Crosley CDBEH600SB2A Le manuel du propriétaire

Marque: Crosley

Modèle: CDBEH600SB2A

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

TABLE OF CONTENTS

All about the

Use & Care

of your Dishwasher

Crosley

www.crosley.com USA and Canada 1-336-761-1212

Important Safety Instructions ......................2

Product Registration ...................................3

Features at a Glance ...................................4

Operating Instructions .............................5-6

Preparing and Loading Dishes ..................7-9

Dishwasher Dispenser and Detergents .......10

Factors Affecting Performance ...................11

Care and Cleaning ............................... 12-13

Before you Call .................................... 13-15

Major Appliance Warranty .........................16

P/N A05763001RevA Artwork A05763001Rev001 (July 2016)

WARNING

This symbols will help alert you to such

dangers as personal injury, burns, ﬁ re and

electrical shock..

WARNING

To reduce the risk of ﬁ re, electrical shock or

injury when using your dishwasher, follow

the above basic precautions ..

IMPORTANT SAFETY INSTRUCTIONS

For your Safety

• Use your dishwasher only as instructed in

this Use and Care Manual.

• This Manual does not cover every possible

condition and situation that may occur.

Use common sense and caution when

installing, operating and maintaining any

appliance.

• NSF certiﬁ ed residential dishwashers

are not intended for licensed food

establishments.

• DISHWASHER MUST BE ELECTRICALLY

GROUNDED. Read the Installation

Instructions for details.

WARNING

Please read all instructions before using this

dishwasher.

• This dishwasher is designed to operate on

regular house current (120V, 60Hz). Use

a circuit equipped with a 15 ampere fuse

or circuit breaker. Use a 20 ampere fuse

if dishwasher is connected with a food

disposer.

• Do not operate dishwasher unless all

enclosure panels are in their proper place.

• To avoid entrapment and/or suffocation,

remove door or door latch mechanism from

any dishwasher that is discarded or not in

use.

• Keep young children and infants away from

dishwasher when it is operating.

• Do not let children abuse, sit, stand or play

on door or racks of a dishwasher.

• Use only detergents and rinse agents

recommended for use in a dishwasher.

• Store dishwasher detergent and rinse

agents out of the reach of children.

• Do not wash plastic items unless marked:

“Dishwasher Safe” or equivalent. Check

with manufacturer for recommendations,

if not marked. Items that are not marked

dishwasher safe may melt and create a

potential ﬁ re hazard.

• Disconnect electrical power to dishwasher

before servicing.

• If the dishwasher drains into a food

disposer, make sure disposer is completely

empty before running dishwasher.

• Repairs should be done by a qualiﬁ ed

technician.

• Do not tamper with controls.

• Do not touch the heating element during or

immediately after wash has completed.

• Use care unloading the dishwasher when

the SANITIZE option has been selected.

Contents may be hot to the touch

immediately after the end of cycle.

• Water vapor from the vent may be hot to

the touch when the SANITIZE option has

been selected. Use care and do not let

small children play around or touch the

vent area of the dishwasher.

• When loading items to be washed:

• Locate sharp items and knives so that

they are not likely to damage the door

seal or tub.

• Load sharp items and knives with the

handles up to reduce the risk of cut-type

injuries.

• Under certain conditions, hydrogen gas

may be produced in a hot water, system

that has not been used for 2 weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If

hot water system has not been used for

such a period, before using dishwasher,

turn on for several minutes This will

release any accumulated hydrogen gas.

HYDROGEN GAS IS FLAMMABLE. Do not

smoke or use an open ﬂ ame during this

time.

• Do not store or use combustible materials,

gasoline or other ﬂ ammable vapors and

liquids in the vicinity of this or any other

appliance.

PRODUCT REGISTRATION

NOTE

Thank you for choosing Frigidaire

This Use & Care Guide is part of our

commitment to customer satisfaction and

product quality throughout the service life of

your new appliance.

We view your purchase as the beginning of a

relationship. To ensure our ability to continue

serving you, please use this page to record

important product information.

_________________________________

Purchase Date

_________________________________

Model Number

_________________________________

Serial Number

Registering your product with Frigidaire

enhances our ability to serve you. You can

dropping your Product Registration Card in the

mail.

Very Important Information

- Read Before Operating Your

Dishwasher!

Normal Operating Sounds

This dishwasher does not sound like most

dishwashers - IT’S QUIETER.

Your Precision Direct Wash System dishwasher

uses energy efﬁ cient motors for the wash and

drain portions of the cycle you select. Each cycle

has a series of water ﬁ lls and drains for washing

and rinsing dishes. As each cycle begins, you

may - or may not - hear the drain motor.

The next sound you will hear is the splashing

water as it enters the tub. Then the lower arm

rotates and circulates water. This is followed

by a pause and a slightly different sound as the

upper arms spray water. If you listen closely, you

will hear the change in sound as the wash action

switches from one arm to the other.

PLEASE BE ADVISED: If you

compare this dishwasher to

previous models, you may be

surprised at what you DON’T hear.

FEATURES AT A GLANCE

Features may vary according to model

Heating Element

Glass Trap

Detergent Dispenser

Overﬁ ll Protector

Silverware Basket

Lower Rack

Serial Label

(Located on Right)

Top Rack

Nozzle or Spray Arm

Cup Shelves

Middle Spray Arm

Lower Spray Arm

Rinse Aid

Vent

Your dishwasher cleans by spraying a mixture of hot water and detergent through the spray arms

against soiled surfaces. First, the dishwasher ﬁ lls with water covering the ﬁ lter area. Water is

then pumped through the spray arms. Soil particles go through and across the ﬁ lter and down the

drain as the water is pumped out. This series of steps are repeated as needed. The number of

water ﬁ lls vary with the cycle being used.

NOTE

Not all cycles and options available on all

models.

NOTE

The dishwasher is programmed to remember

your last cycle so you do not have to reset

each time. To start the dishwasher using

the same cycle and options selected on the

previous wash, just press the START/CANCEL

pad.

Getting Started

1. Load Dishwasher (See Preparing and

Loading Dishes).

2. Add detergent (See Dishwasher

Dispenser & Detergents).

3. Add Rinse Aid, if needed (See Rinse

Aid).

4. Close door to latch.

5. Select desired CYCLE (See Cycle

Chart). The indicator light above the pad

will glow when selected.

6. Select desired OPTION (See Energy

Options). The indicator light above the pad

will glow when selected.

7. Run hot water faucet nearest

dishwasher until water is hot. Turn water off.

8. To start, press START/CANCEL pad.

Wash Cycle Selections

Cycle times are approximate and will vary with

options selected. Hot water is necessary to

activate dishwasher detergent and melt fatty

food soils. An automatic sensor will check

the incoming water temperature and, if it is

not hot enough, the cycle will be lengthened

for automatic water heating in the main wash

and ﬁ nal rinse of all cycles. This happens

even when HI-TEMP WASH option has not be

selected. When HI-TEMP WASH is selected,

an even higher temperature will be reached to

handle heavier soil loads.

OPERATING INSTRUCTIONS

Option Selections (*available on

select Models)

*Sanitize Option

To sanitize your dishes and glassware, select

SANITIZE option. When selected, the light

above the pad will come on and remain on until

end of cycle. The water temperature in the

ﬁ nal rinse will be raised to 155

F (68

C) and will

maintain that temperature for 9 minutes. This

option is available in Heavy and Normal Cycles.

Only these sanitization cycles have been

designed to meet NSF requirements.

The cycle time will be extended until the proper

water temperature is reached.

Washing

action will continue during the water heating

delay. For best results, the incoming water

temperature should be at least 120

F (49

C).

The sanitize criteria may not be satisﬁ ed if there

is an interruption of the cycle, power failure or if

the incoming water temperature is below 120

(49

C).

To turn off the SANITIZE option, press the pad

a second time. The light above the pad will

turn off.

*Hi-Temp Wash Option

When HI-TEMP WASH option is selected, the

dishwasher heats water in the main wash to

approximately 140

F (60

C).

This increase in water temperature helps the

dishwasher detergent remove food grease and

soil from dishes more effectively and aids in

improved drying performance. HI-TEMP WASH

option can be used with all cycles except RINSE

ONLY. HI-TEMP WASH is automatically provided

when the HEAVY WASH cycle is selected.

When HI-TEMP WASH option is selected, the

light above the pad will come on and remain

on until end of cycle. To turn off the HI-TEMP

WASH option, press the pad a second time.

The light above the pad will turn off.

Heat Dry

The HEAT DRY option in combination with

rinse aid will enhance drying performance.

The energy required to use the HEAT DRY

option costs pennies per cycle; however you

will have items in your dish load that will not

be completely dry at the end of the cycle.

Child Lock Controls

To prevent children from accidently changing

the dishwasher cycle or starting the

dishwasher, lock the dishwasher controls by

pressing and releasing the DRY OPTION pad

for 3 seconds while the door is latched. An

indicator light on the lock graphic pad will

illuminate when the controls are locked and

no new selections can be made until the lock

is released. To unlock the controls, press the

same pad, DRY OPTION, again for 3 seconds

until the indicator light goes out.

*Status Indicator Lights

The WASHING light comes on at the beginning

of the cycle and remains on until the end of

the main wash.

Whether heated or unheated dry is selected

the DRYING light will come on during the

drying portion of the cycle.

When the SANITIZE option is selected, the

SANITIZED light will glow when the SANITIZE

cycle is ﬁ nished. If the dishwasher did not

properly sanitize the dishes, the light will not

come on. This can happen if the cycle is

interrupted. The light will remain on until the

door is opened.

The CLEAN light will come on at the end of

cycle and remain on until the door is opened.

*Delay Start

The DELAY START option allows you to

automatically delay starting your dishwasher

for either 2-4-6 hours.

To activate delay start option for 2-4-6 hour

delay, press the pad once for a 2 hour delay,

twice for 4 hours and three times for 6 hours.

A light will come on indicating the delay start

hours and will remain on until cycle starts.

Press the START/CANCEL pad to start the delay

option. If the delay option is interrupted, the

START/CANCEL pad will have to be pressed

again to return to delay option.

To cancel the DELAY START option and begin

the cycle before the delay period is over,

press and hold the START/CANCEL pad for 3

seconds.

To Cancel a Cycle

You can cancel a cycle anytime during the cycle.

Press and hold the START/CANCEL pad for 3

seconds. The light above the cycle and option

selected will go out, the START/CANCEL light

will remain illuminated, the dishwasher will start

a 90 second drain. At the end of the drain,

select the next desired cycle.

NOTE

If the dishwasher door is opened while the

unit is running, the START/CANCEL pad must

be pressed and the door shut immediately

to return the unit to the selected cycle and

option, this must happen within 10 minutes

for the unit to continue the cycle.

OPERATING INSTRUCTIONS

Cycle and intended use Water per

Cycle

Heavy Wash

Recommended for pots, pans,

casseroles and dinnerware

having light to heavily soiled

loads.

9 gal.

34 L.

- 2

Hours

Duration*

(approx.)

Normal Wash

Recommended for lightly to

heavily soiled loads.

Light Wash

Recommended for lightly

soiled loads only.

Energy Saver

A cycle used to reduce

dishwasher energy

consumption.

Available Options

Temperature;

Drying

Sanitize, Hi-Temp

Heat Dry, Air Dry

Rinse Only

For rinsing dishware that will be

washed later.

Sanitize, Hi-Temp,

Normal;

Heat Dry, Air Dry

2.9 - 7.6 gal.

11 - 29 L.

- 2

Hours

Hi-Temp, Normal

Heat Dry, Air Dry

Normal

Heat Dry, Air Dry

N/A

Cycle and Option Chart

(approx.)

Model CDBEH600

5 gal.

19 L.

Hours

16 Mins.

(Air Dry Only)

Hours

5 gal.

19 L.

2 gal.

8 L.

*Does not include drying time.

PREPARING AND LOADING DISHES

Dish Preparation

Scrape away large pieces of food, bones, pits,

toothpicks, etc. The continuously ﬁ ltered wash

ﬂ uid will remove remaining food particles.

Burned-on foods should be loosened before

loading. Empty liquids from glasses and cups.

Foods such as mustard, mayonnaise, vinegar,

lemon juice and tomato based products may

cause discoloration of stainless steel and

plastics if allowed to sit for a long period of

time. Unless the dishwasher is to be operated

at once, it is best to pre-rinse or use the rinse

only cycle to rinse off these food soils.

• Load racks so that large items do not

prevent the detergent dispenser from

opening.

• Check manufacturer’s recommendations

before washing items in question.

• If the dishwasher drains into a Food

Disposer, be sure disposer is

completely empty before starting

dishwasher.

Loading the Top Rack

Features and appearance of racks and

silverware basket may vary from your

model.

The upper rack is designed for ﬂ exibility in

loading a wide variety of items including cups,

glasses, stemware, small plates, bowls, etc.

Load glasses in top rack only. Damage may

occur if placed in bottom rack.

Load plastic items in top rack only. Melting

may occur if placed in bottom rack.

Load items with open ends facing down for

better cleaning and draining.

Damage may occur if delicate items touch

each other during dishwasher operation.

Long-handled knives and utensils can be

placed in top rack.

Be sure nothing protrudes through the bottom

of the rack to block rotation of middle spray

arm.

10 place settings standard loading pattern

12 place settings standard loading pattern

Some models have a fold-down cup shelf

or a cup shelf/stemware holder. They can

be used to load two levels of cups, juice

glasses, and other short items. Stagger

items on upper level so that water can

reach all inside surfaces. Fold up to load

tall glasses.

PREPARING AND LOADING DISHES

Top Rack

The TOP RACK option can be used to wash

a wide assortment of items when you don’t

have a full load. Also, when the upper rack

ﬁ lls up with glasses and the lower rack is still

empty, you don’t have to wait anymore for

clean glasses.

STEMWARE HOLDER/CUPSHELF not

available on all models.

Features and appearance of racks and

silverware basket may vary from your

model.

The lower rack is best for plates, saucers,

bowls, and cookware. Large items should be

placed along the edge so they do not block

the spray arm rotation. For best results, place

bowls, casseroles, and sauce pans with soiled

surface facing down or toward the center. Tilt

slightly for better drainage.

Make sure tall items do not block spray arm

rotation.

Be sure pan handles do not protrude through

the bottom of the rack and block the spray

arm rotation.

Loading the Bottom Rack

10 place settings standard loading pattern.

12 place settings standard loading pattern.

PREPARING AND LOADING DISHES

CAUTION

Load sharp items (knives, skewers, etc.)

pointing down.

Failure to do so may result in injury.

Features and appearance of racks and

silverware basket may vary from your

model.

Load the silverware basket while it is in the

bottom rack or take the basket out for loading

on a counter or table.

Use suggested loading patterns, as shown, to

increase washability of the silverware.

Be sure nothing protrudes through bottom of

basket or rack to block the spray arm.

Do not mix silver and stainless to avoid

damaging the silver ﬁ nish.

When covers are up, mix items in each

section of the basket with some pointing

up and some down to avoid nesting. Water

spray cannot reach nested items.

Adding a Dish

To add or remove items after wash cycle

starts:

• Unlatch door and wait a few seconds

until wash action stops before opening.

• Add the item and wait a few seconds to

allow cold air to slowly expand inside

dishwasher.

• Close door ﬁ rmly to latch and press the

START/CANCEL pad to resume.

Loading the Silverware Basket

CAUTION

The use of industrial grade detergent can

damage the heating coil and other parts of

the dishwasher leading to damage to the

unit and surrounding property. Use only

household grade automatic dishwasher

detergents.

If the cover is closed on the Main Wash

Cup open by pressing the Cover Latch.

How much Detergent to use

The amount of detergent to use depends

on the water hardness. Water hardness is

measured in grains per gallon. Using too little

detergent can result in poor cleaning and hard

water ﬁ lming or spotting. Using too much

detergent in soft water can cause etching

to some glassware which is surface damage

that appears like a ﬁ lm but cannot be wiped

off. Your local water company, water softener

company or county extension agent can tell

you the water hardness in your area.

Detergent Usage Chart

Cycle

Soft Water

(0-3 grains)

Medium Hard Water

(4-8 grains)

Hard Water

(9-12 grains)

Very Hard Water

(Over 12 grains)

Heavy Wash

Normal Wash

Top Rack

Rinse Only

2 teaspoons

(each cup-

1/4 full)

2 teaspoons

(Main Wash

cup-

1/4 full)

No Detergent No Detergent No Detergent No Detergent

(water softener

recommended)

5 teaspoons

(each cup- ﬁ ll

to line above

“Regular”)

5 teaspoons

(each cup- ﬁ ll

to line above

“Regular”)

8 teaspoons

(each cup-

completely full)

8 teaspoons

(Main Wash

cup- completely

full)

Each Cup-

Completely

Full (water

softener

recommended)

Main

Wash Cup-

Completely Full

(water softener

recommended)

DISHWASHER DISPENSER & DETERGENTS

The detergent dispenser has two detergent

cups. The smaller one is for addition to the

pre-wash and the larger is for release to the

main wash.

• Use only fresh automatic dishwashing

detergent. Other detergents may cause

oversudsing.

• When using automatic dishwashing

detergent tabs, place one tab in main

wash cup and close.

• Add detergent just before starting cycle.

• Store detergent in a cool, dry location.

Moist or caked detergent may not dissolve

properly.

Filing the Detergent Dispenser

As a rule, use 1 teaspoon for each grain above 12. For very hard water, detergent alone

may not be enough and then a water softener is recommended to improve water quality and

dishwashing performance.

Cover

Main Wash

Cup

Cover

Latch

Pre-Wash

Cup

IMPORTANT

Before starting a cycle, run hot water

to clear cool water from pipe.

FACTORS AFFECTING PERFORMANCE

Rinse Aid

Rinse aid greatly improves drying,

reduces water spots, ﬁ lming, and

lubricates wash arm bearing for proper

rotation. With it water “sheets” off dishes

rather than forming water droplets that cling

and leave spots.

A dispenser, located next to the detergent cup,

automatically releases a measured amount of

rinse aid during the last rinse. If spotting and

poor drying are problems, increase the amount

of rinse aid dispensed by rotating the dial to a

higher number. The dial is located under the

dispenser cap. The indicator will be dark when

full and will show clear when it is time to reﬁ ll.

To add liquid rinse aid, turn dispense cap 1/4

turn counterclockwise and lift out. Pour in

rinse aid until liquid touches the indicated ﬁ ll

level Replace cap.

Do not overﬁ ll since this can cause

oversudsing. Wipe up any spills with a damp

cloth.

The dispenser holds enough for 35 to 140

washes, depending on setting.

Water Pressure

The hot water line to dishwasher must provide

water pressure between 20 and 120 psi.

Low Water pressure may occur when laundry

or showers are in operation. If you experience

poor wash performance you may need to

wait until water use is reduced before starting

dishwasher.

Water Temperature

Hot water is needed for best dishwashing and

drying results. Water entering dishwasher

should be at least 120

F (49

C) to give

satisfactory results.

To check water temperature entering

dishwasher:

• Turn on hot water faucet nearest

dishwasher for several minutes to clear

cool water from pipes.

• Hold a candy or meat thermometer in the

water stream to check the temperature.

• If temperature is below 120

F (49

C),

have a qualiﬁ ed person raise the hot

water heater thermostat setting.

The HEAT DRY option in combination

with rinse aid will enhance drying

performance. The energy required to use

the HEAT DRY option costs pennies per

cycle. You may choose not to select the

HEAT DRY option; however you will have

items in your dish load that will not be

completely dry at the end of the cycle.

Dispenser Opening Indicator

Dispenser Cap

Adjustable Setting

NOTE

To achieve the best results from your

dishwasher, visit www.dishwashingexpert.com

for general tips regarding the performance

and operation of your dishwasher.

To empty the glass trap:

1. Grasp the glass trap’s handle and rotate it

clockwise while pressing down on the

center of the wash arm.

2. Grab the spray arm in the center and lift

the spray arm and glass trap assembly up

and out form the dishwasher.

3. Tip the assembly over an appropriate

container and tap it to empty the glass

trap.

OR, separate the glass trap - pull

the glass trap handle toward you, then

up, then further toward you to slide it

away from the rest of the assembly;

empty it into an appropriate container;

then slide the glass trap back into the

assembly.

4. Place the assembly back into position,

press down on the arm at the center

and rotate the glass trap handle 90

counterclockwise being sure the glass

trap ends in the orientation shown in the

image above. To avoid damage to

your unit make sure the spray arm

and glass trap are fully snapped in

place.

Spray Arm varies

by model

Glass Trap

Glass Trap Removal

(1)

(2)

(3)

Outer Door - Clean outer door with warm

soapy water and a dishcloth or sponge. Rinse

with clean water and a dry cloth. Do not use

harsh cleaners.

Inside - The inside of the dishwasher and

ﬁ lter are self-cleaning with normal use. If

needed, clean around the tub gasket area with

a damp cloth. The ﬁ lter is self-cleaning. A

glass trap located in the center of the ﬁ lter

is designed to collect pieces of broken glass,

straws, bones and pits.

NOTE

Hard water may cause lime deposit buildup

on the interior of the dishwasher. For

cleaning instructions see “Removing Spots

and ﬁ lm” section.

Overﬁ ll Protector- keeps dishwasher

from overﬁ lling and is located in the left front

corner of the tub.

• Clean occasionally with household cleaner

containing vinegar or bleach to dissolve

any buildup.

• Overﬁ ll Protector should move up and

down freely about one inch. If it does not

move, lift and clean underneath.

WARNING

Burn Hazard

Allow heating element to cool before

cleaning the interior.

Failure to do so can result in burns.

CARE AND CLEANING

Care of Drain Air Gap

If a drain air gap was installed for your built-in

dishwasher, check to make sure it is clean so

the dishwasher will drain properly. A drain air

gap is usually mounted on countertop and can

be inspected by removing the cover. This is

not part of your dishwasher and is not covered

by warranty.

CARE AND CLEANING

Winterizing

A dishwasher left in an unheated place should

be protected from freezing. Have a qualiﬁ ed

person do the following:

To Disconnect Service:

1. Turn off electrical power to the

dishwasher at the supply source by

removing fuses or tripping circuit breaker.

2. Shut off water supply

3. Place a pan under the inlet valve.

Disconnect water line from inlet valve

and drain into pan.

4. Disconnect drain line from pump and

drain water into pan.

To Restore Service:

5. Reconnect the water, drain, and electrical

power supply.

6. Turn on water and electrical power

supply

7. Fill both detergent cups and run

dishwasher through a HEAVY WASH/

cycle.

8. Check connections to make sure they do

not leak.

NOTE

See Installation Instructions for more details

on disconnecting and restoring service to

your dishwasher.

Before calling for service, review this

list. It may save you both time and

expense. This list includes common

experiences that are not the result of

defective workmanship or material in

your dishwasher.

Food Soils Left on Dishes

• Choose another cycle for longer washing

time.

• Check rack loading section for proper

loading-avoid nesting items.

• Do not overload the dishwasher (See

Preparing and Loading Dishes).

• Check to verify that the glass trap is

maintained and installed properly (See

Care and Cleaning)..

• Home water pressure may be too low-

should be 20 to 120 pounds per square

inch (psi).

• Check incoming water temperature. It

should be about 120

F (49

C). (See

Factors Affection Performance.)

• Check water hardness. For extremely

hard water, it may be necessary to install

a water softener. (See Detergent Chart).

• Use Fresh Detergent.

• Make sure items are not blocking the

spray arms, preventing them from

rotating.

Dishes not Dry

• By selecting Heat Dry, Hi-Temp Wash or

Sanitize options this will improve drying.

• Make sure the rinse aid dispenser is

ﬁ lled.

• Increase the discharge setting of rinse

aid. (See Rinse Aid).

• Check the incoming water temperature.

Be sure it is at least 120

F (49

C).

• Check for proper loading-avoid nesting

items.

• Plastic items may need to be towel dried.

• Cups with a concave bottom will collect

water. Load them at the far left of the

upper rack so they will be held in a tilted

position.

• Containers, bowls, pots/pans, and any

dishware with concave surfaces that can

collect water should be placed in the

rack facing or angled down so that water

is able to drain even from the lowest

point.

Glassware/Flatware Spotted or Cloudy

• Check water hardness. For extremely

hard water, it may be necessary to install

a water softener. (See Detergent Chart).

• Water temperature may be low. Avoid

extremely low or high temperatures.

(See Factors Affecting Performance.

• Avoid overloading and improper loading.

(See Preparing and Loading Dishes).

• Use fresh detergent. Old detergent is

ineffective.

• Make sure rinse aid dispenser is ﬁ lled.

• Check to see that proper amount

of detergent is being used for cycle

selected. (See Detergent Dispenser).

• Home water pressure may be too low-it

should be 20 to 120 pounds per square

inch (psi).

Before You Call

BEFORE YOU CALL

Dishware Chipped

• Load with care and do not overload. (See

Preparing and Loading Dishes).

• Place delicate items in top rack.

• Place glasses securely against pins and

not over pins.

• Load items so they are secure and don’t

jar loose when moving racks in and out.

Move racks in and out slowly.

• Make sure tall glasses and stemware will

clear top of tub when rack is pushed in.

• Fine antique china and crystal should be

hand-washed.

Dishware Stained or Discolored

• Tea and coffee can stain cups. Remove

the stains by hand washing in a solution

of 1/2 cup (120 ml) bleach and one quart

(1L) of warm water. Rinse thoroughly.

• Iron deposits in water can cause a yellow

or brown ﬁ lm. A special ﬁ lter installed

in the water supply line will correct this

problem. (See Removing Spots and Film).

• Aluminum utensils can leave gray/black

marks when they rub against other items.

Load Properly.

• Certain high acid foods can cause

discoloration of stainless steel and plastics

if allowed to sit for a long period. Use the

Rinse Only cycle or rinse by hand if not

operating dishwasher at once.

• Mixing stainless steel and silver utensils

in silverware basket can cause pitting of

the stainless steel blades. Avoid mixing

stainless steel and silver.

Etching

• Using too much detergent especially in

soft or softened water causes damage

that looks like a ﬁ lm but cannot be

removed.

• Adjust the amount of detergent based

on the water hardness. (Check Detergent

Chart).

• Lower the water temperature by selecting

the Normal Cycle.

Detergent Left in Cups

• Detergent may be old. Discard and use

fresh detergent.

• Be sure the dish load doesn’t spray from

entering the detergent cup.

• Check to see if cycle has been completed.

• Make sure items do not prevent the

detergent dispenser from opening.

Vapor at Vent

• Water vapor escapes from the vent during

the drying part of cycle. This is normal.

• Spilled rinse aid can cause foam and lead

to overﬂ owing. Wipe up any spills with a

damp cloth.

• Check to see that dishwasher is level.

(See Installation Instructions).

Normal Sounds You Will Hear

• Normal sounds include water ﬁ ll, water

circulation and motor sounds.

• There is a noticeable change in sound

when the wash action switches between

the lower and middle spray arm. This is

normal since each spray arm has it’s own

sound.

• It is normal for the dishwasher to pause

(no sound) when the wash action is

switching between the lower and middle

spray arms.

Water in Bottom of Tub

• Water left in the tub bottom after the

cycle is complete is not normal. If

water remains in the bottom of the tub,

the dishwasher may not be draining

properly. (See Dishwasher Does not Drain

Properly).

Dishwasher Leaks

• Check that the door gasket is pressed

into its mounting channel, reaches to the

bottom of the tub and does not extend

beyond the end rib so as to interfere with

door closure.

• Spilled rinse aide can cause foam and

lead to overﬂ owing. Wipe up any spills

with a damp cloth.

• Check to see that the dishwasher is level.

(See Installation Instructions).

• Avoid oversudsing by using the correct

amount of detergent designed for

automatic dishwashers.

• Check to see that dishwasher is level.

(See Installation Instructions).

Dishwasher Won’t Fill

• Assure the water supply is turned on.

• Check that the overﬁ ll protector moves up

and down freely. (See Overﬁ ll Protector

section).

BEFORE YOU CALL

Dishwasher Does Not Drain Properly

• If unit is hooked up to a food waste

disposer, make sure the disposer is empty.

• Assure the knockout plug has been

removed from inside the food waste

disposer inlet.

• Assure the drain hose isn’t kinked.

• Make sure cycle is complete, not in a

pause.

• Assure the glass trap is maintained and

installed properly assuring no clogs (See

Care and Cleaning).

Cycle Takes a Long Time

• The cycle may have been automatically

lengthened to reach key temperatures

due to some factor such as a cool water

supply or a large load of dishes.

• Delay Start option may have been

selected.

• Choose lower temperature options to

shorten the cycle.

• Cycles that are soil-sensing adjust

automatically to assure a good wash

- heavier soils will elicit a longer cycle

response.

Dishwasher has an Odor

• Soiled dishes left in dishwasher too long

can create an odor. Use Rinse Only cycle.

• There will be a “new” smell when ﬁ rst

installed. This is normal.

• Check to see if unit is draining properly.

(See Dishwasher Does Not Drain

Properly).

Dishwasher Won’t Run

• Check to see if circuit breaker is tripped

or if a fuse is blown.

• Make sure water supply is turned on.

• Check to see if cycle is set correctly. (See

Operating Instructions).

• Is dishwasher set for Delay Start Option?

• Make sure door is closed and latched.

• Make sure START/CANCEL pad is pressed

after the cycle has been selected.

Removing Spots and Film

Hard water can cause lime deposit buildup

on the interior of the dishwasher. Dishes

and glasses may also get spots and ﬁ lm for a

number of reasons. (See Glassware/Flatware

Spotted or Cloudy section). To remove

buildup, and ﬁ lm, clean using the following

instructions:

1. Load clean dishes and glasses in normal

manner. Do not load any metal utensils

or silverware.

2. Do not add detergent.

3. Select the NORMAL WASH cycle. Close

and latch door. Press START/CANCEL

pad.

4. Allow dishwasher to run until it starts

the second water ﬁ ll (approximately 10

minutes).

5. Unlatch and open door and pour 2 cups

of white vinegar into the bottom of

dishwasher.

6. Close and latch door and allow cycle to

ﬁ nish.

Stains on Tub Interior

• Washing large amounts of dishware with

tomato based soil can cause a pink/

orange appearance. This will not affect

performance and will gradually fade over

time. Pre-rinsing or using the Rinse Only

cycle will reduce the chance of staining.

Using no heat dry option will lessen

staining.

Opening the door during cycle

• If the dishwasher door is opened while

the unit is running, the START/CANCEL

pad must be pressed and the door shut

immediately to return the unit to the

selected cycle and option, this must

happen within 10 minutes for the unit to

continue the cycle.

MAJOR APPLIANCE WARRANTY

Your appliance is covered by a one year limited warranty. For one year from your original date of

purchase, Crosley will pay all costs for repairing or replacing any parts of this appliance that prove to

be defective in materials or workmanship when such appliance is installed, used and maintained in

accordance with the provided instructions.

Exclusions

If You Need Service

This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside

the USA or Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased “as-is” are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances

not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,

shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air ﬁ lters, water ﬁ lters, other

consumables, or knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry

trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the ﬁ nish of appliance or home incurred during installation, including but not

limited to ﬂ oors, cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than

genuine Crosley parts or parts obtained from persons other than authorized service companies; or

external causes such as abuse, misuse, inadequate power supply, accidents, ﬁ res, or acts of God.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT

REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,

INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE

LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE

YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH

AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS

WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO

NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,

OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR

EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL

RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by

Crosley Corporation. In Canada, your appliance is warranted by Crosley Canada Corp. Crosley

Corporation authorizes no person to change or add to any obligations under this warranty.

Obligations for service and parts under this warranty must be performed by Crosley Corporation

or an authorized service company. Product features or speciﬁ cations as described or illustrated are

subject to change without notice.

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty

period should service be required. If service is performed, it is in your best interest to obtain

and keep all receipts. Service under this warranty must be obtained by contacting Crosley at the

addresses or phone numbers below.

FOR WARRANTY INFORMATION CONTACT:

USA 1.800.944.9044

Canada 1.866.213-9397

FOR PRODUCT INFORMATION CONTACT:

336.761.1212

Crosley Corporation

111 Cloverleaf Drive, Suite 200

Winston-Salem, NC 27103

CROSLEY

www.Crosley.com

TABLE OF CONTENTS

Crosley

www.crosley.com USA and Canada 1-336-761-1212

Mesures de sécurité importantes ...............18

Enregistrement de Produit ........................19

Caractéristiques de Lave-Vaisselle ..............20

Fonctionnement de L’appareil ...............20-22

Préparation et Chargement

de La Vasisselle ...................................23-25

Tout à propos de

l'utilisation

et l'entretien

de votre Dishwasher

Distributeur et Détergents .........................26

Facteurs qui Affecte le Rendment ..............27

Entretien et nettoyage ......................... 28-29

Solutions aux Problémes Usuels ...........29-31

Garantie .................................................32

AVERTISSEMENT

Pour reduire les risques d’incendie, de choc

electrique ou de blessures en utilisant votre

lave-vaisselle, suivez les precautions qui

s’imposent, incluant celles qui suivent:

MESURES DE SÉCURITÉ IMPORTANTES

• Lisez toutes les instructions avant de faire

fonctionner votre lave-vaisselle.

• N’utilisez votre lave-vaisselle que selon

les instructions incluses dans ce guide

d’entretien et d’utilisation.

• Les instructions contenues dans le présent

guide d’entretien et d’utilisation ne visent

pas à couvrir toutes les situations qui

pourraient se présenter. Faites preuve de

sens pratique et prenez les précautions

qui s’imposent lors de l’installation,

l’utilisation et l’entretien de tout appareil

électroménager.

• LE CIRCUIT ÉLECTRIQUE DE CE LAVE-

VAISSELLE DOIT

ÊTRE MIS À LA TERRE.

Lisez les instructions d’installation pour de

plus amples informations.

• Ce lave-vaisselle est conçu pour fonctionner

avec un courant résidentiel normal (120

volts, 60 hertz). Utilisez un circuit équipé

d’un fusible ou un disjoncteur de 15

ampères. Utilisez un fusible de 20 ampères

si le lave-vaisselle est connecté avec un

broyeur à déchets.

• Ne faites pas fontionner le lave-vaisselle si

tous les panneaux de carrosserie ne sont

pas correctement en place.

• Pour éviter qu’une personne puisse

s’enfermer à l’intérieur de l’appareil et/ou y

suffoquer, retirez la porte ou le mécanisme

de verrouillage de porte de tout lave-

vaisselle inutilisé ou mis aux rebuts.

• Tenez vos bébés et enfants loin du lave-

vaisselle en fonctionnement.

• Ne laissez pas vos enfants faire une

utilisation abusive, s’asseoir, grimper ou

jouer sur la porte ou les paniers du lave-

vaisselle.

• Utilisez seulement les détersifs et agents de

rinçage recommandés pour lave-vaisselle.

• Placez les détersifs et agents de rinçage

hors de la portée des enfants.

• Ne modiﬁ ez pas les commandes.

AVERTISSEMENT

Lire toutes les instructions avant d’employer

cet appareil:

• Ne lavez pas les articles en plastique

à moins d’indication contraire sur les

étiquettas. S’il n y à aucune indication

à cet effet vériﬁ ez avec le fabricant. Les

articles non recommandés pour être lavés

au lave-vaisselle risquent de fondre et de

créer un reisque d’incendie.

• Si le lave-vaisselle vidange dans un broyeur

à déchets, assurez-vous que ce dernier

est complètement vide avant de mettre en

marche le lave-vaisselle.

• Débranchez l’alimentation électrique au

lave-vaisselle avant d’entreprendre tout

travail d’entretien ou de réparation.

• Pour ranger les articles dans le lave-

vaisselle:

• Ranger les couteaux et articles pointus

pour qu’ils ne risquent pas d’endommager

le joint de la porte ou la cuve.

• Placer les couteaux et articles pointus,

manches vers le haut pour réduire le

risque de coupures.

• Dans certains conditions, il est possible qu’il

se produise une formation d’hydrogène

dans la canalisation d’eau chaude in utilisée

depuis 2 semaines ou plus. L’HYDROGÈNE

EST UN GAZ EXPLOSIF. Si la canalisation

d’eau chaude n’a pas été utilisée pendant

un tel laps de temps, ouvrez tous les

robinets d’eau chaude et laissez lcouler

l’eau pendant plusieurs minutes avant

d’utiliser le lave-vaisselle. Ceci permettra

d’évacuer tout hydrogène accumulé.

L’HYDROGÈNE EST UN GAZ INFLAMMABLE.

Ne fumez ou n’allumez aucune ﬂ amme

dans une telle situation.

• Les réparations doivent être faites par un

techicien qualiﬁ é.

• Ne touchez pas l’élément chauffant

pendant ou immédiatement après

l’utilisation.

• N’entreposez et n’utilisez pas d’essences

et combustibles ou d’autres produits

inﬂ ammables à proximité de cet appareil ou

de tout autre appareil électro-ménager.

REMARQUE

Le lave-vaisselle est programmé pour se

souvenir du dernier cycle, ce qui évite

d’avoir à le reconﬁ gurer à chaque fois. Pour

démarrer le lave-vaisselle en utilisant les

options sélectionnées au cours du dernier

lavage, il sufﬁ t de tourner le bouton de

Sélectionnée sur le cycle choisi et d’enfoncer

le bouton START/CANCEL.

REMARQUE

Pas tous les cycles et les options disponibles

sur tous les modèles.

ENREGISTREMENT DE PRODUIT

Merci de choisir Frigidaire

Ce & d’utilisation Le guide de soin fait parie de

notre engagement à la satisfaction du client et

de qualité u produit durant toute la duree de

via de votre nouvel appareil.

Nous regardons votre achat comme

commencement d’un rapport. Pour assurer

notre capacité de continuer de vous servir,

employer cette page pour enregistrer

l’information sur le produit importe.

_________________________________

Date D’Achat

_________________________________

Numéro De Type

_________________________________

Numéro De Série

L’enregisterment de votre produit avec

Frigidaire augmente notre capacité de vous

servir. Vous pouvez s’enregistrer en ligne à

www.frigidaire.com ou en laissant tomber

votre carte d’registrement de produit dans le

courier.

Informations très importantes-Lisez

avant de faire fonctionner votre lave-

vaisselle!

Bruits Normaux de Fonctionnement

Ce lave-vaisselle ne génère pas le bruit

des autres lave-vaisselle-IL EST PLUS

SILENCIEUX!.

Votre lave-vaisselle avec son système de

Précision Direct se laver à de nombreuses

améliorations à réduire le niveau sonore.

Encore, il est normal d’entendre certains de

ce qui se passe à l’intérieur. Le laver cycles

comprennent plusieurs instances de l’eau

qui pénètre dans l’unité (projection), laver le

fonctionnement d’une pompe à pulveriser de

l’eau sur la vaisselle (moteur & projection) et

de l’exode discharge le fonctionnement d’une

pompe eau sale et les sols. Les variations

dans la capacité de pompage/pulvérisations

sons sont normaux. Au cours d’un cycle, la

pompe commute on et off de nombreuses

fois, et le fonctionnemnet bascule de nouveau

et entre les armes se laver à fournir les

meilleures performances de nettoyage.

VEUILLEZ PRENDRE NOTE: que si

vous comparez ce lave-vaisselle au modèles

précédents, vous serez surpris de tout ce que

vous n’entendrez pas!

Préparatifs

1. Charger le lave-vaisselle.

2. Ajouter le détergent.

3. Ajouter le produit de rinçage, si necessaire.

4. Fermer la porte à fond.

5. Sélectionner le CYCLE désirés. Le

voyant indicateur au-dessus de la plage sera

incandescent.

6. Sélectionner les OPTIONS désirés. Le

voyant indicateur au-dessus de la plage sera

incandescent.

7. Faire couler le robinet d’eau chaude le plus

proche du lave-vaisselle jusqu’à ce que l’eau

soit chaude. Fermer le robinet.

8. Pour démarrer, enfoncer le bouton START/

CANCEL.

REMARQUE

CARACTÉRISTIQUES DE LAVE - VAISSELLE

Votre lave-vaisselle lave la vaisselle et les ustensiles en faisant gicler un mélange d’eau chaude

et de détergent à travers les bras de lavage contre les surfaces souillées. Par la suite, le lave-

vaisselle se remplit d’eau de manière a recouvrir le ﬁ ltre. L’eau est ensuite pompée à travers

le ﬁ ltre et les bras de lavage. L’eau sale chargée de particules solides est pompée par le tuyau

d’écoulement et remplacée par de l’eau propre. Le nombre de remplissages d’eau dépend du

cycle sélectionné.

Choix de Cycle de Lavage

Les durées de cycle sont approximatives et

varieront avec des options choisies. L’eau

chaude est nécessaire pour activer le détergent

de lave-vaisselle et pour fondre des sols de

nourriture grasse. L’eau chaude est nécessaire

pour la meilleure vaisselle et les résultats de

séchage. Le lave-vaisselle entrant de l’eau

devrait être au moins 120

F (49

C) pour donner

des résultats satisfaisants.

FONCTIONNEMENT DE L’APPAREIL

Options (disponsible sur certains

modeles)

Cette augmentation de la température de l’eau

renforce l’action du détergent du lave-vaisselle

pour enlever la graisse des ustensiles et les

restes de nourriture plus efﬁ cacement et permet

un séchage plus rapide de la vaisselle. L’option

HI-TEMP WASH peut être utilisée avec tous

les cycles sauf RINSE ONLY. L’option HI-TEMP

WASH est fournie automatiquement lorsque

le cycle HEAVY WASH or POWER PLUS est

sélectionné.

Quand l’option HI-TEMP WASH est sélectionnée,

le voyant lumineux situé au dessus du bouton

s’allume et il ne s’éteint qu’à la ﬁ nd du cycle.

Pour annuler l’option HI-TEMP WASH, enfoncer

le bouton une deuxième fois. Le voyant au

dessus du bouton s’éteint.

Hi-Temp Wash Option

Lorsque l’option HI-TEMP WASH est

sélectionnée, le lave-vaisselle porte la

température de l’eau du lavage principal à

environ 140

F (60

C).

Les caractéristiques peuvent varier selon le modèle

Elément chauffant

Siphone de verre

Distributeur de

détergent

Protection contre

débordement

Panier à ustensiles

Pnaier inférieur

Plaque signalétique

(située sur le côté

droit de la cuve)

Panier supérieur

Ajutage et jet supérieur

Étagères à tasses

(sur quelques

modèles)

Bras de lavage

central

Bras de lavage

inférieur

Distributeur

du produit de

rinçage

Joint de la cuve

La page charge ...

Crosley CDBEH600SB2A Le manuel du propriétaire

Marque: Crosley

Modèle: CDBEH600SB2A

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Crosley CDBEH600SB2A Owner's manual

Crosley CDBEH600SB2A Le manuel du propriétaire

Ce manuel convient également à

Crosley CDBEH600SB2A Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents