Yamaha PLG150 Le manuel du propriétaire

Marque: Yamaha

Modèle: PLG150

Catégorie: Instruments de musique

Taper: Le manuel du propriétaire

Ce manuel convient également à

PLG150-AN

AN Expert Editor

Manual

Important Notices

The AN Expert Editor provides an easy, intuitive way to edit and create your own original

AN voices for the PLG150-AN Plug-in Board.

Do not use any of the panel controls on an external synthesizer while editing the AN

voices with the AN Expert Editor, since this may inadvertently change the settings of the

PLG150-AN.

• The software and this owner’s manual are the exclusive copyrights of Yamaha Corpora-

tion.

• Copying of the software or reproduction of this manual in whole or in part by any

means is expressly forbidden without the written consent of the manufacturer.

• Copying of the commercially available music sequence data and/or digital audio ﬁles is

strictly prohibited except for your personal use.

Trade Marks and Registered Trade Marks

• The company names and product names in this Owner’s Manual are the trademarks or

registered trademarks of their respective companies.

Notices

• Yamaha makes no representations or warranties with regard to the use of the software

and documentation and cannot be held responsible for the results of the use of this

manual and the software.

• The windows and illustrations in this manual are for instructional purposes only, and

may slightly different from the ones shown on your software.

About this manual

• The screens shown in this manual are almost all on Windows systems. Although some

screens may differ for Macintosh systems, the basic operations are the same.

• Keyboard shortcuts referred in this manual are effective for only Windows system.

For Windows users

When you use the AN Expert Editor, set “Font Size” to “Small Fonts” at the “Control Panel | Display | (Settings |)

Advanced” page. If “Large Fonts” is selected, messages in some dialog boxes may not be displayed properly.

Version 1.1, 2002

YAMAHA CORPORATION

About the AN Expert Editor

The AN Expert Editor is providing an exceptionally simple, convenient and intuitive way

to edit and control all of the AN parameters on the PLG150-AN Plug-in Board. Virtual

“knobs,” “buttons” and a special “LCD display” let you change parameters just as if you

were operating an actual synthesizer control panel!

The AN Expert Editor lets you save your edits as an original User voice and store up to

128 User voices and User Step Sequencer patterns. Naturally, you can save the data

to ﬂoppy disks or your hard disk drive as AN Expert Files. The AN Expert Editor also

features a convenient, easy-to-use AN Librarian that lets you organize your User voices.

Editing on the AN Expert Editor is done from the Main Window.

For general instructions and explanations on how to use the AN Expert Editor, see Set-

ting and Changing Parameter Values and Toolbar. For information on speciﬁc, com-

monly used operations, see Operations.

Operations

• The following information pertains only to the Plug-in Editor.

In order to play and edit the PLG150-AN, the AN voice must be assigned to a Part on

the tone generator/sound card. This can be done from two separate menus on the AN

Expert Editor: the initial Select AN Part Pop-up Menu (which appears automatically

whenever you start the AN Expert Editor) and AN Expert Editor Setup.

■

Select AN Part Pop-up Menu.......................................

• [Cancel] button may not be available depending on the editor you use.

Select the desired Part.

The Select AN Part pop-up menu appears when you ﬁrst call up the AN Expert Edi-

tor. Select the desired Part from the Part combo box.

• When using a Modular Synthesis Plug-in System “mother” device, the Part assignment

depends on which mode is used — Voice or Performance — and also on whether the PLG150-

AN board is installed/assigned to PLG1 or PLG2, as described below.

When using the Voice mode:

Set the Part to “1” (no matter what the PLG1 or PLG2 assignment is).

When using the Performance (Multi) mode:

If the PLG150-AN board is assigned to PLG1, set the Part to “16.”

If the PLG150-AN board is assigned to PLG2, set the Part to “15.”

Click “OK.”

• Click “Details” to call up the AN Expert Editor Setup menu for making more detailed settings.

Assigning the PLG150-AN to a Part

Operations /

Assigning the PLG150-AN to a Part

■

Using the AN Expert Editor Setup..............................

Even after you’ve set the AN Part from the pop-up menu, you can change the setting

during an editing session from the AN Expert Editor Setup dialog box.

Select “AN Expert Editor Setup.”

While the AN Expert Editor is active and selected, click “Setup” on the menu bar,

then select “AN Expert Editor Setup.” (Keyboard shortcut: [Alt], [U], [U], then

[ENTER].)

• “AN Expert Editor Setup” can also be selected from the toolbar.

Select the desired Part.

Do this from the Part No. combo box in the MIDI tab. Make other settings if neces-

sary. (See AN Expert Editor Setup.)

Click “OK.”

Operations /

Selecting an AN Voice

Selecting an AN voice is the important ﬁrst step in editing. You can select a voice from

Preset 1, Preset 2, or User banks (each of which contains 128 voices). Once you’ve

edited a voice you can store it to the User bank as your original voice and save it to a

ﬂoppy disk/hard disk drive with other voices as an AN Expert File.

AN voices can be selected from either the Edit Panel window or the main control panel

window.

• Make sure to store your edits to a voice before selecting another voice. If you’ve edited the

AN Expert Editor parameters and then select a different voice, all your edited parameters will

be initialized to the default values of the newly selected voice.

Select “AN Voice List.”

Click the VOICE button at the bottom right of the main control panel.

You can also quickly call up this dialog box by right-clicking any inactive part of the

window (on the Macintosh, click while holding the CONTROL key) and clicking “AN

Voice List” in the pop-up menu. Or, you can click “Edit” on the menu bar, then

select “AN Voice List.” (Keyboard shortcut: [Alt], [E], [V].)

Select the desired voice.

Click on the desired voice, then close the dialog box (click the close button) to

return to the main control panel window. (You can also do this by clicking anywhere

on the main control panel.)

Selecting an AN Voice

Operations /

Editing an AN Voice

Select the desired voice.

Refer to Selecting an AN Voice.

Edit the voice parameters as desired from the main control

panel.

The main window of the AN Expert Editor provides a “virtual” control panel with

knobs and buttons, and lets you edit the voices much as you would if you were

operating an actual hardware synthesizer.

Store the edited settings as a User voice, then save it with other

edited voices as an AN Expert File.

Use the Store operation to store your newly edited voice. Then use the Save oper-

ation to save that edited voice with other User voices to an AN Expert File.

Both the Store and Save operations are necessary to ensure that your voice is

saved properly. Failing to do so would be roughly similar to writing a letter but not

putting it in an envelope and sending it. Make sure to execute both operations

when you wish to keep a voice you’ve edited.

Editing an AN Voice

Operations /

Initializing an AN Voice to the Default Settings

This function allows you to reset all the parameters of the selected voice to the factory

“initial voice” default values. This gives you a “blank slate” from which you can create

your own voice.

Keep in mind that this operation automatically erases all the settings of the selected

voice. If you wish to save the voice for future recall, use the Store and Save functions.

Select “AN Voice List.”

Click the VOICE button at the bottom right of the main control panel.

You can also quickly call up this dialog box by right-clicking any inactive part of the

window (on the Macintosh, click while holding the CONTROL key) and clicking “AN

Voice List” in the pop-up menu. Or, you can click “Edit” on the menu bar, then

select “AN Voice List.” (Keyboard shortcut: [Alt], [E], [V].)

Select the User bank and the desired voice to be initialized.

Click on the User bank button, then click on the desired voice.

Initialize the voice.

Click the “Voice Init” button in the dialog box. The speciﬁed voice is initialized and

automatically selected for editing.

To return to the main control panel window, close the dialog box (click the close but-

ton). (You can also do this by clicking anywhere on the main control panel.)

• If you want to initialize all User voices, then click on the “INIT ALL” button in the AN Librarian

window.

Initializing an AN Voice to the Default Settings

Operations /

Storing an AN Voice

This operation lets you store your voice edits as a User voice.

• To ensure that your new voice is available for future recall, make sure to also save the voice

(with other voices) to an AN Expert File.

Select “AN Store.”

Click the red STORE button at the bottom right of the main control panel.

You can also quickly call up this dialog box by right-clicking any inactive part of the

window (on the Macintosh, click while holding the CONTROL key) and clicking “AN

Store” in the pop-up menu. Or, click “Edit” on the menu bar, then select “AN Store.”

(Keyboard shortcut: [Alt], [E], [S].)

Select the destination voice.

Click on the desired voice in the dialog box. Keep in mind that this voice will be

erased and replaced with the newly edited voice.

Store the voice.

Click the “Store” button in the dialog box. The newly edited voice is stored to the

selected location.

• This operation deletes the original voice data at the destination.

• Keep in mind that this operation stores your voice data only into the User voice memory of

the AN Expert Editor and sends the current voice’s bulk data to the PLG150-AN. The current

voice bulk data will be lost if you select another voice on the panel of the plug-in “mother”

device. If you want to select a voice on the panel of the “mother” device, you should ﬁrst

transmit the User Voice. (Refer to Transmit AN Bulk Dump Data in the AN Expert Editor Setup,

Insert & Transmit tab.) There is no need to transmit AN Bulk Dump Data if you select a voice

in the Voice List of the AN Expert Editor, since the current voice bulk data is sent with that

operation.

• The User voice data of the PLG150-AN is lost when the “mother” device is turned off. In order

to store User voices on a Modular Synthesis Plug-in System compatible instrument that have

been edited/created with the computer-based AN Expert Editor (or with the compatible instru-

ment itself), you’ll need to use an external memory device, such as a memory card. For

details on storing voices, refer to the owner’s manual of your Modular Synthesis Plug-in Sys-

tem compatible instrument.

Storing an AN Voice

Operations /

Saving data to an AN Expert File

Calling Up data from an AN Expert File (Open)

Once you’ve edited an AN voice and pattern to your satisfaction you can save it to an

AN Expert File. Each AN Expert File can contain up to 128 voices and 128 Step

Sequencer patterns, and these can be called up at any time with the Open function.

(Also see Calling Up data from an AN Expert File.)

Additional AN Expert ﬁles (each with 128 User voices and 128 User Step Sequencer

patterns) can be saved to ﬂoppy disks or your hard disk drive --- giving you unlimited

storage for your original voices. For organizing the voices in the AN Expert Files, use

the convenient AN Librarian function.

Select “Save AN Expert File.”

Click “File” on the menu bar, then select “Save AN Expert File.” (Keyboard shortcut:

[Alt], [F], [W].)

• “Save AN Expert File” can also be selected from the toolbar.

Select the desired folder, type in the ﬁle name, and click “Save.”

Once you’ve saved a set of User voices and User Step Sequencer patterns to one or

more AN Expert Files (see Saving Voices), you can instantly call up the desired voices

with this command.

To create a new AN Expert File, use the New AN Expert File command.

Select “Open AN Expert File.”

Click “File” on the menu bar, then select “Open AN Expert File.” (Keyboard short-

cut: [Alt], [F], [R].) Open AN Expert File is also available on the toolbar.

Select the desired folder and ﬁle name, then click “Open.”

• Keep in mind that this operation loads the User voice and Step Sequencer pattern data only

into the User voice memory of the AN Expert Editor. After opening a ﬁle, if you want to play

with these Voices or Step Sequencer patterns separate from the AN Expert Editor, you should

transmit the User voice or Step Sequencer pattern data. (Refer to Transmit AN Bulk Dump

Data in the AN Expert Editor Setup, Insert & Transmit tab.) There is no need to transmit AN

Bulk Dump Data if you select a voice in the Voice List of the AN Expert Editor, since the cur-

rent voice bulk data is sent with that operation.

Saving data to an AN Expert File

Calling Up data from an AN Expert File (Open)

Operations /

Inserting Edited Voice Data to a Track

• The following information pertains only to the Plug-in Editor.

User voice (or User Step Sequencer pattern) data can be inserted to a host applica-

tion's track (using Insert AN Bulk Dump Data). By inserting appropriate data at appro-

priate points in the song, you can have the AN voices change automatically as needed.

Select “AN Expert Editor Setup.”

Click “Setup” on the menu bar, then select “AN Expert Editor Setup.” (Keyboard

shortcut: [Alt], [U], [U], [ENTER].)

• “AN Expert Editor Setup” can also be selected from the toolbar.

Select the “Insert & Transmit” tab.

Click on the desired settings.

Click “OK.”

Select “Insert AN Bulk Dump Data” from the Setup menu (key-

board shortcut: [Alt], [U], [I]), or from the toolbar.

Set the location (Track, Measure, Beat, and Clock).

Click “OK.”

By using the Insert and Extract functions together, you can record and recall your edits as

needed — giving you an unlimited amount of “undos.” For each major edit, use Insert to save

the edited condition to a section of a track (inserting each edit to subsequent sections of the

same track). Then, to recall any given edit, use the Extract function and select the appropriate

range of measures.

Inserting Edited Voice Data to a Track

Operations /

Using the Morphing Function

This exceptionally powerful function allows you to use any MIDI controller (such as a

modulation wheel, foot controller, or after touch) to “morph” or crossfade between two

distinct voices — in real time as you play! Naturally, you can record controller data to a

sequencer for automated morphing within a song as well. This lets you create dramatic

or subtle sonic changes in your performance or song.

• The AN Morphing settings apply to all voices for the AN Expert Editor, and cannot be set inde-

pendently for each voice (this includes the MORPH switch).

Select “AN Morphing.”

Click “Setup” on the menu bar, then select “AN Morphing.” (Keyboard shortcut:

[Alt], [U], [P].)

• “AN Morphing” can also be selected from the toolbar.

Select the desired MIDI controller.

Do this from the “Morphing Controller” combo box. After touch (AT) or any one of

the 95 control change numbers can be selected. For example, if controller #1 is

speciﬁed here, the modulation wheel on a MIDI keyboard can be used to morph

between the two voices.

• The particular MIDI controller and its actual number assignment may depend on settings

made to the connected MIDI instrument; see the relevant owner’s manual for details. Also,

refer to the list of control change numbers and their commonly used controllers.

Select the desired voice for Morphing.

Using the Morphing Function

Operations /

Recording Within the AN Expert Editor

To do this:

1) Specify a bank by clicking on the desired bank button: Preset 1, Preset 2, or

User.

2) Click on the voice combo box and select the desired voice. For a complete list

of available voices, see the Voice List in the PLG150-AN Owner’s Manual.

• Each voice name is preceded by a two-letter category abbreviation that indicates the general

instrument group to which the voice belongs. For example, “Ld” indicates “lead,” “Ba” indi-

cates “bass,” “Pd” indicates “pad,” and so on. For details, see the Voice List in the PLG150-

AN Owner’s Manual.

Turn on the MORPH switch on the AN Expert Editor’s control

panel.

Use the appropriate controller (modulation wheel, after touch,

foot controller, etc.) while you play, to morph between the two

voices.

• The following information pertains only to the Plug-in Editor.

• Depending on your particular host application, certain operation steps may differ and/or

some functions may not be available.

This powerful and convenient function allows you to record continuous edits to the AN

voice in real time. For example, if you’ve recorded note data to one track in host appli-

cation, you can use the AN Expert Editor to create gradual, dynamic changes in the

track with any of the AN Expert Editor parameters. These changes can be saved with

the song and can be played back exactly as you recorded them.

Select “AN Expert Editor Setup.”

Click “Setup” on the menu bar, then select “AN Expert Editor Setup.” (Keyboard

shortcut: [Alt], [U], [U], [ENTER].)

• “AN Expert Editor Setup” can also be selected from the toolbar.

Select the desired track for recording.

Do this from the “REC Track” combo box in the MIDI tab. For most practical pur-

poses, this track should be one to which you have already recorded note data and

intended for use with an AN voice. Note that you can record the track without hav-

ing to go to the Track View window in host application and enable it.

Recording Within the AN Expert Editor

Operations /

Recording Within the AN Expert Editor

Click “OK.”

Set recording-standby.

Click “Edit” on the menu bar, then select “Record.” Alternately, click on the Record

button in the toolbar.

Start recording on the host applications.

Edit the AN parameters as desired.

Any edits you make within the AN Expert Editor are recorded in real time, as you

make them. You can even record voice changes in real time.

Stop recording on the host applications.

Exit from recording-standby.

Click “Edit” on the menu bar, then select “Record.” Alternately, click on the Record

button in the toolbar.

Play back the song.

Use the Play Control window to return to the beginning of the track and start play-

back. Further edits can be recorded (overdubbed) to the same track by re-selecting

the AN Expert Editor window and repeating steps #4 - #8 above.

• If you’re not satisﬁed with the recorded result, the last recording you’ve done can be canceled

using the Undo function in the Edit menu (keyboard shortcut: Ctrl + Z).

Parameters

Most of the AN Expert Editor parameters for editing the AN voices are contained in the

virtual “main control panel” screen. From this main panel, you can also jump to other

windows for controlling additional PLG150-AN functions (such as the Control Matrix,

Free EG, and Pattern Generator).

This is the main control panel for the AN Expert Editor, and is comprised of the virtual

“panel” controls, the toolbar (at the top), and the virtual “LCD display” at the bottom.

• Main Screen

• Master Menu

The master menu (which includes AN Voice List, Store, and the Display Option) can be

selected from the main screen by right-clicking any inactive part of the front panel (on

the Macintosh, click while holding the CONTROL key).

AN Expert Editor Main Window

Parameters / AN Expert Editor Main Window

• Toolbar

The toolbar gives you quick access to some important functions and controls. These

buttons let you easily execute the desired function without having to select a menu or

leave the AN Expert Editor window.

Open AN Expert File

This is the same as the corresponding command in the File menu. It lets you select and

open an existing AN Expert File. (See File Menus, Open AN Expert File.)

Save AN Expert File

This is the same as the corresponding command in the File menu. It lets you save the

current AN Expert Editor settings as a parameter ﬁle for future recall. (See File Menus,

Save AN Expert File.)

AN Expert Editor Setup

This is the same as the corresponding command in the Setup menu. It lets you make

various important settings for conﬁguring the AN Expert Editor with the PLG150-AN.

(See Setup Menus, AN Expert Editor Setup.)

Setup AN Display Option

This convenient feature lets you change the display of the main control panel to indicate

the current status of certain signal routings within the PLG150-AN. (See Setup Menus,

AN Display Option.)

Setup AN Morphing

This is the same as the corresponding command in the Setup menu. It lets you make the

appropriate settings for the Morphing function (selecting the MIDI controller and the Mor-

phing voice). (See Setup Menus, AN Morphing.)

Insert AN Bulk Dump Data (Plug-in Editor only)

This is the same as the corresponding command in the Setup menu. It lets you insert the

current AN Expert Editor settings to a speciﬁed track/position in the host application

song. (See Setup Menus, Insert AN Bulk Dump Data.)

Parameters / AN Expert Editor Main Window

Transmit AN Bulk Dump Data

This is the same as the corresponding command in the Setup menu. It lets you transmit

the current AN Expert Editor settings as MIDI data to the PLG150-AN board. (See Setup

Menus, Transmit AN Bulk Dump Data.)

Extract AN Bulk Dump Data (Plug-in Editor only)

This is the same as the corresponding command in the Setup menu. It lets you import

the bulk data of AN voice or Step Sequencer patterns in the sequenced song data to the

AN Expert Editor. (See Setup Menus, Extract AN Bulk Dump Data.)

Receive AN1x Bulk Dump Data

This is the same as the corresponding command in the Setup menu. It lets you receive

the voice or Step Sequencer settings from a connected AN1x Control Synthesizer as

MIDI data. (See Setup Menus, Receive AN1x Bulk Dump Data.)

Record (Plug-in Editor only)

This allows you to record your edit moves to a track, creating dynamic changes in the AN

voice as the song plays. (See Recording Within the AN Expert Editor.)

• Depending on your particular host application, certain operation steps may differ and/or this

function may not be available.

• LCD Display

This virtual “LCD” functions just like the display on an actual synthesizer’s front panel.

Indicates the current voice’s bank/number

as well as its category and name.

Full name of the currently

selected parameter.

Indicates the currently selected parameter’s value or setting.

By clicking on this third line, you can also directly change the

value by typing it on the computer keyboard. (See Computer

keyboard.)

Parameters / AN Expert Editor Main Window

• VOICE Button

Pressing the VOICE button calls up the AN Voice List dialog box, allowing you to select

the desired voice bank and voice. It also allows you to reorganize the voices of a

selected bank, as well as initialize a voice --- in other words, this resets all parameters

to their normal values, giving you a “blank slate” voice to work with.

To select a bank, click on the desired bank button: Preset 1, Preset 2, or User. Each

bank contains 128 voices. To select a voice, click on the desired voice in the box. For

a complete list of available voices, see the Voice List in the PLG150-AN Owner’s Man-

ual.

• Each voice name is preceded by a two-letter category abbreviation that indicates the general

instrument group to which the voice belongs. For example, “Ld” indicates “lead,” “Ba” indi-

cates “bass,” “Pd” indicates “pad,” and so on.

Parameters / AN Expert Editor Main Window

• STORE Button

Pressing the STORE button calls up the AN Store dialog box, allowing you to store the

desired voice to the User bank. It also lets you enter a name and category abbrevia-

tion for the voice.

To name the voice, click on the Voice Name box, and type in the desired name. To

specify a category, click the Category combo box, and click the desired category

abbreviation. (The “0: ---” setting indicates no category.) To store the newly named

voice, click “Store.” For a complete list of available voices and descriptions of the cate-

gory abbreviations, see the Voice List in the PLG150-AN Owner’s Manual.

• Each voice name is preceded by a two-letter category abbreviation that indicates the general

instrument group to which the voice belongs. For example, “Ld” indicates “lead,” “Ba” indi-

cates “bass,” “Pd” indicates “pad,” and so on.

Parameters / AN Expert Editor Main Window

■ Setting and Changing Parameter Values ...................

• For panel knobs:

Left-click on the knob and drag horizontally or vertically as desired. Dragging to the left

or down decreases the value, and dragging right or up increases it. The knob “rotates” as

you drag it, and the parameter value (shown just above each knob) changes accordingly.

Any parameter changes are output as MIDI data, both to the PLG150-AN and the host

application (for recording).

Operation of the knobs can also be set so that moving the mouse in a circular direction

— as if you were actually rotating the knob — changes the parameter value. (See

Parameter Knob Operation.)

• The panel knob operation can be changed to let you “rotate” the knob, instead of moving it

horizontally or vertically. (See the Others tab in AN Expert Editor Setup.)

• For buttons:

Simply left-click on the desired button to turn on/off or to select the appropriate setting.

On/off buttons (such as MORPH) have virtual “lamps” that light when the function is on.

• Combo boxes

For combo boxes (such as Control Source in the Control Matrix Parameter tab), click the

down arrow to expand the box, then highlight the desired setting.

• DATA DEC (Decrease) and INC (Increase) buttons

Click on the desired parameter, then click either of these buttons to decrease the value/

setting (DEC) or increase it (INC). These buttons in some cases (e.g., VCO 1 WAVE) can

be used to select values/settings that are not available otherwise>

Parameters / AN Expert Editor Main Window

• Mouse buttons

A few parameters (such as Unison Detune and LFO 1 Delay in the Detail Parameters

tab) can be adjusted with the mouse buttons. Click on the desired parameter, then click

the left mouse button to decrease the value or click the right mouse button to increase it.

• Computer keyboard

All of the value parameters can be directly changed by typing in the appropriate numbers

from the computer keyboard. Click on the desired parameter, then click the third (bottom)

line in the virtual LCD and type in the desired value. Press [ENTER] to enter the value.

A few parameters (such as Unison Detune and LFO 1 Delay in the Detail Parameters

tab) can be directly changed by clicking on the desired parameter, then typing in the

desired value.

• Computer keyboard shortcuts:

• Moving around the panel

Pressing the arrow keys by themselves lets you select parameters by moving around

the panel in the respective direction (up, down, left, right).

• Rapidly adjusting values

You can also use the arrow keys to adjust the parameter values. Simultaneously hold

down [SHIFT] and press or hold one of the arrow keys. The up or right keys increase

the value while the down or left keys decrease it. Holding down [SHIFT] and the

appropriate arrow key rapidly increases or decreases the value.

The Page Up and Page Down keys on the computer keyboard can also be used.

Press Page Up to increase the value, and Page Down to decrease it. Hold down the

appropriate button to rapidly increase or decrease the value.

• Value charts

A few parameters (such as VCF Velocity) have pop-up “value charts,” from which you can

select the desired value. Simply left-click on the parameter’s button, highlight the desired

value, then left click on the value.

La page charge ...

Yamaha PLG150 Le manuel du propriétaire

Marque: Yamaha

Modèle: PLG150

Catégorie: Instruments de musique

Taper: Le manuel du propriétaire

Ce manuel convient également à

PLG150-AN

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha PLG150 Manuale del proprietario
English: Yamaha PLG150 Owner's manual
español: Yamaha PLG150 El manual del propietario
Deutsch: Yamaha PLG150 Bedienungsanleitung
русский: Yamaha PLG150 Инструкция по применению
Nederlands: Yamaha PLG150 de handleiding
português: Yamaha PLG150 Manual do proprietário
dansk: Yamaha PLG150 Brugervejledning
polski: Yamaha PLG150 Instrukcja obsługi
čeština: Yamaha PLG150 Návod k obsluze
svenska: Yamaha PLG150 Bruksanvisning
Türkçe: Yamaha PLG150 El kitabı
suomi: Yamaha PLG150 Omistajan opas
română: Yamaha PLG150 Manualul proprietarului

Yamaha PLG150 Le manuel du propriétaire

Ce manuel convient également à

Yamaha PLG150 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents