Danby DKC054A1BSLDB Manuel utilisateur

Marque: Danby

Modèle: DKC054A1BSLDB

Taper: Manuel utilisateur

Ce manuel convient également à

DKC054A1BSLDB

OWNER’S USE AND CARE GUIDE

GUIDE D’UTILISATION ET D'ENTRETIEN

GUÍA DE UTILIZACIÓN Y CUIDADO PARA EL PROPIETARIO

MODEL • MODÈLE • MODELO

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

2017.03.03

DKC054A1BSLDB

KEG COOLER

GLACIÈRE DE BIÈRE PRESSION

BARRIL REFRIGERADOR

1. Pressure gauge dial

2. Pressure relief ring

3. Open / Close valve

4. Tank strap

Ensure the CO

tank is

empty before courier

or 3

party transport.

DANGER - A full or

partially full CO

tank

is under extreme

pressure. Uncontrolled

release of pressure is

extremely dangerous. The

instructions below use the

regulator to control the

release of this pressure

in a safe manner. Do not

bypass the regulator.

1. Ensure tank is secure

2. Fully open valve

by turning counter-

clockwise. Pressure

gauge dial will show a

value if tank contains

pressure.

3. Gently pull pressure

relief ring. Released

gas should be heard.

4. The pressure dial

will read zero when

the tank is empty.

Continue to hold

pressure relief open

until tank is empty.

5. Release the pressure

relief ring.

6. Fully close valve by

turning clock-wise.

1. Cadran de manomètre

2. Anneau de limitation de pression

3. Soupape de l’ouverture /

fermeture

4. Sangle du réservoir

Vériﬁ ez que le réservoir de CO

est vide avant de messagerie ou

transport 3e parti.

DANGER - Un réservoir plein ou

partiellement plein de CO2 est

sous une pression extrême. La

libération incontrôlée de la pression

est extrêmement dangereuse. Les

instructions ci-dessous utilisent le

régulateur pour contrôler la libération

de cette pression de manière sûre. Ne

contournez pas le régulateur.

1. Assurez-vous que le réservoir est

bien ﬁ xé

2. Ouvrir complètement la soupape

en tournant dans le sens anti-

horaire. Le cadran du manomètre

indiquera une valeur si le réservoir

contient de la pression.

3. Tirez doucement la bague de

décharge de pression. Le gaz

rejeté doit être entendu.

4. Le cadran de pression indique

zéro lorsque le réservoir est

vide. Continuez à maintenir le

soulagement de pression ouvert

jusqu’à ce que le réservoir soit

vide.

5. Relâcher l’anneau de décharge de

pression.

6. Fermez complètement la soupape

en tournant dans le sens horaire.

1. Indicador del manómetro

2. Anillo de alivio de presión

3. Abrir / cerrar la válvula

4. Correa del tanque

Asegúrese de que el tanque

de CO

esté vacío antes del

transporte por mensajería o por

terceros.

PELIGRO - Un tanque lleno o

parcialmente lleno de CO

está

bajo presión extrema. La liberación

incontrolada de presión es

extremadamente peligrosa. Las

instrucciones a continuación utilizan el

regulador para controlar la liberación de

esta presión de una manera segura. No

elimine el regulador.

1. Asegúrese de que el tanque esté

seguro

2. Abra completamente la válvula

girando en sentido antihorario. El

indicador del manómetro mostrará

un valor si el tanque contiene

presión.

3. Tire suavemente el anillo de alivio

de presión. Se debe oir el gas

liberado.

4. El dial de presión mostrará cero

cuando el depósito esté vacío.

Continúe manteniendo el alivio de

presión abierto hasta que el tanque

esté vacío.

5. Suelte el anillo de alivio de presión.

6. Cierre completamente la válvula

girándola en el sentido de las

agujas del reloj.

KEG COOLER

Owner’s Use and Care Guide ...........................................1-16

• Welcome

• Important Safety Information

• Features

• Installation Instructions

• Operation Instructions

• Care and Maintenance

• Troubleshooting

• Warranty

GLACIÈRE DE BIÈRE PRESSION

Guide d’utilisation et d’entretien du propriétaire..........17-32

• Bienvenue

• Consignes de sécurité importantes

• Caractéristiques

• Consignes d’installation

• Consignes d’utilisation

• Soins et entretien

• Dépannage

• Garantie

BARRIL REFRIGERADOR

Guía de utilización y cuidado para el propietario........33-48

• Bienvenido

• Información importante sobre seguridad

• Características

• Instrucciones de instalación

• Instrucciones de funcionamiento

• Cuidado y mantenimiento

• Solución sugerida

• Garantía

Model • Modèle • Modelo

DKC054A1BSLDB

Includes American Sankey tap coupler only.

Inclut robinet de prise Américain Sankey seulement.

Incluye grifo Americano solamente.

TO OBTAIN WARRANTY SERVICE YOU MUST PROVIDE A VALID PROOF OF PURCHASE.

PLEASE STAPLE YOUR RECEIPT TO THIS PAGE FOR FUTURE REFERENCE.

POUR OBTENIR LE SERVICE SUR GARANTIE VOUS DEVEZ FOURNIR UNE PREUVE D’ACHAT

VALIDE. VEUILLEZ AGRAFER VOTRE REÇU À CETTE PAGE POUR RÉFÉRENCE FUTURE.

PARA OBTENER SERVICIO DE GARANTÍA, DEBE PROVEER UN RECIBO ORIGINAL. POR

FAVOR ENGRAPE SU RECIBO A ÉSTA PÁGINA EN CASO QUE NECESITE HACER UN

RECLAMO.

CONTENTS

TABLE DES MATIÈRES

ÍNDICE

Welcome

Welcome to the Danby family. We are proud of our quality products, and we believe in dependable service. We suggest

that you read this Owner’s Manual before plugging in your new appliance as it contains important operational information,

safety information, troubleshooting and maintenance tips to ensure the reliability and longevity of your appliance.

Visit www.Danby.com to access self-service tools, FAQs and much more. For additional assistance call 1-800-263-2629.

Note the information below; you will need this information to obtain service under warranty.

To receive service, you must provide the original receipt.

Model Number:

Serial Number:

Date of Purchase:

NEED HELP?

Before you call for service, here are a few things you can do to help

us serve you better:

Read this Owner’s Use and Care Guide:

It contains instructions to help you use and maintain your

appliance properly.

If you received a damaged appliance:

Immediately contact the retailer (or builder) that sold you the

appliance.

Save time and money:

Check the Troubleshooting section at the end of the guide before call-

ing. This section helps you solve common problems that may occur.

If you do need service, you can relax, knowing help is only a phone

call away.

1-800-26-

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

OPERATION REQUIREMENTS

To avoid installation or operation difﬁ culties, read these instructions thoroughly.

• This appliance must be grounded. Connect only to a properly grounded outlet. See Grounding

Instructions section.

• Do not operate this appliance if it has a damaged power cord or plug, if it is not working properly,

or if the appliance has been damaged or dropped. If the power cord is damaged it must be

replaced by the manufacturer, its service agent or similarly qualiﬁ ed person to avoid hazard.

• Never allow children to operate, play with, or crawl inside the appliance.

• Never clean appliance parts with ﬂ ammable ﬂ uids. The fumes can create a ﬁ re hazard or

explosion.

• Do not store or use gasoline or any other ﬂ ammable vapors or liquids in the vicinity of this or any

other appliance. The fumes can create a ﬁ re hazard or explosion.

• Do not splice the power cord that is equipped with this appliance.

• Keep power cord away from heated surfaces.

• Do not immerse power cord, plug or the appliance itself in water.

• Do not use this product near water for example, in a wet basement, laundry room or near a sink.

• Do not use corrosive chemicals or vapors in this appliance.

• Use this appliance only for its intended use, as described in this manual.

• Do not store open containers in this appliance.

• Do not cover or block any openings on the appliance.

• Do not store perishable food items such as (but not limited to) meats and dairy products in your

wine cooler. This appliance does not get cold enough to be food safe.

• This appliance is intended for household use only. Do not operate or store this appliance

outdoors.

• This appliance should be serviced only by qualiﬁ ed service personnel. Contact the nearest

authorized service facility for examination, repair or adjustment.

• Before connecting the appliance to a power source, let it stand upright for approximately 6

hours; this will reduce the possibility of a malfunction in the cooling system from handling during

transportation.

DANGER: Risk of child entrapment. Before you throw away your old appliance:

• Take off doors or remove the gasket.

• Leave the shelves in place so that children may not easily climb in.

DON’T WAIT! DO IT NOW!

IMPORTANT WARNING

SAVE THESE INSTRUCTIONS!

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the

risk of electric shock by providing an escape wire for the electric current. This appliance is equipped

with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet

that is properly installed and grounded

WARNING - Improper use of the grounding plug can result in a risk of electric shock. Consult a

qualiﬁ ed electrician or service agent if the grounding instructions are not completely understood, or if

doubt exists as to whether the appliance is properly grounded.

If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

For best operation, plug this appliance into its own electrical outlet to prevent ﬂ ickering of lights,

blowing of fuse or tripping of circuit breaker

DO NOT USE AN EXTENSION CORD

Use an exclusive 115V wall outlet. Do not connect your appliance to extension cords or together with

another appliance in the same wall outlet. Do not splice the cord. Do not under any circumstances

cut or remove the third ground prong from the power cord. Do not use an adapter plug with this

appliance.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAFETY REQUIREMENTS

Ensure that component parts shall be replaced with like components and that servicing shall be done

by factory authorized service personnel, so as to minimize the risk of possible ignition due to incorrect

parts or improper service.

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the

risk of electrical shock by providing an escape wire for the electrical current. The serial rating plate

indicates the voltage and frequency the appliance is designed for.

WARNING! EXPLOSION HAZARD! Risk of ﬁ re or explosion due to puncturing of refrigerant tubing.

Do not use sharp objects to aid in defrost. Please handle with care. Keep ﬂ ammable materials and

vapors such as gasoline away from the refrigerator. Use nonﬂ ammable cleaner.

Disposal of this unit should be in accordance with federal and local regulations.

This appliance is not intended for use by persons (including children) whose physical, sensory or

mental capabilities may be different or reduced, or who lack experience or knowledge, unless such

persons receive supervision or training to operate the appliance by a person responsible for their

safety.

WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of

obstruction.

WARNING: Do not use mechanical devices or other means to accelerate the defrosting process,

other than those recommended by the manufacturer.

WARNING: Do not damage the refrigerant circuit.

WARNING: Do not use electrical appliances inside the food storage compartments of the appliance,

unless they are of the type recommended by the manufacturer.

IMPORTANT WARNING

Beer is easily available with Danby’s Keg Cooler, however, it is not intended to be available to

people under the legal age to consume beer. Danby does not assume liability for the unlawful

use or consumption of the beer.

PLEASE DRINK RESPONSIBLY AND PLEASE DON’T DRINK AND DRIVE!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

WARNING: CO

CAN BE DANGEROUS!

Cylinders, when charged, contain high pressure compressed gas which can be hazardous if not

handled properly. Read and understand the following procedures for CO

cylinders before installation:

1. Always check the D.O.T. (Department of Transportation) as well as the T.C. (Transport Canada)

test date located on the neck of the cylinder before installation. If the date is older than ﬁ ve (5)

years, do not use! Return the gas cylinder to a gas supplier for re-certiﬁ cation (service charges

may be applicable).

2. Always connect a CO

gas cylinder to a regulator. Failure to do so could result in an explosion

which can possibly result in death or injury when the cylinder valve is opened.

3. Always follow correct procedures when cylinders are changed as per local codes.

4. Always secure a CO

gas cylinder in an “upright” position.

5. Always keep a CO

gas cylinder away from heat. Store extra cylinders in a cool place (preferably

70°F/21°C). Securely fasten with a chain in an upright position when storing.

6. Always ventilate and leave the area immediately after any leakage of CO

7. Never connect a CO

gas cylinder directly to a beer keg.

8. Never drop or throw a CO

cylinder.

9. Never connect a keg without at least one safety pressure release. There are two safety

mechanisms in the pressure system;

• One at or on the CO

regulator.

• One at or on the product container coupler in the pressure gas line.

Note: The regulator and keg coupler supplied with this unit are inclusive of such safety

mechanisms.

WARNING

If it becomes difﬁ cult to breathe and/or your head starts to ache, abnormal concentrations of

carbon dioxide (CO

) may be present in the area.

CLOSE THE MAIN VALVE ON THE CO

CYLINDER, VENTILATE AND LEAVE THE ROOM

IMMEDIATELY!

BEFORE USING YOUR KEG COOLER

• Remove the exterior and interior packaging.

• Check to be sure you have all the following parts:

• 2 Safety Guard Rail

• 1 drip tray (2 pieces)

• 1 CO

Cylinder support

• 1 CO

Regulator

• 1 CO

Empty Cylinder

• 1 CO

Gas line hose (coloured)

• 1 Beer Hose

• 1 Beer keg couplers

• 1 Beer tower

• 1 Pull handle (Beer tower faucet)

• 4 Plugs: For guard rail holes

• 1 metal plate for cabinet bottom

• 3 Wire shelf

• 1 steel clamp for coloured hose

• 2 plastic washers for front casters

• 4 Casters (2 front with locks)

• Before plugging in the keg cooler, let it stand upright for approximately 6 hours. This will reduce

the possibility of a malfunction in the cooling system from handling during transportation.

• Clean the interior surface with lukewarm water using a soft cloth.

INCLUDED ACCESSORIES

Remove and inspect all accessories supplied with this unit and ensure they are all present and in

good condition. In the event any of the accessories are missing and/or not in good condition, please

call Danby toll free at 1-800-263-2629 and speak with one of our Consumer Service Representatives.

1. Beer Tower

2. Rubber Gasket (may not be

required in all unit conﬁ gurations)

3. Safety Guard Rail

4. Drip Tray

5. Adjustable Thermostat

6. CO

Regulator

7. CO

Gas Cylinder

8. CO

Gas Cylinder Support

9. Evaporator

10. Door

11. Beer Keg (not included)

12. Metal Plate

13. Castors (4)

Installation Instructions

INSTALLATION OF KEG COOLER

• This appliance is designed to be free standing only and should not be recessed or built-in.

• Place your keg cooler on a ﬂ oor that is strong enough to support the unit when it is fully loaded.

• Allow 8-12 cm (3-5 inches) of space between the back and sides of the keg cooler and any

adjacent wall to allow proper air circulation to cool the compressor.

• Locate the keg cooler away from direct sunlight and sources of heat (stove, heater, radiator,

etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical

consumption. Extreme cold ambient temperatures may also cause the keg cooler not to perform

properly.

• This unit is not designed for outside installation (i.e. garages, porches, patios etc.).

• Avoid locating the keg cooler in excessive humidity.

• Plug the keg cooler into a dedicated, properly installed-grounded wall outlet. Do not under any

circumstance cut or remove the third ground prong from the power cord. Any questions concerning

power and or grounding should be directed toward a certiﬁ ed electrician or an authorized service

centre.

• After plugging the appliance into a wall outlet, allow the unit to cool down for 2-3 hours before

placing any contents in the keg cooler compartment.

BEER KEG INSTALLATION INSTRUCTIONS

Keg Installation Sketch

Pressure

Regulator

Faucet Assembly

Tower

Clear Hose with Wing Nut

American Sankey

Tap (Coupler)

Keg

Coloured Pressure Hose

Tank

Installation Instructions

WARNING

GAS CAN BE DANGEROUS

cylinders contain high-pressure compressed gas which can be

hazardous if not handled properly. Make sure you read and understand all

safety procedures for CO

cylinders before installation.

METAL

WASHERS

Fig. 1

Fig. 2

BEER KEG INSTALLATION INSTRUCTIONS

Install the four castors. The two locking castors should be placed at the front. Four screw holes have

been pre-drilled into the unit’s bottom at each corner for each castor. Put the plastic washers provided

on the front castors before installing them.

Castors

Put washers on the

front casters.

Castor Brake Guide

Installation Instructions

The two front castors are supplied with brakes to ensure the unit does not move excessively while

being used. It is recommended to engage the brakes while the unit is in use to avoid damage to the

unit, the contents or your personal property.

Installation of CO

Cylinder Support

Install the metal support provided onto the four studs

located on the exterior back wall of the chassis.

Align the holes in the support with the studs and push

down ﬁ rmly.

Step on to

brake

Step on to

release brake

Installation of the Beer Tower

• Remove the plug from the top of the fridge cabinet

by twisting and pulling out. Save the plug for

later use if you decide to convert the unit to a

refrigerator.

• Unravel the beer line (clear hose) from the tower

and insert the beer line and wing nut through the

uncovered hole on top of the unit.

• Lock the beer tower assembly to the top of the unit

and make sure to position the beer faucet so it is

aligned with the front of the cabinet.

• The rubber gasket can be used to make the

connection between the tower and the cooler

tighter if needed. If the beer tower will not turn

to lock in place, try removing the rubber gasket.

(The rubber gasket may not be required in all unit

conﬁ gurations).

• If the tower faucet is leaking or if the beer is very

foamy, ensure that the washers inside the faucet

are intact. Replace the washers with spare parts

from the accessory bag, if necessary.

Installation of CO

Cylinder and CO

Regulator

Installation Instructions

The CO

cylinder does not come ﬁ lled. The cylinder

must be ﬁ lled with CO

before use.

Place the charged cylinder into the support stand.

Attach the CO

regulator to the cylinder by turning

the regulator nut onto the cylinder valve, making sure

the washer is securely inserted into the connecting

nut. Tighten snug using an adjustable wrench (not

supplied) and ensure there are no leaks, i.e. no hissing

sounds when the CO

is turned on.

Installation of CO

Air Line Outside Cabinet and CO

Air Line Hose to Regulator

Remove the plug located at the exterior back of the

cabinet, in the top left hand corner. Save the plug

for later use if you decide to convert the unit to a

refrigerator.

Feed the gas line through the cabinet and out through

the uncovered hole.

Attach the open end of the hose to the hose barb

connection on the regulator. Secure the hose by using

one clamp provided. Use pliers or a screwdriver to

tighten the clamp to prevent leaks.

1. Tap rocker washer

2. Tap valve washer

3. Tap valve spool washer

Installation of the Beer Keg

• Position the beer keg directly in front of the open door. Using keg

handles only, carefully lift the beer keg.

• To place the beer keg inside the cabinet, brace your knees behind

the beer keg. Lift the front of the keg just enough so the front end

of the keg is resting on the front edge of the keg cooler bottom

cabinet.

• Grasp the keg handles and slide it all the way into the cabinet.

Note: Two people should lift the keg to avoid back injury.

Installation of the CO

Air Line Hose

Attach the end of the air line (coloured) hose provided to the hose connection on the side of the

coupler. Ensure that the check valve is inserted into the connection, number 4 on the image below.

If, after assembly, beer will not ﬂ ow, ensure that the check valve has a small hole in it. If there is no

hole in the check valve then CO

cannot enter the line and the beer will not ﬂ ow.

Installation of the Protective Metal Plate

The protective metal plate should be installed on the bottom of the inside of the cabinet. This plate

should always be installed when a keg is in place to protect the ﬂ oor of the cabinet against damage.

Installation Instructions

1. Valve washer

2. Valve spool plastic rod

3. Valve spool O-type washer

4. Check valve

5. Valve washer

6. Valve washer

Connecting the Beer Tower to the Coupler

• Ensure all washers are properly inserted into the

coupler, as per below image.

• Ensure the valve spool plastic rod is in place inside the

coupler, number 2 on the below image.

• Place the wing nut attached to the end of the beer line

into the top of the coupler, turning until tight.

If, after assembly, the beer is very foamy, it most likely

means that a connection in the coupler is leaking and air

is entering the lines. Double check all connections in the

coupler and replace the washers from the accessory bag

as necessary.

Installation of the Keg Coupler

Insert the keg coupler into the locking neck of the beer keg and turn it clockwise to lock into position,

making sure the keg coupler handle is in the closed position, with the handle up.

How to Tap a Keg of Beer

• Make sure the CO

is turned off and the valve on the regulator is in the closed position.

• Pull out and release the pressure release valve on the coupler to purge any air pressure.

• Make sure the beer tower faucet handle is in the closed position.

• Pull coupler handle out and downward until it locks into its open position. The teeth on the

underside of the coupler will bite into the locking neck of the beer keg.

Note: If a keg is very tall, it may be necessary to connect the coupler to the keg before inserting the

keg into the keg cooler.

Opening the CO

Cylinder Main Valve

• Make sure the secondary shut-off valve (shown below in “open” position) is closed. To open the

main CO

cylinder valve, slowly turn the main valve counter-clockwise until fully open.

• Notice the needle on the regulator gauge start to climb.

Adjusting the CO

Regulator

The gauge monitors low internal keg pressure and should be adjusted to

read between 8-12 PSI. The pressure can be adjusted as needed. If the

beer is very foamy, try turning the PSI down. If the ﬂ ow of beer is very

weak, try turning the PSI up.

Note: After making any adjustment to the PSI, wait 5 - 10 minutes

before attempting to pour another beer to allow the pressure to equalize.

• Release adjustment lock nut marked 2.

• Using a ﬂ at screwdriver, turn regulator screw marked 3.

- To increase pressure, turn screw clockwise.

- To decrease pressure, turn screw counter-clockwise.

• Retighten lock nut marked 2.

• Open secondary shut off valve to let CO

ﬂ ow into the keg.

• Allow several minutes for the keg to properly pressurize. Regulator

gauge may drop while this happens.

Note: Listen for hissing along all connections to identify if there are any

leaks.

Installation Instructions

Coupler closed position Coupler open position

Coupler pressure

release valve

Secondary shut

off valve

Main shut

off valve

Plastic Faucet Lever

Attach the black plastic lever (pull handle) to the top of the faucet by

tightening it by hand going clockwise until the end, holding in the silver nut

underneath so it does not turn. If there is still a small drip from the faucet,

you may have overtightend the silver nut and may need to unscrew silver

snug going counter-clockwise (as shown one turn).

DISPENSING OF BEER

• Keep beer keg refrigerated at all times.

• Never allow beer lines to dry out.

• Use clean glassware before pouring.

• Hold glass at a 45° angle, when it is 2/3 full, start to straighten glass as the glass ﬁ lls.

• Always make sure the faucet handle is pushed all the way back.

Note: The refrigerator compartment cannot accommodate the “Coors” style beveled barrel keg.

Note: Our keg cooler accepts domestic kegs up to 16-1/8” in diameter and up to 23-3/8” in height.

Check with your distributor to make sure keg is correct size.

Note: It is important to allow the keg to sit upright and undisturbed, for 2 hours before tapping.

Spanner Faucet Wrench

Spanner faucet wrench (provided) is for either removing or tightening the

faucet connection.

Note: To prevent leakage, use the provided wrench to further tighten the

faucet connection.

Installation Instructions

Keg sizes that can be used in your keg cooler

1/2 barrel 59 Liters 15.5 gals 1984 oz. 164 x 12-oz. Glasses

1/4 barrel 30 Liters 7.8 gals. 992 oz. 82 x 12-oz. Glasses

1/6 barrel 20 Liters 5.2 gals. 661 oz. 55 x 12-oz. Glasses

1/8 barrel 15 Liters 4.0 gals. 496 oz. 41 x 12-oz. Glasses

SETTING THE TEMPERATURE

The temperature is controlled by adjusting the thermostat control knob. To start the unit and achieve

maximum cooling quickly:

• Turn the temperature control knob clockwise to the maximum setting on the wide, blue section of

the control dial (Fig. A).

• Allow the unit to run at this setting for 3-4 hours.

• When maximum cooling is achieved, turn back the temperature control knob to a medium

temperature.

• To turn off the cooling, rotate the control knob to the “0” (OFF) position (Fig. B).

Fig A.

Max Max

MinMin

AUTOMATIC DEFROSTING

There is no need to defrost the keg cooler. Defrost water collects and passes through the drain outlet

in the rear wall into a tray located above the compressor, where it evaporates.

Note: If the unit is unplugged, power lost or turned off, you must wait 3 to 5 minutes before restarting

the unit. If you attempt to restart before this time delay, the compressor may not start.

CONVERTING TO AN ALL REFRIGERATOR

1. Turn the control knob to the “OFF” position.

2. Close the main valve on the CO

cylinder.

3. Close the secondary shut-off valve on the regulator pipe.

4. Close the connection between the beer keg and the keg coupler.

5. Drain any remaining beer from the lines. (We recommend cleaning at this point, please see Care

and Maintenance section).

6. Disconnect the beer line and CO

gas line from the keg coupler.

7. Remove the beer keg.

8. Remove the keg coupler.

9. Disconnect the gas line from the CO

cylinder.

10. Remove the CO

gas line from cabinet plug.

11. Replace the gas line rear cabinet plug.

12. Remove the beer tower. Also pull the beer line through the top of the cabinet.

13. Replace the top cabinet plug.

14. Adjust the temperature as desired.

Note: In order to convert the unit, you must disconnect the gas line from the regulator in order to

remove it from the cabinet.

Note: If you desire a shelf in the converted “All Refrigerator” install the shelf by sliding it into the

desired spot in the unit.

Fig. BFig. A

Operating Instructions

DOOR REVERSAL INSTRUCTIONS

To avoid personal injury to yourself or property, we recommend that someone assist you during the

door reversal process.

This keg cooler has a door that can be set to open from the left or right side. This unit is delivered

to you with the door opening from the left side. To reverse the opening direction, please follow the

instructions below.

1. Undo the three (3) screws in each bracket using a Phillips screwdriver.

2. Remove the screws and bracket. Place to one side.

3. Slide the door down about 15 cm (6”) and off the top hinge pin and lift away.

4. Use a ﬂ at head screwdriver to remove te pin from the top bracket. Replace it in the hinge bracket

on the opposite side.

5. Remove the screw from the side of the fridge where the bracket is to be re-ﬁ tted.

6. Slide the fridge door back onto the top hinge, making sure it’s the right way up. Screw the bottom

hinge into place on the new side.

7. Check that the door is aligned horizontally and vertically and that the seals are closed on all sides

before ﬁ nally tightening the bottom hinge.

Operating Instructions

CLEANING YOUR KEG COOLER

• Turn the temperature control to “OFF”, unplug the keg cooler, and remove the contents.

• Wash the inside surfaces with a warm water and baking soda solution. The solution should be 2

tablespoons of baking soda to a quart of water.

• Wash the shelves and stand with a mild detergent solution.

• Wipe down any electrical controls with a dry cloth.

• Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with

a clean soft cloth.

CLEANING YOUR BEER LINES

Beer lines have to periodically be cleaned because of a crystallized sugar build up which forms on

the ﬁ ttings, lines and taps commonly referred to as “beerstore”. If the “beerstore” is not completely

removed in a cleaning process it will leave an unsanitary surface that can harbor microorganisms

which will cause an undesirable ﬂ avour and/or cause the beer to go ﬂ at. Sufﬁ cient “beerstore” will

also lead to dispense problems ranging from ‘wild’ beer (too much foam) to ﬂ at beer, regardless of the

carbonation levels or quality (age) of the beer in the keg.

Scheduled line and faucet cleaning, with the proper equipment and chemical, eliminates the build-up

of “beerstore” protecting the integrity of the product and condition of the dispense system and seals.

The dispenser (beer) line should be cleaned approximately once every three (3) weeks or every other

keg - which ever comes ﬁ rst. The dispenser faucet should be cleaned on a weekly basis or prior to

every use if not used on a regular basis.

Note: If you have trouble manipulating the faucet lever, this is usually indicative that it may require

cleaning. DO NOT apply force to move the handle in this situation, as this will likely lead to damaging

the handle or faucet, and will not be covered by your warranty.

A standard cleaning kit will perform approximately eight (8) scheduled line cleanings. Line cleaning

kits are readily available and can be purchased through our after sales service department.

For more information please call 1-800-26-DANBY (1-800-263-2629).

VACATION

Short Vacations - Leave the keg cooler operating during vacations of less than three (3) weeks.

Long Vacations - If the appliance will not be used for several months, remove all contents and

unplug the power cord. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave

the door open slightly.

MOVING YOUR KEG COOLER

• Remove all the contents.

• Securely tape down all loose items inside your keg cooler.

• Tape the door shut.

• Be sure the keg cooler stays secure in the upright position during transportation. Also protect the

outside of the keg cooler with a blanket or similar item.

Care and Maintenance

PROBLEM POSSIBLE CAUSE

The unit does not operate • Not plugged in

• The circuit breaker tripped or blown fuse

Turns on and off

frequently

• The room temperature is hotter than normal

• The door is open too often

• The door is not closed completely

• The temperature control is not set correctly

• The door gasket does not seal properly

• The unit does not have proper clearance

Vibrations • Check that the keg cooler is level

The keg cooler seems to

make too much noise

• The rattling noise may come from the ﬂ ow of refrigerant, which is

normal

• Gurgling, caused by liquid refrigerant cycling is normal

• Contraction and expansion of the inside walls may cause popping

and crackling noises

• The keg cooler is not level

The door will not close

properly

• The keg cooler is not level

• The door was reversed and not properly reinstalled

• The gasket is dirty

• The shelves or stand are out of position

• The keg is not properly centered in the unit

• The casters are not attached

Excessive beer foam • Ensure the beer line hose from the tower and the CO

air line hose

from the CO

regulator are attached to the correct connections on

the coupler; beer line to the top of the coupler, CO

air line to the

side of the coupler

• Check that there are no leaks in any connections

• Ensure that the reed valve in the CO

connection at the coupler

has a hole in it

• The CO

pressure may be set too high; try turning the pressure

down

• Ensure that the valve spool plastic rod is inserted into the coupler

Weak beer ﬂ ow • Ensure the beer line hose from the tower and the CO

air line hose

from the CO

regulator are attached to the correct connections on

the coupler; beer line to the top of the coupler, CO

air line to the

side of the coupler

• Check that there are no leaks in any connections

• Ensure that the reed valve in the CO

connection at the coupler

has a hole in it

• The CO

pressure may be set too low; try turning the pressure up

• Ensure there are no bends or kinks in any of the hoses that could

impede ﬂ ow

Troubleshooting

Danby Consumer Care: 1-800-263-2629

Hours of operation:

Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time

Friday 8:30 am - 4:00 pm Eastern Standard Time

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

If the appliance is installed in a location that is 100 kilometres (62 miles) or more from the nearest

service centre your unit must be delivered to the nearest authorized Danby Service Depot, as service

must only be performed by a technician qualified and certified for warranty service by Danby. Transpor-

tation charges to and from the service location are not protected by this warranty and are the responsi-

bility of the purchaser.

During the first twelve (12) months, any functional parts of this product found to be defective, will be

repaired or replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized

Service Depot. Any appliance requiring service outside the limited boundaries of “In Home Service” ,it

will be the consumer’s responsibility to transport the appliance (at their own expense) to the original

retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby

service depot, where service must be performed by a qualified service technician. If service is performed

on the units by anyone other than an authorized service depot, or the unit is used for commercial

application, all obligations of Danby under this warranty shall be void.

First year

To obtain

service

Boundaries of

in-home service

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is

used under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or

Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or

implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or

guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation

or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons

or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit

and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for

damages to persons or property caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (extremely high or low room temperature).

5) Use for commercial or industrial purposes (i.e., If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.

7) Service calls resulting in customer education.

8) Improper Installation (i.e., building-in of a free standing appliance or using an appliance outdoors that is not approved for

outdoor application). Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event

warranty service is required, present this document to our AUTHORIZED SERVICE DEPOT.

Warranty Service

In-home

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

07/14

Merci d’avoir choisi Danby

Nous savons que vous êtes excité. Nous sommes aussi! Cependant, le plus que vous vous familiarisez avec votre

nouvel appareil, le mieux va être votre expérience. Nous suggérons donc de lire ces instructions avant connecter votre

nouvel appareil. Ce manuel contient des informations opérationnel important qui vous aidera à faire un usage pleine de les

caractéristiques techniques disponibles dans votre appareil Danby. Le manuel contient également des informations conçu

pour améliorer la fiabilité et la sécurité de votre appareil ainsi que des conseils pour le maintien, pour vous assurez des annees

de bonheur.

Se il vous plaît visitez www.danby.com pour accéder les outils libre-service, FAQ et plus encore. Si jamais vous avez besoin

d'aide supplémentaire, s’il vous plaît appelez 1-800-26-Danby (1-800-263-2629). S’il vous plaît ayez votre facture d’achat, le

numéro de modèle, et le numéro de série près durant l'appel.

Remarque : Ces renseignements seront nécessaires si votre appareil a besoin d’entretien ou pour les demandes de

renseignements généraux. Pour bénéficier d’une opération de maintenance ou de dépannage, le reçu

original sera exigé.

Numéro de modèle :

Numéro de serie :

Date d’achat :

BESOIN D’ASSISTANCE ?

Veuillez trouver quelques conseils avant de faire appel à nos services, cela

nous aidera à mieux vous servir :

Lisez ce guide :

Il comprend des instructions pour l’utilisation et l’entretien adapté de votre

appareil.

Si votre nouvel appareil est endommagé :

Contactez immédiatement le revendeur (ou le fabricant).

Gagnez du temps et de l’argent :

Avant de faire appel à nos services, consultez à nouveau la section

« Dépannage ». Cette section vous aidera à résoudre des problèmes courants.

Si une réparation est nécessaire, ne vous inquiétez pas, la solution est au

bout du fil.

Tel: 1-800-26-

(1-800-263-2629)

La page charge ...

Danby DKC054A1BSLDB Manuel utilisateur

Marque: Danby

Modèle: DKC054A1BSLDB

Taper: Manuel utilisateur

Ce manuel convient également à

DKC054A1BSLDB

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DKC054A1BSLDB User manual
español: Danby DKC054A1BSLDB Manual de usuario

Danby DKC054A1BSLDB Manuel utilisateur

Ce manuel convient également à

Danby DKC054A1BSLDB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents