Eaton Pulsar M 3000 RT 2U, Bundle Manuel utilisateur

www.eaton.com

Installation and User Manual

Manuel d’installation et

d’utilisation

Manual de instalación y de

usuario

Manual de instalação e do

usuário

English

Français

Español

Portuguese

EX

2200 RT 2U

2200 RT 3U

3000 RT 2U

3000 RT 3U

3000 RT 3U XL

EXB RT 3U

Pulsar Series

For Technical Support, Customer Care Center, or Customer FAQ,

please call us at (800) 356-5794, or visit our website: www.eaton.com

www.eaton.com

Installation and User Manual

EX

2200 RT 2U

2200 RT 3U

3000 RT 2U

3000 RT 3U

3000 RT 3U XL

EXB RT 3U

Pulsar Series

Introduction ....................................................................................................................... 5

Important Safety Instructions ............................................................................................ 6

Symbol Usage ................................................................................................................... 7

1. Presentation

1.1 Standard Positions ............................................................................................................. 9

1.2 Rear Panels...................................................................................................................... 10

1.3 Control Panel .................................................................................................................. 10

2. Installation

2.1 Unpacking and Contents Check ...................................................................................... 11

2.2 Installation in Tower Position ......................................................................................... 12

2.3 Installation in Rack Position ............................................................................................. 12

2.4 Communication Ports ...................................................................................................... 13

2.5 Connections with a FlexPDU (Power Distribution Unit) Module (optional) .................... 14

2.6 Connection with a HotSwap MBP Module (optional) ..................................................... 14

2.7 UPS Connection Without a FlexPDU or HotSwap MBP Module .................................... 15

3. Operation

3.1 Start-Up and Normal Operation ....................................................................................... 17

3.2 Operation on Battery Power ............................................................................................ 18

3.3 Return of AC Power ........................................................................................................ 18

3.4 UPS Shutdown ................................................................................................................ 18

3.5 Using the UPS Remote Control Functions ...................................................................... 19

4. Access to Maintenance and Personalization Data

4.1 Display Organization ........................................................................................................ 21

4.2 Access to Measurements. .............................................................................................. 21

4.3 Personalization Using the Control Panel ......................................................................... 21

4.4 Personalization Using External Software ......................................................................... 22

5. Maintenance

5.1 Troubleshooting ............................................................................................................... 23

5.2 Battery Module Replacement ......................................................................................... 24

5.3 Maintenance on a UPS Equipped With the HotSwap MBP Module .............................. 26

6. Appendices

6.1 Technical Specifications ................................................................................................. .27

6.2 Programming the Programmable Outlets ....................................................................... 28

6.3 Glossary ........................................................................................................................... 31

Contents

86-86710-00EN A02 - Page 3

86-86710-00EN A02 - Page 4

Introduction

Thank you for selecting an EATON product to protect your electrical equipment.

The EX range has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of the many features of your UPS

(Uninterruptible Power Supply).

Warning: This is a class A UPS product. In a domestic environment, this product may cause radio interference, in which

case, the user may be required to take additional measures.

If the device must be installed in overvoltage category III or IV environments, additional upstream overvoltage protection

must be provided for.

Before installing EX, please read the booklet on the required safety instructions. Then follow the indications in this

manual.

To discover the entire range of EATON products and the options available for the EX range, we invite you to visit our web

site at www.eaton.com or contact your EATON representative.

Environmental Protection

EATON has implemented an environmental-protection policy.

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing components.

w The cardboard we use comprises over 50% of recycled cardboard.

w Sacks and bags are made of polyethylene.

w Packing materials are recyclable and bear the appropriate identification symbol.

Follow all local regulations for the disposal of packing materials.

End of life

EATON will process products at the end of their service life in compliance with local regulations.

EATON works with companies in charge of collecting and eliminating our products at the end of

their service life.

w Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local regulations concerning waste.

At the end of its service life, the product must be transported to a processing centre for electrical and electronic waste.

w Battery

The product contains lead-acid batteries that must be processed according to applicable local regulations concerning

batteries.

The battery may be removed to comply with regulations and in view of correct disposal.

The «Material Safety Data Sheets» (MSDS) for the batteries are available on our web site*.

(*) For more information or to contact the Product Environmental manager, please visit our website: www.eaton.com/

pulsar.

Material Abbreviation

Symbol

number

Polyethylene terephthalate PET 01

High-density polyethylene HDPE 02

Polyvinyl chloride PVC 03

Low-density polyethylene LDPE 04

Polypropylene PP 05

Polystyrene PS 06

01

PET

01

PET

86-86710-00EN A02 - Page 5

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be followed during installa-

tion and maintenance of the UPS and batteries.

The EX models that are covered in this manual are intended for installation in an environment within 0° to 40°C (32°F to

104°F), free of conductive contaminant.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Certification Standards

w IEEE 587-1980/ANSI C62.41 1980 Standards for Surge Withstand Ability

w FCC rules and regulations of Part 15, Subpart J, Class A

w UL listed under 1778, Standards for Uninterruptible Power Supply Equipment

w IEC 61000-4-2 (ESD): level 4

w IEC 61000-4-3 (Radiated field): level 3

w IEC 61000-4-4 (EFT): level 4

w IEC 61000-4-5 (Fast transients): level 4

w IEEE-C6241 Category B (ring wave)

w IEC 61000-4-6 (electromagnetic field)

w IEC 61000-4-8 (conducted magnetic field)

Safety of Persons

w

The system has its own power source (the battery). Consequently, the power outlets may be energized even if the systems is

disconnected from the AC power source.

w

Dangerous voltage levels are present within the system. It should be opened exclusively by qualified service personnel.

w

The system must be properly grounded.

w

The battery supplied with the system contains small amounts of toxic materials. To avoid accidents, the directives listed below

must be observed:

- Never burn the battery (risk of explosion).

- Do not attempt to open the battery (the electrolyte is dangerous for the eyes and skin).

- Comply with all applicable regulations for the disposal of the battery.

-

Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be

taken for all handling: remove watches, rings, bracelets and any other metal objects, use tools with insulated handles.

- Do not lay tools or metal parts on top of batteries.

Product Safety

w

The UPS connection instructions and operation described in the manual must be followed in the indicated order.

w

A protection circuit breaker must be installed upstream and be easily accessible. The system can be disconnected from the AC

power source by opening this circuit breaker.

w

Check that the indications on the rating plate correspond to your AC powered system and to the actual electrical consumption of

all the equipment to be connected to the system.

w

The socket-outlet shall be installed near the equipment and shall be easily accessible.

w

Never install the system near liquids or in an excessively damp environment.

w

Never let a foreign body penetrate inside the system.

w

Never block the ventilation grates of the system.

w

Never expose the system to direct sunlight or source of heat.

w

If the system must be stored prior to installation, storage must be in a dry place.

w

The admissible storage temperature range is -20ºC to +40ºC (-4

°F to 104°F).

w

The maximum operating temperature without power derating is 40

°C (104°F).

Special Precautions

w

All handling operations will require at least two people (unpacking, installation in rack system).

w

Before and after the installation, if the UPS remains de-energized for a long period, the UPS must be energized for a period of

24 hours, at least once every 6 months (for a normal storage temperature less than 25°C (77

°F)

). This charges the battery, thus

avoiding possible irreversible damage.

w

During the replacement of the Battery Module, it is imperative to use the same type and number of element as the original Battery

Module provided with the UPS to maintain an identical level of performance and safety. In case of doubt, don’t hesitate to contact

your EATON representative.

Environment

w

This product has been designed to respect the environment:

It does not contain any Chlorofluorocarbon (CFC) or Hydrochlorofluorocarbon (HCFC).

w

UPS recycling at the end of service life:

EATON undertakes to recycle, by certified companies and in compliance with all applicable regulations, all UPS products

recovered at the end of their service life (contact your EATON branch office).

w

Packing: UPS packing materials must be recycled in compliance with all applicable regulations.

WARNING: This product contains lead-acid batteries. Lead is a dangerous substance for the environment if it is not

properly recycled by specialized companies.

86-86710-00EN A02 - Page 6

Symbol Usage

Important instructions that must always be followed.

Information, advice, help.

Visual indication.

Action.

Audible signal.

LED off.

LED on.

LED flashing.

86-86710-00EN A02 - Page 7

86-86710-00EN A02 - Page 8

1. Presentation

1.1 Standard Positions

Tower Position

Rack Position

Dimensions (H x W x D) in inches

EX 2200 RT 2U 17.3 x 3.38 x 25.2

EX 2200 RT 3U 17.3 x 5.16 x 19.3

EX 3000 RT 2U 17.3 x 3.38 x 25.2

EX 3000 RT 3U 17.3 x 5.16 x 19.3

EX 3000 RT 3U XL 17.3 x 5.16 x 19.3

EX EXB RT 3U 17.3 x 5.16 x 19.3

Weight in pounds

EX 2200 RT 2U 70

EX 2200 RT 3U 68

EX 3000 RT 2U 72

EX 3000 RT 3U 70

EX 3000 RT 3U XL 41

EX EXB RT 3U 93

Part Numbers

EX 2200 RT 2U 86722

EX 2200 RT 3U 86723

EX 3000 RT 2U 86732

EX 3000 RT 3U 86733

EX 3000 RT 3U XL 86735

EX EXB RT 3U 68405

86-86710-00EN A02 - Page 9

1.2 Rear Panels

EX 2200 / 3000 / 3000 XL

EX EXB (optional battery module)

12 12

13

1.3 Control Panel

(1) USB communication port

(2) RS232 communication port

(3) Connector for automatic recognition of an

additional battery module

(4) Slot for optional communication card

(5) Connector for remote ON/OFF and RPO

(Remote Power Off) control

(6) Connector for additional battery module

(7) L5-20R (or L5-30R for EX 3000) receptacle

for connection of equipment

(8) 2 programmable outlets for connection of

equipment

(9) Groups of 4 outlets for connection of

equipment

(10) 10-foot input power cord

w L5-30P for EX 3000

w 5-20P for EX 2200

(11) LED (SWF) indicating distribution system

phase/neutral reversal

(12) Connectors for battery modules (to the

UPS or to the other battery modules)

(13) Connectors for automatic recognition of

battery modules

(20) Load protected LED

(21) Downgraded operation LED

(22) Load not protected LED

(23) LCD

(24) Escape (cancel) button

(25) Scroll button

(26) Enter (confirm) button

(27) ON/OFF button for UPS and outlets

EX 2200

86-86710-00EN A02 - Page 10

1. Presentation

2. Installation

2.1 Unpacking and Contents Check

Packing materials must be disposed of in compliance with all local regulations concerning waste.

Recycling symbols are printed on the packing materials to facilitate sorting.

(30) EX 2200 or 3000 UPS

(33) RS232 communications cable

(34) USB communications cable

(36) Solution-Pac CD-ROM

(37) Documentations supplied depending on the UPS

model

(38) Mounting kit for 19-inch bays, except for RT 3U

models

(39) 2 supports for the upright position (2U version

only)

(40) FlexPDU module (optional)

(42) NMC communication card (optional)

(43) HotSwap MBP module (optional)

86-86710-00EN A02 - Page 11

2.2 Installation in Tower Position

2.3 Installation in Rack Position

It is advised to first install the battery module, then the power module above.

Follow steps 1 to 4 for module mounting on the rails.

The rails and necessary hardware are supplied, except for 3U models, by EATON.

86-86710-00EN A02 - Page 12

2. Installation

2.4 Communication Ports

Connection of RS232 or USB communication port (optional)

The RS232 and USB communication ports cannot operate simultaneously.

Installation of the communication cards (optional)

1. Connect the RS232 (33) or USB (34)

communication cable to the serial or USB

port on the computer equipment.

2. Connect the other end of the communica-

tion cable (33) or (34) to the USB (1) or

RS232 (2) communication port on the UPS.

The UPS can now communicate with

EATON power management software.

It is not necessary to shutdown the UPS

before installing a communications card.

1. Remove the UPS cover (4) secured by

screws.

2. Insert the communications card in the slot.

3. Secure the card with screws.

Communication card slot

(restricted access)

86-86710-00EN A02 - Page 13

2. Installation

2.5 Connections with a FlexPDU (Power Distribution Unit) Module (optional)

2.6 Connections with a HotSwap MBP Module (optional)

The HotSwap MBP module makes it possible to service or even replace the UPS without affecting the connected

loads (HotSwap function).

1. Connect the UPS powercord (10) to the AC

power source.

2. Connect the input cord of the FlexPDU

module (48) to the UPS outlet (9). The cord

and the outlet are marked in red.

3. Connect the equipment to the outlets (45),

(46) on the FlexPDU module. These outlets

differ, depending on the version of the

FlexPDU module.

EX 3000

1. Connect the input cord (56) of the

HotSwap MBP module to the AC power

source.

2. Connect the UPS input cord (10) to the

“UPS Input” (55) of the HotSwap MBP

module. This cord and the receptacle are

marked blue.

3. Connect the UPS outlet (7) to the “UPS

Output” cord (54) of the HotSwap MBP

module. This cord and the outlet are

marked red.

4. Connect the equipment to the outlets (49)

on the HotSwap MBP module.

Caution:

Do not use UPS outlets (8)and (9) to

supply equipment because use of switch

(53) on the HotSwap MBP module would

cut supply to the equipment. It is advised

not to remove the protective film from

outlets (8) and (9).

86-86710-00EN A02 - Page 14

2. Installation

HotSwap MBP module operation

UPS start-up with the HotSwap MBP module

1. Check that the UPS is correctly connected to the HotSwap MBP module.

2. Set switch (53) to the Normal position.

3. Start the UPS by pressing the ON/OFF button (27) on the UPS control panel.

The load is supplied by the UPS.

LED (51) “UPS ON - OK to switch” on the HotSwap MBP module goes ON.

HotSwap MBP module test

1. Set switch (53) to the Bypass position and check that the load is still supplied.

2. Set switch (53) back to the Normal position.

2.7 UPS Connection Without a FlexPDU or HotSwap MBP Module

Check that the indications on the name plate located on the back of the UPS correspond to the AC power source

and the true electrical consumption of the total load.

i

Note: The UPS charges the battery as soon as it is connected to the AC power source, even if button (27) is not

pressed. Once the UPS is connected to the AC power source, eight hours of charging are required before the

battery can supply the rated backup time

i

The HotSwap MBP module has a rotary

switch (53) with two positions:

Normal – the load is supplied by the UPS,

LED (51) is ON.

Bypass – the load is supplied directly by

the AC power source. LED (52) is

ON.

1. Connect the input cord (31) (120V 30A / or

20A on EX 2200) to the AC power source.

2. Connect the loads to the UPS.

It is preferable to connect the priority loads

to the four outlets marked (9) and the

non-priority loads to the two outlets

marked (8) that can be programmed.

Connect any high-power devices to the

20A (or 30A on EX 3000) outlet (7) as

shown at left for EX 2200.

To program shutdown of outlets (8)

during operation on battery power and

thus optimise the available backup time,

the EATON communications software is

required.

86-86710-00EN A02 - Page 15

2. Installation

(This page left blank intentionally)

86-86710-00EN A02 - Page 16

3. Operation

3.1 Start-Up and Normal Operation

i

For the initial start-up, AC power must be present to detect any wiring errors. After inital start-up, the UPS can

start even if AC power is not present.

UPS personalization

i

If UPS personalization is desired, it is advised to enter the personalization mode at this time.

This mode may be entered using the buttons on the control panel or the Personal Solution-Pac Software (Windows)

included on the Solution-Pac CD-ROM provided by EATON.

Press button (27) for approximately 1 second.

w The buzzer beeps once and all the LEDs go

ON simultaneously.

w The buzzer then beeps twice during the

self-test, then button (27) remains ON,

indicating power to the output receptacles.

The connected devices are protected by

the UPS.

w LED (20) is ON.

If LED (22) is ON, a fault has occurred (see

the “Troubleshooting” section).

w During normal operation, the scroll

button (25) may be used to read UPS

measurements (voltage on normal and

bypass AC inputs, operating mode, battery

capacity and UPS serial number).

86-86710-00EN A02 - Page 17

3.2 Operation on Battery Power

Transfer to battery power

Low-battery warning

Low on battery power

20

End of battery backup time

w All the LEDs go OFF.

w The audio alarms stop.

i

The UPS is completely shut down

3.3 Return of AC power

Following an outage, the UPS restarts automatically when AC power returns (unless the restart function was

disabled via UPS personalization) and the load is again supplied.

3.4 UPS shutdown

Press button (27) for approximately 2 seconds.

The devices connected to the UPS are no longer

supplied.

w The connected devices continue to be

supplied by the UPS when AC power is no

longer available. The necessary energy is

provided by the battery.

w LEDs (20) and (21) go ON.

w The audio alarm beeps every ten seconds.

The connected devices are supplied by

the battery. The display indicates the

remaining backup time.

w LEDs (20) and (21) go ON.

w The audio alarm beeps every three

seconds.

The remaining battery power is low.

Shut down all applications on the

connected equipment because automatic

UPS shutdown is imminent.

86-86710-00EN A02 - Page 18

3. Operation

La page charge ...

Eaton Pulsar M 3000 RT 2U, Bundle Manuel utilisateur

Ce manuel convient également à

Eaton Pulsar M 3000 RT 2U, Bundle Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents