Danby DKC052BSLDB-D Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
Model • Modèle • Modelo
2015.06.03
Owners Use and Care Guide
Guide d’utilisation et d'entretien
Manual de instrucciones
KEG COOLER
GLACIÈRE DE BIÈRE PRESSION
BARRIL REFRIGERADOR
DKC052BSLDB-D
Danby Products Limited, Ontario, Canada N1H 6Z9
Danby Products Inc., Findlay, Ohio, USA 45840
DO NOT RETURN THIS UNIT TO THE RETAILER
WITHOUT FURTHER INSTRUCTIONS
Dear valued customer, we hope your Danby product purchase fulfills all
your requirements. Your satisfaction is our priority!
Please contact us at our toll free consumer service number for any inquiries
you may have about your new unit.
NE PAS RETOURNER CET APPAREIL CHEZ LE
DÉTAILLANT SANS CONSIGNES SUPPLÉMENTAIRES
Cher(ère) client(e) important(e), nous espérons que votre produit Danby
répond à tous vos besoins. Votre satisfaction est notre priorité!
Veuillez nous contacter au numéro gratuit de service après-vente, si
vous avez des questions quelconques à propos de votre nouvel appareil.
NO DEVUELVA ESTA UNIDAD A LA TIENDA SIN
INSTRUCCIONES ADICIONALES
Estimado cliente, esperamos que el producto Danby que ha comprado
satisfaga completamente sus necesidades. Su satisfacción
es nuestra prioridad!
Por favor, contáctenos gratuitamente a nuestro número de Servicio al
Cliente para cualquier pregunta que tenga sobre su nuevo electrodoméstico.
1-800-263-2629
(1-800-26-DANBY)
Danby 28.08.2014
GLACIÈRE DE BIÈRE PRESSION
Guide d'utilisation et d'entretien
Consignes de sécurité importantes ....................
Caractéristiques ..................................................
Instructions d’installation ....................................
Instructions d’installation du baril à bière.............
Utilisation ............................................................
Soins et entretien ...............................................
Dépannage .........................................................
Garantie ..............................................................
Contents / Table des matières / Índice
3,4
5
6,7
7-11
12,13
14
14
15
BARRIL REFRIGERADOR
Manual de uso y mantenimiento
Instrucciones de seguridad importantes ............
Caracteristicas ....................................................
Instrucciones de instalación .... .............................
Instrucciones para la instalación
del barril de cerveza ...........................................
Instrucciones de funcionamiento ........................
Limpieza y mantenimiento ..................................
Solucion sugeridad .............................................
Garantia ..............................................................
CAUTION:
PRÉCAUTION :
ADVERTENCIA:
Read and follow all safety rules and
operating instructions before first use of this
product.
Veuillez lire attentivement les consignes de
sécurité et les instructions d’utilisation avant
l’utilisation initiale de ce produit.
Lea y observe todas las reglas de seguridad
y las instrucciones de operación antes de
usar este producto por primera vez.
Ÿ
Ÿ
Model Modèle Modelo DKC052BSLDB-D
17,18
19
20,21
21-25
27
28
28
29
31,32
33
34,35
35-39
40,41
42
42
43
KEG COOLER
Owners Use and Care Guide
Safety Instructions ...............................................
Features ..............................................................
Installation Instructions ........................................
Beer Keg Installation Instructions .......................
Operating Instructions .........................................
Care and Maintenance ........................................
Troubleshooting ...................................................
Warranty ..............................................................
1
Includes American Sankey tap coupler only.
Inclut robinet de prise Américain Sankey
seulement.
Incluye grifo Sankey Americano solamente.
Welcome
Welcome to the Danby family. We’re proud of our quality products, and we believe in dependable service; like you will
find in this owner’s use and care guide, and like you will receive from our friendly customer service department. Best of
all, you will experience these values each and every time you use your Danby Keg Cooler. That’s important, because
your new appliance will be a part of your family for a long time.
For easy reference, may we suggest that you attach a copy of your sales receipt to this page, and note the information
below; you will need this information to obtain service under warranty.
Model No:
Serial No:
Date Purchased:
Before you call for service, there are a few things you can do to help us
serve you better.
Read this Owners Use and Care Guide:
It contains instructions to help you use and maintain your appliance
properly.
If you received a damaged appliance:
Immediately contact the builder (or dealer) that sold you the appliance.
Save time and money:
Check the Trouble shooting section before calling. This section helps you
solve common problems that may occur.
If you do need service, you can relax knowing help is only a phone call
away.
Need Help?
Tel: 1-800-26-
(1-800-263-2629)
2
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
GROUNDING
INSTRUCTIONS
FOR YOUR SAFETY: Pertaining to the risk of Fire, Electric Shock or Injury to Persons.
This appliance must be grounded. In the event of a malfunction or
breakdown, grounding will reduce the risk of electric shock by providing
a path of least resistance for electric current.
This appliance is equipped with a power cord having an equipment
grounding conductor and grounding plug. The plug must be plugged into
an appropriate wall outlet that is installed and grounded in accordance
with all existing local codes and ordinances.
Consult a qualified electrician or service person if the grounding
instructions are not clearly understood, or if doubt exist as to whether
your electrical wall outlets are properly grounded.
WARNING
If it becomes difficult to breathe and/or
your head starts to ache, abnormal con-
centrations of carbondioxide (CO2) may
be present in the area....
CLOSE THE MAIN VALVE ON THE
CO2 CYLINDER, VENTILATE AND
LEAVE THE ROOM IMMEDIATELY!
1. Always check the D.O.T.
(Department of Transport) as
well as the T.C. (Transport
Canada) testdate located on the
neckof the cylinder before
installation. If the date is older
than five (5) years,do not use,
return the gas cylinder to a gas
supplier for re-certification
(service charges may be
applicable).
2. Always connect a CO2 gas
cylinder to a regulator.Failure to
do so could result in an
explosion which can possibly
result in death or injury when the
cylinder valve is opened.
3. Never connect a CO2 gas
cylinder directly to beer keg.
4. Always secure a CO2 gas
cylinder in an "upright" position.
5. Always keep a CO2 gas cylinder
away from heat.
6. Never drop or throw a CO2 gas
cylinder.
7. Never connect a CO2 cylinder
unless there are two (2) safety
mechanism's in the pressure
system;
(a) One at or on the CO2 regulator.
(b) One at or on the product
container coupler in the
pressure gas line.
NOTE: The regulator andkeg
coupler supplied with
this unit are
inclusive of such safety
mechanisms.
8. CO2 gas cylinders should be
stored in the coolest part of the
establishment (preferably) at
70ºF (21ºC) and must always be
securely fastened in an "upright"
position.
9. Always ventilate area after any
leakage of CO2.
WARNING CO CAN BE
DANGEROUS!
2
CO2 Cylinders when charged contain
high pressure compressed gas which can
be hazardous if not handled properly.
Read and understand the following
procedures for CO2 cylinders before
installation;
3
Risk of fire or explosion due to puncturing of refrigerant tubing. Do not use sharp objects to aid in defrost.
Please handle with care. Keep flammable materials and vapors such as gasoline away from the refrigera-
tor. Use nonflammable cleaner.
Disposal of this unit should be in accordance with federal and local regulations.
WARNING! EXPLOSION HAZARD!
• This appliance must be connected to a properly grounded electrical
outlet (see Grounding Instructions)
Do not operate this appliance if it has a damaged power cord or plug.
• Do no use this product near water, for example: in a wet basement, near
a swimming pool or sink.
• Do not defrost this appliance using other electric appliances (i.e. hair
dryer) and never attempt to scrape or remove ice/frost from the
evaporator (cold plate) with sharp objects.
Always disconnect the appliance from the power supply before cleaning
and/or attempting repairs/servicing.
SAFETY
PRECAUTIONS
Repairs should be performed by qualified service personnel only.
IMPORTANT WARNING
• If you have purchased this appliance to replace an old one remove
either the gaskets, latches, lids or doors from the unused appliance. If it
was equipped with a door lock that cannot be opened from the inside,
(lock bolt) make sure the lock is removed, disabled or destroyed before
discarding, this will make it impossible for children to accidentally lock
themselves inside the appliance and suffocate.
• The refrigerator system of this appliance is filled with refrigerant and
insulating substances which should be treated and processed separately.
Call your nearest service agent or specialized servicing center. If you are
unable to locate one, contact your local authorities for proper disposal
instructions. Be careful not to damage any of the refrigeration lines of the
appliance.
DON’T WAIT DO THIS
NOW!
Improper disposal of worn out
appliances pose a risk of
entrapment to children.
Beer is easily available with Danby's new Keg Cooler, however, it is not
intended to be available to people under the legal age to consume beer. A
beer faucet lock kit for the purpose of limiting access, is readily available
and
can be purchased through our after sales service department (see
‘Optional Accessories’ ). Danby does not assume liability for the unlawful
use or consumption of the beer.
PLEASE DRINK RESPONSIBLY AND PLEASE DON'T
DRINK AND DRIVE!
IMPORTANT
WARNING
Important Safety Information
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
This unit is not designed for outside installation, including installation anywhere
that is not temperature controlled (garages, porches, carports, etc.).
4
Features
CHILL N’ TAP ACCESSORIES
INCLUDED
ACCESSORIES
Remove and inspect all accessories supplied with this unit are present
and in good condition. In the event any of the accessories are missing
and /or not in good condition, please call Danby TOLL FREE at the
number listed below and speak with one of our Customer Service
Representatives. (1-800-263-2629)
BEER TOWER
ASSEMBLY
BACK
1
3
2
4
5
6
7
8
9
10
11
12
13
1. Beer Tower
2. Rubber Gasket (may not be required in all unit configurations)
3. Safety Guard Rail
4. Drip Tray
5. Adjustable Thermostat
6. CO2 Regulator
7. CO2 Gas Cylinder
8. CO2 Gas Cylinder Support
9. Evaporator
10. Reversible Door
11. Beer Keg (not included)
12. Metal Plate
13. Castors (4)
5
D C
B
A
SPARE PARTS
(Can be replaced in case of leakage.)
A - Washer (19 x 4.2 x 2 mm)
B - Washer, black (21 x 13.5 x 5 mm)
C - Washer, black (37.5 x 25 x 8.3 mm)
D - Non-return valve
Installation Instructions
BEFORE USING YOUR
BEER DISPENSER
Remove the exterior and interior packing.
Check to be sure you have all of the following parts:
1 Safety Guard Rail
1 Drip Tray (2 Pieces)
1 CO2 Cylinder Support
1 CO2 Regulator
1 CO2 Empty Cylinder
1 CO2 Air Line Hose (Coloured)
1 Beer Keg Coupler
1 Beer Tower
1 Pull Handle (Beer Tower Faucet)
4 Plugs: For Guard Rail Holes
1 Metal Plate For Cabinet Bottom
2 Steel wire shelves
2 Steel Clamps for Coloured Hose (1 spare)
4 Castors (2 front with locks)
2 Metal Washers for front castors
1 Rubber Gasket (may not be required
in all unit configurations)
Before plugging in the keg cooler, let it stand upright for approximately 2
hours. This will reduce the possibility of a malfunction in the cooling
system from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
INSTALLATION OF
BEER DISPENSER
This appliance is designed to be free standing only, and should not be
recessed or built-in.
Place your Beer Dispenser on a floor that is strong enough to support
the Beer Dispenser when it is fully loaded.
Allow 3 inches of space between the back and sides of the Beer
Dispenser, which allows the proper air circulation to cool the compressor.
Locate the Beer Dispenser away from direct sunlight and sources of heat
(stove, heater, radiator, etc.). Direct sunlight may affect the acrylic
coating and heat sources may increase electrical consumption. Extreme
cold ambient temperatures may also cause the Beer Dispenser not to
perform properly. This unit is not designed for outside installation (ie
garages, porches, etc.)
Avoid locating the Beer Dispenser in excessive humidity.
Plug the Beer Dispenser into a dedicated, properly installed-grounded
wall outlet. Do not under any circumstances cut or remove the third
(ground) prong from the power cord. Any questions concerning power
and or grounding should be directed toward a certified electrician or an
authorized service center.
After plugging the appliance into a wall outlet, allow the unit to cool down
for 2-3 hours before placing any contents in the Beer Dispenser
compartment.
ELECTRICAL
CONNECTION
Improper use of the grounded plug can result in the risk of
electrical shock. If the power cord is damaged, have it replaced by
an authorized service center.
WARNING
This Beer Dispenser should be properly grounded for your safety. The
power cord of this Beer Dispenser is equipped with a three-prong plug
which mates with standard three prong wall outlets to minimize the
possibility of electrical shock.
Do not under any circumstances cut or remove the third ground prong
from the power cord supplied.
Use of extension cords is not recommended.
6
Installation Instructions
ELECTRICAL
CONNECTION (cont)
This Beer Dispenser requires a standard 115/120-volt, 60Hz electrical
outlet with three-prong ground receptacle. The cord should be secured
behind the Beer Dispenser and not left exposed or dangling to prevent
accidental injury.
Never unplug the Beer Dispenser by pulling the power cord. Always grip
the plug firmly and pull straight out from the receptacle.
CO2 GAS CAN BE DANGEROUS
CO2 cylinders contain high-pressure compressed gas which can
be hazardous if not handled properly. Make sure you READ and
UNDERSTAND the following procedures for CO2 cylinders
BEFORE INSTALLATION.
WARNING
1. ALWAYS connect the CO2 cylinder to a regulator. Failure to do so
could result in explosion with possible injury when the cylinder valve is
opened.
2. NEVER connect the CO2 cylinder directly to the keg.
3. ALWAYS follow correct procedures when cylinders are changed as per
local codes.
4. ALWAYS secure the CO2 cylinder in an upright position.
5. NEVER drop or throw a CO2 cylinder.
6. ALWAYS keep a CO2 cylinder away from heat. Store extra cylinders in
a cool place (preferably 70°F). Securely fasten with a chain in an
upright position when storing.
7. ALWAYS ventilate and leave the area immediately if CO2 leakage has
occurred.
8. ALWAYS check the D.O.T. test date on the cylinder neck before
installation. If over five (5) years, do not use, return cylinder to gas
supplier.
9. NEVER connect a keg without a safety pressure release.
a. One at or on the CO2 regulator
b. One at or on the product coupler
or in the pressure gas line.
Beer Keg Installation Instructions
CO2 TANK
COLOURED PRESSURE HOSE
KEG
AMERICAN
SANKEY TAP (COUPLER)
CLEAR HOSE
WITH WING NUT
TOWER
FAUCET ASSEMBLY
SINGLE GAUGE
PRESSURE
REGULATOR
TOWER
Keg Installation Sketch
Install the four castors (2 locking castors at front) into the unit’s bottom
(four screw holes pre-supplied) Figure (1) before installation. Figure (II)
is the final version. Put the metal washers provided on the front castors
before installing them.
METAL
WASHERS
Figure 1
Figure 2
7
CASTORS
Put metal washers
on the front castors.
Beer Keg Installation Instructions
CASTOR BRAKE GUIDE
STEP ON TO BRAKE
STEP ON TO RELEASE
BRAKE
INSTALLATION OF CO2
CYLINDER SUPPORT
• Install the metal support provided onto the 4 studs located on the exterior
back wall. Align the holes in the support with the studs and push down
firmly. (See Figure 1)
Figure 1 Figure 2 Figure 3
INSTALLATION OF CO2
CYLINDER
• The CO2 Cylinder does not come filled. The cylinder must be filled with
CO2 prior to use.
• Install your fully charged cylinder into the support stand.
INSTALLATION OF CO2
REGULATOR
Attach the CO2 regulator to the cylinder by turning the regulator nut onto
cylinder valve, making sure washer is securely inserted into connecting
nut. Tighten snug using an adjustable wrench (not supplied) and assure
there are no leaks - no hissing sounds. (See Figure 2)
INSTALLATION OF CO2
AIR LINE OUTSIDE
CABINET
• Remove plug located at the exterior back (top left hand corner).
• Save it for later use if you decide to convert unit to a refrigerator.
• Insert the open end of the air line into the cabinet through the uncovered
hole. (See Figure 4)
8
Beer Keg Installation Instructions
INSTALLATION OF CO2
AIR LINE HOSE TO
REGULATOR
Attach the open end of the hose to the hose barb connection on the
regulator.
Secure hose by using one clamp provided. Use pliers/screwdriver to
tighten clamp to prevent leaks. (See Figure 3)
INSTALLATION OF THE
BEER TOWER
Remove the top plug by twisting and pulling out, saving it for later use if
you decide to convert unit to an all refrigerator unit.
Unravel the beer line (clear hose) from the tower and insert the beer line
and wing nut through the uncovered hole on top.
Lock the beer tower assembly to the top and make sure to position the
beer faucet so it is aligned with the cabinet front (6 o’clock position).
The rubber gasket (# 2 in parts list), can be used to make the connection
between the tower and the cooler tighter if needed. If Beer Tower will not
turn to lock in place, try removing the rubber gasket. (Rubber gasket may
not be required in all unit configurations.)
INSTALLATION OF
PROTECTIVE METAL
PLATE
This plate should always be installed when the keg is in place to protect
against unnecessary damage to the floor of the cabinet.
INSTALLATION OF THE
BEER KEG
Position the beer keg directly in front of the open door. Using keg
handles only, carefully lift the beer keg. (See Figure 5)
To place the beer keg inside the cabinet, brace your knees behind the
beer keg. Lift the front of the keg just enough so the front edge of the
keg is resting on the front edge of the Beer Dispenser bottom cabinet.
(See Figure 6)
Grasp the keg handles and slide it all the way into the cabinet.
Figure 4
Figure 5 Figure 6
INSTALLATION OF THE
KEG COUPLER
Insert the keg coupler provided into the locking neck of the beer keg and
turn it clockwise to lock into position, making sure the keg coupler is in
the closed position. (See Figure 7)
9
INSTALLATION OF THE
CO2 AIR LINE HOSE
Attach the end of the air line (coloured) hose provided to the hose
connection on the keg coupler.
Beer Keg Installation Instructions
CONNECTING THE BEER
TOWER TO COUPLER
• Make sure the rubber washer is properly inserted into the coupler. See
Fig. 7 below.
• Make sure the small round bead is in place (dropped down into the top
of the coupler).
• Make sure the ball retainer is in place on the coupler, with the ‘arms’
down into the coupler.
• Place wing nut into the top of the coupler turning until tight.
HOW TO TAP A KEG OF
BEER
• Make sure that the CO2 is turned off, and the Secondary valve on the
regulator is in the ‘Closed’ position.
• Pull out and release the pressure release valve on the Coupler to purge
any air pressure.
Make sure the beer tower faucet is in the closed position.
• Pull tapping handle out and press downward until it locks into position.
(See Figure 8) The keg is now tapped.
OPENING THE CO2
CYLINDER MAIN VALVE
• Make sure the secondary shut-off valve (shown in figure 9 in ‘Open’
position) is closed. To open the main CO2 cylinder valve, slowly turn the
main valve counter-clockwise until fully open.
Notice the needle on the regulator gauge start to climb.
ADJUSTING THE CO2
REGULATOR
The gauge monitors low internal keg pressure and should be adjusted to
read between 10-12 psi. (See Figure 10). The pressure can be adjusted
as needed.
Release adjustment lock nut marked 2.
Using a flat screwdriver, turn regulator screw marked 3.
o To increase pressure, turn screw clockwise.
o To decrease pressure, turn screw counter - clockwise.
Retighten lock nut marked 2.
Open secondary shut off valve to let CO2 flow into the keg.
Allow several minutes for the keg to properly pressurize. Regulator
gauge may drop while this happens. (Note: Listen for hissing along all
connections to identify if there are any leaks)
Figure 7
Figure 8
Figure 9 Figure 10
10
Rubber washer goes here
IMPORTANT: Please put
rubber washer on the
coupler to avoid any leaks.
Beer Keg Installation Instructions
SPANNER FAUCET
WRENCH (Not Included)
Spanner faucet wrench (not provided) is for either removing or tightening
the connection.
Note: To prevent leakage, use a Spanner faucet wrench to further tighten
the faucet.
PLASTIC FAUCET
LEVER
Attach the black plastic lever (pull handle) to the top of the faucet by
tightening it by hand clockwise until the end, holding in the silver nut
underneath so it does not turn. If there is still a small drip from the faucet,
you may have tightened the plastic lever too much and may need to
unscrew silver snug counter-clockwise (as shown) one turn.
DISPENSING OF BEER
Keep beer keg refrigerated at all times.
Never allow beer lines to dry out.
Use clean beer glassware before pouring.
• Hold glass at a 45° angle when 2/3 full, start to straighten glass as the
glass fills.
Always make sure the faucet handle is pushed all the way back.
Note: Keg sizes that can be used in your beer dispenser
1/2 barrel 59 Liters 15.5 gals 1984 oz. 164/12-oz. Glass
1/4 barrel 30 Liters 7.8 gals. 992 oz. 82/12-oz. Glass
1/6 barrel 20 Liters 5.2 gals. 661 oz. 55/ 12-oz. Glass
1/8 barrel 15 Liters 4.0 gals. 496 oz. 41/ 12-oz. Glass
Note: Our Beer dispenser accepts domestic kegs up to 16-1/8” in
diameter, and up to 23-3/8” in height. Check with your distributor to make
sure keg is correct size.
11
Operating Instructions
SETTING THE
TEMPERATURE
The temperature is controlled by adjusting/setting the thermostat control
knob. To start the unit and achieve maximum cooling quickly;
• Turn the temperature control knob clockwise to the furthest (maximum)
setting on the blue (wide) section of the control dial. (Fig A)
Allow the unit to run at this setting for 3-4 hours.
• When maximum cooling is achieved, turn back the temperature control
knob to a moderate/medium temperature.
• To turn off (no cooling) rotate the control knob to the “0” (off)
position. (Fig.B.)
AUTOMATIC
DEFROSTING
There is no need to defrost the Beer Dispenser. Defrost water collects and
passes thru the drain outlet in the rear wall into a tray located above the
compressor, where it evaporates.
NOTE: If the unit is unplugged, power lost, or turned off; you must wait 3
to 5 minutes before restarting the unit. If you attempt to restart before this
time delay, the Beer Dispenser may not start.
CONVERTING TO AN
“ALL REFRIGERATOR”
1. Turn off the control knob to the “OFF” position.
2. Close the main valve on the CO2 cylinder.
3. Close the secondary shut-off valve on the regulator pipe.
4. Close the connection between the beer keg and the keg coupler.
5. Drain any remaining beer from the lines.
6. Disconnect the beer line and CO2 air line from the keg coupler
7. Remove the beer keg.
8. Remove the keg coupler.
9. Disconnect the air line from the CO2 cylinder.
10. Remove the CO2 air line from cabinet plug
11. Replace the air line rear cabinet plug
12. Remove the beer tower. Also pull the beer line thru the top of the
cabinet
13. Replace the top cabinet plug
14. Adjust temperature as desired.
Fig B.
Fig A.
12
Operating Instructions
CHANGING THE
REVERSIBLE DOOR
This Beer Dispenser has a door that can be set to open from the left or
right side. The unit is delivered to you with the door opening from the left
side. To reverse the opening direction, please follow the instructions
below.
To avoid personal injury to yourself and/or property, we
ecommend that someone assist you during the door reversal
process.
CAUTION
Undo the three screws in each
bracket using the Phillips
screwdriver.
Remove the screws and bracket.
Place to one side.
Slide the Larder Fridge door down
about 15cm (6’’) and off the top
hinge pin and lift away from the
freezer.
Using the flat bladed screw driver
remove the pin from the top bracket.
Replace it in the hinge bracket on
the opposite side.
Remove the screw from the side of
the Larder Fridge where the
bracket is to be re-fitted.
Slide the Larder Fridge door back
on to the top hinge, making sure it’s
the right way up. Screw the bottom
hinge into place on the new side.
Check that the door is aligned
horizontally and vertically and
that the seals are closed on all
sides before finally tightening
the bottom hinge. Re-adjust
the leveling feet.
1
2
3
4
5
6
7
13
Care and Maintenance
Troubleshooting
CLEANING YOUR BEER
DISPENSER
• Turn the temperature control to "OFF", unplug the Beer Dispenser, and
remove the contents.
• Wash the inside surfaces with a warm water and baking soda solution.
The solution should be about 2 tablespoons of baking soda to a quart of
water.
• Wash the shelves and stand with a mild detergent solution.
• Wipe down any electrical controls with a dry clothe.
• Wash the outside cabinet with warm water and mild liquid detergent.
Rinse well and wipe dry with a clean soft cloth.
VACATION TIME
• Short vacations: Leave the Beer Dispenser operating during vacations of
less than three weeks.
• Long vacations: If the appliance will not be used for several months,
remove all contents and unplug the power cord. Clean and dry the
interior thoroughly. To prevent odor and mold growth, leave the door
open slightly.
MOVING YOUR BEER
DISPENSER
• Remove all the contents.
• Securely tape down all loose items inside your Beer Dispenser.
• Tape the door shut.
• Be sure the Beer Dispenser stays secure in the upright position during
transportation. Also protect outside of Beer Dispenser with a blanket or
similar item.
You can solve many common Beer Dispenser problems easily, saving you the cost of a possible service call. Try the
suggestions below to see if you can solve the problem before calling the servicer.
Beer Dispenser does not operate
Turns on and off frequently
Vibrations
The Beer Dispenser seems to make too
much noise.
The door will not close properly.
PROBLEM
POSSIBLE CAUSE
Not plugged in.
The circuit breaker tripped or blown fuse.
The room temperature is hotter than normal.
The door is open too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The unit does not have proper clearance.
Check to assure that the Beer Dispenser is level.
The rattling noise may come from the flow of the refrigerant, which is
normal.
Gurgling, caused by liquid refrigerant cycling, is normal.
Contraction and expansion of the inside walls may cause popping and
crackling noises.
The Beer Dispenser is not level.
The Beer Dispenser is not level.
The door was reversed and not properly installed.
The gasket is dirty.
The shelves or stand are out of position.
The Keg is not properly centered in the unit.
The Castors are not attached.
14
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating
conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter
“Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
First Year
During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s
option, at no charge to the ORIGINAL purchaser.
To obtain
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance
Service
requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at
their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service
must be performed by a qualied service technician.
If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all
obligations of Danby under this warranty shall be void.
Boundaries of
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be
In Home Service
delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for
warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he
responsibility of the purchaser.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due
to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees
under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages
to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of
the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions
(extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).
Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our
AUTHORIZED SERVICE DEPOT.
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
04/09
1-800-263-2629
Warranty Service
In-home
If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest
service center your unit must be delivered to the nearest authorized Danby Service Depot, as service
must only be performed by a technician qualified and certified for warranty service by Danby. Transpor-
tation charges to and from the service location are not protected by this warranty and are the responsi-
bility of the purchaser.
During the first twelve (12) months, any functional parts of this product found to be defective, will be
repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.
Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized
Service Depot. Any appliance requiring service outside the limited boundaries of “In Home Service” ,it
will be the consumer’s responsibility to transport the appliance (at their own expense) to the original
retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.
Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby
service depot, where service must be performed by a qualified service technician. If service is performed
on the units by anyone other than an authorized service depot, or the unit is used for commercial
application, all obligations of Danby under this warranty shall be void.
First Year
To obtain
Service
Boundaries of
In Home Service
LIMITED IN-HOME APPLIANCE WARRANTY
This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is
used under the normal operating conditions intended by the manufacturer.
This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or
Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.
TERMS OF WARRANTY
Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.
Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other
contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or
implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or
guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation
or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons
or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit
and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for
damages to persons or property caused by the unit.
GENERAL PROVISIONS
No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:
1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating
conditions (extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for
outdoor application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event
warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.
Warranty Service
In-home
Danby Products Limited
PO Box 1778, Guelph, Ontario, Canada N1H 6Z9
Telephone: (519) 837-0920 FAX: (519) 837-0449
Danby Products Inc.
PO Box 669, Findlay, Ohio, U.S.A. 45840
Telephone: (419) 425-8627 FAX: (419) 425-8629
1-800-263-2629
07/13
Bienvenue
Bienvenue dans la famille Danby. Nous sommes fiers de nos produits de qualité et croyons au bien fondé de fournir une
assistance fiable à nos clients. Vous le découvrirez grâce à ce guide facile d’utilisation et vous pourrez l’entendre en
provenance des voix amicales de notre service d’assistance à la clientèle.
Mais, ce qui est encore mieux, vous pourrez bénéficier de ces valeurs à chaque utilisation de votre appareil. Ceci est
important parce que votre nouvel appareil fera partie de votre famille pour longtemps.
Numéro de modèle :
Numéro de série :
Date d’achat :
Voici quelques petites choses que vous pouvez effectuer avant de faire un
appel de service, pour nous aider à mieux vous servir:
Lisez ce guide :
Il comprend des instructions pour vous assister avec l’utilisation et
l’entretien adéquats de votre appareil.
Si votre appareil neuf est avarié :
Communiquez immédiatement avec le manufacturier (ou le revendeur).
Épargnez temps et argent :
Avant de faire un appel de service, résoudre le chapitre intitulé
“Dépannage”. Ce chapitre vous aidera à résoudre des problèmes communs
qui pourraient survenir. Si vous avez besoin de notre aide, vous pouvez
être assuré que
nous serons au bout du fil.
T
él: 1-800-26-
(1-800-263-2629)
Besoin d'aide?
16
Consignes de sécurité importantes
PRENDRE CONNAISSANCE DE TOUTES LES INFORMATIONS
RELATIVES À LA SÉCURITÉ AVANT D'UTILISER LE PRODUIT
CONSIGNES DE MISE À
LA TERRE
POUR VOTRE SÉCURITÉ: Au sujet des risques de brûlure, d’incendie, de choc électrique ou de blessure.
Cet appareil doit être mis à la terre. Dans le cas d’un mauvais
fonctionnement ou d’un bris, la mise à la terre réduit le risque de choc
électrique en permettant au courant électrique d’emprunter le chemin offrant
le moins de résistance.
Cet appareil est doté d’un cordon d’alimentation avec équipement
conducteur de mise à la terre et fiche bipolaire avec terre. La prise doit être
branchée dans une prise adéquate, installée et mise à la terre selon la
réglementation locale.
Consultez un électricien qualifié ou un technicien si les directives de mise à
la terre ne sont pas entièrement comprises, ou si un doute subsiste quant à
la mise à la terre appropriée des prises murales.
AVERTISSEMENT
S’il est difficile de respirer ou si un mal de
tête vous prend, il est possible que des
concentrations anormales de gaz
carbonique se trouvent dans la pièce…
FERMEZ LA VALVE PRINCIPALE DE LA
BOUTEILLE DE GAZ CARBONIQUE,
AÉREZ LA PIÈCE ET QUITTEZ-LA
IMMÉDIATEMENT!
1. Branchez toujours la bouteille de
gaz carbonique à un régulateur.
Sans quoi, l’ouverture de la valve
de la bouteille pourrait causer une
explosion qui risque d’entraîner la
mort ou des blessures.
2. Ne branchez jamais la bouteille de
gaz carbonique directement sur le
fût de bière.
3. Fixez toujours la bouteille de gaz
carbonique en position verticale.
4. Gardez toujours la bouteille de gaz
carbonique à l’abri de la chaleur.
5. Ne laissez jamais tomber et ne
lancez jamais une bouteille de gaz
carbonique.
6. Avant de l’installer, vérifiez toujours
la date d’essai du D.O.T. (Ministère
des transports), située sur le col
de la bouteille. Si l’essai a eu lieu il
y a plus de cinq (5) ans, retournez
la bouteille de gaz à votre
fournisseur.
7. Ne branchez jamais une bouteille
dont le mécanisme de pression ne
présente pas deux (2)
mécanismes de sécurité :
(a) un au niveau du régulateur de
gaz carbonique;
(b) un au niveau du coupleur de la
bouteille, sur
la conduite de
pression du gaz.
Le régulateur et le coupleur de fût
compris avec cet appareil constituent
de tels mécanismes de sécurité.
8. Les bouteilles de gaz carbonique
doivent être rangées
préférablement dans les pièces les
plus froides de l’établissement, à
70° F (21° C). Elles doivent
toujours être fixées en position
verticale.
9. Aérez toujours la pièce après une
fuite de gaz carbonique.
AVERTISSEMENT :
LE GAZ CARBONIQUE
PEUT ÊTRE
DANGEREUX!
Les bouteilles de gaz carbonique chargées
contiennent du gaz hautement pressurisé,
qui peut présenter un danger s’il n’est pas
manipulé correctement. Avant l’installation,
lisez et assurez-vous de bien comprendre
les procédures suivantes concernant les
bouteilles de gaz carbonique:
17
Risque d’incendie ou d’explosion causé par la perforation de tuyaux frigorigènes. Ne jamais utiliser un
objet pointu pour assister au dégel. Manipuler avec soin. Garder les matériaux et vapeurs inflammables
comme de l’essence loin du réfrigérateur. Utiliser un nettoyant ininflammable.
La mise au rebut de cet item doit être faite selon les lois locales et fédérales.
AVERTISSEMENT! DANGER D’EXPLOSION!
Consignes de sécurité importantes
• Cet appareil doit être branché à une prise électrique correctement mise à la
terre (voir Instructions de mise à la terre)
• N’utilisez pas cet appareil si son cordon ou sa fiche sont endommagés.
• N’utilisez pas ce produit près d’une source d’eau, tel un sous-sol humide,
une piscine ou un évier.
• Ne faites pas dégeler cet appareil à l’aide d’autres appareils électriques
(ex. : séchoir à cheveux) et ne grattez jamais la glace ou le givre de
l’évaporateur (plaque froide) à l’aide d’un objet coupant.
• Débranchez toujours l’appareil de la prise d’alimentation avant de le nettoyer
ou de tenter de le réparer.
CONSIGNES DE
SÉCURITÉ
Toute réparation doit être effectuée par le personnel qualifié
seulement.
AVERTISSEMENT
• Si vous avez acheté cet appareil afin d’en remplacer un vieux, retirez les
joints, verrous, couvercles ou les portes de l’appareil non utilisé. S’il était
équipé d’un verrou ne pouvant être ouvert de l’intérieur (boulon de blocage),
assurez-vous que le verrou est retiré, mis hors service ou détruit avant la
mise aux rebuts. Ceci empêchera les enfants de s’enfermer
accidentellement dans l’appareil et d’y étouffer.
• Le système de refroidissement de cet appareil est rempli de substances
réfrigérantes et isolantes devant être traitées séparément. Appelez votre
représentant de service ou un centre d’entretien spécialisé. Si vous êtes
incapable d’en trouver un, contactez votre autorité locale afin d’obtenir les
directives de mise aux rebuts appropriée. Prenez soin de ne pas
endommager les lignes de réfrigération de l’appareil.
N’ATTENDEZ PAS :
FAITES-LE
IMMÉDIATEMENT!
Une mauvaise mise aux rebuts
d’appareils usés constitue un risque
de piège pour les enfants.
La bière est facile d’accès avec la nouvelle glacière de bière pression de
Danby. La glacière n’est cependant pas conçue pour offrir de la bière
aux
personnes n’ayant pas l’âge légal pour consommer. Un jeu de verrouillage du
robinet permettant de restreindre l’accès à la bière est disponible et peut être
acheté auprès de notre service des ventes (voir Accessoires facultatifs).
Danby n’est pas responsable de la consommation ou utilisation illégales de la
bière.
RAPPELEZ-VOUS : LA MODÉRATION A BIEN MEILLEUR GOÛT! LE
VOLANT ET L’ALCOOL NE FONT PAS BON MÉNAGE!
AVIS IMPORTANT
18
Cet appareil n’a pas été conçu pour une installation extérieur, incluant l’installa-
tion dans un endroit qui n’a pas un température contrôlée (les garages, les
vérandas, les abris de voitures, etc.).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Danby DKC052BSLDB-D Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire