Oracle 7116970 Guide d'installation

Oracle

®

Storage 12 Gb SAS PCIe RAID

HBA, Internal: 16 Port and 2 GB Memory

Installation Guide For HBA Model

7116970

Part No: E87592-01

September 2017

Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model 7116970

Part No: E87592-01

This software and related documentation are provided under a license agreement containing restrictions on use and disclosure and are protected by intellectual property laws. Except

as expressly permitted in your license agreement or allowed by law, you may not use, copy, reproduce, translate, broadcast, modify, license, transmit, distribute, exhibit, perform,

publish, or display any part, in any form, or by any means. Reverse engineering, disassembly, or decompilation of this software, unless required by law for interoperability, is

prohibited.

The information contained herein is subject to change without notice and is not warranted to be error-free. If you find any errors, please report them to us in writing.

If this is software or related documentation that is delivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, then the following notice is applicable:

U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,

delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental

regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the

hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

This software or hardware is developed for general use in a variety of information management applications. It is not developed or intended for use in any inherently dangerous

applications, including applications that may create a risk of personal injury. If you use this software or hardware in dangerous applications, then you shall be responsible to take all

appropriate fail-safe, backup, redundancy, and other measures to ensure its safe use. Oracle Corporation and its affiliates disclaim any liability for any damages caused by use of this

software or hardware in dangerous applications.

Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.

Intel and Intel Xeon are trademarks or registered trademarks of Intel Corporation. All SPARC trademarks are used under license and are trademarks or registered trademarks of

SPARC International, Inc. AMD, Opteron, the AMD logo, and the AMD Opteron logo are trademarks or registered trademarks of Advanced Micro Devices. UNIX is a registered

trademark of The Open Group.

This software or hardware and documentation may provide access to or information about content, products, and services from third parties. Oracle Corporation and its affiliates are

not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services unless otherwise set forth in an applicable agreement

between you and Oracle. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content,

products, or services, except as set forth in an applicable agreement between you and Oracle.

Access to Oracle Support

Oracle customers that have purchased support have access to electronic support through My Oracle Support. For information, visit http://www.oracle.com/pls/topic/lookup?

ctx=acc&id=info or visit http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs if you are hearing impaired.

Référence: E87592-01

Ce logiciel et la documentation qui l'accompagne sont protégés par les lois sur la propriété intellectuelle. Ils sont concédés sous licence et soumis à des restrictions d'utilisation et

de divulgation. Sauf stipulation expresse de votre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire, traduire, diffuser, modifier, accorder de licence, transmettre,

distribuer, exposer, exécuter, publier ou afficher le logiciel, même partiellement, sous quelque forme et par quelque procédé que ce soit. Par ailleurs, il est interdit de procéder à toute

ingénierie inverse du logiciel, de le désassembler ou de le décompiler, excepté à des fins d'interopérabilité avec des logiciels tiers ou tel que prescrit par la loi.

Les informations fournies dans ce document sont susceptibles de modification sans préavis. Par ailleurs, Oracle Corporation ne garantit pas qu'elles soient exemptes d'erreurs et vous

invite, le cas échéant, à lui en faire part par écrit.

Si ce logiciel, ou la documentation qui l'accompagne, est livré sous licence au Gouvernement des Etats-Unis, ou à quiconque qui aurait souscrit la licence de ce logiciel pour le

compte du Gouvernement des Etats-Unis, la notice suivante s'applique :

U.S. GOVERNMENT END USERS: Oracle programs, including any operating system, integrated software, any programs installed on the hardware, and/or documentation,

delivered to U.S. Government end users are "commercial computer software" pursuant to the applicable Federal Acquisition Regulation and agency-specific supplemental

regulations. As such, use, duplication, disclosure, modification, and adaptation of the programs, including any operating system, integrated software, any programs installed on the

hardware, and/or documentation, shall be subject to license terms and license restrictions applicable to the programs. No other rights are granted to the U.S. Government.

Ce logiciel ou matériel a été développé pour un usage général dans le cadre d'applications de gestion des informations. Ce logiciel ou matériel n'est pas conçu ni n'est destiné à être

utilisé dans des applications à risque, notamment dans des applications pouvant causer un risque de dommages corporels. Si vous utilisez ce logiciel ou ce matériel dans le cadre

d'applications dangereuses, il est de votre responsabilité de prendre toutes les mesures de secours, de sauvegarde, de redondance et autres mesures nécessaires à son utilisation dans

des conditions optimales de sécurité. Oracle Corporation et ses affiliés déclinent toute responsabilité quant aux dommages causés par l'utilisation de ce logiciel ou matériel pour des

applications dangereuses.

Oracle et Java sont des marques déposées d'Oracle Corporation et/ou de ses affiliés. Tout autre nom mentionné peut correspondre à des marques appartenant à d'autres propriétaires

qu'Oracle.

Intel et Intel Xeon sont des marques ou des marques déposées d'Intel Corporation. Toutes les marques SPARC sont utilisées sous licence et sont des marques ou des marques

déposées de SPARC International, Inc. AMD, Opteron, le logo AMD et le logo AMD Opteron sont des marques ou des marques déposées d'Advanced Micro Devices. UNIX est une

marque déposée de The Open Group.

Ce logiciel ou matériel et la documentation qui l'accompagne peuvent fournir des informations ou des liens donnant accès à des contenus, des produits et des services émanant de

tiers. Oracle Corporation et ses affiliés déclinent toute responsabilité ou garantie expresse quant aux contenus, produits ou services émanant de tiers, sauf mention contraire stipulée

dans un contrat entre vous et Oracle. En aucun cas, Oracle Corporation et ses affiliés ne sauraient être tenus pour responsables des pertes subies, des coûts occasionnés ou des

dommages causés par l'accès à des contenus, produits ou services tiers, ou à leur utilisation, sauf mention contraire stipulée dans un contrat entre vous et Oracle.

Accès aux services de support Oracle

Les clients Oracle qui ont souscrit un contrat de support ont accès au support électronique via My Oracle Support. Pour plus d'informations, visitez le site http://www.oracle.com/

pls/topic/lookup?ctx=acc&id=info ou le site http://www.oracle.com/pls/topic/lookup?ctx=acc&id=trs si vous êtes malentendant.

Contents

Using This Documentation ................................................................................. 7

1 HBA Overview ................................................................................................. 9

Ship Kit Contents ........................................................................................... 9

HBA Features ................................................................................................. 9

Operating System and Technology Requirements ................................................ 10

System Interoperability ................................................................................... 11

Host Platform Support ............................................................................ 11

Storage System Support .......................................................................... 11

Software Support ................................................................................... 12

2 Hardware Installation and Removal .............................................................. 13

Observing ESD and Handling Precautions ......................................................... 13

Best Practices for HBA Installation .................................................................. 14

Installing the HBA ........................................................................................ 14

▼ To Prepare for Hardware Installation ................................................... 14

▼ To Install the HBA ........................................................................... 15

▼ To Connect the HBA to Internal Storage Devices ................................... 16

▼ To Complete the Installation .............................................................. 17

Next Steps ................................................................................................... 17

Removing the HBA ....................................................................................... 17

▼ To Remove the HBA ........................................................................ 18

3 Creating a Bootable Drive in a Preboot Environment ................................... 19

About Creating a Bootable Drive in a Preboot Environment .................................. 19

Utilities Overview ................................................................................. 20

Methods for Creating a Bootable Drive ..................................................... 20

Creating a Bootable Drive (SPARC) ................................................................. 20

5

Contents

▼ To Create a Bootable Drive (SPARC) .................................................. 21

Using the pcli Utility to Create a Bootable Drive (SPARC) .......................... 21

Importing an Existing Logical Drive Configuration (SPARC) ........................ 25

Creating a Bootable Drive (x86) ...................................................................... 26

▼ To Create a Bootable Drive (x86) ....................................................... 26

Using the LSI MegaRAID Configuration Utility Menu to Create a Bootable

Logical Drive (x86) ............................................................................... 26

Validating the Label of the HBA Logical Drive .................................................. 41

▼ To Verify That the Label of a Logical Drive Is Valid ............................... 42

Next Steps ........................................................................................... 44

Installing the Oracle Solaris OS ....................................................................... 44

▼ To Prepare to Install the Oracle Solaris OS ........................................... 44

▼ To Install the Oracle Solaris OS .......................................................... 44

Next Steps ................................................................................................... 45

4 HBA Software Installation ............................................................................. 47

Installing the Utility for BIOS and Firmware Updates and RAID Configuration ......... 47

Installing Diagnostic Software ......................................................................... 48

Diagnostic Support for the Oracle Solaris OS ............................................. 48

Diagnostic Support for All Other Supported Operating Systems ..................... 48

Installing Drivers ........................................................................................... 49

Installing Drivers For the Oracle Solaris OS ............................................... 49

▼ Installing Drivers For All Other Supported Operating Systems .................. 50

5 Important Information and Known Issues ..................................................... 51

Mixing Drive Types on the HBA Might Cause Slow Repair of a Degraded Logical

Drive ........................................................................................................... 51

HBA Product Accessibility ............................................................................. 52

HBA Hardware Accessibility ................................................................... 52

Oracle ILOM Accessibility ..................................................................... 52

BIOS Accessibility ................................................................................ 53

Documentation Accessibility ................................................................... 54

A HBA Specifications ....................................................................................... 55

Physical Dimensions ...................................................................................... 55

Environmental Requirements ........................................................................... 55

Fault Tolerance ............................................................................................. 56

6 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

Using This Documentation

■

Overview – Describes how to install and remove the Oracle Storage 12 Gb SAS PCIe

RAID HBA, Internal: 16 Port and 2 GB Memory.

■

Audience – Technicians, system administrators, and authorized service providers

■

Required knowledge – Advanced experience troubleshooting and replacing hardware

Product Documentation Library

Documentation and resources for this product and related products are available at http://

docs.oracle.com/cd/E87591_01/index.html.

Feedback

Provide feedback about this documentation at http://www.oracle.com/goto/docfeedback.

Using This Documentation 7

8 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

1

♦ ♦ ♦ C H A P T E R 1

HBA Overview

This chapter provides an overview of the Oracle Storage 12 Gigabit (Gb) Serial Attached SCSI

(SAS) PCI Express (PCIe) RAID host bus adapter (HBA), Internal: 16 Port and 2 Gigabytes

(GB) Memory, which uses Broadcom technology. The chapter also describes the various

operating systems, host platforms, storage, and infrastructure configurations that support the

HBA.

This chapter contains the following topics:

■

“Ship Kit Contents” on page 9

■

“HBA Features” on page 9

■

“Operating System and Technology Requirements” on page 10

■

“System Interoperability” on page 11

Ship Kit Contents

■

Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory, with a

standard, low-profile bracket installed

■

Accessing Documentation document

HBA Features

The Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory (part

number: 7116970) is a low-profile, PCI Express 3.0 RAID controller that supports 16 internal

12 Gb/s SAS connectors through four internal mini-SAS HD ports. The 16 connectors on the

board enable direct connection to all internal drives, and eliminate the need for a SAS expander.

Data that is cached on the HBA is protected, in the event of a power failure.

The HBA supports the following features.

Chapter 1 • HBA Overview 9

Operating System and Technology Requirements

TABLE 1

HBA Features

Feature Description

Ports Four SAS3, x4 internal mini-SAS HD ports, 16 total phys

Host interface PCIe, as defined in the PCI Express Card Specification, version 3.0

Target interface SAS3 12-Gb/s

Lane width PCIe 3.0 x8 lane width up to 8 Gt/s per lane

Performance High, through the MegaRAID Firmware Interface (MFI) architecture

Throughput High throughput and low CPU utilization to offload the host processor

Boot support For all supported operating systems (OSs) (see Table 2, “Supported Operating

System/Technology Versions ,” on page 11)

Power consumption Maximum 25 Watts

Diagnostic support Provided by Oracle VTS

Oracle Solaris Dynamic Reconfiguration Supported

PCIe Single Root I/O Virtualization (SR-IOV) Supported

MSI-X Supported

PCIe hot-plug and hot-swap capabilities Supported

RAID ■ Full-featured, hardware-based RAID implementation

■ A RAID on CHIP (ROC) controller, supporting a hardware RAID acceleration

engine with a capacity of 2 GB, DDR-3 cache memory, and power fail backup

support

■ Integrated SAS/SMP/STP/SSP protocol support

■ 12 Gb/s SAS interface supporting 6 and 3 Gb/s SAS

■ Data striping across multiple drives

■ Data mirroring or parity block for backing up data

■ Support for RAID levels 0, 1, 5, 6, 10, 50, and 60, with 2 GB data cache, and with

accelerated XOR on RAID 5 and 6

■ Built-in flash controller for direct flash backup from DDR memory

■ User-configurable rebuild rate

Operating System and Technology Requirements

The HBA requires the operating system (OS) and technology levels, at minimum, listed in

Table 2, “Supported Operating System/Technology Versions ,” on page 11.

Note - If you need to contact Oracle Support, first verify that you have a supported OS installed

on the host system, and install the latest HBA driver, utility, and firmware versions. Updating

the system and HBA to the latest OS, driver, utility, and firmware versions might address the

issue, preventing the need to contact Oracle Support about an issue that has already been fixed.

10 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

System Interoperability

TABLE 2

Supported Operating System/Technology Versions

Operating System/Technology Recommended Versions (minimum)

Oracle Solaris OS for the x86 (64-

bit) platform

■ Oracle Solaris 11.3 with SRU 23

To obtain the latest SRUs, go to https://support.oracle.com

Oracle Virtual Machine (VM)

Technology

Oracle VM 3.4.4

Linux OS (64-bit) ■ Oracle Linux 7.3 (Red Hat Compatible Kernel (RHCK) and Unbreakable

Enterprise Kernel (UEK) 4, at minimum)

■ Oracle Linux 6.9 (RHCK and UEK4, at minimum)

Microsoft Windows OS (64-bit) ■ Window Server 2016

■ Windows Server 2012 R2

VMware Technology ■ VMware ESXi 6.5 U1

System Interoperability

This section provides host platform, storage, and software support information. This section

contains the following topics:

■

“Host Platform Support” on page 11

■

“Storage System Support” on page 11

■

“Software Support” on page 12

Host Platform Support

The HBA is supported by the platforms listed in Table 3, “Platform Support,” on page 11.

For the latest information, see your system product notes and server platform product web

pages.

TABLE 3

Platform Support

Platform Supported OS/Technology

Oracle x86 Servers:

Oracle Server X7-2, X7-2L, and X7-8 Oracle Solaris, Oracle VM, Windows, Linux

Storage System Support

Internal disk drives are the only storage supported by the HBA.

Chapter 1 • HBA Overview 11

System Interoperability

Software Support

Install, Flash, and BIOS configuration utilities are provided. The HBA uses the MegaRAID

Firmware Interface (MFI) architecture for all major operating systems, which allows for thinner

drivers for better performance. To obtain a device driver that supports your operating system, go

to: https://www.broadcom.com/support/oem/oracle/

Use the StorCLI utility to manage the HBA upon installation. For more information, go to:

https://www.broadcom.com/support/oem/oracle/

12 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

2

♦ ♦ ♦ C H A P T E R 2

Hardware Installation and Removal

This chapter describes how to install and remove the HBA. For detailed instructions, see your

storage system installation or service guide and the installation guide for the storage devices to

be connected to the HBA.

This chapter contains the following topics:

■

“Observing ESD and Handling Precautions” on page 13

■

“Installing the HBA” on page 14

■

“Next Steps” on page 17

■

“Removing the HBA” on page 17

Observing ESD and Handling Precautions

Caution - Damage to the HBA can occur as the result of careless handling or electrostatic

discharge (ESD). Always handle the HBA with care to avoid damage to electrostatic-sensitive

components.

To minimize the possibility of ESD-related damage, use both a workstation antistatic mat and

an ESD wrist strap. You can get an ESD wrist strap from any reputable electronics store or from

Oracle as part number 250-1007.

Observe the following precautions to avoid ESD-related problems:

■

Leave the HBA in its antistatic bag until you are ready to install it in the system.

■

Always use a properly fitted and grounded wrist strap or other suitable ESD protection

when handling the HBA and observe proper ESD grounding techniques.

■

Always hold the HBA by the metal enclosure.

■

Place the HBA on a properly grounded antistatic work surface pad when it is out of its

protective antistatic bag.

Chapter 2 • Hardware Installation and Removal 13

Best Practices for HBA Installation

Follow these general best practices for installing and configuring the HBA:

■

If more than one HBA model is present in the configuration, enable only the OptionROM

(OpROM) for the first HBA seen in the boot sequence. There is a limited amount of space

for OpROMs; therefore, do not unnecessarily enable all OpROMs, as space usage issues

might occur.

■

When installing the HBA, be sure to also install the latest version of the command-line

utility available from the manufacturer's web site. Keep the HBA utilities, firmware, and

drivers up-to-date, and update them in that order.

Installing the HBA

This section provides the following procedures:

■

“To Prepare for Hardware Installation” on page 14

■

“To Install the HBA” on page 15

■

“To Connect the HBA to Internal Storage Devices” on page 16

■

“To Complete the Installation” on page 17

To Prepare for Hardware Installation

1.

Read and observe the safety information for this product.

See the Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory

Safety and Compliance Guide at: http://docs.oracle.com/cd/E87591_01/index.html.

2.

Familiarize yourself with the physical features of the HBA and the RAID levels

that it supports.

3.

Ensure that you have the right quantity of initialized disk drives for the RAID

level you want to use for the arrays.

For optimal performance, use drives of the same type, speed, and size when you create virtual

drives. You can use different-sized disk drives in the array, but the array will be limited to the

capacity of the smallest and slowest disk drive.

For more information, refer to the 12 Gb/s MegaRAID SAS Software User's Guide at: https://

www.broadcom.com/support/oem/oracle/

14 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

To Install the HBA

4.

Ensure that you have the proper cables for the HBA and the internal disk drives.

Use only Oracle-provided SAS cables (provided with your Oracle system at time of purchase).

Cable connectors are keyed so that you cannot insert them incorrectly.

5.

Unpack the box containing the HBA in a static-free environment and inspect it

for damage.

Note - Leave the HBA in the protective bag until you are ready to install it. If there is damage,

contact Oracle customer support.

6.

Refer to your system installation guide or service manual for instructions on

how to remove the system cover, disconnect the AC power cords, and turn off

power from the system, if required.

To Install the HBA

1.

Attach an antistatic wrist strap and remove the HBA from its protective bag.

See “Observing ESD and Handling Precautions” on page 13.

2.

Refer to the installation guide or service manual for your particular system for

instructions on how to locate an available PCIe slot in the system.

3.

Align the PCIe bus connector of the HBA to the PCIe slot.

Note - Some PCIe slots support PCIe graphics cards only; if the HBA is installed in one of

those PCIe slots, the HBA will not function.

Chapter 2 • Hardware Installation and Removal 15

To Connect the HBA to Internal Storage Devices

4.

Press down gently and firmly to seat the HBA in the PCIe slot, and then secure

the bracket to the system chassis with the retention clip (see the following

figure).

Note - The configuration of the enclosure might not be the same as shown in this illustration.

To Connect the HBA to Internal Storage Devices

1.

Install and configure the SAS devices in the system.

For more information, see the documentation for the devices.

2.

Connect the SFF-8643 x4 Mini SAS HD connector on one end of the SAS cable to

an internal port.

Use only Oracle-provided SAS cables (provided with your Oracle system at time of purchase).

16 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

To Complete the Installation

1.

Replace the system cover and reconnect the AC power cords, if required, as

described in the system documentation.

2.

If you needed to turn the system power off to install the HBA, power on the

system.

Note - If you do need to return power to the system, ensure that the power is turned on to the

SAS devices before or at the same time that the power is turned on to the host system. If the

system is powered up before these devices, the devices might not be recognized.

3.

If you need to install an operating system (OS) on your system, complete the

procedures in Chapter 3, “Creating a Bootable Drive in a Preboot Environment ”

and then go to the next step.

4.

If you already have an OS installed on an x86 system, do the following:

a.

Go to the Oracle support area of the Broadcom web site (https://www.

broadcom.com/support/oem/oracle/) and download the StorCLI utility, along with

supporting documentation.

b.

Install the StorCLI utility on the system that will manage your storage.

c.

From the StorCLI utility, create logical drives for the HBA.

Next Steps

If you are using the Oracle Solaris OS, the installation is complete. You can obtain the latest

SRUs for the Oracle Solaris OS at: http://support.oracle.com

If you are using the Windows operating system, install the Windows HBA driver, as described

in Chapter 4, “HBA Software Installation”.

For all other operating systems, the installation is complete.

Removing the HBA

If you need to remove the HBA from the system, follow the procedure in this section.

Chapter 2 • Hardware Installation and Removal 17

To Remove the HBA

1.

Prepare your operating system for HBA removal.

2.

Attach an antistatic wrist strap.

See “Observing ESD and Handling Precautions” on page 13.

3.

Refer to the service manual for your specific system to remove the system

cover, power down the system, and remove AC power cords from the system, if

required.

4.

Refer to the service manual for your specific system to locate the HBA in the

chassis of the system.

5.

Disengage the retention clip that secures the HBA to the chassis of the system

and pull up carefully to unseat the HBA from the PCIe slot.

6.

Detach all cables from the HBA.

7.

Refer to the service manual for your specific system to reattach the system

cover, reinstall AC power cords to the system, and power on the system, as

necessary.

18 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

3

♦ ♦ ♦ C H A P T E R 3

Creating a Bootable Drive in a Preboot

Environment

This chapter describes how to use the HBA as your boot device prior to installing an operating

system (OS) on the system.

Note - If you are installing the HBA into a system that already has an OS installed, do not

perform any tasks in this chapter. Instead, complete the HBA installation, as described in “To

Complete the Installation” on page 17.

This chapter contains the following topics:

■

“About Creating a Bootable Drive in a Preboot Environment ” on page 19

■

“Creating a Bootable Drive (SPARC)” on page 20

■

“Creating a Bootable Drive (x86)” on page 26

■

“Validating the Label of the HBA Logical Drive” on page 41

■

“Installing the Oracle Solaris OS” on page 44

■

“Next Steps” on page 45

About Creating a Bootable Drive in a Preboot Environment

As an installation option, you can choose to install the HBA into a system that does not yet have

an OS installed. With this installation option, if you plan to use the HBA as your boot device,

you can create a logical drive for the HBA to enable you to boot from the HBA. On a SPARC

system, you would perform these actions using the Preboot Command-Line Interface (pcli)

utility. On an x86 system, you would do so using the Unified Extensible Firmware Interface

(UEFI) MegaRAID Configuration menu of the BIOS Setup Utility (UEFI booting).

This section contains the following topics:

■

“Utilities Overview” on page 20

Chapter 3 • Creating a Bootable Drive in a Preboot Environment 19

Creating a Bootable Drive (SPARC)

■

“Methods for Creating a Bootable Drive” on page 20

Utilities Overview

You can specify the HBA to be your boot device by using one of these utilities:

■

pcli utility - A utility that you can run on SPARC systems. You can access this utility by

issuing a break at a remote console. This utility is an implementation of RAID commands

that you can execute from the Open Boot PROM (OBP) environment. Creating a logical

drive through the pcli utility enables the HBA to expose the drive to the system.

The command-set of the pcli utility is identical to the command-set of the storcli utility.

Therefore, to help determine the syntax and structure of the pcli commands referenced in

this chapter, review the equivalent storcli commands, as described in the MegaRAID SAS

Software User's Guide, located at: https://www.broadcom.com/support/oem/oracle/

■

LSI MegaRAID Configuration Utility menu of the BIOS Setup Utility – A utility that

you can run on an x86 system. You can access this utility by pressing F2, when prompted

during bootup, and then using the right arrow key to navigate to the Advanced tab, and then

to the LSI MegaRAID Configuration Utility menu option, near the bottom of the screen.

The MegaRAID Configuration Utility menu provides a standard environment for booting

an operating system, managing physical disks and RAID volumes, and running preboot

applications.

Methods for Creating a Bootable Drive

You must perform different procedures in this chapter, based on the type of system in which you

are installing the HBA:

■

If you are installing the HBA into a SPARC system, go to “Creating a Bootable Drive

(SPARC)” on page 20.

■

If you are installing the HBA into an x86 system, go to “Creating a Bootable Drive

(x86)” on page 26.

Creating a Bootable Drive (SPARC)

This section describes how to create or import a logical drive and then create an alias for that

drive on a SPARC system. You can then use the logical drive as your boot drive upon which to

install the Oracle Solaris OS.

20 Oracle Storage 12 Gb SAS PCIe RAID HBA, Internal: 16 Port and 2 GB Memory Installation Guide For HBA Model

7116970 • September 2017

La page charge ...

Oracle 7116970 Guide d'installation

Oracle 7116970 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents