KitchenAid KSGG700EBS Mode d'emploi

Catégorie
Cuisinières
Taper
Mode d'emploi
THANK YOU for purchasing this high-quality product. Register your range at www.kitchenaid.com. In Canada, register your range
at www.kitchenaid.ca.
For future reference, please make a note of your product model and serial numbers. These can be found on the label located on the oven
frame behind the top-right side of the oven door.
Model Number______________________________________________ Serial Number_______________________________________________
Para una versión de estas instrucciones en español, visite www.kitchenaid.com.
Deberá tener a mano el número de modelo y de serie, que están ubicados en el marco del horno, detrás del lado derecho superior
de la puerta del horno.
Table of Contents
W11397446A
RANGE SAFETY .............................................................................2
The Anti-Tip Bracket ....................................................................3
KEY USAGE TIPS ..........................................................................4
AquaLift
®
Self-Cleaning Technology ...........................................4
Surface Temperatures..................................................................4
Preheating ....................................................................................4
Surface Burners ...........................................................................4
FEATURE GUIDE ...........................................................................5
Electronic Oven Controls .............................................................8
COOKTOP.....................................................................................10
Surface Burners .........................................................................10
Surface Grates ...........................................................................11
Burner Size .................................................................................11
Griddle ........................................................................................12
Cookware ...................................................................................12
Home Canning ...........................................................................13
OVEN .............................................................................................13
Aluminum Foil .............................................................................13
Positioning Racks and Bakeware ..............................................13
Roll-Out Rack .............................................................................14
Oven Vent ...................................................................................14
Sabbath Mode............................................................................15
Baking and Roasting ..................................................................15
Broiling .......................................................................................15
Convection Cooking ..................................................................16
Proong Bread ...........................................................................16
Cook Time ..................................................................................16
Baking Drawer ............................................................................17
Oven Light ..................................................................................17
RANGE CARE ...............................................................................18
Clean Cycle ................................................................................18
General Cleaning ........................................................................19
Remove/Replace Drawer ...........................................................20
TROUBLESHOOTING .................................................................21
ACCESSORIES ............................................................................23
User Guide
Gas Range
2
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
RANGE SAFETY
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
3
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without having
the anti-tip bracket fastened down properly.
Tip Over Hazard
A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:
Slide range forward.
Look for the anti-tip bracket securely attached to floor or wall.
Slide range back so rear range foot is under anti-tip bracket.
See installation instructions for details.
WARNING
Anti-Tip
Bracket
Range Foot
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
WARNING: TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR OR WALL, AND
SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER
ANTI-TIP BRACKET.
WARNING:
NEVER use this appliance as a space
heater to heat or warm the room. Doing so may result in
carbon monoxide poisoning and overheating of the oven.
WARNING: NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through the
oven and may cause carbon monoxide poisoning.
Aluminum foil linings may also trap heat, causing a fire
hazard.
CAUTION: Do not store items of interest to children in
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
Proper Installation – The range, when installed, must be
electrically grounded in accordance with local codes or, in
the absence of local codes, with the
National Electrical
Code, ANSI/NFPA 70
. In Canada, the range must be
electrically grounded in accordance with Canadian
Electrical Code. Be sure the range is properly installed and
grounded by a qualified technician.
This range is equipped with a three-prong grounding plug
for your protection against shock hazard and should be
plugged directly into a properly grounded receptacle. Do
not cut or remove the grounding prong from this plug.
Disconnect power before servicing.
Injuries may result from the misuse of appliance doors or
drawers such as stepping, leaning, or sitting on the doors
or drawers.
Maintenance – Keep range area clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
Top burner flame size should be adjusted so it does not
extend beyond the edge of the cooking utensil.
For self-cleaning ranges
Before Self-Cleaning the Oven Remove broiler pan and
other utensils. Wipe off all excessive spillage before
initiating the cleaning cycle.
4
AquaLift
®
Self-Cleaning Technology
AquaLift
®
Self-Cleaning Technology is a rst-of-its-kind cleaning
solution designed to minimize the time, temperature, and odors
that ordinarily come with traditional self-cleaning methods. With
AquaLift
®
Self-Cleaning Technology, an exclusive coating on the
interior of the oven, is activated with heat and water to release
baked-on soil. To use AquaLift
®
Self-Cleaning Technology, simply
wipe out loose debris, pour water into the oven bottom, and run
the AquaLift
®
Self-Cleaning cycle. When the cycle nishes in under
1 hour at a lower temperature than in traditional self-cleaning
methods, just wipe out the remaining water and loose debris.
See the “Clean Cycle” section for more detailed instructions. For
additional information, frequently asked questions, and videos
on using AquaLift
®
Self-Cleaning Technology, visit our website at
http://whirlpoolcorp.com/aqualift.
Surface Temperatures
When the range is in use, all range surfaces may become hot,
such as the knobs and oven door.
Baking Drawer
When the oven is in use, the drawer may become hot. Do not store
plastics, cloth, or other items that could melt or burn in the drawer.
Oven Vent
The oven vent releases hot air and moisture from the oven and
should not be blocked or covered. Do not set plastics, paper, or
other items that could melt or burn near the oven vent.
Preheating
When beginning a Bake or Convect Bake, the oven will begin
preheating after Start is pressed. The oven will take approximately
12 to 15 minutes to reach 350°F (177°C) with all of the oven
racks provided with your oven inside the oven cavity. Higher
temperatures will take longer to preheat. The preheat cycle rapidly
increases the oven temperature. The actual oven temperature
will go above your set temperature to offset the heat lost when
your oven door is opened to insert food. This ensures that when
you place your food in the oven, the oven will begin at the proper
temperature. Insert your food when the preheat tone sounds. Do
not open the door during preheat before the tone sounds.
Surface Burners
The burner bases and caps must be properly positioned before
cooking. Your range comes with a variety of burner sizes and
caps. Each round burner base is marked with a letter indicating
the burner size. Align the burner bases as shown in the following
illustration:
Align the gas tube opening in the burner base with the orice
holder on the cooktop and the igniter electrode with the notch in
the burner base.
Place the burner caps on the appropriate burner bases. Each
round burner cap is marked with a letter indicating the burner size.
Place the burner caps on the appropriate burner bases.
Burner caps should be level when properly positioned. If burner
caps are not properly positioned, surface burners will not light. The
burner cap should not rock or wobble when properly aligned.
A
D
BE
C
A. Small
(Auxiliary)
B. X-Large
(Stack)
C. Medium
(Semi Rapid)
D. Medium
(Semi Rapid)
E. Large
(Ultra Rapid)
A
B
C
D
E
A. Burner cap
B. Gas tube opening
C. Burner base
D. Igniter electrode
E. Oriceholder
AUX
SR
UR
ST
Small cap
(Auxiliary)
Medium cap
(Semi Rapid)
Large cap
(Ultra Rapid)
X-Large cap
(Stack)
A
B
A. Incorrect
B. Correct
KEY USAGE TIPS
5
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or the Product Help section
of our website at www.kitchenaid.com for more detailed instructions. In Canada, refer to the Product Help Section at www.kitchenaid.ca.
WARNING
Food Poisoning Hazard
Do not let food sit for more than one hour before or
after cooking.
Doing so can result in food poisoning or sickness.
Keypad Feature Instructions
CLOCK/TOOLS Clock The Clock can use a 12 or 24 hour cycle. See the “Electronic Oven Controls” section.
1. Press CLOCK/TOOLS until “CLOCK” is displayed.
2. Use the number keypads to set the time of day.
3. Press START to change the time.
4. Press “3” for AM or “6” for PM.
CLOCK/TOOLS Settings Enables you to personalize the audible tones and oven operation to suit your needs.
Seethe “Electronic Oven Controls” section.
OVEN LIGHT Oven cavity light The oven light is controlled by a keypad on the oven control panel. While the oven
door is closed, press OVEN LIGHT to turn the light On and Off. When the oven door is
opened, the oven light will automatically come On.
TIMER SET/OFF Oven timer The Timer can be set in hours or minutes up to 9 hours and 59 minutes.
1. Press TIMER SET/OFF.
2. Press the number keypads to set the length of time in hr-min-min. Leading zeros
donot have to be entered. For example, for 2 minutes, enter “2.”
3. Press TIMER SET/OFF to begin the countdown. If enabled, end-of-cycle tones will
sound at end of countdown.
4. Press TIMER SET/OFF again to cancel the Timer and return to the time of day.
Donot press the Cancel keypad because the oven will turn off.
5. If the Timer is running but not in the display, press TIMER SET/OFF to display the
countdown for 5 seconds.
START Cooking start The Start keypad begins any oven function. If Start is not pressed within 2 minutes after
pressing a keypad, the function is canceled and the time of day is displayed.
CANCEL UPPER
CANCEL LOWER
(on some models)
Range function The Cancel keypad stops any function for the appropriate oven or drawer, except
the Clock and Timer.
BAKE Baking and
roasting
1. Press BAKE.
2. Set the desired temperature between 170°F and 500°F (75°C and 260°C) using the
number keypads. The default temperature is 350°F (180°C).
3. Press START.
4. To change the temperature, repeat steps 2 and 3.
5. Press CANCEL UPPER when nished.
FEATURE GUIDE
6
Keypad Feature Instructions
STEAM BAKE Steam bake 1. Insert the steam rack with water reservoir in the oven.
2. Pour 1
1
/
2
cups (350 mL) of warm water into the water reservoir.
NOTE: Do not ll past the MAX mark.
3. Press STEAM BAKE.
4. Press the number keypad to select the desired food option.
5. Press the number keypads to set the temperature.
6. Press START.
7. Insert food when preheating nishes.
8. (Optional) Press COOK TIME. Press the number keypads to set the cook time.
9. Press START.
10. Press CANCEL UPPER when nished.
NOTE: Let oven cool before removing and emptying water reservoir.
BROIL Broiling 1. Press BROIL.
2. Press the number keypads to set the desired temperature.
3. Press START and allow the oven to preheat for 2 minutes.
4. To change the temperature, repeat steps 2 and 3.
5. Position the cookware in the oven, and then close the door.
6. Press CANCEL UPPER when nished.
PROOF Proong bread 1. Place prepared dough in oven. Press PROOF.
2. Press START.
Let the dough rise until nearly doubled in size. Proong time may vary depending
on dough type and quantity.
3. Press CANCEL UPPER when nished proong.
Refer to the “Proong Bread” section for more information.
KEEP WARM Hold warm Food must be at serving temperature before placing it in the warmed oven.
1. Press KEEP WARM.
2. Set the desired temperature between 145°F and 190°F (63°C and 88°C) using the
number keypads. The default temperature is 170°F (75°C).
3. Press START.
4. Press CANCEL UPPER when nished.
EASY CONVECT
BAKE
Convection
cooking
1. Press EASY CONVECT BAKE.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 325°F (177°C) in 5°
increments between 170°F and 500°F (77°C and 260°C).
4. Press START.
5. To change the temperature, repeat steps 3 and 4.
6. Press CANCEL UPPER when nished.
EASY CONVECT
BROIL
Convection
cooking
1. Press EASY CONVECT BROIL.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 450°F (232°C) in
5°increments between 300°F and 500°F (149°C and 260°C).
4. Press START.
5. To change the temperature, repeat steps 3 and 4.
6. Press CANCEL UPPER when nished.
7
Keypad Feature Instructions
EASY CONVECT
ROAST
Convection
cooking
1. Press EASY CONVECT ROAST.
2. Press “1” to have the oven automatically convert the temperature and time for
convection baking. Press “2” to manually convert the temperature and time.
3. Press the number keypads to set a temperature other than 325°F (177°C)
in5°increments between 170°F and 500°F (77°C and 260°C).
4. Press START.
5. To change the temperature, repeat steps 3 and 4.
6. Press CANCEL UPPER when nished.
COOK TIME Timed cooking Timed cooking allows the oven to be set to turn on at a certain time of day, cook for
asetlength of time, and/or shut off automatically.
To set a Timed Cook or a Delayed Timed Cook, see the “Cook Time” section.
DELAY START Delayed start The Delay Start keypad is used to enter the starting time for an oven function with
a delayed start. Delay Start should not be used for foods such as breads and cakes
because they may not bake properly.
To set a Timed Cook or a Delayed Timed Cook, see the “Cook Time” section.
BAKING DRAWER
BAKE
(on some models)
Baking drawer 1. Press BAKING DRAWER BAKE.
2. Set the desired temperature between 170°F and 451°F (75°C and 233°C) using the
number keypads. The default temperature is 350°F (180°C).
3. Press START.
4. To change the temperature, repeat steps 2 and 3.
5. Press CANCEL LOWER when nished.
BAKING DRAWER
SLOW COOK
(on some models)
Slow cook
drawer
1. Press BAKING DRAWER SLOW COOK.
2. Set the desired temperature between 190°F and 250°F (88°C and 121°C) using the
number keypads. The default temperature is 190°F (88°C).
3. Place the food(s) in the baking drawer.
4. Press START.
5. (Optional) Set the desired cook time using the number keypads.
6. Press START to begin heating the baking drawer.
7. Press CANCEL LOWER when nished.
BAKING DRAWER
KEEP WARM
(on some models)
Warming drawer Food must be at serving temperature before placing it in the warmed oven.
1. Press BAKING DRAWER KEEP WARM.
2. Set the desired temperature between 145°F and 190°F (63°C and 88°C) using the
number keypads. The default temperature is 170°F (75°C).
3. Press START.
4. Press CANCEL LOWER when nished.
AQUALIFT SELF
CLEAN
Clean cycle See the “Clean Cycle” section.
START
(Hold 3 Sec)
Oven control
lockout
1. Check that the oven is OFF.
2. Press and hold START (Hold 3 Sec) for 3 seconds.
3. A tone will sound, and “Control Locked” will scroll, and then “Locked” will be displayed.
4. Repeat to unlock. No keypads will function with the controls locked. The cooktop
functions are not affected by the oven control lockout.
CLOCK/TOOLS Energy save 1. Press CLOCK/ TOOLS until “ENERGY SAVE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press CANCEL to exit and display the time of day.
If Energy Save is ON, the range will go into Sleep mode after 5 minutes of inactivity.
Any keypad press will activate the display. If Energy Save is OFF, the display will be
ON at all times.
8
Electronic Oven Controls
Control Display
The display will ash when powered up or after a power loss.
Press CANCEL UPPER to clear. When the oven is not in use, the
time of day is displayed. If the range is in Energy Save mode, the
display will be blank when not in use.
Tones
Tones are audible signals, indicating the following:
One Tone
Valid keypad press
Oven is preheated (long tone).
Function has been entered.
Reminder, repeating each minute after the end-of-cycle tones
Three Tones
Invalid keypad press
Four Tones
End-of-cycle
Use the Clock/Tools keypad to change the tone settings.
Energy Save
The Energy Save mode puts the range into Sleep mode and
reduces energy consumption.
To Activate the Energy Save Mode:
1. Press CLOCK/TOOLS until “ENERGY SAVE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press CANCEL to exit and display the time of day.
5. The setting will be activated after 5 minutes.
To Deactivate the Energy Save Mode:
1. Press CLOCK/TOOLS until “ENERGY SAVE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press CANCEL to exit and display the time of day.
5. The clock will reappear in the display and the range can be
operated as usual.
Settings
Many features of the oven control can be adjusted to meet your
personal needs. These changes are made using the Clock/Tools
keypad.
Use the Clock/Tools keypad to scroll through the features that can
be changed. Each press of the Clock/Tools keypad will advance
the display to the next setting. After selecting the feature to be
changed, the control will prompt you for the required input. Then
press START or CANCEL UPPER to exit and display the time
of day. Details of all of the feature changes are explained in the
following sections.
Press CANCEL UPPER to exit Settings.
Clock
The Clock can use a 12 or 24 hour cycle.
1. Press CLOCK/TOOLS until “CLOCK” is displayed.
2. Use the number keypads to set the time of day.
3. Press START to change the time.
4. Press “3” for AM or “6” for PM.
Fahrenheit and Celsius
The temperature is preset to Fahrenheit but can be changed
to Celsius.
1. Press CLOCK/TOOLS until “TEMP UNIT” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Audible Tones Disable
Turns off all tones, including the end-of-cycle tone and keypress
tones. Reminder tones are still active when all tones are disabled.
1. Press CLOCK/TOOLS until “SOUND” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Sound Volume
Sets the volume of the tone to either high or low.
1. Press CLOCK/TOOLS until “SOUND VOLUME” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
End-of-Cycle Tone
Activates or turns off the tones that sound at the end of a cycle.
1. Press CLOCK/TOOLS until “END TONE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Keypress Tones
Activates or turns off the tones when a keypad is pressed.
1. Press CLOCK/TOOLS until “KEYPRESS TONE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Reminder Tones Disable
Turns off the short repeating tone that sounds every 1 minute after
the end-of-cycle tones.
1. Press CLOCK/TOOLS until “REMINDER TONE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
12/24 Hour Clock
1. Press CLOCK/TOOLS until “12/24 HOUR” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
9
Demo Mode
IMPORTANT: This feature is intended for use on the sales oor
with 120 V power connection and permits the control features
to be demonstrated without the oven turning on. If this feature
isactivated, the oven will not work.
1. Press CLOCK/TOOLS until “DEMO MODE” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Sabbath Mode
The Sabbath mode sets the oven to remain ON in a bake setting
until turned off.
When the Sabbath mode is set, only the Bake cycle will operate.
All other cooking and cleaning cycles are disabled. No tones will
sound and the displays will not indicate temperature changes.
When the oven door is opened or closed, the oven light will not
turn on or off and the heating elements will not turn on or off
immediately.
To Enable Sabbath Mode Capability (One Time Only):
1. Press CLOCK/TOOLS until “SABBATH” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
12 Hour Shutoff
The oven control is set to automatically shut off the oven 12 hours
after the oven initiates a cook or clean function. This will not
interfere with any timed or delay cook functions.
1. Press CLOCK/TOOLS until “12Hr AUTO_OFF” is displayed.
2. The current setting will be displayed.
3. Press the “1” keypad to adjust the setting.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Languages - Scrolling Display Text
Language options are English, Spanish, and French.
1. Press CLOCK/TOOLS until “LANGUAGE” is displayed.
2. The current setting will be displayed.
3. Press the “1” or “2” keypad to select the desired language.
4. Press START or CANCEL UPPER to exit and display the
time of day.
Oven Temperature Offset Control
IMPORTANT: Do not use a thermometer to measure oven
temperature. Elements will cycle on and off as needed to provide
consistent temperature but may run slightly hot or cool at any
point in time due to this cycling. Most thermometers are slow
to react to temperature change and will not provide an accurate
reading due to this cycling.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature can
be adjusted to personalize it for your cooking needs. It can be
changed to Fahrenheit or Celsius.
To Adjust Oven Temperature:
1. Press CLOCK/TOOLS until “TEMP CALIB” is displayed.
2. On some models, press “1” to adjust the drawer temperature
calibration. Press START, wait 10 seconds for the display to
change, and then continue with Step 3.
OR
Press START to adjust the oven temperature calibration. Wait
10 seconds for the display to change, and then continue with
Step 3.
3. Press the “3” keypad to increase the temperature in 5°F
(3°C) increments or press the “6” keypad to decrease the
temperature in 5°F (3°C) increments. The offset range is
from -30°F to +30°F (-18°C to +18°C).
4. Press START or CANCEL UPPER to exit and display the
time of day.
10
Electric igniters automatically light the surface burners when
control knobs are turned to .
Before setting a control knob, place lled cookware on the
grate. Do not operate a burner using empty cookware or without
cookware on the grate.
To Set:
1. Push in and turn knob counterclockwise to .
All surface burners will click. Only the burner with the control
knob turned to will produce a ame.
2. Turn knob to anywhere between H (high) and L (low).
Power Failure
In case of prolonged power failure, the surface burners can be
lit manually. Hold a lit match near a burner, and then turn knob
counterclockwise to . After burner lights, turn knob to desired
setting.
Surface Burners
IMPORTANT: Do not obstruct the ow of combustion and
ventilation air around the burner grate edges.
Burner cap: Always keep the burner cap in place when using a
surface burner. A clean burner cap will help avoid poor ignition and
uneven ames. Always clean the burner cap after a spillover, and
routinely remove and clean the caps according to the “General
Cleaning” section.
NOTE: Each round burner base is marked with a letter indicating
the burner size.
Alignment: Be sure to align the gas tube opening in the burner
base with the orice holder on the cooktop and the igniter
electrode with the notch in the burner base.
NOTE: Each round burner base is marked with a letter indicating
the burner size.
Gas Tube Opening: Gas must ow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil,
and do not allow spills, food, cleaning agents or any other material
to enter the gas tube opening. Keep spillovers out of the gas tube
opening by always using a burner cap.
Burner Ports: Check burner ames occasionally for proper size
and shape as shown in the previous illustration. A good ame is
blue in color, not yellow. Keep this area free of soil, and do not
allow spills, food, cleaning agents or any other material to enter
the burner ports.
To Clean:
IMPORTANT: Before cleaning, make sure all controls are off and
the cooktop is cool. Do not use oven cleaners, bleach or rust
removers. Do not wash in the dishwasher.
1. Remove the burner cap and the burner base and clean
according to the “General Cleaning” section.
2. Clean the gas tube opening with a damp cloth.
3. Clean clogged burner ports with a straight pin as shown. Do
not enlarge or distort the port. Do not use a wooden toothpick.
If the burner needs to be adjusted, contact a trained repair
specialist.
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
REMEMBER: When range is in use, the entire cooktop area
may become hot.
A
B
C
D
E
A. Burner cap
B. Gas tube opening
C. Burner base
D. Igniter electrode
E. Oriceholder
B
A
A. 1 to 1
1
/
2
" (2.5 to 3.8 cm)
B. Burner ports
COOKTOP
11
4. Replace the burner base. Each round burner base is marked
with a letter indicating the burner size. See the following
illustration for burner positions:
5. Replace the burner cap, making sure it is properly aligned with
the burner base. The burner cap should not rock or wobble
when properly aligned.
IMPORTANT: The bottom of the small and medium caps are
different. Do not put the wrong size burner cap on the burner
base.
NOTE: Each round burner base is marked with a letter indicating
the burner size.
AUX
SR
UR
ST
Small cap
(Auxiliary)
Medium cap
(Semi Rapid)
Large cap
(Ultra Rapid)
X-Large cap
(Stack)
6. Turn on the burner. If the burner does not light, check cap
alignment. If the burner still does not light, turn off the burner.
Do not service the burner yourself. Contact a trained repair
specialist.
Surface Grates
The grates must be properly positioned before cooking. In the
proper position, the grates should be ush and level. Improper
installation of the grates may result in chipping or scratching of the
cooktop.
To ensure proper positioning, align bumpers on grate bottom with
the indentations in the cooktop.
A
D
C
BE
A
B
A. Incorrect
B. Correct
A
A
B
A. Bumpers
B. Alignment indentations
The surface grates interlock using the hook on one end of the
grate and the indent on the other. To remove the grates, lift the
rearof the left grate off the hook, and then lift the front of the right
grate off the hook and pull apart. To replace the grates, replace
theleft grate rst. Place the front indent of the right grate over the
hook of the left grate, and then lift the rear of the left grate and
place the indent over the hook on the right grate.
Although the burner grates are durable, they will gradually lose
their shine and/or discolor due to the high temperatures of the
gasame.
Burner Size
Select a burner that best ts your cookware. See the following
illustration and chart.
Burner Size Recommended Use
Small (Auxiliary) Low-heat cooking
Melting chocolate or butter
Medium (Semi Rapid) Multipurpose burner
Large (Ultra Rapid) For large cookware
Stack (most powerful) For large cookware
Most powerful burner
A
B
A. Hook
B. Indent
ST
(most
powerful)
OV
AUX
SR
UR
SR
A. Small
(Auxiliary)
B. X-Large
(Stack)
C. Medium
(Semi Rapid)
D. Medium
(Semi Rapid)
E. Large
(Ultra Rapid)
12
Griddle
To Use the Griddle:
1. Locate the griddle on the right side grate, as shown. The
locating feet on the bottom of the griddle will engage the grate
tines to keep the griddle from sliding.
2. Before each use, brush on a thin layer of cooking oil to keep
food from sticking. Cooking sprays may leave a sticky residue
on the griddle that is hard to remove.
3. Preheat the griddle for 5 minutes. Preheating the griddle slowly
will ensure even heat distribution and will avoid warping the
griddle.
4. For preheating and cooking, set the front burner to the lowest
heat setting and the rear burner to medium-high heat for best
performance.
NOTE: The griddle may also be used on the left side grate. For
best results, the rear burner setting should be set to Medium-
Low or Medium, and the front burner setting should be set to
Low.
To Clean the Griddle:
1. Let the griddle cool, and then empty the drip tray.
2. See the “General Cleaning” section for cleaning instructions.
3. Store griddle in a cool dry place.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a at bottom, straight sides and a
well-tting lid, and the material should be of medium-to-heavy
thickness.
Rough nishes may scratch the cooktop or coils. Aluminum and
copper may be used as a core or base in cookware. However,
when used as a base they can leave permanent marks on the
surfaces.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick nish has the
same characteristics as its base material. For example, aluminum
cookware with a nonstick nish will take on the properties of
aluminum.
Cookware with nonstick surfaces should not be used under the
broiler.
Check for atness by placing the straight edge of a ruler across
the bottom of the cookware. While you rotate the ruler, no space
or light should be visible between it and the cookware.
Griddleinstalledonrightsideofcooktop
Use the following chart as a guide for cookware material
characteristics.
Cookware Characteristics
Aluminum Heats quickly and evenly.
Suitable for all types of cooking.
Medium or heavy thickness is best for most
cooking tasks.
May leave aluminum residues, which may
be diminished if cleaned immediately after
cooking.
Cast iron Heats slowly and evenly.
Good for browning and frying.
Maintains heat for slow cooking.
Rough edges or burrs may scratch the
cooktop.
Ceramic
or Ceramic
glass
Follow manufacturer’s instructions.
Heats slowly, but unevenly.
Ideal results on low to medium heat
settings.
May scratch the cooktop.
Copper Heats very quickly and evenly.
May leave copper residues, which may be
diminished if cleaned immediately after
cooking.
Can leave a permanent stain or bond to the
cooktop if overheated.
Earthenware Follow manufacturer’s instructions.
Use on low heat settings.
May scratch the cooktop.
Porcelain
enamel-on-
steel or cast
iron
See stainless steel or cast iron.
Porcelain enamel bakeware without the
metal base may bond to the cooktop if
overheated.
Stainless
steel
Heats quickly, but unevenly.
A core or base of aluminum or copper on
stainless steel provides even heating.
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2 0
1
2
3
4
5
6
7
13
Use at-bottomed cookware for best cooking results and energy
efciency. The cookware should be about the same size as the
cooking area outlined on the cooktop. Cookware should not
extend more than 1/2" (1.3 cm) outside the area.
Home Canning
When canning for long periods, alternate the use of surface
burners between batches. This allows time for the most recently
used areas to cool.
Center the canner on the grate above the burner.
Do not place canner on 2 surface burners at the same time.
For more information, contact your local agricultural extension
ofce, or refer to published home canning guides. Companies
that manufacture home canning products can also offer
assistance.
Odors and smoke are normal when the oven is used the rst few
times or when it is heavily soiled.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off by the oven. Exposure to the fumes may result
in death to certain birds. Always move birds to another closed and
well-ventilated room.
Aluminum Foil
IMPORTANT: To avoid permanent damage to the oven bottom
nish, do not line the oven bottom with any type of foil or liner.
For best cooking results, do not cover entire oven rack with foil
because air must be able to move freely.
Positioning Racks and Bakeware
IMPORTANT: To avoid permanent damage to the porcelain
nish, do not place food or bakeware directly on the oven door
or bottom.
Bakeware
To cook food evenly, hot air must be able to circulate. Allow
2" (5 cm) of space around bakeware and oven walls. Make sure
that no bakeware piece is directly over another.
Racks
Position racks before turning on the oven.
Do not position racks with bakeware on them.
Make sure racks are level.
To position a rack, pull it out to the stop position, raise the front
edge, and then lift out. Use the following illustration and charts
as guides.
The oven has 7 positions for a at rack, as shown in the previous
illustration and the following table.
Flat Rack Position* Type of Food
7 Broiling/searing meats, hamburgers,
steaks
6 Broiled meats, poultry, sh
3 or 4 Most baked goods, casseroles,
frozen foods
2 Roasted meats
1 Large roasts or poultry
7
6
5
4
3
2
1
For hamburger patties to have a well-seared exterior and a rare
interior, use a at rack in rack position 7. Side 1 should cook
for approximately 2
1
/
2
to 3
1
/
2
minutes. Side 2 should cook for
approximately 4 to 5 minutes. Expect a moderate degree of smoke
when broiling.
* If your model has a Max Capacity Oven Rack, the recessed
ends must be placed in the rack position above the desired
position of the food. See the following illustration.
IMPORTANT: These rack positions are for at racks. If a Max
Capacity Oven Rack is used, the rack position must be adjusted
as shown in the previous gure.
Multiple Rack Cooking
2-rack (non-convection): Use rack positions 2 and 5 or 3 and 6.
2-rack (convection): Use rack positions 2 and 5 or 3 and 6.
3-rack (convection): Use rack positions 2 and 7 and a Max
Capacity Oven Rack in rack position 5.
Baking Cookies and Layer Cakes on 2 Racks
Baking Layer Cakes
For best results when baking cakes on 2 racks, use the
Convection Bake function, a at rack in rack position 2 and a Max
Capacity Oven rack in rack position 6. If you do not have a Max
Capacity Oven Rack, use a at rack in rack position 5. Place the
cakes on the racks as shown. Keep at least 3" (7.6 cm) of space
between the front of the racks and the front cakes.
A. Endsofrackinposition3
B. Food in position 2
OVEN
14
Baking Cookies
For best results when baking cookies on 2 racks, use the
Convection Bake function, a at rack in rack position 2 and a Max
Capacity Oven rack in rack position 6 or a at rack in position 5.
Roll-Out Rack
The roll-out rack allows easy access to position and remove food
in the oven. It is not recommended to use the roll-out rack in the
top rack, position 7, or the bottom rack, position 1.
Open Position
Closed and Engaged Position
To Insert Roll-Out Rack
1. Angle the front of the rack assembly up, and then insert
the rack frame into the “V” cutout in the rack guides of the
oven cavity.
2. Keep rack assembly lifted up at an angle, and then push
in to bypass the lower “V” cutout.
3. Lower the front of the rack assembly, and then gently slide
rack assembly into oven, bypassing the “V” cutouts. Push the
rack assembly into the oven until it stops at the ladder in the
back of the oven.
4. Reach through the rack to hold the sliding rack and the front
crossbar. Lift the front of the rack assembly, and then push the
rack assembly to the back of the oven. Lower the front of the
rack assembly so the ladder hook engages with the ladder on
both sides of the oven.
To Remove Roll-Out Rack
1. Push the sliding rack in completely so that it is in the closed
and engaged position.
2. Reach through the rack to hold the sliding rack and the front
crossbar. Lift the front of the rack assembly to disengage the
ladder hook from the ladders at the rear of the oven, and then
pull the rack assembly forward.
3. Using 2 hands, gently pull the sliding rack and the rack frame
at the same time to the “V” cutout. Angle the rack so that the
front is higher than the back, and then gently pull rack past
“V” cutout and then out of the oven.
To avoid damage to the sliding rack, do not place more than
25lbs(11.4 kg) on the rack.
Do not clean the roll-out rack in a dishwasher. It may remove the
rack’s lubricant and affect its ability to slide.
See the “General Cleaning” section for more information.
Oven Vent
The oven vent releases hot air and moisture from the oven and
should not be blocked or covered. Blocking or covering the vent
will cause poor air circulation, affecting cooking and cleaning
results. Do not set plastics, paper, or other items that could melt
or burn near the oven vent.
A
B
A. Rackframe
B. Sliding rack
A
B
A. Rackframe
B. Sliding rack
A
B
A. “V” cutout
B. Rack guides
A
B
C
D
A. “V” cutout
B. Rack guides
C.Ladderhook
D. Ladder
A
B
A. Sliding rack
B. Front crossbar
A
A. Oven vent
15
Sabbath Mode
The Sabbath mode sets the oven to remain on in a bake setting
until turned off.
When the Sabbath mode is set, only the Bake cycle will operate.
All other cooking and cleaning cycles are disabled. No tones will
sound and the displays will not indicate temperature changes.
When the oven door is opened or closed, the oven light will not
turn on or off and the heating elements will not turn on or off
immediately.
To Enable Sabbath Mode Capability (One Time Only):
1. Press CLOCK/TOOLS until “SABBATH” is displayed.
“OFF. Press (1) for On” will scroll in the display.
NOTE: A bake function for either, or both, ovens must be
started before Sabbath Mode can be activated.
2. Press the “1” keypad. “ON. Press (1) for Off” will scroll in the
display. Sabbath mode can be activated for baking.
3. Press START or CANCEL UPPER to exit and display the time
of day.
NOTE: To disable the Sabbath mode, repeat steps 1 through 3
to change the status from “SABBATH ON” to “SABBATH OFF.”
To Activate Sabbath Mode:
1. Press BAKE for the desired oven.
2. Press the number keypad to set a temperature other than
350°F (177°C).
3. Press START.
For timed cooking in Sabbath mode, press COOK TIME and
then the number keypads to set the desired cook time.
4. Press CLOCK/TOOLS. Three tones will sound. Then press “7.”
“SAb” will appear in the display.
To Adjust Temperature (When Sabbath Mode Is Running):
1. Press the number keypad as instructed by the scrolling text
to select the new temperature.
NOTE: The temperature adjustment will not appear on the
display. The scrolling text will be shown on the display as it
was before the keypad was pressed.
2. Press START.
To Deactivate Sabbath Mode:
Press CLOCK/TOOLS, and then press “7” to return to regular
baking, or press CANCEL for the desired oven to turn off
the range.
NOTE: No tones will sound while deactivating Sabbath mode.
Baking and Roasting
Preheating
When beginning a Bake or Convect Roast cycle, the oven
will begin preheating after Start is pressed. The oven will take
approximately 12 to 15 minutes to reach 350°F (177°C) with all
of the oven racks provided with your oven inside the oven cavity.
Higher temperatures will take longer to preheat. The preheat
cycle rapidly increases the oven temperature. The actual oven
temperature will go above your set temperature to offset the heat
lost when your oven door is opened to insert food. This ensures
that when you place your food in the oven, the oven will begin at
the proper temperature. Insert your food when the preheat tone
sounds. Do not open the door during preheat before the tone
sounds.
Oven Temperature
While in use, the oven elements will cycle on and off as needed
to maintain a consistent temperature, but they may run slightly
hot or cool at any point in time due to this cycling. Opening the
oven door while in use will release the hot air and cool the oven
which could impact the cooking time and performance. It is
recommended to use the oven light to monitor cooking progress.
NOTE: On models with convection, the convection fan may run in
the non-convection Bake mode to improve oven performance.
Temperature Management System
The Temperature Management System electronically regulates the
oven heat levels during preheat and Bake to maintain a precise
temperature range for optimal cooking results. The bake and broil
elements or burners cycle on and off in intervals. On convection
range models, the fan will run while preheating and may be cycled
on and off for short intervals during Bake to provide the best
results. This feature is automatically activated when the oven is
in use.
Before baking and roasting, position racks according to the
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven preheat cycle to end before
putting food in, unless it is recommended in the recipe.
Steam Bake
The Steam Bake function works in conjunction with the steam
rack to provide additional moisture during baking. The steam rack
contains a water reservoir which heats up and releases steam
into the oven cavity during the Steam Bake cycle. There are
3preprogrammed food options to choose from: Breads, Desserts,
and Fish as well as a Refresh/Reheat option.
For best performance, place the steam rack in the lowest available
rack position in the cavity and pour 1
1
/
2
cups (350 mL) of water
into the reservoir. Do not ll past the MAX level indicated on
the reservoir.
After the Steam Bake cycle is complete, some water may remain
in the reservoir. This is normal. Wait for the oven to cool and
discard the water.
Broiling
When broiling, preheat the oven for 2 minutes before putting
food in, unless recommended otherwise in the recipe. Position
food on grid in a broiler pan, and then place it in the center
of the oven rack.
IMPORTANT: Close the door to ensure proper broiling
temperature.
Changing the temperature when broiling allows more precise
control when cooking. The lower the broil setting is, the slower
the cooking. Thicker cuts and unevenly shaped pieces of meat,
sh, and poultry may cook better at lower broil settings. Use rack
6 or 7 for broiling. Refer to the “Positioning Racks and Bakeware”
section for more information.
On lower settings, the broil element will cycle on and off to
maintain the proper temperature.
For best results, use a broiler pan and grid. It is designed
to drain juices and help avoid spatter and smoke.
If you would like to purchase a broiler pan, one may be
ordered. See the “Accessories” section.
A
B
A. Steam rack
B. Water reservoir
16
Convection Cooking
In a convection oven, the fan-circulated hot air continually
distributes heat more evenly than the natural movement of air in a
standard thermal oven. This movement of hot air helps maintain a
consistent temperature throughout the oven, cooking foods more
evenly, crisping surfaces while sealing in moisture, and yielding
crustier breads.
During convection baking or roasting, the bake, broil, and
convection elements cycle on and off in intervals while the fan
circulates the hot air. During convection broiling, the broil and
convection elements cycle on and off.
If the oven door is opened during convection cooking, the fan
will turn off immediately. It will come back on when the oven
door is closed.
With convection cooking, most foods can be cooked at a lower
temperature and/or a shorter cooking time than in a standard
thermal oven. Depending upon the selected cooking mode,
EasyConvect™ conversion can automatically reduce the standard
recipe temperature and/or time you input for convection cooking.
If you choose not to use the EasyConvect™ conversion, use the
following table as a guide.
Convection Mode Time/Temperature Guidelines
Convection Bake 25°F (15°C) lower temperature,
possible shortened cooking time
Convection Roast Cooking time shortened by up to 30%
Convection Broil Shortened cooking time
Convect Options
Convect Bake - multiple-rack baking or cookies, biscuits, breads,
casseroles, tarts, tortes, cakes
Convect Roast - whole chicken or turkey, vegetables, pork roasts,
beef roasts
Convect Broil - thicker cuts or unevenly shaped pieces of meat,
sh, or poultry
Proong Bread
Proong bread prepares the dough for baking by activating
the yeast. Follow the recipe directions as a guide. Proof should
be used for fresh dough, thawed dough, and for the rst and
second rise.
To Proof:
Before rst proong, place the dough in a lightly greased bowl and
cover loosely with wax paper, coated with shortening. Place on
rack guide 2 and close the oven door.
NOTE: If the temperature of the oven is greater than 120°F (49°C),
“Oven Cooling” will be displayed until the temperature is less than
120°F (49°C).
1. Press PROOF.
2. Press START.
Let the dough rise until nearly doubled in size. Proong time
may vary depending on dough type and quantity.
3. Press CANCEL UPPER when nished proong.
Before second proong, shape the dough, place it in baking
pan(s), and cover loosely. Follow the same placement and
control steps above. Before baking, remove the cover.
NOTE: If the oven temperature is greater than 120°F (49°C),
thedisplay will indicate “Oven Cooling” until the temperature
isbelow 120°F (49°C).
Cook Time
To Set a Timed Cook:
1. Press BAKE or BROIL or press an Easy Convect function.
2. Press the number keypads to enter a temperature other than
the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light will
light up.
4. Press the number keypads to enter the length of time to cook.
5. Press START. The display will count down the time. When the
time ends, the oven will shut off automatically.
6. Press CANCEL for the desired oven to clear the display.
To Set a Delayed Timed Cook:
1. Press BAKE or BROIL or press an Easy Convect function.
2. Press the number keypads to enter a temperature other than
the one displayed.
3. Press COOK TIME. The Cook Time oven indicator light will
light up.
4. Press number keypads to enter the length of time to cook.
5. Press DELAY START.
6. Press number keypads to enter the number of hours and/or
minutes you want to delay the start time.
7. Press START.
When the start time is reached, the oven will automatically turn
on. The temperature and/or time settings can be changed anytime
after the oven turns on by repeating steps 2 through 4. When the
set cook time ends, the oven will shut off automatically.
8. Press CANCEL for the desired oven to clear the display.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
17
Baking Drawer
The baking drawer is highly recommended for baking frozen
foods. Use the temperature and medium cook time given on
the frozen food packaging. For example, if the packaging
suggests a cook time of 15 to 20 minutes, set the cook time
for 17 minutes. Check food for doneness before removing
from the baking drawer.
The baking drawer may also be used for conventional baking,
slow cooking, and keeping hot cooked foods warm. It is not
recommended to prepare foods taller than the height of the baking
drawer rack handles or foods that may rise above 2
1
/
2
" (6.4 cm)
in the baking drawer.
IMPORTANT: Always use the baking drawer rack when using the
baking drawer.
See the “General Cleaning” section for more information.
WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
A
B
C
A. Baking drawer
B. Baking drawer rack
C.Bakingdrawerrackhandles
To Bake with the Baking Drawer:
1. Press BAKING DRAWER BAKE.
2. Set the desired temperature between 170°F and
451°F(75°Cand 233°C) using the number keypads. The
default temperature is 350°F (180°C).
3. Press START.
4. To change the temperature, repeat steps 2 and 3.
5. Press CANCEL LOWER when nished.
6. Remove food from the drawer.
To Slow Cook with the Baking Drawer:
IMPORTANT: Brown roasts thoroughly before starting to
slow cook.
1. Place food in the Baking Drawer.
2. Press BAKING DRAWER SLOW COOK.
3. Set the desired temperature between 190°F and
250°F (88°C and 190°C) using the number keypads. The
default temperature is 190°F (88°C).
4. Press START.
5. (Optional) Set the desired cook time using the number
keypads.
6. Press START.
7. Press CANCEL LOWER when nished.
8. Remove food from the baking drawer.
To Keep Warm with the Baking Drawer:
Food must be at serving temperature before placing it in the
warmed drawer.
1. Place food in the baking drawer.
2. Press BAKING DRAWER KEEP WARM.
3. Set the desired temperature between 190°F and 250°F
(88°C and 121°C) using the number keypads. The default
temperature is 190°F (88°C).
4. Press START.
5. Press CANCEL LOWER when nished.
6. Remove food from the baking drawer.
Oven Light
The oven light is a standard 40 W appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the Off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb by turning clockwise.
5. Replace bulb cover by turning clockwise.
6. Plug in range or reconnect power.
18
RANGE CARE
Clean Cycle
AquaLift
®
Technology is an innovative cleaning solution that
utilizes heat and water to release baked-on spills from the oven in
less than 1 hour. This new cleaning technology is a low-heat, odor-
free alternative to traditional Clean options.
Allow the oven to cool to room temperature before using the Clean
cycle. If your oven cavity is above 200°F (93°C), “Oven Cooling”
will appear in the display and the Clean cycle will not be activated
until the oven cavity cools down.
To Clean:
1. Remove all racks and accessories from the oven cavity and
wipe excess soil. Use a plastic scraper to remove easily
removed soils.
2. Pour 1
3
/
4
cups (14 oz [414 mL]) of distilled or ltered water
onto the bottom of the empty oven and close the oven door.
IMPORTANT: Do not use chemicals or other additives with the
water. Do not open the oven door during the Clean cycle. The
water on the oven bottom is hot.
3. Press AQUALIFT SELF CLEAN and then START on the oven
control panel.
4. Allow 40 minutes for cleaning and cooldown. A beep will
sound when the Clean cycle is complete.
5. Press CANCEL UPPER at the end of the cycle. Cancel Upper
may be pressed at any time to stop the Clean cycle.
6. Remove the residual water and loosened soils with a sponge
or cloth immediately after the Clean cycle is complete. Much
of the initial 13/4 cups (14 oz [414 mL]) of water will remain in
the oven after the cycle is completed. If additional soils remain,
leave a small amount of water in the oven bottom to assist
with the cleaning.
7. If any soils remain, remove them with a non-scratch scrubbing
sponge or plastic scraper. Additional Clean cycles may be run
to help remove the stubborn soils.
IMPORTANT: Do not use oven cleaners. The use of
chemicals, including commercial oven cleaners or metal
scouring pads, may cause permanent damage to the porcelain
surface of the oven interior.
NOTES:
The range should be level to ensure that the entire surface
of the bottom of the oven cavity is covered by water at the
beginning of the Clean cycle.
For best results, use distilled or ltered water. Tap water may
leave mineral deposits on the oven bottom.
Before removing the residual water and loosened soils at the
end of the Clean cycle, insert a cloth or paper towel between
the lower edge of the oven door and the front frame to keep
water from spilling onto the front of the range and the oor.
Soil baked on through several cooking cycles will be more
difcult to remove with the Clean cycle.
Nonabrasive scrub sponges or eraser-style cleaning pads
(without cleaners) can be effective for cleaning the oven cavity
walls, oven door, and oven bottom for difcult soils. For best
results, moisten the pads and sponges before use.
Run an additional Clean cycle for stubborn soils.
Affresh
®
Kitchen Appliance Cleaner and affresh
®
Cooktop
Cleaner may be used to clean the oven bottom, walls, and
door when the oven has nished the cycle and returned to
room temperature. If affresh
®
Cooktop Cleaner is used, it is
recommended to wipe out the cavity with distilled water as
well. Refer to the “Accessories” section for information on
ordering.
Additional AquaLift
®
Technology Cleaning Kits may be
obtained by ordering Part Number W10423113RP. See the
“Accessories” section for more information.
For assistance with AquaLift
®
Technology, call 1-877-258-0808
in the U.S.A. or 1-800-807-6777 in Canada, or visit our website
at http://whirlpoolcorp.com/aqualift.
19
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are OFF and
the oven and cooktop are cool. Always follow label instructions
on cleaning products. For additional information, you can visit our
website at www.kitchenaid.com. In Canada, visit our website at
www.kitchenaid.ca.
Soap, water, and a soft cloth or sponge are suggested rst, unless
otherwise noted.
EXTERIOR PORCELAIN ENAMEL SURFACES
(on some models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire range is cool. These spills may
affect the nish.
Cleaning Method:
Glass cleaner, mild liquid cleaner, or nonabrasive
scrubbing pad:
Gently clean around the model/serial/rating plate because
scrubbing may remove numbers.
Affresh
®
Kitchen and Appliance Cleaner Part Number
W10355010 (not included):
See the “Accessories” section for more information.
STAINLESS STEEL (on some models)
NOTE: To avoid damage to stainless steel surfaces, do not use
soap-lled scouring pads, abrasive cleaners, Cooktop Cleaner,
steel-wool pads, gritty washcloths, or abrasive paper towels.
Damage may occur to stainless steel surfaces, even with one-time
or limited use.
Cleaning Method:
Rub in direction of grain to avoid damaging.
Affresh
®
Stainless Steel Cleaner Part Number W10355016 (not
included):
See the “Accessories” section for more information.
Yellow Heat Stains:
1. Add 1 tbs (15 mL) of table salt to 1/4 cup (59.1 mL) of vinegar,
and then stir for 1 minute. Not all of the salt will dissolve.
2. Using a soft cloth, soak up the liquid of the vinegar mixture.
Dab the wet cloth onto the yellow stains for 3 to 4 minutes.
The wetter the stainless steel is, the better the cleaning results
will be.
3. Let sit until the yellow stains have faded. Using a dry soft cloth,
wipe off the remaining vinegar mixture.
4. Repeat steps 1 to 3 until all yellow stains have been removed.
5. Using clean water and a fresh soft cloth, clean off any
remaining residue. Dry with a clean soft cloth.
6. Use affresh
®
Stainless Steel Cleaner Part Number W10355016
(not included) to protect and polish the cleaned surface.
NOTE: Remove surface grates before cleaning rear vent trim.
Avoid dripping the vinegar mixture into the vent holes or down the
back of the range.
METALLIC PAINT (on some models)
Do not use abrasive cleaners, cleaners with bleach, rust removers,
ammonia or sodium hydroxide (lye) because paint surface may
stain.
PORCELAIN-COATED GRATES AND CAPS
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the cooktop, grates and caps are cool.
These spills may affect the nish.
To avoid chipping, do not bang grates, and caps against each
other or hard surfaces such as cast iron cookware.
Do not reassemble caps on burners while wet.
Cleaning Method:
Nonabrasive plastic scrubbing pad and mildly abrasive
cleanser:
Clean as soon as cooktop, grates, and caps are cool.
Dishwasher (grates only, not caps):
Use the most-aggressive cycle. Cooked-on soils should be
soaked or scrubbed before going into a dishwasher.
Although the burner grates are durable, they may lose their
shine and/or discolor when washed in a dishwasher.
Gas Grate and Drip Pan Cleaner Part Number 31617 (not
included):
See the “Accessories” section for more information.
SURFACE BURNERS
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the cooktop, grates, and caps are cool.
These spills may affect the nish.
To avoid chipping, do not bang grates and caps against each
other or hard surfaces such as cast iron cookware.
Do not reassemble caps on burners while wet.
Do not clean in the Self-Cleaning cycle.
Do not clean in dishwasher.
Cleaning Method:
Nonabrasive plastic scrubbing pad and mildly abrasive
cleanser:
Clean as soon as cooktop, grates, burners, and caps are cool.
Gas Grate and Drip Pan Cleaner (not included).
COOKTOP CONTROLS
To avoid damage to the cooktop controls, do not use steel wool,
abrasive cleansers, or oven cleaner.
To avoid damage, do not soak knobs. When replacing knobs,
make sure knobs are in the Off position.
On some models, do not remove seals under knobs.
Cleaning Method:
Soap and water:
Pull knobs straight away from control panel to remove.
GRIDDLE
To avoid damaging the nonstick surface, do not use steel wool or
abrasive cleaners.
Cleaning Method:
Mild detergent
Dishwasher:
Although the griddle is durable, it may lose its shine and/or is
color when washed in a dishwasher.
20
CONTROL PANEL AND OVEN DOOR EXTERIOR
To avoid damage to the control panel, do not use abrasive
cleaners, steel-wool pads, gritty washcloths or abrasive paper
towels.
Cleaning Method:
Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
Affresh
®
Kitchen and Appliance Cleaner Part Number
W10355010 (not included):
See the “Accessories” section for more information.
OVEN RACKS
Cleaning Method:
Steel-wool pad
For racks that have discolored and are harder to slide, a light
coating of vegetable oil applied to the rack guides will help
them slide.
Dishwasher (steam rack water reservoir only, not racks):
Although the water reservoir is durable, it may lose its shine
and/or discolor when washed in a dishwasher.
BAKING DRAWER
Check that baking drawer is cool and empty before cleaning.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain. Staining, etching,
pitting, or faint white spots can result.
Cleaning Method:
Mild detergent
OVEN CAVITY
Use AquaLift
®
Technology regularly to clean oven spills.
Do not use oven cleaners.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain. Staining, etching,
pitting, or faint white spots can result.
Cleaning Method:
Self-Cleaning cycle:
See the “Clean Cycle” section rst.
Remove/Replace Drawer
Remove all items from inside the baking drawer, and then allow
the range to cool completely before attempting to remove the
drawer.
To Remove:
1. Open the drawer to its fully open position.
2. Using a at-blade screwdriver, gently loosen the drawer
from the glide alignment notch, and then lift up the drawer
alignment tab from the glide.
3. Repeat Step 2 on the other side. The drawer is no longer
attached to the drawer glides. Using both hands, pick up
thedrawer to complete the removal.
To Replace:
1. Align the forward drawer notches with the notches in the
drawer glides on both sides. Place the rear alignment tabs
into the drawer glides on both sides.
2. Push the drawer in all the way.
3. Gently open and close the drawer to ensure it is seated
properly on the glides on both sides.
A
B
C
A. Flat-blade screwdriver
B. Drawer alignment tab
C.Drawerglidenotch
A
B
A. Drawer alignment tab
B. Drawerglidenotch
1 / 1

KitchenAid KSGG700EBS Mode d'emploi

Catégorie
Cuisinières
Taper
Mode d'emploi

dans d''autres langues