Danby DKC146SLDB Manuel utilisateur

Marque: Danby

Modèle: DKC146SLDB

Catégorie: Frigos

Taper: Manuel utilisateur

Model • Modèle • Modelo

v2 05.10 DM

• Owner’s Use and Care Guide

• Guide d’utilisation et d'entretien

• Manual de instrucciones

KEG COOLER

GLACIÈRE DE BIÈRE PRESSION

BARRIL REFRIGERADOR

DKC146SLDB

Danby Products Limited, Ontario, Canada N1H 6Z9

Danby Products Inc., Findlay, Ohio, USA 45840

GLACIÈRE DE BIÈRE PRESSION

Guide d'utilisation et d'entretien

• Consignes de sécurité importantes ....................

• Caractéristiques ..................................................

• Instructions d’installation ....................................

• Notice d’installation du baril à bière....................

• Utilisation ............................................................

• Soins et entretien ...............................................

• Dépannage .........................................................

• Garantie ..............................................................

Contents

3,4

6,7

7-11

12,13

BARRILREFRIGERADOR

Manual de uso y mantenimiento

• Instrucciones de seguridad importantes ............

• Caracteristicas ....................................................

• Instrucciones d'instalacion ..................................

• Instrucciones para la instalación

del barril de cerveza ...........................................

• Instrucciones de funcionamiento ........................

• Limpieza y mantenimiento ..................................

• Solucion sugeridad .............................................

• Garantia ..............................................................

CAUTION:

PRECAUTION:

ADVERTENCIA:

Read and follow all safety rules and

operating instructions before first use of this

product.

Veuillez lire attentivement les consignes de

sécurité et les instructions d’utilisation avant

l’utilisation initiale de ce produit.

Lea y observe todas las reglas de seguridad

y las instrucciones de operación antes de

usar este producto por primera vez.

Model • Modèle • Modelo DKC146SLDB

17,18

20,21

21-25

31,32

34,35

35-39

40,41

KEG COOLER

Owner’s Use and Care Guide

• Safety Instructions ...............................................

• Features ..............................................................

• Installation Instructions ........................................

• Beer Keg Installation Instructions .......................

• Operating Instructions .........................................

• Care and Maintenance ........................................

• Troubleshooting ...................................................

• Warranty ..............................................................

Welcome

Welcome to the Danby family. We’re proud of our quality products, and we believe in dependable service; like you will

find in this owner’s use and care guide, and like you will receive from our friendly customer service department. Best of

all, you will experience these values each and every time you use your Danby Keg Cooler. That’s important, because

your new appliance will be a part of your family for a long time.

For easy reference, may we suggest that you attach a copy of your sales receipt to this page, and note the information

below; you will need this information to obtain service under warranty.

Model No:

Serial No:

Date Purchased:

Before you call for service, there are a few things you can do to help us

serve you better.

Read this Owner’s Use and Care Guide:

It contains instructions to help you use and maintain your appliance

properly.

If you received a damaged appliance:

Immediately contact the builder (or dealer) that sold you the Beverage

Center.

Save time and money:

Check the Trouble shooting section before calling. This section helps you

solve common problems that may occur.

If you do need service, you can relax knowing help is only a phone call

away.

Need Help?

Tel: 1-800-26-

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

GROUNDING

INSTRUCTIONS

FOR YOUR SAFETY: Pertaining to the risk of Fire, Electric Shock or Injury to Persons.

• This appliance must be grounded. In the event of a malfunction or

breakdown, grounding will reduce the risk of electric shock by providing

a path of least resistance for electric current.

• This appliance is equipped with a power cord having an equipment

grounding conductor and grounding plug. The plug must be plugged into

an appropriate wall outlet that is installed and grounded in accordance

with all existing local codes and ordinances.

• Consult a qualified electrician or service person if the grounding

instructions are not clearly understood, or if doubt exist as to whether

your electrical wall outlets are properly grounded.

WARNING

If it becomes difficult to breathe and/or

your head starts to ache, abnormal con-

centrations of carbondioxide (CO2) may

be present in the area....

CLOSE THE MAIN VALVE ON THE

CO2 CYLINDER, VENTILATE AND

LEAVE THE ROOM IMMEDIATELY!

1. Always check the D.O.T.

(Department of Transport) as

well as the T.C. (Transport

Canada) testdate located on the

neckof the cylinder before

installation. If the date is older

than five (5) years,do not use,

return the gas cylinder to a gas

supplier for re-certification

(service charges may be

applicable).

2. Always connect a CO2 gas

cylinder to a regulator.Failure to

do so could result in an

explosion which can possibly

result in death or injury when the

cylinder valve is opened.

3. Never connect a CO2 gas

cylinder directly to beer keg.

4. Always secure a CO2 gas

cylinder in an "upright" position.

5. Always keep a CO2 gas cylinder

away from heat.

6. Never drop or throw a CO2 gas

cylinder.

7. Never connect a CO2 cylinder

unless there are two (2) safety

mechanism's in the pressure

system;

(a) One at or on the CO2 regulator.

(b) One at or on the product

container coupler in the

pressure gas line.

NOTE: The regulator andkeg

coupler supplied with this unit are

inclusive of such safety

mechanisms.

8. CO2 gas cylinders should be

stored in the coolest part of the

establishment (preferably) at

70ºF (21ºC) and must always be

securely fastened in an "upright"

position.

9. Always ventilate area after any

leakage of CO2.

WARNING CO CAN BE

DANGEROUS!

CO2 Cylinders when charged contain

high pressure compressed gas which can

be hazardous if not handled properly.

Read and understand the following

procedures for CO2 cylinders before

installation;

• This appliance must be connected to a properly grounded electrical

outlet (see Grounding Instructions)

• Do not operate this appliance if it has a damaged power cord or plug.

• Do no use this product near water, for example: in a wet basement, near

a swimming pool or sink.

• Do not defrost this appliance using other electric appliances (i.e. hair

dryer) and never attempt to scrape or remove ice/frost from the

evaporator (cold plate) with sharp objects.

• Always disconnect the appliance from the power supply before cleaning

and/or attempting repairs/servicing.

SAFETY

PRECAUTIONS

Repairs should be performed by qualified service personnel only.

IMPORTANT WARNING

• If you have purchased this appliance to replace an old one remove

either the gaskets, latches, lids or doors from the unused appliance. If it

was equipped with a door lock that cannot be opened from the inside,

(lock bolt) make sure the lock is removed, disabled or destroyed before

discarding, this will make it impossible for children to accidentally lock

themselves inside the appliance and suffocate.

• The refrigerator system of this appliance is filled with refrigerant and

insulating substances which should be treated and processed separately.

Call your nearest service agent or specialized servicing center. If you are

unable to locate one, contact your local authorities for proper disposal

instructions. Be careful not to damage any of the refrigeration lines of the

appliance.

DON’T WAIT DO THIS

NOW!

Improper disposal of worn out

appliances pose a risk of

entrapment to children.

Beer is easily available with Danby's new Keg Cooler, however, it is not

intended to be available to people under the legal age to consume beer. A

beer faucet lock kit for the purpose of limiting access, is readily available

and can be purchased through our after sales service department (see

‘Optional Accessories’ ). Danby does not assume liability for the unlawful

use or consumption of the beer.

PLEASE DRINK RESPONSIBLY AND PLEASE DON'T

DRINK AND DRIVE!

IMPORTANT

WARNING

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Features

CHILL N’ TAP ACCESSORIES

INCLUDED

ACCESSORIES

Remove and inspect all accessories supplied with this unit are present

and in good condition. In the event any of the accessories are missing

and /or not in good condition, please call Danby TOLL FREE at the

number listed below and speak with one of our Customer Service

Representatives. (1-800-263-2629)

BEER TOWER

ASSEMBLY

BACK

1. Beer Tower

2. Plastic Gasket

3. Safety Guard Rail

4. Drip Tray

5. Adjustable Thermostat

6. CO2 Regulator

7. CO2 Gas Cylinder

8. CO2 Gas Cylinder Support

9. Evaporator

10. Reversible Door

11. Beer Keg (not included)

12. Metal Plate

13. Castors (4)

Installation Instructions

BEFORE USING YOUR

BEER DISPENSER

• Remove the exterior and interior packing.

• Check to be sure you have all of the following parts:

• 1 Safety Guard Rail

• 1 Drip Tray (2 Pieces)

• 1 CO2 Cylinder Support

• 1 CO2 Regulator (Box)

• 1 CO2 Empty Cylinder(Box)

• 1 CO2 Air Line Hose (Red)

• 1 Beer Keg Coupler (Box)

• 1 Beer Tower

• 1 Pull Handle (Beer TowerFaucet)

• 4 Plugs: For Guard Rail Holes

• 1 Metal Plate For Cabinet Bottom

• 2 Steel wire shelves

• 1 Steel Clamp for Red Hose

• 4 Castors (2 front with locks)

• Before plugging in the keg cooler, let it stand upright for approximately 2

hours. This will reduce the possibility of a malfunction in the cooling

system from handling during transportation.

• Clean the interior surface with lukewarm water using a soft cloth.

INSTALLATION OF

BEER DISPENSER

• This appliance is designed to be free standing only, and should not be

recessed or built-in.

• Place your Beer Dispenser on a floor that is strong enough to support

the Beer Dispenser when it is fully loaded.

• Allow 3 inches of space between the back and sides of the Beer

Dispenser, which allows the proper air circulation to cool the compressor.

• Locate the Beer Dispenser away from direct sunlight and sources of heat

(stove, heater, radiator, etc.). Direct sunlight may affect the acrylic

coating and heat sources may increase electrical consumption. Extreme

cold ambient temperatures may also cause the Beer Dispenser not to

perform properly. This unit is not designed for outside installation (ie

garages, porches, etc.)

• Avoid locating the Beer Dispenser in excessive humidity.

• Plug the Beer Dispenser into a dedicated, properly installed-grounded

wall outlet. Do not under any circumstances cut or remove the third

(ground) prong from the power cord. Any questions concerning power

and or grounding should be directed toward a certified electrician or an

authorized service center.

• After plugging the appliance into a wall outlet, allow the unit to cool down

for 2-3 hours before placing any contents in the Beer Dispenser

compartment.

ELECTRICAL

CONNECTION

Improper use of the grounded plug can result in the risk of

electrical shock. If the power cord is damaged, have it replaced by

an authorized service center.

WARNING

This Beer Dispenser should be properly grounded for your safety. The

power cord of this Beer Dispenser is equipped with a three-prong plug

which mates with standard three prong wall outlets to minimize the

possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong

from the power cord supplied.

Use of extension cords is not recommended.

Installation Instructions

ELECTRICAL

CONNECTION (cont)

This Beer Dispenser requires a standard 115/120-volt, 60Hz electrical

outlet with three-prong ground receptacle. The cord should be secured

behind the Beer Dispenser and not left exposed or dangling to prevent

accidental injury.

Never unplug the Beer Dispenser by pulling the power cord. Always grip

the plug firmly and pull straight out from the receptacle.

CO2 GAS CAN BE DANGEROUS

CO2 cylinders contain high-pressure compressed gas which can

be hazardous if not handled properly. Make sure you READ and

UNDERSTAND the following procedures for CO2 cylinders

BEFORE INSTALLATION.

WARNING

1. ALWAYS connect the CO2 cylinder to a regulator. Failure to do so

could result in explosion with possible injury when the cylinder valve is

opened.

2. NEVER connect the CO2 cylinder directly to the product container.

3. ALWAYS follow correct procedures when cylinders are changed.

4. ALWAYS secure the cylinder in an upright position.

5. NEVER drop or throw a CO2 cylinder.

6. ALWAYS keep a CO2 cylinder away from heat. Store extra cylinders in

a cool place (preferably 70°F). Securely fasten with a chain in an

upright position when storing.

7. ALWAYS ventilate and leave the area immediately if CO2 leakage has

occurred.

8. ALWAYS check the D.O.T. test date on the cylinder neck before

installation. If over five (5) years, do not use, return cylinder to gas

supplier.

9. NEVER connect a product container unless there are two (2) safety’s in

the pressure system:

a. One at or on the CO2 regulator

b. One at or on the product coupler or in the pressure gas line.

Beer Keg Installation Instructions

CO2 TANK

RED PRESSURE HOSE

KEG

AMERICAN

SANKEY TAP

CLEAR HOSE

WITH WING NUT

TOWER

FAUCET ASSEMB

SINGLE GAUGE

PRESSURE

REGULATOR

TOWER

Keg Installation Sketch

• Install the four castors (2 locking castors at front) into the unit’s bottom

(four screw holes pre-supplied) Figure (1) before installation. Figure (II)

is the final version.

METAL

WASHERS

Figure 1 Figure 2

CASTORS

Beer Keg Installation Instructions

CASTOR BRAKE GUIDE

STEP ON TO BRAKE

STEP ON TO RELEASE

BRAKE

INSTALLATION OF CO2

CYLINDER SUPPORT

• Install the metal support provided onto the 4 studs located on the exterior

back wall. Align the holes in the support with the studs and push down

firmly. (See Figure 1)

Figure 1 Figure 2 Figure 3

INSTALLATION OF CO2

CYLINDER

• The CO2 Cylinder does not come filled. The cylinder must be filled with

CO2 prior to use.

• Install your fully charged cylinder into the support stand.

INSTALLATION OF CO2

REGULATOR

• Attach the CO2 regulator to the cylinder by turning the regulator nut onto

cylinder valve, making sure washer is securely inserted into connecting

nut. Tighten snug using an adjustable wrench (not supplied) and assure

there are no leaks. (See Figure 2)

INSTALLATION OF CO2

AIR LINE OUTSIDE

CABINET

• Remove plug located at the exterior back (top left hand corner).

• Save it for later use if you decide to convert unit to a refrigerator.

• Insert the open end of the air line (red) line the cabinet through the

uncovered hole. (See Figure 4)

Beer Keg Installation Instructions

INSTALLATION OF CO2

AIR LINE HOSE TO

REGULATOR

• Attach the open end of the red hose to the hose barb connection on the

regulator

• Secure hose by using one clamp provided. Use pliers/screwdriver to

tighten clamp to prevent leaks. (See Figure 3)

INSTALLATION OF THE

BEER TOWER

• Remove the top plug by twisting and pulling out, saving it for later use if

you decide to convert unit to an all refrigerator unit.

• Unravel the beer line (clear hose) from the tower and insert the beer line

and wing nut through the uncovered hole on top.

• Lock the beer tower assembly to the top and make sure to position the

beer faucet so it is aligned with the cabinet front (6 o’clock position). You

accomplish this by aligning the bottom of the beer tower to the 3 grooves

on the top cabinet and tighten by hand clockwise to properly lock.

• The plastic gasket (# 2 in parts list), can be used to make the connection

between the tower and the cooler tighter if needed. If Beer Tower will not

turn to lock in place, try removing the plastic gasket.

INSTALLATION OF

PROTECTIVE METAL

PLATE

• This plate should always be installed when the keg is in place to protect

against unnecessary damage to the floor of the cabinet.

INSTALLATION OF THE

BEER KEG

• Position the beer keg directly in front of the open door. Using keg

handles only, carefully lift the beer keg. (See Figure 5)

• To place the beer keg inside the cabinet, brace your knees behind the

beer keg. Lift the front of the keg just enough so the front edge of the

keg is resting on the front edge of the Beer Dispenser bottom cabinet.

(See Figure 6)

• Grasp the keg handles and slide it all the way into the cabinet.

Figure 4

Figure 5 Figure 6

INSTALLATION OF THE

KEG COUPLER

• Insert the keg coupler provided into the locking neck of the beer keg and

turn it clockwise to lock into position, making sure the keg coupler is in

the closed position. (See Figure 7)

INSTALLATION OF THE

CO2 AIR LINE HOSE

• Attach the end of the air line (red) hose provided to the hose connection

on the keg coupler.

Beer Keg Installation Instructions

CONNECTING THE BEER

TOWER TO COUPLER

• Make sure the washer is properly inserted into the wing nut.

• Make sure the small round bead is in place (dropped down into the top

of the coupler).

• Make sure the ball retainer is in place on the coupler, with the ‘arms’

down into the coupler.

• Place wing nut into the top of the coupler turning until tight.

HOW TO TAP A KEG OF

BEER

• Make sure that the CO2 is turned off, and the Secondary valve on the

regulator is in the ‘Closed’ position.

• Pull out and release the pressure release valve on the Coupler to purge

any air pressure.

• Make sure the beer tower faucet is in the closed position.

• Pull tapping handle out and press downward until it locks into position.

(See Figure 8) The keg is now tapped.

OPENING THE CO2

CYLINDER MAIN VALVE

• Make sure the secondary shut-off valve (shown in figure 9 in ‘Open’

position) is closed. To open the main CO2 cylinder valve, slowly turn the

main valve counter-clockwise until fully open.

• Notice the needle on the regulator gauge start to climb.

ADJUSTING THE CO2

REGULATOR

The gauge monitors low internal keg pressure and should be adjusted to

read between 10-12 psi. (See Figure 10). The pressure can be adjusted

as needed.

• Release adjustment lock nut marked 2.

• Using a flat screwdriver, turn regulator screw marked 3.

o To increase pressure, turn screw clockwise.

o To decrease pressure, turn screw counter - clockwise.

• Retighten lock nut marked 2.

• Open secondary shut off valve to let CO2 flow into the keg.

• Allow several minutes for the keg to properly pressurize. Regulator

gauge may drop while this happens. (Note: Listen for hissing along all

connections to identify if there are any leaks)

Figure 7

Figure 8

Figure 9 Figure 10

Beer Keg Installation Instructions

SPANNER FAUCET

WRENCH (Not Included)

Spanner faucet wrench (not provided) is for either removing or tightening

the connection.

PLASTIC FAUCET

LEVER

Attach the black plastic lever (pull handle) to the top of the faucet by

tightening it by hand clockwise until the end, holding in the silver nut

underneath so it does not turn. If there is still a small drip from the faucet,

you may have tightened the plastic lever too much and may need to

unscrew silver snug counter-clockwise (as shown) one turn.

DISPENSING OF BEER

• Keep beer keg refrigerated at all times.

• Never allow beer lines to dry out.

• Use clean beer glassware before pouring.

• Hold glass at a 45° angle when 2/3 full, start to straighten glass as the

glass fills.

• Always make sure the faucet handle is pushed all the way back.

Note: Keg sizes that can be used in your beer dispenser

1/2 barrel 59 Liters 15.5 gals 1984 oz. 164/12-oz. Glass

1/4 barrel 30 Liters 7.8 gals. 992 oz. 82/12-oz. Glass

1/6 barrel 20 Liters 5.2 gals. 661 oz. 55/ 12-oz. Glass

1/8 barrel 15 Liters 4.0 gals. 496 oz. 41/ 12-oz. Glass

Note: Our Beer dispenser accepts standard kegs up to 16-1/8” in

diameter, and up to 23-3/8” in height. Check with your distributor to make

sure keg is correct size.

Operating Instructions

SETTING THE

TEMPERATURE

The temperature is controlled by adjusting/setting the thermostat control

knob. To start the unit and achieve maximum cooling quickly;

• Turn the temperature control knob clockwise to the furthest (maximum)

setting on the blue (wide) section of the control dial. (Fig A)

• Allow the unit to run at this setting for 3-4 hours.

• When maximum cooling is achieved, turn back the temperature control

knob to a moderate/medium temperature.

• To turn off (no cooling) rotate the control knob to the “0” (off)

position. (Fig.B.)

AUTOMATIC

DEFROSTING

There is no need to defrost the Beer Dispenser. Defrost water collects and

passes thru the drain outlet in the rear wall into a tray located above the

compressor, where it evaporates.

NOTE: If the unit is unplugged, power lost, or turned off; you must wait 3

to 5 minutes before restarting the unit. If you attempt to restart before this

time delay, the Beer Dispenser may not start.

CONVERTING TO AN

“ALL REFRIGERATOR”

1. Turn off the control knob to the “OFF” position.

2. Close the main valve on the CO2 cylinder.

3. Close the secondary shut-off valve on the regulator pipe.

4. Close the connection between the beer keg and the keg coupler.

5. Drain any remaining beer from the lines.

6. Disconnect the beer line and CO2 air line from the keg coupler

7. Remove the beer keg.

8. Remove the keg coupler.

9. Disconnect the air line from the CO2 cylinder.

10. Remove the CO2 air line from cabinet plug

11. Replace the air line rear cabinet plug

12. Remove the beer tower. Also pull the beer line thru the top of the

cabinet

13. Replace the top cabinet plug

14. Adjust temperature as desired.

Fig B.

Fig A.

Operating Instructions

CHANGING THE

REVERSIBLE DOOR

This Beer Dispenser has a door that can be set to open from the left or

right side. The unit is delivered to you with the door opening from the left

side. To reverse the opening direction, please follow the instructions

below.

To avoid personal injury to yourself and/or property, we

ecommend that someone assist you during the door reversal

process.

CAUTION

Undo the three screws in each

bracket using the Phillips

screwdriver.

Remove the screws and bracket.

Place to one side.

Slide the Larder Fridge door down

about 15cm (6’’) and off the top

hinge pin and lift away from the

freezer.

Using the flat bladed screw driver

remove the pin from the top bracket.

Replace it in the hinge bracket on

the opposite side.

Remove the screw from the side of

the Larder Fridge where the

bracket is to be re-fitted.

Slide the Larder Fridge door back

on to the top hinge, making sure it’s

the right way up. Screw the bottom

hinge into place on the new side.

Check that the door is aligned

horizontally and vertically and

that the seals are closed on all

sides before finally tightening

the bottom hinge. Re-adjust

the leveling feet.

Care and Maintenance

Troubleshooting

CLEANING YOUR BEER

DISPENSER

• Turn the temperature control to "OFF", unplug the Beer Dispenser, and

remove the contents.

• Wash the inside surfaces with a warm water and baking soda solution.

The solution should be about 2 tablespoons of baking soda to a quart of

water.

• Wash the shelves and stand with a mild detergent solution.

• Wipe down any electrical controls with a dry clothe.

• Wash the outside cabinet with warm water and mild liquid detergent.

Rinse well and wipe dry with a clean soft cloth.

VACATION TIME

• Short vacations: Leave the Beer Dispenser operating during vacations of

less than three weeks.

• Long vacations: If the appliance will not be used for several months,

remove all contents and unplug the power cord. Clean and dry the

interior thoroughly. To prevent odor and mold growth, leave the door

open slightly.

MOVING YOUR BEER

DISPENSER

• Remove all the contents.

• Securely tape down all loose items inside your Beer Dispenser.

• Tape the door shut.

• Be sure the Beer Dispenser stays secure in the upright position during

transportation. Also protect outside of Beer Dispenser with a blanket or

similar item.

You can solve many common Beer Dispenser problems easily, saving you the cost of a possible service call. Try the

suggestions below to see if you can solve the problem before calling the servicer.

Beer Dispenser does not operate

Turns on and off frequently

Vibrations

The Beer Dispenser seems to make too

much noise.

The door will not close properly.

PROBLEM

POSSIBLE CAUSE

Not plugged in.

The circuit breaker tripped or blown fuse.

The room temperature is hotter than normal.

The door is open too often.

The door is not closed completely.

The temperature control is not set correctly.

The door gasket does not seal properly.

The unit does not have proper clearance.

Check to assure that the Beer Dispenser is level.

The rattling noise may come from the flow of the refrigerant, which is

normal.

Gurgling, caused by liquid refrigerant cycling, is normal.

Contraction and expansion of the inside walls may cause popping and

crackling noises.

The Beer Dispenser is not level.

The door was reversed and not properly installed.

The gasket is dirty.

The shelves or stand are out of position.

The Keg is not properly centered in the unit.

The Castors are not attached.

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the first twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any appliance

Service

requiring service outside the limited boundaries of “In Home Service” ,it will be the consumer’s responsibility to transport the appliance

(at their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Service” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualified service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial application, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualified and certified for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are the

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other contents of this appliance, whether

due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditions, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating conditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

Bienvenue

Bienvenue dans la famille Danby. Nous sommes fiers de nos produits de qualité et croyons au bien fondé de fournir une

assistance fiable à nos clients. Vous le découvrirez grâce à ce guide facile d’utilisation et vous pourrez l’entendre en

provenance des voix amicales de notre service d’assistance à la clientèle.

Mais, ce qui est encore mieux, vous pourrez bénéficier de ces valeurs à chaque utilisation de votre appareil. Ceci est

important parce que votre nouvel appareil fera partie de votre famille pour longtemps.

Numéro de modèle :

Numéro de série :

Date d’achat :

Voici quelques petites choses que vous pouvez effectuer avant de faire un

appel de service, pour nous aider à mieux vous servir:

Lisez ce guide :

Il comprend des instructions pour vous assister avec l’utilisation et

l’entretien adéquats de votre refroidisseur de boissons.

Si votre appareil neuf esta varié :

Communiquez immédiatement avec le revendeur (ou le manufacturier).

Épargnez temps et argent :

Avant de faire un appel de service, résoudre le chapitre intitulé

“Dépannage”. Ce chapitre vous aidera à résoudre des problèmes communs

qui pourraient survenir. Si vous avez besoin de notre aide, vous pouvez

être assuré que nous serons au bout du fil.

Tel: 1-800-26-

(1-800-263-2629)

Besoin d'aide?

Consignes de sécurité importantes

PRENDRE CONNAISSANCE DE TOUTES LES INFORMATIONS

RELATIVES À LA SÉCURITÉ AVANT D'UTILISER LE PRODUIT

CONSIGNES DE MISE À

LA TERRE

Cet appareil doit être mis à la terre. En cas de court-circuit, la mise à la terre réduit les risques de décharge électrique

en fournissant un échappatoire au courant électrique. L’appareil est muni d’un cordon électrique comprenant un fil de

mise à la terre et une fiche de terre.

• Cet appareil doit être mis à la terre. Dans le cas d’un mauvais

fonctionnement ou d’un bris, la mise à la terre réduit le risque de choc

électrique en permettant au courant électrique d’emprunter le chemin offrant

le moins de résistance.

• Cet appareil est doté d’un cordon d’alimentation avec équipement

conducteur de mise à la terre et fiche bipolaire avec terre. La prise doit être

branchée dans une prise adéquate, installée et mise à la terre selon la

réglementation locale.

• Consultez un électricien qualifié ou un technicien si les directives de mise à

la terre ne sont pas entièrement comprises, ou si un doute subsiste quant à

la mise à la terre appropriée des prises murales.

AVERTISSEMENT

S’il est difficile de respirer ou si un mal de

tête vous prend, il est possible que des

concentrations anormales de gaz

carbonique se trouvent dans la pièce…

FERMEZ LA VALVE PRINCIPALE DE LA

BOUTEILLE DE GAZ CARBONIQUE,

AÉREZ LA PIÈCE ET QUITTEZ-LA

IMMÉDIATEMENT!

1. Branchez toujours la bouteille de

gaz carbonique à un régulateur.

Sans quoi, l’ouverture de la valve

de la bouteille pourrait causer une

explosion qui risque d’entraîner la

mort ou des blessures.

2. Ne branchez jamais la bouteille de

gaz carbonique directement sur le

fût de bière.

3. Fixez toujours la bouteille de gaz

carbonique en position verticale.

4. Gardez toujours la bouteille de gaz

carbonique à l’abri de la chaleur.

5. Ne laissez jamais tomber et ne

lancez jamais une bouteille de gaz

carbonique.

6. Avant de l’installer, vérifiez toujours

la date d’essai du D.O.T. (Ministère

des transports), située sur le col

de la bouteille. Si l’essai a eu lieu il

y a plus de cinq (5) ans, retournez

la bouteille de gaz à votre

fournisseur.

7. Ne branchez jamais une bouteille

dont le mécanisme de pression ne

présente pas deux (2)

mécanismes de sécurité :

(a) un au niveau du régulateur de

gaz carbonique;

(b) un au niveau du coupleur de la

bouteille, sur la conduite de

pression du gaz.

Le régulateur et le coupleur de fût

compris avec cet appareil constituent

de tels mécanismes de sécurité.

8. Les bouteilles de gaz carbonique

doivent être rangées

préférablement dans les pièces les

plus froides de l’établissement, à

70° F (21° C). Elles doivent

toujours être fixées en position

verticale.

9. Aérez toujours la pièce après une

fuite de gaz carbonique.

AVERTISSEMENT :

LE GAZ CARBONIQUE

PEUT ÊTRE

DANGEREUX!

Les bouteilles de gaz carbonique chargées

contiennent du gaz hautement pressurisé,

qui peut présenter un danger s’il n’est pas

manipulé correctement. Avant l’installation,

lisez et assurez-vous de bien comprendre

les procédures suivantes concernant les

bouteilles de gaz carbonique:

Consignes de sécurité importantes

• Cet appareil doit être branché à une prise électrique correctement mise à la

terre (voir Instructions de mise à la terre)

• N’utilisez pas cet appareil si son cordon ou sa fiche sont endommagés.

• N’utilisez pas ce produit près d’une source d’eau, tel un sous-sol humide,

une piscine ou un évier.

• Ne faites pas dégeler cet appareil à l’aide d’autres appareils électriques

(ex. : séchoir à cheveux) et ne grattez jamais la glace ou le givre de

l’évaporateur (plaque froide) à l’aide d’un objet coupant.

• Débranchez toujours l’appareil de la prise d’alimentation avant de le nettoyer

ou de tenter de le réparer.

CONSIGNES DE

SÉCURITÉ

Toute réparation doit être effectuée par le personnel qualifié

seulement.

AVERTISSEMENT

• Si vous avez achetez cet appareil afin d’en remplacer un vieux, retirez les

joints, verrous, couvercles ou les portes de l’appareil non utilisé. S’il était

équipé d’un verrou ne pouvant être ouvert de l’intérieur (boulon de blocage),

assurez-vous que le verrou est retiré, mis hors service ou détruit avant la

mise aux rebuts. Ceci empêchera les enfants de s’enfermer

accidentellement dans l’appareil et d’y étouffer.

• Le système de refroidissement de cet appareil est rempli de substances

réfrigérantes et isolantes devant être traitées séparément. Appelez votre

représentant de service ou un centre d’entretien spécialisé. Si vous êtes

incapable d’en trouver un, contactez votre autorité locale afin d’obtenir les

directives de mise aux rebuts appropriée. Prenez soin de ne pas

endommager les lignes de réfrigération de l’appareil.

N’ATTENDEZ PAS :

FAITES-LE

IMMÉDIATEMENT!

Une mauvaise mise aux rebuts

d’appareils usés constitue un risque

de piège pour les enfants.

La bière est facile d’accès avec la nouvelle glacière de bière pression de

Danby. La glacière n’est cependant pas conçue pour offrir de la bière aux

personnes n’ayant pas l’âge légal pour consommer. Un jeu de verrouillage du

robinet permettant de restreindre l’accès à la bière est disponible et peut être

acheté auprès de notre service des ventes (voir Accessoires facultatifs).

Danby n’est pas responsable de la consommation ou utilisation illégales de la

bière.

RAPPELEZ-VOUS : LA MODÉRATION A BIEN MEILLEUR GOÛT! LE

VOLANT ET L’ALCOOL NE FONT PAS BON MÉNAGE!

AVIS IMPORTANT

Caractéristiques

BEER TOWER

ASSEMBLY

BACK

ACCESSOIRES DE LA GLACIÈRE

ACCESSOIRES

FOURNIS

Enlevez et inspectez tous les accessoires fournis avec cet appareil pour vous

assurer qu’ils sont présents et en bon état. Si certains accessoires manquent

ou ne sont pas en bon état, veuillez appeler Danby au numéro SANS FRAIS

indiqué ci-dessous pour parler à l’un de nos représentants du service à la

clientèle. (1-800-263-2629)

1. Colonne de bière

2. Joint en plastique

3. Barre de retenue

4. Plateau perforé

5. Thermostat réglable

6. Régulateur de CO2

7. Bouteille de CO2 gazeux

8. Support de la bouteille de CO2 gazeux

9. Évaporateur

10. Porte réversible

11. Baril à bière (non fourni)

12. Plaque métallique

13. Roulettes (4)

Assemblage de la

colonne de bière

Vue arrière

La page charge ...

Danby DKC146SLDB Manuel utilisateur

Marque: Danby

Modèle: DKC146SLDB

Catégorie: Frigos

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DKC146SLDB User manual
español: Danby DKC146SLDB Manual de usuario

Danby DKC146SLDB Manuel utilisateur

Danby DKC146SLDB Manuel utilisateur

dans d''autres langues

Documents connexes