Alpine SPX-Z18M Le manuel du propriétaire

Marque: Alpine

Modèle: SPX-Z18M

Catégorie: Haut-parleurs de voiture

Taper: Le manuel du propriétaire

English/Français

Points to Observe for Safe Usage

• Read this manual carefully before starting operation and

use this system safely. We cannot be responsible for

problems resulting from failure to observe the instructions

in this manual.

• This manual uses various pictorial displays to show how to

use this product safely and to avoid harm to yourself and

others and damage to your property. Here is what these

pictorial displays mean. Understanding them is important

for reading this manual.

• Meaning of displays

Points à respecter pour une utilisation sûre

•

Lire attentivement ce manuel avant de commencer l’opération

et l’utilisation du système en toute sécurité. Nous dégageons

toute responsabilité des problèmes résultant du non-respect

des instructions décrites dans ce manuel.

•

Ce manuel utilise divers affichages illustrés pour montrer comment utiliser

cet appareil en toute sécurité, pour éviter de s’exposer soi-même et les

autres personnes aux dangers et pour éviter d’endommager l’appareil.

Voici la signification de ces affichages illustrés. Il est important de bien les

comprendre pour la lecture de ce manuel.

• Signification des affichages

Avertissement

NE PAS DESASSEMBLER NI MODIFIER L’APPAREIL. Il y a risque

d’accident, d’incendie ou de choc électrique.

GARDER LES PETITS OBJETS COMME LES PILES HORS DE PORTEE DES

ENFANTS. L’ingestion de tels objets peut entraîner de graves blessures.

En cas d’ingestion, consulter immédiatement un médecin.

NE PAS INSTALLER A DES ENDROITS SUSCEPTIBLES D’ENTRAVER

LA CONDUITE DU VEHICULE, COMME LE VOLANT OU LE LEVIER DE

VITESSES. La vue vers l’avant pourrait être obstruée ou les

mouvements gênés, etc., et provoquer un accident grave.

NE PAS ENDOMMAGER DE CONDUITES NI DE CABLES LORS DU

FORAGE DES TROUS. Lors du forage de trous dans le châssis en

vue de l’installation, veiller à ne pas entrer en contact,

endommager ni obstruer de conduites, de tuyaux à carburant

ou de fils électriques. Le non-respect de cette précaution peut

entraîner un incendie.

NE PAS UTILISER DES ECROUS NI DES BOULONS DU CIRCUIT DE FREINAGE OU

DE DIRECTION POUR LES CONNEXIONS DE MASSE. Les boulons et les écrous

utilisés pour les circuits de freinage et de direction (ou de tout autre système

de sécurité) ou les réservoirs ne peuvent JAMAIS être utilisés pour

l’installation ou la liaison à la masse. L’utilisation de ces organes peut

désactiver le système de contrôle du véhicule et causer un incendie, etc.

NE PAS INSTALLER LE MONITEUR PRES DU COUSSIN D’AIR DU

PASSAGER. Si l’appareil n’est pas installé correctement, il risque

d’empêcher le fonctionnement du coussin d’air, et si le coussin

se déploie, l’appareil risque d’être projeté dans l’habitacle,

causant un accident et des blessures.

EFFECTUER CORRECTEMENT LES CONNEXIONS. Il y a risque de

blessures ou de dommages à l’appareil.

Attention

UTILISER LES ACCESSOIRES SPECIFIES ET LES INSTALLER CORRECTEMENT.

Utiliser uniquement les accessoires spécifiés. L’utilisation d’autres

composants que les composants spécifiés peut causer des dommages

internes à cet appareil ou son installation risque de ne pas être effectuée

correctement. Les pièces utilisées risquent de se desserrer et de provoquer

des dommages ou une défaillance de l’appareil.

NE PAS INSTALLER A DES ENDROITS TRES HUMIDES OU POUSSIEREUX. Eviter

d’installer l’appareil à des endroits soumis à une forte humidité ou à de la

poussière en excès. La pénétration d’humidité ou de poussière à l’intérieur

de cet appareil risque de provoquer une défaillance.

FAIRE INSTALLER LE CABLAGE ET L’APPAREIL PAR DES EXPERTS. Le câblage

et l’installation de cet appareil requiert des compétences techniques et

de l’expérience. Pour garantir la sécurité, faire procéder à l’installation

de cet appareil par le distributeur qui vous l’a vendu.

FAIRE CHEMINER LE CABLAGE DE MANIERE A NE PAS LE COINCER CONTRE

UNE ARETE METALLIQUE. Faire cheminer les câbles à l’écart des pièces

mobiles (comme les rails d’un siège) et des arêtes acérées ou pointues.

Cela évitera ainsi de coincer et d’endommager les câbles. Si un câble

passe dans un orifice métallique, utiliser un passe-cloison en

caoutchouc pour éviter que la gaine isolante du câble ne soit

endommagée par le rebord métallique de l’orifice.

INTERROMPRE TOUTE UTILISATION EN CAS DE PROBLEME. Le non-respect

de cette précaution peut entraîner des blessures ou endommager

l’appareil. Retourner l’appareil auprès du distributeur Alpine agréé ou

un centre de service après-vente Alpine en vue de la réparation.

Attention

Warning

DO NOT DISASSEMBLE OR ALTER. Doing so may result in an

accident, fire or electric shock.

KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF THE REACH OF

CHILDREN. Swallowing them may result in serious injury. If

swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE

OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT. Doing

so may obstruct forward vision or hamper movement etc. and

results in serious accident.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When

drilling holes in the chassis for installation, take precautions so

as not to contact, damage or obstruct pipes, fuel lines, tanks or

electrical wiring. Failure to take such precautions may result in

fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS

TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake

or steering systems (or any other safety-related system), or tanks

should NEVER be used for installations or ground connections.

Using such parts could disable control of the vehicle and cause

fire etc.

DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR

BAG. If the unit is not installed correctly the air bag may not

function correctly and when triggered the air bag may cause the

monitor to spring upwards causing an accident and injuries.

MAKE THE CORRECT CONNECTIONS. Failure to make the proper

connections may result in fire or product damage.

Caution

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other

than designated parts may damage this unit internally or may

not securely install the unit in place. This may cause parts to

become loose resulting in hazards or product failure.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of

moisture or dust. Moisture or dust that penetrates into this unit

may result in product failure.

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring

and installation of this unit requires special technical skill and

experience. To ensure safety, always contact the dealer where you

purchased this product to have the work done.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A

SHARP METAL EDGE. Route the cables and wiring away from

moving parts (like the seat rails) or sharp or pointed edges. This

will prevent crimping and damage to the wiring. If wiring passes

through a hole in metal, use a rubber grommet to prevent the

wire’s insulation from being cut by the metal edge of the hole.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so

may cause personal injury or damage to the product. Return it

to your authorized Alpine dealer or the nearest Alpine Service

Center for repairing.

Warning

This label is intended to alert the user to the

presence of important operating instructions.

Failure to heed the instructions will result in

severe injury or death.

This label is intended to alert the user to the

presence of important operating instructions.

Failure to heed the instructions can result in

injury or material damage.

Caution

Avertissement

Cette étiquette a pour but de prévenir

l’utilisateur de la présence d’instructions

importantes. Si ces instructions ne sont pas

suivies, des blessures graves ou mortelles

risquent d’être occasionnées.

Cette étiquette a pour but de prévenir l’utilisateur

de la présence d’instructions importantes. Si

ces instructions ne sont pas suivies, des

blessures ou des dommages matériels risquent

d’être occasionnés.

Contents / Contenu

Installation / Installation

Parts List / Liste des pièces

...................................................................................

Woofer Installation / Installation du Woofer

............................................................

Midrange Installation / Installation du haut-parleur médial

....................................

Tweeter Installation / Installation du Tweeter

.........................................................

Network Installation / Installation du circuit

............................................................

Network connections / Connexions du circuit

........................................................

Crossover Network / Circuit répartiteur

Crossover Network Introduction / Introduction au circuit répartiteur ................

9/25

Jumper Group Function / Fonction de groupe cavalier...................................

10/26

System Type 1 / Type de système 1 ................................................................

13/29

System Description / Description du système .............................................

13/29

Network Jumper Setting / Réglage du cavalier du circuit ...........................

14/30

System Type 2 / Type de système 2 ................................................................

16/32

System Description / Description du système .............................................

16/32

Network Jumper Setting / Réglage du cavalier du circuit ...........................

17/33

System Type 3 / Type de système 3 ................................................................

19/35

System Description / Description du système .............................................

19/35

Network Jumper Setting / Réglage du cavalier du circuit ...........................

20/36

System Type 4 / Type de système 4 ................................................................

22/38

System Description / Description du système ............................................. 22/38

Network Jumper Setting / Réglage du cavalier du circuit ...........................

23/39

Others / Autres

External dimensions / Dimensions externes........................................................

Specifications / Spécifications..............................................................................

English/Fran

çais

English

Main Unit

Grille Ring

Grille

Adapter Ring

Screw M4 x 12

Screw ø4 x 19

Unité principale

Bague de la grille

Grille

Vis M4 x 12

Vis ø4 x 19

Clé hexagonale

Français

Bague d’accouplement

Hexagonal

Wrench

English

Main Unit

Grille Ring

Unité principale

Bague de la grille

Grille

Vis ø4 x 19

Français

Grille

Screw ø4 x 19

Parts List / Liste des pièces

er t io

;

X10X10

Woofer / Woofer

Midrange / Haut-parleur médial

Tweeter / Tweeter

3-way network / Circuit répartiteur à 3 voies

X10X8X4

X2 X2 X2 X2

X2 X2 X2

X2 X2 X2 X2 X2 X2 X2

X2X2

English

Main Unit

Mounting Cup

Terminal Cover

Spring

Mounting Clip

Screw ø4 x 19

Screw

M4 x 25

M4 Nut

;

Mounting Ring

Screw ø4 x 12

Gasket

Unité principale

Couvre-bornes

t Ressort

Collier de fixation

Vis ø4 x 19

Vis M4 x 25

Écrou M4

;

Bague de montage

Vis ø4 x 12

Garniture

Français

Coupelle de

montage

English

Français

Crossover network

Jumper Puller

Screw ø4 x 19

Circuit répartiteur

Mécanisme de tirage du cavalier

Vis ø4 x 19

Woofer Installation / Installation du Woofer

Speaker Wire

Connections /

Raccordement des fils

d’enceinte

1. Insert the speaker wires

through the connection

holes. / Insérer les fils

d’enceinte dans les trous

de raccordement.

2. Fasten with a hexagonal

wrench. / Serrer avec

une clé hexagonale.

Installation without a grille / Installation sans grille

Installation with a grille / Installation avec grille

Installation with adapter rings / Installation avec bagues d’accouplement

English/Fran

çais

Midrange Installation / Installation du haut-parleur médial

Installation without a grille / Installation sans grille

Installation with a grille / Installation avec grille

Speaker Wire

Connections /

Raccordement des fils

d’enceinte

1. Insert the speaker wires

through the connection

holes. / Insérer les fils

d’enceinte dans les trous

de raccordement.

2. Fasten with a hexagonal

wrench. / Serrer avec

une clé hexagonale.

Tweeter Installation / Installation du Tweeter

Installation with springs / Installation avec ressorts

Installation with a mounting cup (Installation from the front)/

Installation with fastening rings / Installation avec bagues de serrage

Apply the supplied terminal

cover to prevent short circuits

from occurring when metallic

or other conductors are in the

vicinity of the installation

area. / Appliquer le couvre-

bornes fourni afin d’éviter que

des court-circuits ne se

produisent lorsque des

conducteurs métalliques ou

autres se trouvent à proximité

de la zone d’installation.

Installation avec coupelle de montage (Installation par l’avant)

English/Fran

çais

Network Installation / Installation du circuit

Note /Remarque:

Do not install the Crossover network where it will be exposed to moisture such as

under the floor mat or near the air conditioner. This may cause a malfunction./

Ne pas installer le circuit répartiteur dans un endroit où il sera exposé à l’humidité,

comme sous la moquette ou près du climatiseur. Cela risque de provoquer un mauvais

fonctionnement.

Network connections / Connexions du circuit

Caution

Connection Example 1 / Exemple de connexion 1

When connecting to single amp/single wiring / Lors du raccordement avec un seul amplificateur/

câblage simple.

Connection Example 2 / Exemple de connexion 2

When connecting to bi-amp/bi-wiring / Lors du raccordement avec deux amplificateurs/câblage

double.

Insert the signal link jumpers highlighted in gray firmly following each connection example. If the

jumper is not connected properly as described, it might result in malfunction of amplifier.

Insérez fermement les cavaliers de liaison de signal soulignés en gris en suivant chaque exemple de

raccordement. Si le cavalier n’est pas relié correctement comme décrit, il pourrait avoir comme

conséquence le défaut de fonctionnement de l’amplificateur.

Connect properly by following the manual. Otherwise it might result in fire or

accident.

Reliez correctement en suivant le manuel. Autrement il pourrait avoir comme

conséquence le feu ou des accidents.

Précaution

Connection Example 3 / Exemple de connexion 3

When connecting to tri-amp/tri-wiring / Lors du raccordement avec trois amplificateurs/câblage triple.

WF/MID

SIGNAL

LINK

MID/TW

SIGNAL

LINK

Amplifier/

Amplificateur

–

Amplifier/

Amplificateur

Amplifier/

Amplificateur

WF/MID

SIGNAL

LINK

MID/TW

SIGNAL

LINK

–

Amplifier/

Amplificateur

Amplifier/

Amplificateur

Amplifier/

Amplificateur

WF/MID

SIGNAL

LINK

MID/TW

SIGNAL

LINK

–

English

Crossover Network Introduction

It is common knowledge that the automotive interior is one of the most inhospitable

environments for high-fidelity sound, and that every vehicle poses its own unique set of

installation and acoustic challenges. While many of these problems can often be over-

come with proper speaker placement, equalization, or other techniques, the attempt is

a time consuming task without guaranteed results. Yet with all these tools and methods

available, it is surprising to realize that one of the most powerful tuning tools has been

misunderstood or neglected by so many for so long. It is for this reason that Alpine has

developed the most advanced crossover network design in the history of car audio.

Much of the difference between demo-board and in-car performance can be attributed

to the fact that crossover networks have been traditionally tuned for only one specific

application – usually the demo-board. Without taking into account typical real world

installations, the transition between drivers and resultant frequency response will be

degraded for the majority of vehicles that installers are confronted with today. Through

Alpine’s unique phase coherent flat summation design methodology, however, it is now

possible to optimize performance for a variety of installations by intentionally altering

various filter characteristics. By achieving an “in-phase” condition between drivers in

the overlapping frequency range at the listening position, image smear, response aber-

rations and other typical problems can be dramatically reduced or eliminated altogether.

This “phase linkage” technique can be thought of as a kind of passive time correction in

the crossover region.

With Alpine’s introduction of such revolutionary processing technologies as digital time

correction and adaptive equalization, all of this may seem superlative. Unfortunately

however, such processing can significantly increase system complexity and therefore

may not be practical for every situation. Additionally, without careful use of time correc-

tion for each individual speaker in the system, integration problems between them can

remain. Subsequently, it may be advantageous to use such processing to compensate

for seating position bias in conjunction with the phase correction of the passive network

for the transition between individual drivers. Simply stated, the flexibility of the

AlpineF#1Status™ crossover network allows it to be a complimentary solution for achiev-

ing the best of both worlds, either as a stand alone solution or an integral component of

a partially active system.

As with all AlpineF#1Status™ products, it is the attention to the smallest details that

truly brings out ultimate performance... or in a word, MicroDynamics™. From the hand

coated crosscut wood fiber cones to the symmetric drive motor structures, nothing is

left to chance. This philosophy is carried throughout every aspect of the SPX-Z18T

speaker system, including the components, layout and design of the crossover network.

All series capacitors are the highest grade metalized polypropylene, and all series

inductors are heavy gauge air core. Even parallel inductors are of powder core con-

struction, to maximize consistancy and sound quality. All elements are intentionally placed

in such a way to as to minimize any chance for magnetic or thermal influence, and all

signal path lengths are minimized with extra heavy circuit board traces. In the end, this

level of quality and attention to detail has but one purpose, to bring true sonic realism to

the automotive environment once and for all.

Jumper Group Function

Although recommendations are made for the most common system types in the following

pages, there are actually over 1000 unique and useful jumper combinations available for a

wide variety of vehicles, installations and personal tastes. While this flexibility has obvious

advantages, too many choices can also be confusing. Therefore, it will be helpful to under-

stand the function of each jumper group in order to tune the network more effectively:

TW-HP:

In addition to functioning as a high-pass filter, this section also provides the necessary

adjustments for proper integration with the midrange. The transition between these two

drivers in the frequency and time domains is essential to the total performance of a

multi-element system, as it has a direct effect upon imaging, staging, focus

and tonal balance. In real world installations, distance and angle of both drivers relative

to the listener, their proximity to each other, and certainly the vehicle's interior also exert

additional influence. In anticipation of this, variations of filter slope, Q, cut-off frequency

and resultant phase shift are provided so that "phase linkage" and flat summation can

be maintained. As a general reference, the layout and available filter types of the tweeter

high-pass section are provided below:

TW LEVEL:

In general, this section provides precise level adjustment for optimum performance or

personal taste. However, it also allows for “tilting” of the filter frequency response in

order to compensate for the natural high frequency roll-off associated with off-axis lis-

tening angles. In other words, this jumper choice will have a direct effect on both Q and

cut-off frequency of the various filter combinations listed above. This effect can be seen

in the filter transfer function graphs for the various system types. If the TW-HP section is

set to bypass in favor of an electronic crossover, the off-axis feature will no longer func-

tion, but basic level adjustment will still be possible.

R1 = 1.5Ω

R2 = 3.3Ω

R3 = 4.7Ω

R4 = 5.6Ω

R5 = 0.5Ω

C1 = 3.3µF

C2 = 8.2µF

L1 = 0.65mH

L2 = 0.1mH

HP-1

HP-2

BYPASS

+1.5dB/15°

0dB/0°

–1.5dB

–3dB

L1 L2

+4dB/30°

HP-3

–

Order:

• No HP jumpers

• HP3

Order:

• HP1 + HP2 + HP3

• HP1 + HP3

• HP2 + HP3

Order:

• HP1

• HP2

• HP1 + HP2

English

R6 = 1.0Ω

R7 = 1.0Ω

R8 = 22Ω

C3 = 18µF

C4 = 33µF

C5 = 10µF

L3 = 0.32mH

L4 = 2.0mH

L5 = 2.9mH

MID HP/LP:

As a selectable bandpass filter for the midrange, the net effect of this section is naturally

linked to the selections made in the tweeter high-pass and woofer low-pass sections.

Achieving the most phase coherent and flat summation possible requires controlling

the amount of inherent phase shift of each filter, and is directly related to the selection of

filter order, Q and cut-off frequency. Again, this relationship is also affected by the dis-

tance and angle of each driver relative to the listener and their proximity to each other.

Since the acoustic center of the midrange will be farther back than the tweeter in nearly

all applications, minimal delay is desirable in the midrange low-pass. Subsequently, this

filter is of low order, and leaves much of the adjustment capability for the mid/tweeter

transition to the tweeter high-pass section. For the midrange high-pass, higher order

configurations are used in most applications to achieve phase linkage with the woofer

(see WF-LP section). For general reference, the available midrange network configura-

tions are listed below. In certain installations where positioning or placement necessi-

tates level adjustment, a jumper is provided that boosts midrange output by approxi-

mately +2dB. As an additional note, either filter (high-pass or low-pass) may be by-

passed independently for semi-active applications.

HP-2

HP BYPASS

LP BYPASS

+2dB

L4 L5

C3R6

C4 R7

HP-1

LP-2

LP-1

–

Order HP:

• No HP jumpers

• HP2 (semi-2

Order)

Order LP:

• LP1

• LP2

Order HP:

• HP1

Order HP:

• HP1 + HP2

WF-LP:

While functioning as a low-pass filter for the woofer, this section also provides a wide

degree of adjustments for optimizing performance and system integration. Since it is

often difficult to position the woofer and midrange close together or at equal distances,

it is critical to achieve phase linkage between them to avoid localization, image smear,

poor staging, etc. Additionally, vehicle interior dimensions are typically close to the wave-

length of the woofer/midrange crossover region, so it may be necessary to minimize

overlap to reduce the chance of generating a complex canceling sound field or re-

sponse aberrations. Therefore, a variety of higher order filter types and characteristics

are provided in this section, making it possible to link the two drivers in relative phase

for a smooth transition in many applications. Again, it is important to note that the selec-

tions made in both the WF-LP and MID-HP sections produce a net effect, and must be

set in such a way so as to work together. As a general reference, the available woofer

low-pass filter configurations are listed below.

R9 = 2.2Ω

R10 = 1.5Ω

C6 = 100µF

C7 = 47µF

C8 = 220µF

L6 = 0.65mH

L7 = 0.65mH

BYPASS

L6 L7

R10R9

C7C6 C8

LP-1

LP-2

LP-3

–

SIGNAL LINK:

The signal link jumpers provide a parallel connection between the input sides of the

terminal blocks, eliminating the need for extra terminals or wiring when using a single or

dual input.

Caution:

These jumpers

must be removed accordingly when used in a bi-amp or tri-amp

configuration to prevent possible damage to amplifiers.

Order:

• No HP jumpers

Order:

• LP2

• LP3

• LP2 + LP3

Order:

• LP1

Order:

• LP1 + LP2

• LP1 + LP3

• LP1 + LP2 + LP3

Jumper Group Function

English

System Type 1

• Type-1B

is for such

cases where

pathlength is

nearly the same to

all drivers, but

where the mount-

ing surface

orientation creates

a uniform but fairly

extreme off-axis

listening angle.

System Description

With all three drivers mounted close together and equidistant to the listening position,

this is surely the most favorable configuration for a component speaker system. Al-

though such an installation may not often be practical in situations other than the demo-

board, it is certainly possible given the custom fabrication techniques available today. In

anticipation this, a degree of tolerance is built into the settings described below for the

most likely cases, though some experimentation may be necessary if all conditions

cannot be met. If choosing to go beyond the recommended settings or utilizing the

network in a partially active mode, keep in mind that phase coherence and flat summa-

tion remains critical even in the idyllic flat baffle situation, as each driver type exhibits

unique phase and group delay characteristics.

• Type-1A is the

default setting of the

network, and

assumes essentially

on-axis positioning

and equal

pathlength of all

drivers relative to

the listening

position.

System Type 1

–10

–20

–30

–40

–50

20Hz 30Hz

100Hz

1.0KHz 3.0KHz 10KHz 30KHz300Hz

Type-1A: Pathlength to the listening posi-

tion is considered to be basically equal in

this case (ideally 2-3m away), with relative

on-axis positioning of all drivers. Phase link-

age is accomplished with a low Q 2

Order

high-pass filter on the tweeter, 1

Order low-

pass and 4

Order high-pass on the

midrange, and a semi-4

Order low-pass on

the woofer. This results in acoustic crosso-

ver points of 3.8kHz and 700Hz respectively.

Network Jumper Setting

HP-2

HP-1

LP-2

LP-1

+2dB

MID HP/LP

–3dB

–1.5dB

0dB/0

+1.5dB/15

+4dB/30

HP-1

HP-2

HP-3

BYPASS

LP-1

LP-2

LP-3

LP-BYPASS

HP-BYPASS

TW LEVEL

WF LP

MID HP/LP

WF/MID

SIGNAL LINK

SPX–Z18T

TW HP

MID/TW

SIGNAL LINK

—

Notes:

• Highlighted tweeter level jumpers are the recommended settings for each configura-

tion, but user adjustment may be desirable.

• Transfer function simulations only illustrate the effect of the filter upon the input sig-

nal, and therefore do not represent the actual frequency response of the system.

• If separate channels of amplification are used (bi-wire or tri-wire mode), the appro-

priate signal link jumpers must be removed.

English

–10

–20

–30

–40

–50

20Hz 30Hz

100Hz

1.0KHz 3.0KHz 10KHz 30KHz300Hz

Type-1B: While the mounting configuration

is the same as Type-1A, this network set-

ting provides a variation for when personal

taste, positioning or vehicle acoustics neces-

sitates more high frequency output from the

midrange and tweeter. Rear deck installa-

tion is one particular example where the

extreme off-axis positioning will require such

level compensation due to the natural roll-

off. Although this will also result in some

additional delay of the woofer, it does not

exert significant influence in this case. The

resultant acoustic crossover points are the

same as indicated above.

Network Jumper Setting

HP-2

HP-1

LP-2

LP-1

+2dB

MID HP/LP

–3dB

–1.5dB

0dB/0

+1.5dB/15

+4dB/30

HP-1

HP-2

HP-3

BYPASS

LP-1

LP-2

LP-3

LP-BYPASS

HP-BYPASS

TW LEVEL

WF LP

MID HP/LP

WF/MID

SIGNAL LINK

SPX–Z18T

TW HP

MID/TW

SIGNAL LINK

—

Notes:

• Highlighted tweeter level jumpers are the recommended settings for each configura-

tion, but user adjustment may be desirable.

• Transfer function simulations only illustrate the effect of the filter upon the input sig-

nal, and therefore do not represent the actual frequency response of the system.

• If separate channels of amplification are used (bi-wire or tri-wire mode), the appro-

priate signal link jumpers must be removed.

System Type 2

• Type-2A

takes into

account that all

drivers are mounted

more or less flush

to the panel on a

mostly flat vertical

surface such as the

door, thus present-

ing varying degrees

of both axis and

distance of each

driver to the

listener.

• Type-2B

is the

same as above,

but assumes the

woofer somewhat

farther away than

is typical. This will

accommodate

different vehicle

types as well as

kick panel mount-

ing of the woofer.

System Description

As one of the more common applications, this installation type is the most likely to be

accommodated by factory speaker locations to some degree, thus requiring the least

amount of custom fabrication. However, due to the mounting arrangement and surface

orientation, it also results in significant differences in distance and angle of all three

drivers relative to the listener. In order to optimize performance in this case, it especially

critical to link each driver together in relative phase throughout the transitional crosso-

ver regions, while also taking into account the frequency response effects of the various

off-axis listening angles of each driver. Two network configurations are provided for the

most typical variations of this installation type, each employing specific phase correc-

tion and response compensation. Again, please note that the tuning of the settings

below considers the best balance between driver and passenger listening positions, so

all distances and angles are referenced to the nearest side.

Also worth noting is the fact that the shorter near side pathlenths to the midrange and

tweeter will result in more dramatic seating position bias than other installation types.

While it is possible to adjust each network individually in order to specifically tune for

one listening position, it will often be more beneficial to utilize basic time correction to

correct for this left/right pathlength difference if available. In general though, a high

tweeter location is thought to be advantageous for improving perceived height and width

of the soundstage, as well as achieving a strong high frequency output level.

English

–10

–20

–30

–40

–50

20Hz 30Hz

100Hz

1.0KHz 3.0KHz 10KHz 30KHz300Hz

Type-2A: For the tweeter in this case,

pathlength from the listening position is con-

sidered to be 85cm, at approximately 15-

20° off-axis. Located at a moderate vertical

distance down from the tweeter and basi-

cally flush to the panel, the midrange is

8.5cm farther away and presents a listening

angle of about 40-50°. Due to the low door

woofer location however, the listening angle

for the woofer is close to 60° off-axis, with

its acoustic center 8cm farther relative to the

mid. For the tweeter/mid transition, a 3rd

order high-pass and semi-1st order low-pass

with increased level on the mid are engaged,

resulting in a summation point of 4kHz. Op-

timum integration between the woofer and

mid is then achieved with 4th order high-pass

and low-pass at 700Hz.

Network Jumper Setting

HP-2

HP-1

LP-2

LP-1

+2dB

MID HP/LP

–3dB

–1.5dB

0dB/0

+1.5dB/15

+4dB/30

HP-1

HP-2

HP-3

BYPASS

LP-1

LP-2

LP-3

LP-BYPASS

HP-BYPASS

TW LEVEL

WF LP

MID HP/LP

WF/MID

SIGNAL LINK

SPX–Z18T

TW HP

MID/TW

SIGNAL LINK

—

Notes:

• Highlighted tweeter level jumpers are the recommended settings for each configura-

tion, but user adjustment may be desirable.

• Transfer function simulations only illustrate the effect of the filter upon the input sig-

nal, and therefore do not represent the actual frequency response of the system.

• If separate channels of amplification are used (bi-wire or tri-wire mode), the appro-

priate signal link jumpers must be removed.

–10

–20

–30

–40

–50

20Hz 30Hz

100Hz

1.0KHz 3.0KHz 10KHz 30KHz300Hz

Type-2B: Tweeter and midrange positioning

are the same as in Type-2A, but the woofer

is located farther forward. This results in a

more extreme woofer listening angle of ap-

proximately 70°, with a delay of 28cm rela-

tive to the mid. Subsequently, level attenua-

tion is applied to both the tweeter and mid

while also adjusting filter characteristics

appropriatly for the mid/woofer transition. In

this case, changing the midrange high-pass

to a low Q 3rd order and the woofer low-

pass to very high Q 2nd order results in an

acoustic crossover point of 500Hz.

Network Jumper Setting

HP-2

HP-1

LP-2

LP-1

+2dB

MID HP/LP

–3dB

–1.5dB

0dB/0

+1.5dB/15

+4dB/30

HP-1

HP-2

HP-3

BYPASS

LP-1

LP-2

LP-3

LP-BYPASS

HP-BYPASS

TW LEVEL

WF LP

MID HP/LP

WF/MID

SIGNAL LINK

SPX–Z18T

TW HP

MID/TW

SIGNAL LINK

—

Notes:

• Highlighted tweeter level jumpers are the recommended settings for each configura-

tion, but user adjustment may be desirable.

• Transfer function simulations only illustrate the effect of the filter upon the input sig-

nal, and therefore do not represent the actual frequency response of the system.

• If separate channels of amplification are used (bi-wire or tri-wire mode), the appro-

priate signal link jumpers must be removed.

System Type 2

La page charge ...

Alpine SPX-Z18M Le manuel du propriétaire

Marque: Alpine

Modèle: SPX-Z18M

Catégorie: Haut-parleurs de voiture

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Alpine SPX-Z18M Owner's manual

Alpine SPX-Z18M Le manuel du propriétaire

Alpine SPX-Z18M Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents