Rheem TWPH-8550EHT10 Le manuel du propriétaire

Effective: 08-06-2023

Replaces: 07-28-2023

P/N: 100-10000496 Rev. 02

Heat Pump Pool

& Spa Heater

Models: TWPH 4550, 5550, 6550,

6550EHC, 8550, & 8550EHC

FOR YOUR SAFETY: Do not store or use gasoline or other ammable vapors and

liquids or other combustible materials in the vicinity of this or any other appliance.

To do so may result in an explosion or re.

NOTE: The instructions in this manual are for the use of qualied individuals specially trained

and experienced in the installation and maintenance of this type of equipment and related system

components. Installation and service personnel are required by some states to be licensed. Persons

not qualied shall not attempt to install, service, or maintain this equipment.

This manual should be maintained in legible condition and kept adjacent to the heat pump pool heater or in a

safe place for future use.

INSTALLATION AND

OPERATION MANUAL

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

2

QUICK START GUIDE

CLEARANCES

Installation Considerations Page 6.

Installation Clearances Page 7.

Hurricane Tie Down Instructions Page 8.

PIPING

Water Connections Page 9.

Flow Rate & Pressure Drop Page 9.

Freeze Protection Page 34.

Plumbing Diagrams Page 38.

WATER CHEMISTRY

Water Chemistry Page 6.

Table A. Water Chemistry Page 6.

POWER

Electrical Connections Page 10.

Table C. Typical System Electrical Power

Requirements Page 10.

CONTROLS INTERFACE

Wiring Diagram -

208V/230V Single-Phase Page 11.

Heater Control Display Page 12.

Program Menu Page 17.

Digital Controls Operation Page 27.

Remote Mode Selector Page 31.

Connect to Wi-Fi with Raymote Page 43.

External Control Outputs Page 71.

Revision 02 reects the following changes:

Figure 4: Changed Tie Down Clip dimension from "10.000" to 8.00" - 10.00". Removed Steps 5 through 13 and Figure 62 in the "Service

Access to Heater" Section.

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

3

TABLE OF CONTENTS

1. WARNINGS ............................................................. 4

Pay Attention to these Terms ..................................4

2. INTRODUCTION ...................................................... 5

3. WATER CHEMISTRY ............................................... 6

4. INSTALLATION CONSIDERATIONS ...................... 6

5. WATER CONNECTIONS ......................................... 9

6. FLOW RATE & PRESSURE DROP......................... 9

7. ELECTRICAL CONNECTIONS ............................... 9

8. WIRING DIAGRAM ................................................ 11

9. HEATER CONTROL DISPLAY .............................. 12

10. OPERATION MODES ............................................ 12

11. SERVICE MENU ..................................................... 14

Operations and Service Menu...............................16

12. PROGRAM MENU ................................................. 21

Program Menu Diagram ........................................20

13. INSTALLER MENU ................................................ 21

Installer Menu Diagram ......................................... 24

14. SCHEDULE MENU ................................................ 25

Schedule Menu Diagram.......................................26

15. DIGITAL CONTROLS OPERATION ...................... 27

Sequence of Operation .........................................27

System Start-Up ....................................................27

Operational Status Messages ...............................28

Error Messages .....................................................29

16. REMOTE MODE SELECTOR ................................ 31

17. SEASONAL START-UP OR

ANNUAL CHECK ................................................... 34

18. SUMMER SHUTDOWN.......................................... 34

19. FREEZE PROTECTION ......................................... 34

System Drain-Down ..............................................34

Continuous Pump Operation .................................34

20. MAINTENANCE ..................................................... 34

Air Coil Cleaning ...................................................35

Cabinet Care (optional) ......................................... 35

Unplug Condensation Drain Holes ........................35

21. TROUBLESHOOTING ........................................... 35

22. SERVICE CALL VERIFICATION ........................... 36

Power Supply ........................................................ 36

Water Flow ............................................................ 36

Time Clock Adjustment .........................................36

Set Factory Defaults..............................................36

Service Access to Heaters .................................... 37

23. PLUMBING DIAGRAMS ........................................ 38

24. RESISTANCE SENSOR VALUES ......................... 42

25. CONNECT TO WI-FI WITH RAYMOTE ................. 43

26. RAYMOTE MOBILE APP ....................................... 48

27. EXTERNAL CONTROL OUTPUTS ....................... 71

28. REPLACEMENT PARTS ....................................... 84

29. ILLUSTRATED PARTS LIST ................................. 85

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

4

1. WARNINGS

Pay Attention to these Terms

ADANGER Indicates the presence of immediate hazards which will cause severe personal injury, death or substantial

property damage if ignored.

AWARNING Indicates the presence of hazards or unsafe practices which could cause severe personal injury, death or

substantial property damage if ignored.

ACAUTION Indicates the presence of hazards or unsafe practices which could cause minor personal injury or product

or property damage if ignored.

CAUTION CAUTION used without the warning alert symbol indicates a potentially hazardous condition which could

cause minor personal injury or product or property damage if ignored.

NOTE Indicates special instructions on installation, operation, or maintenance which are important but not related

to personal injury hazards.

CAUTION: Improper chemical content in a swimming

pool or spa can damage the heater. DO NOT add pool/

spa chemicals to the pool/spa via the skimmer or any

other apparatus (feeder, chlorinator, etc.), that is on the

inuent side (i.e. before) of the heater. This will damage

the heater and could void the heater warranty. ALWAYS

follow the product manufacturer’s directions when

adding any chemicals to your pool.

This manual, as well as the pool heater itself, contains ANSI-approved product safety signs and labels. Please read these signs

and labels, as they convey important safety information about hazards that may be potentially present in and around the heater.

ACAUTION: Elevated water temperature can

be hazardous. The U.S. Consumer Product Safety

Commission has these guidelines:

1. Spa water temperatures should never exceed 104°F

(40°C). A temperature of 100°F (38°C) is considered

safe for a healthy adult. Special caution is suggested

for young children.

2. Drinking of alcoholic beverages before or during spa

or hot tub use can cause drowsiness which could

lead to unconsciousness and subsequently result in

drowning.

3. Pregnant Women Beware! Soaking in water over

102°F (39°C) can cause fetal damage during the first

three months of pregnancy resulting in the birth of a

brain-damaged or deformed child. Pregnant women

should stick to the 100°F (38°C) maximum rule.

4. Before entering the spa or hot tub, users should

check the water temperature with an accurate

thermometer; spa or hot tub thermostats may err

in regulating water temperatures by as much as 4°F

(2.2°C).

5. Persons with a medical history of heart disease,

circulatory problems, diabetes, or blood pressure

problems should obtain a physician’s advice before

using pools or hot tubs.

6. Persons taking medications which induce

drowsiness, such as tranquilizers, antihistamines,

or anticoagulants, should not use spas or hot tubs.

AWARNING: These heat pump pool heaters are

charged with R-410A refrigerant. Ensure that all service

work is done with gauges and equipment suitable for

R-410A.

EFFICIENCY TESTING NOTICE: For purposes of

verifying or testing efciency ratings, the test procedure

in Title 10 APPENDIX P to Subpart B of Part 430 (Uniform

Test Method for Measuring the Energy Consumption of

Pool Heaters) and the clarifying provisions provided in

the AHRI Operations Manual 1160 that were applicable

at the date of manufacture should be used for test set

up and performance. Charging Chart are available at

https://www.raypak.com/customer-support/heat-pump-

charging-charts. These should only be used by certied

HVAC technicians to check or adjust refrigerant charge

for proper operation.

CAUTION: The appliance is not to be used by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction.

Do not allow children to play near or with appliance,

severe damage can occur from moving parts.

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

5

2. INTRODUCTION

AWARNING: This heat pump pool heater is an

electromechanical machine that incorporates a

pressurized refrigerant gas in a sealed system. ONLY

trained and qualied service personnel are authorized to

install or service this equipment. Without proper training

and knowledge of such equipment, any attempt to install or

service the unit could result in serious injury or even death.

This manual contains important information on the use,

maintenance and troubleshooting of your new heat

pump pool heater. This unit must be properly installed,

maintained and operated for optimal performance.

This heater is an extremely efcient, economical machine

designed specically for heating swimming pools. It is

similar in design and operation to a typical residential air

conditioning system. The unit employs a hermetic motor/

compressor operating in a refrigeration cycle to extract

heat from ambient air and deliver it to the circulating pool

water.

All heat pump pool heaters have a lower BTU/hr heating

capacity than a gas-red or oil-red heater for the same

pool and will have to operate more hours per day to keep

the pool at setpoint. It may operate up to 24-hours a day

at certain times. It is designed to do so. Even with long

runtime hours, it will heat the pool at less cost than other

heaters using fossil fuel.

Since evaporation is the main cause of heat loss from a

pool, keeping the pool covered whenever it is not in use will

greatly reduce the cost of keeping the pool heated. Even

during warmer weather, Raypak recommends keeping the

pool covered at night.

NOTE: 4x Hurricane tie-down brackets, 16x tie-down

screws, 2x union halves, the printed warranty, optional

harnesses and the I&O manual are located in an

accessory bag mounted on the front of the heater

inside the packaging. For Heat Only models, a check

valve is provided in the packaging. For Heat/Cool

models, a bypass assembly is provided. Please DO

NOT throw away the packaging before removing all of

their contents.

ATTENTION: Please Take This Opportunity

to Quickly Register Your Unit!!

While your unit is being installed by your professional and

licensed installer of choice, Please Take This Opportunity to

Quickly Register Your Unit!! With the necessary information

in hand, Registering your new Heat Pump Pool Heater only

takes a few moments and is the only way to assure any

veriable warranty procedures during the span of your unit’s

period of protection.

Using Figure 1, please locate and record your model and

serial number. Once you have done this, please make sure

you also have the following information on hand:

• Name, phone number, and email address of

homeowner

Figure 1. Model and Serial Number Location

Warranty Registration Conrmation #:

Scan this QR with your smart device to register or verify

your new Raypak heater.

Nameplate

QR Code

• Physical address of where the unit is installed; please

include any ‘subdivision’ or similar information

• Any service challenges present at the house/

neighborhood: gated community, locked access at

house, guard dog, etc.

• Date of installation of the new unit

• Name and phone number of the professional and

licensed entity that performed the installation for you

With all of the above information in hand, please contact

Raypak and ask to register your brand new heat pump or

Online at:

https://www.raypak.com/support/registration_warranty/

You will be given a Warranty Registration Conrmation

number which you should notate and keep in one location

along with your Installation & Owner’s Manual, a copy of

your warranty (provided with your manual) and the above

information.

This unit is equipped with a QR Code on the rating plate, as

shown in Figure 1, which will take you to the www.raypak.com

website where the Installation & Owner’s manual and other

documents can be easily accessed.

This would also be a good time to review both the manual

and the warranty so that you are aware of how to correctly

operate your new equipment as well as how to keep from

voiding any aspects of your warranty. During the life of your

unit, please feel free to use the phone number conveniently

located right on the unit, to contact us with any questions you

may have about operation, warranty, and/or service.

Thank you very much choosing Raypak to satisfy your pool

heating needs!!

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

6

Recommended Level(s) Fiberglass Pools Fiberglass Spas Other Pool & Spa Types

Water Temp. 68 °F to 88 °F

(20°C to 31°C)

89 °F to 104 °F

(32°C to 40°C)

68 °F to 104 °F

(20°C to 40°C)

pH 7.3 to 7.4 7.3 to 7.4 7.6 to 7.8

Total Alkalinity (PPM) 120 to 150 120 to 150 80 to 120

Calcium Hardness (PPM) 200 to 300 150 to 200 200 to 400

Salt (PPM) 4500 MAXIMUM 4500 MAXIMUM 4500 MAXIMUM

Free Chlorine (PPM)* 2 to 3 2 to 3 2 to 3

Total Dissolved Solids (PPM) 3000 MAXIMUM** 3000 MAXIMUM** 3000 MAXIMUM**

Water Pressure (psi/kPa) 5 MIN. - 70 MAX.

(35 MIN. - 483 MAX.)

5 MIN. - 70 MAX.

(35 MIN. - 483 MAX.)

5 MIN. - 70 MAX.

(35 MIN. - 483 MAX.)

*Free Chlorine MUST NOT EXCEED 5 PPM!

** In salt water chlorinated pools, the total TDS can be as high as 6000 ppm.

Table A. Water Chemistry

3. WATER CHEMISTRY

IMPORTANT: Corrosive water voids all

warranties.

For your health and the protection of your pool equipment,

it is essential that your water be chemically balanced. The

following levels must be used as a guide for balanced

water.

• Occasional chemical shock dosing of the pool or spa

water should not damage the heater providing the

water is balanced. However, it is highly recommended

that the heat pump pool heater is isolated via shut off

valves before any aggressive chemical treatment.

• Automatic chemical dosing devices and salt

chlorinators are usually more efficient in heated

water. Unless controlled, they can lead to excessive

chlorine level which can damage your heater.

• Further advice should be obtained from your pool

or spa builder, accredited pool shop, or chemical

supplier for the correct levels for your water.

4. INSTALLATION

CONSIDERATIONS

AWARNING: Do not install the unit within 3 ft (0.9 m) of

fossil-fuel-burning heaters. Air intake along the sides of

this heat pump pool heater could disturb the combustion

process of the unit, and could cause damage or personal

injury.

● Mount the unit on a level, sturdy base, preferably a

concrete slab. The size of the base should be at least 3 ft

by 3 ft (0.9 m x 0.9 m) - slightly larger if hurricane tie-down

brackets are installed. See Figure 4 for more details.

CAUTION: The unit’s supporting base must be high

enough to keep it completely free of standing water at

all times.

Situate the heater carefully to minimize installation costs

while providing maximum efciency of operation, and to

allow adequate service access, as follows:

• For unrestricted air intake and service access,

position each side of the unit at least 1 ft (30 cm)

from walls, pipes and other obstructions.

AWARNING: This unit is designed for outdoor

installation. It is NOT certied for indoor installation.

DO NOT install it in an enclosed area such as a shed or

garage, or under a porch or deck.

• This unit features an ‘up-flow’ discharge for quiet

operation. Air is pulled up through the evaporator

coil and discharged through the top grill. Allow

at least 5 ft (1.5 m) clearance above the unit for

unrestricted air discharge. Do NOT install the

unit under a porch or deck. Refer to Figure 2 for

installation clearances. Allowing cold discharge air to

recirculate back into the evaporator coil will greatly

reduce the unit’s heating capacity and efficiency.

To minimize water piping, locate the unit as close as

possible to the existing pool pump and filter.

• Irrigation water should be directed away from the

heat pump pool heater - irrigation water spray can

damage the heater.

• Rain water runoffs - the unit is designed to operate

outdoors and can be exposed to rain. However, rain

water runoff falling directly onto the unit can cause

damage and/or shorten the life of your unit. Such

damage is NOT covered under warranty. Install rain

gutters or rain diverters on your roof if the unit is

installed in a position where contact with rain runoff

may occur.

• It is important to keep the area next to the heater

clear of shrubs, bushes and chemicals containers.

They could prevent air from circulating fully through

the heater, and will affect the operation of the heater

or damage the heater.

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

7

3 FT

(09.m)

MIN

AIR

FLOW

IN

AIR

FLOW

IN

AIR FLOW OUT

60" (1.52m) MIN

12"

(0.3m)

MIN

Figure 2. Installation Clearances

• When installed in areas where freezing temperatures

can be encountered, drain the water circuit to

prevent possible freeze-up damage. Refer to "Freeze

Protection" on page 34 for proper procedures.

• If the heater is located below the water line of the

pool, the Water Pressure Switch (WPS) or Water

Flow Switch (WFS) might need to be adjusted or an

external WFS might be needed.

• For high-wind installation requirements, refer to

Figure 4 – depending on the model size.

Figure 3. Base Design - Handling

NOTE: The base is designed with recessed areas

to allow the use of hand trucks or lifting without the

possibility of pinching ngers as shown in Figure 3.

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

8

UNIT HEIGHT

37.8” MAX

UNIT WIDTH

33.6” MAX

UNIT LENGTH

33.6” MAX

CONCRETE SLAB

BY OTHERS, TYP.

UNIT WIDTH

33.6” MAX

UNIT LENGTH

33.6” MAX

UNIT HEIGHT

37.8” MAX

CONCRETE SLAB

BY OTHERS, TYP.

CONTROL

COVER

3

Maximum Rated Wind Pressures:

± 140 psf Lateral, 111 psf Uplift

Hurricane tie-downs are a structural component designed to prevent wind uplift during severe weather, such as hurricanes or severe storms. For further information on tie-downs,

and technical support, contact Raypak at www.raypak.com or call 805-278-5300.

Minimum pad dimensions are 43-1/4”

x 43-1/4” x 4” thick.

Screws to attach brackets to unit are

supplied with the unit.

DO NOT use screws not specified or

provided by manufacturer. Screws

are stainless steel #10 x 3/4”

self-drilling. Each bracket requires 4

screws attached to the unit.

Miami Tech Clip: (0.07”) ASTM A653

Fu=90 KSI Steel (CUTD10) or 0.080”

5052-H32 Aluminum (CUTDA10). Florida

approval FL# 19731.1 or approved equal.

TIE-DOWN SCHEDULE

At-Grade ± 54 psf (0 psf) 4

At-Grade / Rooftop ± 140 psf (111 psf) 8

# of

Tie-Down

Clips

Installation

Condition

Max. ASD

Wind Pressures

Lateral (Uplift)

1.26 TYP.

32.5 TYP.

1.26 TYP.

Tie-Down Clips

Tie-Down Clips Tie-Down Clips

Tie-Down Clips

# of

Tie-Down

Clips

8.00”- 10.00”

Figure 4. Hurricane Tie Down Instructions – Models: TWPH 4550, 5550, 6550, 6550EHC, 8550, & 8550EHC

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

9

5. WATER CONNECTIONS

CAUTION: The heater inlet and outlet are NOT

interchangeable. They must be connected as instructed

below.

A

WARNING: Improper installation of any type of

automatic chemical feeders can result in serious damage

to, or premature failure of, the heater and such damage

will not be covered under warranty. Install a check valve

and/or a Hartford loop AFTER the heater and BEFORE

any chlorinating devices. Install any automatic chemical

feeders AFTER the heater.

1. Connect the heater in the return water line between

the filter and the pool/spa. See plumbing diagrams

on page 38 (without bypass) and page 39 (with

bypass).

2. Connect the filter outlet to the fitting marked INLET at

the bottom front of the unit.

3. Connect the fitting marked OUTLET to the return

piping to the pool/spa. Unit inlet/outlet connection

fittings are 2-inch PVC unions on models 4550-8550.

Water connections from the unit to the main return line can

be PVC pipe or exible pipe approved for the purpose and,

in either case, should be at least equal in size to the main

pool/spa circulation piping.

• Water flow to the unit will exceed 40 GPM (151 LPM)

for 4550 models or 50 GPM (189 LPM) for 5550-

8550 models. See Figure 63 for bypass instructions.

• To protect (completely bypass) the unit from any

harmful chemical treatments (i.e. Acid wash, back-

to-back super chlorinators, stain treatments, etc.); or

to be able to isolate the unit for service/repair or

freeze preparation and still allow pool/spa circulation

to continue.

In Heat/Cool models, a bypass assembly is included.

Please refer to the plumbing on page 39, for further

instruction.

Please note that some municipalities do not allow the use

of a shutoff valve on the efuent/outlet side of any heating

equipment, especially when there is one on the inlet side.

These entities typically instead allow a PVC tee and spring

check valve on the efuent/outlet side. This is allowed

by Raypak and can also double as your protection from

chemical feeders and chlorinators that are downstream of

the unit.

4. Operate the pump and check the system for leaks.

5. Drain plugs are located on each union fitting as shown

in Figure 5 for draining the system during winterizing.

NOTE: While it is possible to mount the upper union

with the drain plug vertically, the manufacturer has

determined that installing both unions with the drain

plugs facing down, as shown in Figure 5, provides for

the best draining of the system.

Figure 5. Water Connections/Drain Plugs

CAUTION: When the drain plugs are removed for

draining the system, ensure that they are stored in a

safe place for re-installation when needed to restart the

system.

6. FLOW RATE & PRESSURE

DROP

For system pressure drop information, see Table B.

Flow

GPM (LPM)

Pressure Drop (PSI)

4550 5550 6550/

6550EHC

8550/

8550EHC

20 (750) 3.4

30 (113) 7 4 6 9

40 (151) 13 7 9 9

50 (189) 10 10 10

60 (227) 11 11 11

70 (265) 12 12 12

80 (303) 13 13 13

Note: Minimum recommended ow is 20 GPM. Multiply the pressure drop

in psi by 2.3067 to yield the pressure drop in Ft. H2O Head.

(Total Dynamic Head TDH)

Table B. Flow Rate & Pressure Drop Across the Heater

INLET

OUTLET

DRAIN PLUG

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

10

Model No. Power

Min.

Circuit

Ampacity

Breaker Size

(AMP) Recommended Wire Length from Breaker to Heater*, ft. (m)

MAX. 12 AWG 10 AWG 8 AWG 6 AWG 4 AWG

4550

208/230V -

Single Phase

- 60Hz

38 60 NR** 89 (27.1) 142 (43.3) 225 (68.6) 359 (109.4)

5550 40 70 NR** 94 (28.7) 151 (46.0) 239 (72.8) 383 (116.7)

6550 46 70 NR** 97 (29.6) 156 (47.5) 247 (75.3) 396 (120.7)

8550 46 70 NR** NR** 110 (33.5) 175 (53.3) 280 (85.3)

* Reference only - see National Electrical Code or local codes for wire gauge length limits.

** NR= Not Recommended

Table C. Typical System Electrical Power Requirements

7. ELECTRICAL

CONNECTIONS

Refer to the unit rating plate below the control panel for

precise power requirements for your unit, and for ampacity

and over-current protection requirements.

All wiring must be in accordance with the National Electrical

Code, NFPA No. 70, latest edition, and all applicable state

and local codes. See wiring diagram on page 11.

AWARNING: This unit MUST be installed using

exible conduit for supply wiring to the unit. This will

allow movement of the conduit whenever the junction

box is removed for service - see "Service Access to

Heaters" on page 37.

• Locate the equipment disconnect means within 3

feet (0.9 m) of the heater’s electrical enclosure, or

as close to the heater as possible. Always satisfy

applicable codes and standards.

• A means to fully disconnect the unit from the main

power supply must be incorporated in the wiring of

the unit.

NOTE: Refer to the National Electrical Code, Article

680, for general requirements for swimming pools and

equipment, and to Article 440 for special considerations

necessary for circuits supplying hermetic refrigeration

motor/compressors.

• In sizing power wiring, be especially aware of up-sizing

requirements necessary due to wiring distances.

Always satisfy applicable codes and standards.

• Connect electrical Line 1 (L1) and Line 2 (L2) to

the terminals indicated in Figure 6 for proper wiring.

Electrical installation should be performed by a

licensed electrician only.

This unit is compatible to work with external control

systems, (optional harness provided in the packaging

per NOTE on page 5) heat-on-demand options and other

external time clock overrides. Refer to the external control

system’s instructions, and "Remote Mode Selector", on

page 31 of this manual, for installation information.

An earth ground lug is located to the right-side of the water

connections.

L1 GND

L2

For 208v operation, ensure to

change the transformer to the

208 and C terminals.

Figure 6. Terminals L1 and L2

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

11

USE COPPER WIRES ONLY

USE 75°C 600V WIRE

TORQUE SCREWS: 40 IN-LB

11

1

10K

100K

BK/BU

BK/RD

RD

GN

GN/BK

GN

1 1

BN

BU

YE

BN

RD

YE

OG

BN

YE

BN

YE

R V

BU

RD

C

F

H

C

F

H

1

`

YE

BU

YE BU

VT

24VAC

208V

240V

T1

L1

T2

L2

C2

C1

CONTACTOR

T1

L1

T2

L2

C2

C1

CONTACTOR

C

S

R

C

S

R

COMPRESOR

C

S

R

COMPRESOR

RD

BK

RD

POWER SUPPLY:

208/240V – 1 PHASE – 60Hz

L1 L2

GND

FAN

MOTOR

WPSLPSHPS

YE

BK

RD

BK

OG

BN

C2

C1 14

36

C2

C1 14

36

GY

BK/WH

RD/WH

BN

11

3A 3A

RS-485

COMM

OUTLET

TEMP

P12 P13 P10 P6

FLOW

SENSOR

TEMPERATURE

SENSORS

P16

USER INTERFACE

P7

REMOTE

SELECTOR

POWER

24VAC

P1

MAIN

FUSE

VALVES

FUSE

F1

F2

VARIABLE

SPEED PUMP

P8

PUMP

P5

P19P20

3-WAY

VALVE2

3-WAY

VALVE1

AUX2

AUX1

P4

P3

P11

P9

P2

FAN, REV. VALVE AND

COMPRESOR COIL

FAN RVS COMP

SOLAR

3-WAY VALVE

SAFETY SWITCHES

WPS LPS HPS

3A 3A

RS-485

COMM

OUTLET

TEMP

P12 P13 P10 P6

FLOW

SENSOR

TEMPERATURE

SENSORS

P16

USER INTERFACE

P7

REMOTE

SELECTOR

POWER

24VAC

P1

MAIN

FUSE

VALVES

FUSE

F1

F2

VARIABLE

SPEED PUMP

P8

PUMP

P5

P19P20

3-WAY

VALVE2

3-WAY

VALVE1

AUX2

AUX1

P4

P3

P11

P9

P2

FAN, REV. VALVE AND

COMPRESOR COIL

FAN RVS COMP

SOLAR

3-WAY VALVE

SAFETY SWITCHES

WPS LPS HPS

MODESERVICE DOWN

UP CONNECT

MODESERVICE DOWN

UP CONNECT

BN

BN/OG

YE

BU

1

COMPONENT CODE

SENSOR 10K

DUAL SENSOR 100K

PRESSURE SWITCH

R VREVERSING VALVE

CAPACITOR

GROUND

FAN RELAY

24VAC

TRANSFORMER

WIRE COLOR CODE

WPS WATER PRESSURE

SWITCH

HPS HIGH PRESSURE

SWITCH

LPS LOW PRESSURE

SWITCH

GND GROUND LUG

BK

BN

BU

GN

GY

VT

OG

RD

WH

YE

BLACK

BROWN

BLUE

GREEN

GRAY

VIOLET

ORANGE

RED

WHITE

YELLOW

OUTLET

INLET

COIL

AMBIENT

INSERT

A

NC NO COM L1 L2 L2

VOLTAGE MONITOR

NC NO COM L1 L2 L2

VOLTAGE MONITOR

L1 L2TRANSFORMER

NC NO COM L1 L2 L2

VOLTAGE MONITOR

L1 L2TRANSFORMER

INSERT

A

NC NO COM L1 L2 L2

VOLTAGE MONITOR

L1 L2TRANSFORMER

BK/BU

BK/RD

RD

GN

GN/BK

GN

VT

(HEAT/COOL ONLY)

24VC

208V/230V Single-Phase – Heat only and Heat/Cool models

8. WIRING DIAGRAM

Figure 7. Heat Only and Heat/Cool Models Wiring Diagram

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

12

9. HEATER CONTROL

DISPLAY

The heater display is located in the front panel of the heat

pump, covered with a door. All operation and settings of

the heater control are accomplished through the use of the

ve (5) touch keys of the user interface. These keys are

displayed in Figure 8.

Mode Key

The Mode Key is used to select one of several modes

for pool or spa operation. It also allows the user to select

the OFF mode of operation, during which the LCD, while

displaying OFF, continues to show the water temperature.

Refer to section 10, "Operation Modes" for details.

UP and DOWN Keys

If the heater is in pool or spa mode, the desired water

temperature (SETPOINT), can be adjusted using the UP

or DOWN keys.

MODESERVICE DOWN

UP CONNECT

CONNECT MENU

SERVICE MENU

Control 1.0

UI 1.0

UP TEMP ADJUST

DOWN TEMP ADJUST

MODE KEY

Figure 8. Heater Control Display

The display shows information on a 2-line, 16-character

back-lit Liquid Crystal Display (LCD). The back-light is

normally off, but it turns on for 5-minutes after power-up

and for 5-minutes after any button press. Use the LCD to

set up and monitor the operation of your heater.

If the control keys remains inactive for 5-minutes, the

screen will revert to the current view.

On a normal power-up, the control displays the current

software revision on the LCD for 2-seconds and then

resumes the user-selected mode it was in before power

was interrupted.

If unit type has not been set (like during the replacement

of the control), the control prompts the user to set the

model type (Heat Only or Heat/Cool) before any device

operation is enabled.

Upon initial installation, there are several items that

can be dened and programmed depending on the

conguration and accessories intended to be controlled

by the heater. Refer to "Program Menu" section on page

17 for details.

10. OPERATION MODES

The user may select one of several operating modes.

Each mode is selected by pressing the MODE key to cycle

between the modes. Each press of the MODE key selects

the next mode.

On Heat Only models, the options available by pressing

the MODE key are POOL, SPA, TIMED SPA and OFF.

On Heat/Cool models, the options available by pressing

the MODE key are POOL COOL, POOL HEAT, POOL

AUTO, SPA, TIMED SPA and OFF.

OFF

Water Temp 68F

OFF 8:05P

Water Temp 68F

OFF

No Demand

OFF

No Demand

8:05P

Figure 9. Alternating Display

Pool [Heat] and Spa Modes

The control is equipped with a Pool (heat) and Spa modes

which will automatically heat the pool to the heating

setpoint established in the selected mode.

The top row of the LCD displays the operation mode and

temperature setpoint. When Pool (heat) or Spa mode is

selected, each press of the UP or DOWN key will increase

/ decrease the water heating setpoint temperature. Holding

the UP or DOWN keys down will speed up the change of

the temperature values.

In these modes, the heater is set to heat when the water

temperature is 1°F (0.5°C) degree below the selected

temperature (setpoint). Heating is terminated when

setpoint is reached.

When the water temperature is above the setpoint, the

LCD will alternate “Water Temp” with “No Demand.” When

the water temperature is below the setpoint and the unit is

heating, the LCD will alternate “Water Temp” with “Heating”.

In POOL mode, default temperature setpoint is 80°F

(27°C) with a maximum temperature limit of 95°F (35°C).

In SPA mode, the default temperature setpoint is 100°F

(38°C). with a maximum temperature limit of 104°F (40°C).

Refer to "Program Menu", on page 18, to adjust pool or

spa maximum temperature limits.

Pool set 85F

Heating

Pool set 85F

Heating

Pool set 85F

Water Temp 68F

Pool set 85F

Water Temp 68F

Spa set 100F

Heating

Spa set 100F

Heating

Spa set 100F

Water Temp 68F

Spa set 100F

Water Temp 68F

Figure 10. Pool Heat and Spa Modes

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

13

Timed Spa Mode

The control is equipped with a mode which will heat the

spa to the Spa setpoint temperature for a specied period

of time selected in the TIMED SPA mode setup.

A

WARNING: If an external controller controls the spa

heating in a pool/spa system, manual adjustment of the

3-way valves may be necessary to use the TIMED SPA

feature of this heat pump. Failure to adjust the 3-way

valves properly may result in pool water overheating or

other undesirable results.

To activate the timed spa feature, press the MODE key until

“TIMED SPA” is displayed on the top line of the display.

The display will read “Up or Dn to Set”. This tells the user

to press the UP or DOWN keys to set the desired length of

time for the timed spa heating operation.

Press the UP or DOWN keys to select the desired duration

of spa heating, up to a maximum duration of 6-hours in

15-minute increments. After selection of time is completed

press MODE key to start heater operation.

The timer will start to count down from the selected period

and the unit will operate to heat the water based on the

previously selected spa setpoint temperature setting.

Once the unit turns on, the display will toggle between the

current spa water temperature and the current operating

state “Heating” and the timer.

The top row of the LCD displays the operation mode and

temperature setpoint. Timed Spa temperature setpoint

can be adjusted using the UP and DOWN keys while the

screen is displaying the Water Temperature and “Heating”

status.

To adjust the timer, press MODE key, then use the UP and

DOWN keys to increase or decrease the timer. To terminate

the timer, use DOWN key to set timer to 00:00:00.

When the TIMED SPA timer has expired, the control will

be set to OFF.

Timed Spa 100F

Up or Dn to Set

Timed Spa 100F

Up or Dn to Set

Timed Spa 100F

Heating 2:30:00

Timed Spa 100F

Heating 2:30:00

Timed Spa 100F

Water Temp 68F

Timed Spa 100F

Water Temp 68F

Figure 11. Timed Spa Mode

Pool Cool Mode - Heat/Cool Models Only

In heat/cool models, the control is equipped with a "Pool

Cool Mode" which will automatically cool the pool to the

cooling setpoint established in this mode.

The top row of the LCD displays the operation mode and

temperature setpoint. When pool cool mode is selected,

each press of the UP or DOWN key will increase /

decrease the water cooling setpoint temperature. Holding

the UP or DOWN keys down will speed up the change of

the temperature values.

In this mode, the heater is set to cool when the water

temperature is 1°F (0.5°C) degree above the selected

temperature (setpoint). Cooling is terminated when

setpoint is reached.

When the water temperature is below the setpoint, the

LCD will alternate “Water Temp” with “No Demand.” When

the water temperature is above the setpoint and the unit

is cooling, the display will alternate “Water Temp” with

“Cooling”.

In pool cool mode, default temperature setpoint is 80°F

(27°C) with a minimum temperature of 44°F (7°C) and

maximum temperature limit of 95°F (35°C). Refer to

"Program Menu", on page 18, to adjust pool maximum

temperature limits.

Pool Cool 85F

Cooling

Pool Cool 85F

Cooling

Pool Cool 85F

Water Temp 95F

Pool Cool 85F

Water Temp 95F

Figure 12. Pool Cool Mode

Pool Auto Mode - Heat/Cool Models Only

The control is equipped with a mode which will automatically

heat and cool the pool within the range of the heating

setpoint and the cooling deadband.

The top row of the LCD displays the operation mode and

temperature setpoint. When pool auto mode is selected,

each press of the UP or DOWN key will increase /

decrease the water setpoint temperature. Holding the UP

or DOWN keys down will speed up the change of the

temperature values.

In these modes, the heater is set to heat when the water

temperature is 1°F (0.5°C) degree below the selected

temperature (setpoint). Heating is terminated when

setpoint is reached. The heater is set to cool when the

water temperature is above the selected temperature

(setpoint) plus the specied cooling deadband. Cooling

is terminated when setpoint plus the cooling deadband is

reached.

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

14

Example: When pool auto setpoint is set at 80°F (27°C)

and cooling deadband set at 6°F (3.5°C), the unit will

automatically heat the pool if the temperature drops below

80°F (27°C), and will automatically cool the pool if the

temperature is above 86°F (30.5°C).

In pool auto mode, default temperature setpoint is 80°F

(27°C) with a minimum temperature of 44°F (7°C) and

maximum temperature limit of 95°F (35°C). Cooling

deadband default is 6°F (3.5°C), adjustable from 2 to 10°F

(1 to 5.5°C) degrees. Refer to "Program Menu", on page

18, to adjust pool maximum temperature limits and

cooling deadband.

Pool Auto 85F

Heating

Pool Auto 85F

Heating

Pool Auto 85F

Water Temp 83F

Pool Auto 85F

Water Temp 83F

Pool Auto 85F

Cooling

Pool Auto 85F

Cooling

Pool Auto 85F

Water Temp 92F

Pool Auto 85F

Water Temp 92F

Figure 13. Pool Auto Mode

Control Lockout Mode

Prevent unauthorized access to the heater's control

settings with the "Control Lockout" feature. To activate

the lockout, press and hold the MODE and DOWN keys

simultaneously for 5-seconds. Select a three-digit PIN by

using the UP and DOWN keys to select each digit and the

MODE key to lock in the selection. Conrm your selection

and make a record of your PIN for future reference.

Control Lockout

Enter PIN 000

Conﬁrm Lockout

Yes

Figure 14. Control Lockout

NOTE: Record this lockout code for future reference.

To unlock the controls, select the ENTER PIN menu by

pressing the MODE key followed by the UP or DOWN key.

Enter the three-digit PIN that was previously used to lock

the control. Please note that power cycling will not clear

the lockout. A successful PIN entry will display "LOCKBOX

CLEARED," whereas an incorrect PIN will result in

"INVALID PIN" being displayed.

If the user-selected PIN is lost or does not clear the

Control Lockout, you can use the Code 101 to temporary

override the lock box and then the Program Menu to SET

FACTORY DEFAULTS. This will remove the PIN and allow

normal operation, including the selection of a new PIN if

desired. Refer to the "Program Menu" section on page 16

for detailed instructions.

NOTE: If you choose to set FACTORY DEFAULTS, the

pool and spa setpoints will return to their default values

of 85°F (29°C) and 100°F (38°C), respectively, and the

maximum temperature settings for pool and spa will be

reset to 95°F (35°C) and 104°F (40°C). It will be necessary

to readjust these setpoints to your preferred settings.

Additionally, other default congurations will be restored.

Keypad Protection

After 30-minutes of inactivity, the controller will automatically

protect the keypad to avoid unintended key presses. Follow

the on-screen instructions to unlock the keypad: Press the

UP key three times, followed by the MODE key, to unlock.

11. SERVICE MENU

To access the "Service Menu" and fault history, press the

SERVICE key 1-time. The heater will continue to operate

while in the service menu.

In this mode, pressing the UP or DOWN keys will toggle

through the various information reported. Some items

("Fault History" and "Sensor Temperatures") have multiple

values. Press UP or DOWN buttons to scroll through the

additional information. The SERVICE menu may be exited

to return to the previous display be pressing the MODE

key or it will automatically be exited if no key is pressed

within 30-seconds.

Supply Voltage

The rst screen displayed is the "Supply Voltage" indicator,

which indicates the voltage supplied to the control board.

Normal readings range from 24 to 30 volts.

Brownout Detect.

230V

Supply Voltage

24V

Figure 15. Supply Voltage Indicator

Run Time Hours and Cycles

Press the DOWN key. The "Hours" run time indicates the

total hours of operation for the pool heater, as measured

by the amount of time that the compressor has been

energized. The "Cycles" count indicates the number of on/

off cycles of the heater, as measured by the number of

times the compressor has been energized.

Brownout Detect.

230V

Hours 451

Cycles

89

Figure 16. Run Time/Cycles

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

15

Faults History

Press the DOWN key. The "Fault History" displays up to ten

faults in memory. The order of the faults begins with "Last

Err", which is the most recent fault, and proceeds through

the ten most recent messages in reverse chronological

order.

Run time hours at the moment of the fault are displayed

at the end of the rst line. The second line of the display

shows the "Fault" message. If there are no faults in the

history buffer, the second line reads “All Faults Clear.”

Brownout Detect.

230V

Last Err 450

Brownout Detect.

230V

Fault 9 241

Inlet Temp Fail

Brownout

or

Brownout Detect.

230V

Last Err 0

All Faults Clear

Figure 17. Fault History

Press the Service key again to access the Advance

Service Menu.

Heat Pump Temperatures

The "In/Out Temp" screen indicates the water temperature

sensed in the inlet and at the outlet of the heater.

Brownout Detect.

230V

HPPH Temp

In 68F, Out 78F

Figure 18. Inlet and Outlet Temperature

Coil and Outdoor Temperature

Press the DOWN key. The "Coil Temp" screen indicates

the temperature sensed, displayed on the rst line. The

second line displays the temperature sensed by the

outdoor sensor.

Brownout Detect.

230V

Coil Temp

Outdoor 68F

47F

Figure 19. Coil and Outdoor Temperature

Solar Heater Temperature

(Heat/Cool Models Only)

Press the DOWN key. When enabled from "Installers

Menu", the "Solar Temperature" screen indicates the

temperature sensed with the solar heater sensor. The

"In" reading indicates the inlet of the solar heater. Solar

inlet temperature readings should come from a eld-

supplied 10K temperature sensor. Solar "Out" displays the

temperature at the outlet of the solar heater. This reading

comes from the Heat pump inlet sensor. This screen is

only displayed if the option “Solar Heating” is enabled

from "Installers Menu". For more details about solar heater

integration refer to section 13 Installers menu on page

21.

Brownout Detect.

230V

Solar Temp

In 61F, Out 68F

Figure 20. Solar Heater Temperature

Pump Status

Press the DOWN key. When enabled from "Installers

Menu", the "Pump Status" screen indicates current pump

mode and speed selection.

Pump control is compatible with Raypak Protégé Variable-

speed Pump and 4 digital outputs speed selector. By

default, "Pump Control" is disabled. See page 21 to

select and congure "Pump Control" option.

Brownout Detect.

230V

Protégé Pump

Speed2 1500 RPM

Brownout Detect.

230V

Pump Status

Speed 2

Figure 21. Pump Status

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

16

OFF mode

POOL Auto mode

Supply Voltage

Run Counters

Faults History

Inlet & Outlet

Temperatures

Pump Status

SERVICESERVICE

MODEMODE

SERVICESERVICE

UPUP

DOWNDOWN

UPUP

DOWNDOWN

Pool Cool 80F

Cooling

Pool Auto 80F

Cooling

OFF 8:05PM

No Demand

OFF 8:05PM

No Demand

Pool Heat 80F

Heating

Pool Auto 80F

Heating

Protégé Pump

Speed2 1500 RPM

Protégé Pump

Speed2 1500 RPM

HPPH Temp

In 68F, Out 108F

HPPH Temp

In 68F, Out 108F

Hours 451

Cycles 89

Hours 451

Cycles 89

Supply Voltage

26V

Supply Voltage

26V

Available in some

configurations and kits

or

Last Err 0

All Faults Clear

Last Err 0

All Faults Clear

Fault 9 241

Brownout

Fault 9 241

Brownout

Last Err 450

Inlet Temp Fail

Last Err 450

Inlet Temp Fail

SPA mode

MODEMODE

Spa set 100F

Heating

Spa set 100F

Heating

POOL Cool modeAdjust

Temperature

UPUP

DOWNDOWN

Pool Cool 80F

Cooling

Pool Cool 80F

Cooling

POOL [Heat] mode

MODEMODE

Pool Heat 80F

Heating

Pool Heat 80F

Heating

OFF 8:05PM

Water Temp 68F

OFF 8:05PM

Water Temp 68F

Adjust

Temperature

UPUP

DOWNDOWN

Adjust

Temperature

UPUP

DOWNDOWN

MODEMODE

Adjust

Temperature

UPUP

DOWNDOWN

Timed SPA mode

Timed Spa 100F

Up or Dn to Set

Timed Spa 100F

Up or Dn to Set

Adjust Duration

UPUP

DOWNDOWN

Adjust

Temperature

UPUP

DOWNDOWN

Timed Spa 100F

Heating 2:30:00

Timed Spa 100F

Heating 2:30:00

MODEMODE

Options available only

in Heat/Cool models

Coil & Outdoor

Temperatures

Coil Temp 47F

Ambient Temp 68F

Coil Temp 47F

Ambient Temp 68F

Solar Heater

Temperature

Solar Temp

In 61F, Out 68F

Solar Temp

In 61F, Out 68F

Pump Status

Speed 2

Pump Status

Speed 2

SERVICESERVICE

Operations and Service Menu

Figure 22. Operation and Service Screen

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

17

12. PROGRAM MENU ( + )

To access the PROGRAM menu, press and hold SERVICE

and MODE keys simultaneously for 7 to 10 seconds until

"Language" screen appears on the display.

This menu allows to change and reset the factory default

settings, as well as providing access to the Installers and

Schedule menus. There are different features and settings

required for different model types. This section outlines

the items noted on the display in Heat Only and Heat/Cool

congurations, the default values and range of adjustable

values and a description of the feature.

Any changes to values are stored into the non-volatile

memory after selection is made using the UP or DOWN

keys. Pressing SERVICE key toggles to the next setting.

Failure to press any key for 5-minutes will cause the screen

to return to Operation mode screen. The Program mode

can also be exited by pressing the MODE key.

CAUTION: Changes to default program congurations

could affect normal functionality of the heater.

Language Selection

The initial display in PROGRAM Menus is "Language"

selection.

The UP and DOWN keys will select English, Spanish or

French language for all menus and Display messages.

Language

English

Lenguaje

Español

Langue

Français

Figure 23. Language Selection Mode

Set Factory Defaults

Press the SERVICE key again. "Set Defaults" option

is displayed. To set factory defaults, press and hold

SERVICE and MODE keys simultaneously for 3 to 5

seconds until "Defaults Set" appears. This operation

resets the operating program to its factory default values.

The pool setpoint is congured to 80°F (27°C), and the

SPA setpoints will default to 100°F (38°C). The maximum

temperature setting for pool and spa is limited to 95°F

(35°C) and 104°F (40°C), respectively. The language

is set to English, and the temperature display is set to

Fahrenheit. The cooling deadband is set to 6°F (3.5°C),

defrost temperature to 24°F (-4°C), defrost deadband

to 10°F (5.5°C) and outside lockout to 45°F (7°C),

respectively. The brownout is set to 230V, and the remote

pool mode is set to Heat. The local schedule is disabled

but not erased, and the "VS Pump Control" and other

add-ons are also disabled. Note that cooling deadband

and remote pool mode settings are only available in Heat/

Cool models.

The "Control Lockout PIN" will be cleared, and the control

will resume normal operation. See the "Control Lockout"

section on page 14.

Brownout Detect.

Set Defaults

Figure 24. Set Defaults Option

Reset Faults

Press the SERVICE key again. "Reset Faults" appears

on the digital display. To clear faults history, press and

hold SERVICE and MODE keys simultaneously for 3 to 5

seconds until "Faults Cleared" appears.

This function clears the historical fault available in

SERVICE menu.

NOTE: When the unit is connected to Wi-Fi, the historical

faults can be accessed in the timeline tab of Raymote.

Reset faults do not affect historical faults registered in

Raymote.

Brownout Detect.

Reset Faults

Figure 25. Reset Faults Option

Wi-Fi Reset

Press the SERVICE key again. "Wi-Fi Reset" appears

on the digital display. To clear stored Wi-Fi signal name

and password, press and hold SERVICE and MODE keys

simultaneously for 3 to 5 seconds until "Wi-Fi Initialized"

appears.

This operation resets the Wi-Fi credentials, leaving the unit

ready to congure connection with the Raymote app. For

details on how to connect your pool heater to Raymote,

follow the instructions on page 43.

Brownout Detect.

WiFi Reset

Figure 26. Wi-Fi Reset Option

Temperature Display

Press the SERVICE key again "Temp Display" appears

on the digital display. The UP or DOWN keys will select

"Fahrenheit" or "Celsius" on the temperature display.

Choose the desired temperature scale. After making

the selection, all temperature screens will be updated to

display degrees in either Fahrenheit or Celsius.

Temp Display

Fahrenheit

Temp Display

Celsius

Figure 27. Temperature Display Option

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

18

Spa Setpoint Maximum Adjustment

Press the SERVICE key again. "Spa Max Temp" appears

on the digital display. Using the UP and DOWN keys will

change the maximum temperature setting to your desired

value. The control can be set to limit the maximum setpoint

in the range of 65°F to 104°F (18°C to 40°C). The default

value is 104°F (40°C).

Spa Max Temp

104F

Figure 28. Spa Setpoint Maximum Adjustment Option

Pool Setpoint Maximum Adjustment

Press the SERVICE key again. "Pool Max Temp" appears

on the digital display. Using the UP and DOWN keys will

change the maximum temperature setting to your desired

value. The control can be set to limit the maximum setpoint

in the range of 65°F to 95°F (18°C to 35°C). The default

value is 95°F (35°C).

Pool Max Temp

95 F

Figure 29. Pool Setpoint Maximum Adjustment Option

Cooling Deadband Adjustment -

(Heat/Cool Models Only)

Press the SERVICE key again. "Cooling Deadband"

appears on the digital display. Using the UP and DOWN

keys will change the cooling deadband setting. In POOL

AUTO mode, the cooling setpoint is the heating setpoint

minus this cooling deadband value. This setting can be set

in the range of 2°F to 10°F degrees (1°C to 5.5°C). The

default value is 6°F (3.5°C).

Cooling Deadband

6 F

Figure 30. Cooling Deadband Adjustment Option

Remote Pool Mode -

(Heat / Cool Models Only)

Press the SERVICE key again. "Remote Pool Mode"

appears on the digital display.

When Remote mode (3-wire selector) is enabled, and

the unit is a Heat/Cool model, this setting can be used to

dene the operation mode of the “Pool” wire selector. Use

UP and DOWN keys to set Remote pool mode to Pool

Heat, Pool Cool or Pool Auto. The default value for remote

pool mode is "Heat".

Remote Pool Mode

Heat

Figure 31. Remote Pool Mode Option

Defrost Temperature Adjustment

To adjust the defrost temperature, press the SERVICE

key and select "Defrost Temp" on the digital display. Use

the UP and DOWN keys to adjust the temperature setting,

which is measured on the coil during defrost mode. The

range of available settings is 20°F to 35°F (-6.5°C to

1.5°C), with a default value of 24°F (-4°C).

Defrost Temp

24F

Figure 32. Defrost Temperature Adjustment Option

Defrost Deadband Adjustment

To adjust the defrost deadband, press the SERVICE key

and select "Defrost Deadband" on the digital display. Use

the UP and DOWN keys to adjust the deadband setting,

which determines when defrost mode ends based on

the coil temperature. The defrost cycle ends when the

coil temperature is higher than the Defrost Temperature

plus the Defrost Deadband. You can set this value in the

range of 5°F to 20°F (2.5°C to 11°C), with a default value

of 10°F (5.5°C).

Defrost Deadband

10F

Figure 33. Defrost Deadband Adjustment Option

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

19

Outside Lockout Temperature

Adjustment

To adjust the outside lockout temperature limit, press

the SERVICE key and select "Outside Lockout" on the

digital display. Use the UP and DOWN keys to set the

ambient temperature at which the unit will be locked out

of operation. This setting can be adjusted in the range of

30°F to 50°F (-1°C to 10°C), with a default value of 45°F

(7°C).

Outside Lockout

45F

Figure 34. Outside Lockout Temperature Adjustment

Brownout Detection Mode

To adjust the brownout detection mode, press the

SERVICE key and navigate to "Brownout Detect" on the

digital display. You can then use the UP and DOWN keys

to choose from three options: 230V, 208V, or Disabled.

Enabling brownout detection will cause the unit to shut

down automatically if the Transformer's 24VAC signal

drops below a certain threshold, specically below

21VAC for 230V or below 24VAC for 208V. This function is

intended to protect the unit from low voltage situations. If

you prefer not to use this feature, simply select “Disabled”.

The default setting for brownout detection is 230V.

Brownout Detect.

230V

Figure 35. Brownout Detection Mode Option

Installer Menu

To access the Installer Menu, press the SERVICE key

and select "INSTALLER Menu" on the digital display. You

can use the UP key to enter the Installer menu, or press

SERVICE to move to the next option. For more details on

the "Installer Menu", please refer to page 21.

INSTALLER Menu

UP key to Enter

Figure 36. Installer Menu Option

Schedule Menu

To access the SCHEDULE Menu, press the SERVICE

key and select "SCHEDULE Menu" on the digital display.

You can use the UP key to enter the Schedule menu and

editor, or press SERVICE to return to the beginning of the

Program menu. For more information on the "Schedule

Menu", please refer to page 25.

SCHEDULE Menu

UP key to Enter

Figure 37. Schedule Menu Option

NOTE: Disabling "Brownout Detection" limits the ability

of the heater to protect the compressor.

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

20

Program Menu Diagram

Figure 38. Program Menu

+

5 sec

PROGRAM Menu

Set Defaults

Reset Faults

Temperature Display

Max Spa Setpoint

Max Pool Setpoint

WiFi Reset

OFF Pool Spa Timed Spa

Operation Mode

MODEMODE

SERVICESERVICE MODEMODE

SERVICESERVICE

+

3 sec

SERVICESERVICE

Defaults SetDefaults Set

Faults ClearedFaults Cleared

Temp Display

Fahrenheit

Temp Display

Fahrenheit

Temp Display

Celsius

Temp Display

Celsius

Spa Max Temp

104 F

Spa Max Temp

104 F

Pool Max Temp

95 F

Pool Max Temp

95 F

WiFi ResetWiFi Reset

WiFi InitializedWiFi Initialized

Reset FaultsReset Faults

Set DefaultsSet DefaultsSet DefaultsSet DefaultsSet Defaults

Language

SERVICESERVICE

Language

English

Language

English

Lenguaje

Español

Lenguaje

Español

Langue

Français

Langue

Français

SERVICESERVICE

Select

Display

Language

UPUP

DOWNDOWN

MODEMODE

SERVICESERVICE

Set Factory

Defaults

+

3 sec

MODEMODE

SERVICESERVICE

Reset Fault

History

+

3 sec

MODEMODE

SERVICESERVICE

Clear Wi-Fi

Configuration

Select

Temperature

Scale

UPUP

DOWNDOWN

Adjust Spa

Temperature

Limit

UPUP

DOWNDOWN

Cooling Deadband

SERVICESERVICE

Cooling Deadband

6 F

Cooling Deadband

6 F

Remote Pool Mode

Heat

Remote Pool Mode

Heat

Select

Remote Pool

Operation

UPUP

DOWNDOWN

SERVICESERVICE

65°F - 104°F

Adjust Spa

Temperature

Limit

UPUP

DOWNDOWN

65°F - 95°F

Adjust

Cooling

Deadband

UPUP

DOWNDOWN

2°F - 10°F

Defrost Temperature

SERVICESERVICE

Defrost Temp

24 F

Defrost Temp

24 F

Adjust

Defrost

Temperature

UPUP

DOWNDOWN

20°F - 35°F

Defrost Deadband

SERVICESERVICE

Defrost Deadband

10 F

Defrost Deadband

10 F

Adjust

Defrost

Deadband

UPUP

DOWNDOWN

5°F - 20°F

Outside Lockout

SERVICESERVICE

Outside Lockout

45 F

Outside Lockout

45 F

Adjust Outside

Lockout Temp.

UPUP

DOWNDOWN

30°F - 50°F

Heat, Cool

or Auto

Brownout Detection

SERVICESERVICE

Brownout Detect.

230V

Brownout Detect.

230V

Select

Brownout

voltage option

UPUP

DOWNDOWN

230v, 208v

or Disabled

Installer Menu

SERVICESERVICE

INSTALLER Menu

UP key to Enter

INSTALLER Menu

UP key to Enter

Press UP key to

enter Installer

Menu

UPUP

Schedule Menu

SERVICESERVICE

SCHEDULE Menu

UP key to Enter

SCHEDULE Menu

UP key to Enter

Press UP key to

enter Schedule

Menu

UPUP

SERVICESERVICE

Options available only in Heat/Cool models

APPROVED

UNCONTROLLED DOCUMENT IF PRINTED

La page est en cours de chargement...

Rheem TWPH-8550EHT10 Le manuel du propriétaire

Ce manuel convient également à

Rheem TWPH-8550EHT10 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents