GE Profile PXRQ15F Manuel utilisateur

ge.com
Reverse Osmosis
101019-A      215C1174P003      49-50198 01-06 JR
Filtration System
PXRQ15F
PNRQ15FBL
Owner’s Manual
and Installation
Safety Instructions
Safety Instructions  . . . . . . . . . . . . . .2
Specification Guidelines  . . . . . . . . .3
Operating Instructions
About the RO System  . . . . . . . . .4, 5
Installation Instructions
Tools and Materials Required  . . . . .6
Before Beginning Installation  . . .6, 7
Mounting System Installation  . . . . .8
Feed Water Supply . . . . . . . . . . .9–12
Faucet Assembly . . . . . . . . . . . .13, 14
Battery Installation  . . . . . . . . . . . .14
Filtration Drain Connection  . .15, 16
Storage Tank and Startup  . . . . . . .17
Care and Cleaning
Prefilter, Postfilter and 
RO Cartridge Replacement . . . . . .18
Sanitization  . . . . . . . . . . . . . . . . . .19
Water Test Kit  . . . . . . . . . . . . . . . .20
Troubleshooting Tips  . . . . . .21, 22
Consumer Support
Consumer Support  . . . . .Back Cover
Parts List/Catalog  . . . . . . . . . .24, 25
Warranty  . . . . . . . . . . . . . . . . . . . .26
Manuel d’utilisation 
et d’installation
Manual del propietario
y instalación
La section française commence à la page 27
Osmose Inversée
Système de Filtration
La sección en español empieza en la página 55
Ósmosis Inversa
Sistema de Filtración
Tested and Certified by NSF International to
NSF/ANSI Standard 58. For the reduction of the
claims specified, see the Performance Data Sheet.
Essayé et certifié par NSF International
conformément aux normes 58 NSF/ANSI. Pour 
la réduction des caractéristiques indiquées,
consultez la feuille de données de rendement.
Probado y certificado por NSF International por
cumplir con el estándar 58. Para la reducción de
reclamos especificados, ver la hoja de datos de
desempeño.
Write the model and serial
numbers here:
Model # __________________
Serial # __________________
You can find them on the bracket.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

■ Check with your state and local public works

department for plumbing and sanitation codes.

You must follow these guidelines as you install the

Reverse Osmosis system. Using a qualified installer

is recommended.

■ If house water pressure is over the maximum

(120 pounds per square inch), install a pressure

reducing valve in the water supply line to the

Reverse Osmosis system.

■

Be sure the water supply conforms with the

Specification Guidelines. If the water supply conditions

are unknown, contact your municipal water company

or your local health department for a list of

contaminants in your area and a list of laboratories

certified by your state to analyze drinking water.

WARNING: Before using the Reverse Osmosis

system for the first time, the system must be

purged. The Reverse Osmosis cartridge contains

a food grade preservative that must be purged

from the system. The preservative will give product

water an unpleasant taste and odor.

WARNING: Do not use with water that is

microbiologically unsafe or of unknown quality

without adequate disinfection before or after the

system. Systems certified for cyst reduction may

be used on disinfected water that may contain

filterable cysts.

This system has been tested for the treatment of

water containing pentavalent arsenic (also known

as As(V), As(+5) or arsenate) at concentrations

of 0.050 mg/L or less. This system reduces

pentavalent arsenic, but may not remove other

forms of arsenic. This system is to be used on water

supplies containing a detectable free chlorine

residual or on water supplies that have been

demonstrated to contain only pentavalent arsenic.

Treatment with chloramine (combined chlorine)

is not

sufficient to ensure complete conversion of

trivalent arsenic to pentavalent arsenic. Please see

the Arsenic Facts section of the Performance Data

Sheet for further information.

This reverse osmosis system contains a replaceable

component critical to efficiency of the system.

Replacement of the reverse osmosis component

should be with one of identical specifications, as

defined by the manufacturer, to assure the same

efficiency and contaminant reduction performance.

SAVE THESE INSTRUCTIONS

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

■ Install or store where it will not be exposed to

temperatures below freezing or exposed to any type

of weather. Water freezing in the system will

damage it. Do not attempt to treat water over 100°F.

■ Do not install on HOT WATER. The temperature

of the water supply to the Reverse Osmosis system

must be between the minimum of 40°F and the

maximum of 100°F. See the Specification Guidelines.

■ Extended non-use of the Reverse Osmosis system.

If the system has not been used for one week or

more, open the RO water faucet and allow the

system to drain. Close the RO water faucet and

allow the system to regenerate the water supply.

■ Recommended installation is under the sink.

However, the unit can be installed in a remote

location, up to 20 feet away from the sink.

• However, additional materials will be required.

See parts list to obtain additional materials

from GE.

• Locating the tank on a basement floor, with the

faucet at a first floor sink may result in some loss

of flow rate and capacity (approximately 20%).

Installing a second tank will improve this

performance. An RVKIT can be used.

■ If Reverse Osmosis system is connected to a

refrigerator icemaker, a special icemaker

connection kit is required (RVKIT). Do not use

copper tubing for the connection between the

Reverse Osmosis system and the refrigerator.

WARNING: Discard all unused parts and packaging

material after installation. Small parts remaining after

the installation could be a choke hazard.

■

Sanitize upon installation of the Reverse Osmosis

system and after servicing inner parts, including

replacement of prefilter, postfilter and Reverse

Osmosis cartridge. It is important to have clean

hands while handling inner parts of the system.

See the Sanitizing the Reverse Osmosis System section.

■

This Reverse Osmosis system contains a replaceable

treatment component critical for effective

reduction of total dissolved solids. This product

water shall be tested periodically to verify that the

system is performing satisfactorily. See the About

the Water Test Kit section.

BE SURE TO FOLLOW ALL APPLICABLE STATE

AND LOCAL CODES.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of

property damage or personal injury.

SAFETY PRECAUTIONS

PROPER INSTALLATION AND MAINTENANCE

This Reverse Osmosis system must be properly installed and located in accordance with the

Installation

Instructions before it is used.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions

Installation Instructions

Specification guidelines.

ge.com

The system makes a good supply of drinking water each day.

How much it will make depends primarily on these things…

Product – height 11 ″ width 10.5 ″ depth 4 ″

Incoming Water pH

WATER SOFTENER RECOMMENDED

INCOMING WATER HARDNESS (GPG)

60

50

40

30

2010

8

6

7

7.5

6.5

Water Softener

not required

Maximum iron, manganese, hydrogen sulfide (ppm) . . . . . . . . . . . . . . . . . . . . . .<0.1

Chlorine in water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0 ppm Maximum Allowable

b

Feed water pH limits (pH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–10

Storage tank capacity—gallons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

c

Automatic shutoff control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .yes

Prefilter and postfilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(FQROPF) Carbon Block

Reverse Osmosis membrane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(FQROMF) Thin Film Polyamide

Storage Tank Dimension (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .height 15” diameter 11”

System Body Dimension (inches) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .height 11” width 10.5” depth 4”

Feed water pressure limits—pounds per square inch (psi) . . . . . . . . . . . . . . . . . . . . . .40–120

a

Feed water temperature limits—minimum/maximum degrees F . . . . . . . . . . . . . . . . .40–100

Maximum Total Dissolved Solids (TDS)—parts per million (ppm) . . . . . . . . . . . . . . . .2000

Maximum water hardness @ 6.9 pH recommended to optimize membrane

life—grains per gallon (gpg) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

For water with hardness greater than 10 grains (at 6.9 pH), the use of a

softener is recommended. Failure to install a water softener will reduce

the life of the Reverse Osmosis membrane. See chart for additional

information on the possible need for a water softener.

a. If house water pressure is over 120 psi, install a pressure reducing valve in the water supply line. If house water pressure

is under 40 psi, install a Reverse Osmosis booster pump (contact your local plumbing supply company).

b. Removed (maximum of 2.0 ppm) by the Reverse Osmosis prefilter. REGULAR MAINTENANCE IS REQUIRED. Chlorine will

destroy the Reverse Osmosis membrane.

c. Theoretical tank capacity. When tested according to NSF/ANSI Standard 58 at 50 psig inlet pressure, tank capacity is

2.3 gallons.

3

4

About the reverse osmosis system.

How the Reverse Osmosis System Works

Description of the Reverse Osmosis System

Reverse Osmosis reduces Total Dissolved Solids (TDS) and organic matter from water by diffusing it through a special

membrane. The membrane separates minerals and impurities from the water and they are flushed to the drain. For the

reduction of the claims specified, see Performance Data Sheet. High quality product water goes directly to the drinking

water faucet or to the storage tank. The system makes a good supply of drinking water each day. How much it makes

depends on the feed water supply pressure, temperature and quality.

The prefilter and postfilter are replaceable cartridges. The carbon prefilter reduces chlorine while also filtering sediments.

The postfilter reduces any other undesirable tastes and odors before you use the water.

The system includes an electronic faucet assembly with a prefilter and postfilter change reminder. When six months have

passed, a flashing blue light will remind you to change the two filters.

Troubleshooting TipsConsumer Support Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Prefilter—Water from the cold supply pipe is directed to the

prefilter cartridge. The prefilter is a replaceable sediment

cartridge containing activated carbon. The prefilter reduces

chlorine in the feed water because CHLORINE DESTROYS THE

REVERSE OSMOSIS MEMBRANE. Filtered, clean, chlorine-

reduced water flows from the prefilter to the Reverse

Osmosis cartridge.

Reverse Osmosis Cartridge—The middle cartridge includes a

tightly wound, special membrane. Water is forced through the

cartridge where the membrane reduces the dissolved solids and

organic matter. High quality product water exits the Reverse

Osmosis cartridge and goes to the storage tank. Reject water,

with the dissolved solids and organic matter, leaves the cartridge

and is discharged to the drain through 1⁄4″ tubing.

Postfilter—After leaving the storage area, but before going

to the system faucet, product water goes to the postfilter

cartridge. The postfilter is also a replaceable sediment cartridge

that contains activated carbon. Any remaining tastes, odors or

sediments are reduced from product water by the postfilter.

Clean, high quality drinking water flows through the tubing

and to the system faucet.

Storage Tank—The storage area holds up to 2-1/2 gallons

of product water. A diaphragm inside the tank keeps water

pressurized, when the tank is full, for fast flow to the faucet

when drinking water is needed.

4

3

2

1

5

ge.com

Check Valve—The check valve prevents a backward flow of product water from the storage tank. A backward flow could

cause the Reverse Osmosis membrane to rupture.

Automatic Shutoff Assembly—To conserve water, the drinking water system has an automatic shutoff. When the storage tank

has filled to capacity and the drinking water faucet is closed, pressure closes the shutoff. Water flow to the Reverse Osmosis

housing is shut off until drinking water is used again, and pressure drops in the Reverse Osmosis system.

Flow Control—The flow control regulates the flow of water through the Reverse Osmosis cartridge at the required rate to

produce high quality water. The control is located in the 1/4″ drain line exiting off the manifold.

Faucet and Electronics—The countertop faucet dispenses filtered drinking water when opened. It has a hand-operated

lever, with variable flow adjustment. You can keep the faucet open by removing your hand from the lever once water is

flowing.

To comply with plumbing codes, an air gap is built into the faucet drain water connection.

8

7

6

5

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

The electronic faucet provides a six month timer to remind you when it is time to replace your prefilter and postfilter.

Replace the filters when the blue light begins to flash in order to protect the RO membrane and keep the system

functioning properly.

Installation

Reverse Osmosis Filtration System

Instructions

Models PXRQ15F and PNRQ15FBL

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

BEFORE BEGINNING INSTALLATION

Read these instructions completely

and carefully.

•

IMPORTANT

— Save these

instructions for local inspector’s use.

•

IMPORTANT

— Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation

is not covered under the Warranty.

• A shutoff valve must be available or added

near the installation point.

TOOLS AND MATERIALS

REQUIRED FOR INSTALLATION

• Electric drill and 1-1/4″ Drill Bit (type as

required) if mounting is needed for faucet

• Two (2) Adjustable Wrenches

• 1/16″ Drill Bit (optional for pilot holes)

• Tape Measure

• Phillips and Flat Blade Screwdrivers

• Utility Knife

• If your main water line is a rigid pipe,

you will require a compression fitting

and possibly other plumbing hardware

to complete the installation.

CAUTION: To avoid damaging the

sink, consult a qualified plumber or installer

for drilling procedures. Special drill bits may

be needed for porcelain or stainless steel.

CONTENTS INCLUDED

WITH PRODUCT

• Reverse Osmosis Assembly and Tubing

• Product Literature (Owner’s Manual and

Installation Instructions)

• Performance Data Sheet

• Feed Water Adapter and Supply Valve

• Faucet Assembly with Electronic Base

Monitor and Tubing

• Storage Tank

• Drain Line Adapter

6

WARNING:

Read entire manual. Failure to follow all guides and rules could cause

personal injury or property damage.

• Check with your state and/or local public works department for plumbing codes. You must

follow their guides as you install the Water Filtration system.

NOTE: Failure to comply with these installation instructions will void the product warranty, and

the installer will be responsible for any service, repair or damages caused thereby.

Installation Instructions

Things to Check Before Beginning Installation

FEED WATER

The water supply to the undercounter Reverse

Osmosis system must have the qualities listed

in the specifications. Municipal water supplies

most often will have these qualities. Well

water may need conditioning—have the water

tested by a water analysis laboratory and get

their recommendations for treatment.

CAUTION: For water with a

hardness greater than 10 grains (at 6.9 pH),

the use of a softener is recommended. Failure

to install a softener will reduce the life of the

Reverse Osmosis cartridge.

FILTRATION DRAIN CONNECTION

A suitable drain point and air gap (check your

state and/or local codes) are needed for reject

water from the Reverse Osmosis membrane

cartridge.

BASEMENT INSTALLATION

If installing in a basement, leave enough

tubing in place during installation to be able

to move unit to floor for ease at servicing and

making filter/membrane changes. Additional

tubing and fittings required.

NOTE: See parts list on page 25 for optional

parts that may be required for a basement

installation.

RO FAUCET

The RO product water faucet installs on the

sink or on the countertop next to the sink.

Often, it is installed in an existing sink spray

attachment hole or a hole may be drilled.

Space is required underneath for tubing to

and from the faucet, and for securing the

faucet in place. All faucet connections are

done on or above the sink or countertop.

Sink

p-trap

Hot Cold

Disposer

1/4″ drain

tube (black)

3/8″ outlet tube (blue banded)

1/4″ inlet tube

(yellow banded)

Reverse osmosis system

3/8″ storage

tank tube

(red banded)

11″ dia. 10-1/2″

15″

11″

7″

3/8″ drain tube (black)

RO product water faucet mounted through sink or countertop

Feed water adapter

Prefilter PostfilterMembrane

1/4″ yellow

banded inlet

from supply

valve

1/4″ black

tube to

faucet

3/8″ red

banded tube

to storage

tank

3/8″ blue

banded

tube to

faucet

7

TUBING/FILTER DETAIL

Installation Instructions

REVERSE OSMOSIS ASSEMBLY

MOUNTING SYSTEM

INSTALLATION

Choose a location under the sink to mount

the system. Location should be easily

accessible, with adequate clearance between

the bottom of the filter cartridges and the

floor or bottom of the cabinet for removal

of filter cartridges. Allow enough space on

either side of the system for the tubing

connections.

1. Remove the prefilter and postfilter

cartridges.

2. Remove the assembly cover by unlocking

the four tabs on the cover from the system.

3. Use a flat-head screwdriver to work from

left to right from the underside of the

system.

4. Use the icons on the bottom of the

system for screwdriver positioning.

5. Hold the Reverse Osmosis assembly up to

the wall surface where you wish to install

it. Mark location for screws. There should

be a minimum of 17 inches from the

marks to the bottom of the cabinet floor.

CAUTION: Do not get dirt or

debris inside the assembly area. Use only to

mark mounting hole locations.

6. Install screws to the wall, leaving a 3/16-

inch clearance between the head of the

screw and wall (drill pilot holes if needed).

7. Hang the Reverse Osmosis assembly on

the screws. Tighten or loosen the screws

as desired until the system is secure on

the wall.

8. To install the

cover, line up

the front

tabs on the

cover with the

openings

in the system.

9. Snap the cover

in place; the

tabs will flex,

allowing the

cover to snap

in place.

10. Remove the

membrane

cartridge.

Screw locations

17 inches

7 inches

Screws

Screw

3/16″

Wall

Screwdriver positioning

ScrewdriverSystem opening

Tab

Prefilter

Postfilter

To removeTo remove

To remove

Membrane

8

Installation Instructions

FEED WATER SUPPLY

A. PREFERRED INSTALLATION

Utilizing existing kitchen sink water supply

valve (A) and removable faucet tubing (B).

1. Refer to illustration below to complete

assembly depending on supply valve

size (A).

2. Close the cold water supply valve (A)

under the sink.

3. Unscrew the flexible tubing line (B) from

the supply valve (A) that connects to the

COLD water riser.

NOTE: For rigid pipe, see C. Optional

Installation on page 10.

Note Adapter (C) orientation:

3/8-inch installation—Rounded end of adapter

(C) connects to supply valve (A).

1/2-inch installation—Rounded end of adapter

(C) connects to coupling (D), then to existing

faucet tubing (B).

Check and comply with local plumbing codes as you plan, then install a cold feed water supply fitting.

4. Assemble adapter (C) and coupling (D)

as shown in illustration at left, per your

configuration. Ensure that the gasket (G)

is in place before final assembly. Start

installation by hand, then finish tightening

with adjustable wrench. Be careful not

to overtighten or cross thread as damage

to threads may occur.

5. Hand tighten assembled adapter (C)

onto supply valve (A) for the proper size

installation. Be sure gasket (G) is in place

before final assembly. Start installation

by hand, then finish tightening with an

adjustable wrench. Be careful not to

overtighten or cross thread as damage

to threads may occur.

6. Reconnect faucet tubing line (B) to top

of adapter (C).

NOTE: If inlet valve (F) is to be removed

for installation, refer to E. Removal and

Reinstallation of Inlet Valve on page 11.

7. Cut wire ties on tubing coils, using care

not to damage tubes or parts if using a

utility knife.

8. Remove the 1/2″ nut (I) and ferrule (H)

from end of inlet valve. Using the yellow

banded tubing provided, place the nut (I)

and ferrule (H) onto the tubing and install

onto inlet valve (F) as shown at left.

Tighten with adjustable wrench. Be

careful not to overtighten or cross thread

as damage to threads may occur.

NOTE: Inspect the ends of the tubing prior

to installation to be sure there are no

imperfections and that the end of the tubing

is cut square. It may be necessary to cut

the tubing again.

9

For 3/8″ Plumbing For 1/2″ Plumbing

(B) Faucet

tubing line (not

included)

(D)

Coupling

(C)

Adapter

(F) Inlet valve

(A) Cold water

supply valve

(not included)

(B) Faucet

tubing line

(not included)

(A) Cold water

supply valve

(not included)

(D)

Coupling

(C)

Adapter

(G) Gasket

(G)

Gasket

(H)

Ferrule

(F) Inlet valve

(I) Nut

(G) Gasket

Installation Instructions

FEED WATER SUPPLY (cont.)

B. OPTIONAL HOME INSTALLATION

Where codes permit (Requires additional parts)

*For 1/2″ OD or larger metal tubing only.

NOTE: Codes in the state of Massachusetts

require installation by a licensed plumber and

do not permit the use of the saddle valve. For

installation, use plumbing code 248-CMR of the

Commonwealth of Massachusetts.

Saddle valve is available through GE Parts

and Services at 1.800.626.2002, part number

WS15X10023. Self piercing saddle valves are

not recommended.

1. Turn off the cold water supply and attach

saddle valve as required by product

selection. (Be sure to follow manufacturers’

Installation Instructions).

DANGER: Many homes are

electrically grounded through the plumbing.

To protect yourself from serious injury or

fatal shock, use a battery-powered hand drill

only to make the hole. DO NOT USE AN

ELECTRIC DRILL.

2. Close the water supply valve by turning

the handle clockwise.

3. Open the main water supply valve and

several house faucets to purge air from

the system. Close faucets when water

runs smoothly.

Snug valve into bracket

(DO NOT OVERTIGHTEN)

Some threads

should be visible

Rubber gasket

Optional water supply connection (using saddle valve)*

Pre-drill

1/4″ hole

Seal—make sure

the seal is in place

Clamp X

Nut (2)—not

required if holes

in clamp are

threaded

Valve

Handle

Tubing adapter

Washer

Compression

nut



Clamp Z

Use to connect the tubing

*For 1/2 ″ OD or larger metal tubing only.

C. OPTIONAL RIGID PIPE

INSTALLATION

For installation with rigid pipe between supply

valve and sink faucet.

Option 1

1. Remove pipe from supply valve and sink

faucet.

2. Obtain flexible pipe sized to your

plumbing.

3. Install flexible pipe.

4. GO back to A. Preferred Installation

section, step 4.

Option 2

1. Obtain compression fittings to fit rigid

pipe.

2. Obtain any other fittings required to

connect compression fittings to adapter.

NOTE: Adapter has 1/2-inch and 3/8-inch

internal and external threads.

3. Remove pipe from supply valve.

4. Cut pipe to fit length of assembled fittings

and adapter.

5. Install compression fitting to pipe.

6. GO back to A. Preferred Installation

section, step 4.

NOTE: Above described materials are not

included with the product.

10

Installation Instructions

D. OPTIONAL REMOTE LOCATION

INSTALLATION

(requires additional part)

1. Turn off the cold water supply.

2. Complying with plumbing codes, install a

fitting on the cold water pipe to adapt 1/4″

OD tubing. A typical connection is shown

in illustration below. Make sure a water

supply valve is used.

3. If the RO unit is to be installed more than

6 feet from the valve, replace the yellow

banded inlet tubing with a longer length

of GE 1/4″ tubing. A 33 foot length of 1/4″

tubing is available through GE Parts and

Services at 1.800.626.2002, part number

WS07X10018. DO NOT SUBSTITUTE

TUBING OF UNKNOWN QUALITY.

4. If the RO unit is to be installed more than

6 feet from the faucet, replace the blue

banded outlet tubing with a longer length

of GE 3/8″ tubing. A 33 foot length is

available through GE Parts and Services at

1.800.626.2002, part number WS07X10019.

See Faucet Installation on page 13 for more

details. DO NOT SUBSTITUTE TUBING OF

UNKNOWN QUALITY.

If you are using copper tubing, DO NOT

connect it directly onto the RO unit. Purchase a

connector and use a short length of the yellow

banded tubing provided to make final connection

to RO. Do not use copper tubing to attach to

icemaker or faucet.

Insert (not included)

Cold

water

pipe

1/4″ (yellow banded)

tubing to inlet

Ferrule

Water supply valve

To RO

Preferred water supply connection

(using compression fitting)

E. REMOVAL AND RE-INSTALLATION

OF INLET VALVE

(required only if

inlet valve needs to be removed to

complete Step 5 on page 13)

1. Remove inlet valve (F) from adapter (C)

using adjustable wrench on valve body.

See illustration below for detail. DO NOT

USE WRENCH ON HEX NUT END OF

VALVE AS LEAK MAY OCCUR.

2. Remove all sealing tape from inlet valve

(F) and adapter (C) threads.

3. Hand tighten assembled adapter (C)

onto supply valve (A) for the proper size

installation. Be sure the gaskets (G), as

shown on page 13, are in place before

final assembly. Finish tightening with

adjustable wrench. Be careful not to

overtighten or cross thread as damage

to threads may occur.

4. Using white thread sealing tape provided,

apply approximately 9 wraps of tape

around the large threads on inlet valve (F)

in a clockwise direction, as shown below.

5. Hand tighten inlet valve (F) into the adapter

(C), then finish tightening with adjustable

wrench. DO NOT USE WRENCH ON HEX

NUT END OF VALVE AS LEAK MAY OCCUR.

11

(C)

Adapter

(F) Inlet valve

Installation Instructions

INSTALLING THE TUBING TO TANK

AND FAUCET

1. Measure 3/4″ from the end of each

remaining piece of tubing (faucet end and

inlet end) and mark with a pencil. (Check

for roundness, smoothness, cuts, nicks,

flat spots and sharp edges).

2. Push the tubing firmly into each fitting on

the manifold until the line is flush with the

fitting collar. (If the tubing is removed, re-

cut the end, measure, mark and re-insert).

Tubing must be fully inserted to avoid

leaks. To remove tubing: depress and hold

red or blue collet; pull tubing out to remove.

3. Pull out slightly on tubing to ensure a

good seal.

3/4″

(19 mm)

INCORRECT

3

4

"

Engagement

3/4″

(3/8″ tubing)

Red or Blue Collet

(DO NOT REMOVE)

Insertion line

Insert tubing

FLOW RESTRICTOR

REPLACEMENT PROCEDURE

(cont.)

1. Remove drain line tubing by pushing up

on the drain line collet with one hand (1)

and removing the drain line with the

other hand (2).

2. Once the drain line has been removed

from the system base, grasp the end of

the flow restrictor and pull it straight out

from the tube*. If the restrictor is difficult

to remove by hand, a pair of pliers may

be used to grip the end of the restrictor

to aid in removal from the tubing.

*In some instances, the restrictor may slide out of the

drain tubing as it is removed from the drain line port.

If, after removing the drain line as described in step 1,

the restrictor is no longer in the end of the tubing,

check the drain line port. Remove the restrictor from

the port and proceed to step 3.

3. Take new restrictor and slide it back into the

drain tubing. Insert the restrictor by hand

only. Do not use pliers to insert. Make sure

to insert restrictor all the way into the

tubing. Failure to do so could result in

improper operation of the RO system.

4. Reinsert drain line tubing in system base.

Tug lightly on the tubing to ensure that

the collet is engaged and has a proper

grip on the tubing.

FEED WATER SUPPLY (cont.)

FLOW RESTRICTOR

REPLACEMENT PROCEDURE

Each time the Reverse Osmosis cartridge is

changed, you will need to replace the flow

restrictor in the drain line as well.

Be sure to wash your hands before handling

inner parts of the system.

12

1

2

Installation Instructions

FAUCET ASSEMBLY

FAUCET MOUNTING INSTALLATION

Be sure there is room underneath the sink to

make the needed connections. Select one of

the following locations to install the faucet:

• In an existing sink spray attachment or soap

dispenser hole.

• In a hole to be drilled in the sink top.

• In a hole to be drilled in the countertop,

next to the sink.

NOTE: Be sure the faucet base will fit flat

against the surface at the selected location

so the gasket will seal.

1. If drilling is needed, make a 1-1/4″ dia.

hole. Be sure to use the proper procedure

for drilling porcelain or stainless steel.

Special drill bits may be needed. Consult

a qualified plumber for proper procedure.

2. Remove the faucet, thin o-ring (D), faucet

base (E), bottom base gasket (F), lock

washer (G), hex nut (H) and mounting

bracket (I) from the packaging.

3. Feed the 3/8″ blue banded, 1/4″ black tube

(attached to the Reverse Osmosis System)

and the 3/8″ black tube (included in

separate packaging) up through the

mounting hole in the sink or countertop.

This step may require two people to

assemble. See page 14 for Optional

One Person Faucet Tubing Installation.

4. Feed the two black tubes up through the

gasket (F), faucet base (E) and O-ring (D).

NOTE: For ease of service and maintenance,

keep tubing lengths long enough so removal

of the Reverse Osmosis system from under

the sink is possible.

5. Push the 1/4″ black and 3/8″ black tubing

onto their respective fittings on the body (B).

NOTE: To ease insertion, submerge tubing ends

into hot water for a few minutes to soften.

6. Seat the base (E) and body (B) together.

Make sure the O-ring and gasket are

in place when the base meets the body.

The faucet handle will be at the 3 o’clock

position with respect to the base.

7. Slide the lock washer onto the threaded

stem of the body (B), then thread the hex

nut (H) onto the stem. Screw about halfway up.

NOTE: If installing faucet on a stainless steel

sink, slide on installation spacer (M) before the

lock washer.

8. Screw the blue tipped tubing adapter (K)

onto the threaded stem of the body (B).

9. Push the blue banded tubing into the

adapter. It should go in about 3/4″. Pull on

it to make sure it is installed correctly.

10. Feed the tubing and stem back down

through the 1-1/4″ hole.

11. Lower the faucet assembly into place

in the mounting hole and orient to final

position. Place the mounting bracket (I)

above the lock washer (G) around the

faucet stem. While holding the mounting

bracket in place, securely tighten the

hex nut. This step may require two people.

Mounting

bracket (I)

Base (E)

Hex nut (H)

Handle

Spout

Gasket (F)

Tubing adapter (K)

Lock washer (G)

O-ring (D)

Cap

ASSEMBLED

3/8″ barb

fitting

3/8″ (black)

drain tubing

1/4″ (black)

drain tubing

1/4″ barb fitting

Tubing adapter (K)

3/8″ (blue banded)

outlet tubing

Hex Nut (H)

Lock washer (G)

Installation spacer (M)

(as needed)

Body (B)

From ROFrom ROTo drain

13

Installation Instructions

FAUCET ASSEMBLY (cont.)

BATTERY INSTALLATION

1. Use a small flat blade screwdriver or coin

to remove the battery tray (A) at the side

of the faucet base.

2. Install one CR2032, 3 volt battery (B)

+ side down into the battery tray (A).

3. Slide tray into faucet base (C) until the

battery tray (A) edge is flush with the side

of the base.

4. The blue light (D) will flash 5 times,

indicating a proper installation and system

reset. If you want to reinitiate the start-up

sequence, remove the battery for 45–60

seconds; the electronics need to fully

discharge. Then put the battery back in.

5. The light is normally off. After 6 months

of use, the light will flash again every

30 seconds, indicating the proper time

to replace the filter cartridge.

NOTE: The blue light may stop blinking if

allowed to blink for an extended period of

time. To ensure proper operation, the battery

should be replaced with every filter change.

OPTIONAL ONE PERSON

FAUCET TUBING INSTALLATION

1. From under the sink, gather the 1/4″ drain

line (black), 3/8″ drain line (black) and 3/8″

outlet tube (blue banded) in one hand with

the drain tubes the same length and the

outlet tube offset approximately 6 inches.

2. Wrap a rubber band around all 3 tubes.

3. Insert a typical No. 2 pencil through the

rubber band location.

4. Rotate the pencil down until it is in line

with the tubing and push up through the

mounting hole. Release the grip on the

pencil and the tubes will remain in

position for easier faucet connection.

+

–

(B) Battery

(C) Faucet base

(A) Battery

tray

(D) Blue light

14

Installation Instructions

FILTRATION DRAIN CONNECTION

PREFERRED INSTALLATION:

OPTION A—BASEMENT ACCESS

INSTALLATION

Route the drain line DIRECTLY from the Reverse

Osmosis system to a standpipe in the basement,

bypassing the air gap provided in the faucet. The

air gap installation is left to the discretion of the

installer. The drain line may also be routed to a

floor drain or washtub, provided that the air gap

is maintained. Special air gap fittings are available

to connect the drain line to the top of the standpipe.

Check and comply with local plumbing codes as you plan.

CAUTION: The options detailed below are the ONLY approved installation

configurations. Do not use any drain saddle device.

NOTE: Failure to follow these Installation Instructions will void the warranty, and the installer will

be responsible for any service, repair or damages caused thereby.

15

Drain line from the Reverse Osmosis system

1″

1″ minimum air gap

must be maintained

PREFERRED INSTALLATION:

OPTION B—DRY-VENTED P-TRAP

INSTALLATION

Install a separate dry-vented p-trap under the

sink to be used exclusively for the Reserve

Osmosis drain line. A dry-vented p-trap is a

p-trap that has its own vent/stack. Attach the

drain line adapter to the p-trap and secure it

with the slip joint nut and washer as shown.

The drain line MUST be routed through the air

gap provided in the RO water faucet.

Reverse

Osmosis

drain line

Optional disposer

Installation Instructions

FILTRATION DRAIN CONNECTION (cont.)

PREFERRED INSTALLATION:

OPTION C—WET-VENTED P-TRAP

INSTALLATION

Install a p-trap under the sink to be used

exclusively for the Reverse Osmosis drain line.

A wet-vented p-trap is a p-trap that shares a

common vent/stack. Attach the drain line adapter

to the p-trap and secure it with the slip joint nut

and washer as shown. The drain line MUST be

routed through the air gap provided in the RO

water faucet. Locate the Reverse Osmosis p-trap

as high as possible (minimum of 4″ above

horizontal).

1″

SECONDARY INSTALLATION:

OPTION D—DRAIN LINE ADAPTER

INSTALLATION

CAUTION:

Using Option D

may result in clogging under adverse

conditions and requires periodic

inspection/cleaning by the user.

DO NOT INSTALL THE DRAIN LINE

DOWNSTREAM OF A DISPOSER OR IN A

HORIZONTAL PIPE. Install the drain line adapter

under the sink as shown (parts included). The

baffle tee shown must be installed to prevent a

clog in the Reverse Osmosis drain line. Route the

drain line from the air gap to the drain line

adapter, ensuring that there are no dips, loops or

low spots in the line. The drain line adapter

should be aligned vertically so that the hose

connection points upward (the hose connection

should never be allowed to drop below 45° from

this vertical position). This installation MAY result

in a slight drain noise in the sink drain when the

Reverse Osmosis system is regenerating. If this

happens, simply place the sink drain stoppers

in the strainer to suppress it.

Reverse

Osmosis

drain line

Optional disposer

Reverse

Osmosis

drain line

4″ minimum

Drain line

adapter

Maximum 45°

Baffle tee

(mandatory)

Optional

disposer

From

second sink

or disposer

45°

From faucet air gap

Drain line

adapter

Drain line connection should

be 180° opposite existing

horizontal pipe/baffle-tee as

shown in diagram

Drain line adapter

Proper drain line adapter orientation.

16

Installation Instructions

STORAGE TANK AND STARTUP

STORAGE TANK INSTALLATION

1. Remove the protective cap from the top

of the tank.

2. Apply 2–3 wraps

of thread tape,

in a clockwise

direction, to the

tank threads.

3. Install the push-to-connect fittings on the

threaded fitting on the tank as shown.

4. Push the 3/8″ red banded tubing from the

Reverse Osmosis System into the fitting

on the storage tank.

SYSTEM STARTUP PROCEDURE

CAUTION:

If installing the unit in

new construction, ensure that house plumbing

is flushed thoroughly before opening the water

supply valve.

1. Check that all tubing connections are

secure.

2. Turn on the Feed Water Supply Valve.

3. Check all connection points for leaks.

4. Follow the Sanitization procedures on

page 19.

5. After sanitization is complete, reinstall

prefilter, postfilter and Reverse Osmosis

cartridges.

6. Membrane contains a food grade

preservative. Allow the system to fill the

tank, then drain it completely four times

before using the water from the system.

7. Recheck all water connection points a few

days later to check for small leaks.

Storage

tank

Thread

tape

17

Troubleshooting TipsConsumer Support Troubleshooting Tips

Installation Instructions Safety InstructionsOperating Instructions

Care and cleaning of the reverse osmosis system.

Prefilter, Postfilter and Reverse Osmosis Membrane Cartridge Replacement Procedure

When the blue light in the faucet base flashes,

it is time to replace the prefilter and postfilter.

This will occur every 6 months.

Be sure to wash your hands before handling

inner parts of the system.

1. Turn OFF the icemaker (if attached to

the system).

2. Turn off water supply to the system.

3. Turn ON faucet to drain tank (may take several

minutes). Turn OFF faucet when tank is empty.

4. Remove the prefilter, postfilter and Reverse

Osmosis cartridge by rotating to the left about

1/3 turn.

5. Follow Sanitizing the Reverse Osmosis System

procedure found on page 19.

6. Remove foil on top of new replacement

cartridges. Install new cartridges into the

manifold by turning to the right about 1/3 turn

until the alignment marks line up and the

cartridges stop. DO NOT OVERTIGHTEN. The

cartridges will rise up as they are turned.

NOTE: The prefilter and postfilter are identical.

You may install either filter in the prefilter or

postfilter position. The reverse osmosis cartridge

is installed in the center position.

7. Turn ON water supply to fill the system

(may take up to four hours). Check for leaks.

8. Remove the battery tray and replace the

battery, positive “+” side down, to reset timer

and monitor function in faucet base (see Battery

Installation for proper procedure).

9. If only the prefilter and postfilter are replaced,

turn the faucet ON and empty the filled storage

tank. If the membrane cartridge is replaced, fill

and empty the storage tank a total of four times.

(This will remove the food grade preservatives

contained in new membranes. This preservative

will give product water an unpleasant taste

and odor.)

10. Once the storage tank is full, turn on the

icemaker.

NOTE: System should be sanitized when replacing

the prefilter and postfilter cartridge or the Reverse

Osmosis cartridge. Follow the Sanitizing the Reverse

Osmosis System procedure on page 19.

18

ON

OFF

To remove

Reverse

Osmosis

Prefilter Postfilter

ge.com

Sanitizing the Reverse Osmosis System

Sanitize upon installation of the Reverse Osmosis

system and after servicing inner parts, including

replacement of prefilter, postfilter and the

membrane cartridge.

Be sure to wash your hands before handling

inner parts of the system.

CAUTION: Before sanitizing, be sure to

remove all cartridges. Chlorine will destroy the

Reverse Osmosis membrane cartridge.

1. Follow steps 1 through 4 under Prefilter,

Postfilter and Reverse Osmosis Membrane Cartridge

Replacement Procedure.

2. Fill the empty canister labeled “Sanitization

Canister” with water to within 1 inch of the

upper opening. Add 1 oz. (2 Tbsp.) ordinary

household bleach. Install canister into the

prefilter canister position by turning to the right

about 1/3 turn until the alignment marks line

up and the canister stops.

3. Install the two additional “sanitiziation canisters”

into the membrane canister and postfilter

openings in the manifold by turning to the right

about 1/3 turn until the alignment marks line

up and the canister stops.

4. Turn ON water supply. Turn ON faucet until

water begins to flow from the faucet, then turn

faucet OFF. Allow system to fill for 10 minutes.

5. Turn faucet ON and allow water to flow for 20

minutes, or until bleach odor is gone. Turn OFF

water supply again. Turn ON faucet to drain

the system.

6. Once the system is drained, turn the faucet OFF

and remove the canisters by turning to the left

about 1/3 turn. Keep these in a safe place until

needed the next time.

19

Sanitization

canisters

Prefilter

position

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting TipsConsumer Support

Care and cleaning of the reverse osmosis system.

To obtain replacement filters, call toll-free GE Appliance Parts at 800.626.2002 (U.S.),

800.663.6060 (Canada–English), 800.361.3869 (Canada–French), or visit the store where

you purchased your reverse osmosis system.

CAUTION: Before servicing the Reverse Osmosis system, close the water supply/saddle valve

and open the RO water faucet. Allow the system to drain.

Prefilter/Postfilter Cartridge Replacement FQROPF Carbon Block

Reverse Osmosis Cartridge Replacement FQROMF Thin Film Polyamide

The Water Test Kit

To obtain an independent laboratory water test kit, please call Legend Technical Services at

1.800.826.8553 ext. 47 and leave your contact details. They will contact you to find out what water

tests you are interested in, and inform you of the cost of the testing. You will then receive a kit that

will include all necessary tests to properly indicate the performance level of your system. Product

water should be tested a minimum of every six months.

NOTE: When the TDS reduction of the system falls below 75%, it is time to replace the reverse

osmosis cartridge in addition to the prefilter and postfilter.

20

La page charge ...

GE Profile PXRQ15F Manuel utilisateur

Ce manuel convient également à

GE Profile PXRQ15F Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents