lubricated. It is strongly recommended that an air filter, regulator,

lubricator (FRL) is used as shown in figure A on page 11 as this

will supply clean, lubricated air at the correct pressure to the tool.

Details of such equipment can be obtained from your supplier. If

such equipment is not used then the tool should be lubricated by

shutting off the air supply to the tool and then depressurizing

the line by pressing the trigger on the tool. Disconnect the air

line and pour into the air inlet 1 teaspoon (5cc.) of a suitable

pneumatic motor lubricating oil, preferably incorporating

a rust inhibitor. Reconnect tool to air supply and run tool slowly for a

few seconds to allow air to circulate the oil.

Lubricate tool daily if used frequently, or when it starts to slow or

lose power.

Using An Impact Wrench

WARNING:

1) Read all instructions before using this tool. All operators must

be fully trained in its use and aware of these safety rules.

2) Do not exceed the maximum working air pressure of

90 psi/6.2 bar.

3) Use personal safety equipment.

4) Use only compressed air at the recommended conditions.

5) If the tool appears to malfunction, remove from use immediately

and arrange for service and repair.

6) If the tool is used with a balancer or other support device, ensure

that it is fixed securely.

7) Always keep hands away from the working attachment fitted

to the tool.

8) The tool is not electrically insulated. Never use the tool if there

is any chance of it coming into contact with live electricity.

9) When using the tool, always adopt a firm footing and/or position

and grip the tool firmly to counteract any forces or reaction

forces that may be generated while using the tool.

English

Using an Impact Wrench Continued

10) Use only genuine Dewalt spare parts or parts which perform

equivalently. Do not make temporary or permanent repairs with

unauthorized parts.

11) Do not lock, tape, wire, etc., the on/off trigger in the run position.

The trigger must always be free to return to the “off” position

when it is released.

12) Always shut off the air supply to the tool and depress the trigger

to release air from the feed hose before fitting, adjusting or

removing the working attachment.

13) Check hoses and fittings regularly for wear. Replace if

necessary. Do not carry the tool by its hose. Ensure the hand is

removed from the on/off trigger when carrying the tool with the

air supply connected.

14) Take care against entanglement of moving tool parts with

clothing, ties, hair, cleaning rags, etc. This will cause the body to

be drawn towards the tool and can be very dangerous.

15) Safe working practices and observe all relevant legal

requirements when installing, using or maintaining the tool.

16) Only install the tool when an easily accessible and easily

operable on/off switch is incorporated in the air supply.

17) Take care that the tool exhaust air does not cause problems or

blow onto another person.

18) Never lay a tool down unless the working attachment has

stopped moving.

19) Always ensure that the forward/reverse switch is in the desired

position before starting the tool.

20) Do not use sockets with excessive wear to the input or output

drives. Periodically check the square drive on the impact wrench.

Make surer the socket, extension bar, or other attachment is

securely fitted before operating tool.

21) When loosening fasteners first ensure that there is sufficient

clearance behind the tool to avoid hand entrapment. The tool will

move away from the threaded joint as the nut/bolt is loosened

and rides up the thread, moving the tool with it.

PRE-START CHECKLIST

•Drainwaterfromaircompressortankandcondensationfrom

air lines. (Please refer to air compressor’s operation manual.)

•Lubricatethetool.(Pleaserefertothe“Maintenance”section

in the manual.)

•Selectthenecessaryimpactsockets.Thesocketshaveto

match with the size of the drive on the air impact wrench.

•Connectairimpactwrenchtoairsourcewith

the hose of recommended size.

WARNING: Risk of unsafe operation. Firmly grasp air hose

with hand when installing or disconnenting to prevent hose whip.

WARNING: Risk of bursting. Too much air pressure causes

a hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator output

pressure must never exceed the maximum pressure rating.

OPERATING PROCEDURES

START-UP (FIG. 1, PG. 2)

•Turnontheaircompressorandallowtheairtanktobefilled.

•Settheaircompressorregulatorto90PSI.Thisair

tool operates at a maximum of 90 PSI air pressure.

•Adjustpowerdial(ifitisavailable)todesiredtorque.

•Adjusttooleitherinforwardorreverseposition.Turnthedialallthe

way to the left for reverse direction or right for forward direction.

•Depressthetriggertostartoperatingthetool.

SHUT-DOWN (FIG. 1, PG. 2)

•Releasethetriggerinordertostopthetool.

•Whenchangingsockets,alwaysdisconnectairsupplyto

avoid injury.

•Whenjobiscompleted,turnofftheaircompressorandstore

the air tool after lubrication.

English

OPERATING INSTRUCTIONS

• Securely fit the socket or attachment to the impact wrench.

• Ensure that the forward/reverse switch is in the correct position

for tightening or loosening the fastener.

• The nut/bolt can then run down the thread using the power

drive of the tool. For loosening a joint the tool can be used

in the reverse sequence.

MAINTENANCE

Lubrication

Air tools require lubrication throughout the lifetime of the tools.

The air motor and bearing uses compressed air to power the tool.

The compressed air contains moisture that will rust the air motor

and other parts in side of the tools, therefore lubrication is required

daily. Failure to lubricate the air tool properly will dramatically

shorten the life of the tool and will void the warranty

CAUTION: This air tool requires lubrication BEFORE initial use,

also before and after each additional use.

To Lubricate The Air Tool Manually:

1. Remove any attachment on the drive of air tools, such as:

sockets, chisels and etc.

2. Disconnect the tool from the air supply source, place

the air inlet face up.

3. Depress the trigger and place about 1 teaspoon

(5cc.) of air tool oil into the air inlet. (Depressing the trigger

will help circulate oil in the motor.)

NOTE: Use SAE #10 weight oil if air tool oil is not available.

4. Connect the tool to an air source, cover the exhaust end

with a towel and run for about 20 to 30 seconds.

WARNING: Keep out of the reach of children. If taken internally, do

not induce vomiting, call a doctor immediately.

WARNING: Anyexcessoilinthemotorisimmediatelyexpelled

fromtheexhaustport.Alwaysdirectexhaustportawayfrompeople

or objects.

Storage:

The air tool must be lubricated before storing.

Follow the “Lubrication” instruction with exception of step 4.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number _________________________________________

Date and Place of Purchase ______________________________

FULL THREE YEARS WARRANTY

DeWALT heavy duty industrial tools are warranted for 3 years from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

Latin America: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

WALT

for a free replacement.

Français

LAS CAÍDAS PUEDEN CAUSAR

LESIONES GRAVES. NO PISAR NI

PARARSE EN ESTA ÁREA.

ADVERTENCIA

LES CHUTES PEUVENT CAUSER DE GRAVES

BLESSURES. NE MARCHEZ PAS ET NE VOUS

TENEZ PAS SUR CET EMPLACEMENT.

AVERTISSEMENT

FALLS CAN CAUSE SERIOUS

INJURIES. DO NOT STEP OR STAND

ON THIS AREA.

WARNING

SEE OWNER’S MANUAL FOR

BREAK-IN PROCEDURES.

CAUTION

PARA EL PROCEDIMIENTO DE

ASENTADO DE LA MAQUINA, VER

MANUAL DEL OPERARIO.

ATENCIÓN

CONSULTEZ LE MANUEL DE

L’UTILISATEUR POUR LES

PROCEDURES DE RODAGE.

ATTENTION

ADVERTENCIA

EL USO INDEBIDO PUEDE GENERAR RIESGOS. SEGUIR ESTAS INSTRUCCIONES: RIESGO DE ESTALLIDO. ASEGÚRESE QUE LA VÁLVULA DE SALIDA DEL

COMPRESOR ESTE REGULADA POR DEBAJO DEL MÁXIMO DE LA PRESIÓN DE OPERACIÓN DE LA PISTOLA ROCIADORA O HERRAMIENTA. ANTES DE ARRANCAR

EL COMPRESOR, TIRAR DEL ANILLO EN LA VÁLBULA DE SEGURIDAD PARA ASEGURARSE QUE LA VÁLVULA SE MUEVE LIBREMENTE. DRENAR EL AGUA DEL TANQUE DESPUÉS DE CADA USO.

RIESGO DE FUEGO O EXPLOSIÓN. NO ROCIAR LÍQUIDO NI PINTURAS INFLAMABLES O COMBUSTIBLES CERCA DE CHISPAS, LLAMAS, LLAMAS DE PILOTO O EN ÁREAS CERRADAS. EL ÂREA DE

TRABAJO DEBE ESTAR BIEN VENTILADA. MANTENER EL COMPRESOR ALEJADO POR LO MENOS 20 PIES DEL AREA DE PINTURA. NO LLEVAR NI OPERAR EL COMPRESOR NI DISPOSITIVO ELÉCTRICO

ALGUNO CERCA DEL AREA DEL ROCIADO. NUNCA FUME EN EL ÁREA DEL ROCIADO. USAR UNA MANGUERE DE UN MÍNIMO DE 25 PIES PARA CONECTAR LA PISTOLA AL COMPRESOR. RIESGO DE

DAÑOS PERSONALES. USAR GAFAS DE SEGURIDAD ANSI Z87. NUNCA APUNTAR EL CHORRO DE AIRE COMPRIMIDO O DE MATERIAL QUE SE ESTÉ ROCIANDO A SÍ MISMO NI A OTRAS PERSONAS.

NE RESPIRAR EL AIRE COMPRIMIDO. REDUCIR LA PRESIÓN A CERO ANTES DE DESMONTAR LA MANGUERA. RIESGO DE CHOQUE ELÉCTRICO. ALTO VOLTAJE. DESCONECTAR LA UNIDAD ANTES DE

QUITAR LA CUBIERTA. NO EXPONER A LLUVIA. ALMACENAR EN INTERIORES. PARA SEGURIDAD COMPLETA, OPERACIÓN E INSTRUCCIONES PARA REPARAR, LEER EL MANUAL DEL OPERADOR.

AVERTISSEMENT

UNE UTILISATION INCORRECTE PEUT ÊTRE DANGEREUSE. SUIVEZ LES INSTRUCTIONS CI-DESSOUS: RISQUE D'ECLATEMENT. ASSUREZ-VOUS QUE LA

PRESSION DE SORTIE DU COMPRESSEUR EST RÉGLÉE À UN NIVEAU INFÉRIEUR À LA PRESSION D'UTILISATION MAXIMUM DU PISTOLET VAPORISATEUR OU DE

L'ACCESSOIRE. AVANT DE DÉMARRER LE COMPRESSEUR, TIREZ SUR L'ANNEAU DE LA SOUPAPE DE SÛRETÉ POUR VOUS ASSURER QU'ELLE FONCTIONNE LIBREMENT. VIDANGEZ L'EAU DU RÉSERVOIR

À AIR APRÈS CHAQUE UTILISATION. RISQUE D'INCENDIE OU D'EXPLOSION. NE PAS VAPORISER UN LIQUIDE OU UN PEINTURE INFLAMMABLE OU COMBUSTIBLE PRÈS D'ÉTINCELLES, DE FLAMMES, DE

VEILLEUSES NI DANS UN ENDROIT RESTREINT OU RENFERMÉ. L'AIRE DE VAPORISATION DOIT ÊTRE BIEN AÉRÉE. GARDEZ LE COMPRESSEUR À UNE DISTANCE D'AU MOINS 20 PIEDS DE LA SURFACE À

VAPORISER. NE PORTEZ PAS LE COMPRESSEUR ET NE L'UTILISEZ PAS NI AUCUN AUTRE APPAREIL ÉLECTRIQUE À PROXIMITÉ DE L'AIRE DE VAPORISATION. NE FUMEZ JAMAIS QUAND VOUS

VAPORISEZ. UTILISEZ UN FLEXIBLE D'AIR D'UNE LONGUEUR MINIMUM DE 25 PIEDS POUR RELIER LE PISTOLET VAPORISATEUR AU COMPRESSEUR. RISQUE DE BLESSURES CORPORELLES. PORTEZ DES

LUNETTES DE PROTECTION ANSI Z87. NE DIRIGEZ JAMAIS L'AIR COMPRIME OU DES MATÉRIAUX VERS SOI OU VERS AUTRUI. NE JAMAIS UTILISER DE L'AIR COMPRIMÉ POUR LA RESPIRATION. RÉGLEZ

LA PRESSION À ZÉRO AVANT DE RETIRER LE BOYAU. RISQUE DE CHOC ÉLECTRIQUE. VOLTAGE DANGEREUX. DEBRANCHEZ LA MACHINE AVANT D'ENLEVER BOITIER. N'EXPOSEZ PAS LE COMPRESSEUR

À LA PLUIE. REMISEZ-LE À L'INTÉRIEUR. LISEZ LE MANUEL DE L'UTILISATEUR POUR DES INSTRUCTIONS COMPLÈTES CONCERNANT LA SÉCURITÉ, L'UTILISATION ET LES RÉPARATIONS.

INCORRECT USE CAN CAUSE HAZARDS. FOLLOW THESE INSTRUCTIONS: RISK OF BURSTING. MAKE SURE THE COMPRESSOR OUTLET PRESSURE IS SET

LOWER THAN THE MAXIMUM OPERATING PRESSURE OF THE SPRAY GUN OR TOOL. BEFORE STARTING THE COMPRESSOR, PULL THE RING ON THE SAFETY

VALVE TO MAKE SURE THE VALVE MOVES FREELY. DRAIN WATER FROM TANK AFTER EACH USE. RISK OF FIRE OR EXPLOSION. DO NOT SPRAY A FLAMMABLE OR COMBUSTIBLE

LIQUID OR PAINT NEAR SPARKS, FLAMES, PILOT LIGHTS, OR IN A CONFINED AREA. THE SPRAY AREA MUST BE WELL VENTILATED. KEEP COMPRESSOR AT LEAST 20 FEET AWAY FROM

SPRAY AREA. DO NOT CARRY AND OPERATE THE COMPRESSOR, OR ANY OTHER ELECTRICAL DEVICE NEAR THE SPRAY AREA. NEVER SMOKE WHEN SPRAYING. USE A MINIMUM OF

25 FEET OF HOSE TO CONNECT A SPRAY GUN TO THE COMPRESSOR. RISK OF PERSONAL INJURY. WEAR ANSI Z87 SAFETY GLASSES. NEVER SPRAY COMPRESSED AIR OR MATERIAL

AT SELF OR OTHERS. DO NOT USE COMPRESSED AIR FOR BREATHING. REGULATE PRESSURE TO ZERO BEFORE REMOVING HOSE. RISK OF ELECTRICAL SHOCK. HAZARDOUS VOLTAGE.

UNPLUG UNIT BEFORE REMOVING COVER. DO NOT EXPOSE TO RAIN, STORE INDOORS. READ OWNER'S MANUAL FOR COMPLETE SAFETY, OPERATION, AND REPAIR INSTRUCTIONS.

WARNING

HOLD HOSE FIRMLY TO

PREVENT HOSE WHIP.

CAUTION

SOSTENGA LA MANGUERA

CON FIRMEZA PARA EVITAR EL.

ATENCIÓN

BIEN TENIR LE TUYAU POUR

ÉVITER UN À-COUP.

ATTENTION

DRAIN TANK DAILY OR AFTER EACH USE. CONDENSATION BUILD-UP MAY CAUSE CORROSION

INSIDE TANK RESULTING IN TANK FAILURE. SEE MANUAL FOR INSPECTION PROCEDURES. TO DRAIN

TANK OPEN VALVE SLOWLY AND TILT COMPRESSOR TO EMPTY ACCUMULATED WATER.

WARNING

DRENE EL TANQUE A DIARIO O DESPUÉS DE CADA USO. LA ACUMULACIÓN DE CONDENSACIÓN

PUEDE OCASIONAR CORROSIÓN DENTRO DEL TANQUE Y PROVOCAR FALLA DEL TANQUE.

CONSULTE EL MANUAL PARA CONOCER LOS PROCEDIMIENTOS DE INSPECCIÓN. PARA DRENAR EL TANQUE, ABRA LA

VÁLVULA LENTAMENTE E INCLINE EL COMPRESOR PARAELIMINAR EL AGUA ACUMULADA.

ADVERTENCIA

RÉSERVOIR DE VIDANGE QUOTIDIEN

OU APRÈS CHAQUE UTILISATION. L'HABILLAGE

CONDENSATION PEUT CAUSER LA CORROSION À L'INTÉRIEUR DU RÉSERVOIR AYANT POUR

RÉSULTAT L'ÉCHEC DE RÉSERVOIR. VOIR LE MANUEL POUR DES PROCÉDURES D'INSPECTION. À LA VALVE

OUVERTE

DE RÉSERVOIR DE VIDANGE LENTEMENT ET AU COMPRESSEUR D'INCLINAISON À L'EAU ACCUMULÉE VIDE.

AVERTISSEMENT

GLOSSARY

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute;

a unit of measure of air delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

Code Certification: Products that bear one or more of the

following marks: UL, CUL, ETL, CETL, have been evaluated by

OSHA certified independent safety laboratories and meet the

applicable Underwriters Laboratories Standards for Safety.

RPM: Revolutions per minute; is a measure of the frequency

of a rotation

BPM: Beats per minute.

NPT: National pipe thread (tapered thread); is a U.S. standard

for tapered threads used on threaded pipes and fittings.

ID: Inner diameter

Français

DWMT70775

CLÉ À CHOCS 9,5 MM (3/8 PO)

A. Carré conducteur 12,7 mm

(3/8 po)

B. Gâchette

C. Poignée ergonomique

D. Entrée d’air 6,4 mm (1/4 po)

E. Coussinets antichoc pour

boîtier

F. Corps en composite

G. Mécanisme à double marteau

H. Échappement

I. Cadran de puissance réglable

Avant/arrière

FICHE TECHNIQUE

MODÈLE

DWMT70775

CARRÉ CONDUCTEUR

3/8"

TYPE D'EMBRAYAGE

Double percussion

COUPLE MAXIMAL (INVERSION)

405 Nm (300 pi-lb)

VITESSE À VIDE (À 620 KPA (90 PSI}

11 000 tr/min

COUPS PAR MINUTE

1200 CPM

POIDS NET

1,3 kg (2,8 lb)

TYPE D'ÉCHAPPEMENT

Poignée

CONSOMMATION MOYENNE D’AIR

(À 620 KPA (90 PSI}

16 l/s (33,5 pieds cubes

standard par minute)

2,3 l/s (4,5 pieds cubes

standard par minute)

CONSOMMATION MOYENNE D’AIR

EN CHARGE

(À 620 KPA (90 PSI}

12 l/s (24,7 pieds cubes

standard par minute)

1,7 l/s (3,5 pieds cubes

standard par minute)

DIMENSION DE L’ENTRÉE D’AIR

Filetage conique (F) 6,35

mm (1/4 po)

FIG.1

DIMENSION DE L'ENTRÉE D'AIR

Filetage conique (F) 6,35

mm (1/4 po)

DIMENSION RECOMMANDÉE DU

TUYAU

10 mm (3/8 po)

PRESSION D'AIR MAXIMALE

90 PSI

Français

Dénitions : lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de gravité pour

chaque symbole. Veuillez lire le mode d’emploi et porter une

attention particulière à ces symboles.

DANGER : Indique une situation dangereuse imminente qui, si

elle n’est pas évitée, causera la mort ou des blessures graves.

AVERTISSEMENT :

Indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait se solder par un

décès ou des blessures graves.

ATTENTION : Indique une situation potentiellement dangereuse

qui, si elle n’est pas évitée pourrait se solder par des blessures

mineures ou modérées.

ATTENTION : Utilisé sans le symbole d’alerte à la sécurité,

indique une situation potentiellement dangereuse qui, si elle n'est

pas évitée pourrait se solder par des dommages à la propriété.

POUR TOUTES QUESTIONS OU COMMENTAIRES

RELATIFS(VES) À L’OUTIL OU À PROPOS DE TOUT AUTRE

OUTIL D

WALT, COMPOSER SANS FRAIS LE : 1-800-4-D

eWALT

(1-800-433-9258)

DIRECTIVES DE SÉCURITÉ

IMPORTANTES

AVERTISSEMENT : Nertaines poussières produites par les travaux

de ponçage, sciage, meulage, perçage et autres peuvent contenir des

produits chimiques pouvant selon l’état de Californie causer le cancer,

des anomalies congénitales ou d’autres problèmes liés aux fonctions

reproductrices. Voici quelques exemples de ces produits chimiques :

 • leplombcontenudanslespeinturesàbasedeplomb;

 • lasilicecristallineprovenantdelabrique,ducimentetd’autres

produitsdemaçonnerie;

 • l’arsenicetchromeprovenantdeboistraitéchimiquement.

Lesrisquesreliésàl’expositionàcespoussièresvarientselonla

fréquence à laquelle l’utilisateur travaille avec ce type de matériaux.

Pourréduirevotreexpositionàcesproduitschimiques:travailler

dans un endroit bien ventilé et porter un équipement de sécurité

approuvé par l’OSHA/MSHA/NIOSHcommeunmasqueanti-

poussières spécialement adapté ou un respirateur lors de l’utilisation

de ces outils.

Lorsdel’utilisationd’outilspneumatiques,desprécautionsdebase

en matière de sécurité doivent être suivies afin de réduire le risque

de blessure personnelle.

AVERTISSEMENT : ce produit contient des produits chimiques,

notamment le plomb, reconnus par l’État de Californie comme étant

cancérigènes et pouvant entraîner des anomalies congénitales et

d’autres dangers relatifs à la reproduction. Se laver les mains après

toute manipulation.

CONSERVER CES INSTRUCTIONS

AVERTISSEMENT :

a mauvaise utilisation ou maintenance de ce produit peut

causerdesblessuresgravesEtdesdommagessérieuxaux

biens. Il faut lire et comprendre tous les avertissements et la

Notice d’emploi avant d’utiliser cet équipement. Lorsque

vous utilisez des outils pneumatiques, il faut respecter les

mesures de sécurité fondamentales pour réduire leRisque

de blessures.

Français

AVERTISSEMENT :

l faut lire et comprendre ce guide d’instructions et les

étiquettes de l’outil avant d’installer, d’utiliser cet outil ou d’en

faire l’entretien.

Gardez ces instructions dans un lieu sûr à portée de la main.

oivent porter des lunettes de sécurité avec écrans latéraux

approuvées ANSI Z87.1 CAN/CSA Z94.3.

Lesutilisateursetlesgensdanslazonedetravaildoivent

porter une protection auditive.

Graissez tous les jours pour un rendement optimal.

AVERTISSEMENT :

•Évitezl’utilisationprolongée:lemouvementrépétitifou

l’exposition aux vibrations peuvent être nocifs pour vos mains ou

vos bras. Utiliser des gants pour offrir un maximum de protection,

prendre des pauses fréquentes et limiter le temps d’utilisation

quotidien.

•N’utilisezpasdegazoxygèneouréactif;uneexplosionpeut

survenir.

•Nepasexcéderunepressiond’airde90psi.

•Ilfautlireattentivementtousleslivretsinclusavecceproduit.

Il faut bien se familiariser avec les commandes et l’emploi correct

de l’équipement.

•Seuleslespersonnesquiconnaissentbiencesrèglesde

sécurité devraient utiliser l’outil pneumatique.

•Ilnefautpasexcéderlapressionlimitedescomposantesdu

système.

•Débrancherl’outilpneumatiquedel’arrivéed’airavantdechanger

les outils ou les accessoires et lorsqu’il n’est pas utilisé.

•Ilfauttoujoursporterdeslunettesdeprotectionetune

protection auditive durant l’emploi.Il faut toujours porter des

lunettes de protection avec écrans latéraux.Il faut toujours porter

une protection auditive.

•Ilnefautjamaisporterdesvêtementsamplesouunhabillement

comportant des attaches ou bretelles lâches, etc. qui pourraient

être happées par les pièces mobiles de l’outil et causer des

blessures graves.

•Ilnefautpasporterdebijou,montre,identification,bracelet,

collier, etc. lorsque vous utilisez l’outil, car ils pourraient être

happés par les pièces mobiles de l’outil et causer des

blessures graves.

•Ilnefautpasabaisserlagâchettelorsquevousraccordezl’outil

au boyau d’air d’arrivée.

•Toujoursutiliserunaccessoireconçupourlesoutilspercuteurs

pneumatique.

•Ilnefautjamaisutiliserdesaccessoiresendommagésouusés.

AVERTISSEMENT :

IL NE FAUT JAMAIS utiliser les douilles des outils à main.

AVERTISSEMENT :

•Ilnefautjamaisdéclencherl’outillorsqu’iln’estpasappliqué

contreunobjet.Lesaccessoiresdoiventêtrebienancrés.

Lesaccessoireslâchespeuventcauserdesblessuresgraves.

•Protégezlesconduitsd’airdesdommagesetdesperforations.

•Ilnefautjamaispointerl’outilpneumatiqueverssoiou

autrui. Des blessures graves peuvent survenir.

•Vérifiezlesboyauxd’airencasd’usureoudedétérioration

avant chaque emploi. S’assurer que tous les raccords sont

bien branchés.

•S’assurerquelesboulons,écrousetvissontbienserréset

que l’équipement est en bon état.

•Nejamaisplacersesmainsprèsd’unepiècemobileouendessous.

Français

AVERTISSEMENT :

RISQUE D’EXPLOSION OU D’INCENDIE

Ce qui peut se produire Comment l’Éviter

 • Lesoutilsabrasifscomme

les sableuses et les meules,

les outils rotatifs comme

les perceuses et les outils à

choc comme les clés, les

marteaux et les scies à

action réciproque peuvent

produire des étincelles

qui pourraient allumer des

produits inflammables.

 • Nejamaisutiliserlesoutils

près des substances

inflammables, comme

l’essence, le naphte, les

solvants de dégraissage, etc.

 • Travaillerdansunezone

de travail bien ventilée et

propre, exempte de matériaux

combustibles.

• Nejamaisutiliserdegaz

oxygène, de dioxyde de

carbone ou autres gaz

en bouteille comme source

d’énergie pour les outils

pneumatiques.

• Excéderlapression

limite des outils ou des

accessoires pourrait

provoquer une explosion et

causer des blessures graves.

• Utiliserdel’aircompriméréglé

à une pression maximale près

ou au-dessous de la pression

nominale des accessoires.

DANGER :

RISQUE REPIRATOIRE (ASPHYXIE)

CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER

• Lesoutilsabrasifscomme

les sableuses et les meules

et les outils à tronçonner

produisent de la poussière

et de matériaux abrasifs qui

peuvent être nocifs pour

les poumons et le

système respiratoire.

• Toujoursporterunmasque

facial bien ajusté ou un

respirateur homologué

MSHA/NIOSH lorsque

vous utilisez ces outils.

• Certainsmatériaux,comme

les adhésifs et le goudron,

contiennent des produits

chimiques qui peuvent causer

des blessures graves à

l’exposition prolongée.

• Toujourstravaillerdans

une zone de travail bien

ventilée et propre.

ATTENTION :

RISQUE DE PERTED’OUÏE

QUE FAIRE COMMENT PRÉVENIR

 • Uneexpositionprolongée

au bruit produit par le

fonctionnement des

outils pneumatiques peut

causer une perte auditive

permanente.

 • Toujoursporteruneprotection

auditive ANSI (S3.19).

Français

AVERTISSEMENT : RISQUE DE PERTED’OUÏE

QUE FAIRE COMMENT PRÉVENIR

• Lesoutilslaisséssans

surveillance ou dont le boyau

d’air est branché peuvent être

activés par des personnes

non autorisées qui peuvent se

blesser ou blesser autrui.

• Retirerletuyaud’airlorsque

l’outil n’est pas utilisé et ranger

l’outil dans un endroit sûr hors

de portée des enfants et des

utilisateurs n’ayant pas reçu la

formation requise.

• Lesoutilspneumatiques

peuvent projeter les objets

non fixés et autres matériaux

dans toutes les directions de

la zone de travail.

• Utiliseruniquementlespièces,

les fixations et les accessoires

recommandés par le fabricant.

• Conserverlazonedetravail

propre et en bon ordre. Éloigner

les enfants et autrui de la zone

de travail durant l’utilisation de

l’outil.

• Conserverleslieuxbien

illuminés.

• Lesoutilspneumatiques

peuvent être actionnés

accidentellement lors d’un

entretien ou d’un changement

d’outil.

• Retirerletuyaud’airpour

lubrifier, ajouter ou remplacer

des douilles.

• Nejamaistransporterl’outilpar

le boyau.

• Évitezlesdémarragesnon

intentionnels. Ne transportez pas

l’outil branché avec le doigt sur

la gâchette.

• Lesréparationsdoiventêtre

effectuées seulement par un

représentant de service autorisé.

• Lefaitdelaisserunecléde

réglage ou une clé fixée sur

une pièce tournante augmente

le risque de blessures.

• Retirertouteslesclésde

réglage et les clés avant de

mettre l’outil en marche.

QUE FAIRE COMMENT PRÉVENIR

• Utiliserdesbusesgonflantes

pour l’époussetage peut

causer des blessures graves.

• NE PAS utiliser de buses

gonflantes pour l’époussetage.

• Lesoutilsélectriquespeuvent

provoquer le déplacement de

la pièce de travail au contact

et causer des blessures.

• Utiliserdespincesouautres

dispositifs pour empêcher le

mouvement.

•Lapertedecontrôledel’outil

peut causer des blessures à

soi-même et à autrui.

• Nejamaisutiliserl’outilsous

l’influence d’alcool ou de

drogues.

• Ilnefautpastendrel’outiltrop

loin. Gardez l’équilibre en tout

temps.

• Gardezlesmainspropres,

sèches et exemptes de graisse

et d’huile.

• Restezalerte.Portezattentionà

ce que vous faites. Servez-vous

de votre bon sens. Il ne faut pas

utiliser l’outil lorsque vous êtes

fatigué.

• Desoutilsdemauvaisequa-

lité, inappropriés ou endom-

magés tels que les meules,

les ciseaux, les douilles, les

perceuses, etc., peuvent

voler en morceaux lors du

fonctionnement, projetant des

particules dans toutes les

directions de la zone de travail

et causer des

blessures graves.

• Toujoursutiliserlesaccessoires

cotés pour la vitesse de l’outil

électrique.

• Nejamaisutiliserdesoutilsque

vous avez échappés, impactés

ou endommagés par l’usage.

• Utiliseruniquementdesdouilles

pour clés à chocs avec la clé à

chocs.

• Nepasexercerdeforce

excessive sur l’outil – laisser

l’outil effectuer le travail.

La page charge ...

DeWalt DWMT70775W70781 Manuel utilisateur

Marque: DeWalt

Modèle: DWMT70775W70781

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DWMT70775W70781 User manual
español: DeWalt DWMT70775W70781 Manual de usuario

DeWalt DWMT70775W70781 Manuel utilisateur

Ce manuel convient également à

DeWalt DWMT70775W70781 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents